Linus Torvalds [Sun, 6 Dec 2015 00:06:30 +0000 (16:06 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
Linus Torvalds [Sat, 5 Dec 2015 18:46:44 +0000 (10:46 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
Dave Airlie [Sat, 5 Dec 2015 06:15:38 +0000 (16:15 +1000)]
Merge branch 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux into drm-next
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
Alex Deucher [Thu, 3 Dec 2015 17:31:56 +0000 (12:31 -0500)]
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Linus Torvalds [Fri, 4 Dec 2015 19:30:45 +0000 (11:30 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- NFIT parsing regression fixes from Linda. The nvdimm hot-add
implementation merged in 4.4-rc1 interpreted the specification in a
way that breaks actual HPE platforms. We are also closing the loop
with the ACPI Working Group to get this clarification added to the
spec.
- Andy pointed out that his laptop without nvdimm resources is loading
the e820-nvdimm module by default, fix that up to only load the
module when an e820-type-12 range is present.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Adjust for different _FIT and NFIT headers
nfit: Fix the check for a successful NFIT merge
nfit: Account for table size length variation
libnvdimm, e820: skip module loading when no type-12
Linus Torvalds [Fri, 4 Dec 2015 18:17:20 +0000 (10:17 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull ARM KVM fixes from Paolo Bonzini:
- a series of fixes to deal with the aliasing between the sp and xzr
register
- a fix for the cache flush fix that went in -rc3
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM/arm64: KVM: correct PTE uncachedness check
arm64: KVM: Get rid of old vcpu_reg()
arm64: KVM: Correctly handle zero register in system register accesses
arm64: KVM: Remove const from struct sys_reg_params
arm64: KVM: Correctly handle zero register during MMIO
Mario Kleiner [Wed, 25 Nov 2015 19:14:31 +0000 (20:14 +0100)]
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147 Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Michel Dänzer <michel.daenzer@amd.com> Cc: Harry Wentland <Harry.Wentland@amd.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude [Thu, 3 Dec 2015 23:26:07 +0000 (18:26 -0500)]
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The gtt_end is already inclusive, we don't need to subtract one here.
v2 (chk): keep the fix for the VM code, cause here it really applies.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:52 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference for the user fence
No need for a GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:51 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference in the display code
No need for the GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Fri, 4 Dec 2015 17:16:26 +0000 (09:16 -0800)]
Merge tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we've got a larger number of updates, mainly from ASoC
world. The only significant LOCs found here are for Realtek codecs,
where most of changes are quite systematic replacements.
There are also a few fixes in ASoC core side: one is the PM call order
fix to ensure the DPAM resume working properly. Another is the proper
cleanup call after freeing DAPM widgets, and the correction of the
wrong callback set in topology API.
The rest are a wide range of driver-specific small fixes, including
HD-audio"
* tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda - Add Conexant CX8200 (14f1:2008) codec entry
ALSA: hda - Correct codec names for 14f1:50f1 and 14f1:50f3
ALSA: hda - Skip ELD notification during system suspend
ASoC: core: Change power state before rechecking endpoint
ASoC: fix kernel-doc warnings in sound/soc/soc-ops.c
ASoC: rt5645: Add dmi_system_id "Google Terra"
ASoC: rockchip: Fix incorrect VDW value for 24 bit
ASoC: fsl: clarify ac97 dependency
ASoC: Intel: Skylake: fix memory leak
ASoC: davinci-mcasp: Fix master capture only mode
ASoC: es8328: Fix shifts for mixer switches
ASoC: rt5645: Add dmi_system_id "Google Wizpig"
ASoC: sti: set player private data
ASoC: sti: rename ST proprietary DT properties
ASoC: sti: remove wrong error message
ASoC: Intel: Skylake: Add I2C depends for SKL machine
ASoC: topology: fix info callback for TLV byte control
ASoC: rt5670: fix wrong bit def for pll src
ASoC: nau8825: add pm function
ASoC: rt5645: Add struct dmi_system_id "Google Edgar" for Chrome OS
...
Linus Torvalds [Fri, 4 Dec 2015 16:59:10 +0000 (08:59 -0800)]
Merge tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI PCI host bridge
initialization code, clean up some recent changes (generic power
domains framework, ACPI AML debugger support), fix three older but
annoying bugs (PCI power management. generic power domains framework,
cpufreq) and a build problem (device properties framework), and update
a stale MAINTAINERS entry (ACPI backlight driver).
