Pankaj Dubey [Fri, 24 Jan 2014 08:23:08 +0000 (08:23 +0000)]
arm64: fix build error if DMA_CMA is enabled
arm64/include/asm/dma-contiguous.h is trying to include
<asm-genric/dma-contiguous.h> which does not exist, and thus failing
build for arm64 if we enable CONFIG_DMA_CMA. This patch fixes build
error by removing unwanted header inclusion from arm64's dma-contiguous.h.
requires cpu_{suspend/resume} to restore the tpidr_el1 register upon resume
so that percpu variables can be addressed correctly when a CPU comes out
of reset from warm-boot.
This patch fixes cpu_{suspend}/{resume} tpidr_el1 restoration on resume, by
calling the set_my_cpu_offset C API, as it is done on primary and secondary
CPUs on cold boot, so that, even if the register used to store the percpu
offset is changed, the save and restore of general purpose registers does not
have to be updated.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jingoo Han [Tue, 21 Jan 2014 01:17:47 +0000 (01:17 +0000)]
arm64: mm: fix the function name in comment of __flush_dcache_area
Fix the function name of comment of __flush_dcache_area,
because __flush_dcache_area is the correct name. Also,
the missing variable 'size' is added to the comment.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jingoo Han [Mon, 20 Jan 2014 05:00:21 +0000 (05:00 +0000)]
arm64: mm: use ubfm for dcache_line_size
Use 'ubfm' for the bitfield move instruction; thus, single
instruction can be used instead of two instructions, when
getting the minimum D-cache line size from CTR_EL0 register.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arm64: kernel: restore HW breakpoint registers in cpu_suspend
When a CPU resumes from low-power, it restores HW breakpoint and
watchpoint slots through a CPU PM notifier. Since we want to enable
debugging as early as possible in the resume path, the mdscr content
is restored along the general purpose registers in the cpu_suspend API
and debug exceptions are reenabled when cpu_suspend returns. Since the
CPU PM notifier is run after a CPU has been resumed, we cannot expect
HW breakpoint registers to contain sane values till the notifier is run,
since the HW breakpoints registers content is unknown at reset; this means
that the CPU might run with debug exceptions enabled, mdscr restored but HW
breakpoint registers containing junk values that can trigger spurious
debug exceptions.
This patch fixes current HW breakpoints restore by moving the HW breakpoints
registers restoration to the cpu_suspend API, before the debug exceptions are
enabled. This way, as soon as the cpu_suspend function returns the
kernel can resume debugging with sane values in HW breakpoint registers.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jiang Liu [Tue, 7 Jan 2014 14:17:12 +0000 (22:17 +0800)]
arm64, jump label: detect %c support for ARM64
As commit a9468f30b5eac6 "ARM: 7333/2: jump label: detect %c
support for ARM", this patch detects the same thing for ARM64
because some ARM64 GCC versions have the same issue.
Some versions of ARM64 GCC which do support asm goto, do not
support the %c specifier. Since we need the %c to support jump
labels on ARM64, detect that too in the asm goto detection script
to avoid build errors with these versions.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jiang Liu <liuj97@gmail.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jiang Liu [Tue, 7 Jan 2014 14:17:10 +0000 (22:17 +0800)]
arm64: move encode_insn_immediate() from module.c to insn.c
Function encode_insn_immediate() will be used by other instruction
manipulate related functions, so move it into insn.c and rename it
as aarch64_insn_encode_immediate().
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jiang Liu <liuj97@gmail.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Jiang Liu [Tue, 7 Jan 2014 14:17:09 +0000 (22:17 +0800)]
arm64: introduce interfaces to hotpatch kernel and module code
Introduce three interfaces to patch kernel and module code:
aarch64_insn_patch_text_nosync():
patch code without synchronization, it's caller's responsibility
to synchronize all CPUs if needed.
aarch64_insn_patch_text_sync():
patch code and always synchronize with stop_machine()
aarch64_insn_patch_text():
patch code and synchronize with stop_machine() if needed
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Jiang Liu <liuj97@gmail.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Brown [Fri, 20 Dec 2013 12:52:44 +0000 (12:52 +0000)]
arm64: dts: Reduce size of virtio block device for foundation model
Will Deacon observed that kvmtool uses a size of 0x200 for virtio
block memory region and that the virtio block spec only uses 31 bytes in
the device specific region at 0x100 so reduce the region to a less
wasteful 0x200.
Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Geoff Levand [Sat, 14 Dec 2013 00:20:13 +0000 (00:20 +0000)]
arm64: Remove unused __data_loc variable
The __data_loc variable is an unused left over from the 32 bit arm implementation.
Remove that variable and adjust the __mmap_switched startup routine accordingly.
