Ido Schimmel [Wed, 17 Aug 2016 14:39:36 +0000 (16:39 +0200)]
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3f4 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:35 +0000 (16:39 +0200)]
mlxsw: spectrum: Add missing rollbacks in error path
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:33 +0000 (16:39 +0200)]
mlxsw: spectrum: Trap loop-backed packets
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Reported-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:31 +0000 (16:39 +0200)]
mlxsw: spectrum: Mark port as active before registering it
Commit bbf2a4757b30 ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b30 ("mlxsw: spectrum: Initialize ports at the end of init sequence") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:30 +0000 (16:39 +0200)]
mlxsw: spectrum: Create PVID vPort before registering netdevice
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:29 +0000 (16:39 +0200)]
mlxsw: spectrum: Remove redundant errors from the code
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:28 +0000 (16:39 +0200)]
mlxsw: spectrum: Don't return upon error in removal path
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: mediatek: fix runtime warning raised by inconsistent struct device pointers passed to DMA API
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: mediatek: fix flow control settings on GMAC0 is not being enabled properly
Commit 08ef55c6f257acf3bdc6940813f80e8f0f5d90ec
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f93b0c3daa9ea35d89ab3a933c7b5a0
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: mediatek: fix RMII mode and add REVMII supported by GMAC
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
I feel like we should maybe return -ENOMEM or -ENOBUFS, but I'm not sure
userspace is equipped to handle that. Anyway, this is better than a GPF
and looks somewhat consistent with other tipc_msg_create() callers.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Aug 2016 20:48:08 +0000 (13:48 -0700)]
Merge branch 'hv_netvsc-VF-removal-fixes'
Vitaly Kuznetsov says:
====================
hv_netvsc: fixes for VF removal path
Kernel crash is reported after VF is removed and detached from netvsc
device. Turns out we have multiple different (but related) issues on the
VF removal path which I'm trying to address with PATCHes 2-5 of this
series. PATCH1 is required to support the change.
Changes since v1:
- Re-arrange patches in the series to not introduce new issues [David Miller]
- Add PATCH5 which fixes a new issue I discovered while testing.
- Add Haiyang' A-b tags to PATCH1-4
With regards to Stephen's suggestion: I believe that switching to using RCU
and eliminating vf_use_cnt/vf_inject is the right thing to do long-term, we
can either put this on top of this series or do it later in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Mon, 15 Aug 2016 15:48:43 +0000 (17:48 +0200)]
hv_netvsc: fix bonding devices check in netvsc_netdev_event()
Bonding driver sets IFF_BONDING on both master (the bonding device) and
slave (the real NIC) devices and in netvsc_netdev_event() we want to skip
master devices only. Currently, there is an uncertainty when a slave
interface is removed: if bonding module comes first in netdev_chain it
clears IFF_BONDING flag on the netdev and netvsc_netdev_event() correctly
handles NETDEV_UNREGISTER event, but in case netvsc comes first on the
chain it sees the device with IFF_BONDING still attached and skips it. As
we still hold vf_netdev pointer to the device we crash on the next inject.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Mon, 15 Aug 2016 15:48:42 +0000 (17:48 +0200)]
hv_netvsc: protect module refcount by checking net_device_ctx->vf_netdev
We're not guaranteed to see NETDEV_REGISTER/NETDEV_UNREGISTER notifications
only once per VF but we increase/decrease module refcount unconditionally.
Check vf_netdev to make sure we don't take/release it twice. We presume
that only one VF per netvsc device may exist.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Mon, 15 Aug 2016 15:48:41 +0000 (17:48 +0200)]
hv_netvsc: reset vf_inject on VF removal
We reset vf_inject on VF going down (netvsc_vf_down()) but we don't on
VF removal (netvsc_unregister_vf()) so vf_inject stays 'true' while
vf_netdev is already NULL and we're trying to inject packets into NULL
net device in netvsc_recv_callback() causing kernel to crash.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Mon, 15 Aug 2016 15:48:40 +0000 (17:48 +0200)]
hv_netvsc: avoid deadlocks between rtnl lock and vf_use_cnt wait
Here is a deadlock scenario:
- netvsc_vf_up() schedules netvsc_notify_peers() work and quits.
