Dan Carpenter [Thu, 15 Dec 2011 11:31:37 +0000 (14:31 +0300)]
usb: renesas_usbhs: silence a gcc warning
Gcc complains about this printk:
drivers/usb/renesas_usbhs/mod_gadget.c:188:3: warning: format ‘%x’
expects argument of type ‘unsigned int’, but argument 3 has type
‘dma_addr_t’ [-Wformat]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: renesas_usbhs: disable attch irq after device attached
attch interrupt might happen infinitely on some USB hub (self power?).
This patch disable attch irq after device attached,
and enable it again when detach irq happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
This patch adds usbhsh_pipe_attach/detach() functions for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Current renesas_usbhs had been assigning udev to each urb.
It was executed even though it was device0.
For this reason, the device0 had to set the new device address
which has still not been assigned. (it will be assigned on next step).
Current renesas_usbhs used fixed address for it.
but it is not good for USB hub support.
This patch modifies this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Neil Zhang [Wed, 30 Nov 2011 01:57:16 +0000 (09:57 +0800)]
usb: gadget: mv_udc: refine suspend/resume function
This patch impletments system suspend/resume functions for Marvell
otg controller.
If OTG is enabled, OTG driver will do most of the work.
If not, we will check clock gating.
If clock gating is enabled, the UDC will be start/stop automatically.
If not, UDC will be start/stop in suspend/resume functions.
Signed-off-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Thomas Meyer [Tue, 29 Nov 2011 21:08:00 +0000 (22:08 +0100)]
usb: gadget: Use kcalloc instead of kzalloc to allocate array
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Acked-by: Michal Nazarewicz <[4]mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: renesas_usbhs: send packet in necessary timing.
Current renesas_usbhs driver always tries to send packet in end of recip handler.
But it breaks chapter 9 EndpointHalt test.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: rename usb_gadget_driver::speed to max_speed
This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”. This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.
This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures. All
of those represent the *maximal* speed given entity supports.
After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
supports, and
* usb_composite_driver::max_speed - maximal speed composite
gadget supports.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: renesas_usbhs: parameter cleanup for usbhsh_device_xx()
current mod_host used usbhs_device_alloc/free(),
but allocated variable was attached to each xx->hcpriv.
The intuitively clear name was not xxx_alloc/free() but xxx_attach/detach().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: renesas_usbhs: parameter cleanup for usbhsh_endpoint_xx()
current mod_host used usbhs_endpoint_alloc/free(),
but allocated variable was attached to each xx->hcpriv.
The intuitively clear name was not xxx_alloc/free() but xxx_attach/detach().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: renesas_usbhs: check device0 status when alloc
device0 was treated without checking in usbhsh_device_alloc().
but "udev->usbv" and "dev_set_drvdata()" will be overwritten
if device0 was multi-allocated.
This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
DCP data/status stage needs ureq to usbhs_pkt_push(),
but sometimes, there is no data stage.
In that case, allocated ureq was not freed,
Current ureq alloc/free pair were difficult to understand.
This patch removed unnecessary/un-understandable ureq alloc
from usbhsh_urb_enqueue(), and create simpler alloc/free pair.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Yuping Luo [Wed, 26 Oct 2011 02:13:10 +0000 (19:13 -0700)]
usb: gadget: mass_storage: support multi-luns with different logic block size
With Peiyu's patch "gadget: mass_storage: adapt logic block size to bound block
devices" (http://www.spinics.net/lists/linux-usb/msg50791.html), now mass storage
can adjust logic block size dynamically based on real devices.
Then there is one issue caused by it, if two luns have different logic block size,
mass storage can't work.
Let's check the current software flow:
1. get_next_command(): call received_cbw();
2. received_cbw(): update common->lun = cbw->Lun, but common->curlen is not updated;
3. do_scsi_command(): in READ_X and WRITE_X commands, common->data_size_from_cmnd is
updated by common->curlun->blkbits;
4. check_command(): update common->curlun according to common->lun
As you can see, the step 3 uses wrong common->curlun, then wrong common->curlun->blkbits.
If the two luns have same blkbits, there isn't issue. Otherwise, both will fail.
