Drivers should be including <linux/io.h> instead of <asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Alistair John Strachan <alistair@devzero.co.uk> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Juerg Haefliger <juergh@gmail.com> Cc: Frank Seidel <frank@f-seidel.de> Acked-by: Jim Cromie <jim.cromie@gmail.com> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Roger Lucas <vt8231@hiddenengine.co.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Andre Prendel [Tue, 15 Sep 2009 15:18:11 +0000 (17:18 +0200)]
hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips
Add support for Texas Instruments TMP421/422/423 temperature sensor IC.
TI's TMP421/422/423 are I2C temperature sensor chips. These chips are
similar to TI's TMP401/411 chips, but with reduced functionality (only
temperature measurement). The chips have one local sensor and up to
three (TMP423) remote sensors.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 15 Sep 2009 15:18:11 +0000 (17:18 +0200)]
hwmon-vid: Ignore 6th VID pin of AMD family 0Fh processors
We had a report about a mainboard for AMD family 0Fh processors not
routing the 6th VID pin from the CPU to the hardware monitoring chip.
While the vendor should have wired the pin (or, failing that, should
have hardwired it to level high rather than low), the fact is that
none of these processors are currently known to operate at the lower
voltage levels which require the 6th VID pin. So, as a practical
workaround, I propose to ignore the 6th VID pin for these CPUs.
If this decision ever causes problems, we'll reconsider.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Frank Myhr <fmyhr@fhmtech.com> Tested-by: Hleb Valoshka <375gnu@gmail.com> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
hwmon: (abituguru3) Support multiple DMI strings per chip ID
Most known Abit motherboards have unique uguru chip IDs. However,
some "refresh" boards keep the same chip ID but have a different
DMI string. As our DMI board string matching is (necessarily)
strict, some boards were failing DMI detection, and as the old
probe method was also failing, the driver would not load.
The only known boards affected by this problem are the IP35 Pro XE
(vs IP35 Pro) and the AB9 Pro (vs AB9). Is it not sufficient to
relax the match criteria, as some boards (e.g. the AB9 Quad GT)
have different uguru chip IDs.
This patch replaces the dmi_name string with a NULL terminated
array of strings to be matched per uguru chip ID. It has been
compile and runtime tested (thanks Rune).
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Rune Svendsen <runesvend@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Merge branch 'for-linus3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
SELinux: inline selinux_is_enabled in !CONFIG_SECURITY_SELINUX
KEYS: Fix garbage collector
KEYS: Unlock tasklist when exiting early from keyctl_session_to_parent
CRED: Allow put_cred() to cope with a NULL groups list
SELinux: flush the avc before disabling SELinux
SELinux: seperate avc_cache flushing
Creds: creds->security can be NULL is selinux is disabled
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (23 commits)
at_hdmac: Rework suspend_late()/resume_early()
PM: Reset transition_started at dpm_resume_noirq
PM: Update kerneldoc comments in drivers/base/power/main.c
PM: Add convenience macro to make switching to dev_pm_ops less error-prone
hp-wmi: Switch driver to dev_pm_ops
floppy: Switch driver to dev_pm_ops
PM: Trivial fixes
PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
PM/Hibernate: Rework shrinking of memory
PM: Fix typo in label name s/Platofrm_finish/Platform_finish/
PM: Run-time PM platform device bus support
PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
Driver Core: Make PM operations a const pointer
PM: Remove platform device suspend_late()/resume_early() V2
USB: Rework musb suspend()/resume_early()
I2C: Rework i2c-s3c2410 suspend_late()/resume() V2
I2C: Rework i2c-pxa suspend_late()/resume_early()
DMA: Rework txx9dmac suspend_late()/resume_early()
...
