]> git.karo-electronics.de Git - karo-tx-uboot.git/log
karo-tx-uboot.git
12 years agoarm/davinci: fix DDR2/mDDR memory controller initialization for Omap L138
Mikhail Kshevetskiy [Mon, 9 Jul 2012 08:52:41 +0000 (08:52 +0000)]
arm/davinci: fix DDR2/mDDR memory controller initialization for Omap L138

follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
12 years agoRevert "arm: armv7: add compile option -mno-unaligned-access if available"
Albert ARIBAUD [Fri, 20 Jul 2012 06:51:26 +0000 (08:51 +0200)]
Revert "arm: armv7: add compile option -mno-unaligned-access if available"

This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.

12 years agoomap: am335x_evm: enable i2c1 channel
Steve Sakoman [Fri, 22 Jun 2012 07:45:57 +0000 (07:45 +0000)]
omap: am335x_evm: enable i2c1 channel

This patch sets up pinmux, enables fclk, and
defines CONFIG_I2C_MULTI_BUS

Signed-off-by: Steve Sakoman <steve@sakoman.com>
12 years agobeagle: removed unused pr_debug #define
Peter Meerwald [Mon, 2 Jul 2012 12:26:31 +0000 (12:26 +0000)]
beagle: removed unused pr_debug #define

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
12 years agobeagle: fix termination of buddy env setting
Peter Meerwald [Mon, 2 Jul 2012 03:43:31 +0000 (03:43 +0000)]
beagle: fix termination of buddy env setting

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
12 years agobeagle: make get_expansion_id(), get_board_revision(), beagle_display_init() static
Peter Meerwald [Mon, 2 Jul 2012 03:19:03 +0000 (03:19 +0000)]
beagle: make get_expansion_id(), get_board_revision(), beagle_display_init() static

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
12 years agoigep00x0: default mmcrootfstype to EXT4
Javier Martinez Canillas [Fri, 29 Jun 2012 02:45:41 +0000 (02:45 +0000)]
igep00x0: default mmcrootfstype to EXT4

omap2plus_defconfig now has built-in compile support for EXT4 enabled
by default now. So, we can use EXT4 as the default root file system
type for MMC.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
12 years agoigep00x0: default to OMAP-specific serial driver
Javier Martinez Canillas [Fri, 29 Jun 2012 02:45:40 +0000 (02:45 +0000)]
igep00x0: default to OMAP-specific serial driver

An OMAP specific serial driver was merged on the Linux kenel a long
time ago. So, it makes sense to default the console name to OMAP
ttyO instead of the generic ttyS naming.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
12 years agoda850/omap-l138: add support for direct NOR boot mode
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:23 +0000 (21:35 +0000)]
da850/omap-l138: add support for direct NOR boot mode

This patch adds support for direct NOR boot mode on
da850/omap-l138. Added da850evm_direct_nor entry in
boards.cfg to allow to build targets.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: Add support for NAND SPL
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:22 +0000 (21:35 +0000)]
da850/omap-l138: Add support for NAND SPL

This patch adds configuration required for NAND SP
on DA850/OMAP-L138.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: Fix NAND flash timings
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:21 +0000 (21:35 +0000)]
da850/omap-l138: Fix NAND flash timings

Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x08222204, where as currently it
configured to 0x00100084 in U-Boot. This issue was found out when
support for NAND SPL is added in U-Boot. Without this patch U-Boot
does not come up with SPL.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: Add support to read u-boot image from MMC/SD
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:20 +0000 (21:35 +0000)]
da850/omap-l138: Add support to read u-boot image from MMC/SD

DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.

Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: Define SPI specific configs for SPL only when SPI is used
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:19 +0000 (21:35 +0000)]
da850/omap-l138: Define SPI specific configs for SPL only when SPI is used

define SPI specific configs for SPL only when CONFIG_USE_SPIFLASH
config is defined

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoarm, davinci: perform check for initializing global data and serial init
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:18 +0000 (21:35 +0000)]
arm, davinci: perform check for initializing global data and serial init

initialize baudrate, flags, data and serial initialization,
only when CONFIG_SPL_LIBCOMMON_SUPPORT is defined.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
12 years agoda850/omap-l138: Make MMC and NOR support mutually exclusive
Rajashekhara, Sudhakar [Sun, 24 Jun 2012 21:35:17 +0000 (21:35 +0000)]
da850/omap-l138: Make MMC and NOR support mutually exclusive

On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot
work together. This patch enables the MMC/SD support only
when NOR support is disabled. NOR Flash identification works
even without this patch, but erase and write will have issues.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM
Rajashekhara, Sudhakar [Sun, 24 Jun 2012 21:35:16 +0000 (21:35 +0000)]
da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM

AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoda850/omap-l138: Add MMC support for DA850/OMAP-L138
Lad, Prabhakar [Sun, 24 Jun 2012 21:35:15 +0000 (21:35 +0000)]
da850/omap-l138: Add MMC support for DA850/OMAP-L138

This patch adds support for MMC/SD on DA850/OMAP-L138.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
12 years agoomap: am33xx: enable gpio support
Steve Sakoman [Mon, 4 Jun 2012 05:35:34 +0000 (05:35 +0000)]
omap: am33xx: enable gpio support

This patch uses the code in omap-common to support gpio modules 1-3
on am33xx based boards.

It adds base address and register definitions, enables clocks to the
modules, and enables building the common gpio code for CONFIG_AM33XX
as well as CONFIG_OMAP

Signed-off-by: Steve Sakoman <steve@sakoman.com>
12 years agoomap: am335x_evm: remove unused definitions
Steve Sakoman [Mon, 4 Jun 2012 05:26:14 +0000 (05:26 +0000)]
omap: am335x_evm: remove unused definitions

UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h

PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
12 years agoOMAP3: mcx: read hot-water-button after reset
Stefano Babic [Wed, 13 Jun 2012 22:34:44 +0000 (22:34 +0000)]
OMAP3: mcx: read hot-water-button after reset

Detect hot-water-button to start a differnt image.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
12 years agoOMAP3: mcx: updated default environment
Stefano Babic [Wed, 13 Jun 2012 22:34:43 +0000 (22:34 +0000)]
OMAP3: mcx: updated default environment

Patch drops also not used CFI setup in the
configuration file.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
12 years agoOMAP3: mcx: set pinmux for uart4
Stefano Babic [Wed, 13 Jun 2012 22:34:42 +0000 (22:34 +0000)]
OMAP3: mcx: set pinmux for uart4

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
12 years agomcx: increased buffer for command line
Stefano Babic [Wed, 13 Jun 2012 22:34:41 +0000 (22:34 +0000)]
mcx: increased buffer for command line

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
12 years agoarm: omap3: cm-t35: minor comment and printf change
Igor Grinberg [Wed, 13 Jun 2012 19:41:40 +0000 (19:41 +0000)]
arm: omap3: cm-t35: minor comment and printf change

Fix the comment to reflect the actual function call time.
Change the printf message to look nicer in the context it might be printed.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
12 years agohawkboard/omapl-138: Add support for generating ais image for hawkboard
Sughosh Ganu [Wed, 13 Jun 2012 08:39:06 +0000 (08:39 +0000)]
hawkboard/omapl-138: Add support for generating ais image for hawkboard

Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
12 years agoomap24xx_i2c: add 2-byte address support
Ilya Yanok [Fri, 8 Jun 2012 03:12:09 +0000 (03:12 +0000)]
omap24xx_i2c: add 2-byte address support

Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.

Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.

CC: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
12 years agoCREDITS: Add credits for MCF5249 initialization code
Jeremy Andrus [Mon, 13 Aug 2012 14:49:51 +0000 (14:49 +0000)]
CREDITS: Add credits for MCF5249 initialization code

Signed-off-by: Wolfgang Denk <wd@denx.de>
12 years agoConsolidate bootcount code into drivers/bootcount
Stefan Roese [Thu, 16 Aug 2012 17:55:41 +0000 (17:55 +0000)]
Consolidate bootcount code into drivers/bootcount

This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
12 years agompc52xx: remove o2dnt board
Anatolij Gustschin [Fri, 31 Aug 2012 01:30:44 +0000 (01:30 +0000)]
mpc52xx: remove o2dnt board

Remove old o2dnt board without OF support. New support for this board
is added by the previous patch, O2I configuration.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
12 years agompc52xx: add common o2dnt and o2dnt2 support and configurations
Anatolij Gustschin [Fri, 31 Aug 2012 01:29:57 +0000 (01:29 +0000)]
mpc52xx: add common o2dnt and o2dnt2 support and configurations

Add common code for o2dnt and o2dnt2 based boards and add different
board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and
O3DNT boards.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
12 years agompc5xxx: add GPIO port configuration
Anatolij Gustschin [Sun, 12 Aug 2012 23:38:10 +0000 (23:38 +0000)]
mpc5xxx: add GPIO port configuration

Add posibility for board specifig GPIO configurations using
various CONFIG_SYS_ macros.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
12 years agompc5xxx: add pci_mpc5xxx_init prototype to common header
Anatolij Gustschin [Sun, 12 Aug 2012 23:38:09 +0000 (23:38 +0000)]
mpc5xxx: add pci_mpc5xxx_init prototype to common header