Laura Abbott [Thu, 12 Dec 2013 19:28:32 +0000 (19:28 +0000)]
arm64: Warn on NULL device structure for dma APIs
Although parts of the DMA apis may properly check for NULL devices,
there may be some places that don't. Rather than fix up all the
possible locations, just require a non-NULL device structure to be
used for allocating/freeing.
Cc: Will Deacon <will.deacon@arm.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[catalin.marinas@arm.com: s/WARN/WARN_ONCE/] Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Mon, 16 Dec 2013 21:04:36 +0000 (21:04 +0000)]
arm64: Add hwcaps for crypto and CRC32 extensions.
Advertise the optional cryptographic and CRC32 instructions to
user space where present. Several hwcap bits [3-7] are allocated.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
[bit 2 is taken now so use bits 3-7 instead] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Mon, 16 Dec 2013 21:04:35 +0000 (21:04 +0000)]
arm64: drop redundant macros from read_cpuid()
asm/cputype.h contains a bunch of #defines for CPU id registers
that essentially map to themselves. Remove the #defines and pass
the tokens directly to the inline asm() that reads the registers.
Mark Hambleton [Tue, 3 Dec 2013 19:19:12 +0000 (19:19 +0000)]
arm64: cmpxchg: update macros to prevent warnings
Make sure the value we are going to return is referenced in order to
avoid warnings from newer GCCs such as:
arch/arm64/include/asm/cmpxchg.h:162:3: warning: value computed is not used [-Wunused-value]
((__typeof__(*(ptr)))__cmpxchg_mb((ptr), \
^
net/netfilter/nf_conntrack_core.c:674:2: note: in expansion of macro ‘cmpxchg’
cmpxchg(&nf_conntrack_hash_rnd, 0, rand);
[Modified to use the current underlying implementation as current
mainline for both cmpxchg() and cmpxchg_local() does -- broonie]
Signed-off-by: Mark Hambleton <mahamble@broadcom.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
get_wchan() is lockless. Task may wakeup at any time and change its own stack,
thus each next stack frame may be overwritten and filled with random stuff.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv8 CPUs can perform efficient unaligned memory accesses in hardware
and this feature is relied up on by code such as the dcache
word-at-a-time name hashing.
This patch selects HAVE_EFFICIENT_UNALIGNED_ACCESS for arm64.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Wed, 6 Nov 2013 19:32:13 +0000 (19:32 +0000)]
arm64: dcache: select DCACHE_WORD_ACCESS for little-endian CPUs
DCACHE_WORD_ACCESS uses the word-at-a-time API for optimised string
comparisons in the vfs layer.
This patch implements support for load_unaligned_zeropad in much the
same way as has been done for ARM, although big-endian systems are also
supported.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Wed, 6 Nov 2013 17:20:22 +0000 (17:20 +0000)]
arm64: use generic strnlen_user and strncpy_from_user functions
This patch implements the word-at-a-time interface for arm64 using the
same algorithm as ARM. We use the fls64 macro, which expands to a clz
instruction via a compiler builtin. Big-endian configurations make use
of the implementation from asm-generic.
With this implemented, we can replace our byte-at-a-time strnlen_user
and strncpy_from_user functions with the optimised generic versions.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Vinayak Kale [Wed, 4 Dec 2013 10:09:50 +0000 (10:09 +0000)]
genirq: Add an accessor for IRQ_PER_CPU flag
This patch adds an accessor function for IRQ_PER_CPU flag.
The accessor function is useful to determine whether an IRQ is percpu or not.
This patch is based on an older patch posted by Chris Smith here [1].
There is a minor change w.r.t. Chris's original patch: The accessor function
is renamed as 'irq_is_percpu' instead of 'irq_is_per_cpu'.
Signed-off-by: Chris Smith <chris.smith@st.com> Signed-off-by: Vinayak Kale <vkale@apm.com> Acked-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Thu, 12 Dec 2013 12:34:05 +0000 (12:34 +0000)]
arm64: vmlinux.lds.S: drop redundant .comment
We currently try to emit .comment twice, once in STABS_DEBUG, and once
in the line immediately following it. As the two section definitions are
identical, the latter is redundant and can be dropped.
This patch drops the redundant .comment section definition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Hambleton [Tue, 3 Dec 2013 19:58:42 +0000 (19:58 +0000)]
arm64: dts: Add a virtio disk to the RTSM motherboard
Describe the virtio device so we can mount disk images in the simulator.
[Reduced the size of the region based on feedback from review -- broonie]
Signed-off-by: Mark Hambleton <mahamble@broadcom.com> Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Laura Abbott [Wed, 11 Dec 2013 01:23:02 +0000 (01:23 +0000)]
arm64: Correct virt_addr_valid
The definition of virt_addr_valid is that virt_addr_valid should
return true if and only if virt_to_page returns a valid pointer.