This patch moves the common->curlun update to step 1, then make sure step 3 gets right
blkbits and data_size_from_cmnd.
Cc: Peiyu Li <peiyu.li@csr.com> Signed-off-by: YuPing Luo <yuping.luo@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
USB: ci13xxx_udc: handle controllers with less than 16 EPs
The ci13xxx_udc driver checks the number of endpoints in the udc
controller, however some routines expect that the hardware has 16
bidirectional endpoints.
This patch improves the driver to work on controllers with less than
16 endpoints like the udc controller found on freescale's
mx23 and mx28.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
USB: ci13xxx_udc: make suspend and resume in gadget driver optional
Some gadget drivers don't implement suspend and/or resume functions.
Instead of changing the gadget drivers, make suspend and resume in
ci13xxx_udc (following other udc drivers) optional.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Torvalds [Fri, 9 Dec 2011 22:45:44 +0000 (14:45 -0800)]
Merge git://git.samba.org/sfrench/cifs-2.6
* git://git.samba.org/sfrench/cifs-2.6:
cifs: check for NULL last_entry before calling cifs_save_resume_key
cifs: attempt to freeze while looping on a receive attempt
cifs: Fix sparse warning when calling cifs_strtoUCS
CIFS: Add descriptions to the brlock cache functions
Linus Torvalds [Fri, 9 Dec 2011 22:45:12 +0000 (14:45 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Calling __pa() with an ioremap()ed address is invalid
x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
x86/intel_mid: Kconfig select fix
x86/intel_mid: Fix the Kconfig for MID selection
Linus Torvalds [Fri, 9 Dec 2011 22:41:50 +0000 (14:41 -0800)]
Merge branch 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6
* 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6:
spi/gpio: fix section mismatch warning
spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m build
spi/nuc900: Include linux/module.h
spi/ath79: fix compile error due to missing include
Linus Torvalds [Fri, 9 Dec 2011 16:18:08 +0000 (08:18 -0800)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: raid5 crash during degradation
md/raid5: never wait for bad-block acks on failed device.
md: ensure new badblocks are handled promptly.
md: bad blocks shouldn't cause a Blocked status on a Faulty device.
md: take a reference to mddev during sysfs access.
md: refine interpretation of "hold_active == UNTIL_IOCTL".
md/lock: ensure updates to page_attrs are properly locked.
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: use new generic {enable,disable}_percpu_irq() routines
drivers/net/ethernet/tile: use skb_frag_page() API
asm-generic/unistd.h: support new process_vm_{readv,write} syscalls
arch/tile: fix double-free bug in homecache_free_pages()
arch/tile: add a few #includes and an EXPORT to catch up with kernel changes.
Linus Torvalds [Fri, 9 Dec 2011 16:07:42 +0000 (08:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix lost speaker volume controls
ALSA: hda/realtek - Create "Bass Speaker" for two speaker pins
ALSA: hda/realtek - Don't create extra controls with channel suffix
ALSA: hda - Fix remaining VREF mute-LED NID check in post-3.1 changes
ALSA: hda - Fix GPIO LED setup for IDT 92HD75 codecs
ASoC: Provide a more complete DMA driver stub
ASoC: Remove references to corgi and spitz from machine driver document
ASoC: Make SND_SOC_MX27VIS_AIC32X4 depend on I2C
ASoC: Fix dependency for SND_SOC_RAUMFELD and SND_PXA2XX_SOC_HX4700
ASoC: uda1380: Return proper error in uda1380_modinit failure path
ASoC: kirkwood: Make SND_KIRKWOOD_SOC_OPENRD and SND_KIRKWOOD_SOC_T5325 depend on I2C
ASoC: Mark WM8994 ADC muxes as virtual
ALSA: hda/realtek - Fix Oops in alc_mux_select()
ALSA: sis7019 - give slow codecs more time to reset
Linus Torvalds [Fri, 9 Dec 2011 16:07:24 +0000 (08:07 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Do no try to schedule task events if there are none
lockdep, kmemcheck: Annotate ->lock in lockdep_init_map()
perf header: Use event_name() to get an event name
perf stat: Failure with "Operation not supported"
Modify initialization of PCIe capability registers in Tsi721 mport driver:
- change Completion Timeout value to avoid unexpected data transfer
aborts during intensive traffic.
