Jesse Barnes [Wed, 5 Nov 2014 22:26:06 +0000 (14:26 -0800)]
drm/i915: factor out compute_config from __intel_set_mode v3
This allows us to calculate the full pipe config before we do any mode
setting work.
v2:
- clarify comments about global vs. per-crtc mode set (Ander)
- clean up unnecessary pipe_config = NULL setting (Ander)
v3:
- fix pipe_config handling (alloc in compute_config, free in set_mode) (Jesse)
- fix arg order in set_mode (Jesse)
- fix failure path of set_config (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 13:20:23 +0000 (15:20 +0200)]
drm/i915: Remove most INVALID_PIPE checks from the backlight code
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 13:19:46 +0000 (15:19 +0200)]
drm/i915: Register the backlight device after the modeset init
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 09:16:02 +0000 (11:16 +0200)]
drm/i915: Pass the current pipe from eDP init to backlight setup
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 09:16:01 +0000 (11:16 +0200)]
drm/i915: Don't deref NULL crtc in intel_get_pipe_from_connector()
If the connector would have an encoder but the encoder didn't have a
crtc we might dereference a NULL crtc here. I suppose that should never
happen due to intel_sanitize_encoder(), but let's be a bit paranoid
print a warning if we ever hit this and return INVALID_PIPE to the
caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 13:18:45 +0000 (15:18 +0200)]
drm/i915: Skip .get_backlight() when backlight isn't enabled
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com> Suggested-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 7 Nov 2014 09:15:59 +0000 (11:15 +0200)]
drm/i915: Warn if trying to poke a VLV backlight on invalid pipe
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Tue, 4 Nov 2014 12:51:40 +0000 (04:51 -0800)]
drm/i915: Make the physical object coherent with GTT
Currently objects for which the hardware needs a contiguous physical
address are allocated a shadow backing storage to satisfy the contraint.
This shadow buffer is not wired into the normal obj->pages and so the
physical object is incoherent with accesses via the GPU, GTT and CPU. By
setting up the appropriate scatter-gather table, we can allow userspace
to access the physical object via either a GTT mmaping of or by rendering
into the GEM bo. However, keeping the CPU mmap of the shmemfs backing
storage coherent with the contiguous shadow is not yet possible.
Fortuituously, CPU mmaps of objects requiring physical addresses are not
expected to be coherent anyway.
This allows the physical constraint of the GEM object to be transparent
to userspace and allow it to efficiently render into or update them via
the GTT and GPU.
v2: Fix leak of pci handle spotted by Ville
v3: Remove the now duplicate call to detach_phys_object during free.
v4: Wait for rendering before pwrite. As this patch makes it possible to
render into the phys object, we should make it correct as well!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 5 Nov 2014 18:48:48 +0000 (20:48 +0200)]
drm/i915: move rps irq enable/disable to i915_irq.c
The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 5 Nov 2014 18:48:42 +0000 (20:48 +0200)]
drm/i915: unify gen6/gen8 rps irq enable/disable
The GEN6 and GEN8 versions differ only in the PM IIR and IER register
addresses and that on GEN8 we need to keep the
GEN8_PMINTR_REDIRECT_TO_NON_DISP PM interrupt unmasked. Abstract away
these 3 things in the GEN6 versions of the helpers and use them
everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 5 Nov 2014 18:48:37 +0000 (20:48 +0200)]
drm/i915: unify gen6/gen8 rps irq handler
After the previous patch the GEN8 RPS handler became very similar to the
GEN6 version, so unify the two functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Move one misplaced hunk from a later patch to fix a bisect
issue as reported by Wu Fengguang's 0-day builder and fix suggested by
Imre.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Wed, 5 Nov 2014 18:48:31 +0000 (20:48 +0200)]
drm/i915: unify gen6/gen8 pm irq helpers
The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 10 Nov 2014 16:47:30 +0000 (14:47 -0200)]
drm/i915: use the correct obj when preparing the sprite plane
Commit "drm/i915: create a prepare phase for sprite plane updates"
changed the old_obj pointer we use when committing sprite planes,
which caused a WARN() and a BUG() to be triggered. Later, commit
"drm/i915: use intel_fb_obj() macros to assign gem objects" introduced
the same problem to function intel_commit_sprite_plane().
