Takashi Iwai [Tue, 3 May 2011 14:32:48 +0000 (16:32 +0200)]
ALSA: lola - Changes in proc file
The codec proc file becomes a read only that shows the codec widgets
in a text form. A new proc file, codec_rw, is introduced instead for
accessing the Lola verb directly by reading and writing to it.
Also, regs proc file shows the contents of DSD, too.
Takashi Iwai [Tue, 3 May 2011 14:14:46 +0000 (16:14 +0200)]
ALSA: Add the driver for Digigram Lola PCI-e boards
Added a new driver for supporting Digigram Lola PCI-e boards.
Lola has a similar h/w design like HD-audio but with extended verbs.
Thus the driver is written similarly like HD-audio driver in the bus
part. The codec part is rather written in a fixed way specific to the
Lola board because of the verb incompatibility.
The driver provides basic PCM, supporting multi-streams and mixing.
Linus Torvalds [Mon, 14 Mar 2011 22:20:39 +0000 (15:20 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
Linus Torvalds [Mon, 14 Mar 2011 22:20:12 +0000 (15:20 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
Linus Torvalds [Mon, 14 Mar 2011 22:19:09 +0000 (15:19 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
Linus Torvalds [Mon, 14 Mar 2011 22:17:07 +0000 (15:17 -0700)]
Revert "oom: oom_kill_process: fix the child_points logic"
This reverts the parent commit. I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Oleg Nesterov [Mon, 14 Mar 2011 19:05:30 +0000 (20:05 +0100)]
oom: oom_kill_process: fix the child_points logic
oom_kill_process() starts with victim_points == 0. This means that
(most likely) any child has more points and can be killed erroneously.
Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm. This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.
Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Florian Fainelli [Mon, 21 Feb 2011 13:28:02 +0000 (14:28 +0100)]
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/ Acked-by: Bruno Randolf <br1@einfach.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Sun, 27 Feb 2011 18:53:53 +0000 (19:53 +0100)]
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
Maksim Rayskiy [Sat, 12 Feb 2011 18:21:32 +0000 (10:21 -0800)]
MIPS: Move idle task creation to work queue
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
The validate_event function in the ARM perf events backend has the
following problems:
1.) Events that are disabled count towards the cost.
2.) Events associated with other PMUs [for example, software events or
breakpoints] do not count towards the cost, but do fail validation,
causing the group to fail.
This patch changes validate_event so that it ignores events in the
PERF_EVENT_STATE_OFF state or that are scheduled for other PMUs.
Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: wuzhangjin@gmail.com Cc: paulus@samba.org Cc: mingo@elte.hu Cc: acme@redhat.com Cc: dengcheng.zhu@gmail.com Cc: matt@console-pimps.org Cc: sshtylyov@mvista.com Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2013/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
For MIPSXX, the stopped state is implemented in the way of 1.b as above.
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
For MIPSXX, we need to call irq_work_run() at the tail of the perf IRQ
handler as described above.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: fweisbec@gmail.com
To: will.deacon@arm.com Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: paulus@samba.org Cc: mingo@elte.hu Cc: acme@redhat.com Cc: matt@console-pimps.org Cc: sshtylyov@mvista.com,
Patchwork: http://patchwork.linux-mips.org/patch/2011/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Mon, 24 Jan 2011 22:51:36 +0000 (14:51 -0800)]
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
GCC-4.6 can find more unused code than previous versions could.
In the case of arch/mips/math-emu/ieee754int.h, the COMPXSP and
COMPXDP macros are used in several places, but a couple of them leave
xs unused. The easiest thing to do is mark it as __maybe_unused to
quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2032/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Mon, 24 Jan 2011 22:51:34 +0000 (14:51 -0800)]
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
GCC-4.6 can find more unused code than previous versions could.
