Turning off led on port 0 of the 5719 serdes causes all other ports to
lose power and stop functioning. Add tg3_phy_led_bug() function to check
for this condition. We use a switch() in tg3_phy_led_bug() for
consistency with the tg3_phy_power_bug() function.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RFC 4443 has defined two additional codes for ICMPv6 type 1 (destination
unreachable) messages:
5 - Source address failed ingress/egress policy
6 - Reject route to destination
Now they are treated as protocol error and icmpv6_err_convert() converts them
to EPROTO.
RFC 4443 says:
"Codes 5 and 6 are more informative subsets of code 1."
Treat codes 5 and 6 as code 1 (EACCES)
Btw, connect() returning -EPROTO confuses firefox, so that fallback to
other/IPv4 addresses does not work:
https://bugzilla.mozilla.org/show_bug.cgi?id=910773
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While looking into MLDv1/v2 code, I noticed that bridging code does
not convert it's max delay into jiffies for MLDv2 messages as we do
in core IPv6' multicast code.
RFC3810, 5.1.3. Maximum Response Code says:
The Maximum Response Code field specifies the maximum time allowed
before sending a responding Report. The actual time allowed, called
the Maximum Response Delay, is represented in units of milliseconds,
and is derived from the Maximum Response Code as follows: [...]
As we update timers that work with jiffies, we need to convert it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Linus Lüssing <linus.luessing@web.de> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8728c544a9cbdc ("net: dev_pick_tx() fix") and commit b6fe83e9525a ("bonding: refine IFF_XMIT_DST_RELEASE capability")
are quite incompatible : Queue selection is disabled because skb
dst was dropped before entering bonding device.
This causes major performance regression, mainly because TCP packets
for a given flow can be sent to multiple queues.
This is particularly visible when using the new FQ packet scheduler
with MQ + FQ setup on the slaves.
We can safely revert the first commit now that 416186fbf8c5b
("net: Split core bits of netdev_pick_tx into __netdev_pick_tx")
properly caps the queue_index.
Reported-by: Xi Wang <xii@google.com> Diagnosed-by: Xi Wang <xii@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Denys Fedorysychenko <nuclearcat@nuclearcat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Should a connect fail, if the publication/server is unavailable or
due to some other error, a positive value will be returned and errno
is never set. If the application code checks for an explicit zero
return from connect (success) or a negative return (failure), it
will not catch the error and subsequent send() calls will fail as
shown from the strace snippet below.
The reason for this behaviour is that TIPC wrongly inverts error
codes set in sk_err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 90ba9b19 (tcp: tcp_make_synack() can use alloc_skb()), Eric changed
the call to sock_wmalloc in tcp_make_synack to alloc_skb. In doing so,
the netfilter owner match lost its ability to block the SYNACK packet on
outbound listening sockets. Revert the change, restoring the owner match
functionality.
This closes netfilter bugzilla #847.
Signed-off-by: Phil Oester <kernel@linuxace.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating skbs when sending out neighbour discovery messages
currently uses sock_alloc_send_skb() based on a per net namespace
socket and thus share a socket wmem buffer space.
If a netdevice is temporarily unable to transmit due to carrier
loss or for other reasons, the queued up ndisc messages will cosnume
all of the wmem space and will thus prevent from any more skbs to
be allocated even for netdevices that are able to transmit packets.
The number of neighbour discovery messages sent is very limited,
use of alloc_skb() bypasses the socket wmem buffer size enforcement
while the manual call to skb_set_owner_w() maintains the socket
reference needed for the IPv6 output path.
This patch has orginally been posted by Eric Dumazet in a modified
form.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Chris Clark <chris.clark@alcatel-lucent.com> Bisected-by: Chris Clark <chris.clark@alcatel-lucent.com> Tested-by: Chris Clark <chris.clark@alcatel-lucent.com> Suggested-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Chris Clark <chris.clark@alcatel-lucent.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The zero value means that tsecr is not valid, so it's a special case.
tsoffset is used to customize tcp_time_stamp for one socket.
tsoffset is usually zero, it's used when a socket was moved from one
host to another host.
Currently this issue affects logic of tcp_rcv_rtt_measure_ts. Due to
incorrect value of rcv_tsecr, tcp_rcv_rtt_measure_ts sets rto to
TCP_RTO_MAX.
