]> git.karo-electronics.de Git - karo-tx-linux.git/log
karo-tx-linux.git
10 years agoARM: dts: vf610-twr: Add simple-card support.
Xiubo Li [Wed, 19 Feb 2014 07:42:31 +0000 (15:42 +0800)]
ARM: dts: vf610-twr: Add simple-card support.

This patch adds and enables simple-card support in DT node.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610-twr: Enable SGTL5000 codec.
Xiubo Li [Wed, 19 Feb 2014 07:42:30 +0000 (15:42 +0800)]
ARM: dts: vf610-twr: Enable SGTL5000 codec.

This patch adds and enables SGTL5000 codec support.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610-twr: Enable SAI ALSA SoC DAI device
Xiubo Li [Wed, 19 Feb 2014 07:42:29 +0000 (15:42 +0800)]
ARM: dts: vf610-twr: Enable SAI ALSA SoC DAI device

This patch adds and enables the SAI device.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610: Add edma mux Tx and Rx support for SAI node.
Xiubo Li [Wed, 19 Feb 2014 07:42:28 +0000 (15:42 +0800)]
ARM: dts: vf610: Add edma mux Tx and Rx support for SAI node.

This patch adds the SAI's edma mux Tx and Rx support.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610: lpuart: Add eDMA support
Yuan Yao [Mon, 17 Feb 2014 05:28:06 +0000 (13:28 +0800)]
ARM: dts: vf610: lpuart: Add eDMA support

Add lpuart dts node properties for eDMA support, them depend on the eDMA driver.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610: Add eDMA node
Jingchang Lu [Tue, 18 Feb 2014 02:17:11 +0000 (10:17 +0800)]
ARM: dts: vf610: Add eDMA node

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore: Add diagnostic PMIC LEDs
Alexander Shiyan [Sat, 15 Feb 2014 11:35:18 +0000 (15:35 +0400)]
ARM: dts: imx27-phytec-phycore: Add diagnostic PMIC LEDs

PCM-038 module have three triple LEDs connected to PMIC which
can be used for diagnostic purposes. This patch adds support
for these LEDs for PCM-038 SOM and adds basic LED-triggers for
these LEDs for PCM-970 RDK, the remaining LEDs are available
for use from userspace.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycard-s-som: Rename file to .dtsi
Alexander Shiyan [Tue, 11 Feb 2014 18:44:22 +0000 (22:44 +0400)]
ARM: dts: imx27-phytec-phycard-s-som: Rename file to .dtsi

PCA-100 module cannot be used standalone. This patch renames
module file to .dtsi and excludes it from compilation.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51 babbage: Support diagnostic LED
Liu Ying [Mon, 10 Feb 2014 07:05:46 +0000 (15:05 +0800)]
ARM: dts: i.MX51 babbage: Support diagnostic LED

The D25 LED controlled by gpio on the i.MX51 babbage
board is a diagnostic LED according to the board design.
This patch adds the relevant device tree nodes to the
i.MX51 babbage device tree file to support this LED.

Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx28-tx28: Remove 'enable-active-low' property
Fabio Estevam [Wed, 5 Feb 2014 13:10:10 +0000 (11:10 -0200)]
ARM: dts: imx28-tx28: Remove 'enable-active-low' property

'enable-active-low' is not a valid property for a GPIO controlled regulator.

According to Documentation/devicetree/bindings/regulator/gpio-regulator.txt:

"Optional properties:
...
- enable-active-high : Polarity of GPIO is active high (default is low)."

,so the correct way to define an active-low GPIO controlled regulator is to
simply not pass 'enable-active-high'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mx53: Remove 'enable-active-low' property
Fabio Estevam [Wed, 5 Feb 2014 13:10:09 +0000 (11:10 -0200)]
ARM: dts: mx53: Remove 'enable-active-low' property

'enable-active-low' is not a valid property for a GPIO controlled regulator.

According to Documentation/devicetree/bindings/regulator/gpio-regulator.txt:

"Optional properties:
...
- enable-active-high : Polarity of GPIO is active high (default is low)."