Specifics:
- Fix a regression in the ACPI PCI host bridge initialization code
introduced by the recent consolidation of the host bridge handling
on x86 and ia64 that forgot to take one special piece of code
related to NUMA on x86 into account (Liu Jiang).
- Improve the Kconfig help description of the new ACPI AML debugger
support option to avoid possible confusion (Peter Zijlstra).
- Remove a piece of code in the generic power domains framework that
should have been removed by one of the recent commits modifying
that code (Ulf Hansson).
- Reduce the log level of a PCI PM message that generates a lot of
false-positive log noise for some drivers and improve the message
itself while at it (Imre Deak).
- Fix the OF-based domain lookup code in the generic power domains
framework to make it drop references to DT nodes correctly (Eric
Anholt).
- Prevent the cpufreq core from setting the policy back to the
default after a CPU offline/online cycle for cpufreq drivers
providing the ->setpolicy callback (Srinivas Pandruvada).
- Fix a build problem for CONFIG_ACPI unset in the device properties
framework (Hanjun Guo).
- Fix a stale file path in the ACPI backlight driver entry in
MAINTAINERS (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
cpufreq: use last policy after online for drivers with ->setpolicy
PCI / PM: Tune down retryable runtime suspend error messages
PM / Domains: Validate cases of a non-bound driver in genpd governor
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
x86/PCI/ACPI: Fix regression caused by commit 4d6b4e69a245
ACPI: Better describe ACPI_DEBUGGER
Ard Biesheuvel [Thu, 3 Dec 2015 08:25:22 +0000 (09:25 +0100)]
ARM/arm64: KVM: correct PTE uncachedness check
Commit e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's
uncachedness") modified the logic to test whether a HYP or stage-2
mapping needs flushing, from [incorrectly] interpreting the page table
attributes to [incorrectly] checking whether the PFN that backs the
mapping is covered by host system RAM. The PFN number is part of the
output of the translation, not the input, so we have to use pte_pfn()
on the contents of the PTE, not __phys_to_pfn() on the HYP virtual
address or stage-2 intermediate physical address.
Fixes: e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's uncachedness") Cc: stable@vger.kernel.org Tested-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:14 +0000 (15:03 +0300)]
arm64: KVM: Get rid of old vcpu_reg()
Using oldstyle vcpu_reg() accessor is proven to be inappropriate and
unsafe on ARM64. This patch converts the rest of use cases to new
accessors and completely removes vcpu_reg() on ARM64.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:13 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register in system register accesses
System register accesses also use zero register for Rt == 31, and
therefore using it will also result in getting SP value instead. This
patch makes them also using new accessors, introduced by the previous
patch. Since register value is no longer directly associated with storage
inside vCPU context structure, we introduce a dedicated storage for it in
struct sys_reg_params.
This refactor also gets rid of "massive hack" in kvm_handle_cp_64().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:12 +0000 (15:03 +0300)]
arm64: KVM: Remove const from struct sys_reg_params
Further rework is going to introduce a dedicated storage for transfer
register value in struct sys_reg_params. Before doing this we have to
remove 'const' modifiers from it in all accessor functions and their
callers.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:11 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register during MMIO
On ARM64 register index of 31 corresponds to both zero register and SP.
However, all memory access instructions, use ZR as transfer register. SP
is used only as a base register in indirect memory addressing, or by
register-register arithmetics, which cannot be trapped here.
Correct emulation is achieved by introducing new register accessor
functions, which can do special handling for reg_num == 31. These new
accessors intentionally do not rely on old vcpu_reg() on ARM64, because
it is to be removed. Since the affected code is shared by both ARM
flavours, implementations of these accessors are also added to ARM32 code.
This patch fixes setting MMIO register to a random value (actually SP)
instead of zero by something like:
*((volatile int *)reg) = 0;
compilers tend to generate "str wzr, [xx]" here
[Marc: Fixed 32bit splat]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Ilya Dryomov [Fri, 27 Nov 2015 18:23:24 +0000 (19:23 +0100)]
rbd: don't put snap_context twice in rbd_queue_workfn()
Commit 4e752f0ab0e8 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
Triggering a warning when trying to sample the vblank timestamp for a
non-existing pipe. There's a few ways to fix this:
- Open-code the old behaviour, which just enshrines this slight
breakage of the userspace ABI.
- Revert Mario's commit and again inflict broken timestamps, again not
pretty.
- Fix this for real by delaying the pageflip TS until the next vblank
interrupt, thereby making it accurate.