In the case of protected_restore_fp_context{,32}, the variable tmp is
really used. Its use is tricky in that we really care about the side
effects of the __put_user() calls. So we must mark tmp with
__maybe_unused to quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2035/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Anoop P A [Thu, 18 Nov 2010 10:32:50 +0000 (16:02 +0530)]
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
To: Ben Hutchings <ben@decadent.org.uk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1804/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Anoop P A [Thu, 18 Nov 2010 08:12:28 +0000 (13:42 +0530)]
MIPS: Select R4K timer lib for all MSP platforms
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1803/ Tested-by: Shane McDonald <mcdonald.shane@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Robert Millan [Sun, 7 Nov 2010 12:38:29 +0000 (13:38 +0100)]
MIPS: Loongson: Remove ad-hoc cmdline default
Loongson builds have an ad-hoc cmdline default of "console=ttyS0,115200
root=/dev/hda1". These settings come from a vendor; I remember builds
from Lemote branch requiring a "console=tty" override in order to get a
working console.
At least on Yeeloong, they're particularly useless: there's no external
serial port, and the IDE drive is now recognised as /dev/sda.
Signed-off-by: Robert Millan <rmh@gnu.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1759/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wu Zhangjin [Fri, 21 Jan 2011 18:01:53 +0000 (02:01 +0800)]
MIPS, Tracing: Fix set_graph_function of function graph tracer
trace.func should be set to the recorded ip of the mcount calling site
in the __mcount_loc section to filter the function entries configured
through the tracing/set_graph_function interface, but before, this is
set to the self_ra(the return address of mcount), which has made
set_graph_function not work as expected.
This fixes it via calculating the right recorded ip in the __mcount_loc
section and assign it to trace.func.
Wu Zhangjin [Wed, 19 Jan 2011 19:28:31 +0000 (03:28 +0800)]
MIPS, Tracing: Clean up ftrace_make_nop()
This moves the comments out of ftrace_make_nop() and cleans it. At the
same time, a macro MCOUNT_OFFSET_INSNS is defined for sharing with the
next patch.
Wu Zhangjin [Wed, 19 Jan 2011 19:28:30 +0000 (03:28 +0800)]
MIPS, Tracing: Clean up prepare_ftrace_return()
The old prepare_ftrace_return() for MIPS is confused and have introduced
some problem. This patch cleans up the names of the arguments, variables
and related functions.
For MIPS, the 2nd argument of prepare_ftrace_return() is not really the
'selfpc' described in ftrace-design.txt but instead it is the self
return address. This did break the compatibility of the generic
interface but really reduced one unneeded calculation for to get the
current function name, the parent return address and the self return
address are enough, no need to tranform the self return address to the
self address.
But set_graph_function of function graph tracer is an exception, it does
need the 2nd argument of prepare_ftrace_return() as 'selfpc', for it
will use 'selfpc' to match user's configuration of function graph
entries, but in reality, it doesn't need the 'selfpc' but the recorded
ip address of the mcount calling site in the __mcount_loc section. So,
the 2nd argument of prepare_ftrace_return() is not important, the real
requirement is the right recorded ip address should be calculated and
assign to trace.func, this will be fixed in the next patches.
Wu Zhangjin [Wed, 19 Jan 2011 19:28:29 +0000 (03:28 +0800)]
MIPS, Tracing: Substitute in_kernel_space() for in_module()
The old in_module() may not work in some situations(e.g. when module &
kernel are in the same address space when CONFIG_MAPPED_KERNEL=y), The
in_kernel_space() is more generic and it is also easy to be implemented
via cloning the existing core_kernel_text(), so, replace the in_module()
with in_kernel_space().
Wu Zhangjin [Wed, 19 Jan 2011 19:28:27 +0000 (03:28 +0800)]
MIPS, Tracing: Speed up function graph tracer
This simply moves the "ip-=4" statement down to the end of the do { ...
} while (...); loop, which reduces one unneeded subtration and the
subsequent memory loading and comparison.
