]> git.karo-electronics.de Git - linux-beck.git/log
linux-beck.git
11 years agosfc: Reset driver's MAC stats after MC reboot seen
Ben Hutchings [Mon, 1 Oct 2012 19:58:35 +0000 (20:58 +0100)]
sfc: Reset driver's MAC stats after MC reboot seen

If the MC reboots then the stats it reports to us will have been
reset.  We need to reset ours to get efx_update_diff_stat() working
properly.

(Ideally we would maintain stats across the reboot, but as this should
only happen immediately after a firmware upgrade it's not really worth
the trouble.)

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Do not initialise buffer in efx_alloc_special_buffer()
Ben Hutchings [Tue, 18 Sep 2012 23:31:18 +0000 (00:31 +0100)]
sfc: Do not initialise buffer in efx_alloc_special_buffer()

Currently we initialise the newly allocated buffer to all-1s, which is
important for event queues but not for descriptor queues.  And since
we also do that in efx_nic_init_eventq(), it is completely pointless
to do it here.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Correctly initialise reset_method in siena_test_chip()
Ben Hutchings [Sat, 1 Dec 2012 01:55:27 +0000 (01:55 +0000)]
sfc: Correctly initialise reset_method in siena_test_chip()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Remove confusing MMIO functions
Ben Hutchings [Tue, 18 Sep 2012 00:56:50 +0000 (01:56 +0100)]
sfc: Remove confusing MMIO functions

efx_writed_table() uses a step of 16 bytes but efx_readd_table() uses
a step of 4 bytes.  Why are they different?

Firstly, register access is asymmetric:

- The EVQ_RPTR table and RX_INDIRECTION_TBL can (or must?) be written
  as dwords even though they have a step size of 16 bytes, unlike
  most other CSRs.
- In general, a read of any width is valid for registers, so long as
  it does not cross register boundaries.  There is also no latching
  behaviour in the BIU, contrary to rumour.

We write to the EVQ_RPTR table with efx_writed_table() but never read
it back as it's write-only.  We write to the RX_INDIRECTION_TBL with
efx_writed_table(), but only read it back for the register dump, where
we use efx_reado_table() as for any other table with step size of 16.

We read MC_TREG_SMEM with efx_readd_table() for the register dump, but
normally read and write it with efx_readd() and efx_writed() using
offsets calculated in bytes.

Since these functions are trivial and have few callers, it's clearer
to open-code them at the call sites.  While we're at it, update the
comments on the BIU behaviour again.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Fix check for failure of MC_CMD_FLUSH_RX_QUEUES
Ben Hutchings [Tue, 11 Sep 2012 17:25:13 +0000 (18:25 +0100)]
sfc: Fix check for failure of MC_CMD_FLUSH_RX_QUEUES

efx_mcdi_rpc_start() returns a negative value on error or zero on
success.  However one caller that can't properly handle failure then
does WARN_ON(rc > 0).  Change it to WARN_ON(rc < 0).

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Delete redundant page_addr variable from efx_init_rx_buffers_page()
Ben Hutchings [Thu, 6 Sep 2012 22:54:15 +0000 (23:54 +0100)]
sfc: Delete redundant page_addr variable from efx_init_rx_buffers_page()

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Really disable flow control while flushing
Ben Hutchings [Thu, 6 Sep 2012 15:52:31 +0000 (16:52 +0100)]
sfc: Really disable flow control while flushing

Receiving pause frames can block TX queue flushes.  Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Fix byte order warning in self-test
Ben Hutchings [Thu, 6 Sep 2012 01:11:06 +0000 (02:11 +0100)]
sfc: Fix byte order warning in self-test

Add necessary cast when setting a bogus checksum.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agosfc: Fix byte order warnings for ethtool RX filter interface
Ben Hutchings [Thu, 6 Sep 2012 01:11:04 +0000 (02:11 +0100)]
sfc: Fix byte order warnings for ethtool RX filter interface

sparse has got a bit more picky since I last ran it over this.  Add
forced casts for use of ~0 as a big-endian value.  Undo the pointless
optimisation of parameter validation with '|'; using '||' avoids these
warnings.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
11 years agocore: make GRO methods static.
Rami Rosen [Wed, 28 Nov 2012 21:55:25 +0000 (21:55 +0000)]
core: make GRO methods static.

This patch changes three methods to be static and removes their
EXPORT_SYMBOLs in core/dev.c and their external declaration in
netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and
napi_skb_finish(), which are in the GRO rx path, are not used
outside core/dev.c.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agodoc: make the description of how tcp_ecn works more explicit and clear
Rick Jones [Wed, 28 Nov 2012 09:53:10 +0000 (09:53 +0000)]
doc: make the description of how tcp_ecn works more explicit and clear

Make the description of how tcp_ecn works a bit more explicit and clear.

Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
David S. Miller [Thu, 29 Nov 2012 17:51:17 +0000 (12:51 -0500)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Thu, 29 Nov 2012 05:54:07 +0000 (21:54 -0800)]
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Pull networking fixes from David Miller:
 "Some more fixes trickled in over the past few days:

   1) PIM device names can overflow the IFNAMSIZ buffer unless we
      properly limit the allowed indexes, fix from Eric Dumazet.

   2) Under heavy load we can OOPS in icmp reply processing due to an
      unchecked inet_putpeer() call.  Fix from Neal Cardwell.

   3) SCTP round trip calculations need to use 64-bit math to avoid
      overflows, fix from Schoch Christian.

   4) Fix a memory leak and an error return flub in SCTP and IRDA
      triggerable by userspace.  Fix from Tommi Rantala and found by the
      syscall fuzzer (trinity).

   5) MLX4 driver gives bogus size to memcpy() call, fix from Amir
      Vadai.

   6) Fix length calculation in VHOST descriptor translation, from
      Michael S Tsirkin.

   7) Ambassador ATM driver loops forever while loading firmware, fix
      from Dan Carpenter.

   8) Over MTU packets in openvswitch warn about wrong device, fix from
      Jesse Gross.

   9) Netfilter IPSET's netlink code can overrun a string buffer because
      it's not properly limited to IFNAMSIZ.  Fix from Florian Westphal.

  10) PCAN USB driver sets wrong timestamp in SKB, from Oliver Hartkopp.

  11) Make sure the RX ifindex always has a valid value in the CAN BCM
      driver, even if we haven't received a frame yet.  Fix also from
      Oliver Hartkopp."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  team: fix hw_features setup
  atm: forever loop loading ambassador firmware
  vhost: fix length for cross region descriptor
  irda: irttp: fix memory leak in irttp_open_tsap() error path
  net: qmi_wwan: add Huawei E173
  net/mlx4_en: Can set maxrate only for TC0
  sctp: Error in calculation of RTTvar
  sctp: fix -ENOMEM result with invalid user space pointer in sendto() syscall
  sctp: fix memory leak in sctp_datamsg_from_user() when copy from user space fails
  net: ipmr: limit MRT_TABLE identifiers
  ipv4: avoid passing NULL to inet_putpeer() in icmpv4_xrlim_allow()
  can: bcm: initialize ifindex for timeouts without previous frame reception
  can: peak_usb: fix hwtstamp assignment
  netfilter: ipset: fix netiface set name overflow
  openvswitch: Store flow key len if ARP opcode is not request or reply.
  openvswitch: Print device when warning about over MTU packets.