Add pci_mpc5xxx_init() prototype to the header file, so board .c files
do not need to add extern pci_mpc5xxx_init() declaration.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
12 years agoMerge branch 'master' of git://git.denx.de/u-boot-sh
Wolfgang Denk [Sat, 1 Sep 2012 12:09:41 +0000 (14:09 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh

* 'master' of git://git.denx.de/u-boot-sh:
  sh: tmu: Removed arch/sh/include/asm/clk.h
  sh: tmu: Changed switch statement to shift operation
  sh: tmu: Changed TMU driver using array of structures

Signed-off-by: Wolfgang Denk <wd@denx.de>
12 years agoMerge branch 'sf' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Sat, 1 Sep 2012 10:22:31 +0000 (12:22 +0200)]
Merge branch 'sf' of git://git.denx.de/u-boot-blackfin

* 'sf' of git://git.denx.de/u-boot-blackfin:
  sf: spansion: Add support for S25FL256S
  sf: winbond: fix page_size
  sf: stmicro: add support for N25Q128A
  sf: stmicro: add support N25Q128 parts
  sf: stmicro: support JEDEC standard two-byte signature
  sf: winbond: add W25Q32
  cmd_spi: remove superfluous semicolon

Signed-off-by: Wolfgang Denk <wd@denx.de>
12 years agosh: tmu: Removed arch/sh/include/asm/clk.h
Nobuhiro Iwamatsu [Tue, 21 Aug 2012 05:37:34 +0000 (14:37 +0900)]
sh: tmu: Removed arch/sh/include/asm/clk.h

asm/clk.h was included get_peripheral_clk_rate function. But this
is not used from anywhere.
This removed asm/clk.h, and deleted include line from arch/sh/lib/time.c

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agosh: tmu: Changed switch statement to shift operation
Nobuhiro Iwamatsu [Tue, 21 Aug 2012 04:24:43 +0000 (13:24 +0900)]
sh: tmu: Changed switch statement to shift operation

Calculation of the bit position using switch statement can substitute
shift operation using ffs.
And removed unsed macro and variable.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agosh: tmu: Changed TMU driver using array of structures
Nobuhiro Iwamatsu [Tue, 21 Aug 2012 04:14:46 +0000 (13:14 +0900)]
sh: tmu: Changed TMU driver using array of structures

This changed into access using array of structure from access to the register
using the definition of the register by macro.
And removed white space.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agoMakefile: fix HAVE_VENDOR_COMMON_LIB
Scott Wood [Tue, 14 Aug 2012 01:44:29 +0000 (01:44 +0000)]
Makefile: fix HAVE_VENDOR_COMMON_LIB

Commit 8b5a02640adf77301f943e8754992c50df004e8a ("Makefile: cosmetic:
optimize usage of LIBS-y") broke the build of boards that have a board
vendor "common" directory, by introducing a space between "LIBS-" and
"y".

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
12 years agosf: spansion: Add support for S25FL256S
Michal Simek [Tue, 14 Aug 2012 11:11:22 +0000 (13:11 +0200)]
sf: spansion: Add support for S25FL256S

Add support for Spansion S25FL256S SPI flash.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agosf: winbond: fix page_size
Stephen Warren [Mon, 13 Aug 2012 22:46:21 +0000 (16:46 -0600)]
sf: winbond: fix page_size

Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size
from 256 to 4096. This prevents either/both of "sf write" writing the
correct data, or "sf read" from reading the correct data back.

This allows U-Boot running on Compulab Tegra to upgrade itself.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agomtd/cfi_flash: fix write problems for Numonyx P33/30 32 MBit flashs
Holger Brunck [Thu, 9 Aug 2012 08:22:41 +0000 (10:22 +0200)]
mtd/cfi_flash: fix write problems for Numonyx P33/30 32 MBit flashs

commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips

fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
12 years agocfi_flash: add support for Spansion flash PPB sector protection
Anatolij Gustschin [Thu, 9 Aug 2012 06:18:12 +0000 (08:18 +0200)]
cfi_flash: add support for Spansion flash PPB sector protection

Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
12 years agodts/Makefile: Turn off some predefined macros
Horst Kronstorfer [Fri, 13 Jul 2012 03:03:40 +0000 (03:03 +0000)]
dts/Makefile: Turn off some predefined macros

Add '-ansi' to DTS_CPPFLAGS to avoid unwanted expansion of dts content
that matches some predefined macros.

Example: A number of PowerPC related *.dts files in the kernel define a
property named 'linux,network-index' which (w/o '-ansi') is expanded to
'1,network-index' by the preprocessor because of '#define linux 1.'

Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
12 years agoAdd support for DS1388.
Kenth Eriksson [Thu, 12 Jul 2012 19:59:44 +0000 (19:59 +0000)]
Add support for DS1388.

Support for DS1388 is added by extending the DS1337 driver. DS1388 is
similar to DS1337. The time registers are offset by 1 (due to support
for hundreds of seconds), and there is no century bit.
The configuration and trickle charge registers are also different.
Tested on hardware with Freescale P2010 and DS1388.

Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
12 years agodts/Makefile: Check for empty $(LDSCRIPT)
Horst Kronstorfer [Thu, 12 Jul 2012 02:58:32 +0000 (02:58 +0000)]
dts/Makefile: Check for empty $(LDSCRIPT)

Make sure that $(LDSCRIPT) is not empty before calling process_lds
with 'cat $(LDSCRIPT)' else cat will block waiting for input from
stdin.

Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
12 years agoMakefile: cosmetic: optimize usage of LIBS-y
Daniel Schwierzeck [Thu, 19 Jul 2012 13:39:58 +0000 (13:39 +0000)]
Makefile: cosmetic: optimize usage of LIBS-y

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
12 years agoMakefile: replace LIBS by LIBS-y
Daniel Schwierzeck [Thu, 28 Jun 2012 06:45:20 +0000 (06:45 +0000)]
Makefile: replace LIBS by LIBS-y

Synchronize with ALL-y handling and code in spl/Makefile.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
12 years agoMakefile: allow appending to LIB in sub-makefiles
Daniel Schwierzeck [Thu, 28 Jun 2012 06:45:19 +0000 (06:45 +0000)]
Makefile: allow appending to LIB in sub-makefiles

The top Makefile and the SPL Makefile have lines like those:

ifneq ($(CONFIG_AM33XX)$(CONFIG_OMAP34XX)$(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),)
LIBS += $(CPUDIR)/omap-common/libomap-common.o
endif

ifeq ($(SOC),mx5)
LIBS += $(CPUDIR)/imx-common/libimx-common.o
endif

This should be done in the arch/CPU/SoC specific sub-makefiles to
keep the top Makefiles clean. This patch also allows adding of new
arch/CPU/SoC specific libraries in the future without touching
the top Makefiles.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
12 years agonds32: fix unused pmu_init warning
Mike Frysinger [Mon, 6 Aug 2012 13:46:37 +0000 (13:46 +0000)]
nds32: fix unused pmu_init warning

Fixes the build-time warning:
board.c: At top level:
board.c:106: warning: 'pmu_init' defined but not used

This makes the ifdef logic at the call site match the logic at the
function definition.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agonds32: delete unused local variable
Mike Frysinger [Mon, 6 Aug 2012 13:46:36 +0000 (13:46 +0000)]
nds32: delete unused local variable

Fixes the build-time warning:
board.c: In function 'board_init_r':
board.c:304: warning: unused variable 's'

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agonds32: drop bi_enetaddr from global data
Mike Frysinger [Mon, 6 Aug 2012 13:46:35 +0000 (13:46 +0000)]
nds32: drop bi_enetaddr from global data

Nothing is using this, so punt it from the gd.  Seems to just be a copy
& paste wart from the initial port.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agosf: stmicro: add support for N25Q128A
Michal Simek [Fri, 10 Aug 2012 12:21:46 +0000 (14:21 +0200)]
sf: stmicro: add support for N25Q128A

Add support for Numonyx N25Q128A SPI flash.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agosf: stmicro: add support N25Q128 parts
Stephan Linz [Thu, 2 Aug 2012 18:47:30 +0000 (20:47 +0200)]
sf: stmicro: add support N25Q128 parts

Adds support for Numonyx's N25Q128 SPI flash. These devices
are used on (among others) Avnet Spartan-6 LX9 micro-evaluation
boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agosf: stmicro: support JEDEC standard two-byte signature
Stephan Linz [Thu, 2 Aug 2012 18:47:29 +0000 (20:47 +0200)]
sf: stmicro: support JEDEC standard two-byte signature

There are more than the M25Pxx serial flashs that can be
used with the stmicro driver, for example: the M25PXxx or
N25Qxx serie. All these chips have burned in the original
stmicro manufacture id 0x20 together with a standard
two-byte signature.

