Saeed Mahameed [Sun, 28 Aug 2016 22:13:44 +0000 (01:13 +0300)]
net/mlx5e: Don't post fragmented MPWQE when RQ is disabled
ICO (Internal control operations) SQ (Send Queue) is closed/disabled
after RQ (Receive Queue). After RQ is closed an ICO SQ completion
might post a fragmented MPWQE (Multi Packet Work Queue Element) into
that RQ.
As on regular RQ post, check if we are allowed to post to that
RQ (RQ is enabled). Cleanup in-progress UMR MPWQE on mlx5e_free_rx_descs
if needed.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:43 +0000 (01:13 +0300)]
net/mlx5e: Don't wait for RQ completions on close
This will significantly reduce receive queue flush time on interface
down.
Instead of asking the firmware to flush the RQ (Receive Queue) via
asynchronous completions when moved to error, we handle RQ flush
manually (mlx5e_free_rx_descs) same as we did when RQ flush got timed
out.
This will reduce RQs flush time and speedup interface down procedure
(ifconfig down) from 6 sec to 0.3 sec on a 48 cores system.
Moved mlx5e_free_rx_descs en_main.c where it is needed, to keep en_rx.c
free form non critical data path code for better code locality.
Fixes: 6cd392a082de ('net/mlx5e: Handle RQ flush in error cases') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 28 Aug 2016 22:13:42 +0000 (01:13 +0300)]
net/mlx5e: Limit UMR length to the device's limitation
ConnectX-4 UMR (User Memory Region) MTT translation table offset in WQE
is limited to U16_MAX, before this patch we ignored that limitation and
requested the maximum possible UMR translation length that the netdev
might need (MAX channels * MAX pages per channel).
In case of a system with #cores > 32 and when linear WQE allocation fails,
falling back to using UMR WQEs will cause the RQ (Receive Queue) to get
stuck.
Here we limit UMR length to min(U16_MAX, max required pages) (while
considering the required alignments) on driver load, by default U16_MAX is
sufficient since the default RX rings value guarantees that we are in
range, dynamically (on set_ringparam/set_channels) we will check if the
new required UMR length (num mtts) is still in range, if not, fail the
request.
Fixes: bc77b240b3c5 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 26 Aug 2016 15:51:39 +0000 (08:51 -0700)]
rhashtable: fix a memory leak in alloc_bucket_locks()
If vmalloc() was successful, do not attempt a kmalloc_array()
Fixes: 4cf0b354d92e ("rhashtable: avoid large lock-array allocations") Reported-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: CAI Qian <caiqian@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Fri, 26 Aug 2016 10:19:34 +0000 (11:19 +0100)]
sfc: fix potential stack corruption from running past stat bitmask
On 32-bit systems, mask is only an array of 3 longs, not 4, so don't try
to write to mask[3].
Also include build-time checks in case the size of the bitmask changes.
Fixes: 3c36a2aded8c ("sfc: display vadaptor statistics for all interfaces") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 25 Aug 2016 16:30:52 +0000 (18:30 +0200)]
team: loadbalance: push lacpdus to exact delivery
When team is in bridge and LACP is utilized, LACPDU packets are pushed
to userspace using raw socket and there they are processed. However,
since 8626c56c8279b, LACPDU skbs are dropped by bridge rx_handler so
they never reach packet handlers in rx path. Fix this by explicity treat
LACPDUs to be pushed to exact delivery in team rx_handler.
Reported-by: Ido Schimmel <idosch@mellanox.com> Fixes: 8626c56c8279b ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 25 Aug 2016 06:51:10 +0000 (07:51 +0100)]
net: hns: dereference ppe_cb->ppe_common_cb if it is non-null
ppe_cb->ppe_common_cb is being dereferenced before a null check is
being made on it. If ppe_cb->ppe_common_cb is null then we end up
with a null pointer dereference when assigning dsaf_dev. Fix this
by moving the initialisation of dsaf_dev once we know
ppe_cb->ppe_common_cb is OK to dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Thu, 25 Aug 2016 01:45:39 +0000 (09:45 +0800)]
8139cp: Fix one possible deadloop in cp_rx_poll
When cp_rx_poll does not get enough packet, it will check the rx
interrupt status again. If so, it will jumpt to rx_status_loop again.