11 years agoMerge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
David S. Miller [Wed, 28 Nov 2012 23:00:47 +0000 (18:00 -0500)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch

Two small openswitch fixes from Jesse Gross.

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: ethernet: cpsw: fix build warnings for CPSW when CPTS not selected
Mugunthan V N [Tue, 27 Nov 2012 07:53:40 +0000 (07:53 +0000)]
net: ethernet: cpsw: fix build warnings for CPSW when CPTS not selected

CC      drivers/net/ethernet/ti/cpsw.o
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_ndo_ioctl':
drivers/net/ethernet/ti/cpsw.c:881:20: warning: unused variable 'priv'

The build warning is generated when CPTS is not selected in Kernel Build.
Fixing by passing the net_device pointer to cpts IOCTL instead of passing priv

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville...
David S. Miller [Wed, 28 Nov 2012 22:49:16 +0000 (17:49 -0500)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
This pull request is intended for the 3.8 stream.  It is a bit large
-- I guess Thanksgiving got me off track!  At least the code got to
spend some time in linux-next... :-)

This includes the usual batch of pulls for Bluetooth, NFC, and mac80211
as well as iwlwifi.  Also here is an ath6kl pull, and a new driver
in the rtlwifi family.  The brcmfmac, brcmsmac, ath9k, and mwl8k get
their usual levels of attention, and a handful of other updates tag
along as well.

For more detail on the pulls, please see below...

On Bluetooth, Gustavo says:

"Another set of patches for integration in wireless-next. There are two big set
of changes in it: Andrei Emeltchenko and Mat Martineau added more patches
towards a full Bluetooth High Speed support and Johan Hedberg improve the
single mode support for Bluetooth dongles. Apart from that we have small fixes
and improvements."

...and:

"A few patches to 3.8. The majority of the work here is from Andrei on the High
Speed support. Other than that Johan added support for setting LE advertising
data. The rest are fixes and clean ups and small improvements like support for
a new broadcom hardware."

On mac80211, Johannes says:

"This is for mac80211, for -next (3.8). Plenty of changes, as you can see
below. Some fixes for previous changes like the export.h include, the
beacon listener fix from Ben Greear, etc. Overall, no exciting new
features, though hwsim does gain channel context support for people to
try it out and look at."

...and...:

"This one contains the mac80211-next material. Apart from a few small new
features and cleanups I have two fixes for the channel context code. The
RX_END timestamp support will probably be reworked again as Simon Barber
noted the calculations weren't really valid, but the discussions there
are still going on and it's better than what we had before."

...and:

"Please pull (see below) to get the following changes:
 * a fix & a debug aid in IBSS from Antonio,
 * mesh cleanups from Marco,
 * a few bugfixes for some of my previous patches from Arend and myself,
 * and the big initial VHT support patchset"

And on iwlwifi, Johannes says:

"In addition to the previous four patches that I'm not resending,
we have a number of cleanups, message reduction, firmware error
handling improvements (yes yes... we need to fix them instead)
and various other small things all over."

...and:

"In his quest to try to understand the current iwlwifi problems (like
stuck queues etc.) Emmanuel has first cleaned up the PCIe code, I'm
including his changes in this pull request. Other than that I only have
a small cleanup from Sachin Kamat to remove a duplicate include and a
bugfix to turn off MFP if software crypto is enabled, but this isn't
really interesting as MFP isn't supported right now anyway."

On NFC, Samuel says:

"With this one we have:

- A few HCI improvements in preparation for an upcoming HCI chipset support.
- A pn544 code cleanup after the old driver was removed.
- An LLCP improvement for notifying user space when one peer stops ACKing I
  frames."

On ath6kl, Kalle says:

"Major changes this time are firmware recover support to gracefully
handle if firmware crashes, support for changing regulatory domain and
support for new ar6004 hardware revision 1.4. Otherwise there are just
smaller fixes or cleanups from different people."

Thats about it... :-)  Please let me know if there are problems!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocxgb3: Restore dependency on INET
Ben Hutchings [Wed, 28 Nov 2012 20:03:03 +0000 (20:03 +0000)]
cxgb3: Restore dependency on INET

Commit ff33c0e1885cda44dd14c79f70df4706f83582a0 ('net: Remove bogus
dependencies on INET') wrongly removed this dependency.  cxgb3 uses
the arp_send() function defined in net/ipv4/arp.c.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoteam: fix hw_features setup
Jiri Pirko [Wed, 28 Nov 2012 06:13:10 +0000 (06:13 +0000)]
team: fix hw_features setup

Do this in the same way bonding does. This fixed setup resolves performance
issues when using some cards with certain offloading.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoatm: forever loop loading ambassador firmware
Dan Carpenter [Tue, 27 Nov 2012 07:29:35 +0000 (07:29 +0000)]
atm: forever loop loading ambassador firmware

There was a forever loop introduced here when we converted this to
request_firmware() back in 2008.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoip6tnl/sit: drop packet if ECN present with not-ECT
Nicolas Dichtel [Tue, 27 Nov 2012 03:07:11 +0000 (03:07 +0000)]
ip6tnl/sit: drop packet if ECN present with not-ECT

This patch reports the change made by Stephen Hemminger in ipip and gre[6] in
commit eccc1bb8d4b4 (tunnel: drop packet if ECN present with not-ECT).

Goal is to handle RFC6040, Section 4.2:

Default Tunnel Egress Behaviour.
 o If the inner ECN field is Not-ECT, the decapsulator MUST NOT
      propagate any other ECN codepoint onwards.  This is because the
      inner Not-ECT marking is set by transports that rely on dropped
      packets as an indication of congestion and would not understand or
      respond to any other ECN codepoint [RFC4774].  Specifically:

      *  If the inner ECN field is Not-ECT and the outer ECN field is
         CE, the decapsulator MUST drop the packet.

      *  If the inner ECN field is Not-ECT and the outer ECN field is
         Not-ECT, ECT(0), or ECT(1), the decapsulator MUST forward the
         outgoing packet with the ECN field cleared to Not-ECT.

The patch takes benefits from common function added in net/inet_ecn.h.

Like it was done for Xin4 tunnels, it adds logging to allow detecting broken
systems that set ECN bits incorrectly when tunneling (or an intermediate
router might be changing the header). Errors are also tracked via
rx_frame_error.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobe2net: fix INTx ISR for interrupt behaviour on BE2
Sathya Perla [Tue, 27 Nov 2012 19:50:02 +0000 (19:50 +0000)]
be2net: fix INTx ISR for interrupt behaviour on BE2

On BE2 chip, an interrupt may be raised even when EQ is in un-armed state.
As a result be_intx()::events_get() and be_poll:events_get() can race and
notify an EQ wrongly.

