A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.
Mathew pointed out:
|
| We're supposed to be resetting trampoline_phys_low and
| trampoline_phys_high here, which are two 16-bit values.
| Writing 64 bits is definitely going to overwrite space
| that we're not supposed to be touching.
|
So limit the area modified to u32.
Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Matthew Garrett <mjg@redhat.com>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jochen Friedrich <jochen@scram.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Current refcounttree codes actually didn't writeback the new pages out in
write-back mode, due to a bug of always passing a ZERO number of clusters
to 'ocfs2_cow_sync_writeback', the patch tries to pass a proper one in.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Joel Becker <jlbec@evilplan.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
does not take into account that the remaining data length can be less
than sg_dma_len(sg). In that case, running_total can end up being
greater than the total data length, so an extra TRB is counted.
Changing the expression to
while (running_total < sg_dma_len(sg) && running_total < temp)
fixes that.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
are incorrect, because running_total can never be zero, so the if()
expression will never be true. I think the intention was that
running_total be in the range of 0 to TRB_MAX_BUFF_SIZE-1, not 1
to TRB_MAX_BUFF_SIZE. So adding a
running_total &= TRB_MAX_BUFF_SIZE - 1;
fixes the problem.
This patch should be queued for stable kernels back to 2.6.31.
[PG: 34 doesn't have count_isoc_trbs_needed() hence this has
only two of the three upstream running_total changes.]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This makes it easier to spot some problems, which will be fixed by the
next patch in the series. Also change dev_dbg to dev_err in
check_trb_math(), so any math errors will be visible even when running
with debug disabled.
Note: This patch changes the expressions containing
"((1 << TRB_MAX_BUFF_SHIFT) - 1)" to use the equivalent
"(TRB_MAX_BUFF_SIZE - 1)". No change in behavior is intended for
those expressions.
This patch should be queued for stable kernels back to 2.6.31.
[PG: 34 doesn't have count_isoc_trbs_needed() hence this has
one less instance to change vs. the originating release]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change the BUGs in xhci_find_new_dequeue_state() to WARN_ONs, to avoid
bringing down the box if one of them is hit
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
On some SB800 systems polarity for IOAPIC pin2 is wrongly
specified as low active by BIOS. This caused system hangs after
resume from S3 when HPET was used in one-shot mode on such
systems because a timer interrupt was missed (HPET signal is
high active).
'mdp' devices are md devices with preallocated device numbers
for partitions. As such it is possible to mknod and open a partition
before opening the whole device.
this causes md_probe() to be called with a device number of a
partition, which in-turn calls mddev_find with such a number.
However mddev_find expects the number of a 'whole device' and
does the wrong thing with partition numbers.
So add code to mddev_find to remove the 'partition' part of
a device number and just work with the 'whole device'.
This patch addresses https://bugzilla.kernel.org/show_bug.cgi?id=28652
Reported-by: hkmaly@bigfoot.com Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating LDM partitions (in fs/partitions/ldm.c) contains
a bug that causes a kernel oops on certain corrupted LDM partitions. A
kernel subsystem seems to crash, because, after the oops, the kernel no
longer recognizes newly connected storage devices.
The patch changes ldm_parse_vmdb() to Validate the value of vblk_size.
Signed-off-by: Timo Warns <warns@pre-sense.de> Cc: Eugene Teo <eugeneteo@kernel.sg> Acked-by: Richard Russon <ldm@flatcap.org> Cc: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In several places, an epoll fd can call another file's ->f_op->poll()
method with ep->mtx held. This is in general unsafe, because that other
file could itself be an epoll fd that contains the original epoll fd.
The code defends against this possibility in its own ->poll() method using
ep_call_nested, but there are several other unsafe calls to ->poll
elsewhere that can be made to deadlock. For example, the following simple
program causes the call in ep_insert recursively call the original fd's
->poll, leading to deadlock:
#include <unistd.h>
#include <sys/epoll.h>
int main(void) {
int e1, e2, p[2];
struct epoll_event evt = {
.events = EPOLLIN
};
On insertion, check whether the inserted file is itself a struct epoll,
and if so, do a recursive walk to detect whether inserting this file would
create a loop of epoll structures, which could lead to deadlock.
[nelhage@ksplice.com: Use epmutex to serialize concurrent inserts] Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Nelson Elhage <nelhage@ksplice.com> Reported-by: Nelson Elhage <nelhage@ksplice.com> Tested-by: Nelson Elhage <nelhage@ksplice.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
I picked up a new Sierra usb 308 (At&t Shockwave) on 2/2011 and the vendor code
is 0x0f3d
Looking up vendor and product id's I see:
0f3d Airprime, Incorporated
0112 CDMA 1xEVDO PC Card, PC 5220
Sierra and Airprime are somehow related and I'm guessing the At&t usb 308 might
be have some common hardware with the AirPrime SL809x.
