Tomi Valkeinen [Thu, 26 Feb 2015 13:20:25 +0000 (15:20 +0200)]
drm/omap: only ignore DIGIT SYNC LOST for TV output
We need to ignore DIGIT SYNC LOST error when enabling/disabling TV
output. The code does that, but it ignores the DIGI SYNC LOST when
enabling any output. Normally this does no harm, but it could make us
miss DIGIT SYNC LOST on some rare occasions.
Fix the code to only ignore DIGIT SYNC LOST when enabling/disabling TV.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 26 Feb 2015 13:20:24 +0000 (15:20 +0200)]
drm/omap: fix race with error_irq
omapdrm tries to avoid error floods by unregistering the error irq when
an error happens, and then registering the error irq again later.
However, the code is racy, as it sometimes tries to unregister the error
irq when it's already unregistered, leading to WARN().
Also, the code only registers the error irq again when something is done
on that particular output, i.e. if only TV is used to flip the buffers,
and LCD is showing a same buffer, an error on LCD will cause the LCD
error irq to be unregistered and never registered again.
To fix this, let's keep the error irqs always enabled and trust the
DRM_ERROR_RATELIMITED to limit the flood.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 19 Nov 2014 10:50:13 +0000 (12:50 +0200)]
drm/omap: use DRM_ERROR_RATELIMITED() for error irqs
omapdrm uses normal DRM_ERROR() print when the HW reports an error. As
we sometimes may get a flood of errors, let's rather use
DRM_ERROR_RATELIMITED().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 14 Nov 2014 13:18:28 +0000 (15:18 +0200)]
drm/omap: stop connector polling during suspend
When not using proper hotplug detection, DRM polls periodically the
connectors to find out if a cable is connected. This polling can happen
at any time, even very late in the suspend process.
This causes a problem with omapdrm, when the poll happens during the
suspend process after GPIOs have been disabled, leading to a crash in
gpio_get().
This patch fixes the issue by adding suspend and resume hooks to
omapdrm, in which we disable and enable, respectively, the polling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 14 Nov 2014 13:18:27 +0000 (15:18 +0200)]
drm/omap: remove dummy PM functions
omapdrm has dummy functions for platform_device's
suspend/resume/shutdown. The functions don't do anything, and those
platform device functions are deprecated, so remove them from omapdrm.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Mon, 10 Nov 2014 10:23:01 +0000 (12:23 +0200)]
drm/omap: tiler: fix race condition with engine->async
The tiler irq handler uses engine->async value, but the code that sets
engine->async and enables the interrupt does not have a barrier. This
may cause the irq handler to see the old value of engine->async, causing
memory corruption.
Reported-by: Harinarayan Bhatta <harinarayan@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 3 Oct 2014 15:14:08 +0000 (15:14 +0000)]
drm/omap: fix plane's channel selection
omap_plane_pre_apply() sets the plane's output channel too late, only
after the plane has already been otherwise configured and enabled. This
causes problems, as at the configuration stage we need to make decisions
based on the output channel.
This may lead to bad plane settings or failing to setup the plane.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 25 Sep 2014 19:24:28 +0000 (19:24 +0000)]
drm/omap: handle incompatible buffer stride and pixel size
omapdrm doesn't check if the pitch of the framebuffer and the color
format's bits-per-pixel are compatible. omapdss requires that the stride
of a buffer is an integer number of pixels
For example, when using modetest with a display that has x resolution of
1280, and using packed 24 RGB mode (3 bytes per pixel), modetest
allocates a buffer with a byte stride of 4 * 1280 = 5120. But 5120 / 3 =
1706.666... pixels, which causes wrong colors and a tilt on the screen.
Add a check into omapdrm to return an error if the user tries to use
such a combination.
