Enable partial low interrupt latency mode for ARM1136
Enable partial low interrupt latency mode for ARM1136
This patch is a workaround for the 364296 ARM1136 r0pX errata
(possible cache data corruption with hit-under-miss enabled). It sets
the undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Jason Liu [Wed, 26 Mar 2008 02:57:06 +0000 (21:57 -0500)]
ENGR00069937 Community patch for Fix mount error in case of MLC flash
Even though we don't use the OOB for MLC nand flash,
we should use the bad block information to skip the bad block.
Patch url:
http://patchwork.ozlabs.org/linux-mtd/patch?q=mlc&filter=none&id=15477
Author:Kyungmin Park
Read esd_csd info each time when cat boot_info
becasue user may change config affect esd_csd
value.
boot_info:0x07;
ALT_BOOT_MODE:1 - Supports alternate boot method
DDR_BOOT_MODE:1 - Supports alternate dual data rate during boot
HS_BOOTMODE:1 - Supports high speed timing during boot
boot_size:0512KB
boot_partition:0x48;
BOOT_ACK:1 - Boot acknowledge sent during boot operation
BOOT_PARTITION-ENABLE: 1 - Boot partition 1 enabled
PARTITION_ACCESS:0 - No access to boot partition
boot_bus:0x01
BOOT_MODE:0 - Use single data rate + backward compatible timings
in boot operation
RESET_BOOT_BUS_WIDTH:0 - Reset bus width to x1, single data rate
and backward compatible timings after boot operation
BOOT_BUS_WIDTH:1 - x4 (sdr/ddr) bus width in boot operation mode
Enable the configurations of the boot enable on the eMMC cards.
Add the interface that used to configure the boot_bus_width
In order to make sure that the re-read the ext-csd of card
can be completed successfully, add the method to wait for
the finish of the busy state.
NOTE:
The following are the valid inputs when configure the boot
bus width of the eMMC cards.
+--------------------------------------------------------------------+
| Bit7 Bit6 Bit5 | Bit4 Bit3 | Bit2 | Bit1 Bit0 |
|----------------|----------------------------------|----------------|
| X | BOOT_MODE | RESET_BOOT_BUS_WIDTH | BOOT_BUS_WIDTH |
+--------------------------------------------------------------------+
Bit [4:3] : BOOT_MODE (non-volatile)
0x0 : Use single data rate + backward compatible timings in boot
operation (default)
0x1 : Use single data rate + high speed timings in boot operation mode
0x2 : Use dual data rate in boot operation
0x3 : Reserved
Bit [2]: RESET_BOOT_BUS_WIDTH (non-volatile)
0x0 : Reset bus width to x1, single data rate and backward compatible
timings after boot operation (default)
0x1 : Retain boot bus width and boot mode after boot operation
Bit[1:0] : BOOT_BUS_WIDTH (non-volatile)
0x0 : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
0x1 : x4 (sdr/ddr) bus width in boot operation mode
0x2 : x8 (sdr/ddr) bus width in boot operation mode
0x3 : Reserved
The following are the valid inputs when configure the boot
partitions of the eMMC cards.
+------------------------------------------------------------+
| Bit7 | Bit6 | Bit5 Bit4 Bit3 | Bit2 Bit1 Bit0 |
|------|----------|-----------------------|------------------|
| X | BOOT_ACK | BOOT_PARTITION_ENABLE | PARTITION_ACCESS |
+------------------------------------------------------------+
Bit7: Reserved
Bit6: always set to vaule '1' when boot_part is enabled
Bit[5:3]:
0x0 : Device not boot enabled (default)
0x1 : Boot partition 1 enabled for boot
0x2 : Boot partition 2 enabled for boot
0x7 : User area enabled for boot
Bit[2:0]:
0x0 : No access to boot partition (default)
0x1 : R/W boot partition 1
0x2 : R/W boot partition 2
So only the '0, 1, 2; 8, 9, 10; 16, 17, 18; 56, 57, 58' are
valid parameters when configure the boot_partiton.
Richard Zhu [Fri, 23 Jul 2010 08:38:06 +0000 (16:38 +0800)]
ENGR00125411 eMMC: Boot Partition switch func used in MFG tool
User can get eMMC partitions info from user space layer in
linux OS enviroment.
User can do switch operations between the eMMC boot partitions
and the user partition.
User can access the eMMC boot partitions from user space layer
in linux OS enviroment.
NOTE:This func had been verified on TOSHIBA eMMC44 card only.