But the goto jump resets the rx variable as zero too.
As a result, it causes one possible deadloop. Assume this case,
rx_status_loop only gets the packet count which is less than budget,
and (cpr16(IntrStatus) & cp_rx_intr_mask) condition is always true.
It causes the deadloop happens and system is blocked.
Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.
Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xander Huff [Wed, 24 Aug 2016 21:47:53 +0000 (16:47 -0500)]
Revert "phy: IRQ cannot be shared"
This reverts:
commit 33c133cc7598 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 24 Aug 2016 18:01:20 +0000 (11:01 -0700)]
net: dsa: bcm_sf2: Fix race condition while unmasking interrupts
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Aug 2016 16:39:02 +0000 (09:39 -0700)]
qdisc: fix a module refcount leak in qdisc_create_dflt()
Should qdisc_alloc() fail, we must release the module refcount
we got right before.
Fixes: 6da7c8fcbcbd ("qdisc: allow setting default queuing discipline") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 24 Aug 2016 13:32:19 +0000 (13:32 +0000)]
tipc: fix the error handling in tipc_udp_enable()
Fix to return a negative error code in enable_mcast() error handling
case, and release udp socket when necessary.
Fixes: d0f91938bede ("tipc: add ip/udp media type") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: Fix bt_sock_recvmsg when MSG_TRUNC is not set
Commit b5f34f9420b50c9b5876b9a2b68e96be6d629054 attempt to introduce
proper handling for MSG_TRUNC but recv and variants should still work
as read if no flag is passed, but because the code may set MSG_TRUNC to
msg->msg_flags that shall not be used as it may cause it to be behave as
if MSG_TRUNC is always, so instead of using it this changes the code to
use the flags parameter which shall contain the original flags.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Yotam Gigi [Wed, 24 Aug 2016 09:18:52 +0000 (11:18 +0200)]
mlxsw: router: Enable neighbors to be created on stacked devices
Make the function mlxsw_router_neigh_construct search the rif according
to the neighbour dev other than the dev that was passed to the ndo, thus
allowing creating neigbhours upon stacked devices.
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table") Signed-off-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 24 Aug 2016 09:18:51 +0000 (11:18 +0200)]
mlxsw: spectrum: Add missing flood to router port
In case we have a layer 3 interface on top of a bridge (VLAN / FID RIF),
then we should flood the following packet types to the router:
* Broadcast: If DIP is the broadcast address of the interface, then we
need to be able to get it to CPU by trapping it following route lookup.
* Reserved IP multicast (224.0.0.X): Some control packets (e.g. OSPF)
use this range and are trapped in the router block.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 27 Jul 2016 18:40:14 +0000 (11:40 -0700)]
Bluetooth: split sk_filter in l2cap_sock_recv_cb
During an audit for sk_filter(), we found that rx_busy_skb handling
in l2cap_sock_recv_cb() and l2cap_sock_recvmsg() looks not quite as
intended.
The assumption from commit e328140fdacb ("Bluetooth: Use event-driven
approach for handling ERTM receive buffer") is that errors returned
from sock_queue_rcv_skb() are due to receive buffer shortage. However,
nothing should prevent doing a setsockopt() with SO_ATTACH_FILTER on
the socket, that could drop some of the incoming skbs when handled in
sock_queue_rcv_skb().
In that case sock_queue_rcv_skb() will return with -EPERM, propagated
from sk_filter() and if in L2CAP_MODE_ERTM mode, wrong assumption was
that we failed due to receive buffer being full. From that point onwards,
due to the to-be-dropped skb being held in rx_busy_skb, we cannot make
any forward progress as rx_busy_skb is never cleared from l2cap_sock_recvmsg(),
due to the filter drop verdict over and over coming from sk_filter().