In preperation to support all these chips the stmicro driver
have to decode the full two-byte signature.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agosf: winbond: add W25Q32
Rajeshwari Shinde [Thu, 2 Aug 2012 07:25:05 +0000 (12:55 +0530)]
sf: winbond: add W25Q32

SMDK EVT1  has a different Winbond part, added its part details
to the SPI flash table.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agocmd_spi: remove superfluous semicolon
Marek Vasut [Wed, 1 Aug 2012 13:12:15 +0000 (15:12 +0200)]
cmd_spi: remove superfluous semicolon

Reported-by: James Miller <jamesmiller@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agozfs: Add ZFS filesystem support
Jorgen Lundman [Thu, 19 Jul 2012 20:48:25 +0000 (20:48 +0000)]
zfs: Add ZFS filesystem support

U-Boot port is based on sources forked from GRUB-0.97 by Sun in 2004,
which can be found here:
http://src.opensolaris.org/source/xref/onnv/onnv-gate/usr/src/grub/grub-0.97/stage2/zfs-include/zfs.h

Released by Sun for GRUB under the license:
  *  This program is free software; you can redistribute it and/or modify
  *  it under the terms of the GNU General Public License as published by
  *  the Free Software Foundation; either version 2 of the License, or
  *  (at your option) any later version.

GRUB official releases include ZFS in version:
ftp://alpha.gnu.org/gnu/grub/grub-1.99~rc1.tar.gz

And patched against GRUB Bazaar repository for ashift fixes (4KB HDDs)
more conveniently found at github:
https://github.com/pendor/grub-zfs/commit/e7b6ef3ac3b9685ac4c394c897b1d4221b7381f1

Signed-off-by: Jorgen Lundman <lundman@lundman.net>
12 years agou-boot: Update yaffs2 file system
Charles Manning [Wed, 9 May 2012 16:55:17 +0000 (16:55 +0000)]
u-boot: Update yaffs2 file system

This patch updates the yaffs2 in u-boot to correspond to
git://www.aleph1.co.uk/yaffs2
commit id 9ee5d0643e559568dbe62215f76e0a7bd5a63d93

Signed-off-by: Charles Manning <cdhmanning@gmail.com>
12 years agoopenrisc: Work around potential relocation issues
Julius Baxter [Sat, 5 May 2012 12:32:11 +0000 (12:32 +0000)]
openrisc: Work around potential relocation issues

When reset code is in flash, the jump instructions emitted by the
compiler are relative instead of absolute jumps.

A fix to the reset code to make correct jumps to the beginning of
code relocated to RAM have also been added.

Signed-off-by: Julius Baxter <juliusbaxter@gmail.com>
12 years agorename EB+MCF-EV123 to its current marketing name EB+CPU5282
Jens Scharsig [Wed, 2 May 2012 00:57:08 +0000 (00:57 +0000)]
rename EB+MCF-EV123 to its current marketing name EB+CPU5282

* rename board directory to eb_cpu5282
* rename EB+MCF-EV123_.*config to eb_cpu5282_.*config
* add Maintainer for EB+CPU5282 board
* rename prompt

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
12 years agoConsider CONFIG_ZERO_BOOTDELAY_CHECK when CONFIG_AUTOBOOT_KEYED is set
Dirk Eibach [Thu, 26 Apr 2012 01:49:33 +0000 (01:49 +0000)]
Consider CONFIG_ZERO_BOOTDELAY_CHECK when CONFIG_AUTOBOOT_KEYED is set

When CONFIG_ZERO_BOOTDELAY_CHECK is not defined, bootdelay==0
prevents the check for console input (as stated in README.autoboot).
This must also work in CONFIG_AUTOBOOT_KEYED mode.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
12 years agomkconfig: add support for SPL CPU
Allen Martin [Thu, 19 Apr 2012 07:58:57 +0000 (07:58 +0000)]
mkconfig: add support for SPL CPU

Add support for specifying a differnt CPU for main u-boot and SPL
u-boot builds.  This is done by adding an optional SPL CPU after the
main CPU in boards.cfg as follows:

     normal_cpu:spl_cpu

This this case CPU will be set to "normal_cpu" during the main u-boot
build and "spl_cpu" during the SPL build.

Signed-off-by: Allen Martin <amartin@nvidia.com>
12 years agoconfigs: Remove unused symbol CONFIG_DISCOVER_PHY
Fabio Estevam [Fri, 13 Apr 2012 05:51:36 +0000 (05:51 +0000)]
configs: Remove unused symbol CONFIG_DISCOVER_PHY

CONFIG_DISCOVER_PHY is not used anywhere, so remove it from config files.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
12 years agoBuild: Ignore build tree and IDE control file
Timo Ketola [Wed, 11 Apr 2012 23:33:49 +0000 (23:33 +0000)]
Build: Ignore build tree and IDE control file

Signed-off-by: Timo Ketola <timo@exertus.fi>
12 years agopowerpc: Fix declaration type for I/O functions
Prabhakar Kushwaha [Tue, 10 Apr 2012 22:49:12 +0000 (22:49 +0000)]
powerpc: Fix declaration type for I/O functions

Prototype declaration of I/O operation functions are not correct. as both
'extern' and function definition are at same place.

