Russell King [Sat, 11 Jan 2014 11:25:37 +0000 (11:25 +0000)]
ARM: SMP implementations are not supposed to return from smp_ops.cpu_die()
Although we allow recovery in this case, this is not supposed to be
the normal path for hotplugging a CPU back in. This path only exists
to serve those rare platforms where it's not possible to power down
the CPU or reset the CPU. This patch causes the kernel to print a
message when a platform uses this path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 11 Jan 2014 11:22:18 +0000 (11:22 +0000)]
ARM: ignore memory below PHYS_OFFSET
If the kernel is loaded higher in physical memory than normal, and we
calculate PHYS_OFFSET higher than the start of RAM, this leads to
boot problems as we attempt to map part of this RAM into userspace.
Rather than struggle with this, just truncate the mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 1 Jan 2014 11:59:44 +0000 (11:59 +0000)]
Fix select-induced Kconfig warning for ZBOOT_ROM
warning: (ARCH_MULTIPLATFORM && ARCH_CLPS711X && ARCH_PXA &&
SOC_EXYNOS5440 && ARCH_EMEV2) selects AUTO_ZRELADDR which
has unmet direct dependencies (!ZBOOT_ROM)
This is because it's possible to have ZBOOT_ROM enabled, but at the
same time have another option enabled which selects AUTO_ZRELADDR
overriding the !ZBOOT_ROM dependency. Fix this by reversing the
dependencies between ZBOOT_ROM and the options which depend on
!ZBOOT_ROM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 13 Jan 2014 23:34:56 +0000 (23:34 +0000)]
ARM: fix ffs/fls implementations to match x86
ARMs ffs/fls implementations are not type compatible with x86, so when
they're used in combination with min()/max(), they provoke warnings.
Change these to be inline functions with the correct types, providing
the clz as a separate documentation, and document their individual
behaviours.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Taras Kondratiuk [Fri, 10 Jan 2014 00:27:08 +0000 (01:27 +0100)]
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
collie has several GPIO lines that act like keys - Sync/Wakeup button on
dock station is connected to GPIO line. Another one is connected to
on/off button. Add corresponding gpio-keys configuration.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Taras Kondratiuk [Fri, 10 Jan 2014 00:36:00 +0000 (01:36 +0100)]
ARM: 7939/1: traps: fix opcode endianness when read from user memory
Currently code has an inverted logic: opcode from user memory
is swapped to a proper endianness only in case of read error.
While normally opcode should be swapped only if it was read
correctly from user memory.
Reviewed-by: Victor Kamensky <victor.kamensky@linaro.org> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Thu, 9 Jan 2014 23:57:06 +0000 (00:57 +0100)]
ARM: 7937/1: perf_event: Silence sparse warning
arch/arm/kernel/perf_event_cpu.c:274:25: warning: incorrect type in assignment (different modifiers)
arch/arm/kernel/perf_event_cpu.c:274:25: expected int ( *init_fn )( ... )
arch/arm/kernel/perf_event_cpu.c:274:25: got void const *const data
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sudeep Holla [Wed, 8 Jan 2014 17:24:21 +0000 (18:24 +0100)]
ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match
The MPIDR contains specific bitfields(MPIDR.Aff{2..0}) which uniquely
identify a CPU, in addition to some non-identifying information and
reserved bits. The ARM cpu binding defines the 'reg' property to only
contain the affinity bits, and any cpu nodes with other bits set in
their 'reg' entry are skipped.
As such it is not necessary to mask the phys_id with MPIDR_HWID_BITMASK,
and doing so could lead to matching erroneous CPU nodes in the device
tree. This patch removes the masking of the physical identifier.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Jan 2014 17:53:54 +0000 (17:53 +0000)]
Revert "ARM: 7908/1: mm: Fix the arm_dma_limit calculation"
This reverts commit 787b0d5c1ca7ff24feb6f92e4c7f4410ee7d81a8 since
it is no longer required after 7909/1 was applied, and it causes
build regressions when ARM_PATCH_PHYS_VIRT is disabled and DMA_ZONE
is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rob Herring [Fri, 3 Jan 2014 15:17:44 +0000 (16:17 +0100)]
ARM: 7933/1: rename ioremap_cached to ioremap_cache
ioremap_cache is more aligned with other architectures.