Linus Torvalds [Mon, 14 Mar 2011 18:19:50 +0000 (11:19 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: NFSROOT should default to "proto=udp"
nfs4: remove duplicated #include
NFSv4: nfs4_state_mark_reclaim_nograce() should be static
NFSv4: Fix the setlk error handler
NFSv4.1: Fix the handling of the SEQUENCE status bits
NFSv4/4.1: Fix nfs4_schedule_state_recovery abuses
NFSv4.1 reclaim complete must wait for completion
NFSv4: remove duplicate clientid in struct nfs_client
NFSv4.1: Retry CREATE_SESSION on NFS4ERR_DELAY
sunrpc: Propagate errors from xs_bind() through xs_create_sock()
(try3-resend) Fix nfs_compat_user_ino64 so it doesn't cause problems if bit 31 or 63 are set in fileid
nfs: fix compilation warning
nfs: add kmalloc return value check in decode_and_add_ds
SUNRPC: Remove resource leak in svc_rdma_send_error()
nfs: close NFSv4 COMMIT vs. CLOSE race
SUNRPC: Close a race in __rpc_wait_for_completion_task()
Timo Warns [Mon, 14 Mar 2011 13:59:33 +0000 (14:59 +0100)]
Fix corrupted OSF partition table parsing
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating OSF partitions contains a bug that leaks data
from kernel heap memory to userspace for certain corrupted OSF
partitions.
In more detail:
for (i = 0 ; i < le16_to_cpu(label->d_npartitions); i++, partition++) {
iterates from 0 to d_npartitions - 1, where d_npartitions is read from
the partition table without validation and partition is a pointer to an
array of at most 8 d_partitions.
Add the proper and obvious validation.
Signed-off-by: Timo Warns <warns@pre-sense.de> Cc: stable@kernel.org
[ Changed the patch trivially to not repeat the whole le16_to_cpu()
thing, and to use an explicit constant for the magic value '8' ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 14 Mar 2011 08:08:47 +0000 (01:08 -0700)]
thp+memcg-numa: fix BUG at include/linux/mm.h:370!
THP's collapse_huge_page() has an understandable but ugly difference
in when its huge page is allocated: inside if NUMA but outside if not.
It's hardly surprising that the memcg failure path forgot that, freeing
the page in the non-NUMA case, then hitting a VM_BUG_ON in get_page()
(or even worse, using the freed page).
David Howells [Mon, 14 Mar 2011 14:45:29 +0000 (14:45 +0000)]
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
The invalidate-only versions of flush_icache_*range() are trying sending the
SMP_ICACHE_INV_FLUSH_RANGE IPI command in SMP kernels when they should be
sending SMP_ICACHE_INV_RANGE as the former does not exist.
Signed-off-by: David Howells <dhowells@redhat.com>
Tkhai Kirill [Mon, 14 Mar 2011 13:27:46 +0000 (13:27 +0000)]
MN10300: Proper use of macros get_user() in the case of incremented pointers
Using __get_user_check(x, ptr++, size) leads to double increment of pointer.
This macro uses the macro get_user directly, which itself is used in this way
(get_user(x, ptr++)) in some functions of the kernel. The patch fixes the
error.
Reported-by: Tkhai Kirill <tkhai@yandex.ru> Signed-off-by: David Howells <dhowells@redhat.com>
x86: ce4100: Set pci ops via callback instead of module init
Setting the pci ops on subsys initcall unconditionally will break
multi platform kernels on anything except ce4100.
Use x86_init.pci.init ops to call this only on real ce4100 platforms.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: sodaville@linutronix.de
LKML-Reference: <20110314093340.GA21026@www.tglx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hpwdt_init_nmi_decoding() is called in hpwdt_init_one error handling,
thus remove the __devexit annotation of hpwdt_exit_nmi_decoding().
This patch fixes below warning:
WARNING: drivers/watchdog/hpwdt.o(.devinit.text+0x36f): Section mismatch in reference from the function hpwdt_init_one() to the function .devexit.text:hpwdt_exit_nmi_decoding()
The function __devinit hpwdt_init_one() references
a function __devexit hpwdt_exit_nmi_decoding().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
hpwdt_exit_nmi_decoding() so it may be used outside an exit section.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Dave Airlie [Sun, 13 Mar 2011 23:47:24 +0000 (09:47 +1000)]
drm/radeon: fix problem with changing active VRAM size. (v2)
So we used to use lpfn directly to restrict VRAM when we couldn't
access the unmappable area, however this was removed in 93225b0d7bc030f4a93165347a65893685822d70 as it also restricted
the gtt placements. However it was only later noticed that this
broke on some hw.