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit 844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 385904f819e3 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time. This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b765b79 ("htb: improved accuracy at high rates")
broke the "linklayer atm" handling.
tc class add ... htb rate X ceil Y linklayer atm
The linklayer setting is implemented by modifying the rate table
which is send to the kernel. No direct parameter were
transferred to the kernel indicating the linklayer setting.
The commit 56b765b79 ("htb: improved accuracy at high rates")
removed the use of the rate table system.
To keep compatible with older iproute2 utils, this patch detects
the linklayer by parsing the rate table. It also supports future
versions of iproute2 to send this linklayer parameter to the
kernel directly. This is done by using the __reserved field in
struct tc_ratespec, to convey the choosen linklayer option, but
only using the lower 4 bits of this field.
Linklayer detection is limited to speeds below 100Mbit/s, because
at high rates the rtab is gets too inaccurate, so bad that
several fields contain the same values, this resembling the ATM
detect. Fields even start to contain "0" time to send, e.g. at
1000Mbit/s sending a 96 bytes packet cost "0", thus the rtab have
been more broken than we first realized.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getsockopt PACKET_STATISTICS returns tp_packets + tp_drops. Commit ee80fbf301 ("packet: account statistics only in tpacket_stats_u")
cleaned up the getsockopt PACKET_STATISTICS code.
This also changed semantics. Historically, tp_packets included
tp_drops on return. The commit removed the line that adds tp_drops
into tp_packets.
This patch reinstates the old semantics.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent.
The "when" field must be set for such skb. It's used in tcp_rearm_rto
for example. If the "when" field isn't set, the retransmit timeout can
be calculated incorrectly and a tcp connected can stop for two minutes
(TCP_RTO_MAX).
Acked-by: Pavel Emelyanov <xemul@parallels.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not allowed for an ipv6 packet to contain multiple fragmentation
headers. So discard packets which were already reassembled by
fragmentation logic and send back a parameter problem icmp.
The updates for RFC 6980 will come in later, I have to do a bit more
research here.
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:
<http://seclists.org/oss-sec/2012/q4/292>
But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.
Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.
This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).
Thanks to Ding Tianhong to bring this topic up again.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: George Kargiotakis <kargig@void.gr> Cc: P J P <ppandit@redhat.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent fix d9bf5f1309 "tun: compare with 0 instead of total_len" is
not totally correct. Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the iproute2 command `bridge vlan show`, after switching from
rtgenmsg to ifinfomsg.
Let's start with a little history:
Feb 20: Vlad Yasevich got his VLAN-aware bridge patchset included in
the 3.9 merge window.
In the kernel commit 6cbdceeb, he added attribute support to
bridge GETLINK requests sent with rtgenmsg.
Mar 6th: Vlad got this iproute2 reference implementation of the bridge
vlan netlink interface accepted (iproute2 9eff0e5c)
Apr 25th: iproute2 switched from using rtgenmsg to ifinfomsg (63338dca)
http://patchwork.ozlabs.org/patch/239602/
http://marc.info/?t=136680900700007
Apr 28th: Linus released 3.9
Apr 30th: Stephen released iproute2 3.9.0
The `bridge vlan show` command haven't been working since the switch to
ifinfomsg, or in a released version of iproute2. Since the kernel side
only supports rtgenmsg, which iproute2 switched away from just prior to
the iproute2 3.9.0 release.
I haven't been able to find any documentation, about neither rtgenmsg
nor ifinfomsg, and in which situation to use which, but kernel commit 88c5b5ce seams to suggest that ifinfomsg should be used.
Fixing this in kernel will break compatibility, but I doubt that anybody
have been using it due to this bug in the user space reference
implementation, at least not without noticing this bug. That said the
functionality is still fully functional in 3.9, when reversing iproute2
commit 63338dca.
This could also be fixed in iproute2, but thats an ugly patch that would
reintroduce rtgenmsg in iproute2, and from searching in netdev it seams
like rtgenmsg usage is discouraged. I'm assuming that the only reason
that Vlad implemented the kernel side to use rtgenmsg, was because
iproute2 was using it at the time.
Signed-off-by: Asbjoern Sloth Toennesen <ast@fiberby.net> Reviewed-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using inner-id for tunnel id is not safe in some rare cases.
E.g. packets coming from multiple sources entering same tunnel
can have same id. Therefore on tunnel packet receive we
could have packets from two different stream but with same
source and dst IP with same ip-id which could confuse ip packet
reassembly.
