Frank Praznik [Mon, 14 Apr 2014 14:11:36 +0000 (10:11 -0400)]
HID: sony: Add blink support to the Sixaxis and DualShock 4 LEDs
Add support for setting the blink rate of the LEDs. The Sixaxis allows control
over each individual LED, but the Dualshock 4 only has one global control for
controlling the hardware blink rate so individual colors will fall back to
software timers.
Setting the brightness cancels the blinking as per the LED class specifications.
The Sixaxis and Dualshock 4 controllers accept delays in decisecond increments
from 0 to 255 (2550 milliseconds).
The value at index 1 of the DualShock 4 USB output report must be 0xFF or the
light bar won't blink.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Frank Praznik [Mon, 14 Apr 2014 14:11:35 +0000 (10:11 -0400)]
HID: sony: Initialize the controller LEDs with a device ID value
Add an IDA id allocator to assign unique, sequential device ids to Sixaxis and
DualShock 4 controllers.
Use the device ID to initialize the Sixaxis and DualShock 4 controller LEDs to
default values. The number or color of the controller is set relative to other
connected Sony controllers.
Set the LED class brightness values to the initial values and add the new led to
the array before calling led_classdev_register so that the correct brightness
value shows up in the LED sysfs entry.
Use explicit module init and exit functions since the IDA allocator must be
manually destroyed when the module is unloaded.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Frank Praznik [Mon, 14 Apr 2014 14:11:33 +0000 (10:11 -0400)]
HID: sony: Convert startup and shutdown functions to use a uniform parameter type
Convert all of the local initialization and shutdown functions to take a
parameter type of struct sony_sc* instead of using a mix of struct sony_sc* and
struct hid_device*.
Allows for the removal of some calls to hid_get_drvdata().
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for merge window mismerge in hid-sony, from Frank Praznik
- fix for Surface Type/Touch Cover 2 device, from Benjamin Tissoires
- quirk for ThinkPad Helix sensor hub from Stephen Chandler Paul
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: do not scan constant input report
Revert "HID: microsoft: Add ID's for Surface Type/Touch Cover 2"
HID: sensor-hub: add sensor hub quirk for ThinkPad Helix
HID: sony: Fix cancel_work_sync mismerge
Merge tag 'sound-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a copule of HD-audio device/codec-specific quirks, and a trivial
replacement of udelay() with mdelay() in the old es18xx driver code.
All should be safe to apply"
* tag 'sound-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add headset Mic support for Dell machine
ALSA: hda - add headset mic detect quirk for a Dell laptop
ALSA: es18xx driver should use udelay error
ALSA: hda/realtek - Add support of ALC288 codec
Merge tag 'dt-fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- fix error handling in of_update_property
- fix section mismatch warnings in __reserved_mem_check_root
- add empty of_find_node_by_path for !OF builds
- add various missing binding documentation
* tag 'dt-fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: add empty of_find_node_by_path() for !OF
of: Clean up of_update_property
DT: add vendor prefix for EBV Elektronik
of: Fix the section mismatch warnings.
of: Add vendor prefix for Digi International Inc.
DT: I2C: Add trivial bindings used by kirkwood boards
DT: Vendor: Add prefixes used by Kirkwood devices
DT: bindings: add missing Marvell Kirkwood SoC documentation
dt-bindings: add vendor-prefix for Newhaven Display
of: add vendor prefix for I2SE GmbH
of: add vendor prefix for ISEE 2007 S.L.
Merge tag 'xfs-for-linus-3.15-rc2' of git://oss.sgi.com/xfs/xfs
Pull xfs bug fixes from Dave Chinner:
"The fixes are for data corruption issues, memory corruption and
regressions for changes merged in -rc1.
Data corruption fixes:
- fix a bunch of delayed allocation state mismatches
- fix collapse/zero range bugs
- fix a direct IO block mapping bug @ EOF
Other fixes:
- fix a use after free on metadata IO error
- fix a use after free on IO error during unmount
- fix an incorrect error sign on direct IO write errors
- add missing O_TMPFILE inode security context initialisation"
* tag 'xfs-for-linus-3.15-rc2' of git://oss.sgi.com/xfs/xfs:
xfs: fix tmpfile/selinux deadlock and initialize security
xfs: fix buffer use after free on IO error
xfs: wrong error sign conversion during failed DIO writes
xfs: unmount does not wait for shutdown during unmount
xfs: collapse range is delalloc challenged
xfs: don't map ranges that span EOF for direct IO
xfs: zeroing space needs to punch delalloc blocks
xfs: xfs_vm_write_end truncates too much on failure
xfs: write failure beyond EOF truncates too much data
xfs: kill buffers over failed write ranges properly
Merge tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains two fixes.
The first is to remove a duplication of creating debugfs files that
already exist and causes an error report to be printed due to the
failure of the second creation.
The second is a memory leak fix that was introduced in 3.14"
* tag 'trace-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobes: Fix uprobe_cpu_buffer memory leak
tracing: Do not try to recreated toplevel set_ftrace_* files
Alexander Shiyan [Wed, 16 Apr 2014 06:49:20 +0000 (10:49 +0400)]
of: add empty of_find_node_by_path() for !OF
Add an empty version of of_find_node_by_path().