This removes the active_vram_size, and just explicitly sets it
when it changes, TTM/drm_mm will always use the real_vram_size,
and the active vram size will change the TTM size used for lpfn
setting.
We should re-work the fpfn/lpfn to per-placement at some point
I suspect, but that is too late for this kernel.
Hopefully this addresses:
https://bugs.freedesktop.org/show_bug.cgi?id=35254
v2: fix reported useful VRAM size to userspace to be correct.
Al Viro [Sun, 13 Mar 2011 23:24:46 +0000 (23:24 +0000)]
compat breakage in preadv() and pwritev()
Fix for a dumb preadv()/pwritev() compat bug - unlike the native
variants, the compat_... ones forget to check FMODE_P{READ,WRITE}, so
e.g. on pipe the native preadv() will fail with -ESPIPE and compat one
will act as readv() and succeed.
Not critical, but it's a clear bug with trivial fix, so IMO it's OK for
-final.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 13 Mar 2011 23:01:11 +0000 (16:01 -0700)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon/f71882fg: Set platform drvdata to NULL later
hwmon/f71882fg: Fix a typo in a comment
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: break out of shrink_delalloc earlier
btrfs: fix not enough reserved space
btrfs: fix dip leak
Btrfs: make sure not to return overlapping extents to fiemap
Btrfs: deal with short returns from copy_from_user
Btrfs: fix regressions in copy_from_user handling
fixdep: Do not record dependency on the source file itself
changed the format of the *.cmd files without realizing that it is also
used by modpost. Put the path to the source file to the file back, in a
special variable, so that modpost sees all source files when calculating
srcversion for modules.
Reported-and-tested-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/users/dwmw2/mtd-2.6.38:
mtd: add "platform:" prefix for platform modalias
mtd: mtd_blkdevs: fix double free on error path
mtd: amd76xrom: fix oops at boot when resources are not available
mtd: fix race in cfi_cmdset_0001 driver
mtd: jedec_probe: initialise make sector erase command variable
mtd: jedec_probe: Change variable name from cfi_p to cfi
Linus Torvalds [Sun, 13 Mar 2011 22:50:01 +0000 (15:50 -0700)]
Merge branch 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Ensure WM8958 gets all WM8994 late revision widgets
ASoC: Fix typo in late revision WM8994 DAC2R name
ASoC: Use the correct DAPM context when cleaning up final widget set
ASoC: Fix broken bitfield definitions in WM8978
ASoC: AM3517: Update codec name after multi-component update
Andrea Arcangeli [Fri, 11 Mar 2011 22:58:29 +0000 (14:58 -0800)]
thp: fix page_referenced to modify mapcount/vm_flags only if page is found
When vmscan.c calls page_referenced(), if an anon page was created
before a process forked, rmap will search for it in both of the
processes, even though one of them might have since broken COW.
If the child process mlocks the vma where the COWed page belongs to,
page_referenced() running on the page mapped by the parent would lead to
*vm_flags getting VM_LOCKED set erroneously (leading to the references
on the parent page being ignored and evicting the parent page too
early).
*mapcount would also be decremented by page_referenced_one even if the
page wasn't found by page_check_address.
This also lets pmdp_clear_flush_young_notify() go ahead on a
pmd_trans_splitting() pmd.
We hold the page_table_lock so __split_huge_page_map() must wait the
pmdp_clear_flush_young_notify() to complete before it can modify the
pmd. The pmd is also still mapped in userland so the young bit may
materialize through a tlb miss before split_huge_page_map runs.
This will provide a more accurate page_referenced() behavior during
split_huge_page().