- replace hardcoded offset of PCIe capability block by making it use the
common function.
This patch is applicable to kernel versions starting from 3.2-rc1.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug fix for Tsi721 RapidIO mport driver: Tsi721 supports four RapidIO
mailboxes (MBOX0 - MBOX3) as defined by RapidIO specification. Mailbox
resources has to be properly reported to allow use of all available
mailboxes (initial version reports only MBOX0).
This patch is applicable to kernel versions staring from 3.2-rc1.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 8 Dec 2011 22:34:32 +0000 (14:34 -0800)]
procfs: do not overflow get_{idle,iowait}_time for nohz
Since commit a25cac5198d4 ("proc: Consider NO_HZ when printing idle and
iowait times") we are reporting idle/io_wait time also while a CPU is
tickless. We rely on get_{idle,iowait}_time functions to retrieve
proper data.
These functions, however, use usecs_to_cputime to translate micro
seconds time to cputime64_t. This is just an alias to usecs_to_jiffies
which reduces the data type from u64 to unsigned int and also checks
whether the given parameter overflows jiffies_to_usecs(MAX_JIFFY_OFFSET)
and returns MAX_JIFFY_OFFSET in that case.
When we overflow depends on CONFIG_HZ but especially for CONFIG_HZ_300
it is quite low (1431649781) so we are getting MAX_JIFFY_OFFSET for
>3000s! until we overflow unsigned int. Just for reference
CONFIG_HZ_100 has an overflow window around 20s, CONFIG_HZ_250 ~8s and
CONFIG_HZ_1000 ~2s.
This results in a bug when people saw [h]top going mad reporting 100%
CPU usage even though there was basically no CPU load. The reason was
simply that /proc/stat stopped reporting idle/io_wait changes (and
reported MAX_JIFFY_OFFSET) and so the only change happening was for user
system time.
Let's use nsecs_to_jiffies64 instead which doesn't reduce the precision
to 32b type and it is much more appropriate for cumulative time values
(unlike usecs_to_jiffies which intended for timeout calculations).
Signed-off-by: Michal Hocko <mhocko@suse.cz> Tested-by: Artem S. Tashkinov <t.artem@mailcity.com> Cc: Dave Jones <davej@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 8 Dec 2011 22:34:30 +0000 (14:34 -0800)]
mm: vmalloc: check for page allocation failure before vmlist insertion
Commit f5252e00 ("mm: avoid null pointer access in vm_struct via
/proc/vmallocinfo") adds newly allocated vm_structs to the vmlist after
it is fully initialised. Unfortunately, it did not check that
__vmalloc_area_node() successfully populated the area. In the event of
allocation failure, the vmalloc area is freed but the pointer to freed
memory is inserted into the vmlist leading to a a crash later in
get_vmalloc_info().
This patch adds a check for ____vmalloc_area_node() failure within
__vmalloc_node_range. It does not use "goto fail" as in the previous
error path as a warning was already displayed by __vmalloc_area_node()
before it called vfree in its failure path.
Credit goes to Luciano Chavez for doing all the real work of identifying
exactly where the problem was.
Michal Hocko [Thu, 8 Dec 2011 22:34:27 +0000 (14:34 -0800)]
mm: Ensure that pfn_valid() is called once per pageblock when reserving pageblocks
setup_zone_migrate_reserve() expects that zone->start_pfn starts at
pageblock_nr_pages aligned pfn otherwise we could access beyond an
existing memblock resulting in the following panic if
CONFIG_HOLES_IN_ZONE is not configured and we do not check pfn_valid:
We crashed in pageblock_is_reserved() when accessing pfn 0xc0000 because
highstart_pfn = 0x36ffe.
The issue was introduced in 3.0-rc1 by 6d3163ce ("mm: check if any page
in a pageblock is reserved before marking it MIGRATE_RESERVE").
Make sure that start_pfn is always aligned to pageblock_nr_pages to
ensure that pfn_valid s always called at the start of each pageblock.
