Eddi De Pieri [Sat, 19 Nov 2011 14:37:14 +0000 (11:37 -0300)]
[media] em28xx: initial support for HAUPPAUGE HVR-930C again
With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues] Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Eddi De Pieri <eddi@depieri.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] Properly implement ITU-T J.88 Annex C support
The Annex C support were broken with the previous implementation,
as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth
for some symbol rates.
At DRX-J, it were always selecting Annex A, even having Annex C
support coded there.
[media] dvb: Allow select between DVB-C Annex A and Annex C
DVB-C, as defined by ITU-T J.83 has 3 annexes. The differences between
Annex A and Annex C is that Annex C uses a subset of the modulation
types, and uses a different rolloff factor. A different rolloff means
that the bandwidth required is slicely different, and may affect the
saw filter configuration at the tuners. Also, some demods have different
configurations, depending on using Annex A or Annex C.
So, allow userspace to specify it, by changing the rolloff factor.
Jean Delvare [Mon, 7 Nov 2011 08:24:49 +0000 (05:24 -0300)]
[media] usbvision: Drop broken 10-bit I2C address support
The support for 10-bit I2C addresses in usbvision seems plain broken
to me. I had already noticed that back in February 2007 [1]. The code
was not fixed since then, so I take it that it's not actually needed.
And as a matter of fact I don't know of any 10-bit addressed I2C
tuner, encode, decoder or the like.
So let's simply get rid of the broken and useless code.
I'm also adding I2C_FUNC_I2C, as the driver and hardware support plain
I2C messaging.
[media] staging: as102: Eliminate as10x_handle_t alias
Remove pre-processor defined as10x_handle_t data type by directly
replacing it with struct as102_bus_adapter_t. phandle is renamed
to adap inside function bodies.
[media] staging: as102: Fix the dvb device registration error path
Release already acquired resources when error happens during
devices registration steps.
Use dev_err() where struct device is available, instead of driver
specific err().
[media] staging: as102: Make the driver select CONFIG_FW_LOADER
It doesn't seem to be of much advantage to compile in FW_LOADER
support conditionally, then make the driver always select FW_LOADER
and remove #idefs from the code.
[media] staging: as102: Remove leftovers of the SPI bus driver
SPI bus driver support is not included in this module, the SPI
driver files are missing. But some bits are still present so
clean up the unused code.
The SPI driver support can be properly added later if needed.
Then CONFIG_AS102_SPI and CONFIG_AS102_USB is now not needed
and the pre-processor statements using these config options
can now be removed from *.c files.
[media] bt8xx: add support for Tongwei Video Technology TD-3116
The following patch adds support for the Tongwei Video Technology TD-3116 board. This
is a Bt878 based capture card with 16 inputs meant for surveilance applications.
It also offers a way to check which inputs have a video signal while capturing another
input. In addition there are a number of alarm inputs and outputs available and there
is microcontroller which is presumably intended for use as a system watchdog. None of
these extra capabilities are supported by the patch.
Signed-off-by: Peter De Schrijver <p2@psychaos.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kamil Debski [Thu, 6 Oct 2011 14:32:12 +0000 (11:32 -0300)]
[media] v4l: add G2D driver for s5p device family
G2D is a 2D graphics accelerator engine present in the s5p family
of Samsung SoCs. It is capable of bitblt and raster operations on
images having dimensions of up to 8000x8000.
Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Josh Boyer [Wed, 2 Nov 2011 19:39:58 +0000 (16:39 -0300)]
[media] ttusb2: Don't use stack variables for DMA
The ttusb2_msg function uses on-stack variables to submit commands to
dvb_usb_generic. This eventually gets to the DMA api layer and will throw a
traceback if the debugging options are set.
This allocates the temporary buffer variables with kzalloc instead.
Support for version 2 type chips and other LNA versions of version 1
Scripts may be compressed slightly at a later stage.
TODO
Firmware loader
However, things are a little confusing, it is not clear that
dvb-usb-it9137-01.fw does not work with version 2 chips
as in recent files both firmwares are the same.
Should be applied to: 8133 Support for single ITE 9135 device.
Michael Krufky [Mon, 31 Oct 2011 11:12:54 +0000 (08:12 -0300)]
[media] s5h1411: Calculate signal strength shown as percentage from SNR up to 35dB
As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 31 Oct 2011 11:12:18 +0000 (08:12 -0300)]
[media] s5h1409: Calculate signal strength shown as percentage from SNR up to 35dB
As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 31 Oct 2011 11:11:00 +0000 (08:11 -0300)]
[media] au8522: Calculate signal strength shown as percentage from SNR up to 35dB
As done first in lgdt330x.c, calculate signal strength from SNR up to 35dB
Even though the SNR can go higher than 35dB, there is some comfort factor
in having a range of strong signals that can show at 100%
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Julia Lawall [Fri, 28 Oct 2011 22:58:17 +0000 (19:58 -0300)]
[media] drivers/media/video/davinci/vpbe_display.c: eliminate a null pointer dereference
In the original code, probe_out could be reached when res was null and then
when the irq had not yet been requested. In those cases, the call to
free_irq is not needed, so move probe_out down and introduce a new label
for the case where calling free_irq is useful.
