On the second open() on /mnt/one, FUSE would have used the old
nodeid (file handle) trying to re-open it. Gluster is returning
-ESTALE. The ESTALE propagates back to namei.c:filename_lookup()
where lookup is re-attempted with LOOKUP_REVAL. The right
behavior now, would be for FUSE to ignore the entry-timeout and
and do the up-call revalidation. Instead FUSE is ignoring
LOOKUP_REVAL, succeeding the revalidation (because entry-timeout
has not passed), and open() is again retried on the old file
handle and finally the ESTALE is going back to the application.
Fix: if revalidation is happening with LOOKUP_REVAL, then ignore
entry-timeout and always do the up-call.
Signed-off-by: Anand Avati <avati@redhat.com> Reviewed-by: Niels de Vos <ndevos@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the initialization of Intel HDMI controller fails due to missing
i915 kernel symbols (e.g. HD-audio is built in while i915 is module),
the driver discontinues the probe. However, since the probe was done
asynchronously, the driver object still remains, thus the relevant PM
ops are still called at suspend/resume. This results in the bad access
to the incomplete audio card object, eventually leads to Oops or stall
at PM.
This patch adds the missing checks of chip->init_failed flag at each
PM callback in order to fix the problem above.
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cdc662f704fa9262e5c6e213b4ab45dd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cdc6 (USB: Allow USB 3.0 ports to be disabled.) Signed-off-by: Gavin Guo <gavin.guo@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some machines (eg. Lenovo Z480) ECs are not stable during boot up
and causes battery driver fails to be loaded due to failure of getting
battery information from EC sometimes. After several retries, the
operation will work. This patch is to retry to get battery information 5
times if the first try fails.
[ backport to 3.14.5: removed second parameter in acpi_battery_update(),
introduced by the commit 9e50bc14a7f58b5d8a55973b2d69355852ae2dae (ACPI /
battery: Accelerate battery resume callback)]
[naszar <naszar@ya.ru>: backport to 3.14.5] Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581 Reported-and-tested-by: naszar <naszar@ya.ru> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __ioremap_caller() (the guts of ioremap), we loop over the range of
pfns being remapped and checks each one individually with page_is_ram().
For large ioremaps, this can be very slow. For example, we have a
device with a 256 GiB PCI BAR, and ioremapping this BAR can take 20+
seconds -- sometimes long enough to trigger the soft lockup detector!
Internally, page_is_ram() calls walk_system_ram_range() on a single
page. Instead, we can make a single call to walk_system_ram_range()
from __ioremap_caller(), and do our further checks only for any RAM
pages that we find. For the common case of MMIO, this saves an enormous
amount of work, since the range being ioremapped doesn't intersect
system RAM at all.
With this change, ioremap on our 256 GiB BAR takes less than 1 second.
A number of attempts to fix the problem by moving around code have been
unsuccessful and resulted in failed builds for some configurations and
the discovery of toolchain bugs.
Fix the problem by disabling RELOCATABLE for COMPILE_TEST builds instead.
While this is less than perfect, it avoids substantial code changes
which would otherwise be necessary just to make COMPILE_TEST builds
happy and might have undesired side effects.
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setpie':
drivers/rtc/rtc-puv3.c:74: error: implicit declaration of function 'dev_debug'
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (for unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setalarm':
drivers/rtc/rtc-puv3.c:143: error: 'struct device' has no member named 'dev'
The per_cpu buffers are created one per possible CPU. But these do
not mean that those CPUs are online, nor do they even exist.
With the addition of the ring buffer polling, it assumes that the
caller polls on an existing buffer. But this is not the case if
the user reads trace_pipe from a CPU that does not exist, and this
causes the kernel to crash.
Simple fix is to check the cpu against buffer bitmask against to see
if the buffer was allocated or not and return -ENODEV if it is
not.
More updates were done to pass the -ENODEV back up to userspace.
On most gen2-4 platforms the GTT can be (or maybe always is?)
inside the stolen memory region. If that's the case, reduce the
size of the stolen memory appropriately to make make sure we
don't clobber the GTT.
v2: Deal with gen4 36 bit physical address
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151 Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we set the valid bit on invalid GART entries they are
loaded into the TLB when an adjacent entry is loaded. This
poisons the TLB with invalid entries which are sometimes
not correctly removed on TLB flush.
For stable inclusion the patch probably needs to be modified a bit.
