iio: imu: inv_mpu6050: fix lock issues by using our own mutex
There are several locks issues when using buffer and direct polling
data at the same time. Use our own mutex for managing locking and
block simultaneous use of buffer and direct polling by using
iio_device_{claim/release}_direct_mode. This makes chip_config
enable bit obsolete, so delete it.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: imu: st_lsm6dsx: support active-low interrupts
Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Andy Shevchenko [Fri, 9 Jun 2017 12:08:10 +0000 (15:08 +0300)]
iio: adc: ad7791: Use sysfs_match_string() helper
Use sysfs_match_string() helper instead of open coded variant.
Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: adc: twl4030: Fold twl4030-madc.h into driver
twl4030-madc.h is no longer used by anything outside of
the iio driver, so it can be merged into the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This functionality is not used by the IIO subsystem. Due
to removal of legacy API it can also be removed.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: adc: twl4030: Drop struct twl4030_madc_user_parms
This struct is no longer used by anything in the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All madc users have been converted to IIO API, so drop the
legacy API. The function is still used inside of the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: adc: twl4030: Drop twl4030_get_madc_conversion()
Drop legacy twl4030_get_madc_conversion() method. It has been
used by drivers to get madc data before it conversion to IIO
API. There are no users in the mainline kernel anymore.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier [Mon, 29 May 2017 09:28:20 +0000 (11:28 +0200)]
iio: adc: stm32: add support for STM32H7
Add support for STM32H7 Analog to Digital Converter. It has up
to 20 external channels, resolution ranges from 8 to 16bits.
Either bus or asynchronous adc clock may be used.
Add registers & bitfields definition. Also add new configuration
options to enter/exit powerdown and perform self-calibration.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier [Mon, 29 May 2017 09:28:19 +0000 (11:28 +0200)]
iio: adc: stm32: make per instance bus clock optional
STM32F4 requires one clock per ADC instance for register access. But,
newer version of ADC hardware block have common bus clock for all
instances (per instance driver isn't responsible for getting it).
So, make it optional by default. Still, enforce it's required on STM32F4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier [Mon, 29 May 2017 09:28:18 +0000 (11:28 +0200)]
iio: adc: stm32: introduce compatible data cfg
Prepare support for stm32h7 adc variant by introducing compatible
configuration data.
Move STM32F4 specific stuff to compatible data structure:
- registers & bit fields
- input channels data
- start/stop procedures
- trigger definitions
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier [Mon, 29 May 2017 09:28:17 +0000 (11:28 +0200)]
iio: adc: stm32: make core adc clock optional by default
Analog clock input is mandatory on stm32f4. But newer version of
ADC hardware block allow to select either bus clock or asynchronous
clock, for analog circuitry.
So, make it optional by default, but enforce clk presence on stm32f4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier [Mon, 29 May 2017 09:28:16 +0000 (11:28 +0200)]
dt-bindings: iio: stm32-adc: add support for STM32H7
Document support for STM32H7 Analog to Digital Converter.
Main difference is regarding compatible, clock definitions and new
features like differential channels support:
STM32H7 ADC block has two clock inputs, common clock for all ADCs.
One 'bus' clock for registers access, and one optional 'adc' clock
for analog circuitry (bus clock may be used for conversions).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Stefan Brüns [Wed, 24 May 2017 00:09:06 +0000 (02:09 +0200)]
iio: adc: Fix integration time/averaging for INA219/220
INA226/230/231 has integration times per voltage channel and common
averaging setting for both channels, while the INA219/220 only has a
combined integration time/averaging setting per channel.
Only expose the averaging attribute for the INA226, and expose the correct
integration times for the INA219.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Paolo Cretaro [Sun, 28 May 2017 11:24:38 +0000 (13:24 +0200)]
iio: adc: meson-saradc: use NULL instead of 0 for pointer
Fix sparse warning: Using plain integer as NULL pointer
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Paolo Cretaro [Wed, 31 May 2017 23:50:55 +0000 (01:50 +0200)]
iio: adc: mxs-lradc: fix non-static symbol warnings
Fix sparse warning "symbol foo was not declared. Should it be static?"
for the following symbols:
mx23_lradc_adc_irq_names
mx28_lradc_adc_irq_names
iio_dev_attr_in_voltage0_scale_available
iio_dev_attr_in_voltage1_scale_available
iio_dev_attr_in_voltage2_scale_available
iio_dev_attr_in_voltage3_scale_available
iio_dev_attr_in_voltage4_scale_available
iio_dev_attr_in_voltage5_scale_available
iio_dev_attr_in_voltage6_scale_available
iio_dev_attr_in_voltage7_scale_available
iio_dev_attr_in_voltage10_scale_available
iio_dev_attr_in_voltage11_scale_available
iio_dev_attr_in_voltage12_scale_available
iio_dev_attr_in_voltage13_scale_available
iio_dev_attr_in_voltage14_scale_available
iio_dev_attr_in_voltage15_scale_available
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Stefan Brüns [Wed, 24 May 2017 00:09:05 +0000 (02:09 +0200)]
iio: adc: ina2xx: Make use of attribute flags consistent on all channels
Flags for shared channel attributes should be set on all channels of a
channel set. I.e. SAMP_FREQUENCY and OVERSAMPLING_RATIO are set on the
in_voltage{0,1} channels, thus should be set on in_power, in_current.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio: hi8435: remote ampersands from hi8435_info definition
C syntax allows apersands when initializing structures fields with
function pointers, but in Linux sources ampersands are normally not used
in thix context.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tony Lindgren [Tue, 23 May 2017 00:51:46 +0000 (17:51 -0700)]
iio: adc: cpcap: Remove hung interrupt quirk
This is no longer needed as the real problem was interrupt flags
not getting passed properly from device tree to the cpcap-core.c
mfd driver. This got fixed with