Chage protoype declaration as static.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
12 years agopowerpc:Fix return type & parameter passed for I/O functions
Prabhakar Kushwaha [Tue, 10 Apr 2012 22:48:59 +0000 (22:48 +0000)]
powerpc:Fix return type & parameter passed for I/O functions

Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type
u8/u16/u32.
Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type
uniform across the file changed to u32

Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32
should not be 'int'.Change it to type u8/u16/u32.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
12 years agoUBIFS: Improve error message when reading superblock failed
Bernhard Walle [Mon, 2 Apr 2012 01:58:34 +0000 (01:58 +0000)]
UBIFS: Improve error message when reading superblock failed

In addition to the error message also display the error code. I had the
problem that my malloc memory was not enough (ENOMEM), and if u-boot
had displayed the error code immediately that would have saved me some
debugging.

Signed-off-by: Bernhard Walle <walle@corscience.de>
Use ubifs_err instead of printf.
Add "errno=%d" in output as suggested by Albert Aribaud.

Signed-off-by: Thomas Weber <weber@corscience.de>
12 years agosandbox: Add basic test for command execution
Simon Glass [Fri, 30 Mar 2012 21:30:58 +0000 (21:30 +0000)]
sandbox: Add basic test for command execution

Since run_command() and run_command_list() are important and a little
confusing, add some basic tests to check that the behaviour is correct.

Note: I am not sure that this should be committed, nor where it should go
in the source tree. Comments welcome.

To run the unit tests use the ut_cmd command available in sandbox:

make sandbox_config
make
./u-boot -c ut_cmd

(To test both hush and built-in parsers, you need to manually change
CONFIG_SYS_HUSH_PARSER in include/configs/sandbox.h and build/run again)

Signed-off-by: Simon Glass <sjg@chromium.org>
12 years agoAllow newlines within command environment vars
Simon Glass [Fri, 30 Mar 2012 21:30:56 +0000 (21:30 +0000)]
Allow newlines within command environment vars

Any environment variable can hold commands to be executed by the 'run'
command. The environment variables preboot, bootcmd and menucmd have
special code for triggering execution in certain circumstances.

We adjust these calls to use run_command_list() instead of run_command().
This change permits these variables to have embedded newlines so that
they work the same as the 'source' command.

Signed-off-by: Simon Glass <sjg@chromium.org>
12 years agoAdd run_command_list() to run a list of commands
Simon Glass [Fri, 30 Mar 2012 21:30:55 +0000 (21:30 +0000)]
Add run_command_list() to run a list of commands

This new function runs a list of commands separated by semicolon or newline.
We move this out of cmd_source so that it can be used by other code. The
PXE code also uses the new function.

Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Simon Glass <sjg@chromium.org>
12 years agoMalloc: Fix -Wundef warnings
Marek Vasut [Thu, 29 Mar 2012 09:28:15 +0000 (09:28 +0000)]
Malloc: Fix -Wundef warnings

In file included from arch/arm/lib/board.c:43:0:
include/malloc.h:490:5: warning: "HAVE_MMAP" is not defined [-Wundef]
include/malloc.h:590:5: warning: "HAVE_USR_INCLUDE_MALLOC_H" is not defined [-Wundef]
include/malloc.h:757:5: warning: "HAVE_MMAP" is not defined [-Wundef]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
12 years agoglobal_data: unify global flag defines
Mike Frysinger [Sun, 18 Mar 2012 14:31:24 +0000 (14:31 +0000)]
global_data: unify global flag defines

All the global flag defines are the same across all arches.  So unify them
in one place, and add a simple way for arches to extend for their needs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
12 years agoMAKEALL: Allow empty ERR directory
Andy Fleming [Wed, 8 Aug 2012 14:12:30 +0000 (14:12 +0000)]
MAKEALL: Allow empty ERR directory

If we build everything correctly with multiple builds, and an
ERR directory had been previously created, we failed to report
that everything was fine because grep failed to find anything
in the ERR directory. Use grep -r, which doesn't complain if
there are no input files.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Tom Rini <trini@ti.com>
12 years agoMerge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Wolfgang Denk [Thu, 9 Aug 2012 19:04:05 +0000 (21:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
  powerpc/mpc85xx: Ignore E bit for BSC9130/1
  powerpc/sgmii: To support PHY link state auto detect in SGMII mode
  powerpc/85xx: improve definition of BR_PHYS_ADDR macro
  powerpc/p2041: configure the CPLD lane_mux according to RCW
  powerpc/ddr: fix fsl_ddr_get_dimm_params compile error
  powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
  powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
  powerpc/p1022ds: fix DIU/LBC switching with NAND enabled
  powerpc/p1022ds: add support for SPI and SD boot