Fix trivial conflict in drivers/base/platform.c (due to same
constification patch being merged in both sides, along with some other
PM work in the PM branch)
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig:
kconfig: add missing dependency of conf to localyesconfig
kconfig: test if a .config already exists
kconfig: make local .config default for streamline_config
kconfig: test for /boot/config-uname after /proc/config.gz in localconfig
kconfig: unset IKCONFIG_PROC and clean up nesting
kconfig: search for a config to base the local(mod|yes)config on
kconfig: keep config.gz around even if CONFIG_IKCONFIG_PROC is not set
kconfig: have extract-ikconfig read ELF files
kconfig: add check if end exists in extract-ikconfig
kconfig: enable CONFIG_IKCONFIG from streamline_config.pl
kconfig: do not warn about modules built in
kconfig: streamline_config.pl do not stop with no depends
kconfig: add make localyesconfig option
kconfig: make localmodconfig to run streamline_config.pl
kconfig: add streamline_config.pl to scripts
Eric Paris [Tue, 15 Sep 2009 00:59:48 +0000 (20:59 -0400)]
SELinux: inline selinux_is_enabled in !CONFIG_SECURITY_SELINUX
Without this patch building a kernel emits millions of warning like:
include/linux/selinux.h:92: warning: ?selinux_is_enabled? defined but not used
When it is build without CONFIG_SECURITY_SELINUX. This is harmless, but
the function should be inlined, so it gets compiled out.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: completely remove apple mightymouse from blacklist
HID: support larger reports than 64 bytes in hiddev
HID: local function should be static
HID: ignore Philips IEEE802.15.4 RF Dongle
HID: ignore all recent SoundGraph iMON devices
HID: fix memory leak on error patch in debug code
HID: fix overrun in quirks initialization
HID: Drop NULL test on list_entry result
HID: driver for Twinhan USB 6253:0100 remote control
HID: adding __init/__exit macros to module init/exit functions
HID: add rumble support for Thrustmaster Dual Trigger 3-in-1
HID: ntrig tool separation and pen usages
HID: Avoid double spin_lock_init on usbhid->lock
HID: add force feedback support for Logitech WingMan Formula Force GP
HID: Support new variants of Samsung USB IR receiver (0419:0001)
HID: fix memory leak on error path in debug code
HID: fix debugfs build with !CONFIG_DEBUG_FS
HID: use debugfs for events/reports dumping
HID: use debugfs for report dumping descriptor
Merge branch 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.32' of git://git.kernel.dk/linux-2.6-block: (29 commits)
block: use blkdev_issue_discard in blk_ioctl_discard
Make DISCARD_BARRIER and DISCARD_NOBARRIER writes instead of reads
block: don't assume device has a request list backing in nr_requests store
block: Optimal I/O limit wrapper
cfq: choose a new next_req when a request is dispatched
Seperate read and write statistics of in_flight requests
aoe: end barrier bios with EOPNOTSUPP
block: trace bio queueing trial only when it occurs
block: enable rq CPU completion affinity by default
cfq: fix the log message after dispatched a request
block: use printk_once
cciss: memory leak in cciss_init_one()
splice: update mtime and atime on files
block: make blk_iopoll_prep_sched() follow normal 0/1 return convention
cfq-iosched: get rid of must_alloc flag
block: use interrupts disabled version of raise_softirq_irqoff()
block: fix comment in blk-iopoll.c
block: adjust default budget for blk-iopoll
block: fix long lines in block/blk-iopoll.c
block: add blk-iopoll, a NAPI like approach for block devices
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
[SCSI] fix oops during scsi scanning
[SCSI] libsrp: fix memory leak in srp_ring_free()
[SCSI] libiscsi, bnx2i: make bound ep check common
[SCSI] libiscsi: add completion function for drivers that do not need pdu processing
[SCSI] scsi_dh_rdac: changes for rdac debug logging
[SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
[SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
[SCSI] sg: fix oops in the error path in sg_build_indirect()
[SCSI] mptsas : Bump version to 3.04.12
[SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
[SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
[SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
[SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
[SCSI] mptsas : Sanity check for phyinfo is added
[SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
[SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
[SCSI] qla2xxx: Update version number to 8.03.01-k6.
[SCSI] qla2xxx: Properly delete rports attached to a vport.
[SCSI] qla2xxx: Correct various NPIV issues.
[SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
...
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
My 353d5c30c666580347515da609dd74a2b8e9b828 "mm: fix hugetlb bug due to
user_shm_unlock call" broke the CONFIG_SYSVIPC !CONFIG_MMU build of both
2.6.31 and 2.6.30.6: "undefined reference to `user_shm_unlock'".
gcc didn't understand my comment! so couldn't figure out to optimize
away user_shm_unlock() from the error path in the hugetlb-less case, as
it does elsewhere. Help it to do so, in a language it understands.
Merge branch 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
console_print() is an old legacy interface mostly unused in the entire
kernel tree. It's best to clean up its existing use and let developers
use their own implementation of it as they feel fit.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: fix slab_pad_check()
slub: release kobject if sysfs_create_group failed in sysfs_slab_add
SLUB: fix ARCH_KMALLOC_MINALIGN cases 64 and 256
SLUB: Fix some coding style issues
SLUB: Drop write permission to /proc/slabinfo
slab: remove duplicate kmem_cache_init_late() declarations
slub: change kmem_cache->align to record the real alignment
slub: use size and objsize orders to disable debug flags
slub: add option to disable higher order debugging slabs
David Howells [Mon, 14 Sep 2009 16:26:13 +0000 (17:26 +0100)]
KEYS: Fix garbage collector
Fix a number of problems with the new key garbage collector:
(1) A rogue semicolon in keyring_gc() was causing the initial count of dead
keys to be miscalculated.