The current definition of virt_addr_valid only checks against the
virtual address range. There's no guarantee that just because a
virtual address falls bewteen PAGE_OFFSET and high_memory the
associated physical memory has a valid backing struct page. Follow
the example of other architectures and convert to pfn_valid to
verify that the virtual address is actually valid.
Cc: Will Deacon <will.deacon@arm.com> Cc: Nicolas Pitre <nico@linaro.org> Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the required makefile and kconfig entries to enable PM
for arm64 systems.
The kernel relies on the cpu_{suspend}/{resume} infrastructure to
properly save the context for a CPU and put it to sleep, hence this
patch adds the config option required to enable cpu_{suspend}/{resume}
API.
In order to rely on the CPU PM implementation for saving and restoring
of CPU subsystems like GIC and PMU, the arch Kconfig must be also
augmented to select the CONFIG_CPU_PM option when SUSPEND or CPU_IDLE
kernel implementations are selected.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When CPU idle is enabled, the architectural idle call should go through
the idle subsystem to allow CPUs to enter idle states defined
by the platform CPU idle back-end operations.
This patch, mirroring other archs behaviour, adds the CPU idle call to the
architectural arch_cpu_idle implementation for arm64.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On platforms with power management capabilities, timers that are shut
down when a CPU enters deep C-states must be emulated using an always-on
timer and a timer IPI to relay the timer IRQ to target CPUs on an SMP
system.
This patch enables the generic clockevents broadcast infrastructure for
arm64, by providing the required Kconfig entries and adding the timer
IPI infrastructure.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
arm64: kernel: implement HW breakpoints CPU PM notifier
When a CPU is shutdown either through CPU idle or suspend to RAM, the
content of HW breakpoint registers must be reset or restored to proper
values when CPU resume from low power states. This patch adds debug register
restore operations to the HW breakpoint control function and implements a
CPU PM notifier that allows to restore the content of HW breakpoint registers
to allow proper suspend/resume operations.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
arm64: kernel: refactor code to install/uninstall breakpoints
Most of the code executed to install and uninstall breakpoints is
common and can be factored out in a function that through a runtime
operations type provides the requested implementation.
This patch creates a common function that can be used to install/uninstall
breakpoints and defines the set of operations that can be carried out
through it.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Upon CPU shutdown and consequent warm-reboot, the hypervisor CPU state
must be re-initialized. This patch implements a CPU PM notifier that
upon warm-boot calls a KVM hook to reinitialize properly the hypervisor
state so that the CPU can be safely resumed.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When a CPU enters a low power state, its FP register content is lost.
This patch adds a notifier to save the FP context on CPU shutdown
and restore it on CPU resume. The context is saved and restored only
if the suspending thread is not a kernel thread, mirroring the current
context switch behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Kernel subsystems like CPU idle and suspend to RAM require a generic
mechanism to suspend a processor, save its context and put it into
a quiescent state. The cpu_{suspend}/{resume} implementation provides
such a framework through a kernel interface allowing to save/restore
registers, flush the context to DRAM and suspend/resume to/from
low-power states where processor context may be lost.
The CPU suspend implementation relies on the suspend protocol registered
in CPU operations to carry out a suspend request after context is
saved and flushed to DRAM. The cpu_suspend interface:
int cpu_suspend(unsigned long arg);
allows to pass an opaque parameter that is handed over to the suspend CPU
operations back-end so that it can take action according to the
semantics attached to it. The arg parameter allows suspend to RAM and CPU
idle drivers to communicate to suspend protocol back-ends; it requires
standardization so that the interface can be reused seamlessly across
systems, paving the way for generic drivers.
Context memory is allocated on the stack, whose address is stashed in a
per-cpu variable to keep track of it and passed to core functions that
save/restore the registers required by the architecture.
Even though, upon successful execution, the cpu_suspend function shuts
down the suspending processor, the warm boot resume mechanism, based
on the cpu_resume function, makes the resume path operate as a
cpu_suspend function return, so that cpu_suspend can be treated as a C
function by the caller, which simplifies coding the PM drivers that rely
on the cpu_suspend API.
Upon context save, the minimal amount of memory is flushed to DRAM so
that it can be retrieved when the MMU is off and caches are not searched.
The suspend CPU operation, depending on the required operations (eg CPU vs
Cluster shutdown) is in charge of flushing the cache hierarchy either
implicitly (by calling firmware implementations like PSCI) or explicitly
by executing the required cache maintainance functions.
Debug exceptions are disabled during cpu_{suspend}/{resume} operations
so that debug registers can be saved and restored properly preventing
preemption from debug agents enabled in the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Power management software requires the kernel to save and restore
CPU registers while going through suspend and resume operations
triggered by kernel subsystems like CPU idle and suspend to RAM.