Signed-off-by: Jon Thomas <jthomas@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
My Galaxy Spica needs this quirk when in modem mode, otherwise
it causes endless USB bus resets and is unusable in this mode.
Unfortunately Samsung decided to reuse ID of its old CDMA phone SGH-I500
for the modem part.
That's why in addition to this patch the visor driver must be prevented
from binding to SPH-I500 ID, so ACM driver can do that.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[USB]Add Samsung SGH-I500/Android modem ID switch to visor driver
Samsung decided to reuse USB ID of its old CDMA phone SGH-I500 for the
modem part of some of their Android phones. At least Galaxy Spica
is affected.
This modem needs ACM driver and does not work with visor driver which
binds the conflicting ID for SGH-I500.
Because SGH-I500 is pretty an old hardware its best to add switch to
visor
driver in cause somebody still wants to use that phone with Linux.
Note that this is needed only when using the Android phone as modem,
not in USB storage or ADB mode.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch (as1448) adds a quirks entry for the Keytouch QWERTY Panel
firmware, used in the IEC 60945 keyboard. This device crashes during
enumeration when the computer asks for its configuration string
descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: kholis <nur.kholis.majid@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.
The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With CONFIG_SHIRQ_DEBUG=y we call a newly installed interrupt handler
in request_threaded_irq().
The original implementation (commit a304e1b8) called the handler
_BEFORE_ it was installed, but that caused problems with handlers
calling disable_irq_nosync(). See commit 377bf1e4.
It's braindead in the first place to call disable_irq_nosync in shared
handlers, but ....
Moving this call after we installed the handler looks innocent, but it
is very subtle broken on SMP.
Interrupt handlers rely on the fact, that the irq core prevents
reentrancy.
Now this debug call violates that promise because we run the handler
w/o the IRQ_INPROGRESS protection - which we cannot apply here because
that would result in a possibly forever masked interrupt line.
A concurrent real hardware interrupt on a different CPU results in
handler reentrancy and can lead to complete wreckage, which was
unfortunately observed in reality and took a fricking long time to
debug.
Leave the code here for now. We want this debug feature, but that's
not easy to fix. We really should get rid of those
disable_irq_nosync() abusers and remove that function completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
https://bugs.launchpad.net/bugs/613873
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Acked-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently we return 0 in swsusp_alloc() when alloc_image_page() fails.
Fix that. Also remove unneeded "error" variable since the only
useful value of error is -ENOMEM.
[rjw: Fixed up the changelog and changed subject.]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 7124fe0a5b619d65b739477b3b55a20bf805b06d ("xfs: validate untrusted inode
numbers during lookup") changes the inode lookup code to do btree lookups for
untrusted inode numbers. This change made an invalid assumption about the
alignment of inodes and hence incorrectly calculated the first inode in the
cluster. As a result, some inode numbers were being incorrectly considered
invalid when they were actually valid.
The issue was not picked up by the xfstests suite because it always runs fsr
and dump (the two utilities that utilise the bulkstat interface) on cache hot
inodes and hence the lookup code in the cold cache path was not sufficiently
exercised to uncover this intermittent problem.
Fix the issue by relaxing the btree lookup criteria and then checking if the
record returned contains the inode number we are lookup for. If it we get an
incorrect record, then the inode number is invalid.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The block number comes from bulkstat based inode lookups to shortcut
the mapping calculations. We ar enot able to trust anything from
bulkstat, so drop the block number as well so that the correct
lookups and mappings are always done.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Inode numbers may come from somewhere external to the filesystem
(e.g. file handles, bulkstat information) and so are inherently
untrusted. Rename the flag we use for these lookups to make it
obvious we are doing a lookup of an untrusted inode number and need
to verify it completely before trying to read it from disk.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When we decode a handle or do a bulkstat lookup, we are using an
inode number we cannot trust to be valid. If we are deleting inode
chunks from disk (default noikeep mode), then we cannot trust the on
disk inode buffer for any given inode number to correctly reflect
whether the inode has been unlinked as the di_mode nor the
generation number may have been updated on disk.
This is due to the fact that when we delete an inode chunk, we do
not write the clusters back to disk when they are removed - instead
we mark them stale to avoid them being written back potentially over
the top of something that has been subsequently allocated at that
location. The result is that we can have locations of disk that look
like they contain valid inodes but in reality do not. Hence we
cannot simply convert the inode number to a block number and read
the location from disk to determine if the inode is valid or not.
