Jérémy Lefaure [Fri, 17 Mar 2017 01:51:33 +0000 (21:51 -0400)]
tpm/tpm_crb: fix unused warnings on suspend/resume functions
When PM_SLEEP is disabled crb_pm_suspend and crb_pm_resume are not used by
SET_SYSTEM_SLEEP_PM_OPS even if PM is enabled:
drvers/char/tpm/tpm_crb.c:540:12: warning: ‘crb_pm_suspend’ defined but not
used [-Wunused-function]
static int crb_pm_suspend(struct device *dev)
^
drivers/char/tpm/tpm_crb.c:551:12: warning: ‘crb_pm_resume’ defined but not
used [-Wunused-function]
static int crb_pm_resume(struct device *dev)
^
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However, this patch fixes this warning by using __maybe_unused on function
that are in the preprocessor condition.
Fixes: 848efcfb560c ("tpm/tpm_crb: enter the low power state upon device suspend") Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Nayna Jain [Fri, 10 Mar 2017 18:45:54 +0000 (13:45 -0500)]
tpm: add sleep only for retry in i2c_nuvoton_write_status()
Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.
This patch calls usleep_range() only if retry is to be done.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com> Cc: stable@vger.kernel.org (linux-4.8) Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Andy Shevchenko [Wed, 15 Mar 2017 19:58:00 +0000 (21:58 +0200)]
tpm/st33zp24: Add GPIO ACPI mapping table
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.
The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data. Attempting to get data before
the probe() caused the problem.
This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.
fixes: 9e0d39d8a6a0 ("tpm: Remove useless priv field in struct tpm_vendor_specific") Cc: <stable@vger.kernel.org> Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Jerry Snitselaar [Sat, 11 Mar 2017 00:46:04 +0000 (17:46 -0700)]
tpm_crb: check for bad response size
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.
Cc: stable@vger.kernel.org Fixes: 30fc8d138e912 ("tpm: TPM 2.0 CRB Interface") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
James Bottomley [Tue, 31 Jan 2017 23:47:31 +0000 (15:47 -0800)]
tpm2: add session handle context saving and restoring to the space code
Sessions are different from transient objects in that their handles
may not be virtualized (because they're used for some hmac
calculations). Additionally when a session is context saved, a
vestigial memory remains in the TPM and if it is also flushed, that
will be lost and the session context will refuse to load next time, so
the code is updated to flush only transient objects after a context
save. Add a separate array (chip->session_tbl) to save and restore
sessions by handle. Use the failure of a context save or load to
signal that the session has been flushed from the TPM and we can
remove its memory from chip->session_tbl.
Sessions are also isolated during each instance of a tpm space. This
means that spaces shouldn't be able to see each other's sessions and
is enforced by ensuring that a space user may only refer to sessions
handles that are present in their own chip->session_tbl. Finally when
a space is closed, all the sessions belonging to it should be flushed
so the handles may be re-used by other spaces.
Note that if we get a session save or load error, all sessions are
effectively flushed. Even though we restore the session buffer, all
the old sessions will refuse to load after the flush and they'll be
purged from our session memory. This means that while transient
context handling is still soft in the face of errors, session handling
is hard (any failure of the model means all sessions are lost).
Fixes-from: Colin Ian King <colin.king@canonical.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
James Bottomley [Tue, 3 Jan 2017 17:07:32 +0000 (09:07 -0800)]
tpm: expose spaces via a device link /dev/tpmrm<n>
Currently the tpm spaces are not exposed to userspace. Make this
exposure via a separate device, which can now be opened multiple times
because each read/write transaction goes separately via the space.
Concurrency is protected by the chip->tpm_mutex for each read/write
transaction separately. The TPM is cleared of all transient objects
by the time the mutex is dropped, so there should be no interference
between the kernel and userspace.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
James Bottomley [Wed, 11 Jan 2017 03:08:53 +0000 (19:08 -0800)]
tpm: split out tpm-dev.c into tpm-dev.c and tpm-common-dev.c
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Jarkko Sakkinen [Fri, 6 Jan 2017 12:03:45 +0000 (14:03 +0200)]
tpm: infrastructure for TPM spaces
Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.
The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.
When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:
1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
map resulting physical handle to virtual handle if there is such.
This commit does not implement virtualization support for hmac and
policy sessions.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jarkko Sakkinen [Fri, 11 Nov 2016 04:42:07 +0000 (20:42 -0800)]
tpm: validate TPM 2.0 commands
Check for every TPM 2.0 command that the command code is supported and
the command buffer has at least the length that can contain the header
and the handle area.
For ContextSave and FlushContext we mark the body to be part of the
handle area. This gives validation for these commands at zero
cost, including the body of the command.
The more important reason for this is that we can virtualize these
commands in the same way as you would virtualize the handle area of a
command.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jarkko Sakkinen [Sat, 26 Nov 2016 11:39:35 +0000 (13:39 +0200)]
tpm: export tpm2_flush_context_cmd
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jarkko Sakkinen [Tue, 14 Feb 2017 19:57:42 +0000 (21:57 +0200)]
tpm: move length validation to tpm_transmit()
Check that the length matches the length reported by the response
header already in tpm_transmit() to improve validation.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jarkko Sakkinen [Wed, 8 Feb 2017 11:11:36 +0000 (13:11 +0200)]
tpm_crb: encapsulate crb_wait_for_reg_32
Encapsulated crb_wait_for_reg32() so that state changes in other CRB
registers than TPM_CRB_CTRL_REQ_x can be waited.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Gang Wei <gang.wei@intel.com>
Jarkko Sakkinen [Wed, 8 Feb 2017 11:11:35 +0000 (13:11 +0200)]
tpm_crb: map locality registers
In order to provide access to locality registers, this commits adds
mapping of the head of the CRB registers, which are located right
before the control area.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Gang Wei <gang.wei@intel.com>
Peter Huewe [Thu, 2 Mar 2017 13:03:15 +0000 (13:03 +0000)]
tpm_tis_spi: Add small delay after last transfer
Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.