The semantic match that finds this problem is as follows:
[media] Make use of media bus pixel codes in adv7170 driver
The ADV7170/ADV7171 can operate in either 8-bit or 16-bit YCrCb Mode.
* 8-Bit YCrCb Mode
This default mode accepts multiplexed YCrCb inputs through
the P7-P0 pixel inputs. The inputs follow the sequence Cb0, Y0
Cr0, Y1 Cb1, Y2, etc. The Y, Cb and Cr data are input on a
rising clock edge.
* 16-Bit YCrCb Mode
This mode accepts Y inputs through the P7–P0 pixel inputs and
multiplexed CrCb inputs through the P15–P8 pixel inputs. The
data is loaded on every second rising edge of CLOCK. The inputs
follow the sequence Cb0, Y0 Cr0, Y1 Cb1, Y2, etc.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Daniel Drake [Wed, 26 Oct 2011 12:16:50 +0000 (09:16 -0300)]
[media] via-camera: disable RGB mode
The RGB mode does not work correctly. It captures fine at 640x480
but whenever the scaling engine is used to produce another resolution,
color corruption occurs (lots of erroneous pink and green).
It is not clear how the scaling engine is supposed to work and how
it knows which pixel format it is dealing with. Work around this
problem by disabling RGB support. YUYV scaling works just fine.
Laurent Pinchart [Sat, 22 Oct 2011 07:57:54 +0000 (04:57 -0300)]
[media] v4l: mt9p031/mt9t001: Use i2c_smbus_{read|write}_word_swapped()
The MT9P031 and MT9T001 sensors transfer 16-bit data on the I2C bus in
swapped order. Let the I2C core handle byte order by using the
i2c_smbus_{read|write}_word_swapped() functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] OMAP_VOUT: Increase MAX_DISPLAYS to a larger value
There is no limit to the number of displays that can registered with DSS2. The
current value of MAX_DISPLAYS is 3, set this to 10 so that the 'displays'
member of omap2video_device struct can store more omap_dss_device pointers.
This fixes a crash seen in omap_vout_probe when DSS2 registers for more than 3
displays.
Add support for DSI panels. DSI video mode panels will work directly. For
command mode panels, we will need to trigger updates regularly. This isn't done
by the omap_vout driver currently. It can still be supported if we connect a
framebuffer device to the panel and configure it in auto update mode.
[media] OMAP_VOUT: Fix VSYNC IRQ handling in omap_vout_isr
Currently, in omap_vout_isr(), if the panel type is DPI, and if we
get either VSYNC or VSYNC2 interrupts, we proceed ahead to set the
current buffers state to VIDEOBUF_DONE and prepare to display the
next frame in the queue.
On OMAP4, because we have 2 LCD managers, the panel type itself is not
sufficient to tell if we have received the correct irq, i.e, we shouldn't
proceed ahead if we get a VSYNC interrupt for LCD2 manager, or a VSYNC2
interrupt for LCD manager.
Fix this by correlating LCD manager to VSYNC interrupt and LCD2 manager
to VSYNC2 interrupt.
[media] OMAP_VOUT: CLEANUP: Remove redundant code from omap_vout_isr
Currently, there is a lot of redundant code is between DPI and VENC panels, this
can be made common by moving out field/interlace specific code to a separate
function called omapvid_handle_interlace_display(). There is no functional
change made.
[media] OMAP_VOUT: Fix check in reqbuf for buf_size allocation
The commit 383e4f69879d11c86ebdd38b3356f6d0690fb4cc makes reqbuf prevent
requesting a larger size buffer than what is allocated at kernel boot during
omap_vout_probe.
In omap_vout_buffer_setup callback API, the requested size is compared with
vout->buffer_size, this isn't correct as vout->buffer_size is later set to the
size requested in reqbuf. When the video device is opened the next time, this
check will prevent us to allocate a buffer which is larger than what we requested
the last time.
Don't use vout->buffer_size, always check with the parameters video1_bufsize
or video2_bufsize.
Antti Palosaari [Tue, 6 Sep 2011 01:10:05 +0000 (22:10 -0300)]
[media] anysee: I2C gate control DNOD44CDH086A tuner module
DNOD44CDH086A (NXP TDA18212) tuner module is not connected to
demodulator I2C gate. Instead demodulator gate it uses external
GPIO driven gate. Override demodulator I2C gate control with
own in that case.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Thu, 13 Oct 2011 05:41:41 +0000 (02:41 -0300)]
[media] cx25821: off by one in cx25821_vidioc_s_input()
If "i" is 2 then when we call cx25821_video_mux() we'd end up going
past the end of the cx25821_boards[dev->board]->input[].
