For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values. Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.
This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Huaxu Wan [Fri, 25 Sep 2009 21:24:28 +0000 (14:24 -0700)]
iwlwifi: add module firmware info for 1000 series
The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Sep 2009 21:24:27 +0000 (14:24 -0700)]
iwlwifi: support idle for 6000 series hw
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 25 Sep 2009 21:24:26 +0000 (14:24 -0700)]
iwlwifi: Chain Noise Calibration for 6000 series
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Sep 2009 21:24:25 +0000 (14:24 -0700)]
iwlwifi: default to using all chains
When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.
Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Sep 2009 21:24:24 +0000 (14:24 -0700)]
iwlwifi: fix a typo
We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:54 +0000 (10:43 -0700)]
iwlwifi: add LED mode to support different LED behavior
Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.
The supported LED modes after this are:
IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
traffic
IWL_LED_RF_STATE (new) -
LED OFF: No power/RF disabled, the LED is emitting no light
LED ON: Powered/RF enabled, the LED is emitting light
in a stable non-flashing state.
In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:53 +0000 (10:43 -0700)]
iwlwifi: update PCI Subsystem ID for 6000 series
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:52 +0000 (10:43 -0700)]
iwlwifi: update PCI Subsystem ID for 1000 series
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:51 +0000 (10:43 -0700)]
iwlwifi: send cmd to uCode to configure valid tx antenna
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: add aggregation tables to the rate scaling algorithm
Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.
However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.
We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.
Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: do not clear TX info flags when receiving BlockAckResponse
OR-in AMPDU flags rather than assigning them. This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:47 +0000 (10:43 -0700)]
iwlwifi: use S_IRUGO and S_IWUSR in module parameters
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:46 +0000 (10:43 -0700)]
iwlwifi: EEPROM version for 1000 and 6000 series
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:45 +0000 (10:43 -0700)]
iwlwifi: allow user change protection mechanism for HT
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 17 Sep 2009 17:43:44 +0000 (10:43 -0700)]
iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:17 +0000 (10:38 -0700)]
iwlwifi: clarify and clean up chain settings
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:16 +0000 (10:38 -0700)]
iwlwifi: show NVM version in debugfs
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:15 +0000 (10:38 -0700)]
iwlwifi: clean up ht config naming
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:14 +0000 (10:38 -0700)]
iwlwifi: Adjust blink rate to compensate Clock difference
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 11 Sep 2009 17:38:13 +0000 (10:38 -0700)]
iwlwifi: clean up ht config a little
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:11 +0000 (10:38 -0700)]
iwlwifi: separate set_hw_params function for 6000 series
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:10 +0000 (10:38 -0700)]
iwlwifi: separate nic_config for different NIC
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:09 +0000 (10:38 -0700)]
iwlwifi: remove un-supported eeprom parameters
Remove few of the parameters not used and no longer valid in EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 11 Sep 2009 17:38:07 +0000 (10:38 -0700)]
iwlwifi: modify LED blink index table
Modify LED blink index table to include 1Mbps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was for supporting 25 MHz spacing for HT40, this is not used
as we use 20 MHz spacing instead for HT40 as per 802.11n. The hardware
is capable of it though so we leave the phymode definition and EEPROM
parsing for it. If some experimenter wants to work on this stuff stuff
you can add an extension enabling bool on ath_common and perhaps some
debugfs knob to enable it. Keep in mind you'll also need to update the
phymode with the AR_PHY_FC_DYN2040_EXT_CH which has been left on the
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can propagate better errors upon failed hw initialization,
and set up the ath_common structure for attach purposes. This
will become important once we start using the ath_common
for read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
atheros/ath9k: add common read/write ops and port ath9k to use it
In an effort to make hw code driver core agnostic read
and write operations are defined on the ath_common structure.
This patch adds that and makes ath9k use it. This allows
drivers like ath9k_htc to define its own read/write ops and
still rely on the same hw code. This also paves the way for
sharing code between ath9k/ath5k/ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Define bus agnostic bluetooth coex prep helper
We disable ASPM when enabling bluetooth coexistance. Disabling
ASPM is a bus specific operation. In the future other buses may
support bluetooth coexistance, an example is USB. To this end
move the current routine which disables ASPM into pci.c, and declare
it the PCI bt_coex_prep() helper. Additionally, since ASPM is
a PCI-Express primitive ensure we don't ever try to muck with ASPM
registers on non PCI-express devices.
