Simon Glass [Sun, 31 Jul 2016 23:35:03 +0000 (17:35 -0600)]
test: Check exit status in run_and_log_expect_exception()
This check was missed. Add it and make the message more verbose.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Tom Rini <trini@konsulko.com> Fixes: 9e17b034 (test/py: Provide a way to check that a command fails)
Alexander Graf [Sat, 30 Jul 2016 21:13:03 +0000 (23:13 +0200)]
armv8: mmu: Detect page table overflow in emergency pt creation
We create 2 sets of page tables: One for normal operation, one for
emergency (used while modifying the former).
Because the page tables grow dynamically, we have code that checks
for overflow. Unfortunately we didn't adjust the available space
variable while creating the emergency tables, so potentially someone
might run into an overflow there (not seen in real world yet though!).
Fix it by properly adjusting the size as well as the base offset in
emergency page table creation.
Reported-by: York Sun <york.sun@nxp.com> Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: York Sun <york.sun@nxp.com>
Kever Yang [Fri, 29 Jul 2016 03:12:18 +0000 (11:12 +0800)]
cmd: gpt: fix the wrong size parse for the last partition
The calculation of "dev_desc->lba - 34 - 1 - offset" is not correct for
size '-', because both fist_usable_lba and last_usable_lba will remain
34 sectors.
We can simply use 0 for size '-' because the part_efi module will decode
the size and auto extend the size to maximum available size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Thu, 28 Jul 2016 02:29:42 +0000 (22:29 -0400)]
omap3: Drop omap3_evm_quick_* targets
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Tom Rini [Thu, 28 Jul 2016 02:29:41 +0000 (22:29 -0400)]
omap3, omap4: Enable USE_TINY_PRINTF for all
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler. Move to USE_TINY_PRINTF
to give them more room. OMAP4 will soon enough be in a similar place,
so enable that now.
Max Filippov [Thu, 28 Jul 2016 00:57:24 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_std_bdinfo
print_std_bdinfo outputs typical set of board information entries:
boot params location, memory and flash addresses and sizes, network
interfaces information and configured serial baud rate.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:22 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_eth_ip_addr
print_eth_ip_addr outputs eth configurations for up to 6 interfaces and
configured IP address.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6d4 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6d4 ("types.h: move and redefine resource_size_t") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Ravi Babu <ravibabu@ti.com> Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
tools: moveconfig: support CONFIG_SYS_EXTRA_OPTIONS cleaning
We mostly move config options from board header files to Kconfig,
but sometimes config defines come from CONFIG_SYS_EXTRA_OPTIONS.
Historically, CONFIG_SYS_EXTRA_OPTIONS originates in boards.cfg,
which was used as a central database of configuration prior to the
Kconfig conversion.
Now, we want to migrate to primary entries in Kconfig rather than
option list in CONFIG_SYS_EXTRA_OPTIONS, so it should be helpful to
have the tool to cleanup CONFIG_SYS_EXTRA_OPTIONS automatically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
tools: moveconfig: show result of header cleaning in unified diff
The header cleanup feature of this tool now removes empty ifdef's,
successive blank lines as well as moved option defines. So, we
want to see a little more context to check which lines were deleted.
It is true that we can see it by "git diff", but it would not work
in the --dry-run mode. So, here, this commit.
tools: moveconfig: trim garbage lines after header cleanups
The tools/moveconfig.py has a feature to cleanup #define/#undef's
of moved config options, but I want this tool to do a better job.
For example, when we are moving CONFIG_FOO and its define is
surrounded by #ifdef ... #endif, like follows:
#ifdef CONFIG_BAR
# define CONFIG_FOO
#endif
The header cleanup will leave empty #ifdef ... #endif:
#ifdef CONFIG_BAR
#endif
Likewise, if a define line between two blank lines
<blank line>
#define CONFIG_FOO
<blank lines.
... is deleted, the result of the clean-up will be successive empty
lines, which is a coding-style violation.
It is tedious to remove left-over garbage lines manually, so I want
the tool to take care of this. The tool's job is still not perfect,
so we should check the output of the tool, but I hope our life will
be much easier with this patch.
Tom Rini [Fri, 22 Jul 2016 21:59:11 +0000 (17:59 -0400)]
ext4: Refuse to mount filesystems with 64bit feature set
With e2fsprogs after 1.43 the 64bit and metadata_csum features are
enabled by default. The metadata_csum feature changes how
ext4_group_desc->bg_checksum is calculated, which would break write
support. The 64bit feature however introduces changes such that it
cannot be read by implementations that do not support it. Since we do
not support this, we must not mount it.