Note: this is not a HW requirement at least for non-rotation use cases,
but a SW driver requirement. In the future we should study if also
rotation use cases are fine with any stride size, and if so, change the
driver to allow these strides.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Thu, 25 Sep 2014 19:24:27 +0000 (19:24 +0000)]
drm/omap: fix error handling in omap_framebuffer_create()
When an error happens in omap_framebuffer_create(),
omap_framebuffer_create() calls omap_framebuffer_destroy() if the fb
struct has been allocated. However, that crashes, as
omap_framebuffer_destroy(), which calls drm_framebuffer_cleanup(),
should only be called after drm_framebuffer_init()
Fix this by just calling kfree() for the allocated fb when an error
happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 3 Sep 2014 19:25:57 +0000 (19:25 +0000)]
drm/omap: add a comment why locking is missing
unpin_worker() calls omap_framebuffer_unpin() without any locks, which
looks very suspicious. However, both pin and unpin are always called via
the driver's private workqueue, so the access is synchronized that way.
Add a comment to make this clear.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 3 Sep 2014 19:25:54 +0000 (19:25 +0000)]
drm/omap: add pin refcounting to omap_framebuffer
omap_framebuffer_pin() and omap_framebuffer_unpin() are currently
broken, as they cannot be called multiple times (i.e. pin, pin, unpin,
unpin), which is what happens in certain cases. This issue causes the
driver to possibly use 0 as an address for a displayed buffer, leading
to OCP error from DSS.
This patch fixes the issue by adding a simple pin_count, used to track
the number of pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 3 Sep 2014 19:25:49 +0000 (19:25 +0000)]
drm/omap: fix encoder-crtc mapping
OMAP DSS hardware supports changing the output port to which an overlay
manager's video stream goes. For example, DPI video stream can come from
any of the four overlay managers on OMAP5.
However, as it's difficult to manage the change in the driver, the
omapdss driver does not support that at the moment, and has a hardcoded
overlay manager per output.
omapdrm, on the other hand, uses the hardware features to find out which
overlay manager to use for an output, which causes problems. For
example, on OMAP5, omapdrm tries to use DIGIT overlay manager for DPI
output, instead of the LCD3 required by the omapdss driver.
This patch changes the omapdrm to use the omapdss driver's hardcoded
overlay managers, which fixes the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Laurent Pinchart [Sat, 17 Jan 2015 21:12:38 +0000 (23:12 +0200)]
drm: omapdrm: Planes are already disabled when destroyed
Planes are destroyed after framebuffers, which has the side effect of
disabling all planes. There is thus no need to disable planes explicitly
when destroying them.
Laurent Pinchart [Wed, 14 Jan 2015 22:45:17 +0000 (00:45 +0200)]
drm: omapdrm: Avoid function forward declaration in omap_crtc.c
Move the set_enabled function to avoid the forward declaration. While at
it prefix it with omap_crtc_ like most other functions in the file, and
fix the comment stating in which contexts the function is called.
Laurent Pinchart [Wed, 14 Jan 2015 22:31:11 +0000 (00:31 +0200)]
drm: omapdrm: Remove omap_crtc->full_update field
The full_update field is always set to true before calling
omap_crtc_appy(), resulting in its value always being true in the single
location where it is tested, in omap_crtc_pre_apply(). Remove it.
Laurent Pinchart [Wed, 14 Jan 2015 15:54:40 +0000 (17:54 +0200)]
drm: omapdrm: Remove manual update display support
All the manual update display code implements eventually ends up to just
calls to omap_connector_flush(), currently implemented as an empty TODO
stub. Remove it, the code can always be revived and implemented later if
interest in manual update displays becomes a reality.
Laurent Pinchart [Tue, 13 Jan 2015 07:14:53 +0000 (09:14 +0200)]
drm: omapdrm: Fix race condition between GO and vblank IRQ
The vblank interrupt is used by the driver as a completion signal when
applying new settings.
A race condition exist between enabling the vblank interrupt and
applying new settings to the hardware by setting the GO bit. If a vblank
interrupt occurs in-between, the driver will incorrectly consider the
new settings to be applied. Fix this by enabling the interrupt after
setting the GO bit.