This fixes following build error for asoc tree:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1471:2: error: implicit declaration of function 'of_find_node_by_path' [-Werror=implicit-function-declaration]
sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Rob Herring <robh@kernel.org>
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Viresh unearthed the following three hickups in the timer/timekeeping
code:
- Negated check for the result of a clock event selection
- A missing early exit in the jiffies update path which causes
update_wall_time to be called for nothing causing lock contention
and wasted cycles in the timer interrupt
- Checking a variable in the NOHZ code enable code for true which can
only be set by that very code after the check succeeds. That
results in a rock solid runtime disablement of that feature"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz()
tick-sched: Don't call update_wall_time() when delta is lesser than tick_period
tick-common: Fix wrong check in tick_check_replacement()
Merge branch 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"There are two major changes in this patchset:
The major fix is that the epoll_pwait() syscall for 32bit userspace
was not using the compat wrapper on a 64bit kernel.
Secondly we changed the value of SHMLBA from 4MB to PAGE_SIZE to
reflect that we can actually mmap to any multiple of PAGE_SIZE. The
only thing which needs care is that shared mmaps need to be mapped at
the same offset inside the 4MB cache window"
* 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix epoll_pwait syscall on compat kernel
parisc: change value of SHMLBA from 0x00400000 to PAGE_SIZE
parisc: Replace __get_cpu_var uses for address calculation
Merge ipmi fixes from Corey Minyard:
"Things collected since last kernel release.
Some of these are pretty important. The first three are bug fixes.
The next two are to hopefully make everyone happy about allowing
ACPI to be on all the time and not have IPMI have an effect on the
system when not in use. The last is a little cleanup"
* emailed patches from Corey Minyard <cminyard@mvista.com>:
ipmi: boolify some things
ipmi: Turn off all activity on an idle ipmi interface
ipmi: Turn off default probing of interfaces
ipmi: Reset the KCS timeout when starting error recovery
ipmi: Fix a race restarting the timer
Char: ipmi_bt_sm, fix infinite loop
ipmi: Turn off all activity on an idle ipmi interface
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
The default probing can cause problems with some system, slow booting,
extra CPU usages, etc. Turn it off by default and give a config option
to enable it.
Bodo Stroesser [Mon, 14 Apr 2014 14:46:51 +0000 (09:46 -0500)]
ipmi: Fix a race restarting the timer
With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time. The thread will not start the timer in that
instance, resulting in the timer not running.
Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer. 'Timer is not running' means that the timer is not
pending and smi_timeout() is not running. So we need a flag to detect
this correctly.
Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Merge tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from David Vrabel:
"Xen regression and bug fixes for 3.15-rc1:
- fix completely broken 32-bit PV guests caused by x86 refactoring
32-bit thread_info.
- only enable ticketlock slow path on Xen (not bare metal)
- fix two bugs with PV guests not shutting down when requested
- fix a minor memory leak in xen-pciback error path"
* tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/manage: Poweroff forcefully if user-space is not yet up.
xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
xen/spinlock: Don't enable them unconditionally.
xen-pciback: silence an unwanted debug printk
xen: fix memory leak in __xen_pcibk_add_pci_dev()
x86/xen: Fix 32-bit PV guests's usage of kernel_stack
Merge tag 'fbdev-reorder-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev renaming patches from Tomi Valkeinen:
"Reorder drivers/video/ directory so that all fbdev drivers are now
located in drivers/video/fbdev/ and the fbdev framework core files are
located in drivers/video/fbdev/core/
The drivers/video/Kconfig is modified so that the DRM and the fbdev
menu options are in separate submenus, instead of both being mixed in
the same 'Graphics support' menu level"
* tag 'fbdev-reorder-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: Kconfig: move drm and fb into separate menus
fbdev: move fbdev core files to separate directory
video: move fbdev to drivers/video/fbdev
Shaohua Li [Tue, 15 Apr 2014 01:12:54 +0000 (09:12 +0800)]
raid5: fix a race of stripe count check
I hit another BUG_ON with e240c1839d11152b0355442. In __get_priority_stripe(),
stripe count equals to 0 initially. Between atomic_inc and BUG_ON,
get_active_stripe() finds the stripe. So the stripe count isn't 1 any more.
V2: keeps the BUG_ON suggested by Neil.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: NeilBrown <neilb@suse.de>
Tomi Valkeinen [Thu, 13 Feb 2014 14:32:13 +0000 (16:32 +0200)]
video: Kconfig: move drm and fb into separate menus
At the moment the "Device Drivers / Graphics support" kernel config page
looks rather messy, with DRM and fbdev driver selections on the same
page, some on the top level Graphics support page, some under their
respective subsystems.
If I'm not mistaken, this is caused by the drivers depending on other
things than DRM or FB, which causes Kconfig to arrange the options in
not-so-neat manner.
Both DRM and FB have a main menuconfig option for the whole DRM or FB
subsystem. Optimally, this would be enough to arrange all DRM and FB
options under the respective subsystem, but for whatever reason this
doesn't work reliably.
This patch adds an explicit submenu for DRM and FB, making it much
clearer which options are related to FB, and which to DRM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tomi Valkeinen [Thu, 13 Feb 2014 14:24:55 +0000 (16:24 +0200)]
fbdev: move fbdev core files to separate directory
Instead of having fbdev framework core files at the root fbdev
directory, mixed with random fbdev device drivers, move the fbdev core
files to a separate core directory. This makes it much clearer which of
the files are actually part of the fbdev framework, and which are part
of device drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Rob Clark <robdclark@gmail.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tomi Valkeinen [Thu, 13 Feb 2014 13:31:38 +0000 (15:31 +0200)]
video: move fbdev to drivers/video/fbdev
The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.
Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.