There are only 2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64:
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 2 Jan 2014 17:14:45 +0000 (17:14 +0000)]
CRYPTO: Fix more AES build errors
Building a multi-arch kernel results in:
arch/arm/crypto/built-in.o: In function `aesbs_xts_decrypt':
sha1_glue.c:(.text+0x15c8): undefined reference to `bsaes_xts_decrypt'
arch/arm/crypto/built-in.o: In function `aesbs_xts_encrypt':
sha1_glue.c:(.text+0x1664): undefined reference to `bsaes_xts_encrypt'
arch/arm/crypto/built-in.o: In function `aesbs_ctr_encrypt':
sha1_glue.c:(.text+0x184c): undefined reference to `bsaes_ctr32_encrypt_blocks'
arch/arm/crypto/built-in.o: In function `aesbs_cbc_decrypt':
sha1_glue.c:(.text+0x19b4): undefined reference to `bsaes_cbc_encrypt'
This code is already runtime-conditional on NEON being supported, so
there's no point compiling it out depending on the minimum build
architecture.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Fri, 3 Jan 2014 21:48:25 +0000 (13:48 -0800)]
Merge tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6
Pull battery fixes from Anton Vorontsov:
"Two fixes:
- fix build error caused by max17042_battery conversion to the regmap
API.
- fix kernel oops when booting with wakeup_source_activate enabled"
* tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6:
max17042_battery: Fix build errors caused by missing REGMAP_I2C config
power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate
Linus Torvalds [Fri, 3 Jan 2014 21:44:41 +0000 (13:44 -0800)]
Merge tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
"These commits, except for one, are regression fixes and the remaining
one fixes a divide error leading to a kernel panic. The majority of
the regressions fixed here were introduced during the 3.12 cycle, one
of them is from this cycle and one is older.
Specifics:
- VGA switcheroo was broken for some users as a result of the
ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
previously ignored hotplug events started to be handled. The fix
causes them to be ignored again.
- There are two more issues related to cpufreq's suspend/resume
handling changes from the 3.12 cycle addressed by Viresh Kumar's
fixes.
- intel_pstate triggers a divide error in a timer function if the
P-state information it needs is missing during initialization.
This leads to kernel panics on nested KVM clients and is fixed by
failing the initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work
around them by installing an ACPI wakeup notify handler for all PCI
devices with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init,
which is incorrect and causes a section mismatch to occur during
build. Fix from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about
missing _ADR for devices that legitimately don't have it. Fix from
Toshi Kani makes it only print the warnings where they make sense"
* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
intel_pstate: Fail initialization if P-state information is missing
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
ACPI / PCI / hotplug: Avoid warning when _ADR not present
Linus Torvalds [Thu, 2 Jan 2014 22:40:38 +0000 (14:40 -0800)]
Merge branch 'akpm' (incoming from Andrew)
Merge patches from Andrew Morton:
"Ten fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
mm/memory-failure.c: transfer page count from head page to tail page after split thp
MAINTAINERS: set up proper record for Xilinx Zynq
mm: remove bogus warning in copy_huge_pmd()
memcg: fix memcg_size() calculation
mm: fix use-after-free in sys_remap_file_pages
mm: munlock: fix deadlock in __munlock_pagevec()
mm: munlock: fix a bug where THP tail page is encountered
Jason Baron [Thu, 2 Jan 2014 20:58:54 +0000 (12:58 -0800)]
epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x). The deadlock was introduced with
commmit 67347fe4e632 ("epoll: do not take global 'epmutex' for simple
topologies").
The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')
However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.
The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon. The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock. Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: Nathan Zimmer <nzimmer@sgi.com> Cc: Eric Wong <normalperson@yhbt.net> Cc: Nelson Elhage <nelhage@nelhage.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
Min_low_pfn and max_low_pfn were used in pfn_valid macro if defined
CONFIG_FLATMEM. When the functions that use the pfn_valid is used in
driver module, max_low_pfn and min_low_pfn is to undefined, and fail to
build.