Fix this by counting events only in be_poll(). Commit 0b545a629 fixes
the same issue in the MSI-x path.

But, on Lancer, INTx can be de-asserted only by notifying num evts. This
is not an issue as the above BE2 behavior doesn't exist/has never been
seen on Lancer.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoewrk3: remove outdated comment
Paul Bolle [Mon, 26 Nov 2012 23:48:34 +0000 (23:48 +0000)]
ewrk3: remove outdated comment

Remove an outdated comment, that should have been removed in the
patch named "MODULE_PARM conversions" from early 2005.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoewrk3: silence GCC warning
Paul Bolle [Mon, 26 Nov 2012 23:47:17 +0000 (23:47 +0000)]
ewrk3: silence GCC warning

Building ewrk3.o triggers this GCC warning:
    drivers/net/ethernet/dec/ewrk3.c: In function '__check_irq':
    drivers/net/ethernet/dec/ewrk3.c:1915:1: warning: return from incompatible pointer type [enabled by default]

This can be trivially fixed by changing the 'irq' parameter from int to
byte (which is an alias for unsigned char for module parameters).

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next
David S. Miller [Wed, 28 Nov 2012 16:30:57 +0000 (11:30 -0500)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next

Marc Kleine-Budde says:

====================
this is pull request is for net-next. Contains a patch by Andreas
Larsson, which enables the sja1000 of driver to work under sparc.
AnilKumar Ch contributed a patch to improve the c_can support under
omap, Olivier Sobrie's patch brings support for the CAN/USB dongles
from Kvaser. In a bunch of patches by me missing MODULE_ALIAS and/or
MODULE_DEVICE_TABLE entries were added to the CAN drivers.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://1984.lsi.us.es/nf
David S. Miller [Wed, 28 Nov 2012 16:29:43 +0000 (11:29 -0500)]
Merge branch 'master' of git://1984.lsi.us.es/nf

An interface name overflow fix in netfilter via Pablo Neira Ayuso.

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobonding: in balance-rr mode, set curr_active_slave only if it is up
Michal Kubeček [Thu, 22 Nov 2012 02:48:39 +0000 (02:48 +0000)]
bonding: in balance-rr mode, set curr_active_slave only if it is up

If all slaves of a balance-rr bond with ARP monitor are enslaved
with down link state, bond keeps down state even after slaves
go up.

This is caused by bond_enslave() setting curr_active_slave to
first slave not taking into account its link state. As
bond_loadbalance_arp_mon() uses curr_active_slave to identify
whether slave's down->up transition should update bond's link
state, bond stays down even if slaves are up (until first slave
goes from up to down at least once).

Before commit f31c7937 "bonding: start slaves with link down for
ARP monitor", this was masked by slaves always starting in UP
state with ARP monitor (and MII monitor not relying on
curr_active_slave being NULL if there is no slave up).

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovhost: fix length for cross region descriptor
Michael S. Tsirkin [Mon, 26 Nov 2012 05:57:27 +0000 (05:57 +0000)]
vhost: fix length for cross region descriptor

If a single descriptor crosses a region, the
second chunk length should be decremented
by size translated so far, instead it includes
the full descriptor length.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoirda: irttp: fix memory leak in irttp_open_tsap() error path
Tommi Rantala [Mon, 26 Nov 2012 04:16:44 +0000 (04:16 +0000)]
irda: irttp: fix memory leak in irttp_open_tsap() error path

Cleanup the memory we allocated earlier in irttp_open_tsap() when we hit
this error path. The leak goes back to at least 1da177e4
("Linux-2.6.12-rc2").

Discovered with Trinity (the syscall fuzzer).

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: qmi_wwan: add Huawei E173
Bjørn Mork [Sun, 25 Nov 2012 06:03:59 +0000 (06:03 +0000)]
net: qmi_wwan: add Huawei E173

The Huawei E173 is a QMI/wwan device which normally appear
as 12d1:1436 in Linux. The descriptors displayed in that
mode will be picked up by cdc_ether.  But the modem has
another mode with a different device ID and a slightly
different set of descriptors. This is the mode used by
Windows like this:

3Modem:      USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003

Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agopkt_sched: QFQ Plus: fair-queueing service at DRR cost
Paolo Valente [Fri, 23 Nov 2012 11:03:19 +0000 (11:03 +0000)]
pkt_sched: QFQ Plus: fair-queueing service at DRR cost

This patch turns QFQ into QFQ+, a variant of QFQ that provides the
following two benefits: 1) QFQ+ is faster than QFQ, 2) differently
from QFQ, QFQ+ correctly schedules also non-leaves classes in a
hierarchical setting. A detailed description of QFQ+, plus a
performance comparison with DRR and QFQ, can be found in [1].

[1] P. Valente, "Reducing the Execution Time of Fair-Queueing Schedulers"
http://algo.ing.unimo.it/people/paolo/agg-sched/agg-sched.pdf

Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: don't enable remote wakeup directly
Steve Glendinning [Wed, 28 Nov 2012 05:59:50 +0000 (05:59 +0000)]
smsc75xx: don't enable remote wakeup directly

As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: add support for USB dynamic autosuspend
Steve Glendinning [Wed, 28 Nov 2012 05:59:49 +0000 (05:59 +0000)]
smsc75xx: add support for USB dynamic autosuspend

This patch adds support for USB dynamic autosuspend to the
smsc75xx driver.  This saves virtually no power in the USB
device but enables power savings in upstream hosts and
the host CPU.

Note currently Linux doesn't automatically enable this
functionality by default for devices so to test this:

 echo auto > /sys/bus/usb/devices/2-1.2/power/control

where 2-1.2 is the USB bus address of the LAN7500.

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: fix error handling in suspend failure case
Steve Glendinning [Wed, 28 Nov 2012 05:59:48 +0000 (05:59 +0000)]
smsc75xx: fix error handling in suspend failure case

This patch ensures that if we fail to suspend the LAN7500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: support PHY wakeup source
Steve Glendinning [Wed, 28 Nov 2012 05:59:47 +0000 (05:59 +0000)]
smsc75xx: support PHY wakeup source

This patch enables LAN7500 family devices to wake from suspend
on either link up or link down events.

It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions

Updated patch to add newlines to printk messages

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: refactor entering suspend modes
Steve Glendinning [Wed, 28 Nov 2012 05:59:46 +0000 (05:59 +0000)]
smsc75xx: refactor entering suspend modes

This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc75xx_suspend function.

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmsc75xx: check return code from smsc75xx_reset
Steve Glendinning [Wed, 28 Nov 2012 05:59:45 +0000 (05:59 +0000)]
smsc75xx: check return code from smsc75xx_reset

This patch adds a missing check and error message if smsc75xx_reset
fails.

Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/mlx4_en: Can set maxrate only for TC0
Amir Vadai [Wed, 28 Nov 2012 11:43:15 +0000 (13:43 +0200)]
net/mlx4_en: Can set maxrate only for TC0

Had a typo in memcpy.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosctp: Error in calculation of RTTvar
Schoch Christian [Wed, 28 Nov 2012 05:18:29 +0000 (05:18 +0000)]
sctp: Error in calculation of RTTvar

The calculation of RTTVAR involves the subtraction of two unsigned
numbers which
may causes rollover and results in very high values of RTTVAR when RTT > SRTT.
With this patch it is possible to set RTOmin = 1 to get the minimum of RTO at
4 times the clock granularity.