Signed-off-by: Wolfgang Denk <wd@denx.de>
12 years agopowerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
Timur Tabi [Wed, 25 Jul 2012 11:03:34 +0000 (11:03 +0000)]
powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs

The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for.  The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/mpc85xx: Ignore E bit for BSC9130/1
York Sun [Fri, 20 Jul 2012 10:59:38 +0000 (10:59 +0000)]
powerpc/mpc85xx: Ignore E bit for BSC9130/1

Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/sgmii: To support PHY link state auto detect in SGMII mode
Hongtao Jia [Wed, 11 Jul 2012 23:39:53 +0000 (23:39 +0000)]
powerpc/sgmii: To support PHY link state auto detect in SGMII mode

PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.

For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/85xx: improve definition of BR_PHYS_ADDR macro
Timur Tabi [Fri, 6 Jul 2012 07:39:26 +0000 (07:39 +0000)]
powerpc/85xx: improve definition of BR_PHYS_ADDR macro

The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/p2041: configure the CPLD lane_mux according to RCW
Shaohui Xie [Thu, 28 Jun 2012 23:37:25 +0000 (23:37 +0000)]
powerpc/p2041: configure the CPLD lane_mux according to RCW

Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.

Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.

Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/ddr: fix fsl_ddr_get_dimm_params compile error
Shaohui Xie [Thu, 28 Jun 2012 23:36:38 +0000 (23:36 +0000)]
powerpc/ddr: fix fsl_ddr_get_dimm_params compile error

fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
Shaohui Xie [Thu, 28 Jun 2012 23:35:34 +0000 (23:35 +0000)]
powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined

ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined
and non-NOR u-boot is building, it will cause compile error. Also, add
CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash
write performance.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
York Sun [Mon, 21 May 2012 08:43:11 +0000 (08:43 +0000)]
powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB

The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/p1022ds: fix DIU/LBC switching with NAND enabled
Timur Tabi [Fri, 18 May 2012 09:09:09 +0000 (09:09 +0000)]
powerpc/p1022ds: fix DIU/LBC switching with NAND enabled

In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead.  Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agopowerpc/p1022ds: add support for SPI and SD boot
Matthew McClintock [Fri, 18 May 2012 06:04:17 +0000 (06:04 +0000)]
powerpc/p1022ds: add support for SPI and SD boot

Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.

Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.

Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
12 years agosh: Add support pin function control using GPIO
Nobuhiro Iwamatsu [Thu, 21 Jun 2012 02:26:38 +0000 (11:26 +0900)]
sh: Add support pin function control using GPIO

Renesas SH and R-Mobile set up device using PFC.
This provide the framework. Most codes were brought from linux kernel.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agoserial: sh: Add support Renesas R8A7740
Hideyuki Sano [Mon, 25 Jun 2012 01:29:56 +0000 (10:29 +0900)]
serial: sh: Add support Renesas R8A7740

The serial device of R8A7740 has the same structure as SH7372 of SH, etc.

Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agoserial: sh: Add support Renesas SH73A0
Nobuhiro Iwamatsu [Thu, 21 Jun 2012 04:21:32 +0000 (13:21 +0900)]
serial: sh: Add support Renesas SH73A0

The serial device of SH73A0 has the same structure as SH7372 of SH, etc.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agosh: modify checkcpu() for SH-4A
Yoshihiro Shimoda [Mon, 23 Jul 2012 14:53:42 +0000 (14:53 +0000)]
sh: modify checkcpu() for SH-4A

Even if using CPU is SH-4A, the previous code always put "SH4".
This patch fixes it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
12 years agoMerge branch 'master' of git://git.denx.de/u-boot-onenand
Wolfgang Denk [Tue, 7 Aug 2012 21:42:55 +0000 (23:42 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-onenand

* 'master' of git://git.denx.de/u-boot-onenand:
  env_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE

Signed-off-by: Wolfgang Denk <wd@denx.de>
12 years agoMAINTAINERS: cleanup for km ppc boards
Holger Brunck [Mon, 6 Aug 2012 02:16:33 +0000 (02:16 +0000)]
MAINTAINERS: cleanup for km ppc boards

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
12 years agospi: Fix merge conflicts - Makefile
Michal Simek [Fri, 3 Aug 2012 03:37:44 +0000 (03:37 +0000)]
spi: Fix merge conflicts - Makefile

The patch "spi: tegra2: rename tegra2_spi.* to tegra_spi.*"
(sha1: edffa63d3d6e76991998789f9fcbaa483731ca65)
renamed tegra2_spi.c to tegra_spi.c

and the patch "Merge branch 'master' of git://git.denx.de/u-boot-microblaze"
(sha1: d978780b2e676c005460cd561f4f15b5220bdf49)

has wrongly resolved confict.