Naoya Horiguchi [Thu, 2 Jan 2014 20:58:51 +0000 (12:58 -0800)]
mm/memory-failure.c: transfer page count from head page to tail page after split thp
Memory failures on thp tail pages cause kernel panic like below:
mce: [Hardware Error]: Machine check events logged
MCE exception done on CPU 7
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff811b7cd1>] dequeue_hwpoisoned_huge_page+0x131/0x1e0
PGD bae42067 PUD ba47d067 PMD 0
Oops: 0000 [#1] SMP
...
CPU: 7 PID: 128 Comm: kworker/7:2 Tainted: G M O 3.13.0-rc4-131217-1558-00003-g83b7df08e462 #25
...
Call Trace:
me_huge_page+0x3e/0x50
memory_failure+0x4bb/0xc20
mce_process_work+0x3e/0x70
process_one_work+0x171/0x420
worker_thread+0x11b/0x3a0
? manage_workers.isra.25+0x2b0/0x2b0
kthread+0xe4/0x100
? kthread_create_on_node+0x190/0x190
ret_from_fork+0x7c/0xb0
? kthread_create_on_node+0x190/0x190
...
RIP dequeue_hwpoisoned_huge_page+0x131/0x1e0
CR2: 0000000000000058
The reasoning of this problem is shown below:
- when we have a memory error on a thp tail page, the memory error
handler grabs a refcount of the head page to keep the thp under us.
- Before unmapping the error page from processes, we split the thp,
where page refcounts of both of head/tail pages don't change.
- Then we call try_to_unmap() over the error page (which was a tail
page before). We didn't pin the error page to handle the memory error,
this error page is freed and removed from LRU list.
- We never have the error page on LRU list, so the first page state
check returns "unknown page," then we move to the second check
with the saved page flag.
- The saved page flag have PG_tail set, so the second page state check
returns "hugepage."
- We call me_huge_page() for freed error page, then we hit the above panic.
The root cause is that we didn't move refcount from the head page to the
tail page after split thp. So this patch suggests to do this.
This panic was introduced by commit 524fca1e73 ("HWPOISON: fix
misjudgement of page_action() for errors on mlocked pages"). Note that we
did have the same refcount problem before this commit, but it was just
ignored because we had only first page state check which returned "unknown
page." The commit changed the refcount problem from "doesn't work" to
"kernel panic."
This warning was introduced by "mm: numa: Avoid unnecessary disruption
of NUMA hinting during migration" for paranoia reasons but the warning
is bogus. I was thinking of parallel races between NUMA hinting faults
and forks but this warning would also be triggered by a parallel reclaim
splitting a THP during a fork. Remote the bogus warning.
Signed-off-by: Mel Gorman <mgorman@suse.de> Reported-by: Sasha Levin <sasha.levin@oracle.com> Cc: Alex Thorlton <athorlton@sgi.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Thu, 2 Jan 2014 20:58:46 +0000 (12:58 -0800)]
mm: fix use-after-free in sys_remap_file_pages
remap_file_pages calls mmap_region, which may merge the VMA with other
existing VMAs, and free "vma". This can lead to a use-after-free bug.
Avoid the bug by remembering vm_flags before calling mmap_region, and
not trying to dereference vma later.
Signed-off-by: Rik van Riel <riel@redhat.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: PaX Team <pageexec@freemail.hu> Cc: Kees Cook <keescook@chromium.org> Cc: Michel Lespinasse <walken@google.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Thu, 2 Jan 2014 20:58:44 +0000 (12:58 -0800)]
mm: munlock: fix deadlock in __munlock_pagevec()
Commit 7225522bb429 ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec" introduced __munlock_pagevec() to speed
up munlock by holding lru_lock over multiple isolated pages. Pages that
fail to be isolated are put_page()d immediately, also within the lock.
This can lead to deadlock when __munlock_pagevec() becomes the holder of
the last page pin and put_page() leads to __page_cache_release() which
also locks lru_lock. The deadlock has been observed by Sasha Levin
using trinity.
This patch avoids the deadlock by deferring put_page() operations until
lru_lock is released. Another pagevec (which is also used by later
phases of the function is reused to gather the pages for put_page()
operation.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Sasha Levin <sasha.levin@oracle.com> Cc: Michel Lespinasse <walken@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Thu, 2 Jan 2014 20:58:43 +0000 (12:58 -0800)]
mm: munlock: fix a bug where THP tail page is encountered
Since commit ff6a6da60b89 ("mm: accelerate munlock() treatment of THP
pages") munlock skips tail pages of a munlocked THP page. However, when
the head page already has PageMlocked unset, it will not skip the tail
pages.