Cc: Stephen Warren <swarren@nvidia.com> Cc: Simon Glass <sjg@chromium.org> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Stefan Roese <sr@denx.de> Reported-by: Andrew Bradford <andrew.bradford@kodakalaris.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 1 Aug 2016 22:54:53 +0000 (18:54 -0400)]
ARM: Rework and correct barrier definitions
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Sandy Patterson <apatterson@sightlogix.com> Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com> Reported-by: Sandy Patterson <apatterson@sightlogix.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Alexey Brodkin [Thu, 4 Aug 2016 12:00:35 +0000 (15:00 +0300)]
arc: Rename AXS101 board to more generic AXS10x
As of now we have 2 flavors of ARC SDP boards:
1) AXS101 - with ARC770 in ASIC
2) AXS103 - with ARC HS38 in FPGA
Both options share exactly the same base-board and only differ with
CPU-tiles in use. That means all peripherals are the same (they are
implemented in FPGA on the base-board) and so generic board could be
used for both.
While at it:
* Recreated defconfigs with savedefconfig
* In include/configs/axs10x.h numerical sizes replaced with
defines from linux/sizes.h for better readability.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Alexey Brodkin [Thu, 4 Aug 2016 11:35:01 +0000 (14:35 +0300)]
arc: Rename ARCangel4 board to nSIM
ARCangel was one of the main development boards back in the day but
now it's gone and replaced by other boards like ARC SDP.
But we also used to have simulation platform very similar to ARCangel4
in terms of CPU settings as well as basic IO like UART. Even though
ARCangel4 is long gone now we have a replacement for simulation which is
a plain or stand-alone nSIM and Free nSIM.
Note Free nSIM is available for download here:
https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
And while at it:
* Finally switch hex numerical values in nsim.h to defines from
include/linux/sizes.h
* Add defconfigs with ARC HS38 cores
* Recreated all defconfigs with savedefconfig
Alexey Brodkin [Wed, 3 Aug 2016 17:44:39 +0000 (20:44 +0300)]
arc: No need in sections defined in sources with newer tools
Starting from arc-2016.03 GNU tools linker properly works with
symbols defined in linker script and so external declarations
are no longer required, dump them.
Alexey Brodkin [Wed, 3 Aug 2016 17:45:22 +0000 (20:45 +0300)]
arc: Add debug messages during relocation fixups
This might be useful to make sure relocation fixups really
happen. And since this info gets printed only in DEBUG
build it doesn't really hurt normal execution.
ARMv8/fsl-ppa: Consolidate PPA image stored-media flag for XIP
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Appended the compatible strings of old version PSCI to the latest
version supported. And there are some psci functions' property must
be added to DT only for psci version 0.1, including cpu_on, cpu_off,
cpu_suspend, migrate.
Note, ARMv8 Secure Firmware Framework doesn't support PSCI ver 0.1.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Fri, 29 Jul 2016 16:02:29 +0000 (09:02 -0700)]
driver/ddr/fsl: Fix timing_cfg_2
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.
Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
Refresh cycle value must be selected based on the frequency
of DDR. tREFI = 7.8 us as per JEDEC. The value for MDREF[REF_CNT]
should be based on round up (tREFI/tCK) formula. For 500MHz, mdref
value should be 0x0f3c8000.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Enable DDR row-bank-column decoding to decode DDR address as
row-bank-column instead of bank-row-column for improving
performance of serial data transfers.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
crypto/fsl: Update blob cmd to accept 64bit addresses
Update blob cmd to accept 64bit source, key modifier and destination
addresses. Also correct output result print format for fsl specific
implementation of blob cmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Yunhui Cui [Wed, 13 Jul 2016 02:46:27 +0000 (10:46 +0800)]
driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Michal Simek [Mon, 1 Aug 2016 06:49:12 +0000 (08:49 +0200)]
ARM64: zynqmp: Do not enable DM_MMC by default
The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1: 329a449f2c289b4de8f892fca1d9379ce5fd81b8)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.
Move options to defconfig instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 29 Jul 2016 11:03:29 +0000 (13:03 +0200)]
ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.
Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1: 911954859d6dece49c3e4835faea004cfe392506)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:33:06 +0000 (20:33 -0600)]
buildman: Add a quick-start note
For those who just want to build a board, it is useful to see a quick hint
right at the start of the documentation. Add a few commands showing how to
download toolchains and build a board.
