Guenter Roeck [Wed, 27 Feb 2013 19:41:41 +0000 (11:41 -0800)]
misc/vmw_vmci: Add dependency on CONFIG_NET
Building the vmw_vmci driver with CONFIG_NET undefined results in:
drivers/built-in.o: In function `__qp_memcpy_from_queue.isra.13':
vmci_queue_pair.c:(.text+0x1671a8): undefined reference to `memcpy_toiovec'
drivers/built-in.o: In function `__qp_memcpy_to_queue.isra.14':
vmci_queue_pair.c:(.text+0x167341): undefined reference to `memcpy_fromiovec'
make[1]: [vmlinux] Error 1 (ignored)
since memcpy_toiovec and memcpy_fromiovec are defined in the networking code.
Add the missing dependency.
Gabor Juhos [Fri, 29 Mar 2013 14:52:27 +0000 (15:52 +0100)]
rt2x00: rt2x00pci: fix build error on Ralink RT3x5x SoCs
The rt2800pci driver supports the built-in wireless
MAC of the Ralink RT3x5x SoCs. However building the
driver for these SoCs leads to the following error:
LD init/built-in.o
drivers/built-in.o: In function `rt2800pci_rxdone_tasklet':
<...>/drivers/net/wireless/rt2x00/rt2800pci.c:1012: undefined reference to `rt2x00pci_rxdone'
drivers/built-in.o:(.rodata+0x4780): undefined reference to `rt2x00pci_initialize'
drivers/built-in.o:(.rodata+0x4784): undefined reference to `rt2x00pci_uninitialize'
drivers/built-in.o:(.rodata+0x47bc): undefined reference to `rt2x00pci_flush_queue'
drivers/built-in.o:(.rodata+0x4818): undefined reference to `rt2x00pci_regbusy_read'
make[5]: *** [vmlinux] Error 1
The missing functions are provided by the rt2x00pci
module. This module is only selected by the rt2800pci
driver if PCI support is enabled in the kernel, because
some parts of the rt2x00pci code depends on PCI support.
PCI support is not available on the RT3x5x SoCs because
those have no PCI host controller at all.
Move the non PCI specific code from rt2x00pci into a
separate module. This makes it possible to use that
code even if PCI support is disabled. The affected
functions are used by all of the rt2x00 PCI drivers
so select the new module for those drivers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tim Gardner [Mon, 18 Feb 2013 19:56:28 +0000 (12:56 -0700)]
rt2x00: rt2x00pci_regbusy_read() - only print register access failure once
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: users@rt2x00.serialmonkey.com Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Robert Shade [Tue, 2 Apr 2013 23:52:45 +0000 (19:52 -0400)]
ath9k: Re-enable interrupts after a channel change failure
ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call. Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.
Franky Lin [Tue, 2 Apr 2013 19:06:20 +0000 (21:06 +0200)]
brcmfmac: do not proceed if fail to download nvram to dongle
Nvram contains critical initialization parameter for firmware to run. Host
driver should not proceed if nvram fails to be downloaded to dongle.
Reviewed-by: Piotr Haber <phaber@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: fix returning cipher_suite for get_key operation.
When multiple cipher suites have been programmed then the lowest
suite is to be retured. This fixes issue when AP mode is using
CCMP and TKIP WPA combination where rekeying will fail.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
on stop_ap the dongle was not properly shutdown. As a result it was
not possible to restart AP or STA after AP operation without
restarting the device. This patch will fix that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx and rx michael tkip keys are always swapped in case being
configured per mac. This is wrong for AP. The swap should only
be done for STA mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Bolle [Wed, 3 Apr 2013 11:24:45 +0000 (12:24 +0100)]
ARM: 7690/1: mm: fix CONFIG_LPAE typos
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Tue, 2 Apr 2013 21:11:46 +0000 (22:11 +0100)]
ARM: 7689/1: add unwind annotations to ftrace asm
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 28 Mar 2013 10:17:55 +0000 (11:17 +0100)]
ARM: 7685/1: delay: use private ticks_per_jiffy field for timer-based delay ops
Commit 70264367a243 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 26 Mar 2013 22:35:04 +0000 (23:35 +0100)]
ARM: 7684/1: errata: Workaround for Cortex-A15 erratum 798181 (TLBI/DSB operations)
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Herring [Mon, 25 Mar 2013 16:02:48 +0000 (17:02 +0100)]
ARM: 7682/1: cache-l2x0: fix masking of RTL revision numbering and set_debug init
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Yehuda Yitschak <yehuday@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 3 Apr 2013 15:33:26 +0000 (16:33 +0100)]
ARM: iWMMXt: always enable iWMMXt support with PJ4 CPUs
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Torstein Hegge [Tue, 26 Mar 2013 21:10:05 +0000 (22:10 +0100)]
ALSA: usb: Work around CM6631 sample rate change bug
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
1) Fix VSOCK layer handling of context ID changes, from Reilly Grant.