Commit 7225522bb429 ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec") has added a PageTransHuge() check which
contains VM_BUG_ON(PageTail(page)). Sasha Levin found this triggered
using trinity, on the first tail page of a THP page without PageMlocked
flag.
This patch fixes the issue by skipping tail pages also in the case when
PageMlocked flag is unset. There is still a possibility of race with
THP page split between clearing PageMlocked and determining how many
pages to skip. The race might result in former tail pages not being
skipped, which is however no longer a bug, as during the skip the
PageTail flags are cleared.
However this race also affects correctness of NR_MLOCK accounting, which
is to be fixed in a separate patch.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Sasha Levin <sasha.levin@oracle.com> Cc: Michel Lespinasse <walken@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Bob Liu <bob.liu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Jan 2014 20:45:47 +0000 (12:45 -0800)]
Merge tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes
Pull GFS2 fixes from Steven Whitehouse:
"Here is a set of small fixes for GFS2. There is a fix to drop
s_umount which is copied in from the core vfs, two patches relate to a
hard to hit "use after free" and memory leak. Two patches related to
using DIO and buffered I/O on the same file to ensure correct
operation in relation to glock state changes. The final patch adds an
RCU read lock to ensure correct locking on an error path"
* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Fix unsafe dereference in dump_holder()
GFS2: Wait for async DIO in glock state changes
GFS2: Fix incorrect invalidation for DIO/buffered I/O
GFS2: Fix slab memory leak in gfs2_bufdata
GFS2: Fix use-after-free race when calling gfs2_remove_from_ail
GFS2: don't hold s_umount over blkdev_put
Linus Torvalds [Thu, 2 Jan 2014 20:45:07 +0000 (12:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two small bug fixes and a follow-up to the CONFIG_NR_CPUS change.
A kernel compiled with CONFIG_NR_CPUS=256 will waste quite a bit of
memory for the per-cpu arrays. Under z/VM the maximum number of CPUs
is 64, the code now limits the possible cpu mask to 64 if running
under z/VM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: obtain function handle in hotplug notifier
s390/3270: fix allocation of tty3270_screen structure
s390/smp: improve setup of possible cpu mask
Jan Kiszka [Sat, 28 Dec 2013 15:31:52 +0000 (16:31 +0100)]
KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
Three reasons for doing this: 1. arch.walk_mmu points to arch.mmu anyway
in case nested EPT wasn't in use. 2. this aligns VMX with SVM. But 3. is
most important: nested_cpu_has_ept(vmcs12) queries the VMCS page, and if
one guest VCPU manipulates the page of another VCPU in L2, we may be
fooled to skip over the nested_ept_uninit_mmu_context, leaving mmu in
nested state. That can crash the host later on if nested_ept_get_cr3 is
invoked while L1 already left vmxon and nested.current_vmcs12 became
NULL therefore.
Cc: stable@kernel.org Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Wed, 1 Jan 2014 19:36:16 +0000 (11:36 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull radeon drm fixes from Dave Airlie:
"Just piping a bunch of fixes from pre-xmas from Alex for radeon, all
either fix bad hw setup issues or regressions"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Bump version for CIK DCE tiling fix
drm/radeon: set correct number of banks for CIK chips in DCE
drm/radeon: set correct pipe config for Hawaii in DCE
drm/radeon: expose render backend mask to the userspace
drm/radeon: fix render backend setup for SI and CIK
drm/radeon: 0x9649 is SUMO2 not SUMO
drm/radeon: fix UVD 256MB check
Dave Airlie [Wed, 1 Jan 2014 10:32:19 +0000 (20:32 +1000)]
Merge branch 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Radeon fixes, Christmas eve edition. Fix incorrect family for 0x9649
which lead to bogus rendering, tiling and RB fixes for SI and CIK,
and a UVD fix.