As a result, and XFS_IGET_BULKSTAT lookup needs to actually look the
inode up in the inode allocation btree to determine if the inode
number is valid or not.
It should be noted even on ikeep filesystems, there is the
possibility that blocks on disk may look like valid inode clusters.
e.g. if there are filesystem images hosted on the filesystem. Hence
even for ikeep filesystems we really need to validate that the inode
number is valid before issuing the inode buffer read.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The non-coherent bulkstat versionsthat look directly at the inode
buffers causes various problems with performance optimizations that
make increased use of just logging inodes. This patch makes bulkstat
always use iget, which should be fast enough for normal use with the
radix-tree based inode cache introduced a while ago.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In prepare_kernel_cred() since 2.6.29, put_cred(new) is called without
assigning new->usage when security_prepare_creds() returned an error. As a
result, memory for new and refcount for new->{user,group_info,tgcred} are
leaked because put_cred(new) won't call __put_cred() unless old->usage == 1.
Fix these leaks by assigning new->usage (and new->subscribers which was added
in 2.6.32) before calling security_prepare_creds().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In cred_alloc_blank() since 2.6.32, abort_creds(new) is called with
new->security == NULL and new->magic == 0 when security_cred_alloc_blank()
returns an error. As a result, BUG() will be triggered if SELinux is enabled
or CONFIG_DEBUG_CREDENTIALS=y.
If CONFIG_DEBUG_CREDENTIALS=y, BUG() is called from __invalid_creds() because
cred->magic == 0. Failing that, BUG() is called from selinux_cred_free()
because selinux_cred_free() is not expecting cred->security == NULL. This does
not affect smack_cred_free(), tomoyo_cred_free() or apparmor_cred_free().
Fix these bugs by
(1) Set new->magic before calling security_cred_alloc_blank().
(2) Handle null cred->security in creds_are_invalid() and selinux_cred_free().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In get_empty_filp() since 2.6.29, file_free(f) is called with f->f_cred == NULL
when security_file_alloc() returned an error. As a result, kernel will panic()
due to put_cred(NULL) call within RCU callback.
Fix this bug by assigning f->f_cred before calling security_file_alloc().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.
What happens is that get_task_cred() can race with commit_creds():
However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.
If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.
We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.
Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:
If the guest domain has been suspend/resumed or migrated, then the
system clock backing the pvclock clocksource may revert to a smaller
value (ie, can be non-monotonic across the migration/save-restore).
Make sure we zero last_value in that case so that the domain
continues to see clock updates.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com> Tested-by: Yury Siamashka <yurand2@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If ocfs2_live_connection_list is empty, ocfs2_connection_find() will return
a pointer to the LIST_HEAD, cast as a ocfs2_live_connection. This can cause
an oops when ocfs2_control_send_down() dereferences c->oc_conn:
Fix by explicitly returning NULL if no match is found.
Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There's a branch at the end of this function that
is supposed to normalize the return value with what
the mid-layer expects. In this one case, we get it wrong.
Also increase the verbosity of the INFO level printk
at the end of mptscsih_abort to include the actual return value
and the scmd->serial_number. The reason being success
or failure is actually determined by the state of
the internal tag list when a TMF is issued, and not the
return value of the TMF cmd. The serial_number is also
used in this decision, thus it's useful to know for debugging
purposes.
Reported-by: Peter M. Petrakis <peter.petrakis@canonical.com> Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Added missing release callback for file_operations mptctl_fops.
Without release callback there will be never freed. It remains on
mptctl's eent list even after the file is closed and released.
Relavent RHEL bugzilla is 660871
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If nfsd fails to find an exported via NFS file in the readahead cache, it
should increment corresponding nfsdstats counter (ra_depth[10]), but due to a
bug it may instead write to ra_depth[11], corrupting the following field.
In a kernel with NFSDv4 compiled in the corruption takes the form of an
increment of a counter of the number of NFSv4 operation 0's received; since
there is no operation 0, this is harmless.
In a kernel with NFSDv4 disabled it corrupts whatever happens to be in the
memory beyond nfsdstats.
Signed-off-by: Konstantin Khorenko <khorenko@openvz.org> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ben Hutchings [Mon, 7 Feb 2011 19:20:55 +0000 (19:20 +0000)]
bonding/vlan: Avoid mangled NAs on slaves without VLAN tag insertion
This is related to commit f88a4a9b65a6f3422b81be995535d0e69df11bb8
upstream, but the bug cannot be properly fixed without the other
changes to VLAN tagging in 2.6.37.