Laurent Pinchart [Mon, 12 Jan 2015 21:56:57 +0000 (23:56 +0200)]
drm: omapdrm: Reset the zorder property when disabling a plane
Whether to reset plane properties at disable time isn't well-defined in
DRM, but resetting only part of them is probably as bad as it can get.
Make the behaviour coherent by resetting the zorder property in addition
to the rotation property.
Laurent Pinchart [Sat, 10 Jan 2015 22:11:18 +0000 (00:11 +0200)]
drm: omapdrm: Switch to the universal plane API
Remove the CRTC private planes by switching to the universal plane API.
This results in a merge of the CRTC private plane created by the driver
(omap_crtc->plane) and the CRTC primary plane created by the DRM core
(crtc->primary).
Reference counting of the framebuffers in the update plane operation is
thus simplified as no reference needs to be stored in the private plane
anymore.
Dave Airlie [Thu, 19 Mar 2015 04:05:53 +0000 (14:05 +1000)]
Merge branch 'drm_next' of https://github.com/markyzq/kernel-drm-rockchip into drm-next
rockchip fixes.
* 'drm_next' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: vop: power off until vop standby take effect
drm/rockchip: vop: set vop enabled after enable iommu
drm/rockchip: vop use is_enabled instead of dpms mode
drm/rockchip: vop: fix vop vsync/hsync polarity
drm/rockchip: Only alloc a kmap for fbdev gem object
Dave Airlie [Thu, 19 Mar 2015 04:03:39 +0000 (14:03 +1000)]
Merge tag 'topic/drm-misc-2015-03-18' of git://anongit.freedesktop.org/drm-intel into drm-next
Another drm-misch pull request. Mostly the fbdev sizes deconfusion series
from Rob, everything else is small stuff all over. And the large i2c over
aux transfers patch, too.
* tag 'topic/drm-misc-2015-03-18' of git://anongit.freedesktop.org/drm-intel:
drm: check that planes types are correct while initializing CRTC
drm: change connector to tmp_connector
drm: Fix some typo mistake of the annotations
drm: Silence sparse warnings
drm: %pF is only for function pointers
drm/fb: handle tiled connectors better
drm/fb: small cleanup
drm/rockchip: use correct fb width/height
drm/exynos: use correct fb width/height
drm/cma: use correct fb width/height
drm/atomic: minor kerneldoc typo fix
drm/fb: document drm_fb_helper_surface_size
drm/dp: Use large transactions for I2C over AUX
drm/plane-helper: Fixup mismerge
drm/atomic: Constify a bunch of functions pointer structs
John Hunter [Tue, 17 Mar 2015 07:30:28 +0000 (15:30 +0800)]
drm: change connector to tmp_connector
This wasn't too harmful since we already look at connector,
which has the same effect as the loop for any non-cloned configs.
Only when we have a cloned configuration is it important to look
at other connectors. Furthermore existing userspace always changes
dpms on all of them anyway.
Signed-off-by: JohnHunter <zhjwpku@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mark Yao [Thu, 22 Jan 2015 10:29:57 +0000 (18:29 +0800)]
drm/rockchip: vop: set vop enabled after enable iommu
there is a Bug that:
vop_enable()->drm_vblank_on, drm_vblank_on may call vop
enable vblank. if it happen, vblank enable would failed,
then cause irq status error. because is_enabled value is set
after drm_vblank_on.
after enable vop clocks and iommu regs, we can sure that
R/W vop regs and do vop plane flip is safe, so place
is_enabled = true after enable iommu is suitable.
Mark Yao [Thu, 22 Jan 2015 06:37:56 +0000 (14:37 +0800)]
drm/rockchip: vop use is_enabled instead of dpms mode
drm dpms have many power modes: ON,OFF,SUSPEND,STANDBY, etc.
but vop only have enable/disable mode, maybe case such bug:
--> DRM_DPMS_ON: power on vop
--> DRM_DPMS_SUSPEND: power off vop
--> DRM_DPMS_OFF: already power off at SUSPEND, crash
so use a bool val is more suitable.