Signed-off-by: Richard Zhu <r65037@freescale.com> Signed-off-by: Rob Herring <r.herring@freescale.com>
When called for anonymous (non-shared) mappings, hugetlb_reserve_pages()
does a resv_map_alloc(). It depends on code in hugetlbfs's
vm_ops->close() to release that allocation.
However, in the mmap() failure path, we do a plain unmap_region() without
the remove_vma() which actually calls vm_ops->close().
This is a decent fix. This leak could get reintroduced if new code (say,
after hugetlb_reserve_pages() in hugetlbfs_file_mmap()) decides to return
an error. But, I think it would have to unroll the reservation anyway.
The transfer of ->flags causes some of the static mapping virtual
addresses to be prematurely freed (before the mapping is removed) because
VM_LAZY_FREE gets "set" if tmp->flags has VM_IOREMAP set. This might
cause subsequent vmalloc/ioremap calls to fail because it might allocate
one of the freed virtual address ranges that aren't unmapped.
va->flags has different types of flags from tmp->flags. If a region with
VM_IOREMAP set is registered with vm_area_add_early(), it will be removed
by __purge_vmap_area_lazy().
Fix vmalloc_init() to correctly initialize vmap_area for the given
vm_struct.
Also initialise va->vm. If it is not set, find_vm_area() for the early
vm regions will always fail.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com> Cc: "Olav Haugan" <ohaugan@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmap_area->private is void* but we don't use the field for various purpose
but use only for vm_struct. So change it to a vm_struct* with naming to
improve for readability and type checking.
Signed-off-by: Minchan Kim <minchan@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Virtual Machines with emulated e1000 network adapter running on Parallels'
server were seeing kernel panics due to the e1000 driver dereferencing an
unexpected NULL pointer retrieved from buffer_info->skb.
The problem has been addressed for the e1000e driver, but not for the e1000.
Since the two drivers share similar code in the affected area, a port of the
following e1000e driver commit solves the issue for the e1000 driver:
e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Dean Nelson <dnelson@redhat.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Roman Kagan <rkagan@parallels.com>
Now we store attr->ino at inode->i_ino, return attr->ino at the
first time and then return inode->i_ino if the attribute timeout
isn't expired. That's wrong on 32 bit platforms because attr->ino
is 64 bit and inode->i_ino is 32 bit in this case.
Fix this by saving 64 bit ino in fuse_inode structure and returning
it every time we call getattr. Also squash attr->ino into inode->i_ino
explicitly.
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: Robert Richter <robert.richter@amd.com>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:
Queue 2 stuck for 10000ms
This doesn't seem to fix the higher queues that get stuck
from time to time.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It does not get processed because sched_domain_level_max is 0 at the
time that setup_relax_domain_level() is run.
Simply accept the value as it is, as we don't know the value of
sched_domain_level_max until sched domain construction is completed.
Fix sched_relax_domain_level in cpuset. The build_sched_domain() routine calls
the set_domain_attribute() routine prior to setting the sd->level, however,
the set_domain_attribute() routine relies on the sd->level to decide whether
idle load balancing will be off/on.
Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On high CPU load the accumulating values in the running_avg_cap
register are very low (below 10), so averaging them too early leads
to unnecessary poor output resolution. Since we pretend to output
micro-Watt we better keep all the bits we have as long as possible.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an interrupt thrash issue with c_can driver.
In c_can_isr() function interrupts are disabled and enabled only in
c_can_poll() function. c_can_isr() & c_can_poll() both read the
irqstatus flag. However, irqstatus is always read as 0 in c_can_poll()
because all C_CAN interrupts are disabled in c_can_isr(). This causes
all interrupts to be re-enabled in c_can_poll() which in turn causes
another interrupt since the event is not really handled. This keeps
happening causing a flood of interrupts.
To fix this, read the irqstatus register in isr and use the same cached
value in the poll function.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue with transmit routine, which causes
"can_put_echo_skb: BUG! echo_skb is occupied!" message when
using "cansequence -p" on D_CAN controller.
In c_can driver, while transmitting packets tx_echo flag holds
the no of can frames put for transmission into the hardware.
As the comment above c_can_do_tx() indicates, if we find any packet
which is not transmitted then we should stop looking for more.
In the current implementation this is not taken care of causing the
said message.
Also, fix the condition used to find if the packet is transmitted
or not. Current code skips the first tx message object and ends up
checking one extra invalid object.
