Stefan Roese [Sat, 8 Dec 2007 13:47:34 +0000 (14:47 +0100)]
ppc4xx: 405EX: Correctly enable USB pins
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.
Stefan Roese [Thu, 6 Dec 2007 04:58:43 +0000 (05:58 +0100)]
ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 30 Nov 2007 06:15:41 +0000 (07:15 +0100)]
ppc4xx: Kilauea: Add PCIe reset assertion upon power-up
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.
Kumar Gala [Wed, 21 Nov 2007 20:07:46 +0000 (14:07 -0600)]
Fix warnings from import of libfdt
cmd_fdt.c: In function fdt_print:
cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Wed, 21 Nov 2007 16:19:37 +0000 (09:19 -0700)]
[BUILD] Remove libraries when updating autoconf.mk
Fix library problems caused by conditional compilation. Using
autoconf.mk to decide which files to compile has caused a problem when
changing configuration from one board to another without clearing out
the library (*.a) files.
It used to be that the linker was always passed the same list of .o
files when building the .a files. However, that is not longer true
with conditional compilation. Now, a different board config will have
a different file list passed to the linker. The problem occurs when
a library has already been built and the board config is changed.
Since the linker will update instead of replace a preexisting library,
then if the file list changes to remove some object files the old
objects will still exist in the library.
The solution is to remove all old library files when autoconf.mk is
made.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Mon, 24 Sep 2007 15:05:31 +0000 (09:05 -0600)]
[BUILD] Generate include/autoconf.mk from board config files
Use cpp and sed to postprocess config.h and import the defined values
into include/autoconf.mk. autoconf.mk is then included by config.mk to
give 'make' access to the board configuration.
Doing this enables conditional compilation at the Makefile level instead
of by wrapping every .c file with #ifdef/#endif wrappers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[MIPS] board/gth2/lowlevel_init.S: Fix a build warning
lowlevel_init.S: Assembler messages:
lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local.
Looking at codes, the `memtest' and `clearmem' are intentional mixed
use of `global symbols' and `label' for debugging purpose. To make it
build, just disable global-symbols-use for now. As a result `memtest'
still remains as unused, but leave it be...
[MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker
Current trick to pick up GNU assembler minor version does not work with the
latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to
"(GNU Binutils) ".
au1x00_eth.c: In function 'au1x00_enet_initialize':
au1x00_eth.c:246: error: 'au1x00_miiphy_read' undeclared (first use in this function)
au1x00_eth.c:246: error: (Each undeclared identifier is reported only once
au1x00_eth.c:246: error: for each function it appears in.)
au1x00_eth.c:246: error: 'au1x00_miiphy_write' undeclared (first use in this function)
au1x00_eth.c: In function 'au1x00_miiphy_write':
au1x00_eth.c:298: warning: 'return' with no value, in function returning non-void
make[1]: *** [au1x00_eth.o] Error 1
Grant Likely [Wed, 14 Nov 2007 05:18:33 +0000 (22:18 -0700)]
powerpc: Backout relocation changes.
Ugh. I *hate* to back this change out, but these compiler flags don't
work for relocation on all versions of GCC. I've not been able to
reproduce the environment in my setup (and hence, not been able to
find a combination that *does* work), so I've got no choice but to go
back to the old gcc flags and linker script.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Although mips_io_port_base is currently a part of IDE command, it is quite
fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move
it to MIPS general part, and introduce `set_io_port_base()' from Linux.
This patch is triggered by multiple definition of `mips_io_port_base' build
error on gth2 (and tb0229 also needs this fix.)
board/gth2/libgth2.a(gth2.o): In function `log_serial_char':
/home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base'
common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here
make: *** [u-boot] Error 1
Wolfgang Denk [Sat, 17 Nov 2007 00:30:40 +0000 (01:30 +0100)]
Fix a bug in the slave serial programming mode for the Xilinx
Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if
the most significant bit was set, which did not work on any
architecture where "char" defaulted to be an unsigned type.
Based on a patch by Angelos Manousaridis <amanous@inaccessnetworks.com>
Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.
Stefan Roese [Fri, 16 Nov 2007 13:00:59 +0000 (14:00 +0100)]
ppc4xx: Update AMCC Makalu for board rev 1.1
This patch adds changes needed for Makalu rev 1.1:
- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup
Grant Likely [Mon, 24 Sep 2007 15:05:30 +0000 (09:05 -0600)]
Build: split COBJS value into multiple lines
This change is in preparation for condtitionial compile support in the
build system. By spliting them all into seperate lines now, subsequent
patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
be less invasive and easier to review
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
projects / karo-tx-uboot.git / log