As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.
Cc: <stable@vger.kernel.org> Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Peter Huewe [Thu, 2 Mar 2017 13:03:14 +0000 (13:03 +0000)]
tpm_tis_spi: Remove limitation of transfers to MAX_SPI_FRAMESIZE bytes
Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.
v2: Moved scope of spi_message to the top as requested by Jarkko Cc: <stable@vger.kernel.org> Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Peter Huewe [Thu, 2 Mar 2017 13:03:13 +0000 (13:03 +0000)]
tpm_tis_spi: Check correct byte for wait state indicator
Wait states are signaled in the last byte received from the TPM in
response to the header, not the first byte. Check rx_buf[3] instead of
rx_buf[0].
Cc: <stable@vger.kernel.org> Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Peter Huewe [Thu, 2 Mar 2017 13:03:12 +0000 (13:03 +0000)]
tpm_tis_spi: Abort transfer when too many wait states are signaled
Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.
Cc: <stable@vger.kernel.org> Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Peter Huewe [Thu, 2 Mar 2017 13:03:11 +0000 (13:03 +0000)]
tpm_tis_spi: Use single function to transfer data
The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.
This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)
v2: u16 instead of u8 for the length. Cc: <stable@vger.kernel.org> Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Winkler, Tomas [Sun, 5 Mar 2017 23:53:35 +0000 (01:53 +0200)]
tpm/tpm_crb: enter the low power state upon device suspend
This fix enables a platform to enter the idle state (suspend-to-idle)
The driver needs to request explicitly go_idle upon completion
from the pm suspend handler.
The runtime pm is disabled on suspend during prepare state by calling
pm_runtime_get_noresume, hence we cannot relay on runtime pm to leave
the device in low power state. Symmetrically cmdReady is called
upon resume.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Siged-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Nayna Jain [Fri, 10 Mar 2017 18:45:53 +0000 (13:45 -0500)]
tpm: msleep() delays - replace with usleep_range() in i2c nuvoton driver
Commit 500462a9de65 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers. Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration. The only exception noted to this were
networking timers with a small expiry time.
Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay. The
non-cascading wheel delay is based on CONFIG_HZ. For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.
Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.
* HZ 1000 steps
* Level Offset Granularity Range
* 0 0 1 ms 0 ms - 63 ms
* 1 64 8 ms 64 ms - 511 ms
* 2 128 64 ms 512 ms - 4095 ms (512ms - ~4s)
* HZ 250
* Level Offset Granularity Range
* 0 0 4 ms 0 ms - 255 ms
* 1 64 32 ms 256 ms - 2047 ms (256ms - ~2s)
* 2 128 256 ms 2048 ms - 16383 ms (~2s - ~16s)
Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de65.
Jason Gunthorpe [Tue, 21 Feb 2017 21:14:24 +0000 (14:14 -0700)]
tpm crb: Work around BIOS's that report the wrong ACPI region size
The expectation is that the if the CRB cmd/rsp buffer falls within the
ACPI region that the entire buffer will be within the reason. Otherwise
resource reservation will fail when it crosses regions.
Work around this BIOS bug by limiting the cmd/rsp buffer to the length
of the declared ACPI region. BIOS vendors should fix this by making
the ACPI and register length declarations consistent.
Reported-by: Davide Guerri <davide.guerri@gmail.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Davide Guerri <davide.guerri@gmail.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_tis_core: Choose appropriate timeout for reading burstcount
TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.
This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.
During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.
Cc: stable@vger.kernel.org Fixes: aec04cbdf723 ("tpm: TPM 2.0 FIFO Interface") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Elena Reshetova [Fri, 31 Mar 2017 12:20:49 +0000 (15:20 +0300)]
security, keys: convert key_user.usage from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Elena Reshetova [Fri, 31 Mar 2017 12:20:48 +0000 (15:20 +0300)]
security, keys: convert key.usage from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Kees Cook [Wed, 29 Mar 2017 23:52:58 +0000 (16:52 -0700)]
TOMOYO: Use designated initializers
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
Tetsuo Handa [Fri, 24 Mar 2017 11:46:33 +0000 (20:46 +0900)]
LSM: Revive security_task_alloc() hook and per "struct task_struct" security blob.
We switched from "struct task_struct"->security to "struct cred"->security
in Linux 2.6.29. But not all LSM modules were happy with that change.
TOMOYO LSM module is an example which want to use per "struct task_struct"
security blob, for TOMOYO's security context is defined based on "struct
task_struct" rather than "struct cred". AppArmor LSM module is another
example which want to use it, for AppArmor is currently abusing the cred
a little bit to store the change_hat and setexeccon info. Although
security_task_free() hook was revived in Linux 3.4 because Yama LSM module
wanted to release per "struct task_struct" security blob,
security_task_alloc() hook and "struct task_struct"->security field were
not revived. Nowadays, we are getting proposals of lightweight LSM modules
which want to use per "struct task_struct" security blob.