(2) A missing return in keyring_gc() meant that under certain circumstances,
the keyring semaphore would be unlocked twice.
(3) The key serial tree iterator (key_garbage_collector()) part of the garbage
collector has been modified to:
(a) Complete each scan of the keyrings before setting the new timer.
(b) Only set the new timer for keys that have yet to expire. This means
that the new timer is now calculated correctly, and the gc doesn't
get into a loop continually scanning for keys that have expired, and
preventing other things from happening, like RCU cleaning up the old
keyring contents.
(c) Perform an extra scan if any keys were garbage collected in this one
as a key might become garbage during a scan, and (b) could mean we
don't set the timer again.
(4) Made key_schedule_gc() take the time at which to do a collection run,
rather than the time at which the key expires. This means the collection
of dead keys (key type unregistered) can happen immediately.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Marc Dionne [Mon, 14 Sep 2009 11:46:23 +0000 (12:46 +0100)]
KEYS: Unlock tasklist when exiting early from keyctl_session_to_parent
When we exit early from keyctl_session_to_parent because of permissions or
because the session keyring is the same as the parent, we need to unlock the
tasklist.
The missing unlock causes the system to hang completely when using
keyctl(KEYCTL_SESSION_TO_PARENT) with a keyring shared with the parent.
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
David Howells [Mon, 14 Sep 2009 11:45:39 +0000 (12:45 +0100)]
CRED: Allow put_cred() to cope with a NULL groups list
put_cred() will oops if given a NULL groups list, but that is now possible with
the existence of cred_alloc_blank(), as used in keyctl_session_to_parent().
Added in commit:
commit ee18d64c1f632043a02e6f5ba5e045bb26a5465f
Author: David Howells <dhowells@redhat.com>
Date: Wed Sep 2 09:14:21 2009 +0100
KEYS: Add a keyctl to install a process's session keyring on its parent [try #6]
Reported-by: Marc Dionne <marc.c.dionne@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Merge branch 'osync_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'osync_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
fsync: wait for data writeout completion before calling ->fsync
vfs: Remove generic_osync_inode() and sync_page_range{_nolock}()
fat: Opencode sync_page_range_nolock()
pohmelfs: Use new syncing helper
xfs: Convert sync_page_range() to simple filemap_write_and_wait_range()
ocfs2: Update syncing after splicing to match generic version
ntfs: Use new syncing helpers and update comments
ext4: Remove syncing logic from ext4_file_write
ext3: Remove syncing logic from ext3_file_write
ext2: Update comment about generic_osync_inode
vfs: Introduce new helpers for syncing after writing to O_SYNC file or IS_SYNC inode
vfs: Rename generic_file_aio_write_nolock
ocfs2: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
pohmelfs: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
vfs: Remove syncing from generic_file_direct_write() and generic_file_buffered_write()
vfs: Export __generic_file_aio_write() and add some comments
vfs: Introduce filemap_fdatawait_range
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw:
GFS2: Whitespace fixes
GFS2: Remove unused sysfs file
GFS2: Be extra careful about deallocating inodes
GFS2: Remove no_formal_ino generating code
GFS2: Rename eattr.[ch] as xattr.[ch]
GFS2: Clean up of extended attribute support
GFS2: Add explanation of extended attr on-disk format
GFS2: Add "-o errors=panic|withdraw" mount options
GFS2: jumping to wrong label?
