Jan Glauber [Wed, 5 Dec 2012 23:20:14 +0000 (23:20 +0000)]
chelsio: remove get_clock and use ktime_get
The get_clock() of the chelsio driver clashes with the s390 one.
The chelsio helper reads a timespec via ktime just to convert it
back to ktime. I can see no different outcome from calling
ktime_get directly.
Remove the get_clock and use ktime_get directly.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barak Witkowski [Wed, 5 Dec 2012 23:04:03 +0000 (23:04 +0000)]
bnx2x: Prevent link flaps when booting from SAN.
It is possible that the driver is configured to operate with a certain
link configuration which differs from the link's configuration during
boot from SAN - this would cause the driver to flap the link.
Said flap may be missed by specific switches, causing dcbx convergence
to be too long and boot sequence to fail. Convergence is longer because
switch ignores new dcbx packets due to counters mismatch, as only host
side reset the counters due to the link flap.
This patch causes the driver to ignore user's initial configuration during
boot from SAN, and continues with the existing link configuration.
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
trem [Tue, 4 Dec 2012 08:52:10 +0000 (08:52 +0000)]
net: phy: smsc: force all capable mode if the phy is started in powerdown mode
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 6 Dec 2012 10:33:12 +0000 (10:33 +0000)]
cnic, bnx2x, bnx2: Simplify cnic probing.
Instead of using symbol_get(), cnic can now directly call the cnic_probe
functions in struct bnx2x and struct bnx2. symbol_get() is not reliable
as it fails when the module is still initializing.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 6 Dec 2012 10:33:08 +0000 (10:33 +0000)]
bnx2: Rename register read and write macros
with BNX2_ prefix for namespace consistency. Currently, these macro names
conflict with similar macros in bnx2x.h, preventing the cnic driver from
including both bnx2.h and bnx2x.h. Including bnx2x.h in cnic.c will remove
many redundant definitions and simplify the interface.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:03:07 +0000 (01:03 +0000)]
ipv4/route/rtnl: get mcast attributes when dst is multicast
Commit f1ce3062c538 (ipv4: Remove 'rt_dst' from 'struct rtable') removes the
call to ipmr_get_route(), which will get multicast parameters of the route.
I revert the part of the patch that remove this call. I think the goal was only
to get rid of rt_dst field.
The patch is only compiled-tested. My first idea was to remove ipmr_get_route()
because rt_fill_info() was the only user, but it seems the previous patch cleans
the code a bit too much ;-)
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Assmann [Tue, 4 Dec 2012 06:00:17 +0000 (06:00 +0000)]
igb: release already assigned MSI-X interrupts if setup fails
During MSI-X setup the system might run out of vectors. If this happens the
already assigned vectors for this NIC should be freed before trying the
disable MSI-X. Failing to do so results in the following oops.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Tue, 4 Dec 2012 06:00:12 +0000 (06:00 +0000)]
igb: remove duplicate code for fallback interrupt initialization
Given a small change to igb_init_interrupt_scheme() the function fits
igb_request_irq() for MSI/legacy interrupts initialization as well, instead of
duplicating most of its code there.
Also adding a missing igb_configure() to igb_request_irq() for MSI fallback
to work properly.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 4 Dec 2012 06:03:14 +0000 (06:03 +0000)]
ixgbe: check whether thermal sensor is enabled.
The X540's internal thermal sensor should not be enabled for all devices, but
only those devices which enable it in the NVM image. It is expected that
actively cooled devices will have it enabled, but passively cooled devices might
not want it enabled. This is due to passively cooled devices operating very near
the thermal threshold, sometimes within the margin of error of the thermal
sensor. Thus these devices may not be good candidates for using the thermal
sensor.
This patch uses the enabled bit in the FWSM register to check whether we should
be enabling the thermal sensor, and only sets the THERMAL_SENSOR_CAPABLE flag
for those devices which have it enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Wed, 24 Oct 2012 17:19:02 +0000 (17:19 +0000)]
ixgbe: Use is_valid_ether_addr
Use the normal kernel test instead of a module specific one.
