Ian Campbell [Fri, 19 Aug 2011 06:25:00 +0000 (06:25 +0000)]
net: add APIs for manipulating skb page fragments.
The primary aim is to add skb_frag_(ref|unref) in order to remove the use of
bare get/put_page on SKB pages fragments and to isolate users from subsequent
changes to the skb_frag_t data structure.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Boot [Mon, 22 Aug 2011 20:38:38 +0000 (21:38 +0100)]
firewire: sbp2: fix panic after rmmod with slow targets
If firewire-sbp2 starts a login to a target that doesn't complete ORBs
in a timely manner (and has to retry the login), and the module is
removed before the operation times out, you end up with a null-pointer
dereference and a kernel panic.
[SR: This happens because sbp2_target_get/put() do not maintain
module references. scsi_device_get/put() do, but at occasions like
Chris describes one, nobody holds a reference to an SBP-2 sdev.]
This patch cancels pending work for each unit in sbp2_remove(), which
hopefully means there are no extra references around that prevent us
from unloading. This fixes my crash.
Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Dong Aisheng <b29396@freescale.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dong Aisheng [Sun, 21 Aug 2011 15:45:40 +0000 (23:45 +0800)]
ASoC: mxs-saif: clear clk gate first before register setting
Saif needs clear clk gate first before writing registers or the write
will not success.
The original xx_get_mclk function clear clk gate after mclk setting
that may cause the former mclk setting unwork, then the real output
mclk maybe inaccurate.
Placing the clear before setting mclk to avoid such an issue.
We also have to clear clk gate in startup instead of in prepare function.
Signed-off-by: Dong Aisheng <b29396@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first change is to add an of_node_put, since codec_np has previously
been allocated. The rest of the patch reorganizes the error handling code
so the only code executed is that which is needed.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Alexander Sverdlin <subaparts@yandex.ru> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Timur Tabi [Mon, 22 Aug 2011 14:22:41 +0000 (09:22 -0500)]
sound/soc/fsl/fsl_dma.c: add missing of_node_put
of_parse_phandle increments the reference count of np, so this should be
decremented before trying the next possibility.
Since we don't actually use np, we can decrement the reference count
immediately.
Reported-by: Julia Lawall <julia@diku.dk> Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code really requires the current source directory to be in the
header search path. We already do this if building with an object
tree separate from the source, but it needs to be added manually
if building inside the source. The cflags addition for it accidentally
got removed when collapsing the xfs directory structure.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Alex Elder <aelder@sgi.com>
Kumar Gala [Thu, 4 Aug 2011 08:13:10 +0000 (03:13 -0500)]
drivers/serial/ucc_uart.c: Fix compiler warning
drivers/tty/serial/ucc_uart.c: In function 'qe2cpu_addr':
drivers/tty/serial/ucc_uart.c:238:2: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavan Savoy [Wed, 10 Aug 2011 15:18:37 +0000 (10:18 -0500)]
drivers:misc: ti-st: fix unexpected UART close
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.
Pavan Savoy [Wed, 10 Aug 2011 15:18:36 +0000 (10:18 -0500)]
drivers:misc: ti-st: free skb on firmware download
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Pavan Savoy [Wed, 10 Aug 2011 15:18:35 +0000 (10:18 -0500)]
drivers:misc: ti-st: wait for completion at fail
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Pavan Savoy [Wed, 10 Aug 2011 15:18:34 +0000 (10:18 -0500)]
drivers:misc: ti-st: reinit completion before send
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Vijay Badawadagi [Wed, 10 Aug 2011 15:18:33 +0000 (10:18 -0500)]
drivers:misc: ti-st: fail-safe on wrong pkt type
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Pavan Savoy [Wed, 10 Aug 2011 15:18:32 +0000 (10:18 -0500)]
drivers:misc: ti-st: reinit completion on ver read
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Pavan Savoy [Wed, 10 Aug 2011 15:18:31 +0000 (10:18 -0500)]
drivers:misc:ti-st: platform hooks for chip states
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Pavan Savoy [Wed, 10 Aug 2011 15:18:30 +0000 (10:18 -0500)]
drivers:misc: ti-st: avoid a misleading dbg msg
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
base/devres.c: quiet sparse noise about context imbalance
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Heiko Carstens [Tue, 2 Aug 2011 08:08:34 +0000 (10:08 +0200)]
pti: add missing CONFIG_PCI dependency
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Dmitry Artamonow [Fri, 12 Aug 2011 20:41:11 +0000 (16:41 -0400)]
hwmon: (w83627ehf) add caseopen detection
Export caseopen alarm status into userspace for Winbond W83627*
and Nuvoton NCT677[56] chips and implement alarm clear attribute.
Second caseopen alarm on NCT6776 is also supported.
Guenter Roeck [Tue, 16 Aug 2011 15:15:26 +0000 (08:15 -0700)]
hwmon: (ntc_thermistor) Simplify if sequence
Replace unnecessary if with else statement.
This fixes the following (false) compile warning reported with some combinations
of C compiler version and configuration.
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here
drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here
drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in
this function
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
Andrew Bird [Tue, 16 Aug 2011 23:20:03 +0000 (00:20 +0100)]
USB option driver K3765/K4505 avoid CDC_DATA interface
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
projects / karo-tx-linux.git / log