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Mike reports that since e9e9250b (sched: Scale down cpu_power due to RT
tasks), wake_affine() goes funny on RT tasks due to them still having a
!0 weight and wake_affine() still subtracts that from the rq weight.
Since nobody should be using se->weight for RT tasks, set the value to
zero. Also, since we now use ->cpu_power to normalize rq weights to
account for RT cpu usage, add that factor into the imbalance computation.
Reported-by: Mike Galbraith <efault@gmx.de> Tested-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1275316109.27810.22969.camel@twins> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[0.051203] CPU0: AMD QEMU Virtual CPU version 0.12.4 stepping 03
[0.052999] lockdep: fixing up alternatives.
[0.054105]
[0.054106] ===================================================
[0.054999] [ INFO: suspicious rcu_dereference_check() usage. ]
[0.054999] ---------------------------------------------------
[0.054999] kernel/sched.c:616 invoked rcu_dereference_check() without protection!
[0.054999]
[0.054999] other info that might help us debug this:
[0.054999]
[0.054999]
[0.054999] rcu_scheduler_active = 1, debug_locks = 1
[0.054999] 3 locks held by swapper/1:
[0.054999] #0: (cpu_add_remove_lock){+.+.+.}, at: [<ffffffff814be933>] cpu_up+0x42/0x6a
[0.054999] #1: (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff810400d8>] cpu_hotplug_begin+0x2a/0x51
[0.054999] #2: (&rq->lock){-.-...}, at: [<ffffffff814be2f7>] init_idle+0x2f/0x113
[0.054999]
[0.054999] stack backtrace:
[0.054999] Pid: 1, comm: swapper Not tainted 2.6.35 #1
[0.054999] Call Trace:
[0.054999] [<ffffffff81068054>] lockdep_rcu_dereference+0x9b/0xa3
[0.054999] [<ffffffff810325c3>] task_group+0x7b/0x8a
[0.054999] [<ffffffff810325e5>] set_task_rq+0x13/0x40
[0.054999] [<ffffffff814be39a>] init_idle+0xd2/0x113
[0.054999] [<ffffffff814be78a>] fork_idle+0xb8/0xc7
[0.054999] [<ffffffff81068717>] ? mark_held_locks+0x4d/0x6b
[0.054999] [<ffffffff814bcebd>] do_fork_idle+0x17/0x2b
[0.054999] [<ffffffff814bc89b>] native_cpu_up+0x1c1/0x724
[0.054999] [<ffffffff814bcea6>] ? do_fork_idle+0x0/0x2b
[0.054999] [<ffffffff814be876>] _cpu_up+0xac/0x127
[0.054999] [<ffffffff814be946>] cpu_up+0x55/0x6a
[0.054999] [<ffffffff81ab562a>] kernel_init+0xe1/0x1ff
[0.054999] [<ffffffff81003854>] kernel_thread_helper+0x4/0x10
[0.054999] [<ffffffff814c353c>] ? restore_args+0x0/0x30
[0.054999] [<ffffffff81ab5549>] ? kernel_init+0x0/0x1ff
[0.054999] [<ffffffff81003850>] ? kernel_thread_helper+0x0/0x10
[0.056074] Booting Node 0, Processors #1lockdep: fixing up alternatives.
[0.130045] #2lockdep: fixing up alternatives.
[0.203089] #3 Ok.
[0.275286] Brought up 4 CPUs
[0.276005] Total of 4 processors activated (16017.17 BogoMIPS).
The cgroup_subsys_state structures referenced by idle tasks are never
freed, because the idle tasks should be part of the root cgroup,
which is not removable.
The problem is that while we do in-fact hold rq->lock, the newly spawned
idle thread's cpu is not yet set to the correct cpu so the lockdep check
in task_group():
lockdep_is_held(&task_rq(p)->lock)
will fail.
But this is a chicken and egg problem. Setting the CPU's runqueue requires
that the CPU's runqueue already be set. ;-)
So insert an RCU read-side critical section to avoid the complaint.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Here a newly created task is having its runqueue assigned. The new task
is not yet on the tasklist, so cannot go away. This is therefore a false
positive, suppress with an RCU read-side critical section.
Reported-by: Ben Greear <greearb@candelatech.com Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Ben Greear <greearb@candelatech.com Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently sched_avg_update() (which updates rt_avg stats in the rq)
is getting called from scale_rt_power() (in the load balance context)
which doesn't take rq->lock.