Signed-off-by: Joe Perches <joe@perches.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:40 +0000 (09:56 -0500)]
rtl8187: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:39 +0000 (09:56 -0500)]
rt2x00: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: users@rt2x00.serialmonkey.com (moderated for non-subscribers) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:38 +0000 (09:56 -0500)]
p54: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:37 +0000 (09:56 -0500)]
orinoco: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:35 +0000 (09:56 -0500)]
libertas: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Dan Williams <dcbw@redhat.com> Cc: libertas-dev@lists.infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:34 +0000 (09:56 -0500)]
iwlwifi: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Johannes Berg <johannes.berg@intel.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: Intel Linux Wireless <ilw@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:32 +0000 (09:56 -0500)]
ipw2x00: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:31 +0000 (09:56 -0500)]
brcm80211: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: brcm80211-dev-list@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:29 +0000 (09:56 -0500)]
atmel: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:28 +0000 (09:56 -0500)]
ath5k: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Cc: linux-wireless@vger.kernel.org Cc: ath5k-devel@lists.ath5k.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:27 +0000 (09:56 -0500)]
wireless: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Pemberton [Mon, 3 Dec 2012 14:56:26 +0000 (09:56 -0500)]
rfkill: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:08 +0000 (18:46 +0100)]
ssb: register watchdog driver
Register the watchdog driver to the system if it is a SoC. Using the
watchdog on a non SoC device, like a PCI card, will make the PCI
card die when the timeout expired, but starting it again is not
supported by ssb.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:07 +0000 (18:46 +0100)]
ssb: extif: add methods for watchdog driver
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, add a method converting ms to ticks before setting the watchdog
register. Return the ticks or millisecond the timer was set to in case
the provided value was bigger than the max allowed value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:05 +0000 (18:46 +0100)]
ssb: add methods for watchdog driver
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:04 +0000 (18:46 +0100)]
ssb: set the PMU watchdog if available
Some ssb based devices have a PMU and the PMU watchdog register should
be used instead of the register in the chip common part, if the device
has a PMU. This patch also calculates the maximal number the watchdog
could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:02 +0000 (18:46 +0100)]
bcma: register watchdog driver
Register the watchdog driver to the system if this is a SoC. Using the
watchdog on a non SoC device, like a PCIe card, will make the PCIe
card die when the timeout expired, but starting it again is not
supported by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:01 +0000 (18:46 +0100)]
bcma: add methods for watchdog driver
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:46:00 +0000 (18:46 +0100)]
bcma: set the pmu watchdog if available
Mostly all bcma based devices have a PMU and the PMU watchdog should be
used and not the old one in chip common. This patch also calculates the
maximal number the watchdog could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Wed, 5 Dec 2012 17:45:58 +0000 (18:45 +0100)]
ssb/bcma: add common header for watchdog
This adds a common header for watchdog functions, so a watchdog driver
just needs to use this and could provide watchdog functionality for ssb
and bcma based SoCs. Patches for a watchdog driver using this interface
will be send later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Cc: stable@vger.kernel.org [3.7+] Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: explain why sta cannot be NULL for ampdus
Dan Carpenter reported that smatch detected a potential
problem with the code [1]:
drivers/net/wireless/ath/carl9170/tx.c:1488 carl9170_op_tx()
error: we previously assumed 'sta' could be null (see line 1482)
drivers/net/wireless/ath/carl9170/tx.c
1482 if (sta) {
^^^^^ New check.
[...]
1485 }
1487 if (info->flags & IEEE80211_TX_CTL_AMPDU) {
1488 run = carl9170_tx_ampdu_queue(ar, sta, skb);
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Old dereference of "sta" inside the call to carl9170_tx_ampdu_queue().
