By clearing the GPU read domains before waiting upon the buffer, we run
the risk of the wait being interrupted and the domains prematurely
cleared. The next time we attempt to wait upon the buffer (after
userspace handles the signal), we believe that the buffer is idle and so
skip the wait.
There are a number of bugs across all generations which show signs of an
overly haste reuse of active buffers.
A couple of those pre-date i915_gem_object_finish_gpu(), so may be
unrelated (such as a wild write from a userspace command buffer), but
this does look like a convincing cause for most of those bugs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In super_1_sync (the first hunk) we need to clear 'changed' before
checking read_seqretry(), otherwise we might race with other code
adding a bad block and so won't retry later.
In md_update_sb (the second hunk), in the case where there is no
metadata (neither persistent nor external), we treat any bad blocks as
an error. However we need to clear the 'changed' flag before calling
md_ack_all_badblocks, else it won't do anything.
This patch is suitable for -stable release 3.0 and later.
If RAID1 or RAID10 is used under LVM or some other stacking
block device, it is possible to enter a deadlock during
resync or recovery.
This can happen if the upper level block device creates
two requests to the RAID1 or RAID10. The first request gets
processed, blocks recovery and queue requests for underlying
requests in current->bio_list. A resync request then starts
which will wait for those requests and block new IO.
But then the second request to the RAID1/10 will be attempted
and it cannot progress until the resync request completes,
which cannot progress until the underlying device requests complete,
which are on a queue behind that second request.
So allow that second request to proceed even though there is
a resync request about to start.
This is suitable for any -stable kernel.
Reported-by: Ray Morris <support@bettercgi.com> Tested-by: Ray Morris <support@bettercgi.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that with recent kernel, writeback can still be happening
while shutdown is happening, and consequently data can be written
after the md reboot notifier switches all arrays to read-only.
This causes a BUG.
So don't switch them to read-only - just mark them clean and
set 'safemode' to '2' which mean that immediately after any
write the array will be switch back to 'clean'.
This could result in the shutdown happening when array is marked
dirty, thus forcing a resync on reboot. However if you reboot
without performing a "sync" first, you get to keep both halves.
This is suitable for any stable kernel (though there might be some
conflicts with obvious fixes in earlier kernels).
When commit 69e51b449d383e (md/bitmap: separate out loading a bitmap...)
created bitmap_load, it missed calling it after bitmap_create when a
bitmap is created through the sysfs interface.
So if a bitmap is added this way, we don't allocate memory properly
and can crash.
This is suitable for any -stable release since 2.6.35. Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in tcm_fc where fc_exch memory from fc_exch_mgr->ep_pool
is currently being leaked by ft_send_resp_status() usage. Following current
code in ft_queue_status() response path, using lport->tt.seq_send() needs to be
followed by a lport->tt.exch_done() in order to release fc_exch memory back into
libfc_em kmem_cache.
ft_send_resp_status() code is currently used in pre submit se_cmd ft_send_work()
error exceptions, TM request setup exceptions, and main TM response callback
path in ft_queue_tm_resp(). This bugfix addresses the leak in these cases.
Cc: Mark D Rustad <mark.d.rustad@intel.com> Cc: Kiran Patil <kiran.patil@intel.com> Cc: Robert Love <robert.w.love@intel.com> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
commit 28824b18ac4705e876a282a15ea0de8fc957551f:
|Author: Michal Nazarewicz <m.nazarewicz@samsung.com>
|Date: Wed May 5 12:53:13 2010 +0200
|
| USB: gadget: __init and __exit tags removed
|
| __init, __initdata and __exit tags have have been removed from
| various files to make it possible for gadgets that do not use
| the __init/__exit tags to use those.
obviously missed (at least) this case leading to a section mismatch in
g_ffs.c when compiling with CONFIG_USB_FUNCTIONFS_ETH enabled.
A previous commit af65cbf296 (ALSA: hdmi: fix printout of SAD sampling
rates) fixed the sample rates shown in /proc/asound/cardX/eldY and
kernel log to not be entirely wrong. However, a missing rate from the
array added in the patch causes HDMI rates 88.2 kHz, 96 kHz, 176.4 kHz,
and 192 kHz to be shown as 96 kHz, 176.4 kHz, 192 kHz, and 384 kHz,
respectively.
Fix the reporting by adding the ALSA rate 64 kHz into the conversion
array between 48 kHz and 88.2 kHz.
This patch fixes a free after use in lio_target_make_nodeacl() where
iscsi_node_acl was referenced from the original se_nacl_new allocation,
instead of from core_tpg_add_initiator_node_acl() in the case of dynamic
-> explict NodeACL conversion.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make iscsit_alloc_buffs() failure case for page_alloc_failed use correct
__free_page() SGL pointer, and return -ENOMEM for iscsit_allocate_iovecs
failure to push se_cmd->t_mem_sg release into iscsit_release_cmd()
callback during iscsit_add_reject_from_cmd() connection reset.
Also drop cmd->t_mem_sg = NULL assignment from page_alloc_failed
failure case.
Reported-by: Roland Dreier <roland@purestorage.com> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PXA's SSP engine fails to take its current channel phase into account
when enabling a stream while the engine is already running. This
results in randomly swapped left/right channels on either the record
or the playback side, depending on which one was enabled first.