Regression introduced by:
commit ec82cb793c9224e0692eed904f43490cf70e8258
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:32 2014 +0100
drm/i915: create a prepare phase for sprite plane updates
and:
commit 77cde95217484e845743818691df026cec2534f4
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Fri Oct 24 14:51:33 2014 +0100
drm/i915: use intel_fb_obj() macros to assign gem objects
Credits to Imre Deak for pointing out the exact lines that were wrong.
v2: Also fix intel_commit_sprite_plane() (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85634
Testcase: igt/pm_rpm/legacy-planes
Testcase: igt/pm_rpm/legacy-planes-dpms
Testcase: igt/pm_rpm/universal-planes
Testcase: igt/pm_rpm/universal-planes-dpms Credits-to: Imre Deak <imre.deak@intel.com> Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Add tracepoints to track a vm during its lifetime
- ppgtt init/release: these tracepoints are useful for observing the
creation and destruction of Full PPGTTs.
- ctx create/free: we can use the ctx_free trace in combination with the
ppgtt_release one to be sure that the ppgtt doesn't stay alive for too
long after the ctx is destroyed. ctx_create is there for simmetry
- switch_mm: important point in the lifetime of the vm
v4: add DOC information
v5: pull the DOC in drm.tmpl
v6: clean ppgtt init/release traces + add ctx create/free and switch_mm
tracepoints (Chris)
v7: drop execlist_submit_context tracepoint
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 28 Oct 2014 14:20:48 +0000 (16:20 +0200)]
drm/edid: fix Baseline_ELD_Len field in drm_edid_to_eld()
The Baseline_ELD_Len field does not include ELD Header Block size.
From High Definition Audio Specification, Revision 1.0a:
The header block is a fixed size of 4 bytes. The baseline block
is variable size in multiple of 4 bytes, and its size is defined
in the header block Baseline_ELD_Len field (in number of
DWords).
Do not include the header size in Baseline_ELD_Len field. Fix all known
users of eld[2].
While at it, switch to DIV_ROUND_UP instead of open coding it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Acked-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Dave Airlie <airlied@linux.ie>
[danvet: Fix compile fail in nouveau.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: avoid deadlock on failure paths in __intel_framebuffer_create()
Since a8bb6818270c __intel_framebuffer_create() is called
with struct_mutex held, so it should use drm_gem_object_unreference()
instead of drm_gem_object_unreference_unlocked().
Found by Linux Driver Verification project (linuxtesting.org).
Bob Paauwe [Tue, 11 Nov 2014 17:29:18 +0000 (09:29 -0800)]
drm/i915: Use correct pipe config to update pll dividers. V2
Use the new pipe config values to calculate the updated pll dividers.
This regression was introduced in
commit 0dbdf89f27b17ae1eceed6782c2917f74cbb5d59
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:33 2014 +0200
drm/i915: Add infrastructure for choosing DPLLs before disabling crtcs
and
commit 00d958817dd3daaa452c221387ddaf23d1e4c06f
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Wed Oct 29 11:32:36 2014 +0200
drm/i915: Covert remaining platforms to choose DPLLS before disabling CRTCs
v2: Use intel_pipe_will_have_type() to look at new configuration - Ander
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com> CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Plug memory leak in intel_shared_dpll_start_config()
The cleanup path would reset pll->new_config to NULL but wouldn't free
the allocated memory.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Sun, 9 Nov 2014 23:59:16 +0000 (09:59 +1000)]
Merge tag 'topic/atomic-helpers-2014-11-09' of git://anongit.freedesktop.org/drm-intel into drm-next
So here's my atomic series, finally all debugged&reviewed. Sean Paul has
done a full detailed pass over it all, and a lot of other people have
commented and provided feedback on some parts. Rob Clark also converted
msm over the w/e and seems happy. The only small thing is that Rob wants
to export the wait_for_vblank, which imo makes sense. Since there's other
stuff still to do I think we should apply Rob's patch (once it has grown
appropriate kerneldoc) later on top of this.
This is just the core<->driver interface plus a big pile of helpers. Short
recap of the main ideas:
- There are essentially three helper libraries in this patch set:
* Transitional helpers to use the new plane callbacks for legacy plane
updates and in the crtc helper's ->mode_set callback. These helpers are
only temporarily used to convert drivers to atomic, but they allow a
nice separation between changing the driver backend and switching to
the atomic commit logic.