,so the correct way to define an active-low GPIO controlled regulator is to
simply not pass 'enable-active-high'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycard-s-rdk: Add pinctrl definitions for SDHC2
Alexander Shiyan [Tue, 4 Feb 2014 14:59:32 +0000 (18:59 +0400)]
ARM: dts: imx27-phytec-phycard-s-rdk: Add pinctrl definitions for SDHC2

This patch adds pinctrl definitions for SDHC2 for Phytec PCA100 RDK board.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycard-s-som: Add NFC node
Alexander Shiyan [Tue, 4 Feb 2014 14:59:31 +0000 (18:59 +0400)]
ARM: dts: imx27-phytec-phycard-s-som: Add NFC node

This patch adds the NFC devicetree node for Phytec PCA100 module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycard-s-som: Sort entries
Alexander Shiyan [Tue, 4 Feb 2014 14:59:30 +0000 (18:59 +0400)]
ARM: dts: imx27-phytec-phycard-s-som: Sort entries

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx28-m28cu3: Remove 'reset-active-high'
Fabio Estevam [Fri, 24 Jan 2014 20:45:24 +0000 (18:45 -0200)]
ARM: dts: imx28-m28cu3: Remove 'reset-active-high'

The 'reset-active-high' property is not defined anywhere, so just remove it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx5: use imx51-ssi
Markus Pargmann [Fri, 17 Jan 2014 09:07:42 +0000 (10:07 +0100)]
ARM: dts: imx5: use imx51-ssi

imx51-ssi and imx21-ssi are different IPs. imx51-ssi supports online
reconfiguration and needs this for correct interaction with SDMA. This
patch adds imx51-ssi before each imx21-ssi for all imx5 SoCs.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx51: Add mmc aliases
Sascha Hauer [Thu, 16 Jan 2014 12:44:21 +0000 (13:44 +0100)]
ARM: dts: imx51: Add mmc aliases

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Add mmc aliases
Sascha Hauer [Thu, 16 Jan 2014 12:44:18 +0000 (13:44 +0100)]
ARM: dts: imx53: Add mmc aliases

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: add support for Ka-Ro TX53 modules
Lothar Waßmann [Sat, 18 Jan 2014 08:18:38 +0000 (16:18 +0800)]
ARM: dts: imx53: add support for Ka-Ro TX53 modules

This patch adds support for the Ka-Ro electronics GmbH TX53 modules.
There are two distinct module types. One with an LVDS display
interface and SATA support, the other with a parallel LCD
interface and no SATA interface.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: Add support for the cpuimx35 board from Eukrea and its baseboard.
Denis Carikli [Wed, 15 Jan 2014 16:32:12 +0000 (17:32 +0100)]
ARM: dts: Add support for the cpuimx35 board from Eukrea and its baseboard.

The following devices/functionalities were added:
 * Main and secondary UARTs.
 * i2c and the pcf8563 device.
 * Ethernet.
 * NAND.
 * The BP1 button.
 * The LED.
 * Watchdog
 * SD.

Cc: Eric Bénard <eric@eukrea.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx28-apf28dev: add user button
Sébastien Szymanski [Tue, 14 Jan 2014 14:21:27 +0000 (15:21 +0100)]
ARM: dts: imx28-apf28dev: add user button

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51: Switch to use standard definitions for input subsystem
Alexander Shiyan [Sat, 11 Jan 2014 06:54:19 +0000 (10:54 +0400)]
ARM: dts: i.MX51: Switch to use standard definitions for input subsystem

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX53: add support for MCIMX53-START-R
Steffen Trumtrar [Fri, 10 Jan 2014 12:52:59 +0000 (13:52 +0100)]
ARM: dts: i.MX53: add support for MCIMX53-START-R

The "Start-R QSB" has a different PMIC than the older "Start QSB".
Add a new devicetree for the Start-R.
They both could use the same DT, as both PMICs (the dialog and the mc34708)
have different i2c addresses and could coexist in the same DT without any
errors. But once phandles are used, this will get messy.