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Michel Lespinasse <walken@google.com> Reviewed-by: Michel Lespinasse <walken@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Rik van Riel<riel@redhat.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hans de Goede [Sun, 13 Mar 2011 12:50:33 +0000 (13:50 +0100)]
hwmon/f71882fg: Set platform drvdata to NULL later
This avoids a possible race leading to trying to dereference NULL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Hans de Goede [Sun, 13 Mar 2011 12:50:32 +0000 (13:50 +0100)]
hwmon/f71882fg: Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Dave Airlie [Fri, 11 Mar 2011 11:17:41 +0000 (21:17 +1000)]
drm/radeon: fix page flipping hangs on r300/r400
We've been getting reports of complete system lockups with rv3xx hw on
AGP and PCIE when running gnome-shell or kwin with compositing.
It appears the hw really doesn't like setting these registers while
stuff is running, this moves the setting of the registers into the modeset
since they aren't required to be changed anywhere else.
Chris Mason [Sat, 12 Mar 2011 12:08:42 +0000 (07:08 -0500)]
Btrfs: break out of shrink_delalloc earlier
Josef had changed shrink_delalloc to exit after three shrink
attempts, which wasn't quite enough because new writers could
race in and steal free space.
But it also fixed deadlocks and stalls as we tried to recover
delalloc reservations. The code was tweaked to loop 1024
times, and would reset the counter any time a small amount
of progress was made. This was too drastic, and with a
lot of writers we can end up stuck in shrink_delalloc forever.
The shrink_delalloc loop is fairly complex because the caller is looping
too, and the caller will go ahead and force a transaction commit to make
sure we reclaim space.
This reworks things to exit shrink_delalloc when we've forced some
writeback and the delalloc reservations have gone down. This means
the writeback has not just started but has also finished at
least some of the metadata changes required to reclaim delalloc
space.
If we've got this wrong, we're returning ENOSPC too early, which
is a big improvement over the current behavior of hanging the machine.
Test 224 in xfstests hammers on this nicely, and with 1000 writers
trying to fill a 1GB drive we get our first ENOSPC at 93% full. The
other writers are able to continue until we get 100%.
This is a worst case test for btrfs because the 1000 writers are doing
small IO, and the small FS size means we don't have a lot of room
for metadata chunks.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chuck Lever [Fri, 11 Mar 2011 20:31:06 +0000 (15:31 -0500)]
NFS: NFSROOT should default to "proto=udp"
There have been a number of recent reports that NFSROOT is no longer
working with default mount options, but fails only with certain NICs.
Brian Downing <bdowning@lavos.net> bisected to commit 56463e50 "NFS:
Use super.c for NFSROOT mount option parsing". Among other things,
this commit changes the default mount options for NFSROOT to use TCP
instead of UDP as the underlying transport.
TCP seems less able to deal with NICs that are slow to initialize.
The system logs that have accompanied reports of problems all show
that NFSROOT attempts to establish a TCP connection before the NIC is
fully initialized, and thus the TCP connection attempt fails.
When a TCP connection attempt fails during a mount operation, the
NFS stack needs to fail the operation. Usually user space knows how
and when to retry it. The network layer does not report a distinct
error code for this particular failure mode. Thus, there isn't a
clean way for the RPC client to see that it needs to retry in this
case, but not in others.
Because NFSROOT is used in some environments where it is not possible
to update the kernel command line to specify "udp", the proper thing
to do is change NFSROOT to use UDP by default, as it did before commit 56463e50.
To make it easier to see how to change default mount options for
NFSROOT and to distinguish default settings from mandatory settings,
I've adjusted a couple of areas to document the specifics.
root_nfs_cat() is also modified to deal with commas properly when
concatenating strings containing mount option lists. This keeps
root_nfs_cat() call sites simpler, now that we may be concatenating
multiple mount option strings.
Tested-by: Brian Downing <bdowning@lavos.net> Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: <stable@kernel.org> # 2.6.37 Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs4_schedule_state_recovery() should only be used when we need to force
the state manager to check the lease. If we just want to start the
state manager in order to handle a state recovery situation, we should be
using nfs4_schedule_state_manager().