Meanwhile, in l2cap_sock_recv_cb() all new incoming skbs are being
dropped due to rx_busy_skb being occupied.
Instead, just use __sock_queue_rcv_skb() where an error really tells that
there's a receive buffer issue. Split the sk_filter() and enable it for
non-segmented modes at queuing time since at this point in time the skb has
already been through the ERTM state machine and it has been acked, so dropping
is not allowed. Instead, for ERTM and streaming mode, call sk_filter() in
l2cap_data_rcv() so the packet can be dropped before the state machine sees it.
Fixes: e328140fdacb ("Bluetooth: Use event-driven approach for handling ERTM receive buffer") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Frederic Dalleau [Tue, 23 Aug 2016 05:59:19 +0000 (07:59 +0200)]
Bluetooth: Fix memory leak at end of hci requests
In hci_req_sync_complete the event skb is referenced in hdev->req_skb.
It is used (via hci_req_run_skb) from either __hci_cmd_sync_ev which will
pass the skb to the caller, or __hci_req_sync which leaks.
David Ahern [Wed, 24 Aug 2016 04:05:27 +0000 (21:05 -0700)]
net: diag: Fix refcnt leak in error path destroying socket
inet_diag_find_one_icsk takes a reference to a socket that is not
released if sock_diag_destroy returns an error. Fix by changing
tcp_diag_destroy to manage the refcnt for all cases and remove
the sock_put calls from tcp_abort.
Fixes: c1e64e298b8ca ("net: diag: Support destroying TCP sockets") Reported-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda297729171 (tun: Support software transmit time stamping.) Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Francis Yan <francisyyan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Tue, 23 Aug 2016 15:40:52 +0000 (11:40 -0400)]
sctp: fix overrun in sctp_diag_dump_one()
The function sctp_diag_dump_one() currently performs a memcpy()
of 64 bytes from a 16 byte field into another 16 byte field. Fix
by using correct size, use sizeof to obtain correct size instead
of using a hard-coded constant.
Fixes: 8f840e47f190 ("sctp: add the sctp_diag.c file") Signed-off-by: Lance Richardson <lrichard@redhat.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Tue, 23 Aug 2016 14:31:28 +0000 (16:31 +0200)]
dwc_eth_qos: fix interrupt enable race
We currently enable interrupts before we enable NAPI. If an RX interrupt
hits before we enabled NAPI then the NAPI callback is never called and
we leave the hardware with RX interrupts disabled, which of course leads
us to never handling received packets. Fix this by moving the interrupt
enable to after we've enable NAPI and the reclaim tasklet.
Fixes: cd5e41234729 ("dwc_eth_qos: do phy_start before resetting hardware") Signed-off-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamie Lentin [Mon, 22 Aug 2016 21:47:08 +0000 (22:47 +0100)]
net: mv88e6xxx: Fix ingress rate removal for mv6131 chips
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Xander Huff [Mon, 22 Aug 2016 20:57:16 +0000 (15:57 -0500)]
phy: micrel: Reenable interrupts during resume for ksz9031
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zefir Kurtisi [Mon, 22 Aug 2016 13:58:12 +0000 (15:58 +0200)]
gianfar: fix size of scatter-gathered frames
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zefir Kurtisi [Mon, 22 Aug 2016 13:56:38 +0000 (15:56 +0200)]
gianfar: prevent fragmentation in DSA environments
The eTSEC register MRBLR defines the maximum space in
the RX buffers and is set to 1536 by gianfar. This
reasonably covers the common use case where the MTU
is kept at default 1500. In that case, the largest
Ethernet frame size of 1518 plus an optional
GMAC_FCB_LEN of 8, and an additional padding of 8
to handle FSL_GIANFAR_DEV_HAS_TIMER totals to 1534
and nicely fit within the chosen MRBLR.
Alas, if the eTSEC is attached to a DSA enabled switch,
the (E)DSA header extension (4 or 8 bytes) causes every
maximum sized frame to be fragmented by the hardware.
