Shannon Nelson [Fri, 18 Mar 2016 19:18:15 +0000 (12:18 -0700)]
i40e: Request PHY media event at reset time
Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 18 Mar 2016 19:18:14 +0000 (12:18 -0700)]
i40e: Lower some message levels
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Fri, 18 Mar 2016 19:18:11 +0000 (12:18 -0700)]
i40e: Disable link polling
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 18 Mar 2016 19:18:10 +0000 (12:18 -0700)]
i40evf: Add longer wait after remove module
Upon module remove, wait a little longer after requesting a reset before
checking to see if the firmware responded. This change prevents double
resets when the firmware is busy.
Change-ID: Ieedc988ee82fac1f32a074bf4d9e4dba426bfa58 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 18 Mar 2016 19:18:09 +0000 (12:18 -0700)]
i40e: Make VF resets more reliable
Clear the VFLR bit immediately after triggering a reset instead of
waiting until after cleanup is complete. Make sure to trigger a reset
every time, not just if the PF is up.
These changes fix a problem where VF resets would get lost by the PF,
preventing the VF driver from initializing.
Change-ID: I5945cf2884095b7b0554867c64df8617e71d9d29 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 18 Mar 2016 19:18:07 +0000 (12:18 -0700)]
i40evf: Fix VLAN features
Users of ethtool were being given the mistaken impression that this
driver was able to change its VLAN tagging features, and were
disappointed that this was not actually the case. Implement
ndo_fix_features method so that we can adjust these flags as needed to
avoid false impressions.
Change-ID: I08584f103a4fa73d6a4128d472e4ef44dcfda57f Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Fri, 18 Mar 2016 19:18:06 +0000 (12:18 -0700)]
i40e: Remove unused variable
This variable is vestigial, a remnant of the primordial code from which
this driver spawned. We can safely remove it.
Change-ID: I24e0fe338e7c7c50d27dc5515564f33caefbb93a Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin King [Sat, 13 Feb 2016 23:57:16 +0000 (23:57 +0000)]
i40e: remove redundant check on vsi->active_vlans
active_vlans is an unsigned long array, hence a null check on this
array is superfluous and can be removed.
Detected with static analysis by smatch:
drivers/net/ethernet/intel/i40e/i40e_debugfs.c:386
i40e_dbg_dump_vsi_seid() warn: this array is probably
non-NULL. 'vsi->active_vlans'
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When signaling that a GRO frame is ready to be processed, the network stack
correctly checks length and aborts processing when a frame is less than 14
bytes. However, such a condition is really indicative of a broken driver,
and should be loudly signaled, rather than silently dropped as the case is
today.
Convert the condition to use net_warn_ratelimited() to ensure the stack
loudly complains about such broken drivers.
Signed-off-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 1 Apr 2016 22:20:35 +0000 (17:20 -0500)]
ibmvnic: enable RX checksum offload
Enable RX Checksum offload feature in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Cc: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 1 Apr 2016 22:20:34 +0000 (17:20 -0500)]
ibmvnic: map L2/L3/L4 header descriptors to firmware
Allow the VNIC driver to provide descriptors containing
L2/L3/L4 headers to firmware. This feature is needed
for greater hardware compatibility and enablement of checksum
and TCP offloading features.
A new function is included for the hypervisor call,
H_SEND_SUBCRQ_INDIRECT, allowing a DMA-mapped array of SCRQ
descriptor elements to be sent to the VNIC server.
These additions will help fully enable checksum offloading as
well as other features as they are included later.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Cc: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Tue, 5 Apr 2016 21:00:01 +0000 (14:00 -0700)]
net: bcmgenet: cleanup for dmadesc_set()
dmadesc_set() is used for setting the Tx buffer DMA address, length,
and status bits on a Tx ring descriptor when a frame is being Tx'ed.
Always set the Tx buffer DMA address first, before updating the length
and status bits, i.e. giving the Tx descriptor to the hardware.