- netvsc_vf_down() runs before netvsc_notify_peers() gets executed. As it
is being executed from netdev notifier chain we hold rtnl lock when we
get here.
- we enter while (atomic_read(&net_device_ctx->vf_use_cnt) != 0) loop and
wait till netvsc_notify_peers() drops vf_use_cnt.
- netvsc_notify_peers() starts on some other CPU but netdev_notify_peers()
will hang on rtnl_lock().
- deadlock!
Instead of introducing additional synchronization I suggest we drop
gwrk.dwrk completely and call NETDEV_NOTIFY_PEERS directly. As we're
acting under rtnl lock this is legitimate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Mon, 15 Aug 2016 15:48:39 +0000 (17:48 +0200)]
hv_netvsc: don't lose VF information
struct netvsc_device is not suitable for storing VF information as this
structure is being destroyed on MTU change / set channel operation (see
rndis_filter_device_remove()). Move all VF related stuff to struct
net_device_context which is persistent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Mon, 15 Aug 2016 11:06:24 +0000 (13:06 +0200)]
gre: set inner_protocol on xmit
Ensure that the inner_protocol is set on transmit so that GSO segmentation,
which relies on that field, works correctly.
This is achieved by setting the inner_protocol in gre_build_header rather
than each caller of that function. It ensures that the inner_protocol is
set when gre_fb_xmit() is used to transmit GRE which was not previously the
case.
I have observed this is not the case when OvS transmits GRE using
lwtunnel metadata (which it always does).
Fixes: 38720352412a ("gre: Use inner_proto to obtain inner header protocol") Cc: Pravin Shelar <pshelar@ovn.org> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Fri, 12 Aug 2016 16:13:38 +0000 (01:13 +0900)]
net: ipv6: Fix ping to link-local addresses.
ping_v6_sendmsg does not set flowi6_oif in response to
sin6_scope_id or sk_bound_dev_if, so it is not possible to use
these APIs to ping an IPv6 address on a different interface.
Instead, it sets flowi6_iif, which is incorrect but harmless.
Stop setting flowi6_iif, and support various ways of setting oif
in the same priority order used by udpv6_sendmsg.
Tested: https://android-review.googlesource.com/#/c/254470/ Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
roundup_pow_of_two() is undefined when called with an argument of 0, so
let's avoid the call and just fall back to ht->p.min_size (which should
never be smaller than HASH_MIN_SIZE).
Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent [Sun, 14 Aug 2016 13:38:29 +0000 (15:38 +0200)]
mlxsw: spectrum_router: Fix use after free
In mlxsw_sp_router_fib4_add_info_destroy(), the fib_entry pointer is used
after it has been freed by mlxsw_sp_fib_entry_destroy(). Use a temporary
variable to fix this.
Fixes: 61c503f976b5449e ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: Jiri Pirko <jiri@mellanox.com> Acked-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The failure happens when allocating the spinlock array.
Even with GFP_KERNEL its unlikely for such a large allocation
to succeed.
Thomas Graf pointed me at inet_ehash_locks_alloc(), so in addition
to adding NOWARN for atomic allocations this also makes the bucket-array
sizing more conservative.
In commit 095dc8e0c3686 ("tcp: fix/cleanup inet_ehash_locks_alloc()"),
Eric Dumazet says: "Budget 2 cache lines per cpu worth of 'spinlocks'".
IOW, consider size needed by a single spinlock when determining
number of locks per cpu. So with 64 byte per cacheline and 4 byte per
spinlock this gives 32 locks per cpu.
Resulting size of the lock-array (sizeof(spinlock) == 4):
Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Suggested-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 12 Aug 2016 14:10:33 +0000 (16:10 +0200)]
net: remove type_check from dev_get_nest_level()
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Fri, 12 Aug 2016 11:02:38 +0000 (12:02 +0100)]
net: ipv6: Do not keep IPv6 addresses when IPv6 is disabled
If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Signed-off-by: Mike Manning <mmanning@brocade.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should initialize sctp_ht_iter::start_fail to zero if ->start()
succeeds, otherwise it's possible that we leave an old value of 1 there,
which will cause ->stop() to not call sctp_transport_walk_stop(), which
causes all sorts of problems like not calling rcu_read_unlock() (and
preempt_enable()), eventually leading to more warnings like this:
BUG: sleeping function called from invalid context at mm/slab.h:388
in_atomic(): 0, irqs_disabled(): 0, pid: 16551, name: trinity-c2
Preemption disabled at:[<ffffffff819bceb6>] rhashtable_walk_start+0x46/0x150
Notice that this is a subtly different stacktrace from the one in commit 5fc382d875 ("net/sctp: terminate rhashtable walk correctly").