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Bump version for CIK DCE tiling fix
drm/radeon: set correct number of banks for CIK chips in DCE
drm/radeon: set correct pipe config for Hawaii in DCE
drm/radeon: expose render backend mask to the userspace
drm/radeon: fix render backend setup for SI and CIK
drm/radeon: 0x9649 is SUMO2 not SUMO
drm/radeon: fix UVD 256MB check
Krzysztof Hałasa [Tue, 31 Dec 2013 10:51:16 +0000 (11:51 +0100)]
crypto: ixp4xx - Fix kernel compile error
drivers/crypto/ixp4xx_crypto.c: In function 'ixp_module_init':
drivers/crypto/ixp4xx_crypto.c:1419:2: error: 'dev' undeclared (first use in this function)
Now builds. Not tested on real hw.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* pm-cpufreq:
intel_pstate: Fail initialization if P-state information is missing
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
* pm-cpuidle:
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
Merge branches 'acpi-pci-pm' and 'acpi-pci-hotplug'
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
Linus Torvalds [Tue, 31 Dec 2013 20:19:30 +0000 (12:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A fix for a panic in gpio-keys driver when set up with absolute
events, a fixup to the new zforce driver and a new keycode definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: allocate absinfo data when setting ABS capability
Input: define KEY_WWAN for Wireless WAN
Input: zforce - fix possible driver hang during suspend
Linus Torvalds [Tue, 31 Dec 2013 20:17:14 +0000 (12:17 -0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A few small cifs fixes including two for stable, and fixing a
regression introduced by the VFS change to file create"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: set FILE_CREATED
cifs: We do not drop reference to tlink in CIFSCheckMFSymlink()
Add missing end of line termination to some cifs messages
Dmitry Torokhov [Fri, 27 Dec 2013 01:44:29 +0000 (17:44 -0800)]
Input: allocate absinfo data when setting ABS capability
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891 Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk> Reported-and-tested-by: <madcatx@atlas.cz> Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com> Cc: Alex Deucher <alexdeucher@gmail.com> Cc: Dave Airlie <airlied@linux.ie> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
intel_pstate: Fail initialization if P-state information is missing
If pstate.current_pstate is 0 after the initial
intel_pstate_get_cpu_pstates(), this means that we were unable to
obtain any useful P-state information and there is no reason to
continue, so free memory and return an error in that case.
This fixes the following divide error occuring in a nested KVM
guest:
Jan Kiszka [Sun, 29 Dec 2013 01:29:30 +0000 (02:29 +0100)]
KVM: x86: Fix APIC map calculation after re-enabling
Update arch.apic_base before triggering recalculate_apic_map. Otherwise
the recalculation will work against the previous state of the APIC and
will fail to build the correct map when an APIC is hardware-enabled
again.
Linus Torvalds [Mon, 30 Dec 2013 18:22:57 +0000 (10:22 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com> Signed-off-by: Rob Herring <robh@kernel.org>
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
With commit e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 0000000100000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 000000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 010000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 010000000000000000000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 00000000ffc10000
OF: with offset: 70
OF: one level translation: 00000000ffc10070
OF: reached root node
With commit e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 0000000100000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 010000000000000000000000
OF: with offset: 70
OF: one level translation: 000000000000000000000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Rob Herring <robh@kernel.org>
Andre Przywara [Fri, 13 Dec 2013 20:49:19 +0000 (21:49 +0100)]
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
Commit 60a66e370007e8535b7a561353b07b37deaf35ba changed the Calxeda
cpuidle driver to a platform driver, copying the __init tag from the
_init() to the newly used _probe() function. However, "probe should
not be __init." (Rob said ;-)
Remove the __init tag to fix a section mismatch in the Calxeda
cpuidle driver.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Sebastian Ott [Wed, 18 Dec 2013 15:46:02 +0000 (16:46 +0100)]
s390/pci: obtain function handle in hotplug notifier
When using the CLP interface to enable or disable a pci device a
valid function handle needs to be delivered. So far our assumption
was that we always have an up-to-date version of the function handle
(since it doesn't change when the device is in use). This assumption
is incorrect if the pci device is enabled or disabled outside of our
control. When we are notified about such a change we already receive
the new function handle. Just use it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Vince Bridgers [Fri, 20 Dec 2013 17:19:34 +0000 (11:19 -0600)]
stmmac: Fix incorrect spinlock release and PTP cap detection.
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Fri, 20 Dec 2013 19:09:04 +0000 (22:09 +0300)]
phy: IRQ cannot be shared
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Sun, 22 Dec 2013 23:32:31 +0000 (00:32 +0100)]
net: rose: restore old recvmsg behavior
recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.
After commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.
Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Mon, 23 Dec 2013 09:27:17 +0000 (09:27 +0000)]
xen-netback: fix guest-receive-side array sizes
The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;
- The meta array is needlessly twice the ring size, when we only ever
consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
assumption: that at most two copy ops will be used per ring slot. This
may have been true at some point in the past but it's clear from looking
at start_new_rx_buffer() that a new ring slot is only consumed if a frag
would overflow the current slot (plus some other conditions) so the actual
limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.
This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Tue, 24 Dec 2013 14:16:01 +0000 (12:16 -0200)]
fec: Do not assume that PHY reset is active low
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The opposite order of holding port lock and node lock on above two
different paths may result in a deadlock. If socket lock instead of
port lock is used to protect port instance in tipc_withdraw(), the
reverse order of holding port lock and node lock will be eliminated,
as a result, the deadlock is killed as well.
Reported-by: Lars Everbrand <lars.everbrand@ericsson.com> Reviewed-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Sat, 28 Dec 2013 21:01:47 +0000 (13:01 -0800)]
powerpc: Fix alignment of secondary cpu spin vars
Commit 5c0484e25ec0 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25ec0 ('powerpc: Endian safe trampoline') Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811 Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 23 Dec 2013 01:19:51 +0000 (12:19 +1100)]
powerpc: Align p_end
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Fri, 20 Dec 2013 19:06:01 +0000 (13:06 -0600)]
powernv/eeh: Add buffer for P7IOC hub error data
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Thu, 19 Dec 2013 23:14:07 +0000 (17:14 -0600)]
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com> Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul E. McKenney [Tue, 17 Dec 2013 22:29:57 +0000 (09:29 +1100)]
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make unaligned accesses endian-safe for powerpc
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 16 Dec 2013 04:12:43 +0000 (15:12 +1100)]
powerpc: Fix bad stack check in exception entry
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit d2e5f0c16ad6 (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.
Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them. The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.
Fixes: d2e5f0c16ad6 (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021 Reported-and-tested-by: Agustin Barto <abarto@gmail.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Sun, 29 Dec 2013 21:49:51 +0000 (13:49 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Linus Torvalds [Sun, 29 Dec 2013 21:35:04 +0000 (13:35 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
Linus Torvalds [Sun, 29 Dec 2013 21:27:51 +0000 (13:27 -0800)]
Merge tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
Viresh Kumar [Tue, 24 Dec 2013 01:41:01 +0000 (07:11 +0530)]
cpufreq: preserve user_policy across suspend/resume
Prevent __cpufreq_add_dev() from overwriting the existing values of
user_policy.{min|max|policy|governor} with defaults during resume
from system suspend.
Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: Clean up after a failing light-weight initialization
If cpufreq_policy_restore() returns NULL during system resume,
__cpufreq_add_dev() should just fall back to the full initialization
instead of returning an error, because that may actually make things
work. Moreover, it should not leave stale fallback data behind after
it has failed to restore a previously existing policy.
This change is based on Viresh Kumar's work.
Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Christian Daudt [Mon, 23 Dec 2013 08:00:01 +0000 (09:00 +0100)]
ARM: 7932/1: bcm: Add DEBUG_LL console support
This patch adds low level debug uart support to Broadcom mobile based
SOCs.
Signed-off-by: Christian Daudt <bcm@fixthebug.org> Tested-by: Markus Mayer <markus.mayer@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Tested-by: Matt Porter <mporter@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 17 Dec 2013 18:50:16 +0000 (19:50 +0100)]
ARM: 7928/1: kconfig: select HAVE_EFFICIENT_UNALIGNED_ACCESS for CPUv6+ && MMU
Modern ARM CPUs can perform efficient unaligned memory accesses in
hardware and this feature is relied up on by code such as the dcache
word-at-a-time name hashing.
This patch selects HAVE_EFFICIENT_UNALIGNED_ACCESS for these cores and
reworks the kconfig select logic for DCACHE_WORD_ACCESS to use the new
symbol.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 17 Dec 2013 18:50:11 +0000 (19:50 +0100)]
ARM: 7927/1: dcache: select DCACHE_WORD_ACCESS for big-endian CPUs
With commit 11ec50caedb5 ("word-at-a-time: provide generic big-endian
zero_bytemask implementation"), the asm-generic word-at-a-time code now
provides a zero_bytemask implementation, allowing us to make use of
DCACHE_WORD_ACCESS on big-endian CPUs, providing our
load_unaligned_zeropad function is endianness-clean.
