David S. Miller [Mon, 19 Jan 2015 19:44:33 +0000 (14:44 -0500)]
Merge branch 'link_netns'
Merge branch 'link_netns'
Nicolas Dichtel says:
====================
netns: allow to identify peer netns
The goal of this serie is to be able to multicast netlink messages with an
attribute that identify a peer netns.
This is needed by the userland to interpret some information contained in
netlink messages (like IFLA_LINK value, but also some other attributes in case
of x-netns netdevice (see also
http://thread.gmane.org/gmane.linux.network/315933/focus=316064 and
http://thread.gmane.org/gmane.linux.kernel.containers/28301/focus=4239)).
Ids of peer netns can be set by userland via a new rtnl cmd RTM_NEWNSID. When
the kernel needs an id for a peer (for example when advertising a new x-netns
interface via netlink), if the user didn't allocate an id, one will be
automatically allocated.
These ids are stored per netns and are local (ie only valid in the netns where
they are set). To avoid allocating an int for each peer netns, I use
idr_for_each() to retrieve the id of a peer netns. Note that it will be possible
to add a table (struct net -> id) later to optimize this lookup if needed.
Patch 1/4 introduces the rtnetlink API mechanism to set and get these ids.
Patch 2/4 and 3/4 implements an example of how to use these ids when advertising
information about a x-netns interface.
And patch 4/4 shows that the netlink messages can be symetric between a GET and
a SET.
iproute2 patches are available, I can send them on demand.
Here is a small screenshot to show how it can be used by userland.
$ ip netns add foo
$ ip netns del foo
$ ip netns
$ touch /var/run/netns/init_net
$ mount --bind /proc/1/ns/net /var/run/netns/init_net
$ ip netns add foo
$ ip -n foo netns
foo
init_net
$ ip -n foo netns set init_net 0
$ ip -n foo netns set foo 1
$ ip netns
foo
init_net
$ ip -n foo netns
foo (id: 1)
init_net (id: 0)
$ ip -n foo link add ipip1 link-netnsid 0 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
6: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0
$ ip netns
foo
init_net
$ ip -n foo link add ipip2 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link set ipip2 netns init_net
$ ip link ls ipip2
7: ipip2@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0
$ ip netns
foo (id: 0)
init_net
v4 -> v5:
use rtnetlink instead of genetlink
allocate automatically an id if user didn't assign one
rename include/uapi/linux/netns.h to include/uapi/linux/net_namespace.h
add vxlan in patch #3
RFCv3 -> v4:
rebase on net-next
add copyright text in the new netns.h file
RFCv2 -> RFCv3:
ids are now defined by userland (via netlink). Ids are stored in each netns
(and they are local to this netns).
add get_link_net support for ip6 tunnels
netnsid is now a s32 instead of a u32
RFCv1 -> RFCv2:
remove useless ()
ids are now stored in the user ns. It's possible to get an id for a peer netns
only if the current netns and the peer netns have the same user ns parent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 15 Jan 2015 14:11:18 +0000 (15:11 +0100)]
rtnl: allow to create device with IFLA_LINK_NETNSID set
This patch adds the ability to create a netdevice in a specified netns and
then move it into the final netns. In fact, it allows to have a symetry between
get and set rtnl messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 15 Jan 2015 14:11:16 +0000 (15:11 +0100)]
rtnl: add link netns id to interface messages
This patch adds a new attribute (IFLA_LINK_NETNSID) which contains the 'link'
netns id when this netns is different from the netns where the interface
stands (for example for x-net interfaces like ip tunnels).
With this attribute, it's possible to interpret correctly all advertised
information (like IFLA_LINK, etc.).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 15 Jan 2015 14:11:15 +0000 (15:11 +0100)]
netns: add rtnl cmd to add and get peer netns ids
With this patch, a user can define an id for a peer netns by providing a FD or a
PID. These ids are local to the netns where it is added (ie valid only into this
netns).