Cc: Xin Long <lucien.xin@gmail.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Acked-By: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If iriap_register_lsap() fails to allocate memory, self->lsap is
set to NULL. However, none of the callers handle the failure and
irlmp_connect_request() will happily dereference it:
There's more problems with missing error checks in iriap_init() (and
indeed all of irda_init()), but that's a bigger problem that needs
very careful review and testing. This patch will fix the most serious
bug (as it's easily reached from unprivileged userspace).
I have tested my patch with a reproducer.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 12 Aug 2016 05:48:21 +0000 (07:48 +0200)]
ipv6: suppress sparse warnings in IP6_ECN_set_ce()
Pass the correct type __wsum to csum_sub() and csum_add(). This doesn't
really change anything since __wsum really *is* __be32, but removes the
address space warnings from sparse.
Cc: Eric Dumazet <edumazet@google.com> Fixes: 34ae6a1aa054 ("ipv6: update skb->csum when CE mark is propagated") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 11 Aug 2016 19:38:37 +0000 (21:38 +0200)]
bpf: fix write helpers with regards to non-linear parts
Fix the bpf_try_make_writable() helper and all call sites we have in BPF,
it's currently defect with regards to skbs when the write_len spans into
non-linear parts, no matter if cloned or not.
There are multiple issues at once. First, using skb_store_bits() is not
correct since even if we have a cloned skb, page frags can still be shared.
To really make them private, we need to pull them in via __pskb_pull_tail()
first, which also gets us a private head via pskb_expand_head() implicitly.
This is for helpers like bpf_skb_store_bytes(), bpf_l3_csum_replace(),
bpf_l4_csum_replace(). Really, the only thing reasonable and working here
is to call skb_ensure_writable() before any write operation. Meaning, via
pskb_may_pull() it makes sure that parts we want to access are pulled in and
if not does so plus unclones the skb implicitly. If our write_len still fits
the headlen and we're cloned and our header of the clone is not writable,
then we need to make a private copy via pskb_expand_head(). skb_store_bits()
is a bit misleading and only safe to store into non-linear data in different
contexts such as 357b40a18b04 ("[IPV6]: IPV6_CHECKSUM socket option can
corrupt kernel memory").
For above BPF helper functions, it means after fixed bpf_try_make_writable(),
we've pulled in enough, so that we operate always based on skb->data. Thus,
the call to skb_header_pointer() and skb_store_bits() becomes superfluous.
In bpf_skb_store_bytes(), the len check is unnecessary too since it can
only pass in maximum of BPF stack size, so adding offset is guaranteed to
never overflow. Also bpf_l3/4_csum_replace() helpers must test for proper
offset alignment since they use __sum16 pointer for writing resulting csum.
The remaining helpers that change skb data not discussed here yet are
bpf_skb_vlan_push(), bpf_skb_vlan_pop() and bpf_skb_change_proto(). The
vlan helpers internally call either skb_ensure_writable() (pop case) and
skb_cow_head() (push case, for head expansion), respectively. Similarly,
bpf_skb_proto_xlat() takes care to not mangle page frags.
Fixes: 608cd71a9c7c ("tc: bpf: generalize pedit action") Fixes: 91bc4822c3d6 ("tc: bpf: add checksum helpers") Fixes: 3697649ff29e ("bpf: try harder on clones when writing into skb") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 11 Aug 2016 17:17:22 +0000 (18:17 +0100)]
calipso: fix resource leak on calipso_genopt failure
Currently, if calipso_genopt fails then the error exit path
does not free the ipv6_opt_hdr new causing a memory leak. Fix
this by kfree'ing new on the error exit path.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 12 Aug 2016 20:17:17 +0000 (22:17 +0200)]
bpf: fix bpf_skb_in_cgroup helper naming
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Arnd Bergmann [Wed, 10 Aug 2016 21:54:08 +0000 (23:54 +0200)]
dsa: mv88e6xxx: hide unused functions
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 57d3231057e9 ("net: dsa: mv88e6xxx: fix style issues") Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 11 Aug 2016 13:24:27 +0000 (15:24 +0200)]
macsec: use after free when deleting the underlying device
macsec_notify() loops over the list of macsec devices configured on the
underlying device when this device is being removed. This list is part
of the rx_handler data.