Following patch reverts optimization from commit 490ab08127 (IP_GRE: Fix IP-Identification.)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jarno Rajahalme <jrajahalme@nicira.com> CC: Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netlink dump operations take module as parameter to hold
reference for entire netlink dump duration.
Currently it holds ref only on genl module which is not correct
when we use ops registered to genl from another module.
Following patch adds module pointer to genl_ops so that netlink
can hold ref count on it.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jesse Gross <jesse@nicira.com> CC: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of genl-family with parallel ops off, dumpif() callback
is expected to run under genl_lock, But commit def3117493eafd9df
(genl: Allow concurrent genl callbacks.) changed this behaviour
where only first dumpit() op was called under genl-lock.
For subsequent dump, only nlk->cb_lock was taken.
Following patch fixes it by defining locked dumpit() and done()
callback which takes care of genl-locking.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jesse Gross <jesse@nicira.com> CC: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ipgre_header() (header_ops->create) to return the correct
amount of bytes pushed. Most callers of dev_hard_header() seem
to care only if it was success, but af_packet.c uses it as
offset to the skb to copy from userspace only once. In practice
this fixes packet socket sendto()/sendmsg() to gre tunnels.
Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a subtree did not match we currently stop backtracking and return
NULL (root table from fib_lookup). This could yield in invalid routing
table lookups when using subtrees.
Instead continue to backtrack until a valid subtree or node is found
and return this match.
Also remove unneeded NULL check.
Reported-by: Teco Boot <teco@inf-net.nl> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Cc: David Lamparter <equinox@diac24.net> Cc: <boutier@pps.univ-paris-diderot.fr> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While investigating about strange increase of retransmit rates
on hosts ~24 days after boot, Van found hystart was disabled
if ca->epoch_start was 0, as following condition is true
when tcp_time_stamp high order bit is set.
(s32)(tcp_time_stamp - ca->epoch_start) < HZ
Quoting Van :
At initialization & after every loss ca->epoch_start is set to zero so
I believe that the above line will turn off hystart as soon as the 2^31
bit is set in tcp_time_stamp & hystart will stay off for 24 days.
I think we've observed that cubic's restart is too aggressive without
hystart so this might account for the higher drop rate we observe.
Diagnosed-by: Van Jacobson <vanj@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are reading an uninitialized value for the max_delay
variable when snooping an MLD query message of invalid length and would
update our timers with that.
Fixing this by simply ignoring such broken MLD queries (just like we do
for IGMP already).
This is a regression introduced by:
"bridge: disable snooping if there is no querier" (b00589af3b04)
Reported-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, on neighbour creation, bond_neigh_init() will be called with a
foreign netdev.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev->ndo_neigh_setup() might need some of the values of neigh_parms, so
populate them before calling it.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df8ef8f3aaa6692970a436204c4429210addb23a
macvlan: add FDB bridge ops and macvlan flags
added a flags field to macvlan, which can be
controlled from userspace.
The idea is to make the interface future-proof
so we can add flags and not new fields.
However, flags value isn't validated, as a result,
userspace can't detect which flags are supported.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.
The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Reported-by: Changli Gao <xiaosuo@gmail.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5c766d642 ("ipv4: introduce address lifetime") leaves the ifa
resource that was allocated via inet_alloc_ifa() unfreed when returning
the function with -EINVAL. Thus, free it first via inet_free_ifa().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Reviewed-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace passes a large priority value
the assignment of the unsigned value hopt->prio
to signed int cl->prio causes cl->prio to become negative and the
comparison is with TC_HTB_NUMPRIO is always false.
The result is that HTB crashes by referencing outside
the array when processing packets. With this patch the large value
wraps around like other values outside the normal range.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Zhouping Liu <zliu@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PREEMPT is enabled, Linux will not be able to boot and warn:
[ 4.127825] ------------[ cut here ]------------
[ 4.133376] WARNING: at init/main.c:699 do_one_initcall+0x150/0x158()
[ 4.140738] initcall xen_init_events+0x0/0x10c returned with preemption imbalance
This is because xen_percpu_init uses get_cpu but doesn't have the corresponding
put_cpu.
This patch addresses a potential NULL pointer dereference regression in
iscsit_setup_nop_out() code, specifically for two cases when a solicited
NOPOUT triggers a ISCSI_REASON_PROTOCOL_ERROR reject to be generated.