Architectures with holes in pageblocks will be correctly handled by
pfn_valid_within in pageblock_is_reserved.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Mel Gorman <mgorman@suse.de> Tested-by: Dang Bo <bdang@vmware.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Arve Hjnnevg <arve@android.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> [3.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Youquan Song [Thu, 8 Dec 2011 22:34:18 +0000 (14:34 -0800)]
thp: set compound tail page _count to zero
Commit 70b50f94f1644 ("mm: thp: tail page refcounting fix") keeps all
page_tail->_count zero at all times. But the current kernel does not
set page_tail->_count to zero if a 1GB page is utilized. So when an
IOMMU 1GB page is used by KVM, it wil result in a kernel oops because a
tail page's _count does not equal zero.
Youquan Song [Thu, 8 Dec 2011 22:34:16 +0000 (14:34 -0800)]
thp: add compound tail page _mapcount when mapped
With the 3.2-rc kernel, IOMMU 2M pages in KVM works. But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.
The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd. If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.
So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.
This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.
Peter Zijlstra [Thu, 8 Dec 2011 22:34:13 +0000 (14:34 -0800)]
printk: avoid double lock acquire
Commit 4f2a8d3cf5e ("printk: Fix console_sem vs logbuf_lock unlock race")
introduced another silly bug where we would want to acquire an already
held lock. Avoid this.
Reported-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More players joined to memory cgroup developments and Johannes' great work
changed internal design of memory cgroup dramatically. And he will do
more works. Michal Hokko did many bug fixes and know memory cgroup very
well. Daisuke Nishimura helped us very much but he seems busy now.
Thanks to his works.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: Michal Hocko <mhocko@suse.cz> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Cc: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
khugepaged can sometimes cause suspend to fail, requiring that the user
retry the suspend operation.
Use wait_event_freezable_timeout() instead of
schedule_timeout_interruptible() to avoid missing freezer wakeups. A
try_to_freeze() would have been needed in the khugepaged_alloc_hugepage
tight loop too in case of the allocation failing repeatedly, and
wait_event_freezable_timeout will provide it too.
khugepaged would still freeze just fine by trying again the next minute
but it's better if it freezes immediately.
Reported-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Tested-by: Jiri Slaby <jslaby@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com> Cc: "Rafael J. Wysocki" <rjw@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A shrinker function can return -1, means that it cannot do anything
without a risk of deadlock. For example prune_super() does this if it
cannot grab a superblock refrence, even if nr_to_scan=0. Currently we
interpret this -1 as a ULONG_MAX size shrinker and evaluate `total_scan'
according to this. So the next time around this shrinker can cause
really big pressure. Let's skip such shrinkers instead.
Also make total_scan signed, otherwise the check (total_scan < 0) below
never works.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Dave Chinner <david@fromorbit.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matt Fleming [Fri, 18 Nov 2011 13:09:11 +0000 (13:09 +0000)]
x86, efi: Calling __pa() with an ioremap()ed address is invalid
If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.
On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:
BUG: unable to handle kernel paging request at f7f22280
IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
[...]
A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().
Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,
Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Matthew Garrett <mjg@redhat.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Huang Ying <huang.ying.caritas@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jeff Layton [Fri, 2 Dec 2011 01:23:34 +0000 (20:23 -0500)]
cifs: check for NULL last_entry before calling cifs_save_resume_key
Prior to commit eaf35b1, cifs_save_resume_key had some NULL pointer
checks at the top. It turns out that at least one of those NULL
pointer checks is needed after all.
When the LastNameOffset in a FIND reply appears to be beyond the end of
the buffer, CIFSFindFirst and CIFSFindNext will set srch_inf.last_entry
to NULL. Since eaf35b1, the code will now oops in this situation.
Fix this by having the callers check for a NULL last entry pointer
before calling cifs_save_resume_key. No change is needed for the
call site in cifs_readdir as it's not reachable with a NULL
current_entry pointer.
Cc: stable@vger.kernel.org Cc: Christoph Hellwig <hch@infradead.org> Reported-by: Adam G. Metzler <adamgmetzler@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
Jeff Layton [Fri, 2 Dec 2011 01:22:41 +0000 (20:22 -0500)]
cifs: attempt to freeze while looping on a receive attempt
In the recent overhaul of the demultiplex thread receive path, I
neglected to ensure that we attempt to freeze on each pass through the
receive loop.