Fix it by moving the sched_avg_update() to more appropriate
update_cpu_load() where the CFS load gets updated as well.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1282596171.2694.3.camel@sbsiddha-MOBL3> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When there's an xHCI host power loss after a suspend from memory, the USB
core attempts to reset and verify the USB devices that are attached to the
system. The xHCI driver has to reallocate those devices, since the
hardware lost all knowledge of them during the power loss.
When a hub is plugged in, and the host loses power, the xHCI hardware
structures are not updated to say the device is a hub. This is usually
done in hub_configure() when the USB hub is detected. That function is
skipped during a reset and verify by the USB core, since the core restores
the old configuration and alternate settings, and the hub driver has no
idea this happened. This bug makes the xHCI host controller reject the
enumeration of low speed devices under the resumed hub.
Therefore, make the USB core re-setup the internal xHCI hub device
information by calling update_hub_device() when hub_activate() is called
for a hub reset resume. After a host power loss, all devices under the
roothub get a reset-resume or a disconnect.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Clearing the cpu in prev's mm_cpumask early will avoid the flush tlb
IPI's while the cr3 is still pointing to the prev mm. And this window
can lead to the possibility of bogus TLB fills resulting in strange
failures. One such problematic scenario is mentioned below.
T1. CPU-1 is context switching from mm1 to mm2 context and got a NMI
etc between the point of clearing the cpu from the mm_cpumask(mm1)
and before reloading the cr3 with the new mm2.
T2. CPU-2 is tearing down a specific vma for mm1 and will proceed with
flushing the TLB for mm1. It doesn't send the flush TLB to CPU-1
as it doesn't see that cpu listed in the mm_cpumask(mm1).
T3. After the TLB flush is complete, CPU-2 goes ahead and frees the
page-table pages associated with the removed vma mapping.
T4. CPU-2 now allocates those freed page-table pages for something
else.
T5. As the CR3 and TLB caches for mm1 is still active on CPU-1, CPU-1
can potentially speculate and walk through the page-table caches
and can insert new TLB entries. As the page-table pages are
already freed and being used on CPU-2, this page walk can
potentially insert a bogus global TLB entry depending on the
(random) contents of the page that is being used on CPU-2.
T6. This bogus TLB entry being global will be active across future CR3
changes and can result in weird memory corruption etc.
To avoid this issue, for the prev mm that is handing over the cpu to
another mm, clear the cpu from the mm_cpumask(prev) after the cr3 is
changed.
Marking it for -stable, though we haven't seen any reported failure that
can be attributed to this.
Without tmpfs, shmem_readpage() is not compiled in causing an OOPS as
soon as we try to allocate some swappable pages for GEM.
Jan 19 22:52:26 harlie kernel: Modules linked in: i915(+) drm_kms_helper cfbcopyarea video backlight cfbimgblt cfbfillrect
Jan 19 22:52:26 harlie kernel:
Jan 19 22:52:26 harlie kernel: Pid: 1125, comm: modprobe Not tainted 2.6.37Harlie #10 To be filled by O.E.M./To be filled by O.E.M.
Jan 19 22:52:26 harlie kernel: EIP: 0060:[<00000000>] EFLAGS: 00010246 CPU: 3
Jan 19 22:52:26 harlie kernel: EIP is at 0x0
Jan 19 22:52:26 harlie kernel: EAX: 00000000 EBX: f7b7d000 ECX: f3383100 EDX: f7b7d000
Jan 19 22:52:26 harlie kernel: ESI: f1456118 EDI: 00000000 EBP: f2303c98 ESP: f2303c7c
Jan 19 22:52:26 harlie kernel: DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Jan 19 22:52:26 harlie kernel: Process modprobe (pid: 1125, ti=f2302000 task=f259cd80 task.ti=f2302000)
Jan 19 22:52:26 harlie kernel: Stack:
Jan 19 22:52:26 harlie udevd-work[1072]: '/sbin/modprobe -b pci:v00008086d00000046sv00000000sd00000000bc03sc00i00' unexpected exit with status 0x0009
Jan 19 22:52:26 harlie kernel: c1074061000000d0f2f42b8000000000000a13d2f2d5dcc000000001f2303cac
Jan 19 22:52:26 harlie kernel: c107416f00000000000a13d200000000f2303cd4f8d620edf2cee62000001000
Jan 19 22:52:26 harlie kernel: 00000000000a13d2f1456118f2d5dcc0f1a4000000001000f2303d04f8d637ab
Jan 19 22:52:26 harlie kernel: Call Trace:
Jan 19 22:52:26 harlie kernel: [<c1074061>] ? do_read_cache_page+0x71/0x160
Jan 19 22:52:26 harlie kernel: [<c107416f>] ? read_cache_page_gfp+0x1f/0x30