The pmic nodes are based on an earlier patch

[PATCH] arm: imx53-qsb: Add Ripley driver DT nodes

from

Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>

which apparently got lost/abandoned.

I added phandles/newlines and changed the node name from ripley to mc34708.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX53: move common QSB nodes to new file
Steffen Trumtrar [Fri, 10 Jan 2014 12:52:58 +0000 (13:52 +0100)]
ARM: dts: i.MX53: move common QSB nodes to new file

There are (atleast) two versions of the i.MX53 LOCO:
            - the MCIMX53-START board
            - the MCIMX53-START-R board
The MCIMX53-START-R has a mc34708 pmic and is otherwise the similar to the
MCIMX53-START. To prepare for the START-R, move all common nodes to a new
imx53-qsb-common.dtsi and remove everything but the board name and pmic from
the imx53-qsb.dts.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53-evk: Remove board support
Alexander Shiyan [Wed, 8 Jan 2014 15:31:54 +0000 (19:31 +0400)]
ARM: dts: imx53-evk: Remove board support

imx53-evk board is discontinued by Freescale. The replacement is
imx53-qsb. Additionally this board is not supported by anyone and
in their current state is non-functional, for example PMIC not have
an IRQ line defined, so it is not works. This patch removes this DTS.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610: use the interrupt macros
Huang Shijie [Wed, 25 Dec 2013 06:19:27 +0000 (14:19 +0800)]
ARM: dts: vf610: use the interrupt macros

This patch uses the IRQ_TYPE_LEVEL_HIGH/IRQ_TYPE_NONE to replace
the hardcode.

[shawn.guo: While at it, we also fix the typo in uart0 interrupts
property, where the 0x00 should 0x04.  Hense, it should also be
IRQ_TYPE_LEVEL_HIGH just like other UART instances.]

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Add gpio and input dt includes.
Denis Carikli [Mon, 6 Jan 2014 16:16:07 +0000 (17:16 +0100)]
ARM: dts: imx53: Add gpio and input dt includes.

This is to permit to use of the includes in the boards dts.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX27: Add SSI nodes
Alexander Shiyan [Sat, 4 Jan 2014 18:28:35 +0000 (22:28 +0400)]
ARM: dts: i.MX27: Add SSI nodes

This patch adds the missing (Synchronous Serial Interface) SSI1 & SSI2
devicetree nodes for i.MX27 CPUs.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: add mxs phy controller id
Peter Chen [Fri, 20 Dec 2013 07:52:05 +0000 (15:52 +0800)]
ARM: dts: mxs: add mxs phy controller id

We need to use controller id to access different register regions
for mxs phy.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-rdk: Add pinctrl definitions for WEIM
Alexander Shiyan [Sat, 21 Dec 2013 07:11:42 +0000 (11:11 +0400)]
ARM: dts: imx27-phytec-phycore-rdk: Add pinctrl definitions for WEIM

This patch adds pinctrl definitions for WEIM CS4 and GPIO used as
CAN IRQ line.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-rdk: Add pingrp for SDHC
Alexander Shiyan [Sat, 21 Dec 2013 07:11:41 +0000 (11:11 +0400)]
ARM: dts: imx27-phytec-phycore-rdk: Add pingrp for SDHC

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Add spi-cs-high property to PMIC
Alexander Shiyan [Sat, 21 Dec 2013 07:11:39 +0000 (11:11 +0400)]
ARM: dts: imx27-phytec-phycore-som: Add spi-cs-high property to PMIC

Since SPI core does not use GPIO bindings for CS GPIOs,
we should add an active high level declaration.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-rdk: Enable 1-Wire module
Alexander Shiyan [Sat, 21 Dec 2013 07:11:38 +0000 (11:11 +0400)]
ARM: dts: imx27-phytec-phycore-rdk: Enable 1-Wire module

This patch enables 1-Wire module for Phytec PCM-970 RDK.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Add NFC pin group
Alexander Shiyan [Sat, 21 Dec 2013 07:11:37 +0000 (11:11 +0400)]
ARM: dts: imx27-phytec-phycore-som: Add NFC pin group

This patch adds pin group for NAND Flash Controller.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: Add support for the i.MX35.
Steffen Trumtrar [Wed, 18 Dec 2013 14:10:26 +0000 (15:10 +0100)]
ARM: dts: Add support for the i.MX35.

Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: Add iio-hwmon to mx23 soc
Alexandre Belloni [Wed, 18 Dec 2013 18:50:56 +0000 (19:50 +0100)]
ARM: dts: mxs: Add iio-hwmon to mx23 soc

This allows to read the SoC on-die temperature sensor available on the LRADC by
using:
 cat /sys/class/hwmon/hwmon0/device/temp1_input

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: Add iio-hwmon to mx28 soc
Alexandre Belloni [Wed, 18 Dec 2013 18:50:55 +0000 (19:50 +0100)]
ARM: dts: mxs: Add iio-hwmon to mx28 soc

This allows to read the SoC on-die temperature sensor available on the LRADC by
using:
 cat /sys/class/hwmon/hwmon0/device/temp1_input

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Rename file to .dtsi
Alexander Shiyan [Sat, 7 Dec 2013 08:26:36 +0000 (12:26 +0400)]
ARM: dts: imx27-phytec-phycore-som: Rename file to .dtsi

PCM-038 module cannot be used standalone. This patch renames
module file to .dtsi and excludes it from compilation.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Add pinctrl for CSPI1 and GPIOs used on module
Alexander Shiyan [Sat, 7 Dec 2013 08:26:35 +0000 (12:26 +0400)]
ARM: dts: imx27-phytec-phycore-som: Add pinctrl for CSPI1 and GPIOs used on module

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: add #io-channel-cells to mx28 lradc
Alexandre Belloni [Fri, 6 Dec 2013 20:20:31 +0000 (21:20 +0100)]
ARM: dts: mxs: add #io-channel-cells to mx28 lradc

Adding #io-channel-cells property to lradc allows us to use the lradc as
an iio provider.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: i.MX28: dts: rename usbphy pin names
Michael Grzeschik [Fri, 6 Dec 2013 14:56:40 +0000 (15:56 +0100)]
ARM: i.MX28: dts: rename usbphy pin names

The pins have nothing todo with the phy layer. We better rename them, so
it gets clear they are routed to the ehci core not to any phy.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: Add support for the cpuimx25 board from Eukrea and its baseboard.
Denis Carikli [Thu, 5 Dec 2013 14:56:56 +0000 (15:56 +0100)]
ARM: dts: Add support for the cpuimx25 board from Eukrea and its baseboard.

The following devices/functionalities were added:
 * Main and secondary UARTs.
 * i2c and the pcf8563 device.
 * Ethernet.
 * NAND.
 * The BP1 button.
 * The LED.
 * Watchdog
 * SD.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: mxs: Add support for the eukrea-cpuimx28.
Eric Bénard [Thu, 5 Dec 2013 13:28:06 +0000 (14:28 +0100)]
ARM: mxs: Add support for the eukrea-cpuimx28.

The following devices/functionalities were tested:
 * Main UART.
 * Ethernet0.
 * Ethernet1.
 * SD.
 * USB host.
 * USB otg.
 * Display(and its backlight).
 * Touchscreen.
 * Audio.
 * nand.
 * i2c and the pcf8563 device.
 * The gpio buttons.
 * The gpio leds.
 * Watchdog

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: Add a new pin config for the usb0 ID.
Denis Carikli [Thu, 5 Dec 2013 13:28:05 +0000 (14:28 +0100)]
ARM: dts: mxs: Add a new pin config for the usb0 ID.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: mxs: Add 18bit pin config for lcdif.
Denis Carikli [Thu, 5 Dec 2013 13:28:04 +0000 (14:28 +0100)]
ARM: dts: mxs: Add 18bit pin config for lcdif.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Enable AHCI SATA for imx53-qsb
Robert Nelson [Tue, 3 Dec 2013 14:39:38 +0000 (08:39 -0600)]
ARM: dts: imx53: Enable AHCI SATA for imx53-qsb