This patch implements the third option. Since having a page flip
interrupt that happens when the pageflip gets armed and not when it
completes in the next vblank seems to be fairly common (older i915 hw
works very similarly) create a new helper to arm vblank events for
such drivers.
v2 (Mario Kleiner):
- Fix function prototypes in drmP.h
- Add missing vblank_put() for pageflip completion without
pageflip event.
- Initialize sequence number for queued pageflip event to avoid
trouble in drm_handle_vblank_events().
- Remove dead code and spelling fix.
v3 (Mario Kleiner):
- Add a signed-off-by and cc stable tag per Ilja's advice.
v4 (Thierry Reding):
- Fix kerneldoc typo, discovered by Michel Dänzer
- Rearrange tags and changelog
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=106431 Cc: Thierry Reding <treding@nvidia.com> Cc: Mario Kleiner <mario.kleiner.de@gmail.com> Acked-by: Ben Skeggs <bskeggs@redhat.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: stable@vger.kernel.org # v4.3 Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 4 Dec 2015 02:26:29 +0000 (12:26 +1000)]
Merge tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm crtc, plane, parallel panel, and TV encoder fixes
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
* tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux:
drm: imx: imx-tve: Fix module autoload for OF platform driver
drm: imx: convert to drm_crtc_send_vblank_event()
GPU-DRM-IMX: Delete an unnecessary check before drm_fbdev_cma_restore_mode()
drm/imx: Remove of_node assignment from ipuv3-crtc driver probe
gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports
gpu: ipu-v3: Remove reg_offset field
gpu: ipu-v3: drop unused dmfc field from client platform data
drm/imx: parallel-display: allow to determine bus format from the connected panel
drm/imx: ipuv3-crtc: Return error if ipu_plane_init() fails for primary plane
drm/imx: switch to universal planes
Dave Airlie [Fri, 4 Dec 2015 02:23:13 +0000 (12:23 +1000)]
Merge tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Another batch of drm/i915 fixes for v4.4, on top of the ones from
earlier this week. One timeout handling regression fix from Chris, and
backport of five patches from our -next to fix a power management
related HDMI hotplug regression.
* tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/i915: Check the timeout passed to i915_wait_request
Eric Anholt [Tue, 1 Dec 2015 17:39:31 +0000 (09:39 -0800)]
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
It looks like these meant to be unreffing the
of_parse_phandle_with_args() node, since the error paths above it
don't do of_node_put. That function returns a new ref in pd_args.np,
though, not a new ref on dev->of_node. Also, it would have leaked the
ref in the success case.
Fixes "ERROR: Bad of_node_put()" on bcm2835 in the -EPROBE_DEFER case.
Fixes: aa42240ab254 (PM / Domains: Add generic OF-based PM domain look-up) Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Kevin Hilman <khilman@linaro.org> Cc: 3.18+ <stable@vger.kernel.org> # 3.18+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 3 Dec 2015 23:45:16 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes from this series. The most important here is a
regression fix for an issue that some folks would hit in blk-merge.c,
and the NVMe queue depth limit for the screwed up Apple "nvme"
controller.
In more detail, this pull request contains:
- a set of fixes for null_blk, including a fix for a few corner cases
where we could hang the device. From Arianna and Paolo.
- lightnvm:
- A build improvement from Keith.
- Update the qemu pci id detection from Matias.
- Error handling fixes for leaks and other little fixes from
Sudip and Wenwei.
- fix from Eric where BLKRRPART would not return EBUSY for whole
device mounts, only when partitions were mounted.
- fix from Jan Kara, where EOF O_DIRECT reads would return
negatively.
- remove check for rq_mergeable() when checking limits for cloned
requests. The check doesn't make any sense. It's assuming that
since NOMERGE is set on the request that we don't have to
recalculate limits since the request didn't change, but that's not
true if the request has been redirected. From Hannes.
- correctly get the bio front segment value set for single segment
bio's, fixing a BUG() in blk-merge. From Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: temporary fix for Apple controller reset
null_blk: change type of completion_nsec to unsigned long
null_blk: guarantee device restart in all irq modes
null_blk: set a separate timer for each command
blk-merge: fix computing bio->bi_seg_front_size in case of single segment
direct-io: Fix negative return from dio read beyond eof
block: Always check queue limits for cloned requests
lightnvm: missing nvm_lock acquire
lightnvm: unconverted ppa returned in get_bb_tbl
lightnvm: refactor and change vendor id for qemu
lightnvm: do device max sectors boundary check first
lightnvm: fix ioctl memory leaks
lightnvm: free memory when gennvm register fails
lightnvm: Simplify config when disabled
Return EBUSY from BLKRRPART for mounted whole-dev fs
Linus Torvalds [Thu, 3 Dec 2015 23:23:17 +0000 (15:23 -0800)]
Merge tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"During the merge window I added a new file that is used to filter
trace events on pids. It filters all events where only tasks with
their pid in that file exists. It also handles the sched_switch and
sched_wakeup trace events where the current task does not have its pid
in the file, but the task either being switched to or awaken does.