The reason this is a cleanup rather than a fix is that the hardware
won't transmit anything from a Tx ring until the TDMA producer index
has been incremented. As long as the dmadesc_set() writes complete
before the TDMA producer index write, life is good.
Signed-off-by: Petri Gynther <pgynther@google.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Tue, 5 Apr 2016 21:00:00 +0000 (14:00 -0700)]
net: bcmgenet: cleanup for bcmgenet_xmit_frag()
Add frag_size = skb_frag_size(frag) and use it when needed.
Signed-off-by: Petri Gynther <pgynther@google.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Tue, 5 Apr 2016 20:59:59 +0000 (13:59 -0700)]
net: bcmgenet: cleanup for bcmgenet_xmit()
1. Readability: Move nr_frags assignment a few lines down in order
to bundle index -> ring -> txq calculations together.
2. Readability: Add parentheses around nr_frags + 1.
3. Minor fix: Stop the Tx queue and throw the error message only if
the Tx queue hasn't already been stopped.
Signed-off-by: Petri Gynther <pgynther@google.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Apr 2016 20:29:38 +0000 (16:29 -0400)]
Merge branch 'udp-peek'
Willem de Bruijn says:
====================
udp: support SO_PEEK_OFF
Support peeking at a non-zero offset for UDP sockets. Match the
existing behavior on Unix datagram sockets.
1/3 makes the sk_peek_offset functions safe to use outside locks
2/3 removes udp headers before enqueue, to simplify offset arithmetic
3/3 introduces SO_PEEK_OFFSET support, with Unix socket peek semantics.
Changes
v1->v2
- squash patches 3 and 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable peeking at UDP datagrams at the offset specified with socket
option SOL_SOCKET/SO_PEEK_OFF. Peek at any datagram in the queue, up
to the end of the given datagram.
Implement the SO_PEEK_OFF semantics introduced in commit ef64a54f6e55
("sock: Introduce the SO_PEEK_OFF sock option"). Increase the offset
on peek, decrease it on regular reads.
When peeking, always checksum the packet immediately, to avoid
recomputation on subsequent peeks and final read.
The socket lock is not held for the duration of udp_recvmsg, so
peek and read operations can run concurrently. Only the last store
to sk_peek_off is preserved.
Signed-off-by: Sam Kumar <samanthakumar@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
udp: remove headers from UDP packets before queueing
Remove UDP transport headers before queueing packets for reception.
This change simplifies a follow-up patch to add MSG_PEEK support.
Signed-off-by: Sam Kumar <samanthakumar@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sock: convert sk_peek_offset functions to WRITE_ONCE
Make the peek offset interface safe to use in lockless environments.
Use READ_ONCE and WRITE_ONCE to avoid race conditions between testing
and updating the peek offset.
Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Apr 2016 20:26:31 +0000 (16:26 -0400)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to i40e and i40evf only.
Stefan converts dev_close() to ndo_stop() for ethtool offline self test,
since dev_close() causes IFF_UP to be cleared which will remove the
interface routes and addresses.
Alex bumps up the size of the transmit data buffer to 12K rather than 8K,
which provides a gain in throughput and a reduction in overhead for
putting together the frame. Fixed an issue in the polling routines where
we were using bitwise operators to avoid the side effects of the
logical operators. Then added support for bulk transmit clean for skbs.
Jesse fixed a sparse issue in the type casting in the transmit code and
fixed i40e_aq_set_phy_debug() to use i40e_status as a return code.
Catherine cleans up duplicated code.
Shannon fixed the cleaning up of the interrupt handling to clean up the
IRQs only if we actually got them set up. Also fixed up the error
scenarios where we were trying to remove a non-existent timer or
worktask, which causes the kernel heartburn.
Mitch changes the notification of resets to the reset interrupt handler,
instead of the actual reset initiation code. This allows the VFs to get
properly notified for all resets, including resets initiated by different
PFs on the same physical device. Also moved the clearing of VFLR bit
after reset processing, instead of before which could lead to double
resets on VF init. Fixed code comment to match the actual function name.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 5 Apr 2016 18:09:03 +0000 (14:09 -0400)]
bnxt_en: Improve ethtool .get_settings().