This patch reworks the load_unaligned_zeropad fixup code to work for
both big- and little-endian CPUs, then removes the !CPU_BIG_ENDIAN check
when selecting DCACHE_WORD_ACCESS.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 17 Dec 2013 18:17:54 +0000 (19:17 +0100)]
ARM: 7926/1: mm: flesh out and fix the comments in the ASID allocator
The ASID allocator has to deal with some pretty horrible behaviours by
the CPU, so expand on some of the comments in there so I remember why
we can never allocate ASID zero to a userspace task.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 17 Dec 2013 18:17:31 +0000 (19:17 +0100)]
ARM: 7925/1: mm: keep track of last ASID allocation to improve bitmap searching
Since we only clear entries in the ASID bitmap on a rollover event, the
bitmap tends to consist of a block of consecutive set bits followed by
a block of consecutive clear bits. The exception to this rule is for
ASIDs which have been carried over from a previous generation, but
these are bound by the number of CPUs.
This patch optimises our bitmap searching strategy, so that we search
from the last successful allocation, rather than search from index 1
each time we allocate a new ASID.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 17 Dec 2013 18:17:11 +0000 (19:17 +0100)]
ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE
With the new ASID allocation algorithm, active ASIDs at the time of a
rollover event will be marked as reserved, so active mm_structs can
continue to operate with the same ASID as before. This in turn means
that we don't need to worry about allocating a new ASID to an mm that
is currently active (installed in TTBR0).
Since updating the pgd and ASID is atomic on LPAE systems (by virtue of
the two being fields in the same hardware register), we can dispose of
the reserved TTBR0 and rely on whatever tables we currently have live.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Laura Abbott [Sat, 21 Dec 2013 00:03:06 +0000 (01:03 +0100)]
ARM: 7931/1: Correct virt_addr_valid
The definition of virt_addr_valid is that virt_addr_valid should
return true if and only if virt_to_page returns a valid pointer.
The current definition of virt_addr_valid only checks against the
virtual address range. There's no guarantee that just because a
virtual address falls bewteen PAGE_OFFSET and high_memory the
associated physical memory has a valid backing struct page. Follow
the example of other architectures and convert to pfn_valid to
verify that the virtual address is actually valid. The check for
an address between PAGE_OFFSET and high_memory is still necessary
as vmalloc/highmem addresses are not valid with virt_to_page.
Cc: Will Deacon <will.deacon@arm.com> Cc: Nicolas Pitre <nico@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Steven Capper [Mon, 16 Dec 2013 16:25:52 +0000 (17:25 +0100)]
ARM: 7923/1: mm: fix dcache flush logic for compound high pages
When given a compound high page, __flush_dcache_page will only flush
the first page of the compound page repeatedly rather than the entire
set of constituent pages.
This error was introduced by: 0b19f93 ARM: mm: Add support for flushing HugeTLB pages.
This patch corrects the logic such that all constituent pages are now
flushed.
Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Dec 2013 12:42:25 +0000 (12:42 +0000)]
ARM: PCI: add legacy IDE IRQ implementation
The IDE code used to specify the IDE IRQs for chipsets operating in
legacy mode. This appears to no longer work, and this information must
be provided by the arch. Do so. This partially fixes CY82C693 (and
probably others) on Footbridge platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Dec 2013 12:39:50 +0000 (12:39 +0000)]
ARM: fix footbridge clockevent device
The clockevents code was being told that the footbridge clock event
device ticks at 16x the rate which it actually does. This leads to
timekeeping problems since it allows the clocksource to wrap before
the kernel notices. Fix this by using the correct clock.
Fixes: 4e8d76373c9fd ("ARM: footbridge: convert to clockevents/clocksource") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: <stable@vger.kernel.org>
Russell King [Sat, 30 Nov 2013 13:41:26 +0000 (13:41 +0000)]
ARM: footbridge: cleanup LEDs code
Cleanup the LEDs code to use ioremap()/writeb() to access the register.