The main function (ie the one exported to other module), peernet2id(), allows to
get the id of a peer netns. If no id has been assigned by the user, this
function allocates one.
These ids will be used in netlink messages to point to a peer netns, for example
in case of a x-netns interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rosen, Rami [Mon, 19 Jan 2015 09:45:04 +0000 (11:45 +0200)]
bridge: remove oflags from setlink/dellink.
Commit 02dba4388d16 ("bridge: fix setlink/dellink notifications") removed usage of oflags in
both rtnl_bridge_setlink() and rtnl_bridge_dellink() methods. This patch removes this variable as it is no
longer needed.
Signed-off-by: Rami Rosen <rami.rosen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Jan 2015 04:36:08 +0000 (23:36 -0500)]
netlink: Fix bugs in nlmsg_end() conversions.
Commit 053c095a82cf ("netlink: make nlmsg_end() and genlmsg_end()
void") didn't catch all of the cases where callers were breaking out
on the return value being equal to zero, which they no longer should
when zero means success.
Fix all such cases.
Reported-by: Marcel Holtmann <marcel@holtmann.org> Reported-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Fri, 16 Jan 2015 18:11:00 +0000 (10:11 -0800)]
ip_tunnel: Create percpu gro_cell
In the ipip tunnel, the skb->queue_mapping is lost in ipip_rcv().
All skb will be queued to the same cell->napi_skbs. The
gro_cell_poll is pinned to one core under load. In production traffic,
we also see severe rx_dropped in the tunl iface and it is probably due to
this limit: skb_queue_len(&cell->napi_skbs) > netdev_max_backlog.
This patch is trying to alloc_percpu(struct gro_cell) and schedule
gro_cell_poll to process the skb in the same core.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rx / Tx errors tested by injecting faults in qemu's hardware model for Rocker.
v2:
- moved counter locations to avoid potential use after free per Florian's comment
Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Scott Feldman <sfeldma@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 16 Jan 2015 21:09:00 +0000 (22:09 +0100)]
netlink: make nlmsg_end() and genlmsg_end() void
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Alpe [Fri, 16 Jan 2015 11:30:40 +0000 (12:30 +0100)]
tipc: fix socket list regression in new nl api
Commit 07f6c4bc (tipc: convert tipc reference table to use generic
rhashtable) introduced a problem with port listing in the new netlink
API. It broke the resume functionality resulting in a never ending
loop. This was caused by starting with the first hash table every time
subsequently never returning an empty skb (terminating).
This patch fixes the resume mechanism by keeping a logical reference
to the last hash table along with a logical reference to the socket
(port) that didn't fit in the previous message.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some more bluetooth & ieee802154 patches intended for 3.20:
- Refactoring & cleanups of ieee802154 & 6lowpan code
- Various fixes to the btmrvl driver
- Fixes for Bluetooth Low Energy Privacy feature handling
- Added build-time sanity checks for sockaddr sizes
- Fixes for Security Manager registration on LE-only controllers
- Refactoring of broken inquiry mode handling to a generic quirk
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Jan 2015 22:49:37 +0000 (23:49 +0100)]
net: replace br_fdb_external_learn_* calls with switchdev notifier events
This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Jan 2015 22:49:36 +0000 (23:49 +0100)]
switchdev: introduce switchdev notifier
This patch introduces new notifier for purposes of exposing events which happen
on switch driver side. The consumers of the event messages are mainly involved
masters, namely bridge and ovs.