If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings. The
unknown speed and duplex should only be used for autoneg when link is
down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 5 Apr 2016 18:09:01 +0000 (14:09 -0400)]
bnxt_en: Add unsupported SFP+ module warnings.
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver
will print an appropriate warning to reflect the SFP+ module enforcement
policy done in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 5 Apr 2016 18:09:00 +0000 (14:09 -0400)]
bnxt_en: Set async event bits when registering with the firmware.
Currently, the driver only sets bit 0 of the async_event_fwd fields.
To be compatible with the latest spec, we need to set the
appropriate event bits handled by the driver. We should be handling
link change and PF driver unload events, so these 2 bits should be
set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 5 Apr 2016 18:08:58 +0000 (14:08 -0400)]
bnxt_en: Add EEE setup code.
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 5 Apr 2016 18:08:56 +0000 (14:08 -0400)]
bnxt_en: Improve flow control autoneg with Firmware 1.2.1 interface.
Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Apr 2016 20:08:02 +0000 (16:08 -0400)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to fm10k only.
Bruce provides nearly half of the patches in the series, most of which do
general cleanup of the driver. These include semantic cleanups,
checkpatch.pl fixes, update driver to use BIT() kernel macro, use
BUILD_BUG_ON() where appropriate and use ether_addr_copy() instead of
memcpy().
Jake provides the remaining patches in the series, starting with a fix
for a possible NULL pointer deference. Next delays initialization of the
service timer and service task until late in probe(). If we do not wait,
failures in probe do not properly cleanup the service timer or service
task items which result in a kernel panic. Added better reporting during
error conditions. Fixed another possible kernel panic where we were
clearing the interrupt scheme before we freed the mailbox IRQ. Added
helper functions for setting strings and data for ethtool stats. Fixed
comment mis-spelled words.
v2: Dropped patch 3 from the original submission, until a better solution
can be worked up based on feedback from Joe Perches and David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 17 Feb 2016 00:19:24 +0000 (16:19 -0800)]
fm10k: use ethtool_rxfh_indir_default for default redirection table
The fm10k driver used its own code for generating a default indirection
table on device load, which was not the same as the default generated by
ethtool when indir_size of 0 is passed to SRXFH. Take advantage of
ethtool_rxfh_indir_default() and simplify code to write the redirection
table to reduce some code duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 10 Feb 2016 22:45:50 +0000 (14:45 -0800)]
fm10k: correctly clean up when init_queueing_scheme fails
Fix a kernel panic that occurs during surprise removal. Clear the
interface queue counts upon fm10k_init_msix_capability failure. This
prevents further code (fm10k_update_stats etc.) from attempting to
access unallocated queue vector or ring memory.
Bruce Allan [Wed, 10 Feb 2016 22:45:47 +0000 (14:45 -0800)]
fm10k: prevent possibly uninitialized variable
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err
will be used uninitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Fri, 5 Feb 2016 18:43:08 +0000 (10:43 -0800)]
fm10k: add helper functions to set strings and data for ethtool stats
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability. Skip handling of the per-queue stats as these will be
reworked in a following patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 4 Feb 2016 18:47:58 +0000 (10:47 -0800)]
fm10k: free MBX IRQ before clearing interrupt scheme
During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 4 Feb 2016 18:47:57 +0000 (10:47 -0800)]
fm10k: print error message when stop_hw fails
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 4 Feb 2016 18:47:56 +0000 (10:47 -0800)]
fm10k: base queue scheme covered by RSS
In fm10k_set_num_queues, we previously assigned the base template. This
would always be overwritten by either fm10k_set_qos_queues or
fm10k_set_rss_queues. In either case, we don't need the base values, so
we can just remove them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 4 Feb 2016 18:47:55 +0000 (10:47 -0800)]
fm10k: don't initialize service task until later in probe
Delay initialization of the service timer and service task until late
probe. If we don't wait, failures in probe do not properly cleanup the
service timer or service task items, which results in the kernel panic
below, potentially freezing the whole system. In addition, ensure that
the SERVICE_DISABLE bit is set before we request the MBX IRQ since the
MBX interrupt attempts to schedule the service task otherwise. This
prevents a similar trace from occurring after this change.