The current code for setting up the toolchain config always writes the new
paths to an item called 'toolchain'. This means that it will overwrite any
existing toolchain item with the same name. In practice, this means that:
buildman --fetch-arch all
will fetch all toolchains, but only the path of the final one will be added
to the config. This normally works out OK, since most toolchains are the
same version (e.g. gcc 4.9) and will be found on the same path. But it is
not correct and toolchains for archs which don't use the same version will
not function as expected.
Adjust the code to use a complete glob of the toolchain path.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:04 +0000 (20:33 -0600)]
buildman: Drop the toolchain error when downloading toolchains
It doesn't make sense to complain about missing toolchains when the
--fetch-arch option is being used. The user is presumably aware that there
is a toolchain problem and is actively correcting it by running with this
option.
Refactor the code to avoid printing this confusing message.
Simon Glass [Thu, 28 Jul 2016 02:33:02 +0000 (20:33 -0600)]
buildman: Improve the toolchain progress/error output
Use colour to make it easier to see what is going on. Also print a message
before downloading a new toolchain. Mention --fetch-arch in the message that
is shown when there are no available toolchains, since this is the quickest
way to resolve the problem.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:32:59 +0000 (20:32 -0600)]
buildman: Automatically create a config file if needed
If there is no ~/.buildman file, buildman currently complains and exists. To
make things a little more friendly, create an empty one automatically. This
will not allow things to be built, but --fetch-arch can be used to handle
that.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Michal Simek [Thu, 28 Jul 2016 07:06:41 +0000 (09:06 +0200)]
libfdt: Introduce new ARCH_FIXUP_FDT option
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where
U-Boot shouldn't update memory setup in DTB file.
One example of usage of this option is to boot OS with different memory
setup than U-Boot use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Fri, 29 Jul 2016 09:47:03 +0000 (11:47 +0200)]
sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SID
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,
This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.
Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 27 Jul 2016 15:58:06 +0000 (17:58 +0200)]
sunxi: Ensure that the NIC specific bytes of the mac are not all 0
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.
This commits adds a check to ensure this does not happen.
Cc: Chen-Yu Tsai <wens@csie.org> Cc: Corentin LABBE <clabbe.montjoie@gmail.com> Cc: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi: Hummingbird_A31_defconfig: Drop MACPWR option
MACPWR was used to bring the Ethernet PHY out of reset. The designware
driver now supports the phy reset gpio binding, so this is no longer
needed. In fact in requesting the same GPIO, it makes the designware
driver fail to probe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: gpio: Add .xlate function for gpio phandle resolution
sunxi uses a 2 cell phandle for gpio bindings. Also there are no
seperate nodes for each pin bank.
Add a custom .xlate function to map gpio phandles to the correct
pin bank device. This fixes gpio_request_by_name usage.
Fixes: 7aa974858422 ("dm: sunxi: Modify the GPIO driver to support driver
model") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
John Keeping [Mon, 25 Jul 2016 09:02:05 +0000 (10:02 +0100)]
rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers. In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.
Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed. The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch is style-related only, to reformat all the start.S code,
actually not following a coherent style inside single files and
between different cpu start.S files.
Linux format has been respected, as
- max line width at 80 columns
- one 8 cols tab between asm instructions and operands
- inline comments, where any, fixed at col 41
Vignesh R [Fri, 29 Jul 2016 08:52:30 +0000 (14:22 +0530)]
ARM: am57xx_evm: Enable QSPI support
AM571x IDK and AM572x IDK EVMs have spansion s25fl256s QSPI flash on the
board connected to TI QSPI IP over CS0. Therefore enable QSPI support.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Fri, 29 Jul 2016 08:52:31 +0000 (14:22 +0530)]
ARM: dts: am57xx-idk-common: Enable support for QSPI
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
AM437x SK and AM437x IDK EVMs have 64MB flash, therefore enable
CONFIG_SPI_FLASH_BAR to access flash regions above 16MB.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 25 Jul 2016 10:15:47 +0000 (15:45 +0530)]
ARM: dts: dra7xx: Update spi-max-frequency for QSPI
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:46 +0000 (15:45 +0530)]
configs: dra7xx: Update QSPI speed to 76.8MHz
Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:45 +0000 (15:45 +0530)]
spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
projects / karo-tx-uboot.git / log