However, macsec_dellink unregisters the rx_handler and frees the
rx_handler data when the last macsec device is removed from the
underlying device.
Add macsec_common_dellink() to delete macsec devices without
unregistering the rx_handler and freeing the associated data.
Fixes: 960d5848dbf1 ("macsec: fix memory leaks around rx_handler (un)registration") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 11 Aug 2016 10:15:56 +0000 (18:15 +0800)]
macvtap: fix use after free for skb_array during release
We've clean skb_array in macvtap_put_queue() but still try to pop from
it during macvtap_sock_destruct(). Fix this use after free by moving
the skb array cleanup to macvtap_sock_destruct() instead.
Fixes: 362899b8725b ("macvtap: switch to use skb array") Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com> Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
openvswitch: do not ignore netdev errors when creating tunnel vports
The creation of a tunnel vport (geneve, gre, vxlan) brings up a
corresponding netdev, a multi-step operation which can fail.
For example, changing a vxlan vport's netdev state to 'up' binds the
vport's socket to a UDP port - if the binding fails (e.g. due to the
port being in use), the error is currently ignored giving the
appearance that the tunnel vport creation completed successfully.
Signed-off-by: Martynas Pumputis <martynas@weave.works> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cf6f7e1d5109 ("tipc: dump monitor attributes"),
I dereferenced a pointer before checking if its valid.
This is reported by static check Smatch as:
net/tipc/monitor.c:733 tipc_nl_add_monitor_peer()
warn: variable dereferenced before check 'mon' (see line 731)
In this commit, we check for a valid monitor before proceeding
with any other operation.
Fixes: cf6f7e1d5109 ("tipc: dump monitor attributes") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Thu, 4 Aug 2016 02:11:19 +0000 (11:11 +0900)]
bridge: Fix problems around fdb entries pointing to the bridge device
Adding fdb entries pointing to the bridge device uses fdb_insert(),
which lacks various checks and does not respect added_by_user flag.
As a result, some inconsistent behavior can happen:
* Adding temporary entries succeeds but results in permanent entries.
* Same goes for "dynamic" and "use".
* Changing mac address of the bridge device causes deletion of
user-added entries.
* Replacing existing entries looks successful from userspace but actually
not, regardless of NLM_F_EXCL flag.
Use the same logic as other entries and fix them.
Fixes: 3741873b4f73 ("bridge: allow adding of fdb entries pointing to the bridge device") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wenyou Yang [Fri, 5 Aug 2016 06:35:41 +0000 (14:35 +0800)]
net: phy: micrel: Add specific suspend
Disable all interrupts when suspend, they will be enabled
when resume. Otherwise, the suspend/resume process will be
blocked occasionally.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dm9000: Fix irq trigger type setup on non-dt platforms
Commit b5a099c67a1c36b "net: ethernet: davicom: fix devicetree irq
resource" causes an interrupt storm after the ethernet interface
is activated on S3C24XX platform (ARM non-dt), due to the interrupt
trigger type not being set properly.
It seems, after adding parsing of IRQ flags in commit 7085a7401ba54e92b
"drivers: platform: parse IRQ flags from resources", there is no path
for non-dt platforms where irq_set_type callback could be invoked when
we don't pass the trigger type flags to the request_irq() call.
In case of a board where the regression is seen the interrupt trigger
type flags are passed through a platform device's resource and it is
not currently handled properly without passing the irq trigger type
flags to the request_irq() call. In case of OF an of_irq_get() call
within platform_get_irq() function seems to be ensuring required irq_chip
setup, but there is no equivalent code for non OF/ACPI platforms.
This patch mostly restores irq trigger type setting code which has been
removed in commit ("net: ethernet: davicom: fix devicetree irq resource").