This patch implements code that provides save and restore mechanism
for the arm v8 implementation. Memory for the context is passed as
parameter to both cpu_do_suspend and cpu_do_resume functions, and allows
the callers to implement context allocation as they deem fit.
The registers that are saved and restored correspond to the registers set
actually required by the kernel to be up and running which represents a
subset of v8 ISA.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
arm64: kernel: build MPIDR_EL1 hash function data structure
On ARM64 SMP systems, cores are identified by their MPIDR_EL1 register.
The MPIDR_EL1 guidelines in the ARM ARM do not provide strict enforcement of
MPIDR_EL1 layout, only recommendations that, if followed, split the MPIDR_EL1
on ARM 64 bit platforms in four affinity levels. In multi-cluster
systems like big.LITTLE, if the affinity guidelines are followed, the
MPIDR_EL1 can not be considered a linear index. This means that the
association between logical CPU in the kernel and the HW CPU identifier
becomes somewhat more complicated requiring methods like hashing to
associate a given MPIDR_EL1 to a CPU logical index, in order for the look-up
to be carried out in an efficient and scalable way.
This patch provides a function in the kernel that starting from the
cpu_logical_map, implement collision-free hashing of MPIDR_EL1 values by
checking all significative bits of MPIDR_EL1 affinity level bitfields.
The hashing can then be carried out through bits shifting and ORing; the
resulting hash algorithm is a collision-free though not minimal hash that can
be executed with few assembly instructions. The mpidr_el1 is filtered through a
mpidr mask that is built by checking all bits that toggle in the set of
MPIDR_EL1s corresponding to possible CPUs. Bits that do not toggle do not
carry information so they do not contribute to the resulting hash.
Pseudo code:
/* check all bits that toggle, so they are required */
for (i = 1, mpidr_el1_mask = 0; i < num_possible_cpus(); i++)
mpidr_el1_mask |= (cpu_logical_map(i) ^ cpu_logical_map(0));
/*
* Build shifts to be applied to aff0, aff1, aff2, aff3 values to hash the
* mpidr_el1
* fls() returns the last bit set in a word, 0 if none
* ffs() returns the first bit set in a word, 0 if none
*/
fs0 = mpidr_el1_mask[7:0] ? ffs(mpidr_el1_mask[7:0]) - 1 : 0;
fs1 = mpidr_el1_mask[15:8] ? ffs(mpidr_el1_mask[15:8]) - 1 : 0;
fs2 = mpidr_el1_mask[23:16] ? ffs(mpidr_el1_mask[23:16]) - 1 : 0;
fs3 = mpidr_el1_mask[39:32] ? ffs(mpidr_el1_mask[39:32]) - 1 : 0;
ls0 = fls(mpidr_el1_mask[7:0]);
ls1 = fls(mpidr_el1_mask[15:8]);
ls2 = fls(mpidr_el1_mask[23:16]);
ls3 = fls(mpidr_el1_mask[39:32]);
bits0 = ls0 - fs0;
bits1 = ls1 - fs1;
bits2 = ls2 - fs2;
bits3 = ls3 - fs3;
aff0_shift = fs0;
aff1_shift = 8 + fs1 - bits0;
aff2_shift = 16 + fs2 - (bits0 + bits1);
aff3_shift = 32 + fs3 - (bits0 + bits1 + bits2);
u32 hash(u64 mpidr_el1) {
u32 l[4];
u64 mpidr_el1_masked = mpidr_el1 & mpidr_el1_mask;
l[0] = mpidr_el1_masked & 0xff;
l[1] = mpidr_el1_masked & 0xff00;
l[2] = mpidr_el1_masked & 0xff0000;
l[3] = mpidr_el1_masked & 0xff00000000;
return (l[0] >> aff0_shift | l[1] >> aff1_shift | l[2] >> aff2_shift |
l[3] >> aff3_shift);
}
The hashing algorithm relies on the inherent properties set in the ARM ARM
recommendations for the MPIDR_EL1. Exotic configurations, where for instance
the MPIDR_EL1 values at a given affinity level have large holes, can end up
requiring big hash tables since the compression of values that can be achieved
through shifting is somewhat crippled when holes are present. Kernel warns if
the number of buckets of the resulting hash table exceeds the number of
possible CPUs by a factor of 4, which is a symptom of a very sparse HW
MPIDR_EL1 configuration.