This also cleans up hw.c to not include bus specific headers or
utilities.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com> Cc: Stephen Chen <stephen.chen@atheros.com> Cc: Zhifeng Cai <zhifeng.cai@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/ath/ath5k/attach.c
drivers/net/wireless/ath/ath5k/attach.c:288:42: warning: symbol 'ee' shadows an earlier one
drivers/net/wireless/ath/ath5k/attach.c:109:34: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
atheros/ath9k: move macaddr, curaid, curbssid and bssidmask to common
These are common amongst ath9k and ath5k, so put them into the
common structure and make ath9k to use it. ar9170 can use macaddr,
and curbssid. We'll change ath5k and ar9170 separately.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
atheros: use get_unaligned_le*() for bssid mask setting
Historically some macro helpers have been users for this,
AR5K_LOW_ID() and AR5K_HIGH_ID(), use upstream unaligned
helpers instead. This applid to ath5k and ar9170. ath9k
already uses this.
Worth noting is ath5k uses an ah_sta_id but that is already
the MAC address combined with the associaiton ID, ah_sta_id
is really ETH_ALEN in size.
Cc: Bob Copeland <me@bobcopeland.com> Cc: Nick Kossifidis <mick@madwifi-project.org> Cc: Christian Lamparter <chunkeey@web.de> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower() is a core driver helper with locking
protection. Locking protection should be left to the driver
core, not the hw code. Hardware code no longer contends for
locking when it needs to wake up the chip or put it to sleep.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: move ps helpers onto core driver when reseting tsf
When the TSF is reset power save state is disabled and
then restored. The helpers to disable power save and restore
it use a lock provided by the driver core. Move the callers
of the helpers outside of the hw code.
We reset the TSF when mac80211 tells us and on the beacon.c
helper ath9k_hw_beaconinit() when it is made explicitly required.
Add a helper on beacon.c which will deal with ps awake/restore
if we need to reset the TSF upon ath9k_hw_beaconinit().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep on btcoex.c only hardware access helpers, move the
driver core specific code to main.c. To accomplish
this we had to split ath_init_btcoex_info() into two parts,
the driver core part -- ath_init_btcoex_timer() and the hw
specific part -- ath9k_hw_init_btcoex_hw_info(). This
highlights how ath_gen_timer is part of the driver core, not
hw related, so stuff that into ath_btcoex struct.
The ath9k_hw_btcoex_init() code is now put inline on
ath_init_softc() through a switch to it easier to follow,
since we did that we can now call ath_tx_get_qnum() from
the main.c instead of btcoex.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: move btcoex core driver info to its own struct
There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: use ath_hw for DPRINTF() and debug init/exit
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 2 Oct 2009 17:54:34 +0000 (12:54 -0500)]
b43: Fix PPC crash in rfkill polling on unload
In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.
(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Tue, 6 Oct 2009 13:52:35 +0000 (15:52 +0200)]
mac80211: use kfree_skb() to free struct sk_buff pointers
kfree_skb() should be used to free struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 2 Oct 2009 20:44:07 +0000 (13:44 -0700)]
iwlagn: fix compile warning in iwl5000_gain_computation
The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.
This fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reported-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 2 Oct 2009 20:43:57 +0000 (13:43 -0700)]
iwlwifi: fix compile warning
Fixes following on big endian systems:
CC [M] drivers/net/wireless/iwlwifi/iwl-rx.o
drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
expression
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reported-by: Marcel Holtmann <marcel@holtmann.org> Tested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Oct 2009 20:43:56 +0000 (13:43 -0700)]
iwlwifi: fix EEPROM enhance tx power offset
Set the correct EEPROM offset for enhance tx power for 6000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jay Sternberg [Fri, 2 Oct 2009 20:43:55 +0000 (13:43 -0700)]
iwlwifi: incorrect method used for finding valid OTP blocks
The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.
The algorithm is simply valid blocks have a next address and that
address's contents is zero.
Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.
If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 1 Oct 2009 20:06:29 +0000 (22:06 +0200)]
mac80211: fix vlan and optimise RX
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Chou [Sun, 4 Oct 2009 23:33:20 +0000 (23:33 +0000)]
ethoc: use system memory as buffer
This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.
Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Chou [Sun, 4 Oct 2009 23:33:19 +0000 (23:33 +0000)]
ethoc: align received packet to make IP header at word boundary
The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
roel kluin [Tue, 6 Oct 2009 09:54:18 +0000 (09:54 +0000)]
au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 6 Oct 2009 19:34:39 +0000 (19:34 +0000)]
netxen: Fix Unlikely(x) > y
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>