Fixes: b5a099c67a1c36b913 ("net: ethernet: davicom: fix devicetree irq resource") Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: cpsw: fix kmemleak false-positive reports for sk buffers
Kmemleak reports following false positive memory leaks for each sk
buffers allocated by CPSW (__netdev_alloc_skb_ip_align()) in
cpsw_ndo_open() and cpsw_rx_handler():
This happens because CPSW allocates SK buffers and then passes
pointers on them in CPDMA where they stored in internal CPPI RAM
(SRAM) which belongs to DEV MMIO space. Kmemleak does not scan IO
memory and so reports memory leaks.
Hence, mark allocated sk buffers as false positive explicitly.
Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vti: flush x-netns xfrm cache when vti interface is removed
When executing the script included below, the netns delete operation
hangs with the following message (repeated at 10 second intervals):
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 1
This occurs because a reference to the lo interface in the "secure" netns
is still held by a dst entry in the xfrm bundle cache in the init netns.
Address this problem by garbage collecting the tunnel netns flow cache
when a cross-namespace vti interface receives a NETDEV_DOWN notification.
A more detailed description of the problem scenario (referencing commands
in the script below):
(1) ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
The vti_test interface is created in the init namespace. vti_tunnel_init()
attaches a struct ip_tunnel to the vti interface's netdev_priv(dev),
setting the tunnel net to &init_net.
(2) ip link set vti_test netns secure
The vti_test interface is moved to the "secure" netns. Note that
the associated struct ip_tunnel still has tunnel->net set to &init_net.
Note that tunnel->net is the init namespace, while skb_dst(skb) references
the vti_test interface in the "secure" namespace. The returned dst
references an interface in the init namespace.
Also note that the first parameter to xfrm_lookup() determines which flow
cache is used to store the computed xfrm bundle, so after xfrm_lookup()
returns there will be a cached bundle in the init namespace flow cache
with a dst referencing a device in the "secure" namespace.
(4) ip netns del secure
Kernel begins to delete the "secure" namespace. At some point the
vti_test interface is deleted, at which point dst_ifdown() changes
the dst->dev in the cached xfrm bundle flow from vti_test to lo (still
in the "secure" namespace however).
Since nothing has happened to cause the init namespace's flow cache
to be garbage collected, this dst remains attached to the flow cache,
so the kernel loops waiting for the last reference to lo to go away.
<Begin script>
ip link add br1 type bridge
ip link set dev br1 up
ip addr add dev br1 1.1.1.1/8
ip netns add secure
ip link add vti_test type vti local 1.1.1.1 remote 1.1.1.2 key 1
ip link set vti_test netns secure
ip netns exec secure ip link set vti_test up
ip netns exec secure ip link s lo up
ip netns exec secure ip addr add dev lo 192.168.100.1/24
ip netns exec secure ip route add 192.168.200.0/24 dev vti_test
ip xfrm policy flush
ip xfrm state flush
ip xfrm policy add dir out tmpl src 1.1.1.1 dst 1.1.1.2 \
proto esp mode tunnel mark 1
ip xfrm policy add dir in tmpl src 1.1.1.2 dst 1.1.1.1 \
proto esp mode tunnel mark 1
ip xfrm state add src 1.1.1.1 dst 1.1.1.2 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
ip xfrm state add src 1.1.1.2 dst 1.1.1.1 proto esp spi 1 \
mode tunnel enc des3_ede 0x112233445566778811223344556677881122334455667788
Reported-by: Hangbin Liu <haliu@redhat.com> Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Lance Richardson <lrichard@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 9 Aug 2016 10:30:43 +0000 (11:30 +0100)]
rxrpc: Fix a use-after-push in data_ready handler
Fix a use of a packet after it has been enqueued onto the packet processing
queue in the data_ready handler. Once on a call's Rx queue, we mustn't
touch it any more as it may be dequeued and freed by the call processor
running on a work queue.
Save the values we need before enqueuing.
Without this, we can get an oops like the following:
David Howells [Tue, 9 Aug 2016 09:11:48 +0000 (10:11 +0100)]
rxrpc: Once packet posted in data_ready, don't retry posting
Once a packet has been posted to a connection in the data_ready handler, we
mustn't try reposting if we then find that the connection is dying as the
refcount has been given over to the dying connection and the packet might
no longer exist.