GFS2: free disk inode which is deleted by remote node -V2
GFS2: Add a document explaining GFS2's uevents
GFS2: Add sysfs link to device
GFS2: Replace assertion with proper error handling
GFS2: Improve error handling in inode allocation
GFS2: Add some more info to uevents
GFS2: Add online uevent to GFS2
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: Fix possible corruption when close races with write
udf: Perform preallocation only for regular files
udf: Remove wrong assignment in udf_symlink
udf: Remove dead code
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (21 commits)
fs/Kconfig: move nilfs2 outside misc filesystems
nilfs2: convert nilfs_bmap_lookup to an inline function
nilfs2: allow btree code to directly call dat operations
nilfs2: add update functions of virtual block address to dat
nilfs2: remove individual gfp constants for each metadata file
nilfs2: stop zero-fill of btree path just before free it
nilfs2: remove unused btree argument from btree functions
nilfs2: remove nilfs_dat_abort_start and nilfs_dat_abort_free
nilfs2: shorten freeze period due to GC in write operation v3
nilfs2: add more check routines in mount process
nilfs2: An unassigned variable is assigned to a never used structure member
nilfs2: use GFP_NOIO for bio_alloc instead of GFP_NOWAIT
nilfs2: stop using periodic write_super callback
nilfs2: clean up nilfs_write_super
nilfs2: fix disorder of nilfs_write_super in nilfs_sync_fs
nilfs2: remove redundant super block commit
nilfs2: implement nilfs_show_options to display mount options in /proc/mounts
nilfs2: always lookup disk block address before reading metadata block
nilfs2: use semaphore to protect pointer to a writable FS-instance
nilfs2: fix format string compile warning (ino_t)
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: consolidate reconnect logic in smb_init routines
cifs: Replace wrtPending with a real reference count
cifs: protect GlobalOplock_Q with its own spinlock
cifs: use tcon pointer in cifs_show_options
cifs: send IPv6 addr in upcall with colon delimiters
[CIFS] Fix checkpatch warnings
PATCH] cifs: fix broken mounts when a SSH tunnel is used (try #4)
[CIFS] Memory leak in ntlmv2 hash calculation
[CIFS] potential NULL dereference in parse_DFS_referrals()
Xiaotian Feng [Thu, 20 Aug 2009 18:28:33 +0000 (20:28 +0200)]
PM: Reset transition_started at dpm_resume_noirq
transition_started should be set once the preparation of devices for
a PM has started, reset before starting to resume devices. When
resuming devices, kernel calls dpm_resume_noirq then
dpm_resume_end(dpm_resume). Thus we should reset transition_started
at dpm_resume_noirq.
This patch fixes ACPI warning when resuming from suspend/hibernate:
ACPI: \_SB_.PCI0.IDE1.PRI1.MAS1 - docking
------------[ cut here ]------------
WARNING: at drivers/base/power/main.c:87 device_pm_add+0x8b/0xcc()
Hardware name: OptiPlex 760
Device: acpi
Parentless device registered during a PM transaction
[rjw: Fixed up the changelog.]
Signed-off-by: Xiaotian Feng <dfeng@redhat.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM: Update kerneldoc comments in drivers/base/power/main.c
The kerneldoc comments in drivers/base/power/main.c are generally
outdated and some of them don't describe the functions very
accurately. Update them and standardize the format to use spaces
instead of tabs.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu>
Albin Tonnerre [Wed, 5 Aug 2009 21:59:59 +0000 (23:59 +0200)]
PM: Add convenience macro to make switching to dev_pm_ops less error-prone
In a number of cases, the .suspend, .freeze, .poweroff and .resume,
.thaw, .restore functions are identical. However, they all need to be
assigned to avoid regressionsm as the previous code called .suspend
resp. .resume in all those cases. SIMPLE_DEV_PM_OPS helps to deal
with this case.
[rjw: Changed the name of the macro and added the comment explaining its
purpose.]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM / Hibernate / Memory hotplug: Always use for_each_populated_zone()
Use for_each_populated_zone() instead of for_each_zone() in hibernation
code. This fixes a bug on s390, where we allow both config options
HIBERNATION and MEMORY_HOTPLUG, so that we also have a ZONE_MOVABLE
here. We only allow hibernation if no memory hotplug operation was
performed, so in fact both features can only be used exclusively, but
this way we don't need 2 differently configured (distribution) kernels.
If we have an unpopulated ZONE_MOVABLE, we allow hibernation but run
into a BUG_ON() in memory_bm_test/set/clear_bit() because hibernation
code iterates through all zones, not only the populated zones, in
several places. For example, swsusp_free() does for_each_zone() and
then checks for pfn_valid(), which is true even if the zone is not
populated, resulting in a BUG_ON() later because the pfn cannot be
found in the memory bitmap.
Replacing all occurences of for_each_zone() in hibernation code with
for_each_populated_zone() would fix this issue.
[rjw: Rebased on top of linux-next hibernation patches.]
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
PM/Hibernate: Do not try to allocate too much memory too hard (rev. 2)
We want to avoid attempting to free too much memory too hard during
hibernation, so estimate the minimum size of the image to use as the
lower limit for preallocating memory.