A range of solutions have been discussed in [2] and
we agreed on the following: "
> we might as well add a comment to carl9170_tx_ampdu_queue
> and explain the situation [in a way that's obvious to a
> human reader]. This way we can save the "if"... which is
> a small win since carl9170_op_tx is sort of a hot-path.
Putting a comment there is fine. Without the comment
it's easy for a human reader to get confused why the
check is there. So long as humans can read the code,
that's all that matters."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
LD drivers/net/wireless/brcm80211/built-in.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/fwil.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/fwil.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/fweh.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/fweh.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/dhd_common.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/dhd_common.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/sdio_chip.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/sdio_chip.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/usb.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/usb.o
CHECK drivers/net/wireless/brcm80211/brcmfmac/dhd_dbg.c
CC [M] drivers/net/wireless/brcm80211/brcmfmac/dhd_dbg.o
LD [M] drivers/net/wireless/brcm80211/brcmfmac/brcmfmac.o
LD drivers/net/wireless/brcm80211/brcmsmac/built-in.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c:1311:6: warning: context imbalance in 'brcms_down' - unexpected unlock
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c:1598:6: warning: context imbalance in 'brcms_rfkill_set_hw_state' - unexpected unlock
CC [M] drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/ucode_loader.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/ucode_loader.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/ampdu.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/ampdu.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/antsel.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/antsel.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/channel.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/channel.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/main.c
drivers/net/wireless/brcm80211/brcmsmac/main.c:6246:36: warning: Initializer entry defined twice
drivers/net/wireless/brcm80211/brcmsmac/main.c:6246:43: also defined here
CC [M] drivers/net/wireless/brcm80211/brcmsmac/main.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy_shim.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy_shim.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/pmu.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/pmu.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/rate.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/rate.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/stf.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/stf.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/aiutils.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/aiutils.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phy_cmn.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phy_cmn.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c:3313:46: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c:17688:47: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c:18187:53: warning: cast truncates bits from constant value (ffff3fff becomes 3fff)
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c:21160:36: warning: cast truncates bits from constant value (ffff3fff becomes 3fff)
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c:23321:35: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.c:28343:44: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phy_n.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_n.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_n.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/phy/phy_qmath.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/phy/phy_qmath.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/dma.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/dma.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/brcms_trace_events.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/brcms_trace_events.o
CHECK drivers/net/wireless/brcm80211/brcmsmac/debug.c
CC [M] drivers/net/wireless/brcm80211/brcmsmac/debug.o
LD [M] drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.o
LD drivers/net/wireless/brcm80211/brcmutil/built-in.o
CHECK drivers/net/wireless/brcm80211/brcmutil/utils.c
CC [M] drivers/net/wireless/brcm80211/brcmutil/utils.o
LD [M] drivers/net/wireless/brcm80211/brcmutil/brcmutil.o
Building modules, stage 2.
MODPOST 3 modules
CC drivers/net/wireless/brcm80211/brcmfmac/brcmfmac.mod.o
LD [M] drivers/net/wireless/brcm80211/brcmfmac/brcmfmac.ko
CC drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.mod.o
LD [M] drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko
CC drivers/net/wireless/brcm80211/brcmutil/brcmutil.mod.o
LD [M] drivers/net/wireless/brcm80211/brcmutil/brcmutil.ko
Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list@broadcom.com Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge tag 'nfc-fixes-3.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0
This is an NFC LLCP fix for 3.7 and contains only one patch.
It fixes a potential crash when receiving an LLCP HDLC frame acking a frame
that is not the last sent one. In that case we may dereference an already
freed pointer.
Cong Wang [Thu, 6 Dec 2012 02:04:04 +0000 (10:04 +0800)]
net: fix some compiler warning in net/core/neighbour.c
net/core/neighbour.c:65:12: warning: 'zero' defined but not used [-Wunused-variable]
net/core/neighbour.c:66:12: warning: 'unres_qlen_max' defined but not used [-Wunused-variable]
These variables are only used when CONFIG_SYSCTL is defined,
so move them under #ifdef CONFIG_SYSCTL.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Shan Wei <davidshan@tencent.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Dec 2012 21:24:45 +0000 (16:24 -0500)]
bridge: implement multicast fast leave
V3: make it a flag
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com>
Eddie Wai [Wed, 5 Dec 2012 10:10:15 +0000 (10:10 +0000)]
cnic: Fix rare race condition during iSCSI disconnect.