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ INFO: possible circular locking dependency detected ]
3.16.0-rc2-mm1+ #7 Tainted: G O
-------------------------------------------------------
kworker/u24:0/4356 is trying to acquire lock:
(&(&sbi->s_es_lru_lock)->rlock){+.+.-.}, at: [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0
but task is already holding lock:
(&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180
The first time that we allocate from an uninitialized inode allocation
bitmap, if the block allocation bitmap is also uninitalized, we need
to get write access to the block group descriptor before we start
modifying the block group descriptor flags and updating the free block
count, etc. Otherwise, there is the potential of a bad journal
checksum (if journal checksums are enabled), and of the file system
becoming inconsistent if we crash at exactly the wrong time.
pci_wait_for_pending() uses word access, so we shouldn't be passing
an offset that is only byte aligned. Use the control register offset
instead, shifting the mask to match.
Fixes: d0b4cc4e3270 ("PCI: Wrong register used to check pending traffic") Fixes: 157e876ffe0b ("PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction()) Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that cpu->cpu is set before writing MSR_IA32_PERF_CTL during CPU
initialization. Otherwise only cpu0 has its P-state set and all other
cores are left with their values unchanged.
In most cases, this is not too serious because the P-states will be set
correctly when the timer function is run. But when the default governor
is set to performance, the per-CPU current_pstate stays the same forever
and no attempts are made to write the MSRs again.
Signed-off-by: Vincent Minet <vincent@vincent-minet.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If turbo is disabled in the BIOS bit 38 should be set in
MSR_IA32_MISC_ENABLE register per section 14.3.2.1 of the SDM Vol 3
document 325384-050US Feb 2014. If this bit is set do *not* attempt
to disable trubo via the MSR_IA32_PERF_CTL register. On some systems
trying to disable turbo via MSR_IA32_PERF_CTL will cause subsequent
writes to MSR_IA32_PERF_CTL not take affect, in fact reading
MSR_IA32_PERF_CTL will not show the IDA/Turbo DISENGAGE bit(32) as
set. A write of bit 32 to zero returns to normal operation.
Also deal with the case where the processor does not support
turbo and the BIOS does not report the fact in MSR_IA32_MISC_ENABLE
but does report the max and turbo P states as the same value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=64251 Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 21855ff5 (intel_pstate: Set turbo VID for BayTrail) introduced
setting the turbo VID which is required to prevent a machine check on
some Baytrail SKUs under heavy graphics based workloads. The
docmumentation update that brought the requirement to light also
changed the bit mask used for enumerating P state and VID values from
0x7f to 0x3f.
This change returns the mask value to 0x7f.
Tested with the Intel NUC DN2820FYK,
BIOS version FYBYT10H.86A.0034.2014.0513.1413 with v3.16-rc1 and
v3.14.8 kernel versions.
Fixes: 21855ff5 (intel_pstate: Set turbo VID for BayTrail) Link: https://bugzilla.kernel.org/show_bug.cgi?id=77951 Reported-and-tested-by: Rune Reterson <rune@megahurts.dk> Reported-and-tested-by: Eric Eickmeyer <erich@ericheickmeyer.com> Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2c140a246dc ("dm: allow remove to be deferred") introduced a
deferred removal feature for the device mapper. When this feature is
used (by passing a flag DM_DEFERRED_REMOVE to DM_DEV_REMOVE_CMD ioctl)
and the user tries to remove a device that is currently in use, the
device will be removed automatically in the future when the last user
closes it.
Device mapper used the system workqueue to perform deferred removals.
However, some targets (dm-raid1, dm-mpath, dm-stripe) flush work items
scheduled for the system workqueue from their destructor. If the
destructor itself is called from the system workqueue during deferred
removal, it introduces a possible deadlock - the workqueue tries to flush
itself.
Fix this possible deadlock by introducing a new workqueue for deferred
removals. We allocate just one workqueue for all dm targets. The
ability of dm targets to process IOs isn't dependent on deferred removal
of unused targets, so a deadlock due to shared workqueue isn't possible.
Also, cleanup local_init() to eliminate potential for returning success
on failure.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread. If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.
Fix this race by using a completion in sync_io() and dec_count().
Reported-by: Minfei Huang <huangminfei@ucloud.cn> Signed-off-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Win8, we have implemented several optimizations to improve the
scalability and performance of the VMBUS transport between the Host and the
Guest. Some of the non-performance critical services cannot leverage these
optimization since they only read and process one message at a time.