This patch increases the maximum RX buffer size by 8
and rounds up to the next multiple of 64, which the
hardware's defines as RX buffer granularity.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Aug 2016 20:59:33 +0000 (13:59 -0700)]
udp: fix poll() issue with zero sized packets
Laura tracked poll() [and friends] regression caused by commit e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
udp_poll() needs to know if there is a valid packet in receive queue,
even if its payload length is 0.
Change first_packet_length() to return an signed int, and use -1
as the indication of an empty queue.
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing") Reported-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Laura Abbott <labbott@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Mon, 22 Aug 2016 11:10:20 +0000 (07:10 -0400)]
net sched: fix encoding to use real length
Encoding of the metadata was using the padded length as opposed to
the real length of the data which is a bug per specification.
This has not been an issue todate because all metadatum specified
so far has been 32 bit where aligned and data length are the same width.
This also includes a bug fix for validating the length of a u16 field.
But since there is no metadata of size u16 yes we are fine to include it
here.
While at it get rid of magic numbers.
Fixes: ef6980b6becb ("net sched: introduce IFE action") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 22 Aug 2016 09:03:29 +0000 (12:03 +0300)]
qed: FLR of active VFs might lead to FW assert
Driver never bothered marking the VF's vport with the VF's sw_fid.
As a result, FLR flows are not going to clean those vports.
If the vport was active when FLRed, re-activating it would lead
to a FW assertion.
Fixes: dacd88d6f6851 ("qed: IOV l2 functionality") Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
"net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs"
gso skbs arriving from an ingress interface that go through UDP
tunneling, are allowed to be fragmented if the resulting encapulated
segments exceed the dst mtu of the egress interface.
This aligned the behavior of gso skbs to non-gso skbs going through udp
encapsulation path.
However the non-gso vs gso anomaly is present also in the following
cases of a GRE tunnel:
- ip_gre in collect_md mode, where TUNNEL_DONT_FRAGMENT is not set
(e.g. OvS vport-gre with df_default=false)
- ip_gre in nopmtudisc mode, where IFLA_GRE_IGNORE_DF is set
In both of the above cases, the non-gso skbs get fragmented, whereas the
gso skbs (having skb_gso_network_seglen that exceeds dst mtu) get dropped,
as they don't go through the segment+fragment code path.
Fix: Setting IPSKB_FRAG_SEGS if the tunnel specified IP_DF bit is NOT set.
Tunnels that do set IP_DF, will not go to fragmentation of segments.
This preserves behavior of ip_gre in (the default) pmtudisc mode.
Fixes: b8247f095e ("net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs") Reported-by: wenxu <wenxu@ucloud.cn> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Tested-by: wenxu <wenxu@ucloud.cn> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Thu, 18 Aug 2016 13:39:40 +0000 (14:39 +0100)]
net: ipv6: Remove addresses for failures with strict DAD
If DAD fails with accept_dad set to 2, global addresses and host routes
are incorrectly left in place. Even though disable_ipv6 is set,
contrary to documentation, the addresses are not dynamically deleted
from the interface. It is only on a subsequent link down/up that these
are removed. The fix is not only to set the disable_ipv6 flag, but
also to call addrconf_ifdown(), which is the action to carry out when
disabling IPv6. This results in the addresses and routes being deleted
immediately. The DAD failure for the LL addr is determined as before
via netlink, or by the absence of the LL addr (which also previously
would have had to be checked for in case of an intervening link down
and up). As the call to addrconf_ifdown() requires an rtnl lock, the
logic to disable IPv6 when DAD fails is moved to addrconf_dad_work().