This patch fixes the abuses of nfs4_schedule_state_recovery() by replacing
its use with a set of helper functions that do the right thing.
We can hit serious mis-synchronization in bio completion path of
blkdev_issue_zeroout() leading to a panic.
The problem is that when we are going to wait_for_completion() in
blkdev_issue_zeroout() we check if the bb.done equals issued (number of
submitted bios). If it does, we can skip the wait_for_completition()
and just out of the function since there is nothing to wait for.
However, there is a ordering problem because bio_batch_end_io() is
calling atomic_inc(&bb->done) before complete(), hence it might seem to
blkdev_issue_zeroout() that all bios has been completed and exit. At
this point when bio_batch_end_io() is going to call complete(bb->wait),
bb and wait does not longer exist since it was allocated on stack in
blkdev_issue_zeroout() ==> panic!
(thread 1) (thread 2)
bio_batch_end_io() blkdev_issue_zeroout()
if(bb) { ...
if (bb->end_io) ...
bb->end_io(bio, err); ...
atomic_inc(&bb->done); ...
... while (issued != atomic_read(&bb.done))
... (let issued == bb.done)
... (do the rest of the function)
... return ret;
complete(bb->wait);
^^^^^^^^
panic
We can fix this easily by simplifying bio_batch and completion counting.
Also remove bio_end_io_t *end_io since it is not used.
Signed-off-by: Lukas Czerner <lczerner@redhat.com> Reported-by: Eric Whitney <eric.whitney@hp.com> Tested-by: Eric Whitney <eric.whitney@hp.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> CC: Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org
Maxim Levitsky [Sat, 8 Jan 2011 23:25:06 +0000 (01:25 +0200)]
mtd: mtd_blkdevs: fix double free on error path
This one liner patch fixes double free that will occur if add_mtd_blktrans_dev
fails. On failure it frees the input argument, but all its users also free it
on error which is natural thing to do. Thus don't free it.
All credit for finding that bug belongs to reporters of the bug in the android bugzilla
http://code.google.com/p/android/issues/detail?id=13761
mtd: amd76xrom: fix oops at boot when resources are not available
For some unknown reasons resources needed by amd76xrom driver can be
unavailable. And instead of returning an error, the driver keeps going
and crash the kernel. This patch fixes the problem by making the driver
return -EBUSY if the resources are not available.
Commit messages tweaked by Artem.
Reported-by: Russell Whitaker <russ@ashlandhome.net> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org
As inval_cache_and_wait_for_operation() drop and reclaim the lock
to invalidate the cache, some other thread may suspend the operation
before reaching the for(;;) loop. Therefore the loop must start with
checking the chip->state before reading status from the chip.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Michael Cashwell <mboards@prograde.net> Acked-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org
Antony Pavlov [Fri, 11 Feb 2011 10:00:37 +0000 (13:00 +0300)]
mtd: jedec_probe: initialise make sector erase command variable
In the commit 08968041bef437ec363623cd3218c2b083537ada
(mtd: cfi_cmdset_0002: make sector erase command variable)
introdused a field sector_erase_cmd. In the same commit initialisation
of cfi->sector_erase_cmd made in cfi_chip_setup()
(file drivers/mtd/chips/cfi_probe.c), so the CFI chip has no problem:
Antony Pavlov [Fri, 11 Feb 2011 10:00:37 +0000 (13:00 +0300)]
mtd: jedec_probe: Change variable name from cfi_p to cfi
In the following commit, we'll need to use the CMD() macro in order to
fix the initialisation of the sector_erase_cmd field. That requires the
local variable to be called 'cfi', so change it first in a simple patch.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ariadne: remove redundant NULL check
ip6ip6: autoload ip6 tunnel
net: bridge builtin vs. ipv6 modular
ipv6: Don't create clones of host routes.
pktgen: fix errata in show results
ipv4: Fix erroneous uses of ifa_address.