The approach here is based on the (experimental) observation that we
can't free more page frames than the sum of:
Namely, if this number is subtracted from the number of saveable
pages in the system, we get a good estimate of the minimum reasonable
size of a hibernation image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Wu Fengguang <fengguang.wu@intel.com>
PM/Hibernate: Do not release preallocated memory unnecessarily (rev. 2)
Since the hibernation code is now going to use allocations of memory
to make enough room for the image, it can also use the page frames
allocated at this stage as image page frames. The low-level
hibernation code needs to be rearranged for this purpose, but it
allows us to avoid freeing a great number of pages and allocating
these same pages once again later, so it generally is worth doing.
Rework swsusp_shrink_memory() so that it calls shrink_all_memory()
just once to make some room for the image and then allocates memory
to apply more pressure to the memory management subsystem, if
necessary.
Unfortunately, we don't seem to be able to drop shrink_all_memory()
entirely just yet, because that would lead to huge performance
regressions in some test cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@ucw.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (21 commits)
sparc64: Initial niagara2 perf counter support.
sparc64: Perf counter 'nop' event is not constant.
sparc64: Provide a way to specify a perf counter overflow IRQ enable bit.
sparc64: Provide hypervisor tracing bit support for perf counters.
sparc64: Initial hw perf counter support.
sparc64: Implement a real set_perf_counter_pending().
sparc64: Use nmi_enter() and nmi_exit(), as needed.
sparc64: Provide extern decls for sparc_??u_type strings.
sparc64: Make touch_nmi_watchdog() actually work.
sparc64: Kill unnecessary cast in profile_timer_exceptions_notify().
sparc64: Manage NMI watchdog enabling like x86.
sparc: add basic support for 'perf'
sparc: convert /proc/io_map, /proc/dvma_map to seq_file
sparc, leon: sparc-leon specific SRMMU initialization and bootup fixes.
sparc,leon: Added support for AMBAPP bus.
sparc,leon: Introduce the sparc-leon CPU type.
sparc,leon: Redefine MMU register access asi if CONFIG_LEON
sparc,leon: CONFIG_SPARC_LEON option and leon specific files.
sparc64: cheaper asm/uaccess.h inclusion
SPARC: fix duplicate declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Merge branch 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: split __phys_addr out into separate file
xen: use stronger barrier after unlocking lock
xen: only enable interrupts while actually blocking for spinlock
xen: make -fstack-protector work under Xen
Jan Kara [Thu, 6 Aug 2009 22:27:27 +0000 (00:27 +0200)]
udf: Fix possible corruption when close races with write
When we close a file, we remove preallocated blocks from it. But this
truncation was not protected by i_mutex and thus it could have raced with a
write through a different fd and cause crashes or even filesystem corruption.
Jan Kara [Thu, 16 Jul 2009 16:02:25 +0000 (18:02 +0200)]
udf: Perform preallocation only for regular files
So far we preallocated blocks also for directories but that brings a
problem, when to get rid of preallocated blocks we don't need. So far
we removed them in udf_clear_inode() which has a disadvantage that
1) blocks are unavailable long after writing to a directory finished
and thus one can get out of space unnecessarily early
2) releasing blocks from udf_clear_inode is problematic because VFS
does not expect us to redirty inode there and it also slows down
memory reclaim.
So preallocate blocks only for regular files where we can drop preallocation
in udf_release_file.
EDAC, AMD: carve out decoding of MCi_STATUS ErrorCode
This is the MCE error code from the MCi_STATUS banks, bits [15:0] which
describe what type of error was encountered: GART TLB, Memory or Bus
error. The semantics of those bits are identical across all MCE banks so
decode those separately, irrespectively of MCE type.
The MCi_STATUS registers have most field definitions in common so decode
them in the general path. Do not pass ecc_type along and compute it in
__amd64_decode_bus_error instead.
Borislav Petkov [Thu, 25 Jun 2009 17:32:38 +0000 (19:32 +0200)]
EDAC: move MCE error descriptions to EDAC core
This is in preparation of adding AMD-specific MCE decoding functionality
to the EDAC core. The error decoding macros originate from the AMD64
EDAC driver albeit in a simplified and cleaned up version here.
While at it, add macros to generate the error description strings and
use them in the error type decoders directly which removes a bunch of
code and makes the decoding functions much more readable. Also, fix
strings and shorten macro names.
fsync: wait for data writeout completion before calling ->fsync
Currenly vfs_fsync(_range) first calls filemap_fdatawrite to write out
the data, the calls into ->fsync to write out the metadata and then finally
calls filemap_fdatawait to wait for the data I/O to complete. What sounds
like a clever micro-optimization actually is nast trap for many filesystems.
