ASoC: Samsung: Do not register samsung audio dma device as pdev
Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This change removes the platform_device completely. Each Samsung DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Wed, 5 Dec 2012 17:20:38 +0000 (18:20 +0100)]
ASoC: McASP: implement a way to force BCLK/LRCLK ratios
Depending on the Codec, the the BCLK/LRCLK ratio might not be freely
chosen by the CPU DAI.
For example, some Codec might want to be supplied with 32-bit samples
for both its channels regardless of the actual audio word size the CPU
sends. In such cases, the rest of the bits on the data lines must be
padded with zeros:
DATA ____||||||||||||||||_________________|||||||||| .....
|<-- data -->|<-- pads --> |
This patch adds a new clock divider to configure the BCLK/LRCLK ratio.
If the machine code uses that divider, the driver uses the specified
value, instead of deriving that information from the audio word size.
Otherwise, the original behaviour is retained.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Wed, 5 Dec 2012 17:20:37 +0000 (18:20 +0100)]
ASoC: McASP: calculate values for channel size
Change davinci_config_channel_size() to derive the values for XSSZ and
XROT in DAVINCI_MCASP_[RT]XFMT_REG from the configured word length
rather than hard-coding them in a switch/case block.
Also, by directly passing the word length to
davinci_config_channel_size(), we can get rid of the
DAVINCI_AUDIO_WORD_* enum.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Thu, 6 Dec 2012 14:35:25 +0000 (15:35 +0100)]
ASoC: omap-twl4030: Update the header file to support more boards
The common machine driver will be able to support new boards where the voice
port is also in use.
At the same time add possibility to fine tune the connections from twl4030
on the board: jack detection GPIO, input/output selection
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 6 Dec 2012 06:29:34 +0000 (15:29 +0900)]
ASoC: arizona: Make FLL lock timeout very high
Provide robustness against low quality FLL sync clocks by increasing the
timeout for lock to an absurdly high point; we should never get anywhere
near hitting the timeout in a real system unless it is failing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Mon, 3 Dec 2012 08:39:08 +0000 (09:39 +0100)]
ASoC: zoom2: Remove HS mux GPIO handling to avoid kernel crash due to BUG_ON()
The machine driver try to use GPIO15 of twl4030 for HS MUX which supposed to
select between TWL's HSOL/R and tlv320aic3254's HPL/R.
The TWL's GPIO allocated dynamically so the (OMAP_MAX_GPIO_LINES + 15) is no
longer valid GPIO number causing a kernel crash due to BUG_ON()
Also the current machine driver supports only TWL audio currently: there is
no need to control the GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bo Shen [Wed, 28 Nov 2012 03:46:13 +0000 (11:46 +0800)]
ASoC: atmel-pcm: dma support based on pcm dmaengine
Specify overrun bit in interrupt mask
Add dmaengine specific routines
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[voice.shen@atmel.com: adapt to soc dmaengine framework] Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bo Shen [Wed, 28 Nov 2012 03:46:12 +0000 (11:46 +0800)]
ASoC: atmel-pcm: split into two file
This patch is split original atmel-pcm.c into new atmel-pcm.c and
atmel-pcm-pdc.c two files. The new atmel-pcm.c is the share routine
while will be used for pdc or dma transfer.
Using SND_ATMEL_SOC_PDC to select using PDC for audio transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sachin Kamat [Mon, 26 Nov 2012 11:49:43 +0000 (17:19 +0530)]
ASoC: wm8960: Use devm_regmap_init_i2c()
devm_regmap_init_i2c() is device managed and makes error
handling and code cleanup simpler. There was no explicit
regmap_exit call in this function which was probably a bug.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Padmavathi Venna [Wed, 28 Nov 2012 10:47:48 +0000 (16:17 +0530)]
ASoC: Samsung: Get I2S src_clk from clock alias id.
As the I2S src clks are registered with clkdev using generic
connection id, driver can get the clk name using generic id.