This is because iscsi_cmd is expected to be NULL for solicited NOPOUT
case before iscsit_process_nop_out() locates the descriptor via TTT
using iscsit_find_cmd_from_ttt().
This patch fixes a bug in __iscsi_target_login_thread() where an explicit
network portal thread reset ends up leaking the iscsit_transport module
reference, along with the associated iscsi_conn allocation.
This manifests itself with iser-target where a NP reset causes the extra
iscsit_transport reference to be taken in iscsit_conn_set_transport()
during the reset, which prevents the ib_isert module from being unloaded
after the NP thread shutdown has finished.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a regression bug within ImmediateData=Yes failure
handling that ends up triggering an OOPs within >= v3.10 iscsi-target
code.
The problem occurs when iscsit_process_scsi_cmd() does the call to
target_put_sess_cmd(), and once again in iscsit_get_immediate_data()
that is triggered during two different cases:
- When iscsit_sequence_cmd() returns CMDSN_LOWER_THAN_EXP, for which
the descriptor state will already have been set to ISTATE_REMOVE
by iscsit_sequence_cmd(), and
- When iscsi_cmd->sense_reason is set, for which iscsit_execute_cmd()
will have already called transport_send_check_condition_and_sense()
to queue the exception response.
It changes iscsit_process_scsi_cmd() to drop the early call, and makes
iscsit_get_immediate_data() call target_put_sess_cmd() from a single
location after dumping the immediate data for the failed command.
The regression was initially introduced in commit:
This patch fixes spc_emulate_inquiry_std() to add trailing ASCII
spaces for INQUIRY vendor + model fields following SPC-4 text:
"ASCII data fields described as being left-aligned shall have any
unused bytes at the end of the field (i.e., highest offset) and
the unused bytes shall be filled with ASCII space characters (20h)."
This addresses a problem with Falconstor NSS multipathing.
Reported-by: Tomas Molota <tomas.molota@lightstorm.sk> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
The PLL hang workaround is required only for AR9330 and
AR9340. This issue was first observed on an AP121 and the WAR
is enabled for AR9340 also (DB120 etc.), since it uses a PLL
design identical to AR9330. This is not required for AR9485 and AR9550.
ath9k_htc adds padding between the 802.11 header and the payload during
TX by moving the header. When handing the frame back to mac80211 for TX
status handling the header is not moved back into its original position.
This can result in a too small skb headroom when entering ath9k_htc
again (due to a soft retransmission for example) causing an
skb_under_panic oops.
Fix this by moving the 802.11 header back into its original position
before returning the frame to mac80211 as other drivers like rt2x00
or ath5k do.
Reported-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that we missed increasing needed pages in BRK to
mapping initial 2M and [0,1M) when we switched to use the #PF
handler to set memory mappings:
> commit 8170e6bed465b4b0c7687f93e9948aca4358a33b
> Author: H. Peter Anvin <hpa@zytor.com>
> Date: Thu Jan 24 12:19:52 2013 -0800
>
> x86, 64bit: Use a #PF handler to materialize early mappings on demand
Before that, we had the maping from [0,512M) in head_64.S, and we
can spare two pages [0-1M). After that change, we can not reuse
pages anymore.
When we have more than 512M ram, we need an extra page for pgd page
with [512G, 1024g).
Increase pages in BRK for page table to solve the boot crash.
Reported-by: Dave Hansen <dave.hansen@intel.com> Bisected-by: Dave Hansen <dave.hansen@intel.com> Tested-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/1376351004-4015-1-git-send-email-yinghai@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some architectures, such as ARM-32 do not return the same base address
when you call kmap_atomic() twice on the same page.
This causes problems for the memmove() call in the XDR helper routine
"_shift_data_right_pages()", since it defeats the detection of
overlapping memory ranges, and has been seen to corrupt memory.
The fix is to distinguish between the case where we're doing an
inter-page copy or not. In the former case of we know that the memory
ranges cannot possibly overlap, so we can additionally micro-optimise
by replacing memmove() with memcpy().
Reported-by: Mark Young <MYoung@nvidia.com> Reported-by: Matt Craighead <mcraighead@nvidia.com> Cc: Bruce Fields <bfields@fieldses.org> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Tested-by: Matt Craighead <mcraighead@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes eDP link-training failures and cases where all voltage swing
/pre-emphasis levels were tried and failed during clock recovery and -
as a fallback - we go on to do channel equalization with the last voltage
swing/pre-emphasis level which will succeed. Both issues can lead to a
blank screen.
v2:
- improve commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64880 Tested-by: Jeremy Moles <cubicool@gmail.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If !PREEMPT, a kworker running work items back to back can hog CPU.