Make adjustments to the callback dispatch code to account for the way
non-performance critical drivers handle reading of the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HDMI PLL input to the tv mux is supposed to be 3, not 2. Fix
the code so that we can properly select the HDMI PLL.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)" Reported-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After unbinding the driver memory was corrupted by double free of
clk_lookup structure. This lead to OOPS when re-binding the driver
again.
The driver allocated memory for 'clk_lookup' with devm_kzalloc. During
driver removal this memory was freed twice: once by clkdev_drop() and
second by devm code.
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/sched.h implements TASK_SIZE_OF as TASK_SIZE if it
is not set by the architecture headers. TASK_SIZE uses the
current task to determine the size of the virtual address space.
On a 64-bit kernel this will cause reading /proc/pid/pagemap of a
64-bit process from a 32-bit process to return EOF when it reads
past 0xffffffff.
Implement TASK_SIZE_OF exactly the same as TASK_SIZE with
test_tsk_thread_flag instead of test_thread_flag.
Signed-off-by: Colin Cross <ccross@android.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Byte-to-bit-count computation is only partly converted to big-endian and is
mixing in CPU-endian values. Problem was noticed by sparce with warning:
CHECK arch/x86/crypto/sha512_ssse3_glue.c
arch/x86/crypto/sha512_ssse3_glue.c:144:19: warning: restricted __be64 degrades to integer
arch/x86/crypto/sha512_ssse3_glue.c:144:17: warning: incorrect type in assignment (different base types)
arch/x86/crypto/sha512_ssse3_glue.c:144:17: expected restricted __be64 <noident>
arch/x86/crypto/sha512_ssse3_glue.c:144:17: got unsigned long long
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commtit 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to
drivers/cpufreq) this added dependancy only for CONFIG_ARCH_DAVINCI_DA850
where as davinci_cpufreq_init() call is used by all davinci platform.
This patch fixes following build error:
arch/arm/mach-davinci/built-in.o: In function `davinci_init_late':
:(.init.text+0x928): undefined reference to `davinci_cpufreq_init'
make: *** [vmlinux] Error 1
Fixes: 8a7b1227e303 (cpufreq: davinci: move cpufreq driver to drivers/cpufreq) Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.
We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.
This was manifesting as a bug with ppc64_cpu --frequency:
$ sudo ppc64_cpu --frequency
WARNING: couldn't run on cpu 0
WARNING: couldn't run on cpu 8
...
WARNING: couldn't run on cpu 144
WARNING: couldn't run on cpu 152
min: 18446744073.710 GHz (cpu -1)
max: 0.000 GHz (cpu -1)
avg: 0.000 GHz
The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.
By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:
This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.
Fixes: e05b9b9e5c10 ("powerpc/perf: Power8 PMU support") Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.
This saves us adding a MMCR2 define for a future patch.
Signed-off-by: Joel Stanley <joel@jms.id.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.
A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.
This patch takes the second option.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition in ec_transaction_completed().
When ec_transaction_completed() is called in the GPE handler, it could
return true because of (ec->curr == NULL). Then the wake_up() invocation
could complete the next command unexpectedly since there is no lock between
the 2 invocations. With the previous cleanup, the IBF=0 waiter race need
not be handled any more. It's now safe to return a flag from
advance_condition() to indicate the requirement of wakeup, the flag is
returned from a locked context.
The ec_transaction_completed() is now only invoked by the ec_poll() where
the ec->curr is ensured to be different from NULL.
After cleaning up, the EVT_SCI=1 check should be moved out of the wakeup
condition so that an EVT_SCI raised with (ec->curr == NULL) can trigger a
QR_SC command.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911 Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk> Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org> Reported-by: Barton Xu <tank.xuhan@gmail.com> Tested-by: Steffen Weber <steffen.weber@gmail.com> Tested-by: Arthur Chen <axchen@nvidia.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we've added the first command byte write into advance_transaction(),
the IBF=0 waiter is duplicated with the command completion waiter
implemented in the ec_poll() because:
If IBF=1 blocked the first command byte write invoked in the task
context ec_poll(), it would be kicked off upon IBF=0 interrupt or timed
out and retried again in the task context.