The following patch fixes this by factoring out the bit field
modifications in question to a separate function that pauses the
engine temporarily, modifies the bits and kicks it off again
afterwards. Appearantly, a transition of SSCR0_SSE syncs both
directions properly.
The patch has been rolled out to quite a number of devices over the
last weeks and seems to fix the issue reliably.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WM8776 codec driver requires the machine driver to set one of the
SND_SOC_DAIFMT_CBx_xxx values. The P1022DS machine driver should be setting
SND_SOC_DAIFMT_CBM_CFM, but since that value was zero, no one noticed.
Commit 75d9ac46 ("ASoC: Allow DAI formats to be specified in the
dai_link"), however, changed the value of SND_SOC_DAIFMT_CBM_CFM from zero
to a non-zero value, which means that it now needs to be specifically set
by the machine driver.
We also set SND_SOC_DAIFMT_NB_NF, for the same reason.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking i_mutex in hugetlbfs_read() can result in deadlock with mmap as
explained below
Thread A:
read() on hugetlbfs
hugetlbfs_read() called
i_mutex grabbed
hugetlbfs_read_actor() called
__copy_to_user() called
page fault is triggered
Thread B, sharing address space with A:
mmap() the same file
->mmap_sem is grabbed on task_B->mm->mmap_sem
hugetlbfs_file_mmap() is called
attempt to grab ->i_mutex and block waiting for A to give it up
Thread A:
pagefault handled blocked on attempt to grab task_A->mm->mmap_sem,
which happens to be the same thing as task_B->mm->mmap_sem. Block waiting
for B to give it up.
AFAIU the i_mutex locking was added to hugetlbfs_read() as per
http://lkml.indiana.edu/hypermail/linux/kernel/0707.2/3066.html to take
care of the race between truncate and read. This patch fixes this by
looking at page->mapping under lock_page() (find_lock_page()) to ensure
that the inode didn't get truncated in the range during a parallel read.
Ideally we can extend the patch to make sure we don't increase i_size in
mmap. But that will break userspace, because applications will now have
to use truncate(2) to increase i_size in hugetlbfs.
This is on a system with 8TB available via the AMS pool, and as a quirk
of AMS in firmware, all of that memory shows up in node 0. So, we end
up with an allocation that will fail the goal/limit constraints.
In theory, we could "fall-back" to alloc_bootmem_node() in
sparse_early_usemaps_alloc_node(), but since we actually have HOTREMOVE
defined, we'll BUG_ON() instead. A simple solution appears to be to
unconditionally remove the limit condition in alloc_bootmem_section,
meaning allocations are allowed to cross section boundaries (necessary
for systems of this size).
Johannes Weiner pointed out that if alloc_bootmem_section() no longer
guarantees section-locality, we need check_usemap_section_nr() to print
possible cross-dependencies between node descriptors and the usemaps
allocated through it. That makes the two loops in
sparse_early_usemaps_alloc_node() identical, so re-factor the code a
bit.
[akpm@linux-foundation.org: code simplification] Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Anton Blanchard <anton@au1.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Ben Herrenschmidt <benh@kernel.crashing.org> Cc: Robert Jennings <rcj@linux.vnet.ibm.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system suspend pm_genpd_suspend_noirq() checks if the given
device is in a wakeup path (i.e. it appears to be needed for one or
more wakeup devices to work or is a wakeup device itself) and if it
needs to be "active" for wakeup to work. If that is the case, the
function returns 0 without incrementing the device domain's counter
of suspended devices and without executing genpd_stop_dev() for the
device. In consequence, the device is not stopped (e.g. its clock
isn't disabled) and power is always supplied to its domain in the
resulting system sleep state.
However, pm_genpd_resume_noirq() doesn't repeat that check and it
runs genpd_start_dev() and decrements the domain's counter of
suspended devices even for the wakeup device that weren't stopped by
pm_genpd_suspend_noirq(). As a result, the start callback may be run
unnecessarily for them and their domains' counters of suspended
devices may become negative. Both outcomes aren't desirable, so fix
pm_genpd_resume_noirq() to look for wakeup devices that might not be
stopped by during system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Simon Horman <horms@verge.net.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3321c07ae5068568cd61ac9f4ba749006a7185c9 correctly clears the TPM
buffer if the user specified read length is >= the TPM buffer length. However,
if the user specified read length is < the TPM buffer length, then part of the
TPM buffer is left uncleared.
In some cases it may happen that pmd_none_or_clear_bad() is called with
the mmap_sem hold in read mode. In those cases the huge page faults can
allocate hugepmds under pmd_none_or_clear_bad() and that can trigger a
false positive from pmd_bad() that will not like to see a pmd
materializing as trans huge.
It's not khugepaged causing the problem, khugepaged holds the mmap_sem
in write mode (and all those sites must hold the mmap_sem in read mode
to prevent pagetables to go away from under them, during code review it
seems vm86 mode on 32bit kernels requires that too unless it's
restricted to 1 thread per process or UP builds). The race is only with
the huge pagefaults that can convert a pmd_none() into a
pmd_trans_huge().
Effectively all these pmd_none_or_clear_bad() sites running with
mmap_sem in read mode are somewhat speculative with the page faults, and
the result is always undefined when they run simultaneously. This is
probably why it wasn't common to run into this. For example if the
madvise(MADV_DONTNEED) runs zap_page_range() shortly before the page
fault, the hugepage will not be zapped, if the page fault runs first it
will be zapped.