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX27: Configure GPIOs as "input" by default
Alexander Shiyan [Sat, 30 Nov 2013 07:03:20 +0000 (11:03 +0400)]
ARM: dts: i.MX27: Configure GPIOs as "input" by default

This patch changes the default direction for pins used
as GPIO to "input". This prevents a short circuit on the
configuration stage when GPIO-pin is connected to the
other output pin.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-apf27dev: Add pinctrl for cspi, sdhci, leds and keys
Gwenhael Goavec-Merou [Tue, 3 Dec 2013 11:10:15 +0000 (12:10 +0100)]
ARM: dts: imx27-apf27dev: Add pinctrl for cspi, sdhci, leds and keys

- add chip-select pinctrl for cspi
- add card-detect for sdhci2
- add pinctrl for gpio-leds and gpio-keys

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: apf27dev: Add pwm support
Gwenhael Goavec-Merou [Tue, 3 Dec 2013 11:10:14 +0000 (12:10 +0100)]
ARM: dts: apf27dev: Add pwm support

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: imx28: add apf28 specific initialization (macaddr)
Gwenhael Goavec-Merou [Sat, 30 Nov 2013 08:51:12 +0000 (09:51 +0100)]
ARM: imx28: add apf28 specific initialization (macaddr)

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: apf28dev: set gpio polarity for usb regulator and pinctrl for regulator...
Gwenhael Goavec-Merou [Sat, 30 Nov 2013 08:51:13 +0000 (09:51 +0100)]
ARM: dts: apf28dev: set gpio polarity for usb regulator and pinctrl for regulator gpio

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX27 boards: Switch to use standard GPIO and IRQ flags definitions
Alexander Shiyan [Sat, 30 Nov 2013 06:18:04 +0000 (10:18 +0400)]
ARM: dts: i.MX27 boards: Switch to use standard GPIO and IRQ flags definitions

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Update FEC node
Alexander Shiyan [Sat, 30 Nov 2013 06:18:03 +0000 (10:18 +0400)]
ARM: dts: imx27-phytec-phycore-som: Update FEC node

This patch updates FEC devicetree node of Phytec PCM038 module:
- Adding missing phy_mode properties.
- Adding fixed regulator to provide functionality without
  dummy-regulator in the kernel.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-rdk: Add DT node for camera module
Alexander Shiyan [Sat, 30 Nov 2013 06:18:02 +0000 (10:18 +0400)]
ARM: dts: imx27-phytec-phycore-rdk: Add DT node for camera module

This patch adds first I2C bus and PCA9536 device.
This device is used on Phytec PCM-970 RDK camera addon module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-phytec-phycore-som: Add on-flash BBT support
Alexander Shiyan [Sat, 30 Nov 2013 06:18:01 +0000 (10:18 +0400)]
ARM: dts: imx27-phytec-phycore-som: Add on-flash BBT support

This patch adds support for On Flash Bad Block Table for PCM-038
onboard NAND.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27: imx27-apf27dev: add pinctrl for cspi, i2c, sdhc and framebuffer
Gwenhael Goavec-Merou [Thu, 28 Nov 2013 07:19:32 +0000 (08:19 +0100)]
ARM: dts: imx27: imx27-apf27dev: add pinctrl for cspi, i2c, sdhc and framebuffer

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27: imx27-apf27: add pinctrl for fec and uart1
Gwenhael Goavec-Merou [Thu, 28 Nov 2013 07:19:31 +0000 (08:19 +0100)]
ARM: dts: imx27: imx27-apf27: add pinctrl for fec and uart1

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx51-babbage: Define FEC reset pin
Alexander Shiyan [Wed, 27 Nov 2013 11:55:46 +0000 (15:55 +0400)]
ARM: dts: imx51-babbage: Define FEC reset pin

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx51-babbage: Fix chipselect level for dataflash on spi0.1
Alexander Shiyan [Wed, 27 Nov 2013 11:55:45 +0000 (15:55 +0400)]
ARM: dts: imx51-babbage: Fix chipselect level for dataflash on spi0.1