Suggested-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 16 Jan 2015 13:35:09 +0000 (14:35 +0100)]
socket: use ki_nbytes instead of iov_length()
This field already contains the length of the iovec, no need to calculate it
again.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Richter [Fri, 16 Jan 2015 13:05:49 +0000 (14:05 +0100)]
qeth: Remove unneeded structure member
The member irq_tasklet in the qeth_channel structure
is not referenced anymore and is removed from the
structure.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Fri, 16 Jan 2015 13:05:47 +0000 (14:05 +0100)]
qeth: use qeth_card_hw_is_reachable() everywhere
qeth_card_hw_is_reachable() was introduced as part of a new
functionality, but it is a useful abstraction that can replace
verbose checks througout the rest of the `qeth` driver.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Thomas-Mich Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Elfring [Fri, 16 Jan 2015 13:05:46 +0000 (14:05 +0100)]
s390/net: Delete useless checks before function calls
The function debug_unregister() tests whether its argument is
NULL and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Mahfouz [Fri, 16 Jan 2015 13:05:45 +0000 (14:05 +0100)]
s390/ctcm, netiucv: migrate variables to handle y2038 problem
This patch is concerned with migrating the time variables for the s390
network drivers. The changes handle the y2038 problem where timespec will
overflow in the year 2038. timespec was replaced by unsigned long and
all time variables get their values from the jiffies global variable.
This was done for the sake of speed and efficiency.
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Jan 2015 08:52:40 +0000 (09:52 +0100)]
tc: cls_bpf: rename bpf_len to bpf_num_ops
It was suggested by DaveM to change the name as "len" might indicate
unit bytes.
Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Thu, 15 Jan 2015 04:02:25 +0000 (20:02 -0800)]
bridge: fix setlink/dellink notifications
problems with bridge getlink/setlink notifications today:
- bridge setlink generates two notifications to userspace
- one from the bridge driver
- one from rtnetlink.c (rtnl_bridge_notify)
- dellink generates one notification from rtnetlink.c. Which
means bridge setlink and dellink notifications are not
consistent
- Looking at the code it appears,
If both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF were set,
the size calculation in rtnl_bridge_notify can be wrong.
Example: if you set both BRIDGE_FLAGS_MASTER and BRIDGE_FLAGS_SELF
in a setlink request to rocker dev, rtnl_bridge_notify will
allocate skb for one set of bridge attributes, but,
both the bridge driver and rocker dev will try to add
attributes resulting in twice the number of attributes
being added to the skb. (rocker dev calls ndo_dflt_bridge_getlink)
There are multiple options:
1) Generate one notification including all attributes from master and self:
But, I don't think it will work, because both master and self may use
the same attributes/policy. Cannot pack the same set of attributes in a
single notification from both master and slave (duplicate attributes).
2) Generate one notification from master and the other notification from
self (This seems to be ideal):
For master: the master driver will send notification (bridge in this
example)
For self: the self driver will send notification (rocker in the above
example. It can use helpers from rtnetlink.c to do so. Like the
ndo_dflt_bridge_getlink api).
This patch implements 2) (leaving the 'rtnl_bridge_notify' around to be used
with 'self').
v1->v2 :
- rtnl_bridge_notify is now called only for self,
so, remove 'BRIDGE_FLAGS_SELF' check and cleanup a few things
- rtnl_bridge_dellink used to always send a RTM_NEWLINK msg
earlier. So, I have changed the notification from br_dellink to
go as RTM_NEWLINK
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 18 Jan 2015 01:34:14 +0000 (20:34 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-01-16
This series contains updates to i40e and i40evf.
This series is a little bit larger than normal because two of the patches are
version bumps.
Shannon provides tweaks to i40e and i40evf to keep the firmware, software
and silicon validation in line together by removing unused and
deprecated code, adding define for iSCSI and fix queue mask size. Fix
i40e so we do not give up in the reset/rebuild process if DCB setup
fails, just handle it the same as in the probe setup. Cleans up PTP
log messages by removing the use of __func__ as we are not using that
any longer and removes the netdev name, since that can change and can
be misleading. Adds struct size checks to indirect and command
structs that were left out previously. Added admin queue API updates
(LLDP control, OEM OCSD and OCBB commands).
Kevin increases ASQ timeout for scenarios with multi-function devices.