Altering pmd_bad() not to error out if it finds hugepmds won't be enough
to fix this, because zap_pmd_range would then proceed to call
zap_pte_range (which would be incorrect if the pmd become a
pmd_trans_huge()).
The simplest way to fix this is to read the pmd in the local stack
(regardless of what we read, no need of actual CPU barriers, only
compiler barrier needed), and be sure it is not changing under the code
that computes its value. Even if the real pmd is changing under the
value we hold on the stack, we don't care. If we actually end up in
zap_pte_range it means the pmd was not none already and it was not huge,
and it can't become huge from under us (khugepaged locking explained
above).
All we need is to enforce that there is no way anymore that in a code
path like below, pmd_trans_huge can be false, but pmd_none_or_clear_bad
can run into a hugepmd. The overhead of a barrier() is just a compiler
tweak and should not be measurable (I only added it for THP builds). I
don't exclude different compiler versions may have prevented the race
too by caching the value of *pmd on the stack (that hasn't been
verified, but it wouldn't be impossible considering
pmd_none_or_clear_bad, pmd_bad, pmd_trans_huge, pmd_none are all inlines
and there's no external function called in between pmd_trans_huge and
pmd_none_or_clear_bad).
if (pmd_trans_huge(*pmd)) {
if (next-addr != HPAGE_PMD_SIZE) {
VM_BUG_ON(!rwsem_is_locked(&tlb->mm->mmap_sem));
split_huge_page_pmd(vma->vm_mm, pmd);
} else if (zap_huge_pmd(tlb, vma, pmd, addr))
continue;
/* fall through */
}
if (pmd_none_or_clear_bad(pmd))
Because this race condition could be exercised without special
privileges this was reported in CVE-2012-1179.
The race was identified and fully explained by Ulrich who debugged it.
I'm quoting his accurate explanation below, for reference.
After the PMD table entry has been cleared, there is an inconsistency
between the actual number of PMD table entries that are mapping the page
and the page's map count (_mapcount field in struct page). When the page
is subsequently reclaimed, __split_huge_page() detects this inconsistency.
The root cause of the problem is a race of two threads in a multithreaded
process. Thread B incurs a page fault on a virtual address that has never
been accessed (PMD entry is zero) while Thread A is executing an madvise()
system call on a virtual address within the same 2 MB (huge page) range.
- Thread A is executing an madvise(..., MADV_DONTNEED) system call
on the virtual address range "A(range)" shown in the picture.
sys_madvise
// Acquire the semaphore in shared mode.
down_read(¤t->mm->mmap_sem)
...
madvise_vma
switch (behavior)
case MADV_DONTNEED:
madvise_dontneed
zap_page_range
unmap_vmas
unmap_page_range
zap_pud_range
zap_pmd_range
//
// Assume that this huge page has never been accessed.
// I.e. content of the PMD entry is zero (not mapped).
//
if (pmd_trans_huge(*pmd)) {
// We don't get here due to the above assumption.
}
//
// Assume that Thread B incurred a page fault and
.---------> // sneaks in here as shown below.
| //
| if (pmd_none_or_clear_bad(pmd))
| {
| if (unlikely(pmd_bad(*pmd)))
| pmd_clear_bad
| {
| pmd_ERROR
| // Log "bad pmd ..." message here.
| pmd_clear
| // Clear the page's PMD entry.
| // Thread B incremented the map count
| // in page_add_new_anon_rmap(), but
| // now the page is no longer mapped
| // by a PMD entry (-> inconsistency).
| }
| }
|
v
- Thread B is handling a page fault on virtual address "B(fault)" shown
in the picture.
...
do_page_fault
__do_page_fault
// Acquire the semaphore in shared mode.
down_read_trylock(&mm->mmap_sem)
...
handle_mm_fault
if (pmd_none(*pmd) && transparent_hugepage_enabled(vma))
// We get here due to the above assumption (PMD entry is zero).
do_huge_pmd_anonymous_page
alloc_hugepage_vma
// Allocate a new transparent huge page here.
...
__do_huge_pmd_anonymous_page
...
spin_lock(&mm->page_table_lock)
...
page_add_new_anon_rmap
// Here we increment the page's map count (starts at -1).
atomic_set(&page->_mapcount, 0)
set_pmd_at
// Here we set the page's PMD entry which will be cleared
// when Thread A calls pmd_clear_bad().
...
spin_unlock(&mm->page_table_lock)
The mmap_sem does not prevent the race because both threads are acquiring
it in shared mode (down_read). Thread B holds the page_table_lock while
the page's map count and PMD table entry are updated. However, Thread A
does not synchronize on that lock.
====== end quote =======
[akpm@linux-foundation.org: checkpatch fixes] Reported-by: Ulrich Obergfell <uobergfe@redhat.com> Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Jones <davej@redhat.com> Acked-by: Larry Woodman <lwoodman@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Cc: Mark Salter <msalter@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent changes to clear_IO_APIC_pin() which tries to
clear remoteIRR bit explicitly, some of the users started to see
"Unable to reset IRR for apic .." messages.