Previous behavior:
root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
5: eth3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2000::10/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:fe43:dd5a/64 scope link tentative dadfailed
valid_lft forever preferred_lft forever
root@vm1:/# ip -6 route show dev eth3
2000::/64 proto kernel metric 256
fe80::/64 proto kernel metric 256
root@vm1:/# ip link set down eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#
New behavior:
root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#
Signed-off-by: Mike Manning <mmanning@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mikko Rapeli [Mon, 22 Aug 2016 18:32:42 +0000 (20:32 +0200)]
include/uapi/linux/if_pppol2tp.h: include linux/in.h and linux/in6.h
Fixes userspace compilation errors like:
error: field ‘addr’ has incomplete type
struct sockaddr_in addr; /* IP address and port to send to */
^
error: field ‘addr’ has incomplete type
struct sockaddr_in6 addr; /* IP address and port to send to */
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
'Commit 3c8b3efc061a ("vmxnet3: allow variable length transmit data ring
buffer")' changed the size of the buffers in the tx data ring from a
fixed size of 128 bytes to a variable size.
However, while copying data to the data ring, vmxnet3_copy_hdr continues
to carry the old code that assumes fixed buffer size of 128. This patch
fixes it by adding correct offset based on the actual data ring buffer
size.
Signed-off-by: Guolin Yang <gyang@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 20 Aug 2016 03:58:26 +0000 (20:58 -0700)]
ixgbe: Do not clear RAR entry when clearing VMDq for SAN MAC
The RAR entry for the SAN MAC address was being cleared when we were
clearing the VMDq pool bits. In order to prevent this we need to add
an extra check to protect the SAN MAC from being cleared.
Fixes: 6e982aeae ("ixgbe: Clear stale pool mappings") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 3acb50c18d8d ("sctp: delay as much as possible skb_linearize") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some bug fixes for mlx5e driver.
From Saeed and Tariq, Optimize MTU change to not reset when it is not required.
From Paul, Command interface message length check to speedup firmware
command preparation.
From Mohamad, Save pci state when pci error is detected.
From Amir, Flow counters "lastuse" update fix.
From Hadar, Use correct flow dissector key on flower offloading.
Plus a small optimization for switchdev hardware id query.
From Or, three patches to address some E-Switch offloads issues.
For -stable of 4.6.y and 4.7.y:
net/mlx5e: Use correct flow dissector key on flower offloading
net/mlx5: Fix pci error recovery flow
net/mlx5: Added missing check of msg length in verifying its signature
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 18 Aug 2016 18:09:11 +0000 (21:09 +0300)]
net/mlx5: E-Switch, Avoid ACLs in the offloads mode
When we are in the switchdev/offloads mode, HW matching is done as
dictated by the offloaded rules and hence we don't need to enable
the ACLs mechanism used by the legacy mode.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 18 Aug 2016 18:09:10 +0000 (21:09 +0300)]
net/mlx5: E-Switch, Set the send-to-vport rules in the correct table
While adding actual offloading support to the new switchdev mode, we didn't
change the setup of the send-to-vport rules to put them in the slow path
table, fix that.
Fixes: 1033665e63b6 ('net/mlx5: E-Switch, Use two priorities for SRIOV offloads mode') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 18 Aug 2016 18:09:09 +0000 (21:09 +0300)]
net/mlx5: E-Switch, Return the correct devlink e-switch mode
Since mlx5 has also the NONE e-switch mode, we must translate from mlx5
mode to devlink mode on the devlink eswitch mode get call, do that.
While here, remove the mlx5_ prefix from the static function helpers
that deal with the mode to comply with the rest of the code.
Fixes: c930a3ad7453 ('net/mlx5e: Add devlink based SRIOV mode change') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Thu, 18 Aug 2016 18:09:08 +0000 (21:09 +0300)]
net/mlx5e: Retrieve the switchdev id from the firmware only once
Avoid firmware command execution each time the switchdev HW ID attr get
call is made. We do that by reading the ID (PF NIC MAC) only once at
load time and store it on the representor structure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Thu, 18 Aug 2016 18:09:07 +0000 (21:09 +0300)]
net/mlx5e: Use correct flow dissector key on flower offloading
The wrong key is used when extracting the address type field set by
the flower offload code. We have to use the control key and not the
basic key, fix that.