While at it, fix the comment on top of c_can_do_tx() to use the
terminology "packet" instead of "package" since it is more
standard.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 32 bit variant of cbc(aes) decrypt is using instructions requiring
128 bit aligned memory locations but fails to ensure this constraint in
the code. Fix this by loading the data into intermediate registers with
load unaligned instructions.
This fixes reported general protection faults related to aesni.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43223 Reported-by: Daniel <garkein@mailueberfall.de> Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description] Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory the parameter __key points to is used as an iterator in
btree_get_prev(), so if we save off a bkey() pointer in retry_key and
then assign that to __key, we'll end up corrupting the btree internals
when we do eg
longcpy(__key, bkey(geo, node, i), geo->keylen);
to return the key value. What we should do instead is use longcpy() to
copy the key value that retry_key points to __key.
This can cause a btree to get corrupted by seemingly read-only
operations such as btree_for_each_safe.
[akpm@linux-foundation.org: avoid the double longcpy()] Signed-off-by: Roland Dreier <roland@purestorage.com> Acked-by: Joern Engel <joern@logfs.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7990696 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags. So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to regenerate the sysfs files when the capacity units
change, avoid the update otherwise.
The origin of this issue is dates way back to 2.6.38: da8aeb92d4853f37e281f11fddf61f9c7d84c3cd
(ACPI / Battery: Update information on info notification and resume)
Signed-off-by: Andy Whitcroft <apw@canonical.com> Tested-by: Ralf Jung <post@ralfj.de> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't have references held on pages in the s_buddy_cache while we are
trying to truncate its pages and put the inode. All the pages must be
gone before we reach clear_inode. This can only be gauranteed if we
can prevent new users from grabbing references to s_buddy_cache's pages.
The original bug can be reproduced and the bug fix can be verified by:
while true; do mount -t ext4 /dev/ram0 /export/hda3/ram0; \
umount /export/hda3/ram0; done &
while true; do cat /proc/fs/ext4/ram0/mb_groups; done
In commit 353eb83c we removed i_state_flags with 64-bit longs, But
when handling the EXT4_IOC_SETFLAGS ioctl, we replace i_flags
directly, which trashes the state flags which are stored in the high
32-bits of i_flags on 64-bit platforms. So use the the
ext4_{set,clear}_inode_flags() functions which use atomic bit
manipulation functions instead.
Reported-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ext4_error() function is missing a call to save_error_info().
Since this is the function which marks the file system as containing
an error, this oversight (which was introduced in 2.6.36) is quite
significant, and should be backported to older stable kernels with
high urgency.
Corrects the function that determines the esp payload size. The calculations
done in esp{4,6}_get_mtu() lead to overlength frames in transport mode for
certain mtu values and suboptimal frames for others.
According to what is done, mainly in esp{,6}_output() and tcp_mtu_to_mss(),
net_header_len must be taken into account before doing the alignment
calculation.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the beginning of __skb_cow, headroom gets set to a minimum of
NET_SKB_PAD. This causes unnecessary reallocations if the buffer was not
cloned and the headroom is just below NET_SKB_PAD, but still more than the
amount requested by the caller.
This was showing up frequently in my tests on VLAN tx, where
vlan_insert_tag calls skb_cow_head(skb, VLAN_HLEN).
Locally generated packets should have enough headroom, and for forward
paths, we already have NET_SKB_PAD bytes of headroom, so we don't need to
add any extra space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Vlad Yaseivch <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
commit c57b5468406 (pktgen: fix crash at module unload) did a very poor
job with list primitives.
1) list_splice() arguments were in the wrong order
2) list_splice(list, head) has undefined behavior if head is not
initialized.
3) We should use the list_splice_init() variant to clear pktgen_threads
list.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hold the pktgen_thread_lock while splicing pktgen_threads, and test
pktgen_exiting in pktgen_device_event() to make unload faster.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An application may call connect() to disconnect a socket using an
address with family AF_UNSPEC. The L2TP IP sockets were not handling
this case when the socket is not bound and an attempt to connect()
using AF_UNSPEC in such cases would result in an oops. This patch
addresses the problem by protecting the sk_prot->disconnect() call
against trying to unhash the socket before it is bound.
The patch also adds more checks that the sockaddr supplied to bind()
and connect() calls is valid.
Since commit ad0081e43a
"ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed"
the fragment of packets is incorrect.
because tunnel mode needs IPsec headers and trailer for all fragments,
while on transport mode it is sufficient to add the headers to the
first fragment and the trailer to the last.
so modify mtu and maxfraglen base on ipsec mode and if fragment is first
or last.
with my test,it work well(every fragment's size is the mtu)
and does not trigger slow fragment path.