2) Now that we have a synchronize_net() in netdev_rx_handler_unregister(),
we can't let any call sites hold locks. Unfortunately bonding does,
so we have to drop the rwlock there a little bit earlier, fix from
Veaceslav Falico.
3) MAC address setting loop exits one iteration too early in mlx4
driver, from Yan Burman.
4) Restore ipv6 routes properly upon ifdown/ifup of loopback, from
Balakumaran Kannan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: Handle changes to the VMCI context ID.
net IPv6 : Fix broken IPv6 routing table after loopback down-up
cbq: incorrect processing of high limits
net/mlx4_en: Fix setting initial MAC address
bonding: get netdev_rx_handler_unregister out of locks
Merge tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A small collection of fixes. The most important ones are those from
Stephen and Lars-Peter both of which fix cache issues that have been
lurking for a while but not manifesting noticably enough for anyone to
report them."
* tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: async: Add missing return
regmap: don't corrupt work buffer in _regmap_raw_write()
regmap: cache Fix regcache-rbtree sync
regmap: Initialize `map->debugfs' before regcache
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull DRM fixes from Dave Airlie:
"Two core fixes, both regressions, along with some intel and some
nouveau fixes for regressions and oopses"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: correctly restore mappings if drm_open fails
drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
drm/nouveau: fix handling empty channel list in ioctl's
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c13 ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
PCI: Don't try to disable Bus Master on disconnected PCI devices
This is a fix for commit 7897e60227 ("PCI: Disable Bus Master
unconditionally in pci_device_shutdown()"). Vivek reported that
with this commit, kexec failed because none of his SATA disks
came up.
A ->shutdown() callback might put the device in D3cold, which means config
space is no longer available.
[bhelgaas: changelog] Link: https://lkml.org/lkml/2013/3/12/529 Reported-and-Tested-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit broke some pre-1.1 PCIe devices by leaving them with
ASPM enabled. Previously, we had disabled ASPM on these devices
because many of them don't implement it correctly (per 149e1637).
Requesting _OSC control early means that aspm_disabled may be set
before we scan the PCI bus and configure link ASPM state. But the
ASPM configuration currently skips the check for pre-PCIe 1.1 devices
when aspm_disabled is set, like this:
acpi_pci_root_add
acpi_pci_osc_support
if (flags != base_flags)
pcie_no_aspm
aspm_disabled = 1
pci_acpi_scan_root
...
pcie_aspm_init_link_state
pcie_aspm_sanity_check
if (!aspm_disabled)
/* check for pre-PCIe 1.1 device */
Therefore, setting aspm_disabled early means that we leave ASPM enabled
on these pre-PCIe 1.1 devices, which is a regression for some devices.
The best fix would be to clean up the ASPM init so we can evaluate
_OSC before scanning the bug (that way boot-time and hot-add discovery
will work the same), but that requires significant rework.
For now, we'll just revert the _OSC change as the lowest-risk fix.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=55211 Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Yinghai Lu <yinghai@kernel.org> CC: stable@vger.kernel.org # v3.8+
If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)
Dave Airlie [Tue, 2 Apr 2013 20:41:15 +0000 (06:41 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
One locking regression fix, and a couple of other i915 ones.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Reilly Grant [Mon, 1 Apr 2013 18:41:52 +0000 (11:41 -0700)]
VSOCK: Handle changes to the VMCI context ID.