Change Notes:

v2)
        *Replaced abs() by abs64() and long by __s64, changed patch
description.

Signed-off-by: Christian Schoch <e0326715@student.tuwien.ac.at>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: linux-sctp@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosctp: fix -ENOMEM result with invalid user space pointer in sendto() syscall
Tommi Rantala [Thu, 22 Nov 2012 03:23:16 +0000 (03:23 +0000)]
sctp: fix -ENOMEM result with invalid user space pointer in sendto() syscall

Consider the following program, that sets the second argument to the
sendto() syscall incorrectly:

 #include <string.h>
 #include <arpa/inet.h>
 #include <sys/socket.h>

 int main(void)
 {
         int fd;
         struct sockaddr_in sa;

         fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
         if (fd < 0)
                 return 1;

         memset(&sa, 0, sizeof(sa));
         sa.sin_family = AF_INET;
         sa.sin_addr.s_addr = inet_addr("127.0.0.1");
         sa.sin_port = htons(11111);

         sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));

         return 0;
 }

We get -ENOMEM:

 $ strace -e sendto ./demo
 sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 ENOMEM (Cannot allocate memory)

Propagate the error code from sctp_user_addto_chunk(), so that we will
tell user space what actually went wrong:

 $ strace -e sendto ./demo
 sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 EFAULT (Bad address)

Noticed while running Trinity (the syscall fuzzer).

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosctp: fix memory leak in sctp_datamsg_from_user() when copy from user space fails
Tommi Rantala [Tue, 27 Nov 2012 04:01:46 +0000 (04:01 +0000)]
sctp: fix memory leak in sctp_datamsg_from_user() when copy from user space fails

Trinity (the syscall fuzzer) discovered a memory leak in SCTP,
reproducible e.g. with the sendto() syscall by passing invalid
user space pointer in the second argument:

 #include <string.h>
 #include <arpa/inet.h>
 #include <sys/socket.h>

 int main(void)
 {
         int fd;
         struct sockaddr_in sa;

         fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
         if (fd < 0)
                 return 1;

         memset(&sa, 0, sizeof(sa));
         sa.sin_family = AF_INET;
         sa.sin_addr.s_addr = inet_addr("127.0.0.1");
         sa.sin_port = htons(11111);

         sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));

         return 0;
 }

As far as I can tell, the leak has been around since ~2003.

Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: fix coding style issues in qlcnic_minidump.c
Sony Chacko [Wed, 28 Nov 2012 04:34:31 +0000 (04:34 +0000)]
qlcnic: fix coding style issues in qlcnic_minidump.c

Fix coding style violations in qlcnic_minidump.c

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: create file qlcnic_minidump.c for dump utility
Sony Chacko [Wed, 28 Nov 2012 04:34:30 +0000 (04:34 +0000)]
qlcnic: create file qlcnic_minidump.c for dump utility

Physical refactoring of 82xx adapter register dump utility.

Move register dump routines to new file qlcnic_minidump.c
Existing register dump routines has coding style issues, the code
is moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_minidump.c

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: fix style issues in qlcnic_sysfs.c file
Sony Chacko [Wed, 28 Nov 2012 04:34:29 +0000 (04:34 +0000)]
qlcnic: fix style issues in qlcnic_sysfs.c file

Fix coding style issues in qlcnic_sysfs.c file

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: create file qlcnic_sysfs.c for sysfs routines
Sony Chacko [Wed, 28 Nov 2012 04:34:28 +0000 (04:34 +0000)]
qlcnic: create file qlcnic_sysfs.c for sysfs routines

Physical refactoring of 82xx adapter sysfs routines.

Move sysfs routines to new file qlcnic_sysfs.c
Existing sysfs routines has coding style issues, this code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_sysfs.c

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: fix coding style issues in qlcnic_io.c
Sony Chacko [Wed, 28 Nov 2012 04:34:27 +0000 (04:34 +0000)]
qlcnic: fix coding style issues in qlcnic_io.c

Fix coding style issues in qlcnic_io.c

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlcnic: create file qlcnic_io.c for datapath routines
Sony Chacko [Wed, 28 Nov 2012 04:34:26 +0000 (04:34 +0000)]
qlcnic: create file qlcnic_io.c for datapath routines

Physical refactoring of 82xx adapter data path routines.

Move data path code to new file qlcnic_io.c
Existing data path code has coding stye issues, the code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_io.c

Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net...
David S. Miller [Wed, 28 Nov 2012 16:05:00 +0000 (11:05 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to igb, igbvf and ixgbe.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Change duplex setting in EEE function
Yaniv Rosner [Tue, 27 Nov 2012 03:46:36 +0000 (03:46 +0000)]
bnx2x: Change duplex setting in EEE function

This is not a real problem, since the EEE is supported for devices where the
actual_phy_selection is zero, such that the req_duplex of params will match
the one of the phy struct.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Add warning message in case of non-10G SFP module
Yaniv Rosner [Tue, 27 Nov 2012 03:46:35 +0000 (03:46 +0000)]
bnx2x: Add warning message in case of non-10G SFP module

The string was split to several lines since it reached over 180 chars, which
seems too much.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Cosmetic changes
Yaniv Rosner [Tue, 27 Nov 2012 03:46:34 +0000 (03:46 +0000)]
bnx2x: Cosmetic changes

This patch makes some cosmetic changes to the code:
1. Code alignment.
2. Merge read-modify-write into a single function (read_or_write /
read_and_write).
3. Merge several write registers into a for-loop write using a static array.
4. Remove empty lines.
5. Fix comments.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Always take PHY lock
Yaniv Rosner [Tue, 27 Nov 2012 03:46:33 +0000 (03:46 +0000)]
bnx2x: Always take PHY lock

Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.

Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Add support for BCM84834
Yaniv Rosner [Tue, 27 Nov 2012 03:46:32 +0000 (03:46 +0000)]
bnx2x: Add support for BCM84834

Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Fix SFP+ current leakage
Yaniv Rosner [Tue, 27 Nov 2012 03:46:31 +0000 (03:46 +0000)]
bnx2x: Fix SFP+ current leakage

Per measurements, the SFP+ suffered from small current leakage in two cases:
 - When no module was plugged and TX laser was disabled. The fix was to enable
   it, and when module is plugged in, check if it needs to be disabled.
 - When over-current event occurs due to invalid SFP+ module, the HW basically
   shuts down the current for this module, but the SW needs to complete this
   by issuing a power down via a GPIO.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Change MDIO clock settings
Yaniv Rosner [Tue, 27 Nov 2012 03:46:30 +0000 (03:46 +0000)]
bnx2x: Change MDIO clock settings

When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Add support for 20G-KR2
Yaniv Rosner [Tue, 27 Nov 2012 03:46:29 +0000 (03:46 +0000)]
bnx2x: Add support for 20G-KR2

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2x: Activate LFA
Yaniv Rosner [Tue, 27 Nov 2012 03:46:28 +0000 (03:46 +0000)]
bnx2x: Activate LFA

In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
John W. Linville [Wed, 28 Nov 2012 15:56:03 +0000 (10:56 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c

11 years agopercpu-rwsem: use synchronize_sched_expedited
Mikulas Patocka [Wed, 28 Nov 2012 03:59:52 +0000 (22:59 -0500)]
percpu-rwsem: use synchronize_sched_expedited

Use synchronize_sched_expedited() instead of synchronize_sched()
to improve mount speed.