The hash algorithm is quite simple and can easily be implemented in assembly
code, to be used in code paths where the kernel virtual address space is
not set-up (ie cpu_resume) and instruction and data fetches are strongly
ordered so code must be compact and must carry out few data accesses.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In order to simplify access to different affinity levels within the
MPIDR_EL1 register values, this patch implements some preprocessor
macros that allow to retrieve the MPIDR_EL1 affinity level value according
to the level passed as input parameter.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Matias Bjorling [Tue, 10 Dec 2013 15:50:38 +0000 (16:50 +0100)]
null_blk: mem garbage on NUMA systems during init
For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.
This makes the null_init_hctx function overwrite memory outside of what
it allocated. In my case it lead to writing garbage into struct
request_queue's mq_map.
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Since commit ec39f64bba34 ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.
Fix them by using dev_get_drvdata(), in order to avoid this oops:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Linus Torvalds [Sun, 15 Dec 2013 19:52:47 +0000 (11:52 -0800)]
Merge branch 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a pretty small batch:
The biggest single change is to stop using EFI time services on 32-bit
platforms. This matches our current behavior on 64-bit platforms as
we already had ruled them out there as being too unreliable. Turns
out that affects 32-bit platforms, too.
One NULL pointer fix for SGI UV.
Two minor build fixes, one of which only affects icc and the other
which affects icc and future versions or nonstandard default settings
of gcc"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Don't use (U)EFI time services on 32 bit
x86, build, icc: Remove uninitialized_var() from compiler-intel.h
x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
x86, build: Pass in additional -mno-mmx, -mno-sse options
Linus Torvalds [Sun, 15 Dec 2013 19:45:27 +0000 (11:45 -0800)]
Merge tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI device hotplug
- Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
Wysocki)
Host bridge drivers
- Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
Helgaas)
- mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
(Jason Gunthorpe)
Miscellaneous
- Avoid unnecessary CPU switch when calling .probe() (Alexander
Duyck)
- Revert "workqueue: allow work_on_cpu() to be called recursively"
(Bjorn Helgaas)
- Disable Bus Master only on kexec reboot (Khalid Aziz)
- Omit PCI ID macro strings to shorten quirk names for LTO (Michal
Marek)"
* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
PCI: Disable Bus Master only on kexec reboot
PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
PCI: Omit PCI ID macro strings to shorten quirk names
PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
Revert "workqueue: allow work_on_cpu() to be called recursively"
PCI: Avoid unnecessary CPU switch when calling driver .probe() method
Linus Torvalds [Sun, 15 Dec 2013 19:28:02 +0000 (11:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
selinux: look for IPsec labels on both inbound and outbound packets
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
selinux: fix possible memory leak
and Josh Boyer bisected it down to this commit. Reverting the commit in
the rawhide kernel fixes the problem.
Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.
Reported-by: Tom London <selinux@gmail.com> Bisected-by: Josh Boyer <jwboyer@fedoraproject.org> Acked-by: Eric Paris <eparis@redhat.com> Cc: James Morris <jmorris@namei.org> Cc: Anand Avati <avati@redhat.com> Cc: Paul Moore <paul@paul-moore.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carolyn Wyborny [Sat, 14 Dec 2013 11:26:46 +0000 (03:26 -0800)]
igb: Fix for issue where values could be too high for udelay function.
This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.
CC: stable kernel <stable@vger.kernel.org> # 3.9+ Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com> Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Sat, 14 Dec 2013 11:26:45 +0000 (03:26 -0800)]
i40e: fix null dereference
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Dec 2013 00:16:03 +0000 (16:16 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
Linus Torvalds [Sat, 14 Dec 2013 00:14:39 +0000 (16:14 -0800)]
Merge tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"These are couple of weeks old already, but I just couldn't get them to
you earlier.
- couple of fixes for recently added perf code
- build time extable sort"
* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [perf] Fix a few thinkos
ARC: Add guard macro to uapi/asm/unistd.h
ARC: extable: Enable sorting at build time
Linus Torvalds [Fri, 13 Dec 2013 21:22:22 +0000 (13:22 -0800)]
Merge tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A set of device-mapper fixes for 3.13.