If the initiator and target try to close the connection at about the same
time, there is a race condition in the termination sequence for bnx2x.
Fix the problem by waiting for the remote termination to complete before
deleting the Connection ID. This will prevent the firmware assert.
Update version to 2.5.15.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Tue, 4 Dec 2012 18:49:15 +0000 (18:49 +0000)]
net: neighbour: prohibit negative value for unres_qlen_bytes parameter
unres_qlen_bytes and unres_qlen are int type.
But multiple relation(unres_qlen_bytes = unres_qlen * SKB_TRUESIZE(ETH_FRAME_LEN))
will cause type overflow when seting unres_qlen. e.g.
The gutted value is not that we setting。
But user/administrator don't know this is caused by int type overflow.
what's more, it is meaningless and even dangerous that unres_qlen_bytes is set
with negative number. Because, for unresolved neighbour address, kernel will cache packets
without limit in __neigh_event_send()(e.g. (u32)-1 = 2GB).
Signed-off-by: Shan Wei <davidshan@tencent.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Gallatin [Tue, 4 Dec 2012 10:17:15 +0000 (10:17 +0000)]
myri10ge: fix most sparse warnings
- convert remaining htonl/ntohl +__raw_read/__raw_writel to
swab32 + readl/writel
- add missing __iomem qualifier in myri10ge_open()
- fix dubious: x & !y warning by switching from logical to bitwise not
The swab32 conversion fixes a bug in myri10ge_led() where
big-endian machines would write the wrong pattern.
The only remaining warning (lock context imbalance) is due to
the use of __netif_tx_trylock(), and cannot easily be fixed.
Signed-off-by: Andrew Gallatin <gallatin@myri.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Mon, 3 Dec 2012 23:56:40 +0000 (23:56 +0000)]
bridge: implement multicast fast leave
V2: make the toggle per-port
Fast leave allows bridge to immediately stops the multicast
traffic on the port receives IGMP Leave when IGMP snooping is enabled,
no timeouts are observed.
Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Serge Hallyn [Mon, 3 Dec 2012 16:17:12 +0000 (16:17 +0000)]
net: dev_change_net_namespace: send a KOBJ_REMOVED/KOBJ_ADD
When a new nic is created in namespace ns1, the kernel sends a KOBJ_ADD uevent
to ns1. When the nic is moved to ns2, we only send a KOBJ_MOVE to ns2, and
nothing to ns1.
This patch changes that behavior so that when moving a nic from ns1 to ns2, we
send a KOBJ_REMOVED to ns1 and KOBJ_ADD to ns2. (The KOBJ_MOVE is still
sent to ns2).
The effects of this can be seen when starting and stopping containers in
an upstart based host. Lxc will create a pair of veth nics, the kernel
sends KOBJ_ADD, and upstart starts network-instance jobs for each. When
one nic is moved to the container, because no KOBJ_REMOVED event is
received, the network-instance job for that veth never goes away. This
was reported at https://bugs.launchpad.net/ubuntu/+source/lxc/+bug/1065589
With this patch the networ-instance jobs properly go away.
The other oddness solved here is that if a nic is passed into a running
upstart-based container, without this patch no network-instance job is
started in the container. But when the container creates a new nic
itself (ip link add new type veth) then network-interface jobs are
created. With this patch, behavior comes in line with a regular host.
v2: also send KOBJ_ADD to new netns. There will then be a
_MOVE event from the device_rename() call, but that should
be innocuous.
Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Daniel Lezcano <daniel.lezcano@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:13:41 +0000 (01:13 +0000)]
ip6mr: advertise new mfc entries via rtnl
This patch allows to monitor mf6c activities via rtnetlink.
To avoid parsing two times the mf6c oifs, we use maxvif to allocate the rtnl
msg, thus we may allocate some superfluous space.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:13:40 +0000 (01:13 +0000)]
ipmr: advertise new mfc entries via rtnl
This patch allows to monitor mfc activities via rtnetlink.
To avoid parsing two times the mfc oifs, we use maxvif to allocate the rtnl
msg, thus we may allocate some superfluous space.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:13:39 +0000 (01:13 +0000)]
ipmr/ip6mr: allow to get unresolved cache via netlink
/proc/net/ip[6]_mr_cache allows to get all mfc entries, even if they are put in
the unresolved list (mfc[6]_unres_queue). But only the table RT_TABLE_DEFAULT is
displayed.
This patch adds the parsing of the unresolved list when the dump is made via
rtnetlink, hence each table can be checked.
In IPv6, we set rtm_type in ip6mr_fill_mroute(), because in case of unresolved
mfc __ip6mr_fill_mroute() will not set it. In IPv4, it is already done.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:13:38 +0000 (01:13 +0000)]
ipmr/ip6mr: report origin of mfc entry into rtnl msg
A mfc entry can be static or not (added via the mroute_sk socket). The patch
reports MFC_STATIC flag into rtm_protocol by setting rtm_protocol to
RTPROT_STATIC or RTPROT_MROUTED.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Tue, 4 Dec 2012 01:13:37 +0000 (01:13 +0000)]
ipmr/ip6mr: advertise mfc stats via rtnetlink
These statistics can be checked only via /proc/net/ip_mr_cache or
SIOCGETSGCNT[_IN6] and thus only for the table RT_TABLE_DEFAULT.
Advertising them via rtnetlink allows to get statistics for all cache entries,
whatever the table is.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Dec 2012 18:01:19 +0000 (13:01 -0500)]
Merge branch 'master' of git://1984.lsi.us.es/nf-next
Pablo Neira Ayuso says:
====================
* Remove limitation in the maximum number of supported sets in ipset.
Now ipset automagically increments the number of slots in the array
of sets by 64 new spare slots, from Jozsef Kadlecsik.
* Partially remove the generic queue infrastructure now that ip_queue
is gone. Its only client is nfnetlink_queue now, from Florian
Westphal.
* Add missing attribute policy checkings in ctnetlink, from Florian
Westphal.
* Automagically kill conntrack entries that use the wrong output
interface for the masquerading case in case of routing changes,
from Jozsef Kadlecsik.
* Two patches two improve ct object traceability. Now ct objects are
always placed in any of the existing lists. This allows us to dump
the content of unconfirmed and dying conntracks via ctnetlink as
a way to provide more instrumentation in case you suspect leaks,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Tue, 4 Dec 2012 03:33:56 +0000 (03:33 +0000)]
qlcnic: update NIC partition interface routines
Refactor 82xx driver to support new adapter
Update routines to support variable number of NIC partitions
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Tue, 4 Dec 2012 03:33:54 +0000 (03:33 +0000)]
qlcnic: modify PCI and register access routines
Refactor 82xx driver to support new adapter
Update PCI and hardware access routines
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Tue, 4 Dec 2012 03:33:53 +0000 (03:33 +0000)]
qlcnic: move HW specific data to seperate structure
Move HW specific data to a seperate structure as part of
refactoring 82xx adapter driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 3 Dec 2012 19:37:00 +0000 (19:37 +0000)]
tg3: PTP - Enable the timestamping feature in hardware and fill skb tx/rx timestamps
This patch implements the hardware timestamping as described in
Documentation/networking/timestamping.txt
Update version to 3.128.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 3 Dec 2012 19:36:59 +0000 (19:36 +0000)]
tg3: PTP - Add the hardware timestamp ioctl
This patch implements the SIOCSHWTSTAMP ioctl as described in
Documentation/networking/timestamping.txt
[Removed HWTSTAMP_FILTER_ALL handling by returning -ERANGE based on input
from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 3 Dec 2012 19:36:58 +0000 (19:36 +0000)]
tg3: PTP - Implement the ptp api and ethtool functions
This patch adds the ptp_caps structure, ptp api implementation,
reference clock read and register/unregister functions. All the basic
clock operations as described in Documentation/ptp/ptp.txt are
supported.