Losing the packet isn't a problem as the peer will retransmit.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 8 Aug 2016 09:27:26 +0000 (10:27 +0100)]
rxrpc: Don't access connection from call if pointer is NULL
The call state machine processor sets up the message parameters for a UDP
message that it might need to transmit in advance on the basis that there's
a very good chance it's going to have to transmit either an ACK or an
ABORT. This requires it to look in the connection struct to retrieve some
of the parameters.
However, if the call is complete, the call connection pointer may be NULL
to dissuade the processor from transmitting a message. However, there are
some situations where the processor is still going to be called - and it's
still going to set up message parameters whether it needs them or not.
This results in a NULL pointer dereference at:
net/rxrpc/call_event.c:837
To fix this, skip the message pre-initialisation if there's no connection
attached.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 8 Aug 2016 12:06:41 +0000 (13:06 +0100)]
rxrpc: Need to flag call as being released on connect failure
If rxrpc_new_client_call() fails to make a connection, the call record that
it allocated needs to be marked as RXRPC_CALL_RELEASED before it is passed
to rxrpc_put_call() to indicate that it no longer has any attachment to the
AF_RXRPC socket.
Without this, an assertion failure may occur at:
net/rxrpc/call_object:635
Signed-off-by: David Howells <dhowells@redhat.com>
Arnd Bergmann [Mon, 8 Aug 2016 10:13:45 +0000 (12:13 +0200)]
rxrpc: fix uninitialized pointer dereference in debug code
A newly added bugfix caused an uninitialized variable to be
used for printing debug output. This is harmless as long
as the debug setting is disabled, but otherwise leads to an
immediate crash.
gcc warns about this when -Wmaybe-uninitialized is enabled:
net/rxrpc/call_object.c: In function 'rxrpc_release_call':
net/rxrpc/call_object.c:496:163: error: 'sp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The initialization was removed but one of the users remains.
This adds back the initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 372ee16386bb ("rxrpc: Fix races between skb free, ACK generation and replying") Signed-off-by: David Howells <dhowells@redhat.com>
Liping Zhang [Mon, 8 Aug 2016 14:10:26 +0000 (22:10 +0800)]
netfilter: ctnetlink: reject new conntrack request with different l4proto
Currently, user can add a conntrack with different l4proto via nfnetlink.
For example, original tuple is TCP while reply tuple is SCTP. This is
invalid combination, we should report EINVAL to userspace.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Mon, 8 Aug 2016 14:07:27 +0000 (22:07 +0800)]
netfilter: nfnetlink_queue: reject verdict request from different portid
Like NFQNL_MSG_VERDICT_BATCH do, we should also reject the verdict
request when the portid is not same with the initial portid(maybe
from another process).
Liping Zhang [Mon, 8 Aug 2016 14:03:40 +0000 (22:03 +0800)]
netfilter: nfnetlink_queue: fix memory leak when attach expectation successfully
User can use NFQA_EXP to attach expectations to conntracks, but we
forget to put back nf_conntrack_expect when it is inserted successfully,
i.e. in this normal case, expect's use refcnt will be 3. So even we
unlink it and put it back later, the use refcnt is still 1, then the
memory will be leaked forever.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Mon, 8 Aug 2016 13:57:58 +0000 (21:57 +0800)]
netfilter: nf_ct_expect: remove the redundant slash when policy name is empty
The 'name' filed in struct nf_conntrack_expect_policy{} is not a
pointer, so check it is NULL or not will always return true. Even if the
name is empty, slash will always be displayed like follows:
# cat /proc/net/nf_conntrack_expect
297 l3proto = 2 proto=6 src=1.1.1.1 dst=2.2.2.2 sport=1 dport=1025 ftp/
^
Fixes: 3a8fc53a45c4 ("netfilter: nf_ct_helper: allocate 16 bytes for the helper and policy names") Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
qed: Update app count when adding a new dcbx app entry to the table.
App count is not updated while adding new app entry to the dcbx app table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add dcbx app support for IEEE Selection Field.
MFW now supports the Selection field for IEEE mode. Add driver changes to
use the newer MFW masks to read/write the port-id value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Use ieee mfw-mask to get ethtype in ieee-dcbx mode.
Ethtype value is being read incorrectly in ieee-dcbx mode. Use the
correct mfw mask value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Remove the endian-ness conversion for pri_to_tc value.