This patch improves mount time from 0.500s to 0.013s for Jeff's
test-case.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoixgbe: bump version number
Don Skidmore [Fri, 9 Nov 2012 05:03:53 +0000 (05:03 +0000)]
ixgbe: bump version number

Move the version string to better reflect the driver functionality with
that of the out of tree driver.  Also since we no longer need the MAJ,
MIN, BUILD defines remove them to clean up the code.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoixgbe: Make the bridge mode setting sticky
Greg Rose [Thu, 8 Nov 2012 02:41:35 +0000 (02:41 +0000)]
ixgbe: Make the bridge mode setting sticky

The internal bridge mode setting needs to be sticky so that it can be
configured correctly after a device reset.  This change is required now
that the driver supports setting the bridge mode to VEB or VEPA.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoixgbe: Fix incorrect disabling of Tx hang check in case of PFC
Parikh, Neerav [Thu, 27 Sep 2012 12:02:22 +0000 (12:02 +0000)]
ixgbe: Fix incorrect disabling of Tx hang check in case of PFC

The XOFF received statistic registers are per priority based and not per
traffic class. The ixgbe driver was incorrectly considering them to be for
each traffic class; and then disabling the "Tx hang" check for the queues
that belonged to the particular traffic class that had received PFC frames.

The above logic worked fine in scenario where the user priority and traffic
class number matched e.g. priority 0 is mapped to traffic class 0 and so on.
But, when multiple user priorities are mapped to a single traffic class or
when user priorities and traffic class numbers do not line up; the ixgbe
driver may disable the "Tx hang" check for queues belonging to a traffic
class that did not receive PFC frames and keep the "Tx hang" check enabled
for the queues that did receive the PFC frames.

This patch corrects the above in the code by considering the statistics
on a per priority basis; then getting the traffic class the user priority
belongs to and disabling the "Tx hang" check for queues that belong
to that traffic class.

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoixgbe: Drop RLPML configuration from x540 RXDCTL register configuration
Alexander Duyck [Sat, 8 Sep 2012 02:13:38 +0000 (02:13 +0000)]
ixgbe: Drop RLPML configuration from x540 RXDCTL register configuration

Since we are doing a page based receive there is no point in setting a maximum
packet length on the x540 RXDCTL register.  As such we can drop the code from
the driver entirely.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoigb: Use a 32-bit mask when calculating the flow control watermarks
Matthew Vick [Thu, 8 Nov 2012 04:03:58 +0000 (04:03 +0000)]
igb: Use a 32-bit mask when calculating the flow control watermarks

For some devices, the result of the flow control high watermark gets
truncated when programming it into the registers because of the mask used.
Switch the mask to 32-bit to prevent this from happening.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoigbvf: update version number
Mitch A Williams [Sat, 17 Nov 2012 07:10:16 +0000 (07:10 +0000)]
igbvf: update version number

Update version number.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoigbvf: work around i350 erratum
Mitch A Williams [Sat, 17 Nov 2012 07:10:16 +0000 (07:10 +0000)]
igbvf: work around i350 erratum

On i350 VF devices, VLAN tags will be byte-swapped in the receive
descriptor only when received packets are looped back from other
VFs. Check for this condition and swab the tag if needed.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
11 years agoMerge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab...
Linus Torvalds [Tue, 27 Nov 2012 20:27:37 +0000 (12:27 -0800)]
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media fixes from Mauro Carvalho Chehab:
 "For some media fixes:
   - dvb_usb_v2: some fixes at the core
   - Some fixes on some embedded drivers: soc_camera, adv7604, omap3isp,
     exynos/s5p
   - Several Exynos4/5 camera fixes
   - a fix at stv0900 driver
   - a few USB ID additions to detect more variants of rtl28xxu-based
     sticks"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
  [media] rtl28xxu: 0ccd:00d7 TerraTec Cinergy T Stick+
  [media] rtl28xxu: 1d19:1102 Dexatek DK mini DVB-T Dongle
  [media] mt9v022: fix the V4L2_CID_EXPOSURE control
  [media] mx2_camera: fix missing unlock on error in mx2_start_streaming()
  [media] media: omap1_camera: fix const cropping related warnings
  [media] media: mx1_camera: use the default .set_crop() implementation
  [media] media: mx2_camera: fix const cropping related warnings
  [media] media: mx3_camera: fix const cropping related warnings
  [media] media: pxa_camera: fix const cropping related warnings
  [media] media: sh_mobile_ceu_camera: fix const cropping related warnings
  [media] media: sh_vou: fix const cropping related warnings
  [media] adv7604: restart STDI once if format is not found
  [media] adv7604: use presets where possible
  [media] adv7604: Replace prim_mode by mode
  [media] adv7604: cleanup references
  [media] dvb_usb_v2: switch interruptible mutex to normal
  [media] dvb_usb_v2: fix pid_filter callback error logging
  [media] exynos-gsc: change driver compatible string
  [media] omap3isp: Fix warning caused by bad subdev events operations prototypes
  [media] omap3isp: video: Fix warning caused by bad vidioc_s_crop prototype
  ...

11 years agocan: mpc5xxx_can: add MODULE_DEVICE_TABLE
Marc Kleine-Budde [Fri, 12 Oct 2012 08:19:27 +0000 (10:19 +0200)]
can: mpc5xxx_can: add MODULE_DEVICE_TABLE

This patch adds a MODULE_DEVICE_TABLE for the of bindings, so that the module
can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: c_can_platform: add MODULE_DEVICE_TABLE
Marc Kleine-Budde [Fri, 12 Oct 2012 07:48:06 +0000 (09:48 +0200)]
can: c_can_platform: add MODULE_DEVICE_TABLE

This patch adds a MODULE_DEVICE_TABLE for the of and platform bindings, so that
the module can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: at91_can: add MODULE_DEVICE_TABLE
Marc Kleine-Budde [Fri, 12 Oct 2012 07:44:51 +0000 (09:44 +0200)]
can: at91_can: add MODULE_DEVICE_TABLE

This patch adds a MODULE_DEVICE_TABLE for the platform bindings, so that the
module can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: flexcan: add MODULE_DEVICE_TABLE
Marc Kleine-Budde [Thu, 4 Oct 2012 08:55:35 +0000 (10:55 +0200)]
can: flexcan: add MODULE_DEVICE_TABLE