Carolyn fixes a problem where the interrupts descriptions from the MSIx
configuration were truncating the needed bus info, which makes it hard
to distinguish configurations from port to port. Increased the string
buffer size in order to allow the full data to be displayed.
Sravanthi cleans up the dump stats string from debugfs.
Jacob updates i40e to only enable the PTP interrupt in PFs which have PTP
enabled, instead of blindly enabling the PTP interrupt flags for all PFs.
Also updated i40e so that we do not do Tx or Rx timestamps if we do not
have PTP enabled. Added the same check against pf->ptp_rx as we have
in Rx timestamp code path because it is possible that the user can
configure only Tx hardware timestamping so we do not want to check for
Rx timestamp hang since the software won't be handling them.
Neerav updates the driver to disable firmware LLDP agent for NICs with
a firmware version lower than v4.3 and added a message when this happens.
Adds parsing and reporting of iSCSI capability for a given device or
function, as well as adding support for iSCSI partition type with DCB
in NPAR mode.
v2:
- Dropped patch 10 "i40e: clean up PTP log messages" based on feedback
from David Laight and David Miller
- Split up the original patch 13 "i40e: AQ API updates for new commands"
into 2 patches (now #12 & #13) based on feedback from Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches includes functional updates to the
driver as well as some trivial changes.
- Fix checks/warnings from checkpatch in the amd-xgbe driver
- Fix checks/warnings from checkpatch in the amd-xgbe-phy driver
- Add a check to be sure that the amd-xgbe driver is using the
amd-xgbe-phy driver
- Use a saved control register value when bringing the PCS out of
suspend
- Clear all device state during a device restart
- Simplify the Rx descriptor ring tracking
- Remove the need for Tx path spinlocks
- Update the auto-negotiation logic to make use of the auto-negotiation
interrupt
- Properly support/advertise the FEC capability of the device
- Use the proper page registers during auto-negotiation extended next
page exchange
- Add ACPI support to the amd-xgbe and amd-xgbe-phy drivers
- Allow platform specific phy settings to be supplied by UEFI
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:47:21 +0000 (12:47 -0600)]
amd-xgbe-phy: Allow certain PHY settings to be set by UEFI
Certain PHY settings need to be configurable by UEFI depending on the
platform being used. Add new device tree / ACPI properties that, if
present, will override the pre-determined values currently used.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:47:10 +0000 (12:47 -0600)]
amd-xgbe-phy: Use the proper auto-negotiation XNP registers
When receiving and processing extended next pages the base registers
were used instead of the XNP registers. Update the code to use the
device XNP and link partner XNP registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:47:05 +0000 (12:47 -0600)]
amd-xgbe-phy: Properly support the FEC auto-negotiation
Advertise and apply the Forward Error Correction capabilities of the
device based on the FEC ability of the device. Also, remove the use
of some hard coded values related to KR and FEC in preference of some
#defines.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:47:00 +0000 (12:47 -0600)]
amd-xgbe-phy: Change auto-negotiation logic
The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:46:55 +0000 (12:46 -0600)]
amd-xgbe: Remove need for Tx path spinlock
Since the Tx ring cleanup can run at the same time that data is being
transmitted, a spin lock was used to protect the ring. This patch
eliminates the need for Tx spinlocks by updating the current ring
position only after all ownership bits for data being transmitted have
been set. This will insure that ring operations in the Tx cleanup path
do not interfere with the ring operations in the Tx transmit path.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:46:50 +0000 (12:46 -0600)]
amd-xgbe: Simplify the Rx desciptor ring tracking
Make the Rx descriptor ring processing similar to the Tx descriptor
ring processing. Remove the realloc_index and realloc_threshold
variables and base everything on the current index counter and the
dirty index counter.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:46:45 +0000 (12:46 -0600)]
amd-xgbe: Clear all state during a device restart
When performing a device restart, like during an MTU change, sometimes
the device queues still have data and get hung up trying to flush
resulting in the device becoming unresponsive until brought down and
back up. To prevent this, always perform a device reset during a
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:46:39 +0000 (12:46 -0600)]
amd-xgbe-phy: On suspend, save CTRL1 reg for use on resume
Reads to registers are undefined when the PCS is powered down. To be
safe, save the CTRL1 register used for power down during suspend and
restore that value during resume.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Fri, 16 Jan 2015 18:46:34 +0000 (12:46 -0600)]
amd-xgbe: Add check to be sure amd-xgbe-phy driver is used
The amd-xgbe driver relies on the amd-xgbe-phy phylib driver. Add a
check to be sure that if any errors occur during probing of the
amd-xgbe-phy driver then the amd-xgbe driver returns an error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32 Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Sun, 14 Dec 2014 01:55:16 +0000 (01:55 +0000)]
i40e: Support for NPAR iSCSI partition with DCB
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sun, 14 Dec 2014 01:55:15 +0000 (01:55 +0000)]
i40e: when Rx timestamps disabled set specific mode
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sun, 14 Dec 2014 01:55:14 +0000 (01:55 +0000)]
i40e: use same check for Rx hang as for Rx timestamps
It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.
Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Sun, 14 Dec 2014 01:55:12 +0000 (01:55 +0000)]
i40e: add more struct size checks
Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sun, 14 Dec 2014 01:55:09 +0000 (01:55 +0000)]
i40e: check I40E_FLAG_PTP before handling Tx or Rx timestamps
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sun, 14 Dec 2014 01:55:08 +0000 (01:55 +0000)]
i40e: only enable PTP interrupt cause if PTP is enabled
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 11 Dec 2014 07:06:38 +0000 (07:06 +0000)]
i40e: don't give up on DCB error after reset
We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup. Also adjust the log strings
a little to look less scary.
Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Thu, 11 Dec 2014 07:06:37 +0000 (07:06 +0000)]
i40e: fix proc/int descriptions
This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names
Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kevin Scott [Thu, 11 Dec 2014 07:06:36 +0000 (07:06 +0000)]
i40e/i40evf: Increase ASQ timeout
Increase ASQ timeout for some scenarios with multi-function devices
Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 12 Dec 2014 07:50:07 +0000 (07:50 +0000)]
i40e/i40evf: AdminQ updates ww36
Several little tweaks to keep FW, SV, and SW in line together
- Remove the unused and deprecated
i40e_aqc_opc_debug_modify_internals
- Add define for iSCSI capability
- Fix queue mask size
- Adjust i40e_aqc_oem_param_change for ease-of-use
Change-ID: I51f250b367912968a7cec61b3a68110d9796e914 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Herbert Xu [Fri, 16 Jan 2015 06:23:48 +0000 (17:23 +1100)]
netlink: Fix netlink_insert EADDRINUSE error
The patch c5adde9468b0714a051eac7f9666f23eb10b61f7 ("netlink:
eliminate nl_sk_hash_lock") introduced a bug where the EADDRINUSE
error has been replaced by ENOMEM. This patch rectifies that
problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Fri, 16 Jan 2015 03:13:09 +0000 (11:13 +0800)]
rhashtable: Fix race in rhashtable_destroy() and use regular work_struct
When we put our declared work task in the global workqueue with
schedule_delayed_work(), its delay parameter is always zero.
Therefore, we should define a regular work in rhashtable structure
instead of a delayed work.
By the way, we add a condition to check whether resizing functions
are NULL before cancelling the work, avoiding to cancel an
uninitialized work.
Lastly, while we wait for all work items we submitted before to run
to completion with cancel_delayed_work(), ht->mutex has been taken in
rhashtable_destroy(). Moreover, cancel_delayed_work() doesn't return
until all work items are accomplished, and when work items are
scheduled, the work's function - rht_deferred_worker() will be called.
However, as rht_deferred_worker() also needs to acquire the lock,
deadlock might happen at the moment as the lock is already held before.
So if the cancel work function is moved out of the lock covered scope,
this will avoid the deadlock.