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx28-evk: Run I2C0 at 400kHz
Fabio Estevam [Mon, 25 Nov 2013 17:47:39 +0000 (15:47 -0200)]
ARM: dts: imx28-evk: Run I2C0 at 400kHz

It is safe to operate I2C0 at 400kHz as SGTL5000 supports this frequency.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27-apf27dev: fix display size
Gwenhael Goavec-Merou [Mon, 25 Nov 2013 07:45:44 +0000 (08:45 +0100)]
ARM: dts: imx27-apf27dev: fix display size

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27 phycore pinctrl
Markus Pargmann [Sat, 8 Feb 2014 06:15:37 +0000 (14:15 +0800)]
ARM: dts: imx27 phycore pinctrl

Add pinctrl nodes and properties for phycore device nodes.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27 phycore move uart1 to rdk
Markus Pargmann [Wed, 20 Nov 2013 08:45:50 +0000 (09:45 +0100)]
ARM: dts: imx27 phycore move uart1 to rdk

uart1 is not used on SOM. It is passed directly to the rdk board.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27 phyCARD-S pinctrl
Markus Pargmann [Sat, 8 Feb 2014 05:54:43 +0000 (13:54 +0800)]
ARM: dts: imx27 phyCARD-S pinctrl

Add pinctrl nodes and properties for phyCARD-S device nodes.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27 iomux device node
Markus Pargmann [Wed, 20 Nov 2013 08:45:48 +0000 (09:45 +0100)]
ARM: dts: imx27 iomux device node

This patch adds a iomux node for imx27 pinctrl driver. The gpio
registers are embedded in the iomux memory area. So this patch moves
them into the iomux node for a better hardware description.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Enable AHCI SATA for M53EVK
Marek Vasut [Fri, 22 Nov 2013 11:05:04 +0000 (12:05 +0100)]
ARM: dts: imx53: Enable AHCI SATA for M53EVK

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Add AHCI SATA DT node
Marek Vasut [Fri, 22 Nov 2013 11:05:03 +0000 (12:05 +0100)]
ARM: dts: imx53: Add AHCI SATA DT node

The AHCI-IMX driver now supports i.MX53 as well. Add DT node.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51 boards: Switch to use standard GPIO flags definitions
Alexander Shiyan [Tue, 19 Nov 2013 11:47:27 +0000 (15:47 +0400)]
ARM: dts: i.MX51 boards: Switch to use standard GPIO flags definitions

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51: Move usbphy0 node from AIPS1
Alexander Shiyan [Tue, 19 Nov 2013 11:47:26 +0000 (15:47 +0400)]
ARM: dts: i.MX51: Move usbphy0 node from AIPS1

usbphy0 is not a part of AIPS1, so move this node under root.
Additionally this patch removes useless "status" property.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: cfa10036: Add dr_mode and phy_type properties to the DT
Maxime Ripard [Mon, 18 Nov 2013 14:52:02 +0000 (15:52 +0100)]
ARM: dts: cfa10036: Add dr_mode and phy_type properties to the DT

This USB port is only used as peripheral. Set it accordingly in its DT
node.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: mxs: cfa10049: Add NAU7802 ADCs to the device tree
Maxime Ripard [Mon, 18 Nov 2013 14:37:52 +0000 (15:37 +0100)]
ARM: mxs: cfa10049: Add NAU7802 ADCs to the device tree

The Crystalfontz CFA-10049 has 3 Nuvoton NAU7802 ADCs, plugged behing a
GPIO-controlled I2C muxer because these ADCs don't have a configurable
address.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Add USB support for M53EVK
Marek Vasut [Sun, 17 Nov 2013 03:04:50 +0000 (04:04 +0100)]
ARM: dts: imx53: Add USB support for M53EVK

Add USB support for M53EVK. The configuration is such that USB Host1
port is used as Host and the USB OTG port is used as Peripheral thus
far. Once OTG is properly fixed, the OTG will be further adjusted.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Fix backlight for M53EVK
Marek Vasut [Sun, 17 Nov 2013 01:19:40 +0000 (02:19 +0100)]
ARM: dts: imx53: Fix backlight for M53EVK