Jan 19 22:52:26 harlie kernel: [<f8d620ed>] ? i915_gem_object_get_pages+0xad/0x1d0 [i915]
Jan 19 22:52:26 harlie kernel: [<f8d637ab>] ? i915_gem_object_bind_to_gtt+0xeb/0x2d0 [i915]
Jan 19 22:52:26 harlie kernel: [<f8d65961>] ? i915_gem_object_pin+0x151/0x190 [i915]
Jan 19 22:52:26 harlie kernel: [<c11e16ed>] ? drm_gem_object_init+0x3d/0x60
Jan 19 22:52:26 harlie kernel: [<f8d65aa5>] ? i915_gem_init_ringbuffer+0x105/0x1e0 [i915]
Jan 19 22:52:26 harlie kernel: [<f8d571b7>] ? i915_driver_load+0x667/0x1160 [i915]
Reported-by: John J. Stimson-III <john@idsfa.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Knut Petersen <knut_petersen@t-online.de> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The accelerate mode bit gets checked by certain atom
command tables to set up some register state. It needs
to be clear when setting modes and set when not.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: 屋国遥 <hyagni@gmail.com> Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Multipath began to use blk_abort_queue() to allow for
lower latency path deactivation. This was found to
cause list corruption:
the cmd gets blk_abort_queued/timedout run on it and the scsi eh
somehow is able to complete and run scsi_queue_insert while
scsi_request_fn is still trying to process the request.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Cc: Mike Anderson <andmike@linux.vnet.ibm.com> Cc: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
No longer needlessly hold md->bdev->bd_inode->i_mutex when changing the
size of a DM device. This additional locking is unnecessary because
i_size_write() is already protected by the existing critical section in
dm_swap_table(). DM already has a reference on md->bdev so the
associated bd_inode may be changed without lifetime concerns.
A negative side-effect of having held md->bdev->bd_inode->i_mutex was
that a concurrent DM device resize and flush (via fsync) would deadlock.
Dropping md->bdev->bd_inode->i_mutex eliminates this potential for
deadlock. The following reproducer no longer deadlocks:
https://www.redhat.com/archives/dm-devel/2009-July/msg00284.html
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It is defined in include/linux/ieee80211.h. As per IEEE spec.
bit6 to bit15 in block ack parameter represents buffer size.
So the bitmask should be 0xFFC0.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
selinux_inode_init_security computes transitions sids even for filesystems
that use mount point labeling. It shouldn't do that. It should just use
the mount point label always and no matter what.
This causes 2 problems. 1) it makes file creation slower than it needs to be
since we calculate the transition sid and 2) it allows files to be created
with a different label than the mount point!
# id -Z
staff_u:sysadm_r:sysadm_t:s0-s0:c0.c1023
# sesearch --type --class file --source sysadm_t --target tmp_t
Found 1 semantic te rules:
type_transition sysadm_t tmp_t : file user_tmp_t;
# mount -o loop,context="system_u:object_r:tmp_t:s0" /tmp/fs /mnt/tmp
Whoops, we have a mount point labeled filesystem tmp_t with a user_tmp_t
labeled file!
Signed-off-by: Eric Paris <eparis@redhat.com> Reviewed-by: Reviewed-by: James Morris <jmorris@namei.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 2f90b865 added two new netlink message types to the netlink route
socket. SELinux has hooks to define if netlink messages are allowed to
be sent or received, but it did not know about these two new message
types. By default we allow such actions so noone likely noticed. This
patch adds the proper definitions and thus proper permissions
enforcement.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Roman Fietze <roman.fietze@telemotive.de> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Reported-and-tested-by: rbugz@biobind.com Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We atomically tested and cleared our bit in the cpumask, and yet the
number of cpus left (ie refs) was 0. How can this be?
It turns out commit 54fdade1c3332391948ec43530c02c4794a38172
("generic-ipi: make struct call_function_data lockless") is at fault. It
removes locking from smp_call_function_many and in doing so creates a
rather complicated race.
The problem comes about because:
- The smp_call_function_many interrupt handler walks call_function.queue
without any locking.
- We reuse a percpu data structure in smp_call_function_many.
- We do not wait for any RCU grace period before starting the next
smp_call_function_many.