This becomes dangerous when a self-requeueing work item which is
waiting for something to happen races against stop_machine. Such
self-requeueing work item would requeue itself indefinitely hogging
the kworker and CPU it's running on while stop_machine would wait for
that CPU to enter stop_machine while preventing anything else from
happening on all other CPUs. The two would deadlock.
Jamie Liu reports that this deadlock scenario exists around
scsi_requeue_run_queue() and libata port multiplier support, where one
port may exclude command processing from other ports. With the right
timing, scsi_requeue_run_queue() can end up requeueing itself trying
to execute an IO which is asked to be retried while another device has
an exclusive access, which in turn can't make forward progress due to
stop_machine.
Fix it by invoking cond_resched() after executing each work item.
If the system had a few memory groups and all of them were destroyed,
memcg_limited_groups_array_size has non-zero value, but all new caches
are created without memcg_params, because memcg_kmem_enabled() returns
false.
We try to enumirate child caches in a few places and all of them are
potentially dangerous.
For example my kernel is compiled with CONFIG_SLAB and it crashed when I
tryed to mount a NFS share after a few experiments with kmemcg.
"cat /sys/devices/system/memory/memory*/removable" crashed the system.
The problem is that show_mem_removable() is passing a
bad pfn to is_mem_section_removable(), which causes
if (!node_online(page_to_nid(page)))
to blow up. Why is it passing in a bad pfn?
The reason is that show_mem_removable() will loop sections_per_block
times. sections_per_block is 16, but mem->section_count is 8,
indicating holes in this memory block. Checking that the memory section
is present before checking to see if the memory section is removable
fixes the problem.
According to 'man msgrcv': "If msgtyp is less than 0, the first message of
the lowest type that is less than or equal to the absolute value of msgtyp
shall be received."
Bug: The kernel only returns a message if its type is 1; other messages
with type < abs(msgtype) will never get returned.
Fix: After having traversed the list to find the first message with the
lowest type, we need to actually return that message.
This regression was introduced by commit daaf74cf0867 ("ipc: refactor
msg list search into separate function")
Signed-off-by: Svenning Soerensen <sss@secomea.dk> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct an issue with /proc/timer_list reported by Holger.
When reading from the proc file with a sufficiently small buffer, 2k so
not really that small, there was one could get hung trying to read the
file a chunk at a time.
The timer_list_start function failed to account for the possibility that
the offset was adjusted outside the timer_list_next.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com> Reported-by: Holger Hans Peter Freyther <holger@freyther.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Berke Durak <berke.durak@xiphos.com> Cc: Jeff Layton <jlayton@redhat.com> Tested-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of WARN_ON() needs the definitions from bug.h, without it
you can get:
include/linux/regmap.h: In function 'regmap_write':
include/linux/regmap.h:525:2: error: implicit declaration of function 'WARN_ONCE' [-Werror=implicit-function-declaration]
Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This solves a problem observed in kexec'ed kernel where 200ms timeout is
too short and bootconsole fails to initialize. Console did eventually
become workable but much later into the boot process.
Observed timeout was around 260ms, but I decided to make it a little bigger
for more reliability.
This has been tested on Power7 machine with Petitboot as a primary
bootloader and PowerNV firmware.
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
NFSv4 reserves readdir cookie values 0-2 for special entries (. and ..),
but jfs allows a value of 2 for a non-special entry. This incompatibility
can result in the nfs client reporting a readdir loop.
This patch doesn't change the value stored internally, but adds one to
the value exposed to the iterate method.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
[bwh: Backported to 3.2:
- Adjust context
- s/ctx->pos/filp->f_pos/] Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. MEI_INTEROP_TIMEOUT is in seconds not in jiffies
so we use mei_secs_to_jiffies macro
While cold boot is fast this is relevant in resume
2. wait_event_interruptible_timeout can return with
-ERESTARTSYS so do not override it with -ETIMEDOUT
3.Adjust error message
ME HW ready bit is down after hw reset was asserted or on error.