This patch fix it.

Signed-off-by: Michal Simek <monstr@monstr.eu>
12 years agoext2fs: fix warning: 'blocknxt' may be used uninitialized with gcc 4.2
Tom Rini [Tue, 7 Aug 2012 16:58:34 +0000 (09:58 -0700)]
ext2fs: fix warning: 'blocknxt' may be used uninitialized with gcc 4.2

The above warning was introduced originally in 436da3c "ext2load:
increase read speed" and fixed for newer toolchains in b803273 "ext2fs:
fix warning: 'blocknxt' may be used uninitialized".  This change did not
fix the warning with gcc 4.2, as found in ELDK 4.2.

If we rework the while loop to initalize blocknxt before entering the
warning really goes away.  Tested on am335x with an approx 7mb file and
crc32 in U-Boot befor and after this change.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
12 years agoenv_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE
David du Colombier [Wed, 13 Jun 2012 21:24:35 +0000 (23:24 +0200)]
env_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE

This fix prevents env_import() CRC to fail when CONFIG_ENV_SIZE
is not equal to 4096 bytes
It also prevents mtd->read and mtd->write to be incomplete when
the environment is larger than 4096 bytes.

Signed-off-by: David du Colombier <0intro@gmail.com>
12 years agopowerpc/82xx: adapt SDRAM settings for mgcoge3ne
Gerlando Falauto [Fri, 27 Jul 2012 05:16:40 +0000 (05:16 +0000)]
powerpc/82xx: adapt SDRAM settings for mgcoge3ne

The HW guys suggested to change these two values. And these values are
now identical to the values we use on mgcoge.

PSDMR_WRC was set to 1C as it should lead to better performance.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
12 years agopowerpc/82xx: use SDRAM detection for mgcoge2ne
Gerlando Falauto [Fri, 27 Jul 2012 05:16:39 +0000 (05:16 +0000)]
powerpc/82xx: use SDRAM detection for mgcoge2ne

mgcoge2ne was an intermediate step towards mgcoge3ne. One difference is the
smaller SDRAM on mgcoge2ne (128MB). To support both boards with the same
u-boot we use here the SDRAM detection.

This patch enables SDRAM detection between 256MB and 128MB.
So in addition to the existing 256MB geometry:
     4 chips x 8M (13 rows, 10 cols) x 16 bit x 4 banks
we can now also have 128MB geometry:
     4 chips x 4M (13 rows,  9 cols) x 16 bit x 4 banks

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
12 years agopowerpc/82xx: add SDRAM detection for km82xx
Gerlando Falauto [Fri, 27 Jul 2012 05:16:38 +0000 (05:16 +0000)]
powerpc/82xx: add SDRAM detection for km82xx

This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
12 years agopowerpc/82xx: move km/km82xx-common.h within km82xx.h
Gerlando Falauto [Fri, 27 Jul 2012 05:16:37 +0000 (05:16 +0000)]
powerpc/82xx: move km/km82xx-common.h within km82xx.h

The only file including km82xx-common.h is km82xx.h.
So there is no need to have it as a separate file.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
12 years agopowerpc/82xx: merge mgcoge.h and mgcoge3ne.h into km82xx.h
Gerlando Falauto [Mon, 30 Jul 2012 08:22:30 +0000 (08:22 +0000)]
powerpc/82xx: merge mgcoge.h and mgcoge3ne.h into km82xx.h

Since mgcoge and mgcoge3ne are the only km82xx boards, there is no need
to keep them as separate .h config files.
Therefore, make mgcoge3ne.h and mgcoge.h converge into a single km82xx.h
file.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
12 years agopowerpc/82xx: move mgcoge, mgcoge3ne defines to ease subsequent merge
Gerlando Falauto [Fri, 27 Jul 2012 05:16:35 +0000 (05:16 +0000)]
powerpc/82xx: move mgcoge, mgcoge3ne defines to ease subsequent merge

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
12 years agopowerpc/82xx: remove unused define for mgcoge3ne
Holger Brunck [Fri, 27 Jul 2012 05:16:34 +0000 (05:16 +0000)]
powerpc/82xx: remove unused define for mgcoge3ne

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>