Unfortunately, I forgot about sched_wakeup_new and sched_waking. Both
of these tracepoints use the same class as the sched_wakeup
tracepoint, and they too should be included in what gets filtered by
the set_event_pid file"
* tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add sched_wakeup_new and sched_waking tracepoints for pid filter
David S. Miller [Thu, 3 Dec 2015 20:56:22 +0000 (15:56 -0500)]
Merge tag 'mac80211-for-davem-2015-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A small set of fixes for 4.4:
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jérôme Pouiller [Thu, 3 Dec 2015 09:02:35 +0000 (10:02 +0100)]
net: phy: reset only targeted phy
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 2 Dec 2015 06:54:08 +0000 (01:54 -0500)]
bnxt_en: Setup uc_list mac filters after resetting the chip.
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Huang [Wed, 2 Dec 2015 06:54:07 +0000 (01:54 -0500)]
bnxt_en: enforce proper storing of MAC address
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Huang [Wed, 2 Dec 2015 06:54:06 +0000 (01:54 -0500)]
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: lpc_eth: remove irq > NR_IRQS check from probe()
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.
A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.
Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.
Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.
A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Cong Wang <cwang@twopensource.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 1 Dec 2015 17:33:36 +0000 (18:33 +0100)]
openvswitch: fix hangup on vxlan/gre/geneve device deletion
Each openvswitch tunnel vport (vxlan,gre,geneve) holds a reference
to the underlying tunnel device, but never released it when such
device is deleted.
Deleting the underlying device via the ip tool cause the kernel to
hangup in the netdev_wait_allrefs() loop.
This commit ensure that on device unregistration dp_detach_port_notify()
is called for all vports that hold the device reference, properly
releasing it.
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device") Fixes: b2acd1dc3949 ("openvswitch: Use regular GRE net_device instead of vport") Fixes: 6b001e682e90 ("openvswitch: Use Geneve device.") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Flavio Leitner <fbl@sysclose.org> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 1 Dec 2015 15:31:08 +0000 (16:31 +0100)]
ipv4: igmp: Allow removing groups from a removed interface
When a multicast group is joined on a socket, a struct ip_mc_socklist
is appended to the sockets mc_list containing information about the
joined group.
If the interface is hot unplugged, this entry becomes stale. Prior to
commit 52ad353a5344f ("igmp: fix the problem when mc leave group") it
was possible to remove the stale entry by performing a
IP_DROP_MEMBERSHIP, passing either the old ifindex or ip address on
the interface. However, this fix enforces that the interface must
still exist. Thus with time, the number of stale entries grows, until
sysctl_igmp_max_memberships is reached and then it is not possible to
join and more groups.
The previous patch fixes an issue where a IP_DROP_MEMBERSHIP is
performed without specifying the interface, either by ifindex or ip
address. However here we do supply one of these. So loosen the
restriction on device existence to only apply when the interface has
not been specified. This then restores the ability to clean up the
stale entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 52ad353a5344f "(igmp: fix the problem when mc leave group") Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 1 Dec 2015 15:20:07 +0000 (07:20 -0800)]
ipv6: sctp: implement sctp_v6_destroy_sock()
Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets.
We need to call inet6_destroy_sock() to properly release
inet6 specific fields.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Mon, 30 Nov 2015 22:24:07 +0000 (14:24 -0800)]
arm64: bpf: add 'store immediate' instruction
aarch64 doesn't have native store immediate instruction, such operation
has to be implemented by the below instruction sequence:
Load immediate to register
Store register
Signed-off-by: Yang Shi <yang.shi@linaro.org> CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 3 Dec 2015 05:53:57 +0000 (21:53 -0800)]
ipv6: kill sk_dst_lock
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/neighbour: fix crash at dumping device-agnostic proxy entries
Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Fixes: 84920c1420e2 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2") Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported that the user could trigger a kernel warning by
using a large len value for getsockopt SCTP_GET_LOCAL_ADDRS, as that
value directly affects the value used as a kmalloc() parameter.