For many modern filesystems i_size or other inode information is only
updated on I/O completion and we need to wait for I/O to finish before
we can write out the metadata. For old fashionen filesystems that
instanciate blocks during the actual write and also update the metadata
at that point it opens up a large window were we could expose uninitialized
blocks after a crash. While a few filesystems that need it already wait
for the I/O to finish inside their ->fsync methods it is rather suboptimal
as it is done under the i_mutex and also always for the whole file instead
of just a part as we could do for O_SYNC handling.
Here is a small audit of all fsync instances in the tree:
never touch pagecache themselves. We need to wait before if we do
not want to expose stale data after an allocation.
- afs_fsync:
- fuse_fsync_common:
do the waiting writeback itself in awkward ways, would benefit from
proper semantics
- block_fsync:
Does a filemap_write_and_wait on the block device inode. Because we
now have f_mapping that is the same inode we call it on in vfs_fsync.
So just removing it and letting the VFS do the work in one go would
be an improvement.
would need the wait to work correctly for delalloc mode with late
i_size updates. Otherwise the ext3 comment applies.
currently implemens it's own writeback and wait in an odd way,
could benefit from doing it properly.
- gfs2_fsync:
not needed for journaled data mode, but probably harmless there.
Currently writes back data asynchronously itself. Needs some
major audit.
- hostfs_fsync:
just calls fsync/datasync on the host FD. Without the wait before
data might not even be inflight yet if we're unlucky.
- hpfs_file_fsync:
- ncp_fsync:
no-ops. Dangerous before and after.
- jffs2_fsync:
just calls jffs2_flush_wbuf_gc, not sure how this relates to data.
- nfs_fsync_dir:
just increments stats, claims all directory operations are synchronous
- nfs_file_fsync:
only writes out data??? Looks very odd.
- nilfs_sync_file:
looks like it expects all data done, but not sure from the code
- ntfs_dir_fsync:
- ntfs_file_fsync:
appear to do their own data writeback. Very convoluted code.
- ocfs2_sync_file:
does it's own data writeback, but no wait. probably needs the wait.
- smb_fsync:
according to a comment expects all pages written already, probably needs
the wait before.
This patch only changes vfs_fsync_range, removal of the wait in the methods
that have it is left to the filesystem maintainers. Note that most
filesystems really do need an audit for their fsync methods given the
gems found in this very brief audit.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Mon, 17 Aug 2009 15:00:02 +0000 (17:00 +0200)]
fat: Opencode sync_page_range_nolock()
fat_cont_expand() is the only user of sync_page_range_nolock(). It's also the
only user of generic_osync_inode() which does not have a file open. So
opencode needed actions for FAT so that we can convert generic_osync_inode() to
a standard syncing path.
Update a comment about generic_osync_inode().
CC: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Tue, 18 Aug 2009 16:32:55 +0000 (18:32 +0200)]
xfs: Convert sync_page_range() to simple filemap_write_and_wait_range()
Christoph Hellwig says that it is enough for XFS to call
filemap_write_and_wait_range() instead of sync_page_range() because we do
all the metadata syncing when forcing the log.
CC: Felix Blyakher <felixb@sgi.com> CC: xfs@oss.sgi.com CC: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Tue, 18 Aug 2009 16:24:31 +0000 (18:24 +0200)]
ocfs2: Update syncing after splicing to match generic version
Update ocfs2 specific splicing code to use generic syncing helper. The sync now
does not happen under rw_lock because generic_write_sync() acquires i_mutex
which ranks above rw_lock. That should not matter because standard fsync path
does not hold it either.
Acked-by: Joel Becker <Joel.Becker@oracle.com> Acked-by: Mark Fasheh <mfasheh@suse.com> CC: ocfs2-devel@oss.oracle.com Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Tue, 18 Aug 2009 16:13:58 +0000 (18:13 +0200)]
ntfs: Use new syncing helpers and update comments
Use new syncing helpers in .write and .aio_write functions. Also
remove superfluous syncing in ntfs_file_buffered_write() and update
comments about generic_osync_inode().
CC: Anton Altaparmakov <aia21@cantab.net> CC: linux-ntfs-dev@lists.sourceforge.net Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Mon, 17 Aug 2009 17:52:36 +0000 (19:52 +0200)]
vfs: Introduce new helpers for syncing after writing to O_SYNC file or IS_SYNC inode
Introduce new function for generic inode syncing (vfs_fsync_range) and use
it from fsync() path. Introduce also new helper for syncing after a sync
write (generic_write_sync) using the generic function.
Use these new helpers for syncing from generic VFS functions. This makes
O_SYNC writes to block devices acquire i_mutex for syncing. If we really
care about this, we can make block_fsync() drop the i_mutex and reacquire
it before it returns.