Only on error we need to enter the reset flow, additional reset
need to be prevented when reset was triggered during
initialization , power up/down or a reset is already in progress
If there are UNUSABLE regions in the machine memory map, dom0 will
attempt to map them 1:1 which is not permitted by Xen and the kernel
will crash.
There isn't anything interesting in the UNUSABLE region that the dom0
kernel needs access to so we can avoid making the 1:1 mapping and
treat it as RAM.
We only do this for dom0, as that is where tboot case shows up.
A PV domU could have an UNUSABLE region in its pseudo-physical map
and would need to be handled in another patch.
This fixes a boot failure on hosts with tboot.
tboot marks a region in the e820 map as unusable and the dom0 kernel
would attempt to map this region and Xen does not permit unusable
regions to be mapped by guests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[v1: Altered the patch and description with domU's with UNUSABLE regions] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the updated version of df54d6fa5427 ("x86 get_unmapped_area():
use proper mmap base for bottom-up direction") that only randomizes the
mmap base address once.
Signed-off-by: Radu Caragea <sinaelgl@gmail.com> Reported-and-tested-by: Jeff Shorey <shoreyjeff@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michel Lespinasse <walken@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Adrian Sendroiu <molecula2788@gmail.com> Cc: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit isn't necessarily wrong, but because it recalculates the
random mmap_base every time, it seems to confuse user memory allocators
that expect contiguous mmap allocations even when the mmap address isn't
specified.
In particular, the MATLAB Java runtime seems to be unhappy. See
https://bugzilla.kernel.org/show_bug.cgi?id=60774
So we'll want to apply the random offset only once, and Radu has a patch
for that. Revert this older commit in order to apply the other one.
Reported-by: Jeff Shorey <shoreyjeff@gmail.com> Cc: Radu Caragea <sinaelgl@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a nasty bug in the SCSI SG_IO ioctl that in some circumstances
leads to one process writing data into the address space of some other
random unrelated process if the ioctl is interrupted by a signal.
What happens is the following:
- A process issues an SG_IO ioctl with direction DXFER_FROM_DEV (ie the
underlying SCSI command will transfer data from the SCSI device to
the buffer provided in the ioctl)
- Before the command finishes, a signal is sent to the process waiting
in the ioctl. This will end up waking up the sg_ioctl() code:
result = wait_event_interruptible(sfp->read_wait,
(srp_done(sfp, srp) || sdp->detached));
but neither srp_done() nor sdp->detached is true, so we end up just
setting srp->orphan and returning to userspace:
srp->orphan = 1;
write_unlock_irq(&sfp->rq_list_lock);
return result; /* -ERESTARTSYS because signal hit process */
At this point the original process is done with the ioctl and
blithely goes ahead handling the signal, reissuing the ioctl, etc.
- Eventually, the SCSI command issued by the first ioctl finishes and
ends up in sg_rq_end_io(). At the end of that function, we run through:
write_lock_irqsave(&sfp->rq_list_lock, iflags);
if (unlikely(srp->orphan)) {
if (sfp->keep_orphan)
srp->sg_io_owned = 0;
else
done = 0;
}
srp->done = done;
write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
if (likely(done)) {
/* Now wake up any sg_read() that is waiting for this
* packet.
*/
wake_up_interruptible(&sfp->read_wait);
kill_fasync(&sfp->async_qp, SIGPOLL, POLL_IN);
kref_put(&sfp->f_ref, sg_remove_sfp);
} else {
INIT_WORK(&srp->ew.work, sg_rq_end_io_usercontext);
schedule_work(&srp->ew.work);
}
Since srp->orphan *is* set, we set done to 0 (assuming the
userspace app has not set keep_orphan via an SG_SET_KEEP_ORPHAN
ioctl), and therefore we end up scheduling sg_rq_end_io_usercontext()
to run in a workqueue.
- In workqueue context we go through sg_rq_end_io_usercontext() ->
sg_finish_rem_req() -> blk_rq_unmap_user() -> ... ->
bio_uncopy_user() -> __bio_copy_iov() -> copy_to_user().
The key point here is that we are doing copy_to_user() on a
workqueue -- that is, we're on a kernel thread with current->mm
equal to whatever random previous user process was scheduled before
this kernel thread. So we end up copying whatever data the SCSI
command returned to the virtual address of the buffer passed into
the original ioctl, but it's quite likely we do this copying into a
different address space!