Changes from v1:
though optimization, mtu_prev and maxfraglen_prev can be delete.
replace xfrm mode codes with dst_entry's new frag DST_XFRM_TUNNEL.
add fuction ip6_append_data_mtu to make codes clearer.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
<3>[23898.789643] BUG: sleeping function called from invalid context at
/data/buildbot/workdir/ics/hardware/intel/linux-2.6/arch/x86/mm/fault.c:1103
<3>[23898.862215] in_atomic(): 0, irqs_disabled(): 0, pid: 10526, name:
Thread-6683
<4>[23898.967805] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.258526] Pid: 10526, comm: Thread-6683 Tainted: G W 3.0.8-137685-ge7742f9 #1
<4>[23899.357404] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.904225] Call Trace:
<4>[23899.989209] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.000416] [<c1238c2a>] __might_sleep+0x10a/0x110
<4>[23900.007357] [<c1228021>] do_page_fault+0xd1/0x3c0
<4>[23900.013764] [<c18e9ba9>] ? restore_all+0xf/0xf
<4>[23900.024024] [<c17c007b>] ? napi_complete+0x8b/0x690
<4>[23900.029297] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.123739] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.128955] [<c18ea0c3>] error_code+0x5f/0x64
<4>[23900.133466] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.138450] [<c17f6298>] ? __ip_route_output_key+0x698/0x7c0
<4>[23900.144312] [<c17f5f8d>] ? __ip_route_output_key+0x38d/0x7c0
<4>[23900.150730] [<c17f63df>] ip_route_output_flow+0x1f/0x60
<4>[23900.156261] [<c181de58>] ip4_datagram_connect+0x188/0x2b0
<4>[23900.161960] [<c18e981f>] ? _raw_spin_unlock_bh+0x1f/0x30
<4>[23900.167834] [<c18298d6>] inet_dgram_connect+0x36/0x80
<4>[23900.173224] [<c14f9e88>] ? _copy_from_user+0x48/0x140
<4>[23900.178817] [<c17ab9da>] sys_connect+0x9a/0xd0
<4>[23900.183538] [<c132e93c>] ? alloc_file+0xdc/0x240
<4>[23900.189111] [<c123925d>] ? sub_preempt_count+0x3d/0x50
Function free_fib_info resets nexthop_nh->nh_dev to NULL before releasing
fi. Other cpu might be accessing fi. Fixing it by delaying the releasing.
With the patch, we ran MTBF testing on Android mobile for 12 hours
and didn't trigger the issue.
Thank Eric for very detailed review/checking the issue.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com> Signed-off-by: Kun Jiang <kunx.jiang@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this bit sets we get broken rendering and
lockups.
fglrx sets this bit.
Bugs that should be fixed by this patch :
https://bugs.freedesktop.org/show_bug.cgi?id=49792
https://bugzilla.kernel.org/show_bug.cgi?id=43207
https://bugs.freedesktop.org/show_bug.cgi?id=39282
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to program an additional VM register. This doesn't not currently
cause any problems, but allows us to program the proper backend
map in a subsequent patch which should improve performance on these
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__mnt_make_shortterm() in there undoes the effect of __mnt_make_longterm()
we'd done back when we set ->mnt_ns non-NULL; it should not be done to
vfsmounts that had never gone through commit_tree() and friends. Kudos to
lczerner for catching that one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in e.g. some Acer Aspire 7750G.
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Signed-off-by: João Paulo Rechi Vita <jprvita@openbossa.org> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: James M. Leddy <james.leddy@canonical.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That commit replace the first msleep(20) with a busy-loop, but failed
to keep the 2nd msleep around. Later on we've replaced all these
msleep(20) by proper vblanks.
For reference also see the commit in xf86-video-intel:
Fix TV programming: add vblank wait after TV_CTL writes
Fxies FDO bug #14000; we need to wait for vblank after
writing TV_CTL or following "DPMS on" calls may not actually enable the output.
v2: As suggested by Chris Wilson, add a small comment to ensure that
no one accidentally removes this vblank wait again - there really
seems to be no sane explanation for why we need it, but it is
required.
Launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/763688 Reported-and-Tested-by: Robert Lowery <rglowery@exemail.com.au> Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've simply ignored this, which isn't too great. With this, interlaced
1080i works on my HDMI screen connected through sdvo. For no apparent
reason anything else still doesn't work as it should.