This patch thus switches the allocation flags from all user-controllable
kmalloc size to GFP_USER to put some more restrictions on it and also
disables the warn, as they are not necessary.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: convert sack_needed and sack_generation to bits
They don't need to be any bigger than that and with this we start a new
bitfield for tracking association runtime stuff, like zero window
situation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 03:37:57 +0000 (19:37 -0800)]
ipv6: add complete rcu protection around np->opt
This patch addresses multiple problems :
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid never succeeding kmalloc with order >= MAX_ORDER check that
elem->value_size and computed elem_size are within limits for both hash and
array type maps.
Also add __GFP_NOWARN to kmalloc(value_size | elem_size) to avoid OOM warnings.
Note kmalloc(key_size) is highly unlikely to trigger OOM, since key_size <= 512,
so keep those kmalloc-s as-is.
Large value_size can cause integer overflows in elem_size and map.pages
formulas, so check for that as well.
Fixes: aaac3ba95e4c ("bpf: charge user for creation of BPF maps and programs") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 04:35:22 +0000 (23:35 -0500)]
Merge branch 'mvneta-fixes'
Marcin Wojtas says:
====================
Marvell Armada XP/370/38X Neta fixes
I'm sending v4 with corrected commit log of the last patch, in order to
avoid possible conflicts between the branches as suggested by Gregory
Clement.
Best regards,
Marcin Wojtas
Changes from v4:
* Correct commit log of patch 6/6
Changes from v2:
* Style fixes in patch updating mbus protection
* Remove redundant stable notifications except for patch 4/6
Changes from v1:
* update MBUS windows access protection register once, after whole loop
* add fixing value of MVNETA_RXQ_INTR_ENABLE_ALL_MASK
* add fixing error path for skb_build()
* add possibility of setting custom TX IP checksum limit in DT property
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:46 +0000 (13:27 +0100)]
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
The Ethernet controller found in the Armada 38x SoC's family support
TCP/IP checksumming with frame sizes larger than 1600 bytes, however
only on port 0.
This commit enables it by setting 'tx-csum-limit' to 9800B in
'ethernet@70000' node.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:45 +0000 (13:27 +0100)]
net: mvneta: enable setting custom TX IP checksum limit
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:44 +0000 (13:27 +0100)]
net: mvneta: fix error path for building skb
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Acked-by: Simon Guinot <simon.guinot@sequanux.org> Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:43 +0000 (13:27 +0100)]
net: mvneta: fix bit assignment for RX packet irq enable
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:42 +0000 (13:27 +0100)]
net: mvneta: fix bit assignment in MVNETA_RXQ_CONFIG_REG
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:41 +0000 (13:27 +0100)]
net: mvneta: add configuration for MBUS windows access protection
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 3 Dec 2015 00:45:56 +0000 (16:45 -0800)]
Merge tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix for the core here, we weren't reinitialising the
actual transferred length in messages when they get reused which meant
that we'd just keep adding to the length if a message is reused. This
has limited impact since it's only used in error handling cases but
will really mess anything that tries to use it up when it triggers.
As ever there's a small collection of driver specific fixes too"
* tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bugfix: spi_message.transfer_length does not get reset
spi: pl022: handle EPROBE_DEFER for dma
spi: bcm63xx: use correct format string for printing a resource
spi: mediatek: single device does not require cs_gpios
spi: Add missing kerneldoc description for parameter
cpufreq: use last policy after online for drivers with ->setpolicy
For cpufreq drivers which use setpolicy interface, after offline->online
the policy is set to default. This can be reproduced by setting the
default policy of intel_pstate or longrun to ondemand and then change to
"performance". After offline and online, the setpolicy will be called with
the policy=ondemand.
For drivers using governors this condition is handled by storing
last_governor, during offline and restoring during online. The same should
be done for drivers using setpolicy interface. Storing last_policy during
offline and restoring during online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.
Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.
Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.
Fixes: 3b79af973cf4 ("mac80211: stop using pointers as userspace cookies") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.
If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.
Cc: stable@vger.kernel.org Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eliad Peller [Tue, 17 Nov 2015 08:24:40 +0000 (10:24 +0200)]
mac80211: don't teardown sdata on sdata stop
Interfaces are being initialized (setup) on addition,
and torn down on removal.
However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.
Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch series contains fixes for various issues observed
with BGX and NIC drivers.
Changes from v1:
- Fixed comment syle in the first patch of the series
- Removed 'Increase transmit queue length' patch from the series,
will recheck if it's a driver or system issue and resubmit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Wed, 2 Dec 2015 10:06:17 +0000 (15:36 +0530)]
net: thunderx: Enable BGX LMAC's RX/TX only after VF is up
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Wed, 2 Dec 2015 10:06:16 +0000 (15:36 +0530)]
net: thunderx: Switchon carrier only upon interface link up
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: Wait for delayed work to finish before destroying it
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: Force to load octeon-mdio before bgx driver.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolai Hähnle [Wed, 2 Dec 2015 16:35:12 +0000 (17:35 +0100)]
drm/amdgpu: fix race condition in amd_sched_entity_push_job
As soon as we leave the spinlock after the job has been added to the job
queue, we can no longer rely on the job's data to be available.