Remove the PWM backlight pin from the hog pins list, so it doesn't
collide with the PWM pin group. Moreover, add dummy regulator for
the backlight so that the backlight driver probes correctly.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: Fix display pinmux for M53EVK
Marek Vasut [Sun, 17 Nov 2013 01:19:39 +0000 (02:19 +0100)]
ARM: dts: imx53: Fix display pinmux for M53EVK

Use the DISP1 pinmux on M53EVK for the LCD, not the LVDS.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: imx50: use clock defines in DTS files
Lucas Stach [Thu, 14 Nov 2013 10:19:00 +0000 (11:19 +0100)]
ARM: imx50: use clock defines in DTS files

For better readability and no need to look up numbers
in the documentation anymore.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: imx51: use clock defines in DTS files
Lucas Stach [Thu, 14 Nov 2013 10:18:59 +0000 (11:18 +0100)]
ARM: imx51: use clock defines in DTS files

For better readability and no need to look up numbers
in the documentation anymore.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: imx53: use clock defines in DTS files
Lucas Stach [Thu, 14 Nov 2013 10:18:58 +0000 (11:18 +0100)]
ARM: imx53: use clock defines in DTS files

For better readability and no need to look up numbers
in the documentation anymore.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx27 pin functions
Markus Pargmann [Tue, 12 Nov 2013 08:50:04 +0000 (09:50 +0100)]
ARM: dts: imx27 pin functions

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: imx27-apf27dev: Add sdhci support
Gwenhael Goavec-Merou [Mon, 11 Nov 2013 17:56:49 +0000 (18:56 +0100)]
ARM: imx27-apf27dev: Add sdhci support

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51: Switch to use standard IRQ flags definitions
Alexander Shiyan [Thu, 7 Nov 2013 08:45:08 +0000 (12:45 +0400)]
ARM: dts: i.MX51: Switch to use standard IRQ flags definitions

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51: Add dummy clock to AUDMUX
Alexander Shiyan [Thu, 7 Nov 2013 08:45:06 +0000 (12:45 +0400)]
ARM: dts: i.MX51: Add dummy clock to AUDMUX

This patch adds dummy clock for AUDMUX. This change avoids useless
debug message "cannot get clock" during driver initialization.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX51: Update CPU node
Alexander Shiyan [Thu, 7 Nov 2013 08:45:05 +0000 (12:45 +0400)]
ARM: dts: i.MX51: Update CPU node

This patch updates i.MX51 CPU node:
- Alias for CPU is added to allow using this node in the parent DTS files.
- Removed useless "clock_names" property.
- "clock-latency" value increased to safe using with 32 kHz OSC.
- Defined operating points voltages and "voltage tolerance" properties.
  Values are safe for both commercial and industrial CPU variants.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: mxs: add support for I2SE's duckbill series
Michael Heimpold [Sat, 9 Nov 2013 11:14:16 +0000 (12:14 +0100)]
ARM: mxs: add support for I2SE's duckbill series

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx25.dtsi: label the iomuxc.
Denis Carikli [Wed, 6 Nov 2013 08:52:17 +0000 (09:52 +0100)]
ARM: dts: imx25.dtsi: label the iomuxc.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx25: Add pinctrl functions.
Denis Carikli [Wed, 6 Nov 2013 08:52:16 +0000 (09:52 +0100)]
ARM: dts: imx25: Add pinctrl functions.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx: use generic node name for fixed regulator
Shawn Guo [Fri, 7 Feb 2014 15:18:30 +0000 (23:18 +0800)]
ARM: dts: imx: use generic node name for fixed regulator

The device tree specification recommends that generic name should be
used for nodes.  So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53-mba53: create a container for fixed regulators
Shawn Guo [Wed, 6 Nov 2013 07:43:36 +0000 (15:43 +0800)]
ARM: dts: imx53-mba53: create a container for fixed regulators