This patch adds a MODULE_DEVICE_TABLE for the of and platform bindings, so that
the module can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: cc770_platform: add MODULE_ALIAS and MODULE_DEVICE_TABLE
Marc Kleine-Budde [Fri, 12 Oct 2012 07:51:19 +0000 (09:51 +0200)]
can: cc770_platform: add MODULE_ALIAS and MODULE_DEVICE_TABLE

This patch adds a MODULE_ALIAS for the platform bindings and a
MODULE_DEVICE_TABLE for of bindings, so that the module can be loaded
automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: sja1000_platform: add MODULE_ALIAS
Marc Kleine-Budde [Fri, 12 Oct 2012 07:45:14 +0000 (09:45 +0200)]
can: sja1000_platform: add MODULE_ALIAS

This patch adds a MODULE_ALIAS for the platform bindings, so that the module
can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: ti_hecc: add MODULE_ALIAS
Marc Kleine-Budde [Mon, 29 Oct 2012 13:18:04 +0000 (14:18 +0100)]
can: ti_hecc: add MODULE_ALIAS

This patch adds a MODULE_ALIAS for the platform bindings, so that
the module can be loaded automatically udev.

Tested-by: Jan Lübbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: bfin_can: add MODULE_ALIAS
Marc Kleine-Budde [Fri, 12 Oct 2012 07:45:14 +0000 (09:45 +0200)]
can: bfin_can: add MODULE_ALIAS

This patch adds a MODULE_ALIAS for the platform bindings, so that the module
can be loaded automatically by udev.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: sja1000: Make sja1000_of_platform selectable and compilable on SPARC
Andreas Larsson [Thu, 4 Oct 2012 13:59:10 +0000 (15:59 +0200)]
can: sja1000: Make sja1000_of_platform selectable and compilable on SPARC

Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: kvaser_usb: Add support for Kvaser CAN/USB devices
Olivier Sobrie [Wed, 21 Nov 2012 07:11:13 +0000 (08:11 +0100)]
can: kvaser_usb: Add support for Kvaser CAN/USB devices

This driver provides support for several Kvaser CAN/USB devices.
Such kind of devices supports up to three CAN network interfaces.

It has been tested with a Kvaser USB Leaf Light (one network interface)
connected to a pch_can interface.
The firmware version of the Kvaser device was 2.5.205.

List of Kvaser devices supported by the driver:
  - Kvaser Leaf Light
  - Kvaser Leaf Professional HS
  - Kvaser Leaf SemiPro HS
  - Kvaser Leaf Professional LS
  - Kvaser Leaf Professional SWC
  - Kvaser Leaf Professional LIN
  - Kvaser Leaf SemiPro LS
  - Kvaser Leaf SemiPro SWC
  - Kvaser Memorator II HS/HS
  - Kvaser USBcan Professional HS/HS
  - Kvaser Leaf Light GI
  - Kvaser Leaf Professional HS (OBD-II connector)
  - Kvaser Memorator Professional HS/LS
  - Kvaser Leaf Light "China"
  - Kvaser BlackBird SemiPro
  - Kvaser USBcan R

Signed-off-by: Daniel Berglund <db@kvaser.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agocan: c_can: Add d_can raminit support
AnilKumar Ch [Wed, 21 Nov 2012 05:44:10 +0000 (11:14 +0530)]
can: c_can: Add d_can raminit support

Add D_CAN raminit support to C_CAN driver to enable D_CAN RAM,
which holds all the message objects during transmission or
receiving of data. This initialization/de-initialization should
be done in synchronous with D_CAN clock.

In case of AM335X-EVM (current user of D_CAN driver) message RAM is
controlled through control module register for both instances. So
control module register details is required to initialization or
de-initialization of message RAM according to instance number.

Control module memory resource is obtained from D_CAN dt node and
instance number obtained from device tree aliases node.

This patch was tested on AM335x-EVM along with pinctrl data addition
patch, d_can dt aliases addition and control module data addition.
pinctrl data addition is not added to am335x-evm.dts (only supports
CPLD profile#0) because d_can1 is supported under CPLD profile#1.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[mkl: fix instance for non DT in probe, cleaned up raminit]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
11 years agoMerge branch 'akpm' (Fixes from Andrew)
Linus Torvalds [Tue, 27 Nov 2012 02:33:33 +0000 (18:33 -0800)]
Merge branch 'akpm' (Fixes from Andrew)

Merge misc fixes from Andrew Morton:
 "8 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
  futex: avoid wake_futex() for a PI futex_q
  watchdog: using u64 in get_sample_period()
  writeback: put unused inodes to LRU after writeback completion
  mm: vmscan: check for fatal signals iff the process was throttled
  Revert "mm: remove __GFP_NO_KSWAPD"
  proc: check vma->vm_file before dereferencing
  UAPI: strip the _UAPI prefix from header guards during header installation
  include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID

11 years agoMerge tag 'tty-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Linus Torvalds [Tue, 27 Nov 2012 01:46:36 +0000 (17:46 -0800)]
Merge tag 'tty-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull TTY fix from Greg Kroah-Hartman:
 "Here is a single fix for a reported regression in 3.7-rc5 for the tty
  layer.  This fix has been in the linux-next tree and solves the
  reported problem.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty vt: Fix a regression in command line edition

11 years agoMerge tag 'mfd-for-linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo...
Linus Torvalds [Tue, 27 Nov 2012 01:45:16 +0000 (17:45 -0800)]
Merge tag 'mfd-for-linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFD fixes from Samuel Ortiz:

 - A twl fix preventing a buffer overflow.

 - A wm5102 register patch fix.

 - A wm5110 error misreport fix.

 - Arizona fixes: Use the right array size when adding subdevices,
   correctly report underclocked events, synchronize register cache
   after reset.

 - A twl4030 fix for preventing the system to hang from an interrupt
   flood.

* tag 'mfd-for-linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: twl4030: Fix chained irq handling on resume from suspend
  mfd: arizona: Sync regcache after reset
  mfd: arizona: Correctly report when AIF2/AIF1 is underclocked
  mfd: arizona: Use correct array for ARRAY_SIZE in mfd_add_devices call
  mfd: wm5110: Disable control interface error report for WM5110 rev B
  mfd: wm5102: Update register patch for latest evaluation
  mfd: twl-core: Fix chip ID for the twl6030-pwm module

11 years agoMerge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Linus Torvalds [Tue, 27 Nov 2012 01:43:10 +0000 (17:43 -0800)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm

Pull ARM fixes from Russell King:
 "Not much here, just a couple minor/cosmetic fixes and a patch for the
  decompressor which fixes problems with modern GCC and CPUs."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7583/1: decompressor: Enable unaligned memory access for v6 and above
  ARM: 7572/1: proc-v6.S: fix comment
  ARM: 7570/1: quiet down the non make -s output

11 years agoMerge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Linus Torvalds [Tue, 27 Nov 2012 01:42:07 +0000 (17:42 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs

Pull ext3 regression fix from Jan Kara:
 "Fix an ext3 regression introduced during 3.7 merge window.  It leads
  to deadlock if you stress the filesystem in the right way (luckily
  only if blocksize < pagesize)."