Endian-ness conversion is not needed for priority-to-TC field as the
field is already being read/written by the driver in big-endian way.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 7 Aug 2016 06:15:13 +0000 (14:15 +0800)]
sctp: use event->chunk when it's valid
Commit 52253db924d1 ("sctp: also point GSO head_skb to the sk when
it's available") used event->chunk->head_skb to get the head_skb in
sctp_ulpevent_set_owner().
But at that moment, the event->chunk was NULL, as it cloned the skb
in sctp_ulpevent_make_rcvmsg(). Therefore, that patch didn't really
work.
This patch is to move the event->chunk initialization before calling
sctp_ulpevent_receive_data() so that it uses event->chunk when it's
valid.
Fixes: 52253db924d1 ("sctp: also point GSO head_skb to the sk when it's available") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Sat, 6 Aug 2016 00:45:37 +0000 (17:45 -0700)]
net: vxlan: lwt: Fix vxlan local traffic.
vxlan driver has bypass for local vxlan traffic, but that
depends on information about all VNIs on local system in
vxlan driver. This is not available in case of LWT.
Therefore following patch disable encap bypass for LWT
vxlan traffic.
Fixes: ee122c79d42 ("vxlan: Flow based tunneling"). Reported-by: Jakub Libosvar <jlibosva@redhat.com> Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Sat, 6 Aug 2016 00:45:36 +0000 (17:45 -0700)]
net: vxlan: lwt: Use source ip address during route lookup.
LWT user can specify destination as well as source ip address
for given tunnel endpoint. But vxlan is ignoring given source
ip address. Following patch uses both ip address to route the
tunnel packet. This consistent with other LWT implementations,
like GENEVE and GRE.
Fixes: ee122c79d42 ("vxlan: Flow based tunneling"). Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:13 +0000 (00:11 +0200)]
bpf: fix checksum for vlan push/pop helper
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60d9 ("bpf: introduce bpf_skb_vlan_push/pop() helpers") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:12 +0000 (00:11 +0200)]
bpf: fix checksum fixups on bpf_skb_store_bytes
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c7c ("tc: bpf: generalize pedit action") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 4 Aug 2016 22:11:11 +0000 (00:11 +0200)]
bpf: also call skb_postpush_rcsum on xmit occasions
Follow-up to commit f8ffad69c9f8 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9f8 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4d4 ("bpf: introduce bpf_clone_redirect() helper") Fixes: 27b29f63058d ("bpf: add bpf_redirect() helper") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
...leading to the following warning for !DEBUG builds:
drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
static void dump_eth_one(struct net_device *dev)
^
...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig
Put the function definition under the same #ifdef as the call site
to avoid the warning.
Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 4 Aug 2016 14:36:22 +0000 (17:36 +0300)]
mlxsw: spectrum: Add missing DCB rollback in error path
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b42 ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 4 Aug 2016 14:36:21 +0000 (17:36 +0300)]
mlxsw: spectrum: Do not override PAUSE settings
The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).
Fix this by packing the PFCC register with the current PAUSE settings.
Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.
Fixes: d81a6bdb87ce ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1aa661f5c3df1 ("rhashtable-test: Measure time to insert, remove & traverse entries") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 4 Aug 2016 10:11:57 +0000 (12:11 +0200)]
sctp_diag: Respect ss adding TCPF_CLOSE to idiag_states
Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 4 Aug 2016 10:11:56 +0000 (12:11 +0200)]
sctp_diag: Fix T3_rtx timer export
The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.
Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack_sip: CSeq 0 is a valid CSeq
Do not drop packet when CSeq is 0 as 0 is also a valid value for CSeq.
simple_strtoul() will return 0 either when all digits are 0
or if there are no digits at all. Therefore when simple_strtoul()
returns 0 we check if first character is digit 0 or not.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_rbtree: ignore inactive matching element with no descendants
If we find a matching element that is inactive with no descendants, we
jump to the found label, then crash because of nul-dereference on the
left branch.