So the variable representing the array of rclk src clks is
deleted.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 28 Nov 2012 17:20:32 +0000 (17:20 +0000)]
ASoC: wm_adsp: Enable DVFS for ADSP2
Some ADSP devices can make use of DVFS to optimise power consumption
depending on the operating frequency of the DSP core. Implement
support for this in the generic ADSP code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 26 Nov 2012 21:17:21 +0000 (21:17 +0000)]
Input - arizona-haptics: Add driver haptics module on Arizona CODECs
The Arizona CODECs contain a haptics module providing vibration feedback
support. Implement basic support for this, providing simple start/stop and
signal magnitude control.
Since the output path for haptics is routed through the CODEC audio routing
it is modelled as a signal generator within ASoC, the haptics driver calls
DAPM to start and stop the output drivers. An appropriate output path must
be configured via ALSA to connect the haptics source to the correct output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 26 Nov 2012 21:11:10 +0000 (21:11 +0000)]
mfd: arizona: Allow the CODEC DAPM context to be accessed elsewhere
Some other device functions need to integrate with signal sources in the
audio portion (primarily for haptics) so allow CODEC to export the DAPM
context by pointing to it from the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tony Lindgren [Wed, 21 Nov 2012 17:42:25 +0000 (09:42 -0800)]
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
We cannot include any plat or mach headers for the multiplatform
support.
Fix the issue by defining local mcbsp_omap1().
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lothar Waßmann [Mon, 26 Nov 2012 08:50:47 +0000 (09:50 +0100)]
ASoC: fsl: fix miscompilation of snd-soc-imx-pcm
Hi Mark,
thanks your insisting on a better description for the patch, I found a
more appropriate solution for the problem:
Compiling the SoC Audio driver for Freescale i.MX as a module
(CONFIG_SND_SOC_IMX_PCM=m) results in a non-functional sound driver
indicated by the error message:
| imx-sgtl5000 sound.1: platform imx-pcm-audio not registered
| imx-sgtl5000 sound.1: snd_soc_register_card failed (-517)
| platform sound.1: Driver imx-sgtl5000 requests probe deferral
instead of the message:
| imx-sgtl5000 sound.1: sgtl5000 <-> 63fcc000.ssi mapping ok
that is to be expected upon loading the snd-soc-imx-pcm.ko module.
The build log reveals, that the file imx-pcm-dma.o (or imx-pcm-fiq.o
depending on the kernel configuration), which should be linked
together with imx-pcm.o into snd-imx-pcm.ko, is not being compiled in
this case.
The make rules for these files shows that the target object imx-pcm.o
is assigned to the variable snd-soc-imx-pcm-y while
imx-pcm-{dma,fiq}.o are added to to
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_DMA) and
snd-soc-imx-pcm-$(CONFIG_SND_SOC_IMX_PCM_FIQ) which resolve to
snd-soc-imx-pcm-m in this case.
According to Documentation/kbuild/modules.txt:
|When the module is built from multiple sources, an additional line is
|needed listing the files:
|
| <module_name>-y := <src1>.o <src2>.o ...
Thus the type of the config variables CONFIG_SND_SOC_IMX_PCM_DMA and
CONFIG_SND_SOC_IMX_PCM_FIQ should be 'bool' instead of 'tristate' to
resolve to 'y' when selected.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lothar Waßmann [Fri, 23 Nov 2012 09:12:13 +0000 (10:12 +0100)]
ASoC: fsl: fix miscompilation of snd-soc-imx-pcm
Due to a broken make rule, sound/soc/fsl/imx-pcm-dma.c or
sound/soc/fsl/imx-pcm-fiq.c (whatever is selected via Kconfig) will
not be compiled into imx-pcm.o when building as module, i.e.:
CONFIG_SND_SOC_IMX_PCM=m
CONFIG_SND_SOC_IMX_PCM_DMA=m
resulting in a non-functional sound driver.
This gives the error messages:
| imx-sgtl5000 sound.1: platform imx-pcm-audio not registered
| imx-sgtl5000 sound.1: snd_soc_register_card failed (-517)
| platform sound.1: Driver imx-sgtl5000 requests probe deferral
when loading the driver instead of what's to be expected:
| imx-sgtl5000 sound.1: sgtl5000 <-> 63fcc000.ssi mapping ok
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
projects / linux-beck.git / log