We are already allowing multiple concurrent LSM modules (up to one fully
armored module which uses "struct cred"->security field or exclusive hooks
like security_xfrm_state_pol_flow_match(), plus unlimited number of
lightweight modules which do not use "struct cred"->security nor exclusive
hooks) as long as they are built into the kernel. But this patch does not
implement variable length "struct task_struct"->security field which will
become needed when multiple LSM modules want to use "struct task_struct"->
security field. Although it won't be difficult to implement variable length
"struct task_struct"->security field, let's think about it after we merged
this patch.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: John Johansen <john.johansen@canonical.com> Acked-by: Serge Hallyn <serge@hallyn.com> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Tested-by: Djalal Harouni <tixxdz@gmail.com> Acked-by: José Bollo <jobol@nonadev.net> Cc: Paul Moore <paul@paul-moore.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: Eric Paris <eparis@parisplace.org> Cc: Kees Cook <keescook@chromium.org> Cc: James Morris <james.l.morris@oracle.com> Cc: José Bollo <jobol@nonadev.net> Signed-off-by: James Morris <james.l.morris@oracle.com>
Linus Torvalds [Sun, 26 Mar 2017 18:15:54 +0000 (11:15 -0700)]
Merge tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"A smattering of different small fixes for some random driver
subsystems. Nothing all that major, just resolutions for reported
issues and bugs.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
extcon: int3496: Set the id pin to direction-input if necessary
extcon: int3496: Use gpiod_get instead of gpiod_get_index
extcon: int3496: Add dependency on X86 as it's Intel specific
extcon: int3496: Add GPIO ACPI mapping table
extcon: int3496: Rename GPIO pins in accordance with binding
vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
ppdev: fix registering same device name
parport: fix attempt to write duplicate procfiles
auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
Drivers: hv: vmbus: Don't leak channel ids
Drivers: hv: util: don't forget to init host_ts.lock
Drivers: hv: util: move waiting for release to hv_utils_transport itself
vmbus: remove hv_event_tasklet_disable/enable
vmbus: use rcu for per-cpu channel list
mei: don't wait for os version message reply
mei: fix deadlock on mei reset
intel_th: pci: Add Gemini Lake support
intel_th: pci: Add Denverton SOC support
intel_th: Don't leak module refcount on failure to activate
...
Linus Torvalds [Sun, 26 Mar 2017 18:05:42 +0000 (11:05 -0700)]
Merge tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single kernfs fix for 4.11-rc4 that resolves a reported
issue.
It has been in linux-next with no reported issues"
* tag 'driver-core-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: Check KERNFS_HAS_RELEASE before calling kernfs_release_file()
Linus Torvalds [Sun, 26 Mar 2017 18:03:42 +0000 (11:03 -0700)]
Merge tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.11-rc4.
One of these fix a long-standing issue in the ldisc code that was
found by Dmitry Vyukov with his great fuzzing work. The other fixes
resolve other reported issues, and there is one revert of a patch in
4.11-rc1 that wasn't correct.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix data race in tty_ldisc_ref_wait()
tty: don't panic on OOM in tty_set_ldisc()
Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
serial: 8250_dw: Fix breakage when HAVE_CLK=n
serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios
Linus Torvalds [Sun, 26 Mar 2017 18:02:00 +0000 (11:02 -0700)]
Merge tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes for 4.11-rc4 that resolve a
number of tiny reported issues. All of these have been in linux-next
for a while with no reported issues"
* tag 'staging-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: imu: st_lsm6dsx: fix FIFO_CTRL2 overwrite during watermark configuration
iio: adc: ti_am335x_adc: fix fifo overrun recovery
iio: sw-device: Fix config group initialization
iio: magnetometer: ak8974: remove incorrect __exit markups
iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3
Linus Torvalds [Sun, 26 Mar 2017 17:52:52 +0000 (10:52 -0700)]
Merge tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of
good fixes from Johan for devices with crazy descriptors. There are a
few new device ids in here as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
usb: gadget: udc: remove pointer dereference after free
usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
usb: gadget: acm: fix endianness in notifications
usb: dwc3: gadget: delay unmap of bounced requests
USB: serial: qcserial: add Dell DW5811e
usb: hub: Fix crash after failure to read BOS descriptor
ACM gadget: fix endianness in notifications
USB: usbtmc: fix probe error path
USB: usbtmc: add missing endpoint sanity check
USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
usb: musb: fix possible spinlock deadlock
usb: musb: dsps: fix iounmap in error and exit paths
usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
uwb: i1480-dfu: fix NULL-deref at probe
uwb: hwa-rc: fix NULL-deref at probe
USB: wusbcore: fix NULL-deref at probe
USB: uss720: fix NULL-deref at probe
...
Linus Torvalds [Sun, 26 Mar 2017 17:34:10 +0000 (10:34 -0700)]
Merge tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"These are all pretty minor. The fix for idle wakeup would be a bad bug
but has not been observed in practice.
The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
OK'ed it going via powerpc and I didn't hear from Jon.
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
Jain"
* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
gcc-plugins: update architecture list in documentation
Revert "powerpc/64: Disable use of radix under a hypervisor"
powerpc/64s: Fix idle wakeup potential to clobber registers
cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
Linus Torvalds [Sun, 26 Mar 2017 17:29:21 +0000 (10:29 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a memory leak on an error path, and two races when modifying
inodes relating to the inline_data and metadata checksum features"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix two spelling nits
ext4: lock the xattr block before checksuming it
jbd2: don't leak memory if setting up journal fails
ext4: mark inode dirty after converting inline directory
Linus Torvalds [Sat, 25 Mar 2017 22:36:56 +0000 (15:36 -0700)]
Merge tag 'fscrypt-for-linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypto fixes from Ted Ts'o:
"A code cleanup and bugfix for fs/crypto"
* tag 'fscrypt-for-linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: eliminate ->prepare_context() operation
fscrypt: remove broken support for detecting keyring key revocation
Linus Torvalds [Sat, 25 Mar 2017 22:31:50 +0000 (15:31 -0700)]
Merge tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- bug fixes in asus_atk0110, it87 and max31790 drivers
- added missing API definition to hwmon core
* tag 'hwmon-for-linus-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus_atk0110) fix uninitialized data access
hwmon: Add missing HWMON_T_ALARM
hwmon: (it87) Avoid registering the same chip on both SIO addresses
hwmon: (max31790) Set correct PWM value
Linus Torvalds [Sat, 25 Mar 2017 22:25:58 +0000 (15:25 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This has been a slow -rc cycle for the RDMA subsystem. We really
haven't had a lot of rc fixes come in. This pull request is the first
of this entire rc cycle and it has all of the suitable fixes so far
and it's still only about 20 patches. The fix for the minor breakage
cause by the dma mapping patchset is in here, as well as a couple
other potential oops fixes, but the rest is more minor.