* Legacy helpers to implement all the legacy driver entry points
(page_flip, set_config, plane vfuncs) on top of the new atomic driver
interface. These are completely driver agnostic. The reason for having
the legacy support as helpers is that drivers can switch step-by-step.
And they could e.g. even keep the legacy page_flip code around for some
old platforms where converting to full-blown atomic isn't worth it.
* Atomic helpers which implement the various new ->atomic_* driver
interfaces in terms of the revised crtc helper and new plane helper
hooks.
- The revised crtc helper implemenation essentially implements all the
lessons learned in the i915 modeset rework (when using the atomic helpers
only):
* Enable/disable sequence for a given config are always the same and
callbacks are always called in the same order. This contrast starkly
with the crtc helpers, where the sequence of operations is heavily
dependent on the previous config.
One corollary of this is that if the configuration of a crtc only
partially changes (e.g. a connector moves in a cloned config) the
helper code will still disable/enable the full display pipeline. This
is the only way to ensure that the enable/disable sequence is always
the same.
* It won't call disable or enable hooks more than once any more because
it lost track of state, thanks to the atomic state tracking. And if
drivers implement the ->reset hook properly (by either resetting the hw
or reading out the hw state into the atomic structures) this even
extends to the hardware state. So no more disable-me-harder kind of
nonsense.
* The only thing missing is the hw state readout/cross-check support, but
if drivers have hw state readout support in their ->reset handlers it's
simple to extend that to cross-check the hw state.
* The crtc->mode_set callback is gone and its replacement only sets crtc
timings and no longer updates the primary plane state. This way we can
finally implement primary planes properly.
- The new plane helpers should be suitable enough for pretty much
everything, and a perfect fit for hardware with GO bits. Even if they
don't fit the atomic helper library is rather flexible and exports all
the functions for the individual steps to drivers. So drivers can pick
what matches and implement their own magic for everything else.
- A big difference compared to all previous atomic series is that this one
doesn't implement async commit in a generic way. Imo driver requirements
for that are too diverse to create anything reasonable sane which would
actually work on a reasonable amount of different drivers. Also, we've
never had a helper library for page_flips even, so it's really hard to
know what might work and what's stupid without a bit of experience in the form
of a few driver implementations.
I think with the current flexibility for drivers to pick individual
stages and existing helpers like drm_flip_queue it's rather easy though
to implement proper async commit.
- There's a few other differences of minor importance to earlier atomic
series:
* Common/generic properties are parsed in the callers/core and not in
drivers, and passed to drivers by directly setting the right members in
atomic state structures. That greatly simplifies all the transitional
and legacy helpers an removes a lot of boilerplate code.
* There's no crazy trylock mode used for the async commit since these
helpers don't do async commit. A simple ordered flip queue of atomic
state updates should be sufficient for preventing concurrent hw access
anyway, as long as synchronous updates stall correctly with e.g.
flush_work_queue or similar function. Abusing locks to enforce ordering
isn't a good idea imo anyway.
* These helpers reuse the existing ->mode_fixup hooks in the atomic_check
callback. Which means that drivers need to adapat and move a lot less code
into their atomic_check callbacks.
Now this isn't everything needed in the drm core and helpers for full
atomic support. But it's enough to start with converting drivers, and
except for actually testing multiplane and multicrtc updates also enough to
implement full atomic updates. Still missing are:
- Per-plane locking. Since these helpers here encapsulate the locking
completely this should be fairly easy to implement.
- fbdev support for atomic_check/commit, so that multi-pipe finally works
sanely in fbcon.
- Adding and decoding shared/core properties. That just needs to be rebased
from Rob's latest patch series, with minor adjustments so that the
decoding happens in the core instead of in drivers.
- Actually adding the atomic ioctl. Again just rebasing Rob's latest patch
should be all that's needed.
- Resolving how to deal with DPMS in atomic. Atomic is a good excuse to fix up
the crazy semantics dpms currently has. I'm floating an RFC about this topic
already.
- Finally I couldn't test connector/encoder stealing properly since my test
vehicle here doesn't allow a connector on different crtcs. So drivers
which support this might see some surprises in that area. There is no semantic
change though in how encoder stealing and assignment works (or at least no
intended one), so I think the risk is minimal.