The VMCI context ID of a virtual machine may change at any time. There
is a VMCI event which signals this but datagrams may be processed before
this is handled. It is therefore necessary to be flexible about the
destination context ID of any datagrams received. (It can be assumed to
be correct because it is provided by the hypervisor.) The context ID on
existing sockets should be updated to reflect how the hypervisor is
currently referring to the system.
Signed-off-by: Reilly Grant <grantr@vmware.com> Acked-by: Andy King <acking@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net IPv6 : Fix broken IPv6 routing table after loopback down-up
IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.
IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.
This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.
==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org> Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipc: set msg back to -EAGAIN if copy wasn't performed
Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found. This
garantees that msg is either a error pointer or a copy address.
Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yan Burman [Tue, 2 Apr 2013 13:49:45 +0000 (16:49 +0300)]
net/mlx4_en: Fix setting initial MAC address
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yan Burman <yanb@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: get netdev_rx_handler_unregister out of locks
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Merge tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx into fixes
From Anton Vorontsov <anton@enomsg.org>:
This tag includes Mac Lin's work to revive CNS3xxx booting:
"Since commit 0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), [...] the pre-defined iotable mappings is not in the vmalloc
region. [...] move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region."
Plus there is a small cosmetic fix, also from Mac Lin.
* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
ARM: cns3xxx: fix mapping of private memory region
[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Jussi Kivilinna [Thu, 28 Mar 2013 19:54:03 +0000 (21:54 +0200)]
crypto: gcm - fix assumption that assoc has one segment
rfc4543(gcm(*)) code for GMAC assumes that assoc scatterlist always contains
only one segment and only makes use of this first segment. However ipsec passes
assoc with three segments when using 'extended sequence number' thus in this
case rfc4543(gcm(*)) fails to function correctly. Patch fixes this issue.
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com> Tested-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com> Cc: stable@vger.kernel.org Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mengdong Lin [Thu, 28 Mar 2013 09:20:22 +0000 (05:20 -0400)]
ALSA: hda - bug fix on return value when getting HDMI ELD info
In function snd_hdmi_get_eld(), the variable 'ret' should be initialized to 0.
Otherwise it will be returned uninitialized as non-zero after ELD info is got
successfully. Thus hdmi_present_sense() will always assume ELD info is invalid
by mistake, and /proc file system cannot show the proper ELD info.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: stable@vger.kernel.org Acked-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"One reversion, a tiny leak fix, and a cc:stable locking fix, in two
parts"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio: console: add locking around c_ovq operations
virtio: console: rename cvq_lock to c_ivq_lock
hw_random: free rng_buffer at module exit
Revert "virtio_console: Initialize guest_connected=true for rproc_serial"
* pci/mjg-rom:
radeon: Attempt to use platform-provided ROM image
nouveau: Attempt to use platform-provided ROM image
PCI: Add PCI ROM helper for platform-provided ROM images
struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".
But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:
[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
time we call loop_set_fd() we check that loop_device->lo_state is
Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
it will get EBUSY. And if we try to loop_clr_fd() on unbound loop
device we'll get ENXIO.
loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
loop_device->lo_ctl_mutex. ]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull tegra clock driver fix from Mike Turquette:
"Missing base address in Tegra clock driver results in non-operational
PCIe. On some devices this means that Ethernet will go uninitialized
and other devices will fail. This pull request fixes it with a single
patch to pass the proper base address in the Tegra clock driver."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: tegra: Allow PLLE training to succeed
Merge tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe
Pull FCoE fixes from Robert Love:
"Critical patches to fix FCoE VN2VN mode with new interfaces targeting
3.9-rc"
* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
libfcoe: Fix fcoe_sysfs VN2VN mode
libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
fcoe: Fix deadlock between create and destroy paths
bnx2fc: Make the fcoe_cltr the SCSI host parent
Merge tag 'nfc-fixes-3.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the 2nd batch of NFC fixes for 3.9. This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thierry Reding [Thu, 14 Mar 2013 15:27:05 +0000 (16:27 +0100)]
clk: tegra: Allow PLLE training to succeed
Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
so eisa_probe will fail from pci_eisa_init
==>eisa_root_register
==>eisa_probe path.
as force_probe is not set in pci_eisa_root, it will bail early when
slot0 is not probed and initialized.