Fixes: 97defe1 ("rhashtable: Per bucket locks & deferred expansion/shrinking") Signed-off-by: Ying Xue <ying.xue@windriver.com> Cc: Thomas Graf <tgraf@suug.ch> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Jan 2015 06:07:02 +0000 (01:07 -0500)]
Merge branch 'iw_cxgb4-next'
Hariprasad Shenai says:
====================
Refactor macros to conform to uniform standards
This patch series cleansup macros/register defines, defined in t4.h and
t4fw_ri_api.h and all the affected files.
This patch series is created against net-next tree and includes patches on
iw_cxgb4 tree. Since the patches are dependent on previous cleanup patched we
would line to get this series merged through net-next tree.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xander Huff [Thu, 15 Jan 2015 21:55:20 +0000 (15:55 -0600)]
net/macb: Create gem_ethtool_ops for new statistics functions
10/100 MACB does not have the same statistics possibilities as GEM. Separate
macb_ethtool_ops to make a new GEM-specific struct with the new statistics
functions included.
Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gao Zhenyu <gzhenyu@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Schmitz [Thu, 15 Jan 2015 13:06:15 +0000 (14:06 +0100)]
net: smc91x: Add Atari EtherNAT support
Add Atari specific code to the smc91x Ethernet driver. This code is used
on the EtherNAT adapter card for the Atari Falcon extension port.
Signed-off-by: Michael Schmitz <schmitz@debian.org> Tested-by: Christian Steigies <cts@debian.org>
[geert: Sort Kconfig entries, split in hard and soft dependencies] Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Jan 2015 00:16:56 +0000 (19:16 -0500)]
Merge tag 'mac80211-next-for-davem-2015-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Here's a big pile of changes for this round.
We have
* a lot of regulatory code changes to deal with the
way newer Intel devices handle this
* a change to drop packets while disconnecting from
an AP instead of trying to wait for them
* a new attempt at improving the tailroom accounting
to not kick in too much for performance reasons
* improvements in wireless link statistics
* many other small improvements and small fixes that
didn't seem necessary for 3.19 (e.g. in hwsim which
is testing only code)
Anish Bhatt [Wed, 14 Jan 2015 23:17:34 +0000 (15:17 -0800)]
cxgb4 : Update ipv6 address handling api
This patch improves on previously added support for ipv6 addresses. The code
is consolidated to a single file and adds an api for use by dependent upper
level drivers such as cxgb4i/iw_cxgb4 etc.
Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: Deepak Singh <deepak.s@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 14 Jan 2015 23:17:06 +0000 (15:17 -0800)]
ipv4: per cpu uncached list
RAW sockets with hdrinc suffer from contention on rt_uncached_lock
spinlock.
One solution is to use percpu lists, since most routes are destroyed
by the cpu that created them.
It is unclear why we even have to put these routes in uncached_list,
as all outgoing packets should be freed when a device is dismantled.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: caacf05e5ad1 ("ipv4: Properly purge netdev references on uncached routes.") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Thu, 15 Jan 2015 16:04:21 +0000 (08:04 -0800)]
Bluetooth: Add paranoid check for existing LE and BR/EDR SMP channels
When the SMP channels have been already registered, then print out a
clear WARN_ON message that something went wrong. Also unregister the
existing channels in this case before trying to register new ones.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In boards, the dm9000 chip's power and reset can be controlled by gpio.