This allows us to move the definitions out of a header file directly
into the ebsa285 support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for the Marvell Tauros3 cache controller which
is compatible with pl310 cache controller but broadcasts L1 cache
operations to L2 cache. While updating the binding documentation,
clean up the list of possible compatibles. Also reorder driver
compatibles to allow non-ARM derivated to be compatible to ARM
cache controller compatibles.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kim Phillips [Wed, 6 Nov 2013 04:15:24 +0000 (05:15 +0100)]
ARM: 7877/1: use built-in byte swap function
Enable the compiler intrinsic for byte swapping on arch ARM. This
allows the compiler to detect and be able to optimize out byte
swappings, and has a very modest benefit on vmlinux size (Linaro gcc
4.8):
text data bss dec hex filename 2840310 123932 61960 3026202 2e2d1a vmlinux-lart #orig 2840152 123932 61960 3026044 2e2c7c vmlinux-lart #builtin-bswap
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 10 Dec 2013 19:12:27 +0000 (20:12 +0100)]
ARM: 7921/1: mcpm: remove redundant dsb instructions prior to sev
sync_cache_w already includes a dsb, so we can just use sev() directly
then following a cache-sync.
Acked-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These symbols are only referenced in this source file so can be made
static, and the efficiency table is constant data so can be declared as
such. This avoids polluting the global namespace and fixes warnings
from sparse.
The function arch_scale_freq_power() is still not prototyped or static,
this is a separate issue as this is overriding a weak symbol from the
scheduler which neglects to provide a prototype.
Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Dec 2013 22:49:14 +0000 (22:49 +0000)]
ARM: fix csum_tcpudp_magic() miscompilation
There is a miscompilation of csum_tcpudp_magic() due to the way we pass
the asm() operands in. Fortunately, this doesn't affect the IP code,
but can affect anyone who passes ntohs(udp->len) as the length argument,
or protocols with more than 8 bits.
The problem stems from passing 16-bit operands into an asm() - GCC makes
no guarantees about what may be in the high 16-bits of such a register
passed into assembly which is in the "HI" machine mode.
Address this by changing the way we handle the 16-bit arguments - since
accumulating the protocol and length can never overflow, we can delegate
this to the compiler to perform, and then accumulate it into the
checksum inside the asm(), taking account of the endian-ness via an
appropriate 32-bit rotation.
While we are here, also realise that there's a chance to optimise this
a little: several callers from IP code pass a constant zero as the
initial sum. This is wasteful - if we detect this condition, we can
optimise away one instruction.
Tested-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 7919/1: mm: refactor v7 cache cleaning ops to use way/index sequence
Set-associative caches on all v7 implementations map the index bits
to physical addresses LSBs and tag bits to MSBs. As the last level
of cache on current and upcoming ARM systems grows in size,
this means that under normal DRAM controller configurations, the
current v7 cache flush routine using set/way operations triggers a
DRAM memory controller precharge/activate for every cache line
writeback since the cache routine cleans lines by first fixing the
index and then looping through ways (index bits are mapped to lower
physical addresses on all v7 cache implementations; this means that,
with last level cache sizes in the order of MBytes, lines belonging
to the same set but different ways map to different DRAM pages).
Given the random content of cache tags, swapping the order between
indexes and ways loops do not prevent DRAM pages precharge and
activate cycles but at least, on average, improves the chances that
either multiple lines hit the same page or multiple lines belong to
different DRAM banks, improving throughput significantly.
This patch swaps the inner loops in the v7 cache flushing routine
to carry out the clean operations first on all sets belonging to
a given way (looping through sets) and then decrementing the way.
Benchmarks showed that by swapping the ordering in which sets and
ways are decremented in the v7 cache flushing routine, that uses
set/way operations, time required to flush caches is reduced
significantly, owing to improved writebacks throughput to the DRAM
controller.
Benchmarks results vary and depend heavily on the last level of
cache tag RAM content when cache is cleaned and invalidated, ranging
from 2x throughput when all tag RAM entries contain dirty lines
mapping to sequential pages of RAM to 1x (ie no improvement) when
all tag RAM accesses trigger a DRAM precharge/activate cycle, as the
current code implies on most DRAM controller configurations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / karo-tx-linux.git / log