As just mentioned I've done a fake conversion of an existing driver using
crtc helpers to debug the helper code and validate the smooth transition
approach. And that smooth transition was the really big motivation for
this. It seems to actually work and consists of 3 phases:
Phase 1: Rework driver backend for crtc/plane helpers
The requirement here is that universal plane support is already implement. If
universal plane support isn't implement yet it might be better though to just do
it as part of this phase, directly using the new plane helpers. There are two
big things to do:
- Split up the existing ->update/disable_plane hooks into check/commit
hooks and extract the crtc-wide prep/flush parts (like setting/clearing
GO bits).
- The other big change is to split the crtc->mode_set hook into the plane
update (done using the plane helpers) and the crtc setup in a new
->mode_set_nofb hook.
When phase 1 is complete the driver implements all the new callbacks which
push the software state into hardware, but still using all the legacy entry
points and crtc helpers. The transitional helpers serve as impendance
mismatch here.
Phase 2: Rework state handling
This consists of rolling out the state handling helpers for planes, crtcs
and connectors and reviewing all ->mode_fixup and similar hooks to make
sure they don't depend upon implicit global state which might change in the
atomic world. Any such code must be moved into ->atomic_check functions which
just rely on the free-standing atomic state update structures.
This phase also adds a few small pieces of fixup code to make sure the
atomic state doesn't get out of sync in the legacy driver callbacks.
Phase 3: Roll out atomic support
Now it's just about replacing vfuncs with the ones provided by the helper
and filling out the small missing pieces (like atomic_check logic or async
commit support needed for page_flips). Due to the prep work in phase 1 no
changes to the driver backend functions should be required, and because of
the prep work in phase 2 atomic implementations can be rolled out
step-by-step. So if async commit ins't implemented yet page_flip can be
implemented with the legacy functions without wreaking havoc in the other
operations.
* tag 'topic/atomic-helpers-2014-11-09' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Refcounting for plane_state->fb
drm: Docbook integration and over sections for all the new helpers
drm/atomic-helpers: functions for state duplicate/destroy/reset
drm/atomic-helper: implement ->page_flip
drm/atomic-helpers: document how to implement async commit
drm/atomic: Integrate fence support
drm/atomic-helper: implementatations for legacy interfaces
drm: Atomic crtc/connector updates using crtc/plane helper interfaces
drm/crtc-helper: Transitional functions using atomic plane helpers
drm/plane-helper: transitional atomic plane helpers
drm: Add atomic/plane helpers
drm: Global atomic state handling
drm: Add atomic driver interface definitions for objects
drm/modeset_lock: document trylock_only in kerneldoc
drm: fixup kerneldoc in drm_crtc.h
drm: Pull drm_crtc.h into the kerneldoc template
drm: Move drm_crtc_init from drm_crtc.h to drm_plane_helper.h
Ville Syrjälä [Tue, 7 Oct 2014 14:41:22 +0000 (17:41 +0300)]
drm/i915: Cache HPLL frequency on VLV/CHV
We need the HPLL frequency when calculating cdclk. Currently we read
that out from the hardware every single time, which isn't going to fly
very well if the device is runtime suspended. So cache the HPLL
frequency in dev_priv and use the cached value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939 Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While the relevance for WaRsDontPollForAckOnClearingFWBits is under
investigation, revert this as regression.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85684 Tested-by: Tested-by: lu hua <huax.lu@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: S, Deepak <deepak.s@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Make mmio flip wait for seqno in the work function
This simplifies the code quite a bit compared to iterating over all
rings during the ring interrupt.
Also, it allows us to drop the mmio_flip spinlock, since the mmio_flip
struct is only accessed in two places. The first is when the flip is
queued and the other when the mmio writes are done. Since a flip cannot
be queued while there is a pending flip, the two paths shouldn't ever
run in parallel. We might need to revisit that if support for replacing
flips is implemented though.
v2: Don't hold dev->struct_mutext while waiting (Chris)
v3: Make the wait uninterruptable (Chris)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Make __wait_seqno non-static and rename to __i915_wait_seqno
So that it can be used by the flip code to wait for rendering without
holding any locks.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 6 Nov 2014 12:49:12 +0000 (14:49 +0200)]
drm/i915: Move the .global_resources() hook call into modeset_update_crtc_power_domains()
We may need to access various hardware bits in the .global_resources()
hook, so move the call to occur after enabling all the newly required
power wells, but before disabling all the now unneeded wells. This
should guarantee that we have all the sufficient hardware resources
available during the .global_resources() call. And if not, any additional
resources must be explicitly acquired by the .global_resorces() hook.