While at it, give these magic numbers in the dtd proper names and
add a comment that they match with EDID detailed timings.
v2: Actually use the right bit for interlaced.
Tested-by: Peter Ross <pross@xvid.org> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only override the ddc bus if the connector doesn't have
a valid one. The existing code overrode the ddc bus for
all connectors even if it had ddc bus.
Fixes ddc on another XFX card with the same pci ids that
was broken by the quirk overwriting the correct ddc bus.
Reported-by: Mehdi Aqadjani Memar <m.aqadjanimemar@student.ru.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a file OPEN is denied due to a share lock, the resulting
NFS4ERR_SHARE_DENIED is currently mapped to the default EIO.
This patch adds a more appropriate mapping, and brings Linux
into line with what Solaris 10 does.
See https://bugzilla.kernel.org/show_bug.cgi?id=43286
WLAN_STA_BLOCK_BA is set while suspending but doesn't get cleared
when resuming in case of wowlan. This causes further ADDBA requests
received to be rejected. Fix it by clearing it in the wowlan path
as well.
Signed-off-by: Eyal Shapira <eyal@wizery.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA support has finally made its way to the top of the TODO list, having
realised that a Geode using MMIO can't keep up with two ADSL2+ lines
each running at 21Mb/s.
This patch fixes a couple of bugs in the DMA support in the driver, so
once the corresponding FPGA update is complete and tested everything
should work properly.
We weren't storing the currently-transmitting skb, so we were never
unmapping it and never freeing/popping it when the TX was done.
And the addition of pci_set_master() is fairly self-explanatory.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Didn't quite fix the crash on boot. It moved it from PA1.1 processors to
PA2.0 narrow kernels. The final fix is to make sure the [id]tlb_miss_20 paths
also work. Even on narrow systems, these paths require using the wide
instructions becuase the tlb insertion format is wide. Fix this by
conditioning the dep[wd],z on whether we're being called from _11 or _20[w]
paths.
In certain configurations, the resulting kernel becomes too large to boot
because the linker places the long branch stubs for the merged .text section
at the very start of the image. As a result, the initial transfer of control
jumps to an unexpected location. Fix this by placing the head text in a
separate section so the stubs for .text are not at the start of the image.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While traversing the linked list of open file handles, if the identfied
file handle is invalid, a reopen is attempted and if it fails, we
resume traversing where we stopped and cifs can oops while accessing
invalid next element, for list might have changed.
So mark the invalid file handle and attempt reopen if no
valid file handle is found in rest of the list.
If reopen fails, move the invalid file handle to the end of the list
and start traversing the list again from the begining.
Repeat this four times before giving up and returning an error if
file reopen keeps failing.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When holding the mmap_sem for reading, pmd_offset_map_lock should only
run on a pmd_t that has been read atomically from the pmdp pointer,
otherwise we may read only half of it leading to this crash.
This should be a longstanding bug affecting x86 32bit PAE without THP.
Only archs with 64bit large pmd_t and 32bit unsigned long should be
affected.
With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad()
would partly hide the bug when the pmd transition from none to stable,
by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is
enabled a new set of problem arises by the fact could then transition
freely in any of the none, pmd_trans_huge or pmd_trans_stable states.
So making the barrier in pmd_none_or_trans_huge_or_clear_bad()
unconditional isn't good idea and it would be a flakey solution.
This should be fully fixed by introducing a pmd_read_atomic that reads
the pmd in order with THP disabled, or by reading the pmd atomically
with cmpxchg8b with THP enabled.
Luckily this new race condition only triggers in the places that must
already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix
is localized there but this bug is not related to THP.
NOTE: this can trigger on x86 32bit systems with PAE enabled with more
than 4G of ram, otherwise the high part of the pmd will never risk to be
truncated because it would be zero at all times, in turn so hiding the
SMP race.
This bug was discovered and fully debugged by Ulrich, quote:
----
[..]
pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and
eax.
496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t
*pmd)
497 {
498 /* depend on compiler for an atomic pmd read */
499 pmd_t pmdval = *pmd;
Please note that the PMD is not read atomically. These are two "mov"
instructions where the high order bits of the PMD entry are fetched
first. Hence, the above machine code is prone to the following race.
- The PMD entry {high|low} is 0x0000000000000000.
The "mov" at 0xc0507a84 loads 0x00000000 into edx.
- A page fault (on another CPU) sneaks in between the two "mov"
instructions and instantiates the PMD.
- The PMD entry {high|low} is now 0x00000003fda38067.