vxge: update MAINTAINERS
r6040: bump to version 0.27 and date 23Feb2011
r6040: fix multicast operations
rds: prevent BUG_ON triggering on congestion map updates
bonding 802.3ad: Rename rx_machine_lock to state_machine_lock
bonding 802.3ad: Fix the state machine locking v2
drivers/net/macvtap: fix error check
net: fix multithreaded signal handling in unix recv routines
net: Enter net/ipv6/ even if CONFIG_IPV6=n
net/smsc911x.c: Set the VLAN1 register to fix VLAN MTU problem
bnx2x: fix MaxBW configuration
bnx2x: (NPAR) prevent HW access in D3 state
bnx2x: fix link notification
bnx2x: fix non-pmf device load flow
Doing my first --no-ff merge here, to get the explicit merge commit.
David did a back-merge in order to get commit 8909c9ad8ff0 ("net: don't
allow CAP_NET_ADMIN to load non-netdev kernel modules") so that we can
add Stephen Hemminger's fix to handle ip6 tunnels as well, which uses
the MODULE_ALIAS_NETDEV() macro created by that change.
Randy Dunlap [Thu, 10 Mar 2011 21:45:57 +0000 (13:45 -0800)]
net: bridge builtin vs. ipv6 modular
When configs BRIDGE=y and IPV6=m, this build error occurs:
br_multicast.c:(.text+0xa3341): undefined reference to `ipv6_dev_get_saddr'
BRIDGE_IGMP_SNOOPING is boolean; if it were tristate, then adding
depends on IPV6 || IPV6=n
to BRIDGE_IGMP_SNOOPING would be a good fix. As it is currently,
making BRIDGE depend on the IPV6 config works.
Reported-by: Patrick Schaaf <netdev@bof.de> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Doe, YiCheng [Thu, 10 Mar 2011 20:00:21 +0000 (14:00 -0600)]
ipmi: Fix IPMI errors due to timing problems
This patch fixes an issue in OpenIPMI module where sometimes an ABORT command
is sent after sending an IPMI request to BMC causing the IPMI request to fail.
Signed-off-by: YiCheng Doe <yicheng.doe@hp.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Acked-by: Tom Mingarelli <thomas.mingarelli@hp.com> Tested-by: Andy Cress <andy.cress@us.kontron.com> Tested-by: Mika Lansirine <Mika.Lansirinne@stonesoft.com> Tested-by: Brian De Wolf <bldewolf@csupomona.edu> Cc: Jean Michel Audet <Jean-Michel.Audet@ca.Kontron.com> Cc: Jozef Sudelsky <jozef.sudolsky@elbiahosting.sk> Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 10 Mar 2011 21:16:01 +0000 (13:16 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs/dcache: allow d_obtain_alias() to return unhashed dentries
Check for immutable/append flag in fallocate path
sysctl: the include of rcupdate.h is only needed in the kernel
fat: fix d_revalidate oopsen on NFS exports
jfs: fix d_revalidate oopsen on NFS exports
ocfs2: fix d_revalidate oopsen on NFS exports
gfs2: fix d_revalidate oopsen on NFS exports
fuse: fix d_revalidate oopsen on NFS exports
ceph: fix d_revalidate oopsen on NFS exports
reiserfs xattr ->d_revalidate() shouldn't care about RCU
/proc/self is never going to be invalidated...
Linus Torvalds [Thu, 10 Mar 2011 21:09:26 +0000 (13:09 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize the broadcast assist unit base destination node id properly
x86, numa: Fix numa_emulation code with memory-less node0
x86, build: Make sure mkpiggy fails on read error
Linus Torvalds [Thu, 10 Mar 2011 21:08:59 +0000 (13:08 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix sched rt group scheduling when hierachy is enabled
Linus Torvalds [Thu, 10 Mar 2011 21:07:38 +0000 (13:07 -0800)]
Merge branch 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf symbols: Avoid resolving [kernel.kallsyms] to real path for buildid cache
perf symbols: Fix vmlinux path when not using --symfs
drm/i915: Do not handle backlight combination mode specially
since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.
In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).
projects / karo-tx-linux.git / log