Fix this by checking that the element is active and not an interval end
and skipping the logic that only applies to the tree iteration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Tested-by: Anders K. Pedersen <akp@akp.dk>
netfilter: nf_ct_h323: do not re-activate already expired timer
Commit 96d1327ac2e3 ("netfilter: h323: Use mod_timer instead of
set_expect_timeout") just simplify the source codes
if (!del_timer(&exp->timeout))
return 0;
add_timer(&exp->timeout);
to mod_timer(&exp->timeout, jiffies + info->timeout * HZ);
This is not correct, and introduce a race codition:
CPU0 CPU1
- timer expire
process_rcf expectation_timed_out
lock(exp_lock) -
find_exp waiting exp_lock...
re-activate timer!! waiting exp_lock...
unlock(exp_lock) lock(exp_lock)
- unlink expect
- free(expect)
- unlock(exp_lock)
So when the timer expires again, we will access the memory that
was already freed.
Replace mod_timer with mod_timer_pending here to fix this problem.
Fixes: 96d1327ac2e3 ("netfilter: h323: Use mod_timer instead of set_expect_timeout") Cc: Gao Feng <fgao@ikuai8.com> Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Sun, 7 Aug 2016 00:52:00 +0000 (20:52 -0400)]
Merge tag 'mac80211-for-davem-2016-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
... prepare new_value on stack ...
bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.
The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: b53: Add missing ULL suffix for 64-bit constant
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6fbed8f ("net: dsa: b53: Implement ARL add/del/dump operations") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Forster <dforster@brocade.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 3 Aug 2016 13:11:40 +0000 (14:11 +0100)]
rxrpc: Fix races between skb free, ACK generation and replying
Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.
Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released. The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb. ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.
To this end, the following changes are made:
(1) kernel_rxrpc_data_consumed() is added. This should be called whenever
an skb is emptied so as to crank the ACK and call states. This does
not release the skb, however. kernel_rxrpc_free_skb() must now be
called to achieve that. These together replace
rxrpc_kernel_data_delivered().
(2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().
This makes afs_deliver_to_call() easier to work as the skb can simply
be discarded unconditionally here without trying to work out what the
return value of the ->deliver() function means.
The ->deliver() functions can, via afs_data_complete(),
afs_transfer_reply() and afs_extract_data() mark that an skb has been
consumed (thereby cranking the state) without the need to
conditionally free the skb to make sure the state is correct on an
incoming call for when the call processor tries to send the reply.
(3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
has finished with a packet and MSG_PEEK isn't set.
(4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().
Because of this, we no longer need to clear the destructor and put the
call before we free the skb in cases where we don't want the ACK/call
state to be cranked.
(5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
the delivery function already), and the caller is now responsible for
producing an abort if that was the last packet.
(6) There are many bits of unmarshalling code where:
ret = afs_extract_data(call, skb, last, ...);
switch (ret) {
case 0: break;
case -EAGAIN: return 0;
default: return ret;
}
is to be found. As -EAGAIN can now be passed back to the caller, we
now just return if ret < 0:
ret = afs_extract_data(call, skb, last, ...);
if (ret < 0)
return ret;
(7) Checks for trailing data and empty final data packets has been
consolidated as afs_data_complete(). So:
if (skb->len > 0)
return -EBADMSG;
if (!last)
return 0;
becomes:
ret = afs_data_complete(call, skb, last);
if (ret < 0)
return ret;
(8) afs_transfer_reply() now checks the amount of data it has against the
amount of data desired and the amount of data in the skb and returns
an error to induce an abort if we don't get exactly what we want.
Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:
This doesn't have an immediate effect, but can mess up later
LL_RESERVED_SPACE calculations, such as done in
net/ipv6/mcast.c:mld_newpack. For reference, this issue was found
from a skb_panic raised there after the length calculations had given
the wrong result.
Note the other current users of this interface
(drivers/net/tun.c:tun_set_headroom and
drivers/net/veth.c:veth_set_rx_headroom) are both checking this
correctly thus need no modification.
Thanks to Ben for some pointers from the crash dumps!
Cc: Benjamin Poirier <bpoirier@suse.com> Cc: Paolo Abeni <pabeni@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1361414 Signed-off-by: Ian Wienand <iwienand@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Altshul [Thu, 4 Aug 2016 12:43:04 +0000 (15:43 +0300)]
mac80211: Add ieee80211_hw pointer to get_expected_throughput
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Masashi Honma [Tue, 2 Aug 2016 08:16:57 +0000 (17:16 +0900)]
mac80211: End the MPSP even if EOSP frame was not acked
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 2 Aug 2016 09:13:41 +0000 (11:13 +0200)]
mac80211: fix purging multicast PS buffer queue
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>