Frequency adjustment is performed using hardware with a 24 bit
accumulator and a programmable correction value. On each clk, the
correction value gets added to the accumulator and when it overflows,
the time counter is incremented/decremented and the accumulator reset.
So conversion from ppb to correction value is
ppb * (1 << 24) / 1000000000
[Re-organized to put the ptp_clock_info struct declaration in one patch,
added ptp_clock_info.name, and added locking to tg3_ptp_adjtime() based
on input from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to write the reference clock. If a chip reset is
performed, the hwclock is reinitialized with the adjusted kernel time
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Fix inconsistent locking for tg3_netif_start().
Every caller holds tp->lock when calling tg3_netif_start() except
tg3_io_resume(). Fix it so that it is all consistent. The subsequent
PTP patches add tg3_ptp_resume() to tg3_netif_start() and the tp->lock
is required.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2012 20:35:28 +0000 (15:35 -0500)]
Merge tag 'dev_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Marks [Mon, 3 Dec 2012 10:26:54 +0000 (10:26 +0000)]
ipv6: Fix default route failover when CONFIG_IPV6_ROUTER_PREF=n
I believe this commit from 2008 was incorrect:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=398bcbebb6f721ac308df1e3d658c0029bb74503
When CONFIG_IPV6_ROUTER_PREF is disabled, the kernel should follow
RFC4861 section 6.3.6: if no route is NUD_VALID, then traffic should be
sprayed across all routers (indirectly triggering NUD) until one of them
becomes NUD_VALID.
However, the following experiment demonstrates that this does not work:
1) Connect to an IPv6 network.
2) Change the router's MAC (and link-local) address.
The kernel will lock onto the first router and never try the new one, even
if the first becomes unreachable. This patch fixes the problem by
allowing rt6_check_neigh() to return 0; if all routers return 0, then
rt6_select() will fall back to round-robin behavior.
This patch should have no effect when CONFIG_IPV6_ROUTER_PREF=y.
Note that rt6_check_neigh() is only used in a boolean context, so I've
changed its return type accordingly.
Signed-off-by: Paul Marks <pmarks@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Historically tun supported two modes of operation:
- in default mode, a small number of packets would get queued
at the device, the rest would be queued in qdisc
- in one queue mode, all packets would get queued at the device
This might have made sense up to a point where we made the
queue depth for both modes the same and set it to
a huge value (500) so unless the consumer
is stuck the chance of losing packets is small.
Thus in practice both modes behave the same, but the
default mode has some problems:
- if packets are never consumed, fragments are never orphaned
which cases a DOS for sender using zero copy transmit
- overrun errors are hard to diagnose: fifo error is incremented
only once so you can not distinguish between
userspace that is stuck and a transient failure,
tcpdump on the device does not show any traffic
Userspace solves this simply by enabling IFF_ONE_QUEUE
but there seems to be little point in not doing the
right thing for everyone, by default.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bill Pemberton [Mon, 3 Dec 2012 14:24:25 +0000 (09:24 -0500)]
net/intel: remove __dev* attributes
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: Carolyn Wyborny <carolyn.wyborny@intel.com> Cc: Don Skidmore <donald.c.skidmore@intel.com> Cc: Greg Rose <gregory.v.rose@intel.com> Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Cc: Alex Duyck <alexander.h.duyck@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: Tushar Dave <tushar.n.dave@intel.com> Cc: e1000-devel@lists.sourceforge.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>