Try to use subsys_initcall_sync instead, and will keep following sequence:
pci_subsys_init
pci_eisa_init_early
pnpacpi_init/isapnp_init
After this patch EISA can be initialized properly, and PNP overlapping
resource will not be reserved.
[ 10.104434] system 00:0f: [io 0x0c80-0x0c84] could not be reserved
Reported-by: Matthew Whitehead <mwhitehe@redhat.com> Tested-by: Matthew Whitehead <mwhitehe@redhat.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org
Yinghai Lu [Mon, 1 Apr 2013 17:48:59 +0000 (11:48 -0600)]
EISA/PCI: Fix bus res reference
Matthew found that 3.8.3 is having problems with an old (ancient)
PCI-to-EISA bridge, the Intel 82375. It worked with the 3.2 kernel.
He identified the 82375, but doesn't assign the struct resource *res
pointer inside the struct eisa_root_device, and panics.
pci_eisa_init() was using bus->resource[] directly instead of
pci_bus_resource_n(). The bus->resource[] array is a PCI-internal
implementation detail, and after commit 45ca9e97 (PCI: add helpers for
building PCI bus resource lists) and commit 0efd5aab (PCI: add struct
pci_host_bridge_window with CPU/bus address offset), bus->resource[] is not
used for PCI root buses any more.
The 82375 is a subtractive-decode PCI device, so handle it the same
way we handle PCI-PCI bridges in subtractive-decode mode in
pci_read_bridge_bases().
[bhelgaas: changelog] Reported-by: Matthew Whitehead <mwhitehe@redhat.com> Tested-by: Matthew Whitehead <mwhitehe@redhat.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org # v3.3+
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fix from Chris Metcalf:
"This change allows newer Tilera boot tools to work correctly with
current (and stable) kernels by using the right filename to get the
initramfs from the Tilera hypervisor filesystem."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: expect new initramfs name from hypervisor file system
1) sadb_msg prepared for IPSEC userspace forgets to initialize the
satype field, fix from Nicolas Dichtel.
2) Fix mac80211 synchronization during station removal, from Johannes
Berg.
3) Fix IPSEC sequence number notifications when they wrap, from Steffen
Klassert.
4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
error pointer, from Johannes Berg.
5) In mac80211, don't call into the channel context code with the
interface list mutex held. From Johannes Berg.
6) In mac80211, if we don't actually associate, do not restart the STA
timer, otherwise we can crash. From Ben Greear.
7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e. From
Christoph Paasch.
8) Fix sja1000 driver defines to not conflict with SH port, from Marc
Kleine-Budde.
9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
King.
10) Suspend/Resume in the FEC driver fail because the buffer descriptors
are not initialized at all the moments in which they should. Fix
from Frank Li.
11) cpsw and davinci_emac drivers both use the wrong interface to
restart a stopped TX queue. Use netif_wake_queue not
netif_start_queue, the latter is for initialization/bringup not
active management of the queue. From Mugunthan V N.
12) Fix regression in rate calculations done by
psched_ratecfg_precompute(), missing u64 type promotion. From
Sergey Popovich.
13) Fix length overflow in tg3 VPD parsing, from Kees Cook.
14) AOE driver fails to allocate enough headroom, resulting in crashes.
Fix from Eric Dumazet.
15) RX overflow happens too quickly in sky2 driver because pause packet
thresholds are not programmed correctly. From Mirko Lindner.
16) Bonding driver manages arp_interval and miimon settings incorrectly,
disabling one unintentionally disables both. Fix from Nikolay
Aleksandrov.
17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
Fix from Steve Glendinning.
18) Fix off-by-one in Codel packet scheduler. From Vijay Subramanian.