Close look shows that these are related to bogus IO-APIC entries
which return's all 1's for their io-apic registers. And the
above mentioned error messages are benign. But kernel should
have ignored such io-apic's in the first place.
Check if register 0, 1, 2 of the listed io-apic are all 1's and
ignore such io-apic.
Reported-by: Álvaro Castillo <midgoon@gmail.com> Tested-by: Jon Dufresne <jon@jondufresne.org> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: yinghai@kernel.org Cc: kernel-team@fedoraproject.org Cc: Josh Boyer <jwboyer@redhat.com> Link: http://lkml.kernel.org/r/1331577393.31585.94.camel@sbsiddha-desk.sc.intel.com
[ Performed minor cleanup of affected code. ] Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An iser target may send iscsi NO-OP PDUs as soon as it marks the iSER
iSCSI session as fully operative. This means that there is window
where there are no posted receive buffers on the initiator side, so
it's possible for the iSER RC connection to break because of RNR NAK /
retry errors. To fix this, rely on the flags bits in the login
request to have FFP (0x3) in the lower nibble as a marker for the
final login request, and post an initial chunk of receive buffers
before sending that login request instead of after getting the login
response.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add VF spoof check to IFLA policy. The original patch I submitted to
add the spoof checking feature to rtnl failed to add the proper policy
rule that identifies the data type and len. This patch corrects that
oversight. No bugs have been reported against this but it may cause
some problem for the netlink message parsing that uses the policy
table.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it possible to reload driver if insmod has failed due to
missing firmware.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
Fix this by disabling the alarm when there are no timers to run.
The original version of this patch was reverted. This version
disables the irq directly instead of setting a disabled timer
in the future.
Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Merged in the second revision from Rabin] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2008, commit 0c5d1eb77a8be ("genirq: record trigger type") modified the
way set_irq_type() handles the 'no trigger' condition. However, this has
an adverse effect on PCMCIA support on Intel StrongARM and probably PXA
platforms.
PCMCIA has several status signals on the socket which can trigger
interrupts; some of these status signals depend on the card's mode
(whether it is configured in memory or IO mode). For example, cards have
a 'Ready/IRQ' signal: in memory mode, this provides an indication to
PCMCIA that the card has finished its power up initialization. In IO
mode, it provides the device interrupt signal. Other status signals
switch between on-board battery status and loud speaker output.
In classical PCMCIA implementations, where you have a specific socket
controller, the controller provides a method to mask interrupts from the
socket, and importantly ignore any state transitions on the pins which
correspond with interrupts once masked. This masking prevents unwanted
events caused by the removal and application of socket power being
forwarded.
However, on platforms where there is no socket controller, the PCMCIA
status and interrupt signals are routed to standard edge-triggered GPIOs.
These GPIOs can be configured to interrupt on rising edge, falling edge,
or never. This is where the problems start.
Edge triggered interrupts are required to record events while disabled via
the usual methods of {free,request,disable,enable}_irq() to prevent
problems with dropped interrupts (eg, the 8390 driver uses disable_irq()
to defer the delivery of interrupts). As a result, these interfaces can
not be used to implement the desired behaviour.
The side effect of this is that if the 'Ready/IRQ' GPIO is disabled via
disable_irq() on suspend, and enabled via enable_irq() after resume, we
will record the state transitions caused by powering events as valid
interrupts, and foward them to the card driver, which may attempt to
access a card which is not powered up.
This leads delays resume while drivers spin in their interrupt handlers,
and complaints from drivers before they realize what's happened.
Moreover, in the case of the 'Ready/IRQ' signal, this is requested and
freed by the card driver itself; the PCMCIA core has no idea whether the
interrupt is requested, and, therefore, whether a call to disable_irq()
would be valid. (We tried this around 2.4.17 / 2.5.1 kernel era, and
ended up throwing it out because of this problem.)
Therefore, it was decided back in around 2002 to disable the edge
triggering instead, resulting in all state transitions on the GPIO being
ignored. That's what we actually need the hardware to do.
The commit above changes this behaviour; it explicitly prevents the 'no
trigger' state being selected.
The reason that request_irq() does not accept the 'no trigger' state is
for compatibility with existing drivers which do not provide their desired
triggering configuration. The set_irq_type() function is 'new' and not
used by non-trigger aware drivers.
Therefore, revert this change, and restore previously working platforms
back to their former state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: linux@arm.linux.org.uk Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The queue handling in the udev daemon assumes that the events are
ordered.
Before this patch uevent_seqnum is incremented under sequence_lock,
than an event is send uner uevent_sock_mutex. I want to say that code
contained a window between incrementing seqnum and sending an event.
This patch locks uevent_sock_mutex before incrementing uevent_seqnum.
v2: delete sequence_lock, uevent_seqnum is protected by uevent_sock_mutex
v3: unlock the mutex before the goto exit
Thanks for Kay for the comments.
Signed-off-by: Andrew Vagin <avagin@openvz.org> Tested-By: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'long secs' is passed as divisor to div_s64, which accepts a 32bit
divisor. On 64bit machines that value is trimmed back from 8 bytes
back to 4, causing a divide by zero when the number is bigger than
(1 << 32) - 1 and all 32 lower bits are 0.
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
It happens more with P2P because there we can
go between associated/unassociated frequently.