Summary:
- fix for dma_ops change in this kernel, resolving the s390, powerpc,
and IOMMU operation
- a few other oops fixes
- the rest are all minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/qib: fix false-postive maybe-uninitialized warning
RDMA/iser: Fix possible mr leak on device removal event
IB/device: Convert ib-comp-wq to be CPU-bound
IB/cq: Don't process more than the given budget
IB/rxe: increment msn only when completing a request
uapi: fix rdma/mlx5-abi.h userspace compilation errors
IB/core: Restore I/O MMU, s390 and powerpc support
IB/rxe: Update documentation link
RDMA/ocrdma: fix a type issue in ocrdma_put_pd_num()
IB/rxe: double free on error
RDMA/vmw_pvrdma: Activate device on ethernet link up
RDMA/vmw_pvrdma: Dont hardcode QP header page
RDMA/vmw_pvrdma: Cleanup unused variables
infiniband: Fix alignment of mmap cookies to support VIPT caching
IB/core: Protect against self-requeue of a cq work item
i40iw: Receive netdev events post INET_NOTIFIER state
Linus Torvalds [Sat, 25 Mar 2017 22:13:55 +0000 (15:13 -0700)]
Merge branch 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit
Pull audit fix from Paul Moore:
"We've got an audit fix, and unfortunately it is big.
While I'm not excited that we need to be sending you something this
large during the -rcX phase, it does fix some very real, and very
tangled, problems relating to locking, backlog queues, and the audit
daemon connection.
This code has passed our testsuite without problem and it has held up
to my ad-hoc stress tests (arguably better than the existing code),
please consider pulling this as fix for the next v4.11-rcX tag"
* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
audit: fix auditd/kernel connection state tracking
Linus Torvalds [Sat, 25 Mar 2017 17:34:56 +0000 (10:34 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of Sunxi and Rockchip clk driver fixes and a core framework
one where we need to copy a string because we can't guarantee it isn't
freed sometime later"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: rockchip: Make uartpll a child of the gpll on rk3036
clk: rockchip: add "," to mux_pll_src_apll_dpll_gpll_usb480m_p on rk3036
clk: core: Copy connection id
dt-bindings: arm: update Armada CP110 system controller binding
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
aarch64-linux-gcc-7 complains about code it doesn't fully understand:
drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change':
include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is right, and despite trying hard, I could not come up with a version
that I liked better than just adding a fake initialization here to shut up the
warning.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg [Mon, 27 Feb 2017 18:16:33 +0000 (20:16 +0200)]
RDMA/iser: Fix possible mr leak on device removal event
When the rdma device is removed, we must cleanup all
the rdma resources within the DEVICE_REMOVAL event
handler to let the device teardown gracefully. When
this happens with live I/O, some memory regions are
occupied. Thus, track them too and dereg all the mr's.
We are safe with mr access by iscsi_iser_cleanup_task.
Reported-by: Raju Rangoju <rajur@chelsio.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg [Wed, 8 Mar 2017 20:03:17 +0000 (22:03 +0200)]
IB/device: Convert ib-comp-wq to be CPU-bound
This workqueue is used by our storage target mode ULPs
via the new CQ API. Recent observations when working
with very high-end flash storage devices reveal that
UNBOUND workqueue threads can migrate between cpu cores
and even numa nodes (although some numa locality is accounted
for).
While this attribute can be useful in some workloads,
it does not fit in very nicely with the normal
run-to-completion model we usually use in our target-mode
ULPs and the block-mq irq<->cpu affinity facilities.
The whole block-mq concept is that the completion will
land on the same cpu where the submission was performed.
The fact that our submitter thread is migrating cpus
can break this locality.
We assume that as a target mode ULP, we will serve multiple
initiators/clients and we can spread the load enough without
having to use unbound kworkers.
Also, while we're at it, expose this workqueue via sysfs which
is harmless and can be useful for debug.
David Marchand [Fri, 24 Feb 2017 14:38:26 +0000 (15:38 +0100)]
IB/rxe: increment msn only when completing a request
According to C9-147, MSN should only be incremented when the last packet of
a multi packet request has been received.
"Logically, the requester associates a sequential Send Sequence Number
(SSN) with each WQE posted to the send queue. The SSN bears a one-
to-one relationship to the MSN returned by the responder in each re-
sponse packet. Therefore, when the requester receives a response, it in-
terprets the MSN as representing the SSN of the most recent request
completed by the responder to determine which send WQE(s) can be
completed."