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-
provisioning and caching targets as a result of increased regression
testing using the device-mapper-test-suite (dmts). The most notable
of these are the reference counting fixes for the space map btree that
is used by the dm-array interface -- without these the dm-cache
metadata will leak, resulting in dm-cache devices running out of
metadata blocks. Also, some important fixes related to the
thin-provisioning target's transition to read-only mode on error"
* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
dm stats: initialize read-only module parameter
dm bufio: initialize read-only module parameters
dm cache: actually resize cache
dm cache: update Documentation for invalidate_cblocks's range syntax
dm cache policy mq: fix promotions to occur as expected
dm thin: allow pool in read-only mode to transition to read-write mode
dm thin: re-establish read-only state when switching to fail mode
dm thin: always fallback the pool mode if commit fails
dm thin: switch to read-only mode if metadata space is exhausted
dm thin: switch to read only mode if a mapping insert fails
dm space map metadata: return on failure in sm_metadata_new_block
dm table: fail dm_table_create on dm_round_up overflow
dm snapshot: avoid snapshot space leak on crash
dm delay: fix a possible deadlock due to shared workqueue
Russell King [Tue, 10 Dec 2013 19:21:08 +0000 (19:21 +0000)]
ARM: fix asm/memory.h build error
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06cd4 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions") Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Fri, 13 Dec 2013 19:39:54 +0000 (11:39 -0800)]
Merge tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Linus Torvalds [Fri, 13 Dec 2013 19:38:35 +0000 (11:38 -0800)]
Merge tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two small changes to fix some error handling and checking (both of
which would be quite serious if the errors trigger) plus a trivial
documentation fix"
* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use IS_ERR() to check clk_get() results
regmap: make sure we unlock on failure in regmap_bulk_write
regmap: trivial comment fix (copy'n'paste error)
Linus Torvalds [Fri, 13 Dec 2013 19:37:57 +0000 (11:37 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two simple but wanted fixes for the i2c subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: Check the return value from clk_prepare_enable()
i2c: mux: Inherit retry count and timeout from parent for muxed bus
Linus Torvalds [Fri, 13 Dec 2013 19:31:22 +0000 (11:31 -0800)]
Merge tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes, for the pxa3xx-nand driver:
- This driver was not ready to fully Armada 370 NAND, with
particularly notable problems seen on flash with 2KB page sizes.
This "compatible" entry really should have been held back until
3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe
attempt, where we free unallocated DMA resources"
* tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd:
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
Linus Torvalds [Fri, 13 Dec 2013 19:29:51 +0000 (11:29 -0800)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the common fixes PULL for dmaengine.
Dan has been working on fixing the build issues in bunch of drivers.
Here we have one fixing s3c24xx-dma, along with fix from Russell on
pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which
was added in last merge window missed updates to usage of DMA_COMPLETE
so converting the last driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix build breakage in s3c24xx-dma
Fix pl08x warnings
rcar-hpbdma: initialise plane information when halted
rcar-hpbdma: fixup channel busy check for double plane
rcar-hpbdma: add max transfer size
dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
Joe Thornber [Fri, 13 Dec 2013 12:31:08 +0000 (12:31 +0000)]
dm space map: disallow decrementing a reference count below zero
The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc"). To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.
Add a DMERR to reflect the potential seriousness of this error.
Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.
With this fix the following dmts regression test now passes:
dmtest run --suite cache -n /metadata_use_kernel/
The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 3.12+
Linus Torvalds [Fri, 13 Dec 2013 02:22:10 +0000 (18:22 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
include/linux/hugetlb.h: make isolate_huge_page() an inline
Johannes Weiner [Fri, 13 Dec 2013 01:12:35 +0000 (17:12 -0800)]
mm: memcg: do not allow task about to OOM kill to bypass the limit
Commit 4942642080ea ("mm: memcg: handle non-error OOM situations more
gracefully") allowed tasks that already entered a memcg OOM condition to
bypass the memcg limit on subsequent allocation attempts hoping this
would expedite finishing the page fault and executing the kill.
David Rientjes is worried that this breaks memcg isolation guarantees
and since there is no evidence that the bypass actually speeds up fault
processing just change it so that these subsequent charge attempts fail
outright. The notable exception being __GFP_NOFAIL charges which are
required to bypass the limit regardless.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: David Rientjes <rientjes@google.com> Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-bt: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:34 +0000 (17:12 -0800)]
mm: memcg: fix race condition between memcg teardown and swapin
There is a race condition between a memcg being torn down and a swapin
triggered from a different memcg of a page that was recorded to belong
to the exiting memcg on swapout (with CONFIG_MEMCG_SWAP extension). The
result is unreclaimable pages pointing to dead memcgs, which can lead to
anything from endless loops in later memcg teardown (the page is charged
to all hierarchical parents but is not on any LRU list) or crashes from
following the dangling memcg pointer.
Memcgs with tasks in them can not be torn down and usually charges don't
show up in memcgs without tasks. Swapin with the CONFIG_MEMCG_SWAP
extension is the notable exception because it charges the cgroup that
was recorded as owner during swapout, which may be empty and in the
process of being torn down when a task in another memcg triggers the
swapin:
teardown: swapin:
lookup_swap_cgroup_id()
rcu_read_lock()
mem_cgroup_lookup()
css_tryget()
rcu_read_unlock()
disable css_tryget()
call_rcu()
offline_css()
reparent_charges()
res_counter_charge() (hierarchical!)
css_put()
css_free()
pc->mem_cgroup = dead memcg
add page to dead lru
Add a final reparenting step into css_free() to make sure any such raced
charges are moved out of the memcg before it's finally freed.