Fixes: e3a2b7ed018e ('net/mlx5e: Support offload cls_flower with drop action') Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Thu, 18 Aug 2016 18:09:06 +0000 (21:09 +0300)]
net/mlx5: Update last-use statistics for flow rules
Set lastuse statistic, when number of packets is changed compared to
last query. This was wrongly dropped when bulk counter reading was added.
Fixes: a351a1b03bf1 ('net/mlx5: Introduce bulk reading of flow counters') Signed-off-by: Amir Vadai <amirva@mellanox.com> Reported-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Thu, 18 Aug 2016 18:09:05 +0000 (21:09 +0300)]
net/mlx5: Added missing check of msg length in verifying its signature
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB
adapters') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xunlei Pang [Thu, 18 Aug 2016 04:33:28 +0000 (12:33 +0800)]
fib_trie: Fix the description of pos and bits
1) Fix one typo: s/tn/tp/
2) Fix the description about the "u" bits.
Signed-off-by: Xunlei Pang <xlpang@redhat.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki [Wed, 17 Aug 2016 13:37:14 +0000 (15:37 +0200)]
net: bgmac: fix reversed check for MII registration error
It was failing on successful registration returning meaningless errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Fixes: 55954f3bfdac ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file") Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 17 Aug 2016 12:56:26 +0000 (05:56 -0700)]
tcp: fix use after free in tcp_xmit_retransmit_queue()
When tcp_sendmsg() allocates a fresh and empty skb, it puts it at the
tail of the write queue using tcp_add_write_queue_tail()
Then it attempts to copy user data into this fresh skb.
If the copy fails, we undo the work and remove the fresh skb.
Unfortunately, this undo lacks the change done to tp->highest_sack and
we can leave a dangling pointer (to a freed skb)
Later, tcp_xmit_retransmit_queue() can dereference this pointer and
access freed memory. For regular kernels where memory is not unmapped,
this might cause SACK bugs because tcp_highest_sack_seq() is buggy,
returning garbage instead of tp->snd_nxt, but with various debug
features like CONFIG_DEBUG_PAGEALLOC, this can crash the kernel.
This bug was found by Marco Grassi thanks to syzkaller.
Fixes: 6859d49475d4 ("[TCP]: Abstract tp->highest_sack accessing & point to next skb") Reported-by: Marco Grassi <marco.gra@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Fixes resource allocation for ULD's in kdump kernel
At present the code to check in kdump kernel was not disabling
allocation of resources when CONFIG_CHELSIO_T4_DCB is defined, move the
code outside #defines so that it gets disabled irrespective of #define,
when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Tue, 16 Aug 2016 20:30:36 +0000 (13:30 -0700)]
net: thunderx: Fix OOPs with ethtool --register-dump
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com> Cc: <stable@vger.kernel.org> # 4.4.x- Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Tue, 16 Aug 2016 15:40:18 +0000 (18:40 +0300)]
qede: Fix Tx timeout due to xmit_more
Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.
At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.
While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].
Fixes: 312e06761c99 ("qede: Utilize xmit_more") Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter updates for your net tree,
they are:
1) Dump only conntrack that belong to this namespace via /proc file.
This is some fallout from the conversion to single conntrack table
for all netns, patch from Liping Zhang.
2) Missing MODULE_ALIAS_NF_LOGGER() for the ARP family that prevents
module autoloading, also from Liping Zhang.
3) Report overquota event to the right netnamespace, again from Liping.
4) Fix tproxy listener sk refcount that leads to crash, from
Eric Dumazet.
5) Fix racy refcounting on object deletion from nfnetlink and rule
removal both for nfacct and cttimeout, from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Liping Zhang [Thu, 18 Aug 2016 12:39:05 +0000 (20:39 +0800)]
netfilter: cttimeout: fix use after free error when delete netns
In general, when we want to delete a netns, cttimeout_net_exit will
be called before ipt_unregister_table, i.e. before ctnl_timeout_put.