I have seen a null-pointer dereference due to sched == NULL in
amd_sched_wakeup via amd_sched_entity_push_job and
amd_sched_ib_submit_kernel_helper. Since the latter initializes
sched_job->sched with the address of the ring scheduler, which is
guaranteed to be non-NULL, this race appears to be a likely culprit.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=93079 Reviewed-by: Christian König <christian.koenig@amd.com>
Linus Torvalds [Wed, 2 Dec 2015 19:05:34 +0000 (11:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- regression fix for hid-lg driver from Benjamin Tissoires
- quirk for Logitech G710+ from Jimmy Berry
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: lg: restrict filtering out of first interface to G29 only
HID: usbhid: add Logitech G710+ keyboard quirk NOGET
Linus Torvalds [Wed, 2 Dec 2015 19:00:05 +0000 (11:00 -0800)]
Merge tag 'pinctrl-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol fixes from Linus Walleij:
"These are some v4.4 pin control fixes:
- Drop a redundant if-clause from Kconfig
- Fix a missing of_node_put() memory leak in the Freescale i.MX
driver
- Fix 64bit compilation of the Qualcomm SSBI driver.
- Fix a logic inversion in the Mediatek driver.
- Fix a compilation error for the odd one off in the Super-H instance
of the SH PFC driver"
* tag 'pinctrl-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sh-pfc: sh7734: Add missing cfg macro parameter to fix build
pinctrl: mediatek: Add get_direction support.
pinctrl: fix qcom ssbi drivers for 64-bit compilation
pinctrl: imx1-core: add missing of_node_put
pinctrl: remove redundant if conditional from Kconfig
Linus Torvalds [Wed, 2 Dec 2015 18:54:03 +0000 (10:54 -0800)]
Merge tag 'gpio-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.4 series:
- Fix a bunch of possible NULL references found by Coccinelle
jockeys.
- Stop creating Tegra's debugfs on everything and its dog. This is
an ARM multiplatform kernel issue.
- Fix an oops in gpiolib for NULL names on named GPIOs.
- Fix a complex OMAP1 bug in the OMAP driver"
* tag 'gpio-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: drop omap1 mpuio specific irq_mask/unmask callbacks
gpiolib: fix oops, if gpio name is NULL
gpio-tegra: Do not create the debugfs entry by default
gpio: palmas: fix a possible NULL dereference
gpio: syscon: fix a possible NULL dereference
gpio: 74xx: fix a possible NULL dereference
Paolo Abeni [Mon, 30 Nov 2015 11:31:43 +0000 (12:31 +0100)]
openvswitch: properly refcount vport-vxlan module
After 614732eaa12d, no refcount is maintained for the vport-vxlan module.
This allows the userspace to remove such module while vport-vxlan
devices still exist, which leads to later oops.
v1 -> v2:
- move vport 'owner' initialization in ovs_vport_ops_register()
and make such function a macro
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Imre Deak [Fri, 27 Nov 2015 16:55:29 +0000 (18:55 +0200)]
drm/i915: take a power domain reference while checking the HDMI live status
There are platforms that don't need the full GMBUS power domain (BXT)
while others do (PCH, VLV/CHV). For optimizing this we would need to add
a new power domain, but it's not clear how much we would benefit given
the short time we hold the reference. So for now let's keep things
simple.
This fixes a regression introduced in
commit 237ed86c693d8a8e4db476976aeb30df4deac74b
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Tue Sep 15 09:44:20 2015 +0530
drm/i915: Check live status before reading edid
v2:
- fix commit message, PCH won't take any redundant power resource after
this change (Ville)
Imre Deak [Fri, 27 Nov 2015 16:55:28 +0000 (18:55 +0200)]
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
MISSING_CASE() would have been useful to track down a recent problem in
intel_display_port_aux_power_domain(), so add it there and a few related
helpers. This was also suggested by Ville in his review of the latest
DMC/DC changes, we forgot to address that.
Imre Deak [Fri, 27 Nov 2015 16:55:27 +0000 (18:55 +0200)]
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
Due to the current sharing of the DDI encoder between DP and HDMI
connectors we can run the DP detection after the HDMI detection has
already set the shared encoder's type. For now solve this keeping the
current behavior and running the detection in this case too. For a proper
solution Ville suggested to split the encoder into an HDMI and DP one, that
can be done as a follow-up.