Remove this seperate and duplicate IBF=0 waiter. By doing so we can
reduce the overall number of times to access the EC_SC(R) status
register.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911 Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk> Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org> Reported-by: Barton Xu <tank.xuhan@gmail.com> Tested-by: Steffen Weber <steffen.weber@gmail.com> Tested-by: Arthur Chen <axchen@nvidia.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the first command byte write into advance_transaction() so that all
EC register accesses that can affect the command processing state machine
can happen in this asynchronous state machine advancement function.
The advance_transaction() function then can be a complete implementation
of an asyncrhonous transaction for a single command so that:
1. The first command byte can be written in the interrupt context;
2. The command completion waiter can also be used to wait the first command
byte's timeout;
3. In BURST mode, the follow-up command bytes can be written in the
interrupt context directly, so that it doesn't need to return to the
task context. Returning to the task context reduces the throughput of
the BURST mode and in the worst cases where the system workload is very
high, this leads to the hardware driven automatic BURST mode exit.
In order not to increase memory consumption, convert 'done' into 'flags'
to contain multiple indications:
1. ACPI_EC_COMMAND_COMPLETE: converting from original 'done' condition,
indicating the completion of the command transaction.
2. ACPI_EC_COMMAND_POLL: indicating the availability of writing the first
command byte. A new command can utilize this flag to compete for the
right of accessing the underlying hardware. There is a follow-up bug
fix that has utilized this new flag.
The 2 flags are important because it also reflects a key concept of IO
programs' design used in the system softwares. Normally an IO program
running in the kernel should first be implemented in the asynchronous way.
And the 2 flags are the most common way to implement its synchronous
operations on top of the asynchronous operations:
1. POLL: This flag can be used to block until the asynchronous operations
can happen.
2. COMPLETE: This flag can be used to block until the asynchronous
operations have completed.
By constructing code cleanly in this way, many difficult problems can be
solved smoothly.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911 Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk> Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org> Reported-by: Barton Xu <tank.xuhan@gmail.com> Tested-by: Steffen Weber <steffen.weber@gmail.com> Tested-by: Arthur Chen <axchen@nvidia.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advance_transaction() will be invoked from the IRQ context GPE handler
and the task context ec_poll(). The handling of this function is locked so
that the EC state machine are ensured to be advanced sequentially.
But there is a problem. Before invoking advance_transaction(), EC_SC(R) is
read. Then for advance_transaction(), there could be race condition around
the lock from both contexts. The first one reading the register could fail
this race and when it passes the stale register value to the state machine
advancement code, the hardware condition is totally different from when
the register is read. And the hardware accesses determined from the wrong
hardware status can break the EC state machine. And there could be cases
that the functionalities of the platform firmware are seriously affected.
For example:
1. When 2 EC_DATA(W) writes compete the IBF=0, the 2nd EC_DATA(W) write may
be invalid due to IBF=1 after the 1st EC_DATA(W) write. Then the
hardware will either refuse to respond a next EC_SC(W) write of the next
command or discard the current WR_EC command when it receives a EC_SC(W)
write of the next command.
2. When 1 EC_SC(W) write and 1 EC_DATA(W) write compete the IBF=0, the
EC_DATA(W) write may be invalid due to IBF=1 after the EC_SC(W) write.
The next EC_DATA(R) could never be responded by the hardware. This is
the root cause of the reported issue.
Fix this issue by moving the EC_SC(R) access into the lock so that we can
ensure that the state machine is advanced consistently.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911 Reported-and-tested-by: Gareth Williams <gareth@garethwilliams.me.uk> Reported-and-tested-by: Hans de Goede <jwrdegoede@fedoraproject.org> Reported-by: Barton Xu <tank.xuhan@gmail.com> Tested-by: Steffen Weber <steffen.weber@gmail.com> Tested-by: Arthur Chen <axchen@nvidia.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change has caused a regression in (at least) serial port detection
for a number of machines (see LP#1313981 [1]). These seem to represent
their IO regions (presumably incorrectly) as a zero length region.
Reverting the above commit restores these serial devices.
Only elide zero length resources which lie at address 0.
Fixes: b355cee88e3b (ACPI / resources: ignore invalid ACPI device resources) Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit ab0fd674d6ce (ACPI / AC: Remove AC's proc directory.),
because some old tools (e.g. kpowersave from kde 3.5.10) are still
using /proc/acpi/ac_adapter.