Mark Yao [Thu, 22 Jan 2015 03:15:02 +0000 (11:15 +0800)]
drm/rockchip: vop: fix vop vsync/hsync polarity
Vop set wrong vsync/hsync polarity, it may cause some
display problem. known problem is that caused HDMI hdcp
authenticate failed, caused pixel offset with hdmi display.
the polarity description at RK3288 TRM doc:
dsp_vsync_pol
VSYNC polarity
1'b0 : negative
1'b1 : positive
dsp_hsync_pol
HSYNC polarity
1'b0 : negative
1'b1 : positive
Signed-off-by: Mark Yao <mark.yao@rock-chips.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Tested-by: Caesar Wang <wxt@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de>
Daniel Kurtz [Mon, 12 Jan 2015 06:58:23 +0000 (14:58 +0800)]
drm/rockchip: Only alloc a kmap for fbdev gem object
In general, the data in drm/rockchip GEM objects is never accessed by
the kernel. The objects are either accessed by a GPU, by display
controller DMA, or by mmap'ing them to user space. Thus, these
buffers need not be mapped into kernel address space.
The only exception is the fbdev framebuffer(s), which may be written
in-kernel by fbcon.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Ville Syrjälä [Fri, 13 Mar 2015 12:51:25 +0000 (14:51 +0200)]
drm: Silence sparse warnings
../drivers/gpu/drm/drm_vm.c:405:6: warning: symbol 'drm_vm_open_locked' was not declared. Should it be static?
../drivers/gpu/drm/drm_vm.c:431:6: warning: symbol 'drm_vm_close_locked' was not declared. Should it be static?
../drivers/gpu/drm/drm_vm.c:681:5: warning: symbol 'drm_vma_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_pci.c:146:5: warning: symbol 'drm_pci_set_unique' was not declared. Should it be static?
../drivers/gpu/drm/drm_pci.c:216:5: warning: symbol 'drm_irq_by_busid' was not declared. Should it be static?
../drivers/gpu/drm/drm_info.c:47:5: warning: symbol 'drm_name_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_info.c:72:5: warning: symbol 'drm_vm_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_info.c:116:5: warning: symbol 'drm_bufs_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_info.c:159:5: warning: symbol 'drm_clients_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_info.c:209:5: warning: symbol 'drm_gem_name_info' was not declared. Should it be static?
../drivers/gpu/drm/drm_ioc32.c:1019:20: warning: symbol 'drm_compat_ioctls' was not declared. Should it be static?
../drivers/gpu/drm/drm_bridge.c:52:12: warning: function 'drm_bridge_attach' with external linkage has definition
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:14 +0000 (10:23 -0400)]
drm/fb: handle tiled connectors better
We don't want tile 0,0 to artificially constrain the size of the legacy
fbdev device. Instead when reducing fb_size to be the minimum of all
displays, only consider the rightmost and bottommost tiles.
Signed-off-by: Rob Clark <robdclark@gmail.com> Tested-by: Hai Li <hali@codeaurora.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:13 +0000 (10:23 -0400)]
drm/fb: small cleanup
Flip conditional to reduce indentation level of rest of fxn, and use
min/max to make the code clearer.
v2: surface_width -> surface_height typo
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:12 +0000 (10:23 -0400)]
drm/rockchip: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:11 +0000 (10:23 -0400)]
drm/exynos: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:10 +0000 (10:23 -0400)]
drm/cma: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:09 +0000 (10:23 -0400)]
drm/atomic: minor kerneldoc typo fix
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rob Clark [Wed, 11 Mar 2015 14:23:08 +0000 (10:23 -0400)]
drm/fb: document drm_fb_helper_surface_size
There has been some confusion about this struct. Lack of documentation
probably didn't help.
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simon Farnsworth [Tue, 10 Feb 2015 18:38:08 +0000 (18:38 +0000)]
drm/dp: Use large transactions for I2C over AUX
Older DisplayPort to DVI-D Dual Link adapters designed by Bizlink have bugs
in their I2C over AUX implementation (fixed in newer revisions). They work
fine with Windows, but fail with Linux.