No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Rob Clark <robdclark@gmail.com> Acked-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plus the wire-up of the renameat2() system call on i386"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove the PCI reboot method from the default chain
x86/build: Supress "Nothing to be done for ..." messages
x86/gpu: Fix sign extension issue in Intel graphics stolen memory quirks
x86/platform: Fix "make O=dir kvmconfig"
i386: Wire up the renameat2() syscall
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Tooling fixes, plus a simple hardware-enablement patch for the Intel
RAPL PMU (energy use measurement) on Haswell CPUs, which I hope is
still fine at this stage"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Instead of redirecting flex output, use -o
perf tools: Fix double free in perf test 21 (code-reading.c)
perf stat: Initialize statistics correctly
perf bench: Set more defaults in the 'numa' suite
perf bench: Fix segfault at the end of an 'all' execution
perf bench: Update manpage to mention numa and futex
perf probe: Use dwarf_getcfi_elf() instead of dwarf_getcfi()
perf probe: Fix to handle errors in line_range searching
perf probe: Fix --line option behavior
perf tools: Pick up libdw without explicit LIBDW_DIR
MAINTAINERS: Change e-mail to kernel.org one
perf callchains: Disable unwind libraries when libelf isn't found
tools lib traceevent: Do not call warning() directly
tools lib traceevent: Print event name when show warning if possible
perf top: Fix documentation of invalid -s option
perf/x86: Enable DRAM RAPL support on Intel Haswell
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"liblockdep fixes and mutex debugging fixes"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/mutex: Fix debug_mutexes
tools/liblockdep: Add proper versioning to the shared obj
tools/liblockdep: Ignore asmlinkage and visible
tracing: Do not try to recreated toplevel set_ftrace_* files
With the restructing of the function tracer working with instances, the
"top level" buffer is a bit special, as the function tracing is mapped
to the same set of filters. This is done by using a "global_ops" descriptor
and having the "set_ftrace_filter" and "set_ftrace_notrace" map to it.
When an instance is created, it creates the same files but its for the
local instance and not the global_ops.
The issues is that the local instance creation shares some code with
the global instance one and we end up trying to create th top level
"set_ftrace_*" files twice, and on boot up, we get an error like this:
Could not create debugfs 'set_ftrace_filter' entry
Could not create debugfs 'set_ftrace_notrace' entry
The reason they failed to be created was because they were created
twice, and the second time gives this error as you can not create the
same file twice.
Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge tag 'fbdev-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fix build errors for bf54x-lq043fb and imxfb
- fbcon fix for da8xx-fb
- omapdss fixes for hdmi audio, irq handling and fclk calculation
* tag 'fbdev-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: bf54x-lq043fb: fix build error
OMAPDSS: Change struct reg_field to dispc_reg_field
OMAPDSS: Take pixelclock unit change into account in hdmi_compute_acr()
OMAPDSS: fix shared irq handlers
video: imxfb: Select LCD_CLASS_DEVICE unconditionally
OMAPDSS: fix rounding when calculating fclk rate
video: da8xx-fb: Fix casting of info->pseudo_palette
Merge tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol fixes from Linus Walleij:
"A first set of pin control fixes for the v3.15 series:
- Fix a couple of barnsjukdomar on the Rockchip driver.
- Remove an idiotic debug print I happened to leave behind in the
Nomadik driver.
- Fixup the Qualcomm MSM interrupt handling code for the TLMM v2.
- Three patches renaming the Broadcom Capri driver to BCM28155. This
has been falling between the chairs for some time due to some
cross-tree synchronization misunderstandings, now I'm fed up with
this and just rename it in this -rc1 phase"
* tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix typo in bindings documentation
Update bcm_defconfig with new pinctrl CONFIG
pinctrl: Rename Broadcom Capri pinctrl driver
pinctrl: msm: Correct interrupt code for TLMM v2
pinctrl: nomadik: delete stray debug print
pinctrl: rockchip: handle first half of rk3188-bank0 correctly
pinctrl: rockchip: add return value to rockchip_set_mux
pinctrl: rockchip: fix offset of mux registers for rk3188
Brian Foster [Wed, 16 Apr 2014 22:15:30 +0000 (08:15 +1000)]
xfs: fix tmpfile/selinux deadlock and initialize security
xfstests generic/004 reproduces an ilock deadlock using the tmpfile
interface when selinux is enabled. This occurs because
xfs_create_tmpfile() takes the ilock and then calls d_tmpfile(). The
latter eventually calls into xfs_xattr_get() which attempts to get the
lock again. E.g.:
xfs_vn_tmpfile() also fails to initialize security on the newly created
inode.
Pull the d_tmpfile() call up into xfs_vn_tmpfile() after the transaction
has been committed and the inode unlocked. Also, initialize security on
the inode based on the parent directory provided via the tmpfile call.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
At issue is the fact that if IO fails in xfs_buf_iorequest,
we'll queue completion unconditionally, and then call
xfs_buf_rele; but if IO failed, there are no IOs remaining,
and xfs_buf_rele will free the bp while work is still queued.
Fix this by not scheduling completion if the buffer has
an error on it; run it immediately. The rest is only comment
changes.
Thanks to dchinner for spotting the root cause.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 16 Apr 2014 22:15:27 +0000 (08:15 +1000)]
xfs: wrong error sign conversion during failed DIO writes
We negate the error value being returned from a generic function
incorrectly. The code path that it is running in returned negative
errors, so there is no need to negate it to get the correct error
signs here.