For instance on VLV/CHV we need to access the gunit mailbox so that we
can talk to punit/cck over sideband. In addition some PFI credit
reprogramming may need to be addes as well, which may require the disp2d
well.
This should also make the power domain refcounts consistent on platforms
which don't have a .global_resource() hook since now they too will
call modeset_update_crtc_power_domains() which will drop the init power.
Previously init power was just left enabled for such platforms.
Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:02 +0000 (17:07 +0000)]
drm/i915/skl: Flush the WM configuration
When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.
As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.
v2: Don't wait for pipes that are off
v3: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v4: Rework and document the algorithm after Ville found that it was all
wrong.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:01 +0000 (17:07 +0000)]
drm/i915/skl: Stage the pipe DDB allocation
To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.
This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:58 +0000 (17:06 +0000)]
drm/i915/skl: Rework when the transition WMs are computed
The transition WMs code was doing a shortcut and the values were copied
from the WM0 ones at compute_wm_results() time. Going forward, we want
to compute them like the other WMs and resolve their final register
values in the same way as well.
This patch does just that and isolate the transtion WM compute code in
skl_compute_transition_wm() while skl_compute_wm_results() takes care of
the register values.
We also take the opportunity to disable the transition WMs for now.
We've noticed underruns and they seem to be the culprit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:55 +0000 (17:06 +0000)]
drm/i915/skl: Make res_blocks/lines intermediate values 32 bits
To align with the ilk WM code and because it makes sense to test against
the upper bounds as soon as possible on variables that are bigger than
the number of bits in the register, let's move the maximum checks from
skl_compute_wm_results() to skl_compute_plane_wm().
v2: Leave the result values to 0 when overflowing the limits (Ville)
Use 32 bits intermediate variables (Damien)
Instead of using the 16 and 8 bits space we have in the result
structure, use 32 bits local variables until we're sure they fit into
the constraints.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:51 +0000 (17:06 +0000)]
drm/i915/skl: Add a debugfs file to dump the DDB allocation
v2: minor conflict in i915_debugfs.c
v3: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v4: minor conflict in the i915_debugfs_files array
v5: minor conflict in the i915_debugfs_files array
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Tue, 4 Nov 2014 17:06:47 +0000 (17:06 +0000)]
drm/i915/gen9: Disable WM if corresponding latency is 0
According to updated BSpec, If level 1 or any higher level has a value of 0x00,
that level and any higher levels are unused and the associated watermark
registers must not be enabled.
This patch checks for latency 0 for level >=1 and does not enable WM
corresponding to level m | m>=n, if level n (n != 0) has a 0us latency.
v2: Satheesh's review comments
- zero-out latency values (for all higher levels if latency of given
level is zero ) in read_wm_latency() function itself
v3: removed redundant check as per Satheesh's observation.
v4: rebase on top before merging (Damien)
v5: Rebase on top of the default value removal (Ville)
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3) Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Tue, 4 Nov 2014 17:06:46 +0000 (17:06 +0000)]
drm/i915/gen9: Add 2us read latency to WM level
According to the updated Bspec, The mailbox response data is not currently
accounting for memory read latency. Add 2 microseconds to the result for
each level.
This patch adds 2us to latency of level 0 for all cases and
for all other levels (1-7) only if latency[level] > 0.
v2: Slightly rework the patch and add a big comment (Damien)
v3: Rebase on top of the renames of the memory latency defines
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v1) Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2) Reviewed-by: M, Satheeshakrishna <satheeshakrishna.m@intel.com> (v1) Cc: Lespiau, Damien <damien.lespiau@intel.com> Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:45 +0000 (17:06 +0000)]
drm/i915/skl: Read the pipe WM HW state
This patch provides the implementation for reading the pipe wm HW
state.
v2: Incorporated Damien's review comments and also made modifications
to incorporate the plane/cursor split.