Reported-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver rtl8192ce when used with the RTL8188CE device would start at about
20 Mbps on a 54 Mbps connection, but quickly drop to 1 Mbps. One of the
symptoms is that the AP would need to retransmit each packet 4 of 5 times
before the driver would acknowledge it. Recovery is possible only by
unloading and reloading the driver. This problem was reported at
https://bugzilla.redhat.com/show_bug.cgi?id=770207.
The problem is due to a missing update of the gain setting.
Signed-off-by: Jingjun Wu <jingjun_wu@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When driver rtl8192cu is used with the debug level set to 3 or greater,
the result is "sleeping function called from invalid context" due to
an rcu_read_lock() call in the DM refresh routine in driver rtl8192c.
This lock is not necessary as the USB driver does not use the struct
being protected, thus the lock is set only when a PCI interface is
active.
This bug is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Tested-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle previous allocation failures when freeing device memory
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Mikhail Kryshen <mikhail@kryshen.net> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A MCS7820 device supports two serial ports and a MCS7840 device supports
four serial ports. Both devices use the same driver, but the attach function
in driver was unable to correctly handle the port numbers for MCS7820
device. This problem has been fixed in this patch and this fix has been
verified on x86 Linux kernel 3.2.9 with both MCS7820 and MCS7840 devices.
Signed-off-by: Donald Lee <donald@asix.com.tw> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the cp210x driver to support CP210x multiple
interface devices devices from Silicon Labs. The existing driver
always sends control requests to interface 0, which is hardcoded in
the usb_control_msg function calls. This only allows for single
interface devices to be used, and causes a bug when using ports on an
interface other than 0 in the multiple interface devices.
Here are the changes included in this patch:
- Updated the device list to contain the Silicon Labs factory default
VID/PID for multiple interface CP210x devices
- Created a cp210x_port_private struct created for each port on
startup, this struct holds the interface number
- Added a cp210x_release function to clean up the cp210x_port_private
memory created on startup
- Modified usb_get_config and usb_set_config to get a pointer to the
cp210x_port_private struct, and use the interface number there in the
usb_control_message wIndex param
Signed-off-by: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gobi 1000 devices have a different port layout, which wasn't respected
by the current driver, and thus it grabbed the QMI/net port. In the
near future we'll be attaching another driver to the QMI/net port for
these devices (cdc-wdm and qmi_wwan) so make sure the qcserial driver
doesn't claim them. This patch also prevents qcserial from binding to
interfaces 0 and 1 on 1K devices because those interfaces do not
respond.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__do_config_autodelink passes the data variable to the transport function.
If the calling functions pass a stack variable, this will eventually trigger
a DMA-API debug backtrace for mapping stack memory in the DMA buffer. Fix
this by calling kmemdup for the passed data instead.
When build i.mx platform with imx_v6_v7_defconfig, and after adding
USB Gadget support, it has below build error:
CC drivers/usb/host/fsl-mph-dr-of.o
drivers/usb/host/fsl-mph-dr-of.c: In function 'fsl_usb2_device_register':
drivers/usb/host/fsl-mph-dr-of.c:97: error: 'struct pdev_archdata'
has no member named 'dma_mask'
It has discussed at: http://www.spinics.net/lists/linux-usb/msg57302.html
For PowerPC, there is dma_mask at struct pdev_archdata, but there is
no dma_mask at struct pdev_archdata for ARM. The pdev_archdata is
related to specific platform, it should NOT be accessed by
cross platform drivers, like USB.
The code for pdev_archdata should be useless, as for PowerPC,
it has already gotten the value for pdev->dev.dma_mask at function
arch_setup_pdev_archdata of arch/powerpc/kernel/setup-common.c.
The reason of above dump message is calling dma_poll_alloc with can-schedule
mem_flags at atomic context.
To fix this problem, below changes are made:
- fsl_req_to_dtd doesn't need to be protected by spin_lock_irqsave,
as struct usb_request can be access at process context. Move lock
to beginning of hardware visit (fsl_queue_td).
- Change the memory flag which using to allocate dTD descriptor buffer,
the memory flag can be from gadget layer.
It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must not allow the input buffer length to change while we're
shuffling the buffer contents. We also mustn't clear the WDM_READ
flag after more data might have arrived. Therefore move both of these
into the spinlocked region at the bottom of wdm_read().
When reading desc->length without holding the iuspin lock, use
ACCESS_ONCE() to ensure the compiler doesn't re-read it with
inconsistent results.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Bjørn Mork <bjorn@mork.no> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unicode font map for the virtual console is a 32x32x64 table which
allocates rows dynamically as entries are added. The unicode value
increases sequentially and should count all entries even in empty
rows. The defect is when copying the unicode font map in con_set_unimap(),
the unicode value is not incremented properly. The wrong unicode value
is entered in the new font map.
Signed-off-by: Liz Clark <liz.clark@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is supposed to be doing a shift before the comparison instead of
just doing a bitwise AND directly. The current code means the start()
just returns without doing anything.
This patch fixies follwing two memory leak patterns that reported by kmemleak.
sysfs_sd_setsecdata() is called during sys_lsetxattr() operation.
It checks sd->s_iattr is NULL or not. Then if it is NULL, it calls
sysfs_init_inode_attrs() to allocate memory.