We didn't notice this issue before because probe almost always completes
successfully. I discovered it due to a mis-ordered mailbox handler
array, which resulted in the following failure when requesting mailbox
interrupt.
Jacob Keller [Thu, 4 Feb 2016 18:47:54 +0000 (10:47 -0800)]
fm10k: prevent null pointer dereference of msix_entries table
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 29 Dec 2015 02:00:30 +0000 (18:00 -0800)]
fm10k: use ether_addr_copy to copy MAC address
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 22 Dec 2015 22:55:20 +0000 (14:55 -0800)]
fm10k: demote BUG_ON() to WARN_ON() where appropriate
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 22 Dec 2015 21:43:49 +0000 (13:43 -0800)]
fm10k: cleanup remaining right-bit-shifted 1
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 22 Dec 2015 21:43:44 +0000 (13:43 -0800)]
fm10k: Move constants to the right of binary operators
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 10 Mar 2016 22:59:50 +0000 (14:59 -0800)]
i40e: Change comment to reflect correct function name
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 10 Mar 2016 22:59:49 +0000 (14:59 -0800)]
i40evf: Add additional check for reset
If the driver happens to read a register during the time in which the
device is undergoing reset, it will receive a value of 0xdeadbeef
instead of a valid value. Unfortunately, the driver may misinterpret
this as a valid value, especially if it's just looking for individual
bits.
Add an explicit check for this value when we are looking for admin queue
errors, and trigger reset recovery if we find it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 10 Mar 2016 22:59:48 +0000 (14:59 -0800)]
i40e: Change unknown event error msg to ignore message
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 10 Mar 2016 22:59:47 +0000 (14:59 -0800)]
i40e: Added code to prevent double resets
Clear the VFLR bit after reset processing, instead of before. This
prevents double resets on VF init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 10 Mar 2016 22:59:46 +0000 (14:59 -0800)]
i40e: Notify VFs of all resets
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 10 Mar 2016 22:59:45 +0000 (14:59 -0800)]
i40e: Remove timer and task only if created
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 5 Apr 2016 19:07:55 +0000 (15:07 -0400)]
Merge branch 'mlxsw-next'
Jiri Pirko says:
====================
mlxsw: small driver update, including switchdev doc update
Ido Schimmel (3):
mlxsw: spectrum: Reduce number of supported 802.1D bridges
switchdev: Use switch ID in suggested udev rule
mlxsw: spectrum: Add support for physical port names
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add support for physical port names
Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used:
1) Non-split: pX
2) Split: pXsY
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since there can be multiple switch ASICs on the same system we should
use the switch ID in order to differentiate between them and set the
switch name (e.g. swX) accordingly.
Also, replace the order of the "Switch ID" and "Port Netdev Naming"
sections following the above change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Reduce number of supported 802.1D bridges
Resources allocated for these bridges at init time cannot be later used
for other purposes. While current number is supported by the device,
it's mostly theoretical with regards to any real use case, which leads
to poor utilization of device's resources. Solve that by reducing the
number.
The long term plan is to make this value (along with others) user
configurable via devlink and write it to NVRAM, so that it can be used
during the next init. Until then we must hardcode such values.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Thu, 10 Mar 2016 22:59:44 +0000 (14:59 -0800)]
i40e: Assure that adminq is alive in debug mode
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 10 Mar 2016 22:59:43 +0000 (14:59 -0800)]
i40e: Remove MSIx only if created
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kevin Scott [Thu, 10 Mar 2016 22:59:41 +0000 (14:59 -0800)]
i40e: Save off VSI resource count when updating VSI
When updating a VSI, save off the number of allocated and unallocated
VSIs as we do when adding a VSI.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 7 Mar 2016 17:30:03 +0000 (09:30 -0800)]
i40e/i40evf: Add support for bulk free in Tx cleanup
This patch enables bulk Tx clean for skbs. In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0. In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 7 Mar 2016 17:29:57 +0000 (09:29 -0800)]
i40e/i40evf: Fix handling of boolean logic in polling routines
In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case. This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.