v3: No need to ident a line that was fitting 80 chars
Return early instead of indenting the remaining of a function
(Damien)
v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:43 +0000 (17:06 +0000)]
drm/i915/skl: Allocate DDB portions for display planes
v2: Fix the 3rd plane/cursor logic (Pradeep Bhat)
v3: Fix one-by-one error in the DDB allocation code
v4: Rebase on top of the skl_pipe_pixel_rate() argument change
v5: Replace the available/start/end output parameters of
skl_ddb_get_pipe_allocation_limits() by a single ddb entry constify
a few arguments
Make nth_active_pipe 0 indexed
Use sizeof(variable) instead of sizeof(type)
(Ville)
v6: Use the for_each_crtc() macro instead of list_for_each_entry()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:42 +0000 (17:06 +0000)]
drm/i915/skl: SKL Watermark Computation
This patch implements the watermark algorithm and its necessary
functions. Two function pointers skl_update_wm and
skl_update_sprite_wm are provided. The skl_update_wm will update
the watermarks for the crtc provided as an argument and then
checks for change in DDB allocation for other active pipes and
recomputes the watermarks for those Pipes and planes as well.
Finally it does the register programming for all dirty pipes.
The trigger of the Watermark double buffer registers will have
to be once the plane configurations are done by the caller.
v2: fixed the divide-by-0 error in the results computation func.
Also reworked the PLANE_WM register values computation func to
make it more compact. Incorporated all other review comments
from Damien.
v3: Changed the skl_compute_plane_wm function to now return success
or failure. Also the result blocks and lines are computed here
instead of in skl_compute_wm_results function.
v4: Adjust skl_ddb_alloc_changed() to the new planes/cursor split
(Damien)
v5: Reworked the affected functions to implement new plane/cursor
split.
v6: Rework the logic that triggers the DDB allocation and WM computation
of skl_update_other_pipe_wm() to not depend on non-computed DDB
values.
Always give a valid cursor_width (at boot it's 0) to keep the
invariant that we consider the cursor plane always enabled.
Otherwise we end up dividing by 0 in skl_compute_plane_wm()
(Damien Lespiau)
v7: Spell out allocation
skl_ddb_ functions should have the ddb as first argument
Make the skl_ddb_alloc_changed() parameters const
(Damien)
v8: Rebase on top of the crtc->primary changes
v9: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v10: Make skl_pipe_pixel_rate() take a pointer to the pipe config
Add a comment about overflow considerations for skl_wm_method1()
Various additions of const
Various use of sizeof(variable) instead of sizeof(type)
Various move of variable definitons to a narrower scope
Zero initialize some stack allocated structures to make sure we
don't have garbage in case we don't write all the values
(Ville)
v11: Remove non-necessary default number of blocks/lines when the plane
is disabled (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now need to allocate space in the DDB for planes being scanned out
ourselves. The data structure to represent an allocation mirrors what
we'll need to write in the registers later on: (start, end).
We add that allocation datat to the skl_wm_values structure as part of
the values to program the hardware with.
v2: Split planes and cursor for consistency.
v3: Make the skl_ddb_entry_size() parameter const
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:40 +0000 (17:06 +0000)]
drm/i915/skl: Definition of SKL WM param structs for pipe/plane
This patch defines the structures needed for computation of
watermarks of pipes and planes for SKL.
v2: Incorporated Damien's review comments and removed unused fields
in structs for future features like rotation, drrs and scaling.
The skl_wm_values struct is now made more generic across planes
and cursor planes for all pipes.
v3: implemented the plane/cursor split.
v4: Change the wm union back to a structure (Ville, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:39 +0000 (17:06 +0000)]
drm/i915/skl: Register definitions and macros for SKL Watermark regs
This patch defines SKL specific PLANE_WM Watermark registers. It also
defines macros to get the addresses of different LP levels within a pipe.
v2: Reworked the register definitions and associated macros to make it more
generic and be able to use for_each_pipe in values computation.