The "mov" at 0xc0507a8e loads 0xfda38067 into eax.
----
Reported-by: Ulrich Obergfell <uobergfe@redhat.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Larry Woodman <lwoodman@redhat.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 645747462435 ("vmscan: detect mapped file pages used only once")
made mapped pages have another round in inactive list because they might
be just short lived and so we could consider them again next time. This
heuristic helps to reduce pressure on the active list with a streaming
IO worklods.
This patch fixes a regression introduced by this commit for heavy shmem
based workloads because unlike Anon pages, which are excluded from this
heuristic because they are usually long lived, shmem pages are handled
as a regular page cache.
This doesn't work quite well, unfortunately, if the workload is mostly
backed by shmem (in memory database sitting on 80% of memory) with a
streaming IO in the background (backup - up to 20% of memory). Anon
inactive list is full of (dirty) shmem pages when watermarks are hit.
Shmem pages are kept in the inactive list (they are referenced) in the
first round and it is hard to reclaim anything else so we reach lower
scanning priorities very quickly which leads to an excessive swap out.
Let's fix this by excluding all swap backed pages (they tend to be long
lived wrt. the regular page cache anyway) from used-once heuristic and
rather activate them if they are referenced.
The customer's workload is shmem backed database (80% of RAM) and they
are measuring transactions/s with an IO in the background (20%).
Transactions touch more or less random rows in the table. The
transaction rate fell by a factor of 3 (in the worst case) because of
commit 64574746. This patch restores the previous numbers.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Minchan Kim <minchan@kernel.org> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't be holding the mmap_sem while calling flush_cache_user_range
because the flush can fault. If we fault on a user address, the
page fault handler will try to take mmap_sem again. Since both places
acquire the read lock, most of the time it succeeds. However, if another
thread tries to acquire the write lock on the mmap_sem (e.g. mmap) in
between the call to flush_cache_user_range and the fault, the down_read
in do_page_fault will deadlock.
[will: removed drop of vma parameter as already queued by rmk (7365/1)]
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Dima Zavin <dima@android.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vma isn't used and flush_cache_user_range isn't a standard macro that
is used on several archs with the same prototype. In fact only unicore32
has a macro with the same name (with an identical implementation and no
in-tree users).
This is a part of a patch proposed by Dima Zavin (with Message-id: 1272439931-12795-1-git-send-email-dima@android.com) that didn't get
accepted.
Cc: Dima Zavin <dima@android.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
Reported-by: Dave Jiang <dave.jiang@intel.com> Tested-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume. Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.
Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus pointed out that there was no value is checking whether m->ip
was zero - because zero is a legimate value. If we have a reliable
(or faked in the VM86 case) "m->cs" we can use it to tell whether we
were in user mode or kernelwhen the machine check hit.
This originally started as a patch from Bernard as a way of simply
setting the VS scheduler. After submitting the RFC patch, we decided to
also modify the DS scheduler. To be most explicit, I've made the patch
explicitly set all scheduler modes, and included the defines for other
modes (in case someone feels frisky later).
The rest of the story gets a bit weird. The first version of the patch
showed an almost unbelievable performance improvement. Since rebasing my
branch it appears the performance improvement has gone, unfortunately.
But setting these bits seem to be the right thing to do given that the
docs describe corruption that can occur with the default settings.
In summary, I am seeing no more perf improvements (or regressions) in my
limited testing, but we believe this should be set to prevent rendering
corruption, therefore cc stable.
v1: Clear bit 4 also (Ken + Eugeni)
Do a full clear + set of the bits we want (Me).
Cc: Bernard Kilarski <bernard.r.kilarski@intel.com>
Reviewed-by (RFC): Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sergio Correia <lists@uece.net> Tested-by: Sergio Correia <lists@uece.net> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit 04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dTD's next dtd pointer need to be updated once CPU writes it, or this
request may not be handled by controller, then host will get NAK from
device forever.
This problem occurs when there is a request is handling, we need to add
a new request to dTD list, if this new request is added before the current
one is finished, the new request is intended to added as next dtd pointer
at current dTD, but without wmb(), the dTD's next dtd pointer may not be
updated when the controller reads it. In that case, the controller will
still get Terminate Bit is 1 at dTD's next dtd pointer, that means there is
no next request, then this new request is missed by controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kontron M2M development board, also known as the Fish River Island II,
has an optional daughter card providing access to the PCH_UART (EG20T) via
a ti_usb_3410_5052 uart to usb chip.
projects / karo-tx-linux.git / log