In the longer term it would be cleaner to have the css_tryget() and the
res_counter charge under the same RCU lock section so that the charge
reparenting is deferred until the last charge whose tryget succeeded is
visible. But this will require more invasive changes that will be
harder to evaluate and backport into stable, so better defer them to a
separate change set.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
p = mmap((void *) GB, 10 * MB, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
for (i = 0; i < 10 * MB; i += 4096)
p[i] = 1;
mremap(p, 10 * MB, 10 * MB, MREMAP_FIXED | MREMAP_MAYMOVE, 2 * GB);
return 0;
}
Due to split PMD lock, we now store preallocated PTE tables for THP
pages per-PMD table. It means we need to move them to other PMD table
if huge PMD moved there.
mfd/rtc: s5m: fix register updating by adding regmap for RTC
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PM suspend/resume ops to rtc-s5m driver and enable IRQ wake during
suspend so the RTC would act like a wake up source. This allows waking
up from suspend to RAM on RTC alarm interrupt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: s5m: limit endless loop waiting for register update
After setting alarm or time the driver is waiting for UDR register to be
cleared indicating that registers data have been transferred.
Limit the endless loop to only 5 retries.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc: s5m: fix unsuccesful IRQ request during probe
Probe failed for rtc-s5m:
s5m-rtc s5m-rtc: Failed to request alarm IRQ: 12: -22
s5m-rtc: probe of s5m-rtc failed with error -22
Fix rtc-s5m interrupt request by using regmap_irq_get_virq() for mapping
the IRQ.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Acked-by: Sangbeom Kim <sbkim73@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Fri, 13 Dec 2013 01:12:24 +0000 (17:12 -0800)]
include/linux/kernel.h: make might_fault() a nop for !MMU
The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.
This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):
arch/arm/kernel/built-in.o: In function `arch_ptrace':
arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
arch/arm/kernel/built-in.o: In function `restore_sigframe':
arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
...
arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Beulich [Fri, 13 Dec 2013 01:12:22 +0000 (17:12 -0800)]
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
Commit fad1a86e25e0 ("procfs: call default get_unmapped_area on
MMU-present architectures"), as its title says, took care of only the
MMU case, leaving the !MMU side still in the regressed state (returning
-EIO in all cases where pde->proc_fops->get_unmapped_area is NULL).
"Commit c4fe24485729 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file, which
causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file operation
in the procfs file, is not defined"
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: <stable@vger.kernel.org> [3.12.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Dec 2013 01:12:20 +0000 (17:12 -0800)]
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
Commit 84235de394d9 ("fs: buffer: move allocation failure loop into the
allocator") started recognizing __GFP_NOFAIL in memory cgroups but
forgot to disable the OOM killer.
Any task that does not fail allocation will also not enter the OOM
completion path. So don't declare an OOM state in this case or it'll be
leaked and the task be able to bypass the limit until the next
userspace-triggered page fault cleans up the OOM state.
Reported-by: William Dauchy <wdauchy@gmail.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> [3.12.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 13 Dec 2013 01:12:19 +0000 (17:12 -0800)]
include/linux/hugetlb.h: make isolate_huge_page() an inline
With CONFIG_HUGETLBFS=n:
mm/migrate.c: In function `do_move_page_to_node_array':
include/linux/hugetlb.h:140:33: warning: statement with no effect [-Wunused-value]
#define isolate_huge_page(p, l) false
^
mm/migrate.c:1170:4: note: in expansion of macro `isolate_huge_page'
isolate_huge_page(page, &pagelist);
Linus Torvalds [Thu, 12 Dec 2013 23:45:03 +0000 (15:45 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
Again, OMAP regressions due to move to DT is the bulk of the changes
here, but this should be the last of it for 3.13. There are also a
handful of OMAP hwmod changes (power management, reset handling) for
USB on OMAP3 that fixes some longish-standing bugs around USB resets.
There are a couple of other changes that also add up line count a bit:
One is a long-standing bug with the keyboard layout on one of the PXA
platforms. The other is a fix for highbank that moves their
power-off/reset button handling to be done in-kernel since relying on
userspace to handle it was fragile and awkward"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sun6i: dt: Fix interrupt trigger types
ARM: sun7i: dt: Fix interrupt trigger types
MAINTAINERS: merge IMX6 entry into IMX
ARM: tegra: add missing break to fuse initialization code
ARM: pxa: prevent PXA270 occasional reboot freezes
ARM: pxa: tosa: fix keys mapping
ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
ARM: davinci: Fix McASP mem resource names
ARM: highbank: handle soft poweroff and reset key events
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
Linus Torvalds [Thu, 12 Dec 2013 23:25:10 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes. It was rebased this morning, but
I was just fixing signed-off-by tags with the wrong email"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix access_ok() check in btrfs_ioctl_send()
Btrfs: make sure we cleanup all reloc roots if error happens
Btrfs: skip building backref tree for uuid and quota tree when doing balance relocation
Btrfs: fix an oops when doing balance relocation
Btrfs: don't miss skinny extent items on delayed ref head contention
btrfs: call mnt_drop_write after interrupted subvol deletion
Btrfs: don't clear the default compression type
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.