As suggested by James Bottomley <James.Bottomley@hansenpartnership.com>,
add a check for current->mm (which is NULL if we're on a kernel thread
without a real userspace address space) in bio_uncopy_user(), and skip
the copy if we're on a kernel thread.
There's no reason that I can think of for any caller of bio_uncopy_user()
to want to do copying on a kernel thread with a random active userspace
address space.
Huge thanks to Costa Sapuntzakis <costa@purestorage.com> for the
original pointer to this bug in the sg code.
Signed-off-by: Roland Dreier <roland@purestorage.com> Tested-by: David Milburn <dmilburn@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want ppc64 to be able to select between optimised assembly
checksum routines in big endian and the generic lib/checksum.c
routines in little endian.
The lpfc driver is forcing CONFIG_GENERIC_CSUM on which means
we are unable to make the decision to enable it in the arch
Kconfig. If the option exists it is always forced on.
This got introduced in 3.10 via commit 6a7252fdb0c3 ([SCSI] lpfc:
fix up Kconfig dependencies). I spoke to Randy about it and
the original issue was with CRC_T10DIF not being defined.
As such, remove the select of CONFIG_GENERIC_CSUM.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, the ref_count for some scsi_device drops down to zero,
triggering device removal through execute_in_process_context(), while
the lldd error recovery thread iterates through a scsi device list.
Unfortunately, execute_in_process_context() decides to immediately
execute that device removal function, instead of scheduling asynchronous
execution, since it detects process context and thinks it is safe to do
so. But almost all calls to shost_for_each_device() in our lldd are
inside spin_lock_irq, even in thread context. Obviously, schedule()
inside spin_lock_irq sections is a bad idea.
Change the lldd to use the proper iterator function,
__shost_for_each_device(), in combination with required locking.
Occurences that need to be changed include all calls in zfcp_erp.c,
since those might be executed in zfcp error recovery thread context
with a lock held.
Other occurences of shost_for_each_device() in zfcp_fsf.c do not
need to be changed (no process context, no surrounding locking).
The problem was introduced in Linux 2.6.37 by commit b62a8d9b45b971a67a0f8413338c230e3117dff5
"[SCSI] zfcp: Use SCSI device data zfcp_scsi_dev instead of zfcp_unit".
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds wait_event_interruptible_lock_irq_timeout(), which is a
straight-forward descendant of wait_event_interruptible_timeout() and
wait_event_interruptible_lock_irq().
The zfcp driver used to call wait_event_interruptible_timeout()
in combination with some intricate and error-prone locking. Using
wait_event_interruptible_lock_irq_timeout() as a replacement
nicely cleans up that locking.
This rework removes a situation that resulted in a locking imbalance
in zfcp_qdio_sbal_get():
BUG: workqueue leaked lock or atomic: events/1/0xffffff00/10
last function: zfcp_fc_wka_port_offline+0x0/0xa0 [zfcp]
It was introduced by commit c2af7545aaff3495d9bf9a7608c52f0af86fb194
"[SCSI] zfcp: Do not wait for SBALs on stopped queue", which had a new
code path related to ZFCP_STATUS_ADAPTER_QDIOUP that took an early exit
without a required lock being held. The problem occured when a
special, non-SCSI I/O request was being submitted in process context,
when the adapter's queues had been torn down. In this case the bug
surfaced when the Fibre Channel port connection for a well-known address
was closed during a concurrent adapter shut-down procedure, which is a
rare constellation.
This patch also fixes these warnings from the sparse tool (make C=1):
drivers/s390/scsi/zfcp_qdio.c:224:12: warning: context imbalance in
'zfcp_qdio_sbal_check' - wrong count at exit
drivers/s390/scsi/zfcp_qdio.c:244:5: warning: context imbalance in
'zfcp_qdio_sbal_get' - unexpected unlock
Last but not least, we get rid of that crappy lock-unlock-lock
sequence at the beginning of the critical section.
It is okay to call zfcp_erp_adapter_reopen() with req_q_lock held.
As Arjan pointed out, we mustn't do anything related to PCI
configuration until the device is properly enabled with
pci_enable_device().
Reported-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because we nulify ctx->vif in iwlagn_mac_remove_interface()
before calling some other functions that teardown interface. To fix
just check ctx->vif on iwl_chswitch_done(). We should not call
ieee80211_chswitch_done() as channel switch works were already canceled
by mac80211 in ieee80211_do_stop() -> ieee80211_mgd_stop().