Incorporated Damien's review comments and indentation.
v3: Added default values for lines and blocks. Provided mask for blocks.
v4: Prefix intermedidate (internal-only) macros with _ (Ville)
v5: Remove the lines and block defaults value (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4) Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:38 +0000 (17:06 +0000)]
drm/i915/skl: Read the Memory Latency Values for WM computation
This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com> Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's some serious confusion regarding ELD valid bit that gets set and
cleared back and forth etc. Rewrite it all based on the documented audio
codec enable/disable sequences.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:52 +0000 (16:26 +0200)]
drm/i915: clean up and clarify audio related register defines
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 24 Oct 2014 11:11:11 +0000 (12:11 +0100)]
drm/i915: Report the actual swizzling back to userspace
Userspace cares about whether or not swizzling depends on the page
address for its direct access into bound objects. Extend the get_tiling
ioctl to report the physical swizzling value in addition to the logical
swizzling value so that userspace can accurately determine when it is
possible for manual detiling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Akash Goel <akash.goel@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Testcase: igt/gem_tiled_wc Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 31 Oct 2014 13:53:53 +0000 (13:53 +0000)]
drm/i915: Request PIN_GLOBAL when pinning a vma for GTT relocations
Always require PIN_GLOBAL when we want a mappable offset (PIN_MAPPABLE).
This causes the pin to fixup the global binding in cases were the vma
was already bound (and due to the proceeding bug, we considered it to be
already mappable).
References: https://bugs.freedesktop.org/show_bug.cgi?id=85671 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add WARN_ON to check that PIN_MAP implies PIN_GLOBAL as
discussed on irc.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 31 Oct 2014 13:53:52 +0000 (13:53 +0000)]
drm/i915: Only mark as map-and-fenceable when bound into the GGTT
We use the obj->map_and_fenceable hint for when we already have a
valid mapping of this object in the aperture. This hint can only apply
to the GGTT and not to the aliasing-ppGTT. One user of the hint is
execbuffer relocation, which began to fail when it tried to follow the
hint and perform the relocate through the non-existent GGTT mapping.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85671 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.
v2: Explain the need for mmio_flip.work in the commit message (Paulo)
Initialize the mmio_flip work in intel_crtc_init() (Paulo)
Prevent new flips the previous flip work finishes (Paulo)
Don't acquire modeset locks for mmio flip work
Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Remove modeset lock check from intel_pipe_update_start()
A follow up patch will call this funcion from a work context for the
mmio flip, in which case we cannot acquire the modeset locks. That's
not a problem though, since the check is there to protect vblank and
the mode, but the code that changes that waits for pending flips
first.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Add kerneldoc for intel_pipe_update_{start, end}
Note that a later patch will use these functions in some other file
and drop the static. Hence the kerneldoc looks appropriate.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add comment that the functions will become non-static
shortly.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Thu, 30 Oct 2014 18:40:53 +0000 (18:40 +0000)]
drm/i915: Remove redundant parameter to i915_gem_object_wait_rendering__tail()
An earlier commit (c8725f3dc0911d4354315a65150aecd8b7d0d74a: Do not call
retire_requests from wait_for_rendering) removed the use of the ring parameter
within wait_rendering__tail() but did not remove the parameter itself. As the
plan is to remove obj->ring which is where this parameter comes from, it is
simpler to just remove the parameter completely than to update it with a new
source.
For: VIZ-4377 Signed-off-by: John Harrison <John.C.Harrison@Intel.com> CC: Chris Wilson <chris@chris-wilson.co.uk> CC: Brad Volkin <bradley.d.volkin@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 30 Oct 2014 17:59:31 +0000 (15:59 -0200)]
drm/i915: fix RPS on runtime suspend
With this patch, the RPS sequence for runtime suspend/resume is
exactly like the sequence for S3 suspend/resume:
- flush_delayed_work(&dev_priv->rps.delayed_resume_work)
- intel_runtime_pm_disable_interrupts()
- intel_suspend_gt_powersave()
(suspended)
- intel_runtime_pm_enable_interrupts()
- intel_enable_gt_powersave()
With this, we get rid of WARNs that are currently intermittently
triggered by the system-suspend-execbuf subtest of runtime PM. Notice
that these WARNs could also be triggered in other ways that involved
doing lots of RPM suspend/resume cycles just after a system S3 resume.
Testcase: igt/pm_rpm/system-suspend-execbuf Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939 Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: properly clear IIR at irq_uninstall on Gen5+
so we can kill the leftovers from the vlv code.
Cc: Paulo Zanoni <przanoni@gmail.com> Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:43:01 +0000 (19:43 +0200)]
drm/i915: Drop useless VLV_IIR writes from vlv_display_irq_postinstall()
The extra VLV_IIR writes at the end of vlv_display_irq_postinstall()
serve no purpose. Remove them.