Reported-and-Tested-by: Woody Suwalski <terraluna977@gmail.com> Reported-and-Tested-by: Adam Williamson <awilliam@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
Linus Torvalds [Thu, 8 Dec 2011 21:18:59 +0000 (13:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: drop spin lock when memory alloc fails
Btrfs: check if the to-be-added device is writable
Btrfs: try cluster but don't advance in search list
Btrfs: try to allocate from cluster even at LOOP_NO_EMPTY_SIZE
Tetsuo Handa [Thu, 8 Dec 2011 12:24:06 +0000 (21:24 +0900)]
TOMOYO: Fix pathname handling of disconnected paths.
Current tomoyo_realpath_from_path() implementation returns strange pathname
when calculating pathname of a file which belongs to lazy unmounted tree.
Use local pathname rather than strange absolute pathname in that case.
Also, this patch fixes a regression by commit 02125a82 "fix apparmor
dereferencing potentially freed dentry, sanitize __d_path() API".
Mark Langsdorf [Fri, 18 Nov 2011 15:33:06 +0000 (16:33 +0100)]
x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.
On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.
This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.com Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org
Li Zefan [Thu, 8 Dec 2011 01:08:40 +0000 (20:08 -0500)]
Btrfs: check if the to-be-added device is writable
If we call ioctl(BTRFS_IOC_ADD_DEV) directly, we'll succeed in adding
a readonly device to a btrfs filesystem, and btrfs will write to
that device, emitting kernel errors:
[ 3109.833692] lost page write due to I/O error on loop2
[ 3109.833720] lost page write due to I/O error on loop2
...
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Thu, 8 Dec 2011 01:08:40 +0000 (20:08 -0500)]
Btrfs: try cluster but don't advance in search list
When we find an existing cluster, we switch to its block group as the
current block group, possibly skipping multiple blocks in the process.
Furthermore, under heavy contention, multiple threads may fail to
allocate from a cluster and then release just-created clusters just to
proceed to create new ones in a different block group.
This patch tries to allocate from an existing cluster regardless of its
block group, and doesn't switch to that group, instead proceeding to
try to allocate a cluster from the group it was iterating before the
attempt.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
NeilBrown [Thu, 8 Dec 2011 05:26:08 +0000 (16:26 +1100)]
md: ensure new badblocks are handled promptly.
When we mark blocks as bad we need them to be acknowledged by the
metadata handler promptly.
For an in-kernel metadata handler that was already being done. But
for an external metadata handler we need to alert it of the change by
sending a notification through the sysfs file. This adds that
notification.
NeilBrown [Thu, 8 Dec 2011 05:22:48 +0000 (16:22 +1100)]
md: bad blocks shouldn't cause a Blocked status on a Faulty device.
Once a device is marked Faulty the badblocks - whether acknowledged or
not - become irrelevant. So they shouldn't cause the device to be
marked as Blocked.
Without this patch, a process might write "-blocked" to clear the
Blocked status, but while that will correctly fail the device, it
won't remove the apparent 'blocked' status.
NeilBrown [Thu, 8 Dec 2011 04:49:46 +0000 (15:49 +1100)]
md: take a reference to mddev during sysfs access.
When we are accessing an mddev via sysfs we know that the
mddev cannot disappear because it has an embedded kobj which
is refcounted by sysfs.
And we also take the mddev_lock.
However this is not enough.
The final mddev_put could have been called and the
mddev_delayed_delete is waiting for sysfs to let go so it can destroy
the kobj and mddev.
In this state there are a lot of changes that should not be attempted.
To to guard against this we:
- initialise mddev->all_mddevs in on last put so the state can be
easily detected.
- in md_attr_show and md_attr_store, check ->all_mddevs under
all_mddevs_lock and mddev_get the mddev if it still appears to
be active.
This means that if we get to sysfs as the mddev is being deleted we
will get -EBUSY.
rdev_attr_store and rdev_attr_show are similar but already have
sufficient protection. They check that rdev->mddev still points to
mddev after taking mddev_lock. As this is cleared before delayed
removal which can only be requested under the mddev_lock, this
ensure the rdev and mddev are still alive.
projects / linux-beck.git / log