That code is this.
iattrs = sd->s_iattr;
if (!iattrs)
iattrs = sysfs_init_inode_attrs(sd);
The iattrs recieves sysfs_init_inode_attrs()'s result, but sd->s_iattr
doesn't know the address. so it needs to set correct address to
sd->s_iattr to free memory in other function.
Some of the newer futex PI opcodes do not check the cmpxchg enabled
variable and call unconditionally into the handling functions. Cover
all PI opcodes in a separate check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HID devices should specify this in their interface descriptors, not in the
device descriptor. This fixes a "missing hardware id" bug under Windows 7 with
a VIA VL800 (3.0) controller.
A read from GadgetFS endpoint 0 during the data stage of a control
request would always return 0 on success (as returned by
wait_event_interruptible) despite having written data into the user
buffer.
This patch makes it correctly set the return value to the number of
bytes read.
Signed-off-by: Thomas Faber <thfabba@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixup below warning on device_unregister()
renesas_usbhs renesas_usbhs.1: host probed
renesas_usbhs renesas_usbhs.1: gadget probed
renesas_usbhs renesas_usbhs.1: irq request err
------------[ cut here ]------------
WARNING: at ${LINUX}/drivers/base/core.c:1)
Device 'gadget' does not have a release() function, it is broken and must be fi.
Modules linked in:
[<c000e25c>] (unwind_backtrace+0x0/0xe4) from [<c0016960>] (warn_slowpath_commo)
[<c0016960>] (warn_slowpath_common+0x4c/0x64) from [<c00169f8>] (warn_slowpath_)
[<c00169f8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0185b80>] (device_release+0x)
[<c0185b80>] (device_release+0x70/0x84) from [<c013e300>] (kobject_cleanup+0x58)
[<c013e300>] (kobject_cleanup+0x58/0x6c) from [<c01cba14>] (usbhs_mod_gadget_re)
[<c01cba14>] (usbhs_mod_gadget_remove+0x3c/0x6c) from [<c01c8384>] (usbhs_mod_p)
[<c01c8384>] (usbhs_mod_probe+0x68/0x80) from [<c01c7f84>] (usbhs_probe+0x1cc/0)
...
musb INDEX register is getting modified/corrupted during temporary
un-locking in a SMP system. Set this register with proper value
after re-acquiring the lock
Scenario:
---------
CPU1 is handling a data transfer completion interrupt received for
the CLASS1 EP
CPU2 is handling a CLASS2 thread which is queuing data to musb for
transfer
Below is the error sequence:
CPU1 | CPU2
--------------------------------------------------------------------
Data transfer completion inter- |
rupt recieved. |
|
musb INDEX reg set to CLASS1 EP |
|
musb LOCK is acquired. |
|
| CLASS2 thread queues data.
|
| CLASS2 thread tries to acquire musb
| LOCK but lock is already taken by
| CLASS1, so CLASS2 thread is
| spinning.
|
From Interrupt Context musb |
giveback function is called |
|
The giveback function releases | CLASS2 thread now acquires LOCK
LOCK |
|
ClASS1 Request's completion cal-| ClASS2 schedules the data transfer and
lback is called | sets the MUSB INDEX to Class2 EP number
|
Interrupt handler for CLASS1 EP |
tries to acquire LOCK and is |
spinning |
|
Interrupt for Class1 EP acquires| Class2 completes the scheduling etc and
the MUSB LOCK | releases the musb LOCK
|
Interrupt for Class1 EP schedul-|
es the next data transfer |
but musb INDEX register is still|
set to CLASS2 EP |
Since the MUSB INDEX register is set to a different endpoint, we
read and modify the wrong registers. Hence data transfer will not
happen properly. This results in unpredictable behavior
So, the MUSB INDEX register is set to proper value again when
interrupt re-acquires the lock
In commit c6dc001 "staging: r8712u: Merging Realtek's latest (v2.6.6).
Various fixes", the returned qual.qual member of the iw_statistics
struct was changed. For strong signals, this change made no difference;
however for medium and weak signals it results in a low signal that
shows considerable fluctuation, When using wicd for a medium-strength
AP, the value reported in the status line is reduced from 100% to 60% by
this bug.
This problem is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42826.
Reported-and-tested-by: Robert Crawford <wrc1944@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a5ee652 "staging: r8712u: Interface-state not fully tracked",
the private boolean "bup" was set false when the interface was brought down,
as that seemed appropriate. This change has not caused any problems when
using NetworkManager or manual control of the device; however, when wicd
control is used, there is a locking problem in wpa_supplicant, as shown in
https://bugzilla.kernel.org/show_bug.cgi?id=42818.
This fix reverts the only code change in commit a5ee652. My
analysis is that "bup" is badly named. In its present form, it
seems to indicate the up/down state of the device, but its usage
is more consistent with an initialized/uninitialized state. That
problem will be addressed in a later patch.
Note: Commit 8c213fa, which introdued asynchronous firmware loading
for this driver, exposed this bug to a greater extent. That bug
is addressed in the next patch in this series.
This bug is also responsible for the bug in
https://bugzilla.kernel.org/show_bug.cgi?id=42815. and this bug is
also part of the problems discussed at https://bugs.archlinux.org/task/27996#comment89950.