This was uncovered by generic/019.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 16 Apr 2014 22:15:26 +0000 (08:15 +1000)]
xfs: unmount does not wait for shutdown during unmount
And interesting situation can occur if a log IO error occurs during
the unmount of a filesystem. The cases reported have the same
signature - the update of the superblock counters fails due to a log
write IO error:
XFS (dm-16): xfs_do_force_shutdown(0x2) called from line 1170 of file fs/xfs/xfs_log.c. Return address = 0xffffffffa08a44a1
XFS (dm-16): Log I/O Error Detected. Shutting down filesystem
XFS (dm-16): Unable to update superblock counters. Freespace may not be correct on next mount.
XFS (dm-16): xfs_log_force: error 5 returned.
XFS (¿-¿¿¿): Please umount the filesystem and rectify the problem(s)
It can be seen that the last line of output contains a corrupt
device name - this is because the log and xfs_mount structures have
already been freed by the time this message is printed. A kernel
oops closely follows.
The issue is that the shutdown is occurring in a separate IO
completion thread to the unmount. Once the shutdown processing has
started and all the iclogs are marked with XLOG_STATE_IOERROR, the
log shutdown code wakes anyone waiting on a log force so they can
process the shutdown error. This wakes up the unmount code that
is doing a synchronous transaction to update the superblock
counters.
The unmount path now sees all the iclogs are marked with
XLOG_STATE_IOERROR and so never waits on them again, knowing that if
it does, there will not be a wakeup trigger for it and we will hang
the unmount if we do. Hence the unmount runs through all the
remaining code and frees all the filesystem structures while the
xlog_iodone() is still processing the shutdown. When the log
shutdown processing completes, xfs_do_force_shutdown() emits the
"Please umount the filesystem and rectify the problem(s)" message,
and xlog_iodone() then aborts all the objects attached to the iclog.
An iclog that has already been freed....
The real issue here is that there is no serialisation point between
the log IO and the unmount. We have serialisations points for log
writes, log forces, reservations, etc, but we don't actually have
any code that wakes for log IO to fully complete. We do that for all
other types of object, so why not iclogbufs?
Well, it turns out that we can easily do this. We've got xfs_buf
handles, and that's what everyone else uses for IO serialisation.
i.e. bp->b_sema. So, lets hold iclogbufs locked over IO, and only
release the lock in xlog_iodone() when we are finished with the
buffer. That way before we tear down the iclog, we can lock and
unlock the buffer to ensure IO completion has finished completely
before we tear it down.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Mike Snitzer <snitzer@redhat.com> Tested-by: Bob Mastors <bob.mastors@solidfire.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 16 Apr 2014 22:15:25 +0000 (08:15 +1000)]
xfs: collapse range is delalloc challenged
FSX has been detecting data corruption after to collapse range
calls. The key observation is that the offset of the last extent in
the file was not being shifted, and hence when the file size was
adjusted it was truncating away data because the extents handled
been correctly shifted.
Tracing indicated that before the collapse, the extent list looked
like:
....
ino 0x5788 state idx 6 offset 26 block 195904 count 10 flag 0
ino 0x5788 state idx 7 offset 39 block 195917 count 35 flag 0
ino 0x5788 state idx 8 offset 86 block 195964 count 32 flag 0
and after the shift of 2 blocks:
ino 0x5788 state idx 6 offset 24 block 195904 count 10 flag 0
ino 0x5788 state idx 7 offset 37 block 195917 count 35 flag 0
ino 0x5788 state idx 8 offset 86 block 195964 count 32 flag 0
Note that the last extent did not change offset. After the changing
of the file size:
ino 0x5788 state idx 6 offset 24 block 195904 count 10 flag 0
ino 0x5788 state idx 7 offset 37 block 195917 count 35 flag 0
ino 0x5788 state idx 8 offset 86 block 195964 count 30 flag 0
You can see that the last extent had it's length truncated,
indicating that we've lost data.
The reason for this is that the xfs_bmap_shift_extents() loop uses
XFS_IFORK_NEXTENTS() to determine how many extents are in the inode.
This, unfortunately, doesn't take into account delayed allocation
extents - it's a count of physically allocated extents - and hence
when the file being collapsed has a delalloc extent like this one
does prior to the range being collapsed:
....
ino 0x5788 state idx 4 offset 11 block 4503599627239429 count 1 flag 0
....
it gets the count wrong and terminates the shift loop early.
Fix it by using the in-memory extent array size that includes
delayed allocation extents to determine the number of extents on the
inode.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
Dave Chinner [Wed, 16 Apr 2014 22:15:19 +0000 (08:15 +1000)]
xfs: don't map ranges that span EOF for direct IO
Al Viro tracked down the problem that has caused generic/263 to fail
on XFS since the test was introduced. If is caused by
xfs_get_blocks() mapping a single extent that spans EOF without
marking it as buffer-new() so that the direct IO code does not zero
the tail of the block at the new EOF. This is a long standing bug
that has been around for many, many years.
Because xfs_get_blocks() starts the map before EOF, it can't set
buffer_new(), because that causes he direct IO code to also zero
unaligned sectors at the head of the IO. This would overwrite valid
data with zeros, and hence we cannot validly return a single extent
that spans EOF to direct IO.
Fix this by detecting a mapping that spans EOF and truncate it down
to EOF. This results in the the direct IO code doing the right thing
for unaligned data blocks before EOF, and then returning to get
another mapping for the region beyond EOF which XFS treats correctly
by setting buffer_new() on it. This makes direct Io behave correctly
w.r.t. tail block zeroing beyond EOF, and fsx is happy about that.
Again, thanks to Al Viro for finding what I couldn't.