Imagine a scenario where CPU A does two smp_call_functions back to back,
and CPU B does an smp_call_function in between. We concentrate on how CPU
C handles the calls:
CPU A CPU B CPU C CPU D
smp_call_function
smp_call_function_interrupt
walks
call_function.queue sees
data from CPU A on list
smp_call_function
smp_call_function_interrupt
walks
call_function.queue sees
(stale) CPU A on list
smp_call_function int
clears last ref on A
list_del_rcu, unlock
smp_call_function reuses
percpu *data A
data->cpumask sees and
clears bit in cpumask
might be using old or new fn!
decrements refs below 0
set data->refs (too late!)
The important thing to note is since the interrupt handler walks a
potentially stale call_function.queue without any locking, then another
cpu can view the percpu *data structure at any time, even when the owner
is in the process of initialising it.
The following test case hits the WARN_ON 100% of the time on my PowerPC
box (having 128 threads does help :)
#include <linux/module.h>
#include <linux/init.h>
#define ITERATIONS 100
static void do_nothing_ipi(void *dummy)
{
}
static void do_ipis(struct work_struct *dummy)
{
int i;
for (i = 0; i < ITERATIONS; i++)
smp_call_function(do_nothing_ipi, NULL, 1);
I tried to fix it by ordering the read and the write of ->cpumask and
->refs. In doing so I missed a critical case but Paul McKenney was able
to spot my bug thankfully :) To ensure we arent viewing previous
iterations the interrupt handler needs to read ->refs then ->cpumask then
->refs _again_.
Thanks to Milton Miller and Paul McKenney for helping to debug this issue.
[miltonm@bga.com: add WARN_ON and BUG_ON, remove extra read of refs before initial read of mask that doesn't help (also noted by Peter Zijlstra), adjust comments, hopefully clarify scenario ]
[miltonm@bga.com: remove excess tests] Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Milton Miller <miltonm@bga.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Remove the broken line wrapping handling in pdc_iodc_print().
It is broken in 3 ways :
- It doesn't keep track of the current screen position, it just
assumes that the new buffer will be printed at the begining of the
screen.
- It doesn't take in account that non printable characters won't
increase the current position on the screen.
- And last but not least, it triggers a kernel panic if a backspace
is the first char in the provided buffer :
Most terminals handle the line wrapping just fine. I've confirmed that
it works correctly on a C8000 with both vga and serial output.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Some of those functions try to adjust the CPU features, for example
to remove NAP support on some revisions. However, they seem to use
r5 as an index into the CPU table entry, which might have been right
a long time ago but no longer is. r4 is the right register to use.
This probably caused some off behaviours on some PowerMac variants
using 750cx or 7455 processor revisions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit c0e69a5bbc6f ("klist.c: bit 0 in pointer can't be used as flag")
intended to make sure that all klist objects were at least pointer size
aligned, but used the constant "4" which only works on 32-bit.
Use "sizeof(void *)" which is correct in all cases.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Added 0x0307 device id to support Motorola cables to the pl2303 usb
serial driver. This cable has a modified chip that is a pl2303, but
declares itself as 0307. Fixed by adding the right device id to the
supported devices list, assigning it the code labeled
PL2303_PRODUCT_ID_MOTOROLA.
Markus Kohn ran into a hard hang regression on an acer aspire
1310, when acpi is enabled. git bisect showed the following
commit as the bad one that introduced the boot regression.
x86, pat/mtrr: Rendezvous all the cpus for MTRR/PAT init
Because of the UP configuration of that platform,
native_smp_prepare_cpus() bailed out (in smp_sanity_check())
before doing the set_mtrr_aps_delayed_init()
Further down the boot path, native_smp_cpus_done() will call the
delayed MTRR initialization for the AP's (mtrr_aps_init()) with
mtrr_aps_delayed_init not set. This resulted in the boot
processor reprogramming its MTRR's to the values seen during the
start of the OS boot. While this is not needed ideally, this
shouldn't have caused any side-effects. This is because the
reprogramming of MTRR's (set_mtrr_state() that gets called via
set_mtrr()) will check if the live register contents are
different from what is being asked to write and will do the actual
write only if they are different.
BP's mtrr state is read during the start of the OS boot and
typically nothing would have changed when we ask to reprogram it
on BP again because of the above scenario on an UP platform. So
on a normal UP platform no reprogramming of BP MTRR MSR's
happens and all is well.
However, on this platform, bios seems to be modifying the fixed
mtrr range registers between the start of OS boot and when we
double check the live registers for reprogramming BP MTRR
registers. And as the live registers are modified, we end up
reprogramming the MTRR's to the state seen during the start of
the OS boot.
During ACPI initialization, something in the bios (probably smi
handler?) don't like this fact and results in a hard lockup.