Fixes: 1a36d7fadd14 ("i40e/i40evf: use logical operators, not bitwise") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Cox [Wed, 2 Mar 2016 00:02:15 +0000 (16:02 -0800)]
i40evf: remove dead code
The only error case is when the malloc fails, in which case the clean up
loop does nothing at all, so remove it
Signed-off-by: Alan Cox <alan@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 19 Feb 2016 20:17:08 +0000 (12:17 -0800)]
i40e/i40evf: Allow up to 12K bytes of data per Tx descriptor instead of 8K
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Wed, 3 Feb 2016 08:20:47 +0000 (09:20 +0100)]
i40e: call ndo_stop() instead of dev_close() when running offline selftest
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 5 Apr 2016 02:11:21 +0000 (22:11 -0400)]
Merge branch 'tcp-udp-misc'
Eric Dumazet says:
====================
net: various udp/tcp changes
First round of patches for linux-4.7
Add a generic facility for sockets to be freed after an RCU grace
period, if they need to.
Then UDP stack is changed to no longer use SLAB_DESTROY_BY_RCU,
in order to speedup rx processing for traffic encapsulated in UDP.
It gives a 17 % speedup for normal UDP reception in stress conditions.
Then TCP listeners are changed to use SOCK_RCU_FREE as well
to avoid touching sk_refcnt in synflood case :
I got up to 30 % performance increase for a mono listener.
Then three patches add SK_MEMINFO_DROPS to sock_diag
and add per socket rx drops accounting to TCP.
Last patch adds rate limiting on ACK sent on behalf of SYN_RECV
to better resist to SYNFLOOD targeting one or few flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:22 +0000 (08:52 -0700)]
tcp: rate limit ACK sent by SYN_RECV request sockets
Attackers like to use SYNFLOOD targeting one 5-tuple, as they
hit a single RX queue (and cpu) on the victim.
If they use random sequence numbers in their SYN, we detect
they do not match the expected window and send back an ACK.
This patch adds a rate limitation, so that the effect of such
attacks is limited to ingress only.
We roughly double our ability to absorb such attacks.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Maciej Żenczykowski <maze@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:21 +0000 (08:52 -0700)]
ipv4: tcp: set SOCK_USE_WRITE_QUEUE for ip_send_unicast_reply()
TCP uses per cpu 'sockets' to send some packets :
- RST packets ( tcp_v4_send_reset()) )
- ACK packets for SYN_RECV and TIMEWAIT sockets
By setting SOCK_USE_WRITE_QUEUE flag, we tell sock_wfree()
to not call sk_write_space() since these internal sockets
do not care.
This gives a small performance improvement, merely by allowing
cpu to properly predict the sock_wfree() conditional branch,
and avoiding one atomic operation.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:20 +0000 (08:52 -0700)]
tcp: increment sk_drops for listeners
Goal: packets dropped by a listener are accounted for.
This adds tcp_listendrop() helper, and clears sk_drops in sk_clone_lock()
so that children do not inherit their parent drop count.
Note that we no longer increment LINUX_MIB_LISTENDROPS counter when
sending a SYNCOOKIE, since the SYN packet generated a SYNACK.
We already have a separate LINUX_MIB_SYNCOOKIESSENT
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:19 +0000 (08:52 -0700)]
tcp: increment sk_drops for dropped rx packets
Now ss can report sk_drops, we can instruct TCP to increment
this per socket counter when it drops an incoming frame, to refine
monitoring and debugging.
Following patch takes care of listeners drops.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:18 +0000 (08:52 -0700)]
sock_diag: add SK_MEMINFO_DROPS
Reporting sk_drops to user space was available for UDP
sockets using /proc interface.