CC: Evgeniy Polyakov <zbr@ioremap.net> CC: ocfs2-devel@oss.oracle.com CC: Joel Becker <joel.becker@oracle.com> CC: Felix Blyakher <felixb@sgi.com> CC: xfs@oss.sgi.com CC: Anton Altaparmakov <aia21@cantab.net> CC: linux-ntfs-dev@lists.sourceforge.net CC: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> CC: linux-ext4@vger.kernel.org CC: tytso@mit.edu Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
generic_file_aio_write_nolock() is now used only by block devices and raw
character device. Filesystems should use __generic_file_aio_write() in case
generic_file_aio_write() doesn't suit them. So rename the function to
blkdev_aio_write() and move it to fs/blockdev.c.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Mon, 17 Aug 2009 16:50:08 +0000 (18:50 +0200)]
ocfs2: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
Use the new helper. We have to submit data pages ourselves in case of O_SYNC
write because __generic_file_aio_write does not do it for us. OCFS2 developpers
might think about moving the sync out of i_mutex which seems to be easily
possible but that's out of scope of this patch.
CC: ocfs2-devel@oss.oracle.com Acked-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Tue, 18 Aug 2009 14:18:20 +0000 (16:18 +0200)]
vfs: Remove syncing from generic_file_direct_write() and generic_file_buffered_write()
generic_file_direct_write() and generic_file_buffered_write() called
generic_osync_inode() if it was called on O_SYNC file or IS_SYNC inode. But
this is superfluous since generic_file_aio_write() does the syncing as well.
Also XFS and OCFS2 which call these functions directly handle syncing
themselves. So let's have a single place where syncing happens:
generic_file_aio_write().
We slightly change the behavior by syncing only the range of file to which the
write happened for buffered writes but that should be all that is required.
CC: ocfs2-devel@oss.oracle.com CC: Joel Becker <joel.becker@oracle.com> CC: Felix Blyakher <felixb@sgi.com> CC: xfs@oss.sgi.com Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Mon, 17 Aug 2009 16:10:06 +0000 (18:10 +0200)]
vfs: Export __generic_file_aio_write() and add some comments
Rename __generic_file_aio_write_nolock() to __generic_file_aio_write(), add
comments to write helpers explaining how they should be used and export
__generic_file_aio_write() since it will be used by some filesystems.
CC: ocfs2-devel@oss.oracle.com CC: Joel Becker <joel.becker@oracle.com> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
Merge branch 'x86-percpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-percpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, percpu: Collect hot percpu variables into one cacheline
x86, percpu: Fix DECLARE/DEFINE_PER_CPU_PAGE_ALIGNED()
x86, percpu: Add 'percpu_read_stable()' interface for cacheable accesses
Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, highmem_32.c: Clean up comment
x86, pgtable.h: Clean up types
x86: Clean up dump_pagetable()
Merge branch 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Simplify the Makefile in a minor way through use of cc-ifversion
Merge branch 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64: move clts into batch cpu state updates when preloading fpu
x86-64: move unlazy_fpu() into lazy cpu state part of context switch
x86-32: make sure clts is batched during context switch
x86: split out core __math_state_restore
Merge branch 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Decrease the level of some NUMA messages to KERN_DEBUG
Merge branch 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: Fix code patching for paravirt-alternatives on 486
x86, msr: change msr-reg.o to obj-y, and export its symbols
x86: Use hard_smp_processor_id() to get apic id for AMD K8 cpus
x86, sched: Workaround broken sched domain creation for AMD Magny-Cours
x86, mcheck: Use correct cpumask for shared bank4
x86, cacheinfo: Fixup L3 cache information for AMD multi-node processors
x86: Fix CPU llc_shared_map information for AMD Magny-Cours
x86, msr: Fix msr-reg.S compilation with gas 2.16.1, on 32-bit too
x86: Move kernel_fpu_using to irq_fpu_usable in asm/i387.h
x86, msr: fix msr-reg.S compilation with gas 2.16.1
x86, msr: Export the register-setting MSR functions via /dev/*/msr
x86, msr: Create _on_cpu helpers for {rw,wr}msr_safe_regs()
x86, msr: Have the _safe MSR functions return -EIO, not -EFAULT
x86, msr: CFI annotations, cleanups for msr-reg.S
x86, asm: Make _ASM_EXTABLE() usable from assembly code
x86, asm: Add 32-bit versions of the combined CFI macros
x86, AMD: Disable wrongly set X86_FEATURE_LAHF_LM CPUID bit
x86, msr: Rewrite AMD rd/wrmsr variants
x86, msr: Add rd/wrmsr interfaces with preset registers
x86: add specific support for Intel Atom architecture
...