Fixes: 8700e3e7c485 ("Soft RoCE driver") Signed-off-by: David Marchand <david.marchand@6wind.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Bart Van Assche [Tue, 7 Mar 2017 22:56:53 +0000 (22:56 +0000)]
IB/core: Restore I/O MMU, s390 and powerpc support
Avoid that the following error message is reported on the console
while loading an RDMA driver with I/O MMU support enabled:
DMAR: Allocating domain for mlx5_0 failed
Ensure that DMA mapping operations that use to_pci_dev() to
access to struct pci_dev see the correct PCI device. E.g. the s390
and powerpc DMA mapping operations use to_pci_dev() even with I/O
MMU support disabled.
This patch preserves the following changes of the DMA mapping updates
patch series:
- Introduction of dma_virt_ops.
- Removal of ib_device.dma_ops.
- Removal of struct ib_dma_mapping_ops.
- Removal of an if-statement from each ib_dma_*() operation.
- IB HW drivers no longer set dma_device directly.
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reported-by: Parav Pandit <parav@mellanox.com> Fixes: commit 99db9494035f ("IB/core: Remove ib_device.dma_device") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: parav@mellanox.com Tested-by: parav@mellanox.com Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Leon Romanovsky [Tue, 28 Feb 2017 19:42:53 +0000 (21:42 +0200)]
IB/rxe: Update documentation link
All Soft-RoCE (rxe) is handled now in rdma-core user space library,
so the documentation. The patch below updates the documentation
link to that new location.
Reported-by: Josh Beavers <josh.beavers@gmail.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Linus Torvalds [Fri, 24 Mar 2017 21:37:12 +0000 (14:37 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes for the current series that should go into -rc4. This
contains:
- a fix for a potential corruption of un-started requests from Ming.
- a blk-stat fix from Omar, ensuring we flush the stat batch before
checking nr_samples.
- a set of fixes from Sagi for the nvmeof family"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: don't complete un-started request in timeout handler
nvme-loop: handle cpu unplug when re-establishing the controller
nvme-rdma: handle cpu unplug when re-establishing the controller
nvmet-rdma: Fix a possible uninitialized variable dereference
nvmet: confirm sq percpu has scheduled and switched to atomic
nvme-loop: fix a possible use-after-free when destroying the admin queue
blk-stat: fix blk_stat_sum() if all samples are batched
Linus Torvalds [Fri, 24 Mar 2017 21:32:21 +0000 (14:32 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- a couple of OMAP 4.11 regression fixes, including a boot regression
for SmartReflex, hypervisor mode in thumb2 mode, and reference
counting of device nodes
- a fix for cpu_idle on at91
- minor DT fixes on across several platforms: sunxi, bcm53xx, at91,
nsp, ns2, ux500, omap
- a fix to correct an API change in the reset controllers
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: dts: NS2: Add dma-coherent to relevant DT entries
reset: fix optional reset_control_get stubs to return NULL
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: dts: NSP: GPIO reboot open-source
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
ARM: dts: add the AB8500 clocks to the device tree
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
ARM: sun8i: Fix the mali clock rate
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
...
Linus Torvalds [Fri, 24 Mar 2017 21:29:23 +0000 (14:29 -0700)]
Merge tag 'for-linus-4.11b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Fixes for PM under Xen"
* tag 'for-linus-4.11b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/acpi: upload PM state from init-domain to Xen
xen/acpi: Replace hard coded "ACPI0007"
Linus Torvalds [Fri, 24 Mar 2017 21:21:09 +0000 (14:21 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"There's a kaslr fix and then two patches to update our native and
compat syscall tables. Arnd asked that we take the addition of statx
to the asm-generic unistd.h via arm64, as he didn't have anything
queued in the asm-generic tree.
Summary:
- Fix mapping of kernel image under certain kaslr offsets
- Hook up new statx syscall in asm-generic syscall table
- Update compat syscall table to match arch/arm/ (pkeys and statx)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kaslr: Fix up the kernel image alignment
arm64: compat: Update compat syscalls
generic syscalls: Wire up statx syscall
Jason Gunthorpe [Fri, 10 Mar 2017 18:34:20 +0000 (11:34 -0700)]
infiniband: Fix alignment of mmap cookies to support VIPT caching
When vmalloc_user is used to create memory that is supposed to be mmap'd
to user space, it is necessary for the mmap cookie (eg the offset) to be
aligned to SHMLBA.
This creates a situation where all virtual mappings of the same physical
page share the same virtual cache index and guarantees VIPT coherence.
Otherwise the cache is non-coherent and the kernel will not see writes
by userspace when reading the shared page (or vice-versa).
Linus Torvalds [Fri, 24 Mar 2017 20:42:17 +0000 (13:42 -0700)]
Merge tag 'iommu-fixes-v4.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few fixes piled up:
- fix a NULL-ptr dereference that happens in VT-d on some platforms
- a fix for ARM MSI region reporting, so that a sane interface makes
it to a released kernel
- fixes for leaf-checking in ARM io-page-table code
- two fixes for IO/TLB flushing code on ARM Exynos platforms"
* tag 'iommu-fixes-v4.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Disambiguate MSI region types
iommu/exynos: Workaround FLPD cache flush issues for SYSMMU v5
iommu/exynos: Block SYSMMU while invalidating FLPD cache
iommu/vt-d: Fix NULL pointer dereference in device_to_iommu
iommu/io-pgtable-arm-v7s: Check for leaf entry before dereferencing it
iommu/io-pgtable-arm: Check for leaf entry before dereferencing it
Sagi Grimberg [Wed, 8 Mar 2017 20:00:52 +0000 (22:00 +0200)]
IB/core: Protect against self-requeue of a cq work item
We need to make sure that the cq work item does not
run when we are destroying the cq. Unlike flush_work,
cancel_work_sync protects against self-requeue of the
work item (which we can do in ib_cq_poll_work).
Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>-- Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Linus Torvalds [Fri, 24 Mar 2017 20:37:40 +0000 (13:37 -0700)]
Merge tag 'mmc-v4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull mmc fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.11 rc4.
MMC core:
- Fix initialization of HS400-ES eMMC cards
- A couple of fixes for the mmc block device driver
- Resolved a compiler warning
MMC host:
- sdhci: Do not disable IRQs while waiting for clock
- sdhci-pci: Do not disable IRQs in sdhci_intel_set_power
- sdhci-of-arasan: Fix incorrect timeout clock
- mediatek: Fix bug for setting wrong clock frequency
- sdhci-of-at91: Use regulator to fix cmd timeout errors
- ushc: Fix NULL-deref at probe
- rockchip-dw-mshc: Rename RK1108 to RV1108 in DT"
* tag 'mmc-v4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci: Do not disable interrupts in sdhci_intel_set_power
mmc: sdhci: Do not disable interrupts while waiting for clock
mmc: ushc: fix NULL-deref at probe
mmc: sdhci-of-at91: Support external regulators
mmc: core: mmc_blk_rw_cmd_err - remove unused variable
mmc: mediatek: Fixed bug where clock frequency could be set wrong
mmc: block: Fix cmd error reset failure path
mmc: block: Fix is_waiting_last_req set incorrectly
mmc: core: Fix access to HS400-ES devices
mmc: sdhci-of-arasan: fix incorrect timeout clock
dt-bindings: rockchip-dw-mshc: rename RK1108 to RV1108
Linus Torvalds [Fri, 24 Mar 2017 20:34:16 +0000 (13:34 -0700)]
Merge tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-usb-firmware: don't do DMA on stack
- coda/imx-vdoa: platform_driver should not be const
- bdisp: Clean up file handle in open() error path
- exynos-gsc: Do not swap cb/cr for semi planar formats
* tag 'media/v4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] exynos-gsc: Do not swap cb/cr for semi planar formats
[media] bdisp: Clean up file handle in open() error path
[media] coda/imx-vdoa: platform_driver should not be const
[media] dvb-usb-firmware: don't do DMA on stack
Shiraz Saleem [Fri, 17 Mar 2017 23:30:07 +0000 (18:30 -0500)]
i40iw: Receive netdev events post INET_NOTIFIER state
Netdev notification events are de-registered only when all
client iwdev instances are removed. If a single client is closed
and re-opened, netdev events could arrive even before the Control
Queue-Pair (CQP) is created, causing a NULL pointer dereference crash
in i40iw_get_cqp_request. Fix this by allowing netdev event
notification only after we have reached the INET_NOTIFIER state with
respect to device initialization.
Linus Torvalds [Fri, 24 Mar 2017 20:15:52 +0000 (13:15 -0700)]
Merge tag 'drm-fixes-for-v4.11-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
- one core drm/fbdev regression fix
- a set of i915 fixes including a few GVT related fixes, along with
some reset fixes
- one new PCI id for amdgpu, and some minor workaround regression
fixes
- .. and a set of exynos fixes, dropping support for an old unsupported
SoC, some vblank timing fixes, and an info leak fix
* tag 'drm-fixes-for-v4.11-rc4' of git://people.freedesktop.org/~airlied/linux: (34 commits)
drm/fb-helper: Allow var->x/yres(_virtual) < fb->width/height again
drm/i915: make context status notifier head be per engine
drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)
drm/exynos/dsi: make te-gpios optional
drm/exynos: Print kernel pointers in a restricted form
drm/exynos/decon5433: fix software trigger mask
drm/exynos/fimd: signal frame done interrupt at front porch
drm/exynos/decon5433: signal frame done interrupt at front porch
drm/exynos/decon5433: fix vblank event handling
drm/exynos: move crtc event handling to drivers callbacks
drm/exynos: Remove support for Exynos4415 (SoC not supported anymore)
drm/exynos/decon5433: & vs | typo
drm/amd/amdgpu: add POLARIS12 PCI ID
drm/i915/gvt: Fix gvt scheduler interval time
drm/i915/gvt: GVT pin/unpin shadow context
drm/i915/gvt: scan shadow indirect context image when valid
drm/i915/kvmgt: fix suspicious rcu dereference usage
drm/i915/gvt: add enable_execlists check before enable gvt
drm/i915/gvt: Remove bogus retry around i915_wait_request
drm/i915/gvt: correct the ggtt valid bit check in pipe control command
...
Arnd Bergmann [Fri, 24 Mar 2017 16:51:50 +0000 (17:51 +0100)]
Merge tag 'arm-soc/for-4.11/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm64 Device Tree fixes for 4.11" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon adds missing "dma-coherent" property to the Northstar 2 DTS include file
in order to fix both performance and cache problems for: PCIe, Ethernet,
PDC/mailbox, SATA3 and SDHCI
* tag 'arm-soc/for-4.11/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: NS2: Add dma-coherent to relevant DT entries
Linus Torvalds [Fri, 24 Mar 2017 03:00:39 +0000 (20:00 -0700)]
Merge tag 'pm-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"One of these is an intel_pstate regression fix and it is not a small
change, but it mostly removes code that shouldn't be there. That code
was acquired by mistake and has been a source of constant pain since
then, so the time has come to get rid of it finally. We have not seen
problems with this change in the lab, so fingers crossed.
The rest is more usual: one more intel_pstate commit removing useless
code, a cpufreq core fix to make it restore policy limits on CPU
online (which prevents the limits from being reset over system
suspend/resume), a schedutil cpufreq governor initialization fix to
make it actually work as advertised on all systems and an extra sanity
check in the cpuidle core to prevent crashes from happening if the
arch code messes things up.