But after call kfree_rcu in cttimeout_net_exit, we will still decrease
the timeout object's refcnt in ctnl_timeout_put, this is incorrect,
and will cause a use after free error.
It is easy to reproduce this problem:
# while : ; do
ip netns add xxx
ip netns exec xxx nfct add timeout testx inet icmp timeout 200
ip netns exec xxx iptables -t raw -p icmp -I OUTPUT -j CT --timeout testx
ip netns del xxx
done
=======================================================================
BUG kmalloc-96 (Tainted: G B E ): Poison overwritten
-----------------------------------------------------------------------
INFO: 0xffff88002b5161e8-0xffff88002b5161e8. First byte 0x6a instead of
0x6b
INFO: Allocated in cttimeout_new_timeout+0xd4/0x240 [nfnetlink_cttimeout]
age=104 cpu=0 pid=3330
___slab_alloc+0x4da/0x540
__slab_alloc+0x20/0x40
__kmalloc+0x1c8/0x240
cttimeout_new_timeout+0xd4/0x240 [nfnetlink_cttimeout]
nfnetlink_rcv_msg+0x21a/0x230 [nfnetlink]
[ ... ]
So only when the refcnt decreased to 0, we call kfree_rcu to free the
timeout object. And like nfnetlink_acct do, use atomic_cmpxchg to
avoid race between ctnl_timeout_try_del and ctnl_timeout_put.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Sat, 13 Aug 2016 15:13:01 +0000 (23:13 +0800)]
netfilter: nfnetlink_acct: fix race between nfacct del and xt_nfacct destroy
Suppose that we input the following commands at first:
# nfacct add test
# iptables -A INPUT -m nfacct --nfacct-name test
And now "test" acct's refcnt is 2, but later when we try to delete the
"test" nfacct and the related iptables rule at the same time, race maybe
happen:
CPU0 CPU1
nfnl_acct_try_del nfnl_acct_put
atomic_dec_and_test //ref=1,testfail -
- atomic_dec_and_test //ref=0,testok
- kfree_rcu
atomic_inc //ref=1 -
So after the rcu grace period, nf_acct will be freed but it is still linked
in the nfnl_acct_list, and we can access it later, then oops will happen.
Convert atomic_dec_and_test and atomic_inc combinaiton to one atomic
operation atomic_cmpxchg here to fix this problem.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
Roman Mashak [Sun, 14 Aug 2016 05:35:02 +0000 (22:35 -0700)]
net_sched: allow flushing tc police actions
The act_police uses its own code to walk the
action hashtable, which leads to that we could
not flush standalone tc police actions, so just
switch to tcf_generic_walker() like other actions.
(Joint work from Roman and Cong.)
Signed-off-by: Roman Mashak <mrv@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:35:01 +0000 (22:35 -0700)]
net_sched: unify the init logic for act_police
Jamal reported a crash when we create a police action
with a specific index, this is because the init logic
is not correct, we should always create one for this
case. Just unify the logic with other tc actions.
Fixes: a03e6fe56971 ("act_police: fix a crash during removal") Reported-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:35:00 +0000 (22:35 -0700)]
net_sched: convert tcf_exts from list to pointer array
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af265 ("net_sched: move tc_action into tcf_common") Reported-by: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:34:59 +0000 (22:34 -0700)]
net_sched: move tc offload macros to pkt_cls.h
struct tcf_exts belongs to filters, should not be visible
to plain tc actions.
Cc: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:34:58 +0000 (22:34 -0700)]
net_sched: fix a typo in tc_for_each_action()
It is harmless because all users pass 'a' to this macro.
Fixes: 00175aec941e ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef") Cc: Amir Vadai <amir@vadai.me> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:34:57 +0000 (22:34 -0700)]
net_sched: remove an unnecessary list_del()
This list_del() for tc action is not needed actually,
because we only use this list to chain bulk operations,
therefore should not be carried for latter operations.