Add this to sock_diag, so that we can have the same information
available to ss users, and we'll be able to add sk_drops
indications for TCP sockets as well.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:16 +0000 (08:52 -0700)]
inet: reqsk_alloc() needs to take care of dead listeners
We'll soon no longer take a refcount on listeners,
so reqsk_alloc() can not assume a listener refcount is not
zero. We need to use atomic_inc_not_zero()
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:15 +0000 (08:52 -0700)]
tcp/dccp: use rcu locking in inet_diag_find_one_icsk()
RX packet processing holds rcu_read_lock(), so we can remove
pairs of rcu_read_lock()/rcu_read_unlock() in lookup functions
if inet_diag also holds rcu before calling them.
This is needed anyway as __inet_lookup_listener() and
inet6_lookup_listener() will soon no longer increment
refcount on the found listener.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:13 +0000 (08:52 -0700)]
udp: no longer use SLAB_DESTROY_BY_RCU
Tom Herbert would like not touching UDP socket refcnt for encapsulated
traffic. For this to happen, we need to use normal RCU rules, with a grace
period before freeing a socket. UDP sockets are not short lived in the
high usage case, so the added cost of call_rcu() should not be a concern.
This actually removes a lot of complexity in UDP stack.
Multicast receives no longer need to hold a bucket spinlock.
Note that ip early demux still needs to take a reference on the socket.
Same remark for functions used by xt_socket and xt_PROXY netfilter modules,
but this might be changed later.
Performance for a single UDP socket receiving flood traffic from
many RX queues/cpus.
Simple udp_rx using simple recvfrom() loop :
438 kpps instead of 374 kpps : 17 % increase of the peak rate.
v2: Addressed Willem de Bruijn feedback in multicast handling
- keep early demux break in __udp4_lib_demux_lookup()
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@herbertland.com> Cc: Willem de Bruijn <willemb@google.com> Tested-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Apr 2016 15:52:12 +0000 (08:52 -0700)]
net: add SOCK_RCU_FREE socket flag
We want a generic way to insert an RCU grace period before socket
freeing for cases where RCU_SLAB_DESTROY_BY_RCU is adding too
much overhead.
SLAB_DESTROY_BY_RCU strict rules force us to take a reference
on the socket sk_refcnt, and it is a performance problem for UDP
encapsulation, or TCP synflood behavior, as many CPUs might
attempt the atomic operations on a shared sk_refcnt
UDP sockets and TCP listeners can set SOCK_RCU_FREE so that their
lookup can use traditional RCU rules, without refcount changes.
They can set the flag only once hashed and visible by other cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <tom@herbertland.com> Tested-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Apr 2016 02:01:44 +0000 (22:01 -0400)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-04-04
This series contains updates to ixgbe and ixgbevf.
Pavel Tikhomirov fixes a typo where we were incrementing transmit stats
instead of receive stats on the receive side.
Emil updates the ixgbevf driver to use bit operations for setting and
checking the adapter state.
Chas Williams adds the new NDO trust feature check so that the VF guest
has the ability to set the unicast address of the interface, if it is a
trusted VF.
Alex cleans up the driver to that the only time we add a PF entry to the
VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using. Also adds support for generic transmit checksums,
giving the added advantage is that we can support inner checksum offloads
for tunnels and MPLS while still being able to transparently insert
VLAN tags. Lastly, changed ixgbe so that we can use the ethtool
rx-vlan-filter flag to toggle receive VLAN filtering on and off.
Mark cleans up the ixgbe driver by making all op structures that do not
change constants. Also fixed flow control for Xeon D KR backplanes, since
we cannot use auto-negotiation to determine the mode, we have to use
whatever the user configured.
Sowmini Varadhan updates ixgbe to use eth_platform_get_mac_address()
instead of the arch specific solution that was added by a previous
commit.