[ dchinner: Fix for __divdi3 build error:
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com>
]
Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"An update to the oops output with additional information about the
crash. The renameat2 system call is enabled. Two patches in regard
to the PTR_ERR_OR_ZERO cleanup. And a bunch of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/sclp_cmd: replace PTR_RET with PTR_ERR_OR_ZERO
s390/sclp: replace PTR_RET with PTR_ERR_OR_ZERO
s390/sclp_vt220: Fix kernel panic due to early terminal input
s390/compat: fix typo
s390/uaccess: fix possible register corruption in strnlen_user_srst()
s390: add 31 bit warning message
s390: wire up sys_renameat2
s390: show_registers() should not map user space addresses to kernel symbols
s390/mm: print control registers and page table walk on crash
s390/smp: fix smp_stop_cpu() for !CONFIG_SMP
s390: fix control register update
Merge tag 'please-pull-ia64-erratum' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull itanium erratum fix from Tony Luck:
"Small workaround for a rare, but annoying, erratum #237"
* tag 'please-pull-ia64-erratum' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Change default PSR.ac from '1' to '0' (Fix erratum #237)
=========================================================================
237. Under a complex set of conditions, store to load forwarding for a
sub 8-byte load may complete incorrectly
Problem: A load instruction may complete incorrectly when a code sequence
using 4-byte or smaller load and store operations to the same address
is executed in combination with specific timing of all the following
concurrent conditions: store to load forwarding, alignment checking
enabled, a mis-predicted branch, and complex cache utilization activity.
Implication: The affected sub 8-byte instruction may complete
incorrectly resulting in unpredictable system behavior. There is an
extremely low probability of exposure due to the significant number of
complex microarchitectural concurrent conditions required to encounter
the erratum.
Workaround: Set PSR.ac = 0 to completely avoid the erratum. Disabling
Hyper-Threading will significantly reduce exposure to the conditions
that contribute to encountering the erratum.
Status: See the Summary Table of Changes for the affected steppings.
=========================================================================
[Table of changes essentially lists all models from McKinley to Tukwila]
The PSR.ac bit controls whether the processor will always generate
an unaligned reference trap (0x5a00) for a misaligned data access
(when PSR.ac=1) or if it will let the access succeed when running
on a cpu that implements logic to handle some unaligned accesses.
Way back in 2008 in commit b704882e70d87d7f56db5ff17e2253f3fa90e4f3
[IA64] Rationalize kernel mode alignment checking
we made the decision to always enable strict checking. We were
already doing so in trap/interrupt context because the common
preamble code set this bit - but the rest of supervisor code
(and by inheritance user code) ran with PSR.ac=0.
We now reverse that decision and set PSR.ac=0 everywhere in the
kernel (also inherited by user processes). This will avoid the
erratum using the method described in the Itanium specification
update. Net effect for users is that the processor will handle
unaligned access when it can (typically with a tiny performance
bubble in the pipeline ... but much less invasive than taking a
trap and having the OS perform the access).
x86: Remove the PCI reboot method from the default chain
Steve reported a reboot hang and bisected it back to this commit:
a4f1987e4c54 x86, reboot: Add EFI and CF9 reboot methods into the default list
He heroically tested all reboot methods and found the following:
reboot=t # triple fault ok
reboot=k # keyboard ctrl FAIL
reboot=b # BIOS ok
reboot=a # ACPI FAIL
reboot=e # EFI FAIL [system has no EFI]
reboot=p # PCI 0xcf9 FAIL
And I think it's pretty obvious that we should only try PCI 0xcf9 as a
last resort - if at all.
The other observation is that (on this box) we should never try
the PCI reboot method, but close with either the 'triple fault'
or the 'BIOS' (terminal!) reboot methods.
Thirdly, CF9_COND is a total misnomer - it should be something like
CF9_SAFE or CF9_CAREFUL, and 'CF9' should be 'CF9_FORCE' ...
So this patch fixes the worst problems:
- it orders the actual reboot logic to follow the reboot ordering
pattern - it was in a pretty random order before for no good
reason.
- it fixes the CF9 misnomers and uses BOOT_CF9_FORCE and
BOOT_CF9_SAFE flags to make the code more obvious.
- it tries the BIOS reboot method before the PCI reboot method.
(Since 'BIOS' is a terminal reboot method resulting in a hang
if it does not work, this is essentially equivalent to removing
the PCI reboot method from the default reboot chain.)
- just for the miraculous possibility of terminal (resulting
in hang) reboot methods of triple fault or BIOS returning
without having done their job, there's an ordering between
them as well.
Reported-and-bisected-and-tested-by: Steven Rostedt <rostedt@goodmis.org> Cc: Li Aubrey <aubrey.li@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Link: http://lkml.kernel.org/r/20140404064120.GB11877@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hui Wang [Wed, 16 Apr 2014 02:09:08 +0000 (10:09 +0800)]
ALSA: hda - add headset mic detect quirk for a Dell laptop
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x1028067f), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581 Cc: David Henningsson <david.henningsson@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
1) Fix BPF filter validation of netlink attribute accesses, from
Mathias Kruase.
2) Netfilter conntrack generation seqcount not initialized properly,
from Andrey Vagin.
3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
from Patrick McHardy.
4) Properly limit MTU over ipv6, from Eric Dumazet.
5) Fix seccomp system call argument population on 32-bit, from Daniel
Borkmann.
6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
skb->mac_len needs to be used. From Vlad Yasevich.
7) We have several cases of using socket based communications to
implement a tunnel. For example, some tunnels are encapsulations
over UDP so we use an internal kernel UDP socket to do the
transmits.
These tunnels should behave just like other software devices and
pass the packets on down to the next layer.
Most importantly we want the top-level socket (eg TCP) that created
the traffic to be charged for the SKB memory.