Fixes: ec0595cc4495 ("net_sched: get rid of struct tcf_common") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sun, 14 Aug 2016 05:34:56 +0000 (22:34 -0700)]
net_sched: remove the leftover cleanup_a()
After refactoring tc_action into tcf_common, we no
longer need to cleanup temporary "actions" in list,
they are permanently stored in the hashtable.
Fixes: a85a970af265 ("net_sched: move tc_action into tcf_common") Reported-by: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 17 Aug 2016 23:20:24 +0000 (19:20 -0400)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-08-16
This series contains fixes to e1000e, igb, ixgbe and i40e.
Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.
Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.
Alex provides 2 patches for ixgbe now that he is back at Intel. First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs. Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.
Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch. To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 17 Aug 2016 23:18:34 +0000 (19:18 -0400)]
Merge branch 'mlxsw-fixes'
Jiri Pirko says:
====================
mlxsw: IPv4 UC router fixes
Ido says:
Patches 1-3 fix a long standing problem in the driver's init sequence,
which manifests itself quite often when routing daemons try to configure
an IP address on registered netdevs that don't yet have an associated
vPort.
Patches 4-9 add missing packet traps for the router to work properly and
also fix ordering issue following the recent changes to the driver's init
sequence.
The last patch isn't related to the router, but fixes a general problem
in which under certain conditions packets aren't trapped to CPU.
v1->v2:
- Change order of patch 7
- Add patch 6 following Ilan's comment
- Add patchset name and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:37 +0000 (16:39 +0200)]
mlxsw: spectrum: Allow packets to be trapped from any PG
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf06 ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support") Reported-by: Tamir Winetroub <tamirw@mellanox.com> Tested-by: Tamir Winetroub <tamirw@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:36 +0000 (16:39 +0200)]
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3f4 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:35 +0000 (16:39 +0200)]
mlxsw: spectrum: Add missing rollbacks in error path
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:33 +0000 (16:39 +0200)]
mlxsw: spectrum: Trap loop-backed packets
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Reported-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:31 +0000 (16:39 +0200)]
mlxsw: spectrum: Mark port as active before registering it
Commit bbf2a4757b30 ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b30 ("mlxsw: spectrum: Initialize ports at the end of init sequence") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:30 +0000 (16:39 +0200)]
mlxsw: spectrum: Create PVID vPort before registering netdevice
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:29 +0000 (16:39 +0200)]
mlxsw: spectrum: Remove redundant errors from the code
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 17 Aug 2016 14:39:28 +0000 (16:39 +0200)]
mlxsw: spectrum: Don't return upon error in removal path
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
inet_lookup_listener() and inet6_lookup_listener() no longer
take a reference on the found listener.
This minimal patch adds back the refcounting, but we might do
this differently in net-next later.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood") Reported-and-tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Wed, 17 Aug 2016 19:10:22 +0000 (12:10 -0700)]
Merge tag 'for-v4.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel.
* tag 'for-v4.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power_supply: tps65217-charger: fix missing platform_set_drvdata()
power: reset: hisi-reboot: Unmap region obtained by of_iomap
power: reset: reboot-mode: fix build error of missing ioremap/iounmap on UM
power: supply: max17042_battery: fix model download bug.
Liping Zhang [Sat, 13 Aug 2016 14:46:04 +0000 (22:46 +0800)]
netfilter: nfnetlink_log: add "nf-logger-3-1" module alias name
Otherwise, if nfnetlink_log.ko is not loaded, we cannot add rules
to log packets to the userspace when we specify it with arp family,
such as:
# nft add rule arp filter input log group 0
<cmdline>:1:1-37: Error: Could not process rule: No such file or
directory
add rule arp filter input log group 0
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Mon, 15 Aug 2016 13:50:35 +0000 (21:50 +0800)]
netfilter: conntrack: do not dump other netns's conntrack entries via proc
We should skip the conntracks that belong to a different namespace,
otherwise other unrelated netns's conntrack entries will be dumped via
/proc/net/nf_conntrack.
Fixes: 56d52d4892d0 ("netfilter: conntrack: use a single hashtable for all namespaces") Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / linux-beck.git / log