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  jbd: Fix lock ordering bug in journal_unmap_buffer()

11 years agofutex: avoid wake_futex() for a PI futex_q
Darren Hart [Tue, 27 Nov 2012 00:29:56 +0000 (16:29 -0800)]
futex: avoid wake_futex() for a PI futex_q

Dave Jones reported a bug with futex_lock_pi() that his trinity test
exposed.  Sometime between queue_me() and taking the q.lock_ptr, the
lock_ptr became NULL, resulting in a crash.

While futex_wake() is careful to not call wake_futex() on futex_q's with
a pi_state or an rt_waiter (which are either waiting for a
futex_unlock_pi() or a PI futex_requeue()), futex_wake_op() and
futex_requeue() do not perform the same test.

Update futex_wake_op() and futex_requeue() to test for q.pi_state and
q.rt_waiter and abort with -EINVAL if detected.  To ensure any future
breakage is caught, add a WARN() to wake_futex() if the same condition
is true.

This fix has seen 3 hours of testing with "trinity -c futex" on an
x86_64 VM with 4 CPUS.

[akpm@linux-foundation.org: tidy up the WARN()]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: Dave Jones <davej@redat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: John Kacur <jkacur@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agowatchdog: using u64 in get_sample_period()
Chuansheng Liu [Tue, 27 Nov 2012 00:29:54 +0000 (16:29 -0800)]
watchdog: using u64 in get_sample_period()

In get_sample_period(), unsigned long is not enough:

  watchdog_thresh * 2 * (NSEC_PER_SEC / 5)

case1:
  watchdog_thresh is 10 by default, the sample value will be: 0xEE6B2800

case2:
 set watchdog_thresh is 20, the sample value will be: 0x1 DCD6 5000

In case2, we need use u64 to express the sample period.  Otherwise,
changing the threshold thru proc often can not be successful.

Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agowriteback: put unused inodes to LRU after writeback completion
Jan Kara [Tue, 27 Nov 2012 00:29:51 +0000 (16:29 -0800)]
writeback: put unused inodes to LRU after writeback completion

Commit 169ebd90131b ("writeback: Avoid iput() from flusher thread")
removed iget-iput pair from inode writeback.  As a side effect, inodes
that are dirty during iput_final() call won't be ever added to inode LRU
(iput_final() doesn't add dirty inodes to LRU and later when the inode
is cleaned there's noone to add the inode there).  Thus inodes are
effectively unreclaimable until someone looks them up again.

The practical effect of this bug is limited by the fact that inodes are
pinned by a dentry for long enough that the inode gets cleaned.  But
still the bug can have nasty consequences leading up to OOM conditions
under certain circumstances.  Following can easily reproduce the
problem:

  for (( i = 0; i < 1000; i++ )); do
    mkdir $i
    for (( j = 0; j < 1000; j++ )); do
      touch $i/$j
      echo 2 > /proc/sys/vm/drop_caches
    done
  done

then one needs to run 'sync; ls -lR' to make inodes reclaimable again.

We fix the issue by inserting unused clean inodes into the LRU after
writeback finishes in inode_sync_complete().

Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agomm: vmscan: check for fatal signals iff the process was throttled
Mel Gorman [Tue, 27 Nov 2012 00:29:48 +0000 (16:29 -0800)]
mm: vmscan: check for fatal signals iff the process was throttled

Commit 5515061d22f0 ("mm: throttle direct reclaimers if PF_MEMALLOC
reserves are low and swap is backed by network storage") introduced a
check for fatal signals after a process gets throttled for network
storage.  The intention was that if a process was throttled and got
killed that it should not trigger the OOM killer.  As pointed out by
Minchan Kim and David Rientjes, this check is in the wrong place and too
broad.  If a system is in am OOM situation and a process is exiting, it
can loop in __alloc_pages_slowpath() and calling direct reclaim in a
loop.  As the fatal signal is pending it returns 1 as if it is making
forward progress and can effectively deadlock.

This patch moves the fatal_signal_pending() check after throttling to
throttle_direct_reclaim() where it belongs.  If the process is killed
while throttled, it will return immediately without direct reclaim
except now it will have TIF_MEMDIE set and will use the PFMEMALLOC
reserves.

Minchan pointed out that it may be better to direct reclaim before
returning to avoid using the reserves because there may be pages that
can easily reclaim that would avoid using the reserves.  However, we do
no such targetted reclaim and there is no guarantee that suitable pages
are available.  As it is expected that this throttling happens when
swap-over-NFS is used there is a possibility that the process will
instead swap which may allocate network buffers from the PFMEMALLOC
reserves.  Hence, in the swap-over-nfs case where a process can be
throtted and be killed it can use the reserves to exit or it can
potentially use reserves to swap a few pages and then exit.  This patch
takes the option of using the reserves if necessary to allow the process
exit quickly.

If this patch passes review it should be considered a -stable candidate
for 3.6.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Sonny Rao <sonnyrao@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoRevert "mm: remove __GFP_NO_KSWAPD"
Mel Gorman [Tue, 27 Nov 2012 00:29:45 +0000 (16:29 -0800)]
Revert "mm: remove __GFP_NO_KSWAPD"

With "mm: vmscan: scale number of pages reclaimed by reclaim/compaction
based on failures" reverted, Zdenek Kabelac reported the following

  Hmm,  so it's just took longer to hit the problem and observe
  kswapd0 spinning on my CPU again - it's not as endless like before -
  but still it easily eats minutes - it helps to turn off  Firefox
  or TB  (memory hungry apps) so kswapd0 stops soon - and restart
  those apps again.  (And I still have like >1GB of cached memory)

  kswapd0         R  running task        0    30      2 0x00000000
  Call Trace:
    preempt_schedule+0x42/0x60
    _raw_spin_unlock+0x55/0x60
    put_super+0x31/0x40
    drop_super+0x22/0x30
    prune_super+0x149/0x1b0
    shrink_slab+0xba/0x510

The sysrq+m indicates the system has no swap so it'll never reclaim
anonymous pages as part of reclaim/compaction.  That is one part of the
problem but not the root cause as file-backed pages could also be
reclaimed.

The likely underlying problem is that kswapd is woken up or kept awake
for each THP allocation request in the page allocator slow path.

If compaction fails for the requesting process then compaction will be
deferred for a time and direct reclaim is avoided.  However, if there
are a storm of THP requests that are simply rejected, it will still be
the the case that kswapd is awake for a prolonged period of time as
pgdat->kswapd_max_order is updated each time.  This is noticed by the
main kswapd() loop and it will not call kswapd_try_to_sleep().  Instead
it will loopp, shrinking a small number of pages and calling
shrink_slab() on each iteration.