The INPUT() macro obfuscates what's going on in that function so it's
a bit hard to follow. And as Mauro points out the hard coded 2 is
not very helpful.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Paul Bolle [Wed, 12 Oct 2011 20:51:22 +0000 (17:51 -0300)]
[media] media: tea5764: reconcile Kconfig symbol and macro
The Kconfig symbol RADIO_TEA5764_XTAL is unused. The code does use a
RADIO_TEA5764_XTAL macro, but does that rather peculiar. But there seems
to be a way to keep both. (The easiest way out would be to rip out both
the Kconfig symbol and the macro.)
Note there's also a module parameter 'use_xtal' to influence all this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] omap3isp: preview: Add crop support on the sink pad
The crop rectangle takes the preview engine internal cropping
requirements into account. The smallest allowable margins are 14 columns
and 8 rows when reading from memory, and 18 columns and 8 rows when
processing data on the fly from the CCDC.
The macros that define the minimum/maximum input and output sizes are
defined in seperate files and have no consistent naming. In preparation
for preview engine cropping support, move them all to isppreview.c and
rename them to PREV_{MIN|MAX}_{IN|OUT}_{WIDTH|HEIGHT}*.
Remove unused and/or unneeded local variables that store the maximum
output width.
[media] omap3isp: preview: Remove horizontal averager support
The horizontal averager isn't used and will get in the way when
implementing cropping support on the input pad. Remove it, it can be
added back later if needed.
[media] v4l: Add v4l2 subdev driver for S5K6AAFX sensor
This driver exposes preview mode operation of the S5K6AAFX sensor with
embedded SoC ISP. The native capture (snapshot) operation mode is not
supported.
Following controls are available:
manual/auto exposure and gain, power line frequency (anti-flicker),
saturation, sharpness, brightness, contrast, white balance temperature,
color effects, horizontal/vertical image flip, frame interval,
auto white balance.
RGB component gains are currently exposed through private controls.
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] v4l: Add AUTO option for the V4L2_CID_POWER_LINE_FREQUENCY control
V4L2_CID_POWER_LINE_FREQUENCY control allows applications to instruct
a driver what is the power line frequency so an appropriate filter
can be used by the device to cancel flicker by compensating the light
intensity ripple. Currently in the menu we have entries for 50 Hz and
60 Hz and for entirely disabling the anti-flicker filter.
However some devices are capable of automatically detecting the
frequency, so add V4L2_CID_POWER_LINE_FREQUENCY_AUTO entry for them.
* with no "retrun ret;" at the end, there is no need to initialize ret
any longer,
* consequently use conditional expressions, not if...else constructs,
throughout ov6650_s_ctrl(),
* v4l2_ctrl_new_std_menu() max value of V4L2_EXPOSURE_MANUAL instead of
equivalent 1 looks more clear.
Created on top of "Converting soc_camera to the control framework"
series.
[media] V4L: replace soc-camera specific soc_mediabus.h with v4l2-mediabus.h
Most users of the <media/soc_mediabus.h> header only need pixel code
definitions, which are now located in the generic <linux/v4l2-mediabus.h>
header. Switch over to reduce soc-camera dependencies.
[media] V4L: soc-camera: make (almost) all client drivers re-usable outside of the framework
The most important change in this patch is direct linking to struct
soc_camera_link via the client->dev.platform_data pointer. This makes most
of the soc-camera client drivers also usable outside of the soc-camera
framework. After this change all what is needed for these drivers to
function are inclusions of soc-camera headers for some convenience macros,
suitably configured platform data, which is anyway always required, and
loaded soc-camera core module for library functions. If desired, these
library functions can be made generic in the future and moved to a more
neutral location.
The only two client drivers, that still depend on soc-camera are:
mt9t031: it uses struct video_device for its PM. Since no hardware is
available, alternative methods cannot be tested.
ov6650: it uses struct soc_camera_device to pass its sense data back to
the bridge driver. A generic v4l2-subdevice approach should be developed
to perform this.
VIDIOC_G_STD can return the current TV-norm to the user in one of two ways:
if an .vidioc_g_std() ioctl operation is provided by the driver, it is
called, otherwise the value ot the .current_norm field of struct
video_device is returned. Since subdevice drivers currently have no access
to struct video_device objects, the only way to provide this information to
the user is by implementing a .g_std() method.
[media] V4L: dynamically allocate video_device nodes in subdevices
Currently only very few drivers actually use video_device nodes, embedded
in struct v4l2_subdev. Allocate these nodes dynamically for those drivers
to save memory for the rest.
If the sh_mobile_csi2 driver didn't attach to a client, normally, because
the respective device connects to the SoC over the parallel CEU interface
and doesn't use the CSI-2 controller, it also shouldn't call
pm_runtime_put() on attempted disconnect.
[media] V4L: mt9m001, mt9v022: use internally cached pixel code
Using the internally cached pixel code, instead of the one, provided by
the soc-camera, removes one more use of struct soc_camera_device in these
drivers. Also remove the no longer needed soc_camera_from_i2c() inline
function.
[media] V4L: soc-camera: start removing struct soc_camera_device from client drivers
Remove most trivial uses of struct soc_camera_device from most client
drivers, abstracting some of them inside inline functions. Next steps
will eliminate remaining uses and modify inline functions to not use
struct soc_camera_device.
projects / mv-sheeva.git / log