Fixes: ab0fd674d6ce (ACPI / AC: Remove AC's proc directory.) Reported-and-tested-by: Sorin Manolache <sorinm@gmail.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module test script for the adm1021 driver exposes a cache problem
when writing temperature limits. temp_min and temp_max are expected
to be stored in milli-degrees C but are stored in degrees C.
Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.
This patch ensures the fan_div cache is updated in set_fan_div().
Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upper limit for write operations to temperature limit registers
was clamped to a fractional value. However, limit registers do
not support fractional values. As a result, upper limits of 127.5
degrees C or higher resulted in a rounded limit of 128 degrees C.
Since limit registers are signed, this was stored as -128 degrees C.
Clamp limits to (-55, +127) degrees C to solve the problem.
Value on writes to auto_temp[12]_min and auto_temp[12]_max were not
clamped at all, but masked. As a result, out-of-range writes resulted
in a more or less arbitrary limit. Clamp those attributes to (0, 127)
degrees C for more predictable results.
Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is customary to clamp limits instead of bailing out with an error
if a configured limit is out of the range supported by the driver.
This simplifies limit configuration, since the user will not typically
know chip and/or driver specific limits.
On 05/21/2014 04:22 PM, Aaron Lu wrote:
> On 05/21/2014 01:57 PM, Kui Zhang wrote:
>> Hello,
>>
>> I get following error when rmmod thermal.
>>
>> rmmod thermal
>> Killed
While dealing with this problem, I found another problem that also
results in a kernel crash on thermal module removal:
From: Aaron Lu <aaron.lu@intel.com>
Date: Wed, 21 May 2014 16:05:38 +0800
Subject: thermal: hwmon: Make the check for critical temp valid consistent
We used the tz->ops->get_crit_temp && !tz->ops->get_crit_temp(tz, temp)
to decide if we need to create the temp_crit attribute file but we just
check if tz->ops->get_crit_temp exists to decide if we need to remove
that attribute file. Some ACPI thermal zone doesn't have a valid critical
trip point and that would result in removing a non-existent device file
on thermal module unload.
Commit f36fdb9f0266 (i8k: Force SMM to run on CPU 0) adds support
for multi-core CPUs to the driver. Unfortunately, that causes it
to fail loading if compiled without SMP support, at least on
32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell
signature", and function i8k_smm is found to return -EINVAL.
Testing revealed that the culprit is the missing return value check
of set_cpus_allowed_ptr.
Fixes: f36fdb9f0266 (i8k: Force SMM to run on CPU 0) Reported-by: Jim Bos <jim876@xs4all.nl> Tested-by: Jim Bos <jim876@xs4all.nl> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Andreas Mohr <andi@lisas.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my investigation, I found the root cause is wq_numa_possible_cpumask.
All entries of wq_numa_possible_cpumask is allocated by
alloc_cpumask_var_node(). And these entries are used without initializing.
So these entries have wrong value.
When hot-adding and onlining CPU, wq_update_unbound_numa() is called.
wq_update_unbound_numa() calls alloc_unbound_pwq(). And alloc_unbound_pwq()
calls get_unbound_pool(). In get_unbound_pool(), worker_pool->node is set
as follow:
3592 /* if cpumask is contained inside a NUMA node, we belong to that node */
3593 if (wq_numa_enabled) {
3594 for_each_node(node) {
3595 if (cpumask_subset(pool->attrs->cpumask,
3596 wq_numa_possible_cpumask[node])) {
3597 pool->node = node;
3598 break;
3599 }
3600 }
3601 }
But wq_numa_possible_cpumask[node] does not have correct cpumask. So, wrong
node is selected. As a result, kernel panic occurs.
By this patch, all entries of wq_numa_possible_cpumask are allocated by
zalloc_cpumask_var_node to initialize them. And the panic disappeared.
The cause is that cpuset_mems_allowed() try to take
mutex_lock(&callback_mutex) under the rcu_read_lock(which was hold in
__mpol_dup()). And in cpuset_mems_allowed(), the access to cpuset is
under rcu_read_lock, so in __mpol_dup, we can reduce the rcu_read_lock
protection region to protect the access to cpuset only in
current_cpuset_is_being_rebound(). So that we can avoid this bug.