Specifics:
- Make intel_pstate use one set of global P-state limits in the
active mode regardless of the scaling_governor settings for
individual CPUs instead of switching back and forth between two of
them in a way that is hard to control (Rafael Wysocki).
- Drop a useless function from intel_pstate to prevent it from
modifying the maximum supported frequency value unexpectedly which
may confuse the cpufreq core (Rafael Wysocki).
- Fix the cpufreq core to restore policy limits on CPU online so that
the limits are not reset over system suspend/resume, among other
things (Viresh Kumar).
- Fix the initialization of the schedutil cpufreq governor to make
the IO-wait boosting mechanism in it actually work on systems with
one CPU per cpufreq policy (Rafael Wysocki).
- Add a sanity check to the cpuidle core to prevent crashes from
happening if the architecture code initialization fails to set up
things as expected (Vaidyanathan Srinivasan)"
* tag 'pm-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Restore policy min/max limits on CPU online
cpuidle: Validate cpu_dev in cpuidle_add_sysfs()
cpufreq: intel_pstate: Fix policy data management in passive mode
cpufreq: schedutil: Fix per-CPU structure initialization in sugov_start()
cpufreq: intel_pstate: One set of global limits in active mode
Linus Torvalds [Fri, 24 Mar 2017 02:51:06 +0000 (19:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Fixes to various USB drivers to validate existence of endpoints before
trying to use them, fixes to APLS v8 protocol, and a couple of i8042
quirks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ALPS - fix trackstick button handling on V8 devices
Input: ALPS - fix V8+ protocol handling (73 03 28)
Input: sur40 - validate number of endpoints before using them
Input: kbtab - validate number of endpoints before using them
Input: hanwang - validate number of endpoints before using them
Input: yealink - validate number of endpoints before using them
Input: ims-pcu - validate number of endpoints before using them
Input: cm109 - validate number of endpoints before using them
Input: iforce - validate number of endpoints before using them
Input: elan_i2c - add ASUS EeeBook X205TA special touchpad fw
Input: i8042 - add TUXEDO BU1406 (N24_25BU) to the nomux list
Input: synaptics-rmi4 - prevent null pointer dereference in f30
Input: i8042 - add noloop quirk for Dell Embedded Box PC 3000
Dave Airlie [Fri, 24 Mar 2017 01:04:08 +0000 (11:04 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Just several fixups,
- fix page fault and vblank timeout issues due to delayed vblank handling.
- fix panel driver probing to fail without te-gpios property.
- fix potential security hole by using "%pK" format.
- fix wrong if statement condition.
And one cleanup which removes Exynos4415 SoC support which is not supported
anymore.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/dsi: make te-gpios optional
drm/exynos: Print kernel pointers in a restricted form
drm/exynos/decon5433: fix software trigger mask
drm/exynos/fimd: signal frame done interrupt at front porch
drm/exynos/decon5433: signal frame done interrupt at front porch
drm/exynos/decon5433: fix vblank event handling
drm/exynos: move crtc event handling to drivers callbacks
drm/exynos: Remove support for Exynos4415 (SoC not supported anymore)
drm/exynos/decon5433: & vs | typo
Stephen Boyd [Thu, 23 Mar 2017 23:08:46 +0000 (16:08 -0700)]
Merge tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
A few fixes for a bunch of clocks on a few SoCs. The most important one is
probably one that fixes the NKMP clock frequency calculation and could end
up with clocking the CPU frequency to out of bounds rates.
* tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
Merge tag 'fixes-for-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.11-rc4
f_acm got an endianness fix by Oliver Neukum. This has been around for a
long time but it's finally fixed.
f_hid learned that it should never access hidg->req without first
grabbing the spinlock.
Roger Quadros fixed two bugs in the f_uvc function driver.
Janusz Dziedzic fixed a very peculiar bug with EP0, one that's rather
difficult to trigger. When we're dealing with bounced EP0 requests, we
should delay unmap until after ->complete() is called.
Merge tag 'phy-for-4.11-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.11-rc
*) Revert USB3 PHY support for Broadcom NSP SoC
*) Fix compiler error on qcom-usb-hs when depends on EXTCON
is not added
*) Fix error handling in phy-exynos-pcie
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Arnd Bergmann [Thu, 23 Mar 2017 15:03:11 +0000 (16:03 +0100)]
hwmon: (asus_atk0110) fix uninitialized data access
The latest gcc-7 snapshot adds a warning to point out that when
atk_read_value_old or atk_read_value_new fails, we copy
uninitialized data into sensor->cached_value:
drivers/hwmon/asus_atk0110.c: In function 'atk_input_show':
drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Adding an error check avoids this. All versions of the driver
are affected.
Linus Torvalds [Thu, 23 Mar 2017 18:58:08 +0000 (11:58 -0700)]
Merge tag 'sound-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains the collection of small fixes for 4.11 that were pending
during my vacation:
- a few HD-audio quirks (more Dell headset support, docking station
support on HP laptops)
- a regression fix for the previous ctxfi DMA mask fix
- a correction of the new CONFIG_SND_X86 menu entry
- a fix for the races in ALSA sequencer core spotted by syzkaller"
* tag 'sound-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Adding a group of pin definition to fix headset problem
ALSA: seq: Fix racy cell insertions during snd_seq_pool_done()
ALSA: x86: Make CONFIG_SND_X86 bool
ALSA: hda - add support for docking station for HP 840 G3
ALSA: hda - add support for docking station for HP 820 G2
ALSA: ctxfi: Fix the incorrect check of dma_set_mask() call
Linus Torvalds [Thu, 23 Mar 2017 18:39:33 +0000 (11:39 -0700)]
Merge branch 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Zygo tracked down a very old bug with inline compressed extents.