We didn't see this boot hang issue on this platform before the
commit d0af9eed5aa91b6b7b5049cae69e5ea956fd85c3, because only
the AP's (if any) will program its MTRR's to the value that BP
had at the start of the OS boot.
Fix this issue by checking mtrr_aps_delayed_init before
continuing further in the mtrr_aps_init(). Now, only AP's (if
any) will program its MTRR's to the BP values during boot.
[ By the way, this behavior of the bios modifying MTRR's after the start
of the OS boot is not common and the kernel is not prepared to
handle this situation well. Irrespective of this issue, during
suspend/resume, linux kernel will try to reprogram the BP's MTRR values
to the values seen during the start of the OS boot. So suspend/resume might
be already broken on this platform for all linux kernel versions. ]
Reported-and-bisected-by: Markus Kohn <jabber@gmx.org> Tested-by: Markus Kohn <jabber@gmx.org> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Thomas Renninger <trenn@novell.com> Cc: Rafael Wysocki <rjw@novell.com> Cc: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <1296694975.4418.402.camel@sbsiddha-MOBL3.sc.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The wake_up_process() call in ptrace_detach() is spurious and not
interlocked with the tracee state. IOW, the tracee could be running or
sleeping in any place in the kernel by the time wake_up_process() is
called. This can lead to the tracee waking up unexpectedly which can be
dangerous.
The wake_up is spurious and should be removed but for now reduce its
toxicity by only waking up if the tracee is in TRACED or STOPPED state.
This bug can possibly be used as an attack vector. I don't think it
will take too much effort to come up with an attack which triggers oops
somewhere. Most sleeps are wrapped in condition test loops and should
be safe but we have quite a number of places where sleep and wakeup
conditions are expected to be interlocked. Although the window of
opportunity is tiny, ptrace can be used by non-privileged users and with
some loading the window can definitely be extended and exploited.
Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A check against division by zero was modified in commit b0525b48.
Since this change time_to_empty_now is always reported as zero
while the battery is discharging and as a negative value while
the battery is charging. This is because current is negative while
the battery is discharging.
Fix the check introduced by commit b0525b48 so that time_to_empty_now
is reported correctly during discharge and as zero while charging.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Acked-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We sometimes need to map between the virtio device and
the given pci device. One such use is OS installer that
gets the boot pci device from BIOS and needs to
find the relevant block device. Since it can't,
installation fails.
Instead of creating a top-level devices/virtio-pci
directory, create each device under the corresponding
pci device node. Symlinks to all virtio-pci
devices can be found under the pci driver link in
bus/pci/drivers/virtio-pci/devices, and all virtio
devices under drivers/bus/virtio/devices.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Gleb Natapov <gleb@redhat.com> Tested-by: "Daniel P. Berrange" <berrange@redhat.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
pci-stub uses strsep() to separate list of ids and generates a warning
message when it fails to parse an id. However, not specifying the
parameter results in ids set to an empty string. strsep() happily
returns the empty string as the first token and thus triggers the
warning message spuriously.
Make the tokner ignore zero length ids.
Reported-by: Chris Wright <chrisw@sous-sol.org> Reported-by: Prasad Joshi <P.G.Joshi@student.reading.ac.uk> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In fsl_rio_dbell_handler() the code currently simply acknowledges the QFI
queue full interrupt, but does nothing to resolve the queue full
condition. Instead, it jumps to the end of the isr. When a queue full
condition occurs, the isr is then re-entered immediately and continually,
forever.
The fix is to just fall through and read out current doorbell entries.
Signed-off-by: Thomas Taranowski <tom@baringforge.com> Cc: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Li Yang <leoli@freescale.com> Cc: Thomas Moll <thomas.moll@sysgo.com> Cc: Micha Nelissen <micha@neli.hopto.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
rtc-cmos was setting suspend/resume hooks at the device_driver level.
However, the platform bus code (drivers/base/platform.c) only looks for
resume hooks at the dev_pm_ops level, or within the platform_driver.
Switch rtc_cmos to use dev_pm_ops so that suspend/resume code is executed
again.
Paul said:
: The user visible symptom in our (XO laptop) case was that rtcwake would
: fail to wake the laptop. The RTC alarm would expire, but the wakeup
: wasn't unmasked.
:
: As for severity, the impact may have been reduced because if I recall
: correctly, the bug only affected platforms with CONFIG_PNP disabled.
Signed-off-by: Paul Fox <pgf@laptop.org> Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to tweak how we query the active capture/playback state after
the recent overhauls of common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Conexant codec driver adds the jack arrays in init callback which
may be called also in each PM resume. This results in the addition of
new jack element at each time.
The fix is to check whether the requested jack is already present in
the array.