This issue triggers the WARN in intel_display_port_aux_power_domain() and
was introduced in:
commit 25f78f58e5bfb46a270ce4d690fb49dc104558b1
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Nov 16 15:01:04 2015 +0100
drm/i915: Clean up AUX power domain handling
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com> CC: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 651174a4 (Imre)] Signed-off-by: Imre Deak <imre.deak@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-4-git-send-email-imre.deak@intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Fri, 27 Nov 2015 16:55:26 +0000 (18:55 +0200)]
drm/i915: Introduce a gmbus power domain
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
Ville Syrjälä [Fri, 27 Nov 2015 16:55:25 +0000 (18:55 +0200)]
drm/i915: Clean up AUX power domain handling
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Imre Deak [Mon, 30 Nov 2015 19:02:55 +0000 (21:02 +0200)]
PCI / PM: Tune down retryable runtime suspend error messages
The runtime PM core doesn't treat EBUSY and EAGAIN retvals from the driver
suspend hooks as errors, but they still show up as errors in dmesg. Tune
them down. See rpm_suspend() for details of handling these return values.
Note that we use dev_dbg() for the retryable retvals, so after this
change you'll need either CONFIG_DYNAMIC_DEBUG or CONFIG_PCI_DEBUG
for them to show up in the log.
One problem caused by this was noticed by Daniel: the i915 driver
returns EAGAIN to signal a temporary failure to suspend and as a request
towards the RPM core for scheduling a suspend again. This is a normal
event, but the resulting error message flags a breakage during the
driver's automated testing which parses dmesg and picks up the error.
Reported-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://bugs.freedesktop.org/show_bug.cgi?id=92992 Signed-off-by: Imre Deak <imre.deak@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ulf Hansson [Wed, 2 Dec 2015 13:08:27 +0000 (14:08 +0100)]
PM / Domains: Validate cases of a non-bound driver in genpd governor
Recently genpd removed the requirement of a having a driver bound for its
attached devices to allow genpd to power off. That change should also have
removed a corresponding validation in the governor, let's correct that.
Fixes: 298cd0f08801 (PM / Domains: Remove dev->driver check for runtime) Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dan Carpenter [Tue, 1 Dec 2015 08:58:40 +0000 (11:58 +0300)]
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
We renamed drivers/acpi/video.c to drivers/acpi/acpi_video.c in commit 14ca7a47d0ab ('acpi-video-detect: video: Make video_detect code part of
the video module').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hanjun Guo [Wed, 2 Dec 2015 07:44:22 +0000 (15:44 +0800)]
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
In commit 60ba032ed76e ("ACPI / property: Drop size_prop from
acpi_dev_get_property_reference()"), the argument "const char *cells_name"
was dropped, but forgot to update the stub function in no-ACPI case,
it will lead to compile error when CONFIG_ACPI=n, easliy remove
"const char *cells_name" to fix it.
Fixes: 60ba032ed76e "ACPI / property: Drop size_prop from acpi_dev_get_property_reference()" Reported-by: Kejian Yan <yankejian@huawei.com> Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Daniel Borkmann [Mon, 30 Nov 2015 12:02:56 +0000 (13:02 +0100)]
bpf, array: fix heap out-of-bounds access when updating elements
During own review but also reported by Dmitry's syzkaller [1] it has been
noticed that we trigger a heap out-of-bounds access on eBPF array maps
when updating elements. This happens with each map whose map->value_size
(specified during map creation time) is not multiple of 8 bytes.
In array_map_alloc(), elem_size is round_up(attr->value_size, 8) and
used to align array map slots for faster access. However, in function
array_map_update_elem(), we update the element as ...
... where we access 'value' out-of-bounds, since it was allocated from
map_update_elem() from syscall side as kmalloc(map->value_size, GFP_USER)
and later on copied through copy_from_user(value, uvalue, map->value_size).
Thus, up to 7 bytes, we can access out-of-bounds.
Same could happen from within an eBPF program, where in worst case we
access beyond an eBPF program's designated stack.
Since 1be7f75d1668 ("bpf: enable non-root eBPF programs") didn't hit an
official release yet, it only affects priviledged users.
In case of array_map_lookup_elem(), the verifier prevents eBPF programs
from accessing beyond map->value_size through check_map_access(). Also
from syscall side map_lookup_elem() only copies map->value_size back to
user, so nothing could leak.