19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
Frederic Sowa.
20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
crashes in bonding driver unload stress tests. From Eric Dumazet.
21) rxlen field of ks8851 RX packet descriptors not interpreted
correctly (it is 12 bits not 16 bits, so needs to be masked after
shifting the 32-bit value down 16 bits). Fix from Max Nekludov.
22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
change indications. From Sergei Shtylyov.
23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
from Sergei Shtylyov.
24) dm9000 driver initialization is done wrong for revision B devices
with DSP PHY, from Joseph CHANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
DM9000B: driver initialization upgrade
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
sh_eth: workaround for spurious ECI interrupt
sh_eth: fix handling of no LINK signal
ks8851: Fix interpretation of rxlen field.
net: add a synchronize_net() in netdev_rx_handler_unregister()
MAINTAINERS: Update netxen_nic maintainers list
atl1e: drop pci-msi support because of packet corruption
net: fq_codel: Fix off-by-one error
net: calxedaxgmac: Wake-on-LAN fixes
net: calxedaxgmac: fix rx ring handling when OOM
net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
smsc75xx: fix jumbo frame support
net: fix the use of this_cpu_ptr
bonding: fix disabling of arp_interval and miimon
ipv6: don't accept node local multicast traffic from the wire
sky2: Threshold for Pause Packet is set wrong
sky2: Receive Overflows not counted
aoe: reserve enough headroom on skbs
line up comment for ndo_bridge_getlink
...
Joseph CHANG [Thu, 28 Mar 2013 23:13:42 +0000 (23:13 +0000)]
DM9000B: driver initialization upgrade
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 10:11:04 +0000 (10:11 +0000)]
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 09:54:20 +0000 (09:54 +0000)]
sh_eth: workaround for spurious ECI interrupt
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Max Filippov <max.filippov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 09:50:07 +0000 (09:50 +0000)]
sh_eth: fix handling of no LINK signal
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sam Ravnborg [Sat, 30 Mar 2013 11:44:24 +0000 (11:44 +0000)]
bbc_i2c: fix section mismatch warning
Fix following warning:
WARNING: drivers/sbus/char/bbc.o(.text+0x674): Section mismatch in reference from the function bbc_i2c_probe() to the function .init.text:T.463()
The function bbc_i2c_probe() references the function __init T.463().
This is often because bbc_i2c_probe lacks a __init
annotation or the annotation of T.463 is wrong.
bbc_i2c_probe() referenced the inlined attach_one_i2c().
As probe may be called after init drop __init annotations
on all functions used by bbc_i2c_probe()
The warning was seen with a sparc64 defconfig build
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kefeng Wang [Sat, 30 Mar 2013 00:28:26 +0000 (00:28 +0000)]
sparc:cleanup unused code in smp_32.h
After genirq and generic clockevent support at sparc32,
smp4m_irq_rotate(), prof_multiplier() and prof_counter()
are no longer used and should be removed.
Akinobu Mita [Fri, 29 Mar 2013 03:44:44 +0000 (03:44 +0000)]
sparc/iommu: fix typo s/265KB/256KB/
IOMMU_NPTES is 64K PTEs, so the size is 256KB (= 64K * sizeof(iopte_t))
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Fri, 29 Mar 2013 03:44:43 +0000 (03:44 +0000)]
sparc/srmmu: clear trailing edge of bitmap properly
srmmu_nocache_bitmap is cleared by bit_map_init(). But bit_map_init()
attempts to clear by memset(), so it can't clear the trailing edge of
bitmap properly on big-endian architecture if the number of bits is not
a multiple of BITS_PER_LONG.
Actually, the number of bits in srmmu_nocache_bitmap is not always
a multiple of BITS_PER_LONG. It is calculated as below:
srmmu_nocache_size is decided proportionally by the amount of system RAM
and it is rounded to a multiple of PAGE_SIZE. SRMMU_NOCACHE_BITMAP_SHIFT
is defined as (PAGE_SHIFT - 4). So it can only be said that bitmap_bits
is a multiple of 16.