Tested-by: Alberto Lago Ballesteros <saniukeokusainaya@gmail.com> Tested-by: Adrian <agib@gmx.de> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this driver was upgraded to the vendor 20100831 version in
commit 93c55dda092c7 et al,, one listhead initialization was missed.
This broke complete operation of the driver whenever AP mode was
enabled. This fixes https://bugs.archlinux.org/task/27996.
The configuration parameter R8712_AP is misleading as the driver cannot
function as an AP without a heavily hacked version of hostapd. Thus, it
makes sense to remove the parameter; however the code and data configured
for the option is left in.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PID 0x6015, corresponding to the new series of FT-X chips
(FT220XD, FT201X, FT220X, FT221X, FT230X, FT231X, FT240X). They all
appear as serial devices, and seem indistinguishable except for the
default product string stored in their EEPROM. The baudrate
generation matches FT232RL devices.
Tested with a FT201X and FT230X at various baudrates (100 - 3000000).
Sample dmesg:
ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
usb 2-1: new full-speed USB device number 6 using ohci_hcd
usb 2-1: New USB device found, idVendor=0403, idProduct=6015
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: FT230X USB Half UART
usb 2-1: Manufacturer: FTDI
usb 2-1: SerialNumber: DC001WI6
ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
drivers/usb/serial/ftdi_sio.c: ftdi_sio_port_probe
drivers/usb/serial/ftdi_sio.c: ftdi_determine_type: bcdDevice = 0x1000, bNumInterfaces = 1
usb 2-1: Detected FT-X
usb 2-1: Number of endpoints 2
usb 2-1: Endpoint 1 MaxPacketSize 64
usb 2-1: Endpoint 2 MaxPacketSize 64
usb 2-1: Setting MaxPacketSize 64
drivers/usb/serial/ftdi_sio.c: read_latency_timer
drivers/usb/serial/ftdi_sio.c: write_latency_timer: setting latency timer = 1
drivers/usb/serial/ftdi_sio.c: create_sysfs_attrs
drivers/usb/serial/ftdi_sio.c: sysfs attributes for FT-X
usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
Signed-off-by: Jim Paris <jim@jtan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life
easier for Windows users, so we need a similar workaround as the Calao
board to support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some misconfigured ftdi_sio devices, if the manufacturer string is
NULL, the kernel will oops when the device is plugged in. This patch
fixes the problem.
Reported-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl> Tested-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device presents a total of 5 interfaces with ff/ff/ff
class/subclass/protocol. The last one of these is verified
to be a QMI/wwan combined interface which should be handled
by the qmi_wwan driver, so we blacklist it here.
commit 0d905fd "USB: option: convert Huawei K3765, K4505, K4605
reservered interface to blacklist" accidentally ANDed two
blacklist tests by leaving out a return. This was not noticed
because the two consecutive bracketless if statements made it
syntactically correct.
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com> Reported-by: Adam Conrad <adconrad@ubuntu.com> Tested-by: Adam Conrad <adconrad@ubuntu.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't
need to dev_hold().
With dev_hold(), not corresponding dev_put(), will lead to leak.
[ bug introduced in 96b52e61be1 (ipv6: mcast: RCU conversions) ]
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea4fc0d619 (ipv4: Don't use rt->rt_{src,dst} in ip_queue_xmit())
added a serious regression on synflood handling.
Simon Kirby discovered a successful connection was delayed by 20 seconds
before being responsive.
In my tests, I discovered that xmit frames were lost, and needed ~4
retransmits and a socket dst rebuild before being really sent.
In case of syncookie initiated connection, we use a different path to
initialize the socket dst, and inet->cork.fl.u.ip4 is left cleared.
As ip_queue_xmit() now depends on inet flow being setup, fix this by
copying the temp flowi4 we use in cookie_v4_check().
Reported-by: Simon Kirby <sim@netnation.com> Bisected-by: Simon Kirby <sim@netnation.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately this is not how snprintf works. snprintf returns the
number of characters that would have been written if there was enough
space. In the above case, if the first snprintf returns a value larger
than size, we pass a negative size into the second snprintf and happily
scribble over the stack. If you have 3000 character c++ methods thats a
lot of stack to trample.
This patch fixes repsep_snprintf by clamping the value at size - 1 which
is the maximum snprintf can write before adding the NULL terminator.
I get the sinking feeling that there are a lot of other uses of snprintf
that have this same bug, we should audit them all.
Cc: David Ahern <dsahern@gmail.com> Cc: Eric B Munson <emunson@mgebm.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com> Link: http://lkml.kernel.org/r/20120307114249.44275ca3@kryten Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the report from Slicky Devil, nilfs caused kernel oops at
nilfs_load_super_block function during mount after he shrank the
partition without resizing the filesystem:
Intersil reports that all chips supported by the zl6100 driver require
an interval between chip accesses, even ZL2004 and ZL6105 which were thought
to be safe.
This patch addresses a bug with target_check_scsi2_reservation_conflict()
return checking in target_scsi2_reservation_[reserve,release]() that was
preventing CRH=1 operation from silently succeeding in the two special
cases defined by SPC-3, and not failing with reservation conflict status
when dealing with legacy RESERVE/RELEASE + active SPC-3 PR logic.
Also explictly set cmd->scsi_status = SAM_STAT_RESERVATION_CONFLICT during
the early non reservation holder failure from pr_ops->t10_seq_non_holder()
check in transport_generic_cmd_sequencer() for fabrics that already expect
it to be set.