It turns out that they cannot keep an I2C transaction open unless the
previous read was 16 bytes; shorter reads can only be followed by a zero
byte transfer ending the I2C transaction.
Copy Windows's behaviour, and read 16 bytes at a time. If we get a short
reply, assume that there's a hardware bottleneck, and shrink our read size
to match. For this purpose, use the algorithm in the DisplayPort 1.2 spec,
in the hopes that it'll be closest to what Windows does.
Also provide an unsafe module parameter for testing smaller transfer sizes,
in case there are sinks out there that cannot work with Windows.
Note also that despite the previous comment in drm_dp_i2c_xfer, this speeds
up native DP EDID reads; Ville Syrjälä <ville.syrjala@linux.intel.com> found
the following changes in his testing:
Device under test: old -> with this patch
DP->DVI (OUI 001cf8): 40ms -> 35ms
DP->VGA (OUI 0022b9): 45ms -> 38ms
Zotac DP->2xHDMI: 25ms -> 4ms
Asus PB278 monitor: 22ms -> 3ms
A back of the envelope calculation shows that peak theoretical transfer rate
for 1 byte reads is around 60 kbit/s; with 16 byte reads, this increases to
around 500 kbit/s, which explains the increase in speed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55228 Tested-by: Aidan Marks <aidanamarks@gmail.com> (v3) Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 11 Mar 2015 07:35:47 +0000 (08:35 +0100)]
drm/plane-helper: Fixup mismerge
I somehow manage to screw up applying Laurent's patch in eca93e28c256:
"drm: Check in setcrtc if the primary plane supports the fb pixel
format". It was a conflict with
Dave Airlie [Wed, 11 Mar 2015 02:15:06 +0000 (12:15 +1000)]
Merge tag 'topic/drm-misc-2015-03-10' of git://anongit.freedesktop.org/drm-intel into drm-next
Another pile of misc drm patches all over, mostly polish for atomic. Last
minute rebase was to avoid the broken merge.
* tag 'topic/drm-misc-2015-03-10' of git://anongit.freedesktop.org/drm-intel:
drm: Check in setcrtc if the primary plane supports the fb pixel format
drm: Lighten sysfs connector 'status'
drm/plane-helper: unexport drm_primary_helper_create_plane
drm: Share plane pixel format check code between legacy and atomic
drm: Fix trivial typos in comments
drm/dp: add DPCD definitions from eDP 1.4
drm/dp: add DPCD definitions from DP 1.1 and 1.2a
drm: Fixup racy refcounting in plane_force_disable
drm/i915: Rotation property is now handled in DRM core
drm: Complete moving rotation property to core
drm/dp: add DPCD definitions from eDP 1.2
drm/dp: indentation and ordering cleanups
drm/atomic-helper: Fix kerneldoc for prepare_planes
drm: Remove redundant code in the getencoder ioctl
drm: Check in setcrtc if the primary plane supports the fb pixel format
Drivers implementing the universal planes API report the list of
supported pixel formats for the primary plane. Make sure the fb passed
to the setcrtc ioctl is compatible.
Drivers not implementing the universal planes API will have no format
reported for the primary plane, skip the check in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 6 Mar 2015 12:36:42 +0000 (12:36 +0000)]
drm: Lighten sysfs connector 'status'
Since the beginning, sysfs/connector/status has done a heavyweight
detection of the current connector status. But no user, such as upowerd
or logind, has ever desired to initiate a probe. Move the probing into a
new attribute so that existing readers get the behaviour they desire.
v2: David Herrmann suggested using "echo detect > /sys/.../status" to
trigger the probing, which is a fine idea. This extends that to also
allow the user to apply the force detection overrides at runtime.
v3: Now with airlied's email address fixed! Requires sysfs_streq()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Alex Deucher <alexdeucher@gmail.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We shouldn't tempt driver writers into using this since it uses a
default format list which is likely wrong. And when that's done we can
simplify the code a bit, too.
Noticed while reviewing a patch from Laurent.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
we've switched to weak references, broke that assumption but forgot to
fix it up.