[1] http://github.com/google/syzkaller
Fixes: 28fbcfa08d8e ("bpf: add array type of eBPF maps") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Stone [Mon, 16 Nov 2015 12:50:21 +0000 (12:50 +0000)]
drm/rockchip: Use CRTC vblank event interface
Passing -1 as the pipe for vblank events now triggers a WARN_ON, but had
previously made multi-screen unusable anyway. Pass the correct pipe to
the event-send function, and use the new API to make this a bit easier
for us.
Fixes WARN present since cc1ef118fc for every pageflip event sent:
[ 209.549969] ------------[ cut here ]------------
[ 209.554592] WARNING: CPU: 3 PID: 238 at drivers/gpu/drm/drm_irq.c:924 drm_vblank_count_and_time+0x80/0x88 [drm]()
[ 209.564832] Modules linked in: [...]
[ 209.612401] CPU: 3 PID: 238 Comm: irq/41-ff940000 Tainted: G W 4.3.0-rc6+ #71
[ 209.620647] Hardware name: Rockchip (Device Tree)
[ 209.625348] [<c001bb80>] (unwind_backtrace) from [<c001615c>] (show_stack+0x20/0x24)
[ 209.633079] [<c001615c>] (show_stack) from [<c02b2c50>] (dump_stack+0x8c/0x9c)
[ 209.640289] [<c02b2c50>] (dump_stack) from [<c0052e88>] (warn_slowpath_common+0x94/0xc4)
[ 209.648364] [<c0052e88>] (warn_slowpath_common) from [<c0052f74>] (warn_slowpath_null+0x2c/0x34)
[ 209.657139] [<c0052f74>] (warn_slowpath_null) from [<bf17dc30>] (drm_vblank_count_and_time+0x80/0x88 [drm])
[ 209.666875] [<bf17dc30>] (drm_vblank_count_and_time [drm]) from [<bf17e484>] (drm_send_vblank_event+0x74/0x7c [drm])
[ 209.677385] [<bf17e484>] (drm_send_vblank_event [drm]) from [<bf4c1144>] (vop_win_state_complete+0x4c/0x70 [rockchip_drm_vop])
[ 209.688757] [<bf4c1144>] (vop_win_state_complete [rockchip_drm_vop]) from [<bf4c3bdc>] (vop_isr_thread+0x170/0x1d4 [rockchip_drm_vop])
[ 209.700822] [<bf4c3bdc>] (vop_isr_thread [rockchip_drm_vop]) from [<c00ab93c>] (irq_thread_fn+0x2c/0x50)
[ 209.710284] [<c00ab93c>] (irq_thread_fn) from [<c00abcac>] (irq_thread+0x13c/0x188)
[ 209.717927] [<c00abcac>] (irq_thread) from [<c00723c8>] (kthread+0xec/0x104)
[ 209.724965] [<c00723c8>] (kthread) from [<c0011638>] (ret_from_fork+0x14/0x3c)
[ 209.732171] ---[ end trace 0690bc604f5d535d ]---
Liu Jiang [Fri, 27 Nov 2015 03:12:33 +0000 (11:12 +0800)]
x86/PCI/ACPI: Fix regression caused by commit 4d6b4e69a245
Commit 4d6b4e69a245 ("x86/PCI/ACPI: Use common interface to support
PCI host bridge") converted x86 to use the common interface
acpi_pci_root_create, but the conversion missed on code piece in
arch/x86/pci/bus_numa.c, which causes regression on some legacy
AMD platforms as reported by Arthur Marsh <arthur.marsh@internode.on.net>.
The root causes is that acpi_pci_root_create() fails to insert
host bridge resources into iomem_resource/ioport_resource because
x86_pci_root_bus_resources() has already inserted those resources.
So change x86_pci_root_bus_resources() to not insert resources into
iomem_resource/ioport_resource.
Fixes: 4d6b4e69a245 ("x86/PCI/ACPI: Use common interface to support PCI host bridge") Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Reported-and-tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl> Reported-and-tested-by: Keith Busch <keith.busch@intel.com> Reported-and-tested-by: Hans de Bruin <jmdebruin@xmsnet.nl> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dominik Behr [Tue, 10 Nov 2015 09:59:10 +0000 (17:59 +0800)]
drm/rockchip: vop: fix window origin calculation
VOP_WINx_DSP_ST does not require subtracting 1 from the values written to
it. It actually causes the screen to be shifted by one pixel.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com> Tested-by: Yakir Yang <ykk@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Dominik Behr <dbehr@chromium.org> Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
projects / linux-beck.git / log