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Make memtype_seq_ops const
x86: uv: Clean up uv_ptc_init(), use proc_create()
x86: Use printk_once()
x86/cpu: Clean up various files a bit
x86: Remove duplicated #include
x86, ipi: Clean up safe_smp_processor_id() by using the cpu_has_apic() macro helper
x86: Clean up idt_descr and idt_tableby using NR_VECTORS instead of hardcoded number
x86: Further clean up of mtrr/generic.c
x86: Clean up mtrr/main.c
x86: Clean up mtrr/state.c
x86: Clean up mtrr/mtrr.h
x86: Clean up mtrr/if.c
x86: Clean up mtrr/generic.c
x86: Clean up mtrr/cyrix.c
x86: Clean up mtrr/cleanup.c
x86: Clean up mtrr/centaur.c
x86: Clean up mtrr/amd.c:
x86: ds.c fix invalid assignment
Merge branch 'x86-asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: remove all now-duplicate header files
x86: convert termios.h to the asm-generic version
x86: convert almost generic headers to asm-generic version
x86: convert trivial headers to asm-generic version
x86: add copies of some headers to convert to asm-generic
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
ACPI, x86: expose some IO-APIC routines when CONFIG_ACPI=n
x86, apic: Slim down stack usage in early_init_lapic_mapping()
x86, ioapic: Get rid of needless check and simplify ioapic_setup_resources()
x86, ioapic: Define IO_APIC_DEFAULT_PHYS_BASE constant
x86: Fix x86_model test in es7000_apic_is_cluster()
x86, apic: Move dmar_table_init() out of enable_IR()
x86, ioapic: Panic on irq-pin binding only if needed
x86/apic: Enable x2APIC without interrupt remapping under KVM
x86, apic: Drop redundant bit assignment
x86, ioapic: Throw BUG instead of NULL dereference
x86, ioapic: Introduce for_each_irq_pin() helper
x86: Remove superfluous NULL pointer check in destroy_irq()
x86/ioapic.c: unify ioapic_retrigger_irq()
x86/ioapic.c: convert __target_IO_APIC_irq to conventional for() loop
x86/ioapic.c: clean up replace_pin_at_irq_node logic and comments
x86/ioapic.c: convert replace_pin_at_irq_node to conventional for() loop
x86/ioapic.c: simplify add_pin_to_irq_node()
x86/ioapic.c: convert io_apic_level_ack_pending loop to normal for() loop
x86/ioapic.c: move lost comment to what seems like appropriate place
x86/ioapic.c: remove redundant declaration of irq_pin_list
...
Ryusuke Konishi [Sat, 8 Aug 2009 07:09:46 +0000 (16:09 +0900)]
fs/Kconfig: move nilfs2 outside misc filesystems
Some people asked me questions like the following:
On Wed, 15 Jul 2009 13:11:21 +0200, Leon Woestenberg wrote:
> just wondering, any reasons why NILFS2 is one of the miscellaneous
> filesystems and, for example, btrfs, is not in Kconfig?
Actually, nilfs is NOT a filesystem came from other operating systems,
but a filesystem created purely for Linux. Nor is it a flash
filesystem but that for generic block devices.
So, this moves nilfs outside the misc category as I responded in LKML
"Re: Why does NILFS2 hide under Miscellaneous filesystems?"
(Message-Id: <20090716.002526.93465395.ryusuke@osrg.net>).
Ryusuke Konishi [Sat, 15 Aug 2009 06:34:33 +0000 (15:34 +0900)]
nilfs2: allow btree code to directly call dat operations
The current btree code is written so that btree functions call dat
operations via wrapper functions in bmap.c when they allocate, free,
or modify virtual block addresses.
This abstraction requires additional function calls and causes
frequent call of nilfs_bmap_get_dat() function since it is used in the
every wrapper function.
This removes the wrapper functions and makes them available from
btree.c and direct.c, which will increase the opportunity of
compiler optimization.
Ryusuke Konishi [Sat, 15 Aug 2009 04:47:09 +0000 (13:47 +0900)]
nilfs2: remove individual gfp constants for each metadata file
This gets rid of NILFS_CPFILE_GFP, NILFS_SUFILE_GFP, NILFS_DAT_GFP,
and NILFS_IFILE_GFP. All of these constants refer to NILFS_MDT_GFP,
and can be removed.
projects / karo-tx-linux.git / log