However, once you get into the IP output path, we have code that
assumed that whatever was attached to skb->sk is an IP socket.
To keep the top-level socket being charged for the SKB memory,
whilst satisfying the needs of the IP output path, we now pass in an
explicit 'sk' argument.
From Eric Dumazet.
8) ping_init_sock() leaks group info, from Xiaoming Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
cxgb4: use the correct max size for firmware flash
qlcnic: Fix MSI-X initialization code
ip6_gre: don't allow to remove the fb_tunnel_dev
ipv4: add a sock pointer to dst->output() path.
ipv4: add a sock pointer to ip_queue_xmit()
driver/net: cosa driver uses udelay incorrectly
at86rf230: fix __at86rf230_read_subreg function
at86rf230: remove check if AVDD settled
net: cadence: Add architecture dependencies
net: Start with correct mac_len in skb_network_protocol
Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
qlcnic: Fix PVID configuration on eSwitch port.
qlcnic: Fix max ring count calculation
qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
...
Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com> Cc: Dept-HSGLinuxNICDev@qlogic.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Mon, 14 Apr 2014 15:11:38 +0000 (17:11 +0200)]
ip6_gre: don't allow to remove the fb_tunnel_dev
It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.
Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).
Introduced by commit c12b395a4664 ("gre: Support GRE over IPv6").
CC: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tick-sched: Check tick_nohz_enabled in tick_nohz_switch_to_nohz()
Since commit d689fe222 (NOHZ: Check for nohz active instead of nohz
enabled) the tick_nohz_switch_to_nohz() function returns because it
checks for the tick_nohz_active flag. This can't be set, because the
function itself sets it.
tick-sched: Don't call update_wall_time() when delta is lesser than tick_period
In tick_do_update_jiffies64() we are processing ticks only if delta is
greater than tick_period. This is what we are supposed to do here and
it broke a bit with this patch:
commit 47a1b796 (tick/timekeeping: Call update_wall_time outside the
jiffies lock)
With above patch, we might end up calling update_wall_time() even if
delta is found to be smaller that tick_period. Fix this by returning
when the delta is less than tick period.
[ tglx: Made it a 3 liner and massaged changelog ]
Eric Dumazet [Tue, 15 Apr 2014 17:47:15 +0000 (13:47 -0400)]
ipv4: add a sock pointer to dst->output() path.
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d55 ("vxlan: keep original skb ownership") Reported-by: lucien xin <lucien.xin@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 15 Apr 2014 16:58:34 +0000 (12:58 -0400)]
ipv4: add a sock pointer to ip_queue_xmit()
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956fc ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956fc ("l2tp: keep original skb ownership") Reported-by: Zhan Jianyu <nasa4836@gmail.com> Tested-by: Zhan Jianyu <nasa4836@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xen/manage: Poweroff forcefully if user-space is not yet up.
The user can launch the guest in this sequence:
xl create -p /vm.cfg [launch, but pause it]
xl shutdown latest [sets control/shutdown=poweroff]
xl unpause latest
xl console latest [and see that the guest has completely
ignored the shutdown request]
In reality the guest hasn't ignored it. It registers a watch
and gets a notification that there is value. It then calls
the shutdown_handler which ends up calling orderly_shutdown.
Unfortunately that is so early in the bootup that there
are no user-space. Which means that the orderly_shutdown fails.
But since the force flag was set to false it continues on without
reporting.
What we really want to is to use the force when we are in the
SYSTEM_BOOTING state and not use the 'force' when SYSTEM_RUNNING.
However, if we are in the running state - and the shutdown command
has been given before the user-space has been setup, there is nothing
we can do. Worst yet, we stop ignoring the 'xl shutdown' requests!
As such, the other part of this patch is to only stop ignoring
the 'xl shutdown' when we are truly in the power off sequence.
That means the user can do multiple 'xl shutdown' and we will try
to act on them instead of ignoring them.
Fixes-Bug: http://bugs.xenproject.org/xen/bug/6 Reported-by: Alex Bligh <alex@alex.org.uk> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
The 'read_reply' works with 'process_msg' to read of a reply in XenBus.
'process_msg' is running from within the 'xenbus' thread. Whenever
a message shows up in XenBus it is put on a xs_state.reply_list list
and 'read_reply' picks it up.
The problem is if the backend domain or the xenstored process is killed.
In which case 'xenbus' is still awaiting - and 'read_reply' if called -
stuck forever waiting for the reply_list to have some contents.
This is normally not a problem - as the backend domain can come back
or the xenstored process can be restarted. However if the domain
is in process of being powered off/restarted/halted - there is no
point of waiting on it coming back - as we are effectively being
terminated and should not impede the progress.
This patch solves this problem by checking whether the guest is the
right domain. If it is an initial domain and hurtling towards death -
there is no point of continuing the wait. All other type of guests
continue with their behavior (as Xenstore is expected to still be
running in another domain).
Fixes-Bug: http://bugs.xenproject.org/xen/bug/8 Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The git commit a945928ea2709bc0e8e8165d33aed855a0110279
('xen: Do not enable spinlocks before jump_label_init() has executed')
was added to deal with the jump machinery. Earlier the code
that turned on the jump label was only called by Xen specific
functions. But now that it had been moved to the initcall machinery
it gets called on Xen, KVM, and baremetal - ouch!. And the detection
machinery to only call it on Xen wasn't remembered in the heat
of merge window excitement.
This means that the slowpath is enabled on baremetal while it should
not be.