Cc: <stable@vger.kernel.org> # 3.12 Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Paul Moore [Tue, 10 Dec 2013 19:58:01 +0000 (14:58 -0500)]
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
Due to difficulty in arriving at the proper security label for
TCP SYN-ACK packets in selinux_ip_postroute(), we need to check packets
while/before they are undergoing XFRM transforms instead of waiting
until afterwards so that we can determine the correct security label.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Tue, 10 Dec 2013 19:57:54 +0000 (14:57 -0500)]
selinux: look for IPsec labels on both inbound and outbound packets
Previously selinux_skb_peerlbl_sid() would only check for labeled
IPsec security labels on inbound packets, this patch enables it to
check both inbound and outbound traffic for labeled IPsec security
labels.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Wed, 4 Dec 2013 21:10:51 +0000 (16:10 -0500)]
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
In selinux_ip_postroute() we perform access checks based on the
packet's security label. For locally generated traffic we get the
packet's security label from the associated socket; this works in all
cases except for TCP SYN-ACK packets. In the case of SYN-ACK packet's
the correct security label is stored in the connection's request_sock,
not the server's socket. Unfortunately, at the point in time when
selinux_ip_postroute() is called we can't query the request_sock
directly, we need to recreate the label using the same logic that
originally labeled the associated request_sock.
See the inline comments for more explanation.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <pmoore@redhat.com>
Paul Moore [Wed, 4 Dec 2013 21:10:45 +0000 (16:10 -0500)]
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
In selinux_ip_output() we always label packets based on the parent
socket. While this approach works in almost all cases, it doesn't
work in the case of TCP SYN-ACK packets when the correct label is not
the label of the parent socket, but rather the label of the larval
socket represented by the request_sock struct.
Unfortunately, since the request_sock isn't queued on the parent
socket until *after* the SYN-ACK packet is sent, we can't lookup the
request_sock to determine the correct label for the packet; at this
point in time the best we can do is simply pass/NF_ACCEPT the packet.
It must be said that simply passing the packet without any explicit
labeling action, while far from ideal, is not terrible as the SYN-ACK
packet will inherit any IP option based labeling from the initial
connection request so the label *should* be correct and all our
access controls remain in place so we shouldn't have to worry about
information leaks.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Cc: stable@vger.kernel.org Signed-off-by: Paul Moore <pmoore@redhat.com>
Gleb Natapov [Thu, 12 Dec 2013 20:20:08 +0000 (21:20 +0100)]
KVM: x86: fix guest-initiated crash with x2apic (CVE-2013-6376)
A guest can cause a BUG_ON() leading to a host kernel crash.
When the guest writes to the ICR to request an IPI, while in x2apic
mode the following things happen, the destination is read from
ICR2, which is a register that the guest can control.
kvm_irq_delivery_to_apic_fast uses the high 16 bits of ICR2 as the
cluster id. A BUG_ON is triggered, which is a protection against
accessing map->logical_map with an out-of-bounds access and manages
to avoid that anything really unsafe occurs.
The logic in the code is correct from real HW point of view. The problem
is that KVM supports only one cluster with ID 0 in clustered mode, but
the code that has the bug does not take this into account.
Reported-by: Lars Bull <larsbull@google.com> Cc: stable@vger.kernel.org Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andy Honig [Wed, 20 Nov 2013 18:23:22 +0000 (10:23 -0800)]
KVM: x86: Convert vapic synchronization to _cached functions (CVE-2013-6368)
In kvm_lapic_sync_from_vapic and kvm_lapic_sync_to_vapic there is the
potential to corrupt kernel memory if userspace provides an address that
is at the end of a page. This patches concerts those functions to use
kvm_write_guest_cached and kvm_read_guest_cached. It also checks the
vapic_address specified by userspace during ioctl processing and returns
an error to userspace if the address is not a valid GPA.
This is generally not guest triggerable, because the required write is
done by firmware that runs before the guest. Also, it only affects AMD
processors and oldish Intel that do not have the FlexPriority feature
(unless you disable FlexPriority, of course; then newer processors are
also affected).
Fixes: b93463aa59d6 ('KVM: Accelerated apic support') Reported-by: Andrew Honig <ahonig@google.com> Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
projects / linux-beck.git / log