Since we still force-disable planes it's only possible to hit this
when racing multiple rmfb with fbdev restoring or similar evil things.
As long as userspace is nice it's impossible to hit the BUG_ON.
But the BUG_ON would most likely be hit from fbdev code, which usually
invovles the console_lock besides all modeset locks. So very likely
we'd never get the bug reports if this was hit in the wild, hence
better be safe than sorry and backport.
Spotted by Matt Roper while reviewing other patches.
Cc: stable@vger.kernel.org Cc: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tvrtko Ursulin [Thu, 26 Feb 2015 13:49:17 +0000 (13:49 +0000)]
drm: Complete moving rotation property to core
Commit 1da30627fc511a57c9bd23a02c97f0576379f761 "drm: Add rotation value to
plane state" moved the rotation property to DRM core but only did the set
property part. This does the get property part as well.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm: Handle atomic state properly in kms getfoo ioctl
I've forgotten to remove this hunk in one of the later revisions.
drm_encoder_get_crtc already does this.
Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <seanpaul@chromium.org> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
managed to pick the wrong code to resolve the conflict and left us with
a mutex_lock(struct_mutex) without the mutex_unlock(struct_mutex) leading
to a deadlock. Fix the problem by recovering the correct code which doesn't
need the lock.
Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 9 Mar 2015 09:41:15 +0000 (19:41 +1000)]
Merge tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel into drm-next
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
Linus Torvalds [Sun, 8 Mar 2015 19:47:18 +0000 (12:47 -0700)]
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Linus Torvalds [Sun, 8 Mar 2015 19:25:40 +0000 (12:25 -0700)]
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Linus Torvalds [Sun, 8 Mar 2015 19:15:47 +0000 (12:15 -0700)]
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
Linus Torvalds [Sun, 8 Mar 2015 18:51:04 +0000 (11:51 -0700)]
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Linus Torvalds [Sat, 7 Mar 2015 19:31:17 +0000 (11:31 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kernel/module.c: Update debug alignment after symtable generation
arm64: Don't use is_module_addr in setting page attributes
Johan Hovold [Wed, 4 Mar 2015 09:39:07 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent maximum timeout
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 4 Mar 2015 09:39:06 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent on 64-bit machines
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:24:28 +0000 (10:24 -0500)]
serial: uapi: Declare all userspace-visible io types
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:18:16 +0000 (10:18 -0500)]
serial: core: Fix iotype userspace breakage
commit 3ffb1a8193bea ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.
Cc: Kevin Cernekee <cernekee@gmail.com> Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Reviewed-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Axel Lin [Mon, 16 Feb 2015 14:39:04 +0000 (22:39 +0800)]
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 1 Mar 2015 15:11:05 +0000 (10:11 -0500)]
console: Fix console name size mismatch
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: John Paul Perry <john_paul.perry@alcatel-lucent.com> Cc: <stable@vger.kernel.org> # all, as b0b885657 was backported Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Desmond Liu [Fri, 27 Feb 2015 00:35:57 +0000 (16:35 -0800)]
serial: 8250_dw: Fix get_mctrl behaviour
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reported-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO") Reported-By: Nicolas Schichan <nschichan@freebox.fr> Debuged-By: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 7 Mar 2015 00:54:22 +0000 (16:54 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon, imx, msm, and i915 fixes.
The msm, imx and i915 ones are fairly run of the mill.
Radeon had some DP audio and posting reads for irq fixes, along with a
fix for 32-bit kernels with new cards, we were using unsigned long to
represent GPU side memory space, but since that changed size on 32 vs
64 cards with lots of VRAM failed, so the change has no effect on
x86-64, just moves to using uint64_t instead"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/msm: kexec fixes
drm/msm/mdp5: fix cursor blending
drm/msm/mdp5: fix cursor ROI
drm/msm/atomic: Don't leak atomic commit object when commit fails
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
drm/msm: update generated headers (add 6th lm.base entry)
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
drm/ttm: device address space != CPU address space
drm/mm: Support 4 GiB and larger ranges
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
...
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>