It makes sense to add them to the dm9000 driver and let dt be used to
enable power and reset the phy.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg [Thu, 15 Jan 2015 11:06:45 +0000 (13:06 +0200)]
Bluetooth: Fix lookup of fixed channels by local bdaddr
The comparing of chan->src should always be done against the local
identity address, represented by hcon->src and hcon->src_type. This
patch modifies l2cap_global_fixed_chan() to take the full hci_conn so
that we can easily compare against hcon->src and hcon->src_type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 15 Jan 2015 11:06:44 +0000 (13:06 +0200)]
Bluetooth: Add helpers for src/dst bdaddr type conversion
The current bdaddr_type() usage in l2cap_core.c is a bit funny in that
it's always passed a hci_conn + a hci_conn member. Because of this only
the hci_conn is really needed. Since the second parameter is always
either hcon->src_type or hcon->dst type this patch adds two helper
functions for each purpose: bdaddr_src_type() and bdaddr_dst_type().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 14 Jan 2015 23:43:11 +0000 (15:43 -0800)]
Bluetooth: Bind the SMP channel registration to management power state
When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.
When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.
In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 14 Jan 2015 23:43:09 +0000 (15:43 -0800)]
Bluetooth: Fix LE SMP channel source address and source address type
The source address and source address type of the LE SMP channel can
either be the public address of the controller or the static random
address configured by the host.
Right now the public address is used for the LE SMP channel and
obviously that is not correct if the controller operates with the
configured static random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 14 Jan 2015 22:40:42 +0000 (14:40 -0800)]
Bluetooth: Fix issue with switching BR/EDR back on when disabled
For dual-mode controllers it is possible to disable BR/EDR and operate
as LE single mode controllers with a static random address. If that is
the case, then refuse switching BR/EDR back on after the controller has
been powered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 14 Jan 2015 21:44:21 +0000 (13:44 -0800)]
Bluetooth: Show device address type for L2CAP debugfs entries
The devices address types are BR/EDR Public, LE Public and LE Random and
any of these three is valid for L2CAP connections. So show the correct
type in the debugfs list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
====================
netfilter updates for net-next
The following patchset contains netfilter updates for net-next, just a
bunch of cleanups and small enhancement to selectively flush conntracks
in ctnetlink, more specifically the patches are:
1) Rise default number of buckets in conntrack from 16384 to 65536 in
systems with >= 4GBytes, patch from Marcelo Leitner.
2) Small refactor to save one level on indentation in xt_osf, from
Joe Perches.
3) Remove unnecessary sizeof(char) in nf_log, from Fabian Frederick.
4) Another small cleanup to remove redundant variable in nfnetlink,
from Duan Jiong.
5) Fix compilation warning in nfnetlink_cthelper on parisc, from
Chen Gang.
6) Fix wrong format in debugging for ctseqadj, from Gao feng.
7) Selective conntrack flushing through the mark for ctnetlink, patch
from Kristian Evensen.
8) Remove nf_ct_conntrack_flush_report() exported symbol now that is
not required anymore after the selective flushing patch, again from
Kristian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Jan 2015 06:12:13 +0000 (01:12 -0500)]
Merge branch 'vxlan_group_policy_extension'
Thomas Graf says:
====================
VXLAN Group Policy Extension
Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.
The extension is disabled by default and should be run on a distinct
port in mixed Linux VXLAN VTEP environments. Liberal VXLAN VTEPs
which ignore unknown reserved bits will be able to receive VXLAN-GBP
frames.
Simple usage example:
10.1.1.1:
# ip link add vxlan0 type vxlan id 10 remote 10.1.1.2 gbp
# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
10.1.1.2:
# ip link add vxlan0 type vxlan id 10 remote 10.1.1.1 gbp
# iptables -I INPUT -m mark --mark 0x200 -j DROP
iproute2 [1] and OVS [2] support will be provided in separate patches.
Thomas Graf [Thu, 15 Jan 2015 02:53:59 +0000 (03:53 +0100)]
openvswitch: Support VXLAN Group Policy extension
Introduces support for the group policy extension to the VXLAN virtual
port. The extension is disabled by default and only enabled if the user
has provided the respective configuration.
The configuration interface to enable the extension is based on a new
attribute OVS_VXLAN_EXT_GBP nested inside OVS_TUNNEL_ATTR_EXTENSION
which can carry additional extensions as needed in the future.