This fixes the problem by using bitmap_clear() instead of memset()
in bit_map_init() and this also uses BITS_TO_LONGS() to calculate correct
size at bitmap allocation time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 31 Mar 2013 18:41:47 +0000 (11:41 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Two fixes for slave-dmaengine.
The first one is for making slave_id value correct for dw_dmac and
the other one fixes the endieness in DT parsing"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
Linus Torvalds [Sun, 31 Mar 2013 18:40:33 +0000 (11:40 -0700)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a some fixes for Kernel 3.9:
- subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
- compilation fix for arm multiarch preventing IR_RX51 to be selected
- regression fix at bttv crop logic
- s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] [REGRESSION] bt8xx: Fix too large height in cropcap
[media] fix compilation with both V4L2 and I2C as 'm'
[media] m5mols: Fix bug in stream on handler
[media] s5p-fimc: Do not attempt to disable not enabled media pipeline
[media] s5p-mfc: Fix encoder control 15 issue
[media] s5p-mfc: Fix frame skip bug
[media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
[media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
[media] fimc-lite: Fix the variable type to avoid possible crash
[media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
[media] ir: IR_RX51 only works on OMAP2
Linus Torvalds [Sun, 31 Mar 2013 18:38:59 +0000 (11:38 -0700)]
Merge tag 'for-linus-20130331' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Alright, this time from 10K up in the air.
Collection of fixes that have been queued up since the merge window
opened, hence postponed until later in the cycle. The pull request
contains:
- A bunch of fixes for the xen blk front/back driver.
- A round of fixes for the new IBM RamSan driver, fixing various
nasty issues.
- Fixes for multiple drives from Wei Yongjun, bad handling of return
values and wrong pointer math.
- A fix for loop properly killing partitions when being detached."
* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
mg_disk: fix error return code in mg_probe()
rsxx: remove unused variable
rsxx: enable error return of rsxx_eeh_save_issued_dmas()
block: removes dynamic allocation on stack
Block: blk-flush: Fixed indent code style
cciss: fix invalid use of sizeof in cciss_find_cfgtables()
loop: cleanup partitions when detaching loop device
loop: fix error return code in loop_add()
mtip32xx: fix error return code in mtip_pci_probe()
xen-blkfront: remove frame list from blk_shadow
xen-blkfront: pre-allocate pages for requests
xen-blkback: don't store dev_bus_addr
xen-blkfront: switch from llist to list
xen-blkback: fix foreach_grant_safe to handle empty lists
xen-blkfront: replace kmalloc and then memcpy with kmemdup
xen-blkback: fix dispatch_rw_block_io() error path
rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
Adding in EEH support to the IBM FlashSystem 70/80 device driver
block: IBM RamSan 70/80 error message bug fix.
block: IBM RamSan 70/80 branding changes.
...
Commit 6aa9707099c4 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems. The failures were noticed on
OMAP2 and 3 boards during kernel init:
[ BUG: swapper/0/1 still has locks held! ] 3.9.0-rc3-00344-ga937536 #1 Not tainted
-------------------------------------
1 lock held by swapper/0/1:
#0: (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574
cfg80211_conn_scan() which requires sched_scan_mtx to be held can be called
from cfg80211_conn_work(). Without this we are hitting multiple warnings like
the following:
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the bug-fix for a >= v3.8-rc1 regression specific to
iscsi-target persistent reservation conflict handling (CC'ed to
stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
so that in-flight qemu vhost-scsi-pci device code can detect the
proper vhost feature bits.
Also, there are two more tcm_vhost patches still being discussed by
MST and Asias for v3.9 that will be required for the in-flight qemu
vhost-scsi-pci device patch to function properly, and that should
(hopefully) be the last target fixes for this round."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Mac Lin [Mon, 25 Mar 2013 09:23:33 +0000 (17:23 +0800)]
ARM: cns3xxx: fix mapping of private memory region
Since commit 0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.
This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.