Fixing support for the Silicon Image 3826 port multiplier, by applying
to it the same quirks applied to the Silicon Image 3726. Specifically
fixes the repeated timeout/reset process which previously afflicted
the 3726, as described from line 290. Slightly based on notes from:
We want the data stored in "addr" and "qual", but the extra ampersands
mean we are copying stack data instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Being a low-level component, various drivers (e.g. olpc-battery) assume
that it is ok to communicate with the OLPC Embedded Controller during
probe. Therefore the OLPC EC driver must be initialised before other
drivers try to use it. This was the case until it was recently moved
out of arch/x86 and restructured around commits ac2504151f5a ("Platform:
OLPC: turn EC driver into a platform_driver") and 85f90cf6ca56 ("x86:
OLPC: switch over to using new EC driver on x86").
Use arch_initcall so that olpc-ec is readied earlier, matching the
previous behaviour.
Fixes a regression introduced in Linux-3.6 where various drivers such as
olpc-battery and olpc-xo1-sci failed to load due to an inability to
communicate with the EC. The user-visible effect was a lack of battery
monitoring, missing ebook/lid switch input devices, etc.
Signed-off-by: Daniel Drake <dsd@laptop.org> Cc: Andres Salomon <dilinger@queued.net> Cc: Paul Fox <pgf@laptop.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue with improper counting number of flying bio requests for
BIO_EOPNOTSUPP error detection case.
The sb_nbio must be incremented exactly the same number of times as
complete() function was called (or will be called) because
nilfs_segbuf_wait() will call wail_for_completion() for the number of
times set to sb_nbio:
do {
wait_for_completion(&segbuf->sb_bio_event);
} while (--segbuf->sb_nbio > 0);
Two functions complete() and wait_for_completion() must be called the
same number of times for the same sb_bio_event. Otherwise,
wait_for_completion() will hang or leak.
Remove double call of bio_put() in nilfs_end_bio_write() for the case of
BIO_EOPNOTSUPP error detection. The issue was found by Dan Carpenter
and he suggests first version of the fix too.
Already existing property flags are filled wrong for properties created from
initial FDT. This could cause problems if this DYNAMIC device-tree functions
are used later, i.e. properties are attached/detached/replaced. Simply dumping
flags from the running system show, that some initial static (not allocated via
kzmalloc()) nodes are marked as dynamic.
I putted some debug extensions to property_proc_show(..) :
..
+ if (OF_IS_DYNAMIC(pp))
+ pr_err("DEBUG: xxx : OF_IS_DYNAMIC\n");
+ if (OF_IS_DETACHED(pp))
+ pr_err("DEBUG: xxx : OF_IS_DETACHED\n");
when you operate on the nodes (e.g.: ~$ cat /proc/device-tree/*some_node*) you
will see that those flags are filled wrong, basically in most cases it will dump
a DYNAMIC or DETACHED status, which is in not true.
(BTW. this OF_IS_DETACHED is a own define for debug purposes which which just
make a test_bit(OF_DETACHED, &x->_flags)
If nodes are dynamic kernel is allowed to kfree() them. But it will crash
attempting to do so on the nodes from FDT -- they are not allocated via
kzmalloc().
Signed-off-by: Wladislav Wiebe <wladislav.kw@gmail.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@nsn.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After any "soft gfx reset" we must manually invalidate the TLBs
associated with each ring. Empirically, it seems that a
suspend/resume or D3-D0 cycle count as a "soft reset". The symptom is
that the hardware would fail to note the new address for its status
page, and so it would continue to write the shadow registers and
breadcrumbs into the old physical address (now used by something
completely different, scary). Whereas the driver would read the new
status page and never see any progress, it would appear that the GPU
hung immediately upon resume.
Based on a patch by naresh kumar kachhi <naresh.kumar.kacchi@intel.com>
Reported-by: Thiago Macieira <thiago@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64725 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Thiago Macieira <thiago@kde.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug (introduced in 3.10) in WREG32_OR made
commit d3418eacad403033e95e49dc14afa37c2112c134
"drm/radeon/evergreen: setup HDMI before enabling it"
cause a regression. Sometimes audio over HDMI wasn't working, sometimes
display was corrupted.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60687
https://bugzilla.kernel.org/show_bug.cgi?id=60709
https://bugs.freedesktop.org/show_bug.cgi?id=67767
projects / karo-tx-linux.git / log