This bug was originally introduced in mainline commit:
Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a iscsi-target specific bug related to reservation conflict
handling in iscsit_handle_scsi_cmd() that has been causing reservation conflicts
to complete and not fail as expected due to incorrect errno checking. The problem
occured with the change to return -EBUSY from transport_generic_cmd_sequencer() ->
transport_generic_allocate_tasks() failures, that broke iscsit_handle_scsi_cmd()
checking for -EINVAL in order to invoke a non GOOD status response.
This was manifesting itself as data corruption with legacy SPC-2 reservations,
but also effects iscsi-target LUNs with SPC-3 persistent reservations.
This bug was originally introduced in lio-core commit:
Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.
To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix indexed register offset definitions that use decimal (wrong) instead
of hexadecimal (correct) notation for indexing multipliers.
Incorrect definitions do not affect Tsi721 driver in its current default
configuration because it uses only IDB queue 0. Loss of inbound
doorbell functionality should be observed if queue other than 0 is used.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Chul Kim <chul.kim@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly set the source of temp2 for the W83627UHG. Also fix a
comment right before that, and document the W83627UHG as reporting up
to 3 temperatures.
NCT6775F and NCT6776F have their own set of registers for FAN_STOP_TIME. The
correct registers were used to read FAN_STOP_TIME, but writes used the wrong
registers. Fix it.
Newer version of binutils are more strict about specifying the
correct options to enable certain classes of instructions.
The sparc32 build is done for v7 in order to support sun4c systems
which lack hardware integer multiply and divide instructions.
So we have to pass -Av8 when building the assembler routines that
use these instructions and get patched into the kernel when we find
out that we have a v8 capable cpu.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1519) fixes a bug in the block layer's disk-events
polling. The polling is done by a work routine queued on the
system_nrt_wq workqueue. Since that workqueue isn't freezable, the
polling continues even in the middle of a system sleep transition.
Obviously, polling a suspended drive for media changes and such isn't
a good thing to do; in the case of USB mass-storage devices it can
lead to real problems requiring device resets and even re-enumeration.
The patch fixes things by creating a new system-wide, non-reentrant,
freezable workqueue and using it for disk-events polling.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Tejun Heo <tj@kernel.org> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Then we unblock events, when they are suppose to be blocked. This can
trigger events related block/genhd.c warnings, but also can crash in
sd_check_events() or other places.
I'm able to reproduce crashes with the following scripts (with
connected usb dongle as sdb disk).
function stop_me()
{
for i in `jobs -p` ; do kill $i 2> /dev/null ; done
exit
}
trap stop_me SIGHUP SIGINT SIGTERM
for ((i = 0; i < 10; i++)) ; do
while true; do fdisk -l $DEV 2>&1 > /dev/null ; done &
done
while true ; do
echo 1 > $ENABLE
sleep 1
echo 0 > $ENABLE
done
</snip>
I use the script to verify patch fixing oops in sd_revalidate_disk
http://marc.info/?l=linux-scsi&m=132935572512352&w=2
Without Jun'ichi Nomura patch titled "Fix NULL pointer dereference in
sd_revalidate_disk" or this one, script easily crash kernel within
a few seconds. With both patches applied I do not observe crash.
Unfortunately after some time (dozen of minutes), script will hung in:
As drawback, I do not teardown on sysfs file create error, because I do
not know how to nullify disk->ev (since it can be used). However add_disk
error handling practically does not exist too, and things will work
without this sysfs file, except events will not be exported to user
space.
Since 2.6.39 (1196f8b), when a driver returns -ENOMEDIUM for open(),
__blkdev_get() calls rescan_partitions() to remove
in-kernel partition structures and raise KOBJ_CHANGE uevent.
However it ends up calling driver's revalidate_disk without open
and could cause oops.
In the case of SCSI:
process A process B
----------------------------------------------
sys_open
__blkdev_get
sd_open
returns -ENOMEDIUM
scsi_remove_device
<scsi_device torn down>
rescan_partitions
sd_revalidate_disk
<oops>
Oopses are reported here:
http://marc.info/?l=linux-scsi&m=132388619710052
This patch separates the partition invalidation from rescan_partitions()
and use it for -ENOMEDIUM case.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When forwarding was set and a new net device is register,
we need add this device to the all-router mcast group.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.
This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).
Since 2008 (832d11c5cd076abc0aa1eaf7be96c81d1a59ce41)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.
Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.
Before the fixes in commits cc9a672ee522d4805495b98680f4a3db5d0a0af9
and daef52bab1fd26e24e8e9578f8fb33ba1d0cb412, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.
After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:
(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
then shifts a prefix of that skb that is below snd_una
(2) tcp_shifted_skb() increments the packet count of the
already-SACKed prev sk_buff
(3) tcp_sacktag_one() sees the end of the new SACKed range is below
snd_una, so it short-circuits and doesn't increase tp->sacked_out
(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
decrements tp->sacked_out by this "inflated" pcount that was
missing a matching increase in tp->sacked_out, and hence
tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
to s32 is negative.
(6) this leads to the warnings seen in the recent "WARNING: at
net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
tcp_input.c:3418 WARN_ON((int)tp->sacked_out < 0);
More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.
This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log