Signed-off-by: Mac Lin <mkl0301@gmail.com> Signed-off-by: Anton Vorontsov <anton@enomsg.org> Cc: stable@vger.kernel.org [v3.3+]
Amit Shah [Fri, 29 Mar 2013 11:00:08 +0000 (16:30 +0530)]
virtio: console: add locking around c_ovq operations
When multiple ovq operations are being performed (lots of open/close
operations on virtio_console fds), the __send_control_msg() function can
get confused without locking.
A simple recipe to cause badness is:
* create a QEMU VM with two virtio-serial ports
* in the guest, do
while true;do echo abc >/dev/vport0p1;done
while true;do echo edf >/dev/vport0p2;done
In one run, this caused a panic in __send_control_msg(). In another, I
got
virtio_console virtio0: control-o:id 0 is not a head!
This also results repeated messages similar to these on the host:
qemu-kvm: virtio-serial-bus: Unexpected port id 478762112 for device virtio-serial-bus.0
qemu-kvm: virtio-serial-bus: Unexpected port id 478762368 for device virtio-serial-bus.0
Reported-by: FuXiangChun <xfu@redhat.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Reviewed-by: Asias He <asias@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org
Amit Shah [Fri, 29 Mar 2013 11:00:07 +0000 (16:30 +0530)]
virtio: console: rename cvq_lock to c_ivq_lock
The cvq_lock was taken for the c_ivq. Rename the lock to make that
obvious.
We'll also add a lock around the c_ovq in the next commit, so there's no
ambiguity.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Reviewed-by: Asias He <asias@redhat.com> Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org
Andy Shevchenko [Wed, 20 Feb 2013 11:52:17 +0000 (13:52 +0200)]
dw_dmac: adjust slave_id accordingly to request line base
On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Arnd Bergmann [Sun, 3 Mar 2013 20:51:28 +0000 (20:51 +0000)]
dmaengine: dw_dma: fix endianess for DT xlate function
As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Fri, 29 Mar 2013 03:01:22 +0000 (03:01 +0000)]
net: add a synchronize_net() in netdev_rx_handler_unregister()
commit 35d48903e97819 (bonding: fix rx_handler locking) added a race
in bonding driver, reported by Steven Rostedt who did a very good
diagnosis :
<quoting Steven>
I'm currently debugging a crash in an old 3.0-rt kernel that one of our
customers is seeing. The bug happens with a stress test that loads and
unloads the bonding module in a loop (I don't know all the details as
I'm not the one that is directly interacting with the customer). But the
bug looks to be something that may still be present and possibly present
in mainline too. It will just be much harder to trigger it in mainline.
In -rt, interrupts are threads, and can schedule in and out just like
any other thread. Note, mainline now supports interrupt threads so this
may be easily reproducible in mainline as well. I don't have the ability
to tell the customer to try mainline or other kernels, so my hands are
somewhat tied to what I can do.
But according to a core dump, I tracked down that the eth irq thread
crashed in bond_handle_frame() here:
slave = bond_slave_get_rcu(skb->dev);
bond = slave->bond; <--- BUG
the slave returned was NULL and accessing slave->bond caused a NULL
pointer dereference.
Which is basically:
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
And looking at __netif_receive_skb() we have:
rx_handler = rcu_dereference(skb->dev->rx_handler);
if (rx_handler) {
if (pt_prev) {
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = NULL;
}
switch (rx_handler(&skb)) {
My question to all of you is, what stops this interrupt from happening
while the bonding module is unloading? What happens if the interrupt
triggers and we have this:
What protection am I missing in the bond release handler that would
prevent the above from happening?
</quoting Steven>
We can fix bug this in two ways. First is adding a test in
bond_handle_frame() and others to check if rx_handler_data is NULL.
A second way is adding a synchronize_net() in
netdev_rx_handler_unregister() to make sure that a rcu protected reader
has the guarantee to see a non NULL rx_handler_data.
The second way is better as it avoids an extra test in fast path.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: Paul E. McKenney <paulmck@us.ibm.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1e: drop pci-msi support because of packet corruption
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com> Cc: Huang, Xiong <xiong@qca.qualcomm.com> Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we hold a max of sch->limit -1 number of packets instead of
sch->limit packets. Fix this off-by-one error.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log