Reported-by: Waiman Long <waiman.long@hp.com> Acked-by: Steven Rostedt <rostedt@goodmis.org> CC: stable@vger.kernel.org CC: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Boris Ostrovsky [Thu, 10 Apr 2014 16:17:09 +0000 (12:17 -0400)]
x86/xen: Fix 32-bit PV guests's usage of kernel_stack
Commit 198d208df4371734ac4728f69cb585c284d20a15 ("x86: Keep
thread_info on thread stack in x86_32") made 32-bit kernels use
kernel_stack to point to thread_info. That change missed a couple of
updates needed by Xen's 32-bit PV guests:
1. kernel_stack needs to be initialized for secondary CPUs
2. GET_THREAD_INFO() now uses %fs register which may not be the
kernel's version when executing xen_iret().
With respect to the second issue, we don't need GET_THREAD_INFO()
anymore: we used it as an intermediate step to get to per_cpu xen_vcpu
and avoid referencing %fs. Now that we are going to use %fs anyway we
may as well go directly to xen_vcpu.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Alexander Aring [Mon, 14 Apr 2014 16:48:02 +0000 (18:48 +0200)]
at86rf230: fix __at86rf230_read_subreg function
The __at86rf230_read_subreg function don't mask and shift register
contents which it should do. This patch adds the necessary masks and
shift operations in this function.
Since we have csma support this can make some trouble on state changes.
Since CSMA support turned on some bits in the TRX_STATUS register that
used to be zero, not masking broke checking of the TRX_STATUS field
after commanding a state change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Werner Almesberger <werner@almesberger.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Mon, 14 Apr 2014 16:48:01 +0000 (18:48 +0200)]
at86rf230: remove check if AVDD settled
The AVDD regulator is only enabled when the RF section is active TX_ON
(PLL_ON) state. Since commit 7dcbd22a97eb0689e6c583ad630ae0e7341e34c1
("ieee802154: ensure that first RF212 state comes from TRX_OFF").
We are in TRX_OFF state at the time at86rf230_hw_init is run.
Note that this test would only fail in case of a severe hardware
malfunction (faulty/shorted power supply, etc.) so it wasn't all that
useful in the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Werner Almesberger <werner@almesberger.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Mon, 14 Apr 2014 13:38:49 +0000 (15:38 +0200)]
net: cadence: Add architecture dependencies
The Cadence ethernet chipsets are only used on specific ARM
architectures. Add Kconfig dependencies so that drivers for these
chipsets are only buildable on the relevant architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fixes from Marcelo Tosatti:
- Fix for guest triggerable BUG_ON (CVE-2014-0155)
- CR4.SMAP support
- Spurious WARN_ON() fix
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove WARN_ON from get_kernel_ns()
KVM: Rename variable smep to cr4_smep
KVM: expose SMAP feature to guest
KVM: Disable SMAP for guests in EPT realmode and EPT unpaging mode
KVM: Add SMAP support when setting CR4
KVM: Remove SMAP bit from CR4_RESERVED_BITS
KVM: ioapic: try to recover if pending_eoi goes out of range
KVM: ioapic: fix assignment of ioapic->rtc_status.pending_eoi (CVE-2014-0155)
Pull bmc2835 crypto fix from Herbert Xu:
"This fixes a potential boot crash on bcm2835 due to the recent change
that now causes hardware RNGs to be accessed on registration"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm2835 - fix oops when rng h/w is accessed during registration
smp_read_barrier_depends() can be used if there is data dependency between
the readers - i.e. if the read operation after the barrier uses address
that was obtained from the read operation before the barrier.
In this file, there is only control dependency, no data dependecy, so the
use of smp_read_barrier_depends() is incorrect. The code could fail in the
following way:
* the cpu predicts that idx < entries is true and starts executing the
body of the for loop
* the cpu fetches map->extent[0].first and map->extent[0].count
* the cpu fetches map->nr_extents
* the cpu verifies that idx < extents is true, so it commits the
instructions in the body of the for loop
The problem is that in this scenario, the cpu read map->extent[0].first
and map->nr_extents in the wrong order. We need a full read memory barrier
to prevent it.
The following patchset contains three Netfilter fixes for your net tree,
they are:
* Fix missing generation sequence initialization which results in a splat
if lockdep is enabled, it was introduced in the recent works to improve
nf_conntrack scalability, from Andrey Vagin.
* Don't flush the GRE keymap list in nf_conntrack when the pptp helper is
disabled otherwise this crashes due to a double release, from Andrey
Vagin.
* Fix nf_tables cmp fast in big endian, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: Start with correct mac_len in skb_network_protocol
Sometimes, when the packet arrives at skb_mac_gso_segment()
its skb->mac_len already accounts for some of the mac lenght
headers in the packet. This seems to happen when forwarding
through and OpenSSL tunnel.
When we start looking for any vlan headers in skb_network_protocol()
we seem to ignore any of the already known mac headers and start
with an ETH_HLEN. This results in an incorrect offset, dropped
TSO frames and general slowness of the connection.
We can start counting from the known skb->mac_len
and return at least that much if all mac level headers
are known and accounted for.
Fixes: 53d6471cef17262d3ad1c7ce8982a234244f68ec (net: Account for all vlan headers in skb_mac_gso_segment) CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Daniel Borkman <dborkman@redhat.com> Tested-by: Martin Filip <nexus+kernel@smoula.net> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KVM: Disable SMAP for guests in EPT realmode and EPT unpaging mode
SMAP is disabled if CPU is in non-paging mode in hardware.
However KVM always uses paging mode to emulate guest non-paging
mode with TDP. To emulate this behavior, SMAP needs to be
manually disabled when guest switches to non-paging mode.