I didn't tag this one for stable because I want to do individual
tested backports. It's a little tricky and I'd rather do some extra
testing on it along the way"
* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: add missing memset while reading compressed inline extents
Btrfs: fix regression in lock_delalloc_pages
btrfs: remove btrfs_err_str function from uapi/linux/btrfs.h
1) Several netfilter fixes from Pablo and the crew:
- Handle fragmented packets properly in netfilter conntrack, from
Florian Westphal.
- Fix SCTP ICMP packet handling, from Ying Xue.
- Fix big-endian bug in nftables, from Liping Zhang.
- Fix alignment of fake conntrack entry, from Steven Rostedt.
2) Fix feature flags setting in fjes driver, from Taku Izumi.
3) Openvswitch ipv6 tunnel source address not set properly, from Or
Gerlitz.
4) Fix jumbo MTU handling in amd-xgbe driver, from Thomas Lendacky.
5) sk->sk_frag.page not released properly in some cases, from Eric
Dumazet.
6) Fix RTNL deadlocks in nl80211, from Johannes Berg.
7) Fix erroneous RTNL lockdep splat in crypto, from Herbert Xu.
8) Cure improper inflight handling during AF_UNIX GC, from Andrey
Ulanov.
9) sch_dsmark doesn't write to packet headers properly, from Eric
Dumazet.
10) Fix SCM_TIMESTAMPING_OPT_STATS handling in TCP, from Soheil Hassas
Yeganeh.
11) Add some IDs for Motorola qmi_wwan chips, from Tony Lindgren.
12) Fix nametbl deadlock in tipc, from Ying Xue.
13) GRO and LRO packets not counted correctly in mlx5 driver, from Gal
Pressman.
14) Fix reset of internal PHYs in bcmgenet, from Doug Berger.
15) Fix hashmap allocation handling, from Alexei Starovoitov.
16) nl_fib_input() needs stronger netlink message length checking, from
Eric Dumazet.
17) Fix double-free of sk->sk_filter during sock clone, from Daniel
Borkmann.
18) Fix RX checksum offloading in aquantia driver, from Pavel Belous.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
net:ethernet:aquantia: Fix for RX checksum offload.
amd-xgbe: Fix the ECC-related bit position definitions
sfc: cleanup a condition in efx_udp_tunnel_del()
Bluetooth: btqcomsmd: fix compile-test dependency
inet: frag: release spinlock before calling icmp_send()
tcp: initialize icsk_ack.lrcvtime at session start time
genetlink: fix counting regression on ctrl_dumpfamily()
socket, bpf: fix sk_filter use after free in sk_clone_lock
ipv4: provide stronger user input validation in nl_fib_input()
bpf: fix hashmap extra_elems logic
enic: update enic maintainers
net: bcmgenet: remove bcmgenet_internal_phy_setup()
ipv6: make sure to initialize sockc.tsflags before first use
fjes: Do not load fjes driver if extended socket device is not power on.
fjes: Do not load fjes driver if system does not have extended socket device.
net/mlx5e: Count LRO packets correctly
net/mlx5e: Count GSO packets correctly
net/mlx5: Increase number of max QPs in default profile
net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps
net/mlx5e: Use the proper UAPI values when offloading TC vlan actions
...
Ankur Arora [Tue, 21 Mar 2017 22:43:38 +0000 (15:43 -0700)]
xen/acpi: upload PM state from init-domain to Xen
This was broken in commit cd979883b9ed ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)
The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: stable@vger.kernel.org Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Michel Dänzer [Thu, 23 Mar 2017 08:53:26 +0000 (17:53 +0900)]
drm/fb-helper: Allow var->x/yres(_virtual) < fb->width/height again
Otherwise this can also prevent modesets e.g. for switching VTs, when
multiple monitors with different native resolutions are connected.
The depths must match though, so keep the != test for that.
Also update the DRM_DEBUG output to be slightly more accurate, this
doesn't only affect requests from userspace.
Bugzilla: https://bugs.freedesktop.org/99841 Fixes: 865afb11949e ("drm/fb-helper: reject any changes to the fbdev") Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Daniel Stone <daniels@collabora.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170323085326.20185-1-michel@daenzer.net
Hui Wang [Thu, 23 Mar 2017 02:00:25 +0000 (10:00 +0800)]
ALSA: hda - Adding a group of pin definition to fix headset problem
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
Signed-off-by: Hui Wang <hui.wang@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adrian Hunter [Mon, 20 Mar 2017 17:50:30 +0000 (19:50 +0200)]
mmc: sdhci-pci: Do not disable interrupts in sdhci_intel_set_power
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Adrian Hunter [Mon, 20 Mar 2017 17:50:29 +0000 (19:50 +0200)]
mmc: sdhci: Do not disable interrupts while waiting for clock
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Lendacky, Thomas [Wed, 22 Mar 2017 22:25:27 +0000 (17:25 -0500)]
amd-xgbe: Fix the ECC-related bit position definitions
The ECC bit positions that describe whether the ECC interrupt is for
Tx, Rx or descriptor memory and whether the it is a single correctable
or double detected error were defined in incorrectly (reversed order).
Fix the bit position definitions for these settings so that the proper
ECC handling is performed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 22 Mar 2017 09:10:02 +0000 (12:10 +0300)]
sfc: cleanup a condition in efx_udp_tunnel_del()
Presumably if there is an "add" function, there is also a "del"
function. But it causes a static checker warning because it looks like
a common cut and paste bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log