To align with others on fixed regulators bindings, it adds node
'regulators' as the container and move all regulator-fixed nodes into
there.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: vf610: make pinctrl nodes board specific
Shawn Guo [Mon, 9 Dec 2013 06:42:54 +0000 (14:42 +0800)]
ARM: dts: vf610: make pinctrl nodes board specific

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Fugang Duan <B38611@freescale.com>
10 years agoARM: dts: imx51: make pinctrl nodes board specific
Shawn Guo [Mon, 4 Nov 2013 08:05:37 +0000 (16:05 +0800)]
ARM: dts: imx51: make pinctrl nodes board specific

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx53: make pinctrl nodes board specific
Shawn Guo [Mon, 4 Nov 2013 06:45:46 +0000 (14:45 +0800)]
ARM: dts: imx53: make pinctrl nodes board specific

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX53: Devicetree for Voipac Baseboard using x53-dmm-668 module
Rostislav Lisovy [Thu, 24 Oct 2013 21:56:09 +0000 (23:56 +0200)]
ARM: dts: i.MX53: Devicetree for Voipac Baseboard using x53-dmm-668 module

Supported peripherals: Audio -- headphone output, LEDs, Buttons
(using keyboard controller), SD-card.

Signed-off-by: Rostislav Lisovy <lisovy@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX53: dts for Voipac x53-dmm-668 module
Rostislav Lisovy [Thu, 24 Oct 2013 21:56:08 +0000 (23:56 +0200)]
ARM: dts: i.MX53: dts for Voipac x53-dmm-668 module

Enable uart1, ecspi1, i2c1, FEC and PMIC

Signed-off-by: Rostislav Lisovy <lisovy@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: Add vendor prefix for Voipac Technologies s.r.o.
Rostislav Lisovy [Thu, 24 Oct 2013 21:56:07 +0000 (23:56 +0200)]
ARM: dts: Add vendor prefix for Voipac Technologies s.r.o.

Signed-off-by: Rostislav Lisovy <lisovy@gmail.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx: add device tree support for Freescale imx50evk board
Greg Ungerer [Tue, 29 Oct 2013 05:15:57 +0000 (15:15 +1000)]
ARM: dts: imx: add device tree support for Freescale imx50evk board

Add device tree support for the Freescale IMX50EVk board based around the
IMX50 SoC. Supports UART, SPI flash, FEC ethernet and USB on this board.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx: add IMX50 SoC device tree
Greg Ungerer [Tue, 29 Oct 2013 05:15:56 +0000 (15:15 +1000)]
ARM: dts: imx: add IMX50 SoC device tree

Create device tree source for the Freescale IMX50 SoC. This was based on
the IMX53 source with changes made as necessary.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx: add device tree pin definitions for the IMX50
Greg Ungerer [Tue, 29 Oct 2013 05:15:55 +0000 (15:15 +1000)]
ARM: dts: imx: add device tree pin definitions for the IMX50

Add device tree pin function definitions for the Freescale IMX50 SoC.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: Add support for the cpuimx51 board from Eukrea and its baseboard.
Denis Carikli [Fri, 7 Feb 2014 07:50:23 +0000 (15:50 +0800)]
ARM: dts: Add support for the cpuimx51 board from Eukrea and its baseboard.

The following devices/functionalities were added:
 * Main and secondary UARTs.
 * i2c and the pcf8563 device.
 * Ethernet.
 * NAND.
 * The BP1 button.
 * The LED.
 * Watchdog
 * SD.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: imx25.dtsi: Add a label for the Audio Multiplexer.
Denis Carikli [Wed, 23 Oct 2013 08:29:34 +0000 (10:29 +0200)]
ARM: dts: imx25.dtsi: Add a label for the Audio Multiplexer.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX25: Add sdma script path.
Denis Carikli [Wed, 23 Oct 2013 08:29:33 +0000 (10:29 +0200)]
ARM: dts: i.MX25: Add sdma script path.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
10 years agoARM: dts: i.MX25: Add ssi clocks and DMA events.
Denis Carikli [Wed, 23 Oct 2013 08:29:32 +0000 (10:29 +0200)]
ARM: dts: i.MX25: Add ssi clocks and DMA events.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>