The temptation is to supply a patch that checks if kswapd was woken for
THP and if so ignore pgdat->kswapd_max_order but it'll be a hack and not
backed up by proper testing.  As 3.7 is very close to release and this
is not a bug we should release with, a safer path is to revert "mm:
remove __GFP_NO_KSWAPD" for now and revisit it with the view to ironing
out the balance_pgdat() logic in general.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoproc: check vma->vm_file before dereferencing
Stanislav Kinsbursky [Tue, 27 Nov 2012 00:29:42 +0000 (16:29 -0800)]
proc: check vma->vm_file before dereferencing

Commit 7b540d0646ce ("proc_map_files_readdir(): don't bother with
grabbing files") switched proc_map_files_readdir() to use @f_mode
directly instead of grabbing @file reference, but same time the test for
@vm_file presence was lost leading to nil dereference.  The patch brings
the test back.

The all proc_map_files feature is CONFIG_CHECKPOINT_RESTORE wrapped
(which is set to 'n' by default) so the bug doesn't affect regular
kernels.

The regression is 3.7-rc1 only as far as I can tell.

[gorcunov@openvz.org: provided changelog]
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoUAPI: strip the _UAPI prefix from header guards during header installation
David Howells [Tue, 27 Nov 2012 00:29:39 +0000 (16:29 -0800)]
UAPI: strip the _UAPI prefix from header guards during header installation

Strip the _UAPI prefix from header guards during header installation so
that any userspace dependencies aren't affected.  glibc, for example,
checks for linux/types.h, linux/kernel.h, linux/compiler.h and
linux/list.h by their guards - though the last two aren't actually
exported.

  libtool: compile:  gcc -std=gnu99 -DHAVE_CONFIG_H -I. -Wall -Werror -Wformat -Wformat-security -D_FORTIFY_SOURCE=2 -fno-delete-null-pointer-checks -fstack-protector -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m32 -march=i686 -mtune=atom -fasynchronous-unwind-tables -c child.c  -fPIC -DPIC -o .libs/child.o
  In file included from cli.c:20:0:
  common.h:152:8: error: redefinition of 'struct sysinfo'
  In file included from /usr/include/linux/kernel.h:4:0,
    from /usr/include/linux/sysctl.h:25,
    from /usr/include/sys/sysctl.h:43,
    from common.h:50,
    from cli.c:20:
  /usr/include/linux/sysinfo.h:7:8: note: originally defined here

Reported-by: Tomasz Torcz <tomek@pipebreaker.pl>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agoinclude/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Tushar Behera [Tue, 27 Nov 2012 00:29:38 +0000 (16:29 -0800)]
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID

Commit baf05aa9271b ("bug: introduce BUILD_BUG_ON_INVALID() macro")
introduces this macro only when _CHECKER_ is not defined.  Define a
silent macro in the else condition to fix following sparse warning:

  mm/filemap.c:395:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
  mm/filemap.c:396:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
  mm/filemap.c:397:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
  include/linux/mm.h:419:9: error: undefined identifier 'BUILD_BUG_ON_INVALID'
  include/linux/mm.h:419:9: error: not a function <noident>

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
11 years agonet: ipmr: limit MRT_TABLE identifiers
Eric Dumazet [Sun, 25 Nov 2012 09:44:29 +0000 (09:44 +0000)]
net: ipmr: limit MRT_TABLE identifiers

Name of pimreg devices are built from following format :

char name[IFNAMSIZ]; // IFNAMSIZ == 16

sprintf(name, "pimreg%u", mrt->id);

We must therefore limit mrt->id to 9 decimal digits
or risk a buffer overflow and a crash.

Restrict table identifiers in [0 ... 999999999] interval.

Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoip6mr: Add sizeof verification to MRT6_ASSERT and MT6_PIM
Joe Perches [Sun, 25 Nov 2012 18:26:34 +0000 (18:26 +0000)]
ip6mr: Add sizeof verification to MRT6_ASSERT and MT6_PIM

Verify the length of the user-space arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoipv4: avoid passing NULL to inet_putpeer() in icmpv4_xrlim_allow()
Neal Cardwell [Sat, 24 Nov 2012 18:54:37 +0000 (18:54 +0000)]
ipv4: avoid passing NULL to inet_putpeer() in icmpv4_xrlim_allow()

inet_getpeer_v4() can return NULL under OOM conditions, and while
inet_peer_xrlim_allow() is OK with a NULL peer, inet_putpeer() will
crash.

This code path now uses the same idiom as the others from:
1d861aa4b3fb08822055345f480850205ffe6170 ("inet: Minimize use of
cached route inetpeer.").

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosockopt: Change getsockopt() of SO_BINDTODEVICE to return an interface name
Brian Haley [Mon, 26 Nov 2012 05:21:08 +0000 (05:21 +0000)]
sockopt: Change getsockopt() of SO_BINDTODEVICE to return an interface name

Instead of having the getsockopt() of SO_BINDTODEVICE return an index, which
will then require another call like if_indextoname() to get the actual interface
name, have it return the name directly.

This also matches the existing man page description on socket(7) which mentions
the argument being an interface name.

If the value has not been set, zero is returned and optlen will be set to zero
to indicate there is no interface name present.

Added a seqlock to protect this code path, and dev_ifname(), from someone
changing the device name via dev_change_name().

v2: Added seqlock protection while copying device name.

v3: Fixed word wrap in patch.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocpts: add missing kconfig dependency
Richard Cochran [Mon, 26 Nov 2012 02:07:18 +0000 (02:07 +0000)]
cpts: add missing kconfig dependency

The Common Platform Time Sync function of the CPSW does not depend the
CPSW configuration option as it should. This patch fixes the issue by
adding the dependency.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoptp: reduce stack usage when measuring the system time offset
Richard Cochran [Mon, 26 Nov 2012 01:44:35 +0000 (01:44 +0000)]
ptp: reduce stack usage when measuring the system time offset

This patch removes the large buffer from the stack of the system
offset ioctl and replaces it with a kmalloced buffer.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoptp: reduce stack usage when reading external time stamps
Richard Cochran [Mon, 26 Nov 2012 01:44:34 +0000 (01:44 +0000)]
ptp: reduce stack usage when reading external time stamps

This patch removes the large buffer from the stack of the read file
operation and replaces it with a kmalloced buffer.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agostmmac: update the driver version to Nov_2012
Giuseppe CAVALLARO [Sun, 25 Nov 2012 23:10:46 +0000 (23:10 +0000)]
stmmac: update the driver version to Nov_2012

Many new feauture have been introduced in the driver:
ethtool coalesce options, Rx HW watchdog... so this patch updates the
driver's version.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agostmmac: update the doc with new IRQ mitigation
Giuseppe CAVALLARO [Sun, 25 Nov 2012 23:10:45 +0000 (23:10 +0000)]
stmmac: update the doc with new IRQ mitigation

This patch updates the stmmac.txt adding some information
about the new rx/tx mitigation schema adopted in the driver.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agostmmac: get/set coalesce parameters via ethtool
Giuseppe CAVALLARO [Sun, 25 Nov 2012 23:10:44 +0000 (23:10 +0000)]
stmmac: get/set coalesce parameters via ethtool

This patch is to get/set the tx/rx coalesce parameters
via ethtool interface.

Tests have been done on several platform with different GMAC chips w/o and w/
RX watchdog feature.

V2: reject coalesce settings that are not supported.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>