Don fixed an issue where it was possible that a system reset could occur
when we were holding the SWFW semaphore lock, which the next time the
driver loaded would see it incorrectly as locked.
v2: updated patch 8 of the series to include a minor flags issue where
we had lost NETIF_F_HW_TC and we were setting NETIF_F_SCTP_CRC in
two different areas, when we only needed/wanted it in one spot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Apr 2016 01:31:35 +0000 (21:31 -0400)]
Merge branch 'mv88e6131-hw-bridging-6185'
Vivien Didelot says:
====================
net: dsa: mv88e6131: HW bridging support for 6185
All packets passing through a switch of the 6185 family are currently all
directed to the CPU port. This means that port bridging is software driven.
To enable hardware bridging for this switch family, we need to implement the
port mapping operations, the FDB operations, and optionally the VLAN operations
(for 802.1Q and VLAN filtering aware systems).
However this family only has 256 FDBs indexed by 8-bit identifiers, opposed to
4096 FDBs with 12-bit identifiers for other families such as 6352. It also
doesn't have dedicated FID registers for ATU and VTU operations.
This patchset fixes these differences, and enable hardware bridging for 6185.
Changes v1 -> v2:
- Describe the different numbers of databases and prefer a feature-based logic
over the current ID/family-based logic.
====================
Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 31 Mar 2016 20:53:46 +0000 (16:53 -0400)]
net: dsa: mv88e6131: enable hardware bridging
By adding support for bridge operations, FDB operations, and optionally
VLAN operations (for 802.1Q and VLAN filtering aware systems), the
switch bridges ports correctly, the CPU is able to populate the hardware
address databases, and thus hardware bridging becomes functional within
the 88E6185 family of switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 31 Mar 2016 20:53:44 +0000 (16:53 -0400)]
net: dsa: mv88e6xxx: support 256 databases
The 6185 family of devices has only 256 address databases. Their 8-bit
FID for ATU and VTU operations are split into ATU Control and ATU/VTU
Operation registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 31 Mar 2016 20:53:43 +0000 (16:53 -0400)]
net: dsa: mv88e6xxx: variable number of databases
Marvell switch chips have different number of address databases.
The code currently only supports models with 4096 databases. Such switch
has dedicated FID registers for ATU and VTU operations. Models with
fewer databases have their FID split in several registers.
List them all but only support models with 4096 databases at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Thu, 31 Mar 2016 20:53:42 +0000 (16:53 -0400)]
net: dsa: mv88e6xxx: protect FID registers access
Only switch families with 4096 address databases have dedicated FID
registers for ATU and VTU operations.
Factorize the access to the GLOBAL_ATU_FID register and introduce a
mv88e6xxx_has_fid_reg() helper function to protect the access to
GLOBAL_ATU_FID and GLOBAL_VTU_FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 10 Mar 2016 18:01:10 +0000 (10:01 -0800)]
ixgbe: Add support for toggling VLAN filtering flag via ethtool
This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off. This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Amritha Nambiar [Wed, 9 Mar 2016 23:32:16 +0000 (18:32 -0500)]
ixgbe: Extend cls_u32 offload to support UDP headers
Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.
Verified with the following filters :
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
u32 ht 1: order 2 \
match tcp src 1024 ffff match tcp dst 23 ffff action drop
handle 2: u32 divisor 1
u32 ht 800: order 3 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
u32 ht 2: order 4 \
match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 9 Mar 2016 21:45:00 +0000 (16:45 -0500)]
ixgbe: Place SWFW semaphore in known valid state at probe
It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock. So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe: add a callback to set the maximum transmit bitrate
This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.
Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 26 Jan 2016 00:32:10 +0000 (16:32 -0800)]
ixgbe: Fix flow control for Xeon D KR backplane
Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 13 Jan 2016 15:31:17 +0000 (07:31 -0800)]
ixgbevf: Add support for generic Tx checksums
This patch adds support for generic Tx checksums to the ixgbevf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 13 Jan 2016 15:31:11 +0000 (07:31 -0800)]
ixgbe: Add support for generic Tx checksums
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sowmini Varadhan [Wed, 13 Jan 2016 03:32:30 +0000 (19:32 -0800)]
ixgbe: use eth_platform_get_mac_address()
This commit converts commit c762dff24c06 ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d105495a ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / linux-beck.git / log