The group policy metadata is stored as binary blob (struct ovs_vxlan_opts)
internally just like Geneve options but transported as nested Netlink
attributes to user space.
Renames the existing TUNNEL_OPTIONS_PRESENT to TUNNEL_GENEVE_OPT with the
binary value kept intact, a new flag TUNNEL_VXLAN_OPT is introduced.
The attributes OVS_TUNNEL_KEY_ATTR_VXLAN_OPTS and existing
OVS_TUNNEL_KEY_ATTR_GENEVE_OPTS are implemented mutually exclusive.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 15 Jan 2015 02:53:58 +0000 (03:53 +0100)]
openvswitch: Allow for any level of nesting in flow attributes
nlattr_set() is currently hardcoded to two levels of nesting. This change
introduces struct ovs_len_tbl to define minimal length requirements plus
next level nesting tables to traverse the key attributes to arbitrary depth.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 15 Jan 2015 02:53:57 +0000 (03:53 +0100)]
openvswitch: Rename GENEVE_TUN_OPTS() to TUN_METADATA_OPTS()
Also factors out Geneve validation code into a new separate function
validate_and_copy_geneve_opts().
A subsequent patch will introduce VXLAN options. Rename the existing
GENEVE_TUN_OPTS() to reflect its extended purpose of carrying generic
tunnel metadata options.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 15 Jan 2015 02:53:56 +0000 (03:53 +0100)]
vxlan: Only bind to sockets with compatible flags enabled
A VXLAN net_device looking for an appropriate socket may only consider
a socket which has a matching set of flags/extensions enabled. If
incompatible flags are enabled, return a conflict to have the caller
create a distinct socket with distinct port.
The OVS VXLAN port is kept unaware of extensions at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Thu, 15 Jan 2015 02:53:55 +0000 (03:53 +0100)]
vxlan: Group Policy extension
Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.
The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.
SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels. However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.
Host 1: Host 2:
Group A Group B Group B Group A
+-----+ +-------------+ +-------+ +-----+
| lxc | | SELinux CTX | | httpd | | VM |
+--+--+ +--+----------+ +---+---+ +--+--+
\---+---/ \----+---/
| |
+---+---+ +---+---+
| vxlan | | vxlan |
+---+---+ +---+---+
+------------------------------+
Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP frames. The extension is therefore disabled by default
and needs to be specifically enabled:
ip link add [...] type vxlan [...] gbp
In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.
Examples:
iptables:
host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
host2# iptables -I INPUT -m mark --mark 0x200 -j DROP
1) Don't use uninitialized data in IPVS, from Dan Carpenter.
2) conntrack race fixes from Pablo Neira Ayuso.
3) Fix TX hangs with i40e, from Jesse Brandeburg.
4) Fix budget return from poll calls in dnet and alx, from Eric
Dumazet.
5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
Jaeger.
6) Fix bug introduced by conversion to list_head in TIPC retransmit
code, from Jon Paul Maloy.
7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
Khoroshilov.
8) Fix bridge build with INET disabled, from Arnd Bergmann.
9) Fix netlink array overrun for PROBE attributes in openvswitch, from
Thomas Graf.
10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
Prashant Sreedharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
tg3: Release tp->lock before invoking synchronize_irq()
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
openvswitch: packet messages need their own probe attribtue
i40e: adds FCoE configure option
cxgb4vf: Fix queue allocation for 40G adapter
netdevice: Add missing parentheses in macro
bridge: only provide proxy ARP when CONFIG_INET is enabled
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
net: fec: fix MDIO bus assignement for dual fec SoC's
xen-netfront: use different locks for Rx and Tx stats
drivers: net: cpsw: fix multicast flush in dual emac mode
cxgb4vf: Initialize mdio_addr before using it
net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
MAINTAINERS: add me as ibmveth maintainer
tipc: fix bug in broadcast retransmit code
update ip-sysctl.txt documentation (v2)
net/at91_ether: prepare and unprepare clock
...
projects / linux-beck.git / log