The VLV_IMR/IER/IIR setup at the start of the function also seems a bit
pointless since it doesn't unmask/enable anything. But leave it be for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:43:00 +0000 (19:43 +0200)]
drm/i914: Refactor vlv_display_irq_postinstall()
Split the vlv display irq postinstall code to a separate function so
that we can share it with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:58 +0000 (19:42 +0200)]
drm/i915: Refactor vlv_display_irq_reset()
Pull the vlv display irq reset code to a new functions. The aim is to
share the code with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:57 +0000 (19:42 +0200)]
drm/i915: Make valleyview_display_irqs_(un)install() work for chv
Genralize valleyview_display_irqs_install() and
valleyview_display_irqs_uninstall() enough so that they work on chv.
The only difference to vlv here being the third pipe that chv brings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:56 +0000 (19:42 +0200)]
drm/i915: Call gen5_gt_irq_reset() from valleyview_irq_uninstall()
Looks like we forgot to call gen5_gt_irq_reset() for vlv in the
uninstall phase. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:55 +0000 (19:42 +0200)]
drm/i915: Use GEN5_IRQ_RESET() on vlv/chv
Replace the hand rolled IIR,IER,IMR disable sequences with
GEN5_IRQ_RESET().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:54 +0000 (19:42 +0200)]
drm/i915: Use a consistent order between IIR, IER, IMR writes on vlv/chv
Follow the same ordering rules for the IIR,IER,IMR writes on vlv/chv
that we do on other gen5+ platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:53 +0000 (19:42 +0200)]
drm/i915: Drop the extra GEN8_PCU_IIR posting read from cherryview_irq_preinstall()
Looks like a leftover POSTING_READ(GEN8_PCU_IIR) in
cherryview_irq_preinstall() from some earlier age. GEN5_IRQ_RESET()
already does the posting read so this changes nothing, so kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:52 +0000 (19:42 +0200)]
drm/i915: Use gen8_gt_irq_reset() in cherryview_irq_uninstall()
Replace the hand rolled macros with gen8_gt_irq_reset() and
GEN5_IRQ_RESET() in cherryview_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:51 +0000 (19:42 +0200)]
drm/i915: Use DPINVGTT_STATUS_MASK
Some has given a name for the DPINVGTT status bitmask, so let's use it
instead of the magic number. Looks more like the chv code now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:50 +0000 (19:42 +0200)]
drm/i915: Apply some ocd for IMR vs. IER order during irq enable
When disabling interrupts we do the writes in this order:
IMR,IER,IIR,IIR. But when enabling interrupts we don't do use the
mirrored order, and instead do IIR,IIR,IMR,IER.
I like consistency unless there's a good reason against it, which I
can't think of here, so change the enable order to IIR,IIR,IER,IMR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thomas Daniel [Wed, 29 Oct 2014 09:52:51 +0000 (09:52 +0000)]
drm/i915/bdw: Setup global hardware status page in execlists mode
Write HWS_PGA address even in execlists mode as the global hardware status
page is still required. This address was previously uninitialized and
HWSP writes would clobber whatever buffer happened to reside at GGTT
address 0.
v2: Break out hardware status page setup into a separate function.
Issue: VIZ-2020 Signed-off-by: Thomas Daniel <thomas.daniel@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Nov 2014 10:39:24 +0000 (11:39 +0100)]
drm/i915/dp: Don't stop the link when retraining
On pre-ddi platforms we don't shut down the link when changing link
training parameters. Except when clock recovery fails too hard and we
restart with channel eq training. Which doesn't make a lot of sense
really, since just stopping/restarting the DP port at this point
violates the modeset sequence documented in the Bspec.
drm/i915: Drop now misleading DDI comment from dp_link_down
References: https://bugs.freedesktop.org/show_bug.cgi?id=85670 Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Acked-by: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Nov 2014 14:04:55 +0000 (15:04 +0100)]
drm/i915: Move pll state commit into intel_modeset_update_state
It's really part of the "push all new_* state into current state
pointers" done in that function. So let's move it there to make this
clear.
Also, with the conversion done the num_shared_dpll check the function
does in it's loop is enough, so we can drop the check for the dpll
compute callback, too.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
drm/i915: Don't store current shared DPLL in the new pipe_config
Now that shared DPLLs configuration is staged, there's no need to track
the current ones in the new pipe_config since those are released before
making the new pipe_config effective.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
projects / linux-beck.git / log