Daniel Borkmann [Mon, 14 Apr 2014 19:45:17 +0000 (21:45 +0200)]
Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
This reverts commit ef2820a735f7 ("net: sctp: Fix a_rwnd/rwnd management
to reflect real state of the receiver's buffer") as it introduced a
serious performance regression on SCTP over IPv4 and IPv6, though a not
as dramatic on the latter. Measurements are on 10Gbit/s with ixgbe NICs.
With the reverted patch applied, the SCTP/IPv4 performance is back
to normal on latest upstream for IPv4 and IPv6 and has same throughput
as 3.4.2 test kernel, steady and interval reports are smooth again.
Fixes: ef2820a735f7 ("net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer") Reported-by: Peter Butler <pbutler@sonusnet.com> Reported-by: Dongsheng Song <dongsheng.song@gmail.com> Reported-by: Fengguang Wu <fengguang.wu@intel.com> Tested-by: Peter Butler <pbutler@sonusnet.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com> Cc: Alexander Sverdlin <alexander.sverdlin@nsn.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 14 Apr 2014 19:20:12 +0000 (21:20 +0200)]
net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
While reviewing seccomp code, we found that BPF_S_ANC_SECCOMP_LD_W has
been wrongly decoded by commit a8fc927780 ("sk-filter: Add ability to
get socket filter program (v2)") into the opcode BPF_LD|BPF_B|BPF_ABS
although it should have been decoded as BPF_LD|BPF_W|BPF_ABS.
In practice, this should not have much side-effect though, as such
conversion is/was being done through prctl(2) PR_SET_SECCOMP. Reverse
operation PR_GET_SECCOMP will only return the current seccomp mode, but
not the filter itself. Since the transition to the new BPF infrastructure,
it's also not used anymore, so we can simply remove this as it's
unreachable.
Fixes: a8fc927780 ("sk-filter: Add ability to get socket filter program (v2)") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
These audit messages are being triggered via audit_seccomp() through
__secure_computing() in seccomp mode (BPF) filter with seccomp return
codes 0x30000 (== SECCOMP_RET_TRAP) and 0x50000 (== SECCOMP_RET_ERRNO)
during filter runtime. Moreover, Linus reports that x86_64 Chromium
seems fine.
The underlying issue that explains this is that the implementation of
populate_seccomp_data() is wrong. Our seccomp data structure sd that
is being shared with user ABI is:
Therefore, a simple cast to 'unsigned long *' for storing the value of
the syscall argument via syscall_get_arguments() is just wrong as on
32-bit x86 (or any other 32bit arch), it would result in storing a0-a5
at wrong offsets in args[] member, and thus i) could leak stack memory
to user space and ii) tampers with the logic of seccomp BPF programs
that read out and check for syscall arguments:
syscall_get_arguments(task, regs, 0, 1, (unsigned long *) &sd->args[0]);
Tested on 32-bit x86 with Google Chrome, unfortunately only via remote
test machine through slow ssh X forwarding, but it fixes the issue on
my side. So fix it up by storing args in type correct variables, gcc
is clever and optimizes the copy away in other cases, e.g. x86_64.
Fixes: bd4cf0ed331a ("net: filter: rework/optimize internal BPF interpreter's instruction set") Reported-and-bisected-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Eric Paris <eparis@redhat.com> Cc: James Morris <james.l.morris@oracle.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 14 Apr 2014 17:43:58 +0000 (13:43 -0400)]
Merge branch 'qlcnic'
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This patch series contains following bug fixes -
* Send INIT_NIC_FUNC mailbox command as first mailbox
* Fix a panic because of uninitialized delayed_work.
* Fix inconsistent calculation of max rings count.
* Fix PVID configuration issue. Driver needs to clear older
PVID before adding new one.
* Fix QLogic application/driver interface by packing vNIC information
array.
* Fix a crash when user tries to disable SR-IOV while VFs are
still assigned to VMs.
Please apply to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
o While disabling SR-IOV when VFs are assigned to VMs causes host crash
so return -EPERM when user request to disable SR-IOV using pci sysfs in
case of VFs are assigned to VMs.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
o Application expect vNIC number as the array index but driver interface
return configuration in array index form.
o Pack the vNIC information array in the buffer such that application can
access it using vNIC number as the array index.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clear older PVID before adding a newer PVID to the eSwicth port
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Do not read max rings count from qlcnic_get_nic_info(). Use driver defined
values for 82xx adapters. In case of 83xx adapters, use minimum of firmware
provided and driver defined values.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
o INIT_NIC_FUNC should be first mailbox sent. Sending DCB capability and
parameter query commands after that command.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
o AEN event was being received before initializing delayed_work struct
and handlers for it. This was resulting in crash. This patch fixes it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 14 Apr 2014 17:41:42 +0000 (13:41 -0400)]
Merge branch 'be2net'
Sathya Perla says:
====================
be2net: patch set
Patch 1/2 is a v2 of a patch that was submitted earlier (as a part of a
different patch-set). v2 incorporates a suggestion given by David Laight
for how long to poll for pending TX completions while disabling a device.
Patch 2/2 fixes a crash in be_remove()->be_close()
path after be2net has aborted an EEH error recovery
due to a permanant failure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Mon, 14 Apr 2014 10:42:41 +0000 (16:12 +0530)]
be2net: Fix invocation of be_close() after be_clear()
In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.
This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: Fix to reap TX compls till HW doesn't respond for some time
be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.
It is hard to calculate a "proper timeout value" that works in all
configurations. This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.
v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log