This patch is a temporary solution that just addresses the bug
mentioned above, can not fix the long-standing issue about cpuset.mems
rebinding on fork():
"When the forker's task_struct is duplicated (which includes
->mems_allowed) and it races with an update to cpuset_being_rebound
in update_tasks_nodemask() then the task's mems_allowed doesn't get
updated. And the child task's mems_allowed can be wrong if the
cpuset's nodemask changes before the child has been added to the
cgroup's tasklist."
This patch affects only architectures where the stack grows upwards
(currently parisc and metag only). On those do not hardcode the maximum
initial stack size to 1GB for 32-bit processes, but make it configurable
via a config option.
The main problem with the hardcoded stack size is, that we have two
memory regions which grow upwards: stack and heap. To keep most of the
memory available for heap in a flexmap memory layout, it makes no sense
to hard allocate up to 1GB of the memory for stack which can't be used
as heap then.
This patch makes the stack size for 32-bit processes configurable and
uses 80MB as default value which has been in use during the last few
years on parisc and which hasn't showed any problems yet.
Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: linux-parisc@vger.kernel.org Cc: linux-metag@vger.kernel.org Cc: John David Anglin <dave.anglin@bell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On parisc we can not use the existing compat implementation for fanotify_mark()
because for the 64bit mask parameter the higher and lower 32bits are ordered
differently than what the compat function expects from big endian
architectures.
Specifically:
It finally turned out, that on hppa we end up with different assignments
of parameters to kernel arguments depending on if we call the glibc
wrapper function
int fanotify_mark (int __fanotify_fd, unsigned int __flags,
uint64_t __mask, int __dfd, const char *__pathname);
or directly calling the syscall manually
syscall(__NR_fanotify_mark, ...)
Reason is, that the syscall() function is implemented as C-function and
because we now have the sysno as first parameter in front of the other
parameters the compiler will unexpectedly add an empty paramenter in
front of the u64 value to ensure the correct calling alignment for 64bit
values.
This means, on hppa you can't simply use syscall() to call the kernel
fanotify_mark() function directly, but you have to use the glibc
function instead.
This patch fixes the kernel in the hppa-arch specifc coding to adjust
the parameters in a way as if userspace calls the glibc wrapper function
fanotify_mark().
Since AI lines could be selected at will (linux-3.11) the sending
and receiving ends of the FIFO does not agree about what step is used
for a line. It only works if the last lines are used, like 5,6,7,
and fails if ie 2,4,6 is selected in DT.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com> Tested-by: Zubair Lutfullah <zubair.lutfullah@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair USB Dongles are shipped with Corsair AXi series PSUs.
These are cp210x serial usb devices, so make driver detect these.
I have a program, that can get information from these PSUs.
Tested with 2 different dongles shipped with Corsair AX860i and
AX1200i units.
In v2.6.34 commit 9d8cebd4bcd7 ("mm: fix mbind vma merge problem")
introduced vma merging to mbind(), but it should have also changed the
convention of passing start vma from queue_pages_range() (formerly
check_range()) to new_vma_page(): vma merging may have already freed
that structure, resulting in BUG at mm/mempolicy.c:1738 and probably
worse crashes.
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b1cb0982bdd6 ("change the management method of free objects of
the slab") introduced a bug on slab leak detector
('/proc/slab_allocators'). This detector works like as following
decription.
1. traverse all objects on all the slabs.
2. determine whether it is active or not.
3. if active, print who allocate this object.
but that commit changed the way how to manage free objects, so the logic
determining whether it is active or not is also changed. In before, we
regard object in cpu caches as inactive one, but, with this commit, we
mistakenly regard object in cpu caches as active one.
This intoduces kernel oops if DEBUG_PAGEALLOC is enabled. If
DEBUG_PAGEALLOC is enabled, kernel_map_pages() is used to detect who
corrupt free memory in the slab. It unmaps page table mapping if object
is free and map it if object is active. When slab leak detector check
object in cpu caches, it mistakenly think this object active so try to
access object memory to retrieve caller of allocation. At this point,
page table mapping to this object doesn't exist, so oops occurs.
Following is oops message reported from Dave.
It blew up when something tried to read /proc/slab_allocators
(Just cat it, and you should see the oops below)
To fix the problem, I introduce an object status buffer on each slab.
With this, we can track object status precisely, so slab leak detector
would not access active object and no kernel oops would occur. Memory
overhead caused by this fix is only imposed to CONFIG_DEBUG_SLAB_LEAK
which is mainly used for debugging, so memory overhead isn't big
problem.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by: Dave Jones <davej@redhat.com> Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Vladimir Davydov <vdavydov@parallels.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changing PTEs and PMDs to pte_numa & pmd_numa is done with the
mmap_sem held for reading, which means a pmd can be instantiated
and turned into a numa one while __handle_mm_fault() is examining
the value of old_pmd.
If that happens, __handle_mm_fault() should just return and let
the page fault retry, instead of throwing an oops. This is
handled by the test for pmd_trans_huge(*pmd) below.
Signed-off-by: Rik van Riel <riel@redhat.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reported-by: Sunil Pandey <sunil.k.pandey@intel.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: linux-mm@kvack.org Cc: lwoodman@redhat.com Cc: dave.hansen@intel.com Link: http://lkml.kernel.org/r/20140429153615.2d72098e@annuminas.surriel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Patrick McLean <chutzpah@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function unifb_mmap calls functions which are defined in linux/mm.h
and asm/pgtable.h
The related error (for unicore32 with unicore32_defconfig):
CC drivers/video/fbdev/fb-puv3.o
drivers/video/fbdev/fb-puv3.c: In function 'unifb_mmap':
drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of
function 'vm_iomap_memory'
drivers/video/fbdev/fb-puv3.c:646: error: implicit declaration of
function 'pgprot_noncached'
Signed-off-by: Zhichuang Sun <sunzc522@gmail.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Joe Perches <joe@perches.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: linux-fbdev@vger.kernel.org Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need include "asm/pgtable.h" to include "asm-generic/pgtable-nopmd.h",
so can let 'pmd_t' defined. The related error with allmodconfig:
CC arch/unicore32/mm/alignment.o
In file included from arch/unicore32/mm/alignment.c:24:
arch/unicore32/include/asm/tlbflush.h:135: error: expected .). before .*. token
arch/unicore32/include/asm/tlbflush.h:154: error: expected .). before .*. token
In file included from arch/unicore32/mm/alignment.c:27:
arch/unicore32/mm/mm.h:15: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:20: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
arch/unicore32/mm/mm.h:25: error: expected .=., .,., .;., .sm. or ._attribute__. before .*. token
make[1]: *** [arch/unicore32/mm/alignment.o] Error 1
make: *** [arch/unicore32/mm] Error 2
Causes the ratelimiting to spam the kernel log with the "callbacks suppressed"
message below, even while the dev_dbg it is supposed to rate limit wouldn't
print anything because DEBUG is not defined for this device.
The new- prefix on ses and auid are un-necessary and break ausearch.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Reported-by: Steve Grubb <sgrubb@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
deletes aio context and all resources related to. It makes sense that
no IO operations connected to the context should be running after the context
is destroyed. As we removed io_context we have no chance to
get requests status or call io_getevents().
man page for io_destroy says that this function may block until
all context's requests are completed. Before kernel 3.11 io_destroy()
blocked indeed, but since aio refactoring in 3.11 it is not true anymore.
Here is a pseudo-code that shows a testcase for a race condition discovered
in 3.11:
initialize io_context
io_submit(read to buffer)
io_destroy()
// context is destroyed so we can free the resources
free(buffers);
// if the buffer is allocated by some other user he'll be surprised
// to learn that the buffer still filled by an outstanding operation
// from the destroyed io_context
The fix is straight-forward - add a completion struct and wait on it
in io_destroy, complete() should be called when number of in-fligh requests
reaches zero.
If two or more io_destroy() called for the same context simultaneously then
only the first one waits for IO completion, other calls behaviour is undefined.
Tested: ran http://pastebin.com/LrPsQ4RL testcase for several hours and
do not see the race condition anymore.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atm, we refcount both power domains and power wells and
intel_display_power_enabled_sw() returns the power domain refcount. What
the callers are really interested in though is the sw state of the
underlying power wells. Due to this we will report incorrectly that a
given power domain is off if its power wells were enabled via another
power domain, for example POWER_DOMAIN_INIT which enables all power
wells.
As a fix return instead the state based on the refcount of all power
wells included in the passed in power domain.
References: https://bugs.freedesktop.org/show_bug.cgi?id=79505
References: https://bugs.freedesktop.org/show_bug.cgi?id=79038 Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a27fbf2f067b0cd ("mmc: add ignorance case for CMD13 CRC error") produced
a cmd.flags unhandled in realtek pci host driver. This will make MMC
card fail to initialize, this patch is used to handle the new cmd.flags
condition and MMC card can be used.
brcmfmac has been broken on my cubietruck with a BCM43362:
brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0:
Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
since commit 53036261033: "brcmfmac: update core reset and disable routines".
The problem is that since this commit brcmf_chip_ai_resetcore no longer sets
BCMA_IOCTL itself before bringing the core out of reset, instead relying on
brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop
of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable
to always set BCMA_IOCTL even if the core is already in reset.
This fixes brcmfmac hanging in firmware loading on my board.
Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[arend@broadcom.com: rebase patch on linux-3.14.y branch] Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically what's happening is, during netns cleanup,
nf_nat_net_exit gets called before ipv4_net_exit. As I understand
it, nf_nat_net_exit is supposed to kill any conntrack entries which
have NAT context (through nf_ct_iterate_cleanup), but for some
reason this doesn't happen (perhaps something else is still holding
refs to those entries?).
When ipv4_net_exit is called, conntrack entries (including those
with NAT context) are cleaned up, but the
nat_bysource hashtable is long gone - freed in nf_nat_net_exit. The
bug happens when attempting to free a conntrack entry whose NAT hash
'prev' field points to a slot in the freed hash table (head for that
bin).
We ignore conntracks with null nat bindings. But this is wrong,
as these are in bysource hash table as well.
Restore nat-cleaning for the netns-is-being-removed case.
If INPCK is not set, input parity detection should be disabled. This means
parity errors should not be received from the tty driver, and the data
received should be treated normally.
SUS v3, 11.2.2, General Terminal Interface - Input Modes, states:
"If INPCK is set, input parity checking shall be enabled. If INPCK is
not set, input parity checking shall be disabled, allowing output parity
generation without input parity errors. Note that whether input parity
checking is enabled or disabled is independent of whether parity detection
is enabled or disabled (see Control Modes). If parity detection is enabled
but input parity checking is disabled, the hardware to which the terminal
is connected shall recognize the parity bit, but the terminal special file
shall not check whether or not this bit is correctly set."
Ignore parity errors reported by the tty driver when INPCK is not set, and
handle the received data normally.
Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
We forgot to add the status bit for the PLLs and we were using
the wrong register and masks for configuration, leading to
unexpected PLL configurations. Fix this.
Fixes: d8b212014e69 (clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in
QUERY_FUNC_CAP") did:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_OFFSET) {
which should be:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_FORCE_VLAN) {
Fix that.
Fixes: eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = fffffe0000050000
[00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407
Internal error: Oops: 96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
â\80\9cpageblock_order > MAX_ORDERâ\80\9d condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.
Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT') Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabling reading and writing to the trace file should not be able to
disable all function tracing callbacks. There's other users today
(like kprobes and perf). Reading a trace file should not stop those
from happening.
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An NFS operation that creates a new symlink includes the symlink data,
which is xdr-encoded as a length followed by the data plus 0 to 3 bytes
of zero-padding as required to reach a 4-byte boundary.
The vfs, on the other hand, wants null-terminated data.
The simple way to handle this would be by copying the data into a newly
allocated buffer with space for the final null.
The current nfsd_symlink code tries to be more clever by skipping that
step in the (likely) case where the byte following the string is already
0.
But that assumes that the byte following the string is ours to look at.
In fact, it might be the first byte of a page that we can't read, or of
some object that another task might modify.
Worse, the NFSv4 code tries to fix the problem by actually writing to
that byte.
In the NFSv2/v3 cases this actually appears to be safe:
- nfs3svc_decode_symlinkargs explicitly null-terminates the data
(after first checking its length and copying it to a new
page).
- NFSv2 limits symlinks to 1k. The buffer holding the rpc
request is always at least a page, and the link data (and
previous fields) have maximum lengths that prevent the request
from reaching the end of a page.
In the NFSv4 case the CREATE op is potentially just one part of a long
compound so can end up on the end of a page if you're unlucky.
The minimal fix here is to copy and null-terminate in the NFSv4 case.
The nfsd_symlink() interface here seems too fragile, though. It should
really either do the copy itself every time or just require a
null-terminated string.
Reported-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be returning a negative error code instead of success here.
This would have been detected by GCC, except that the "ret" variable was
initialized with a bogus value to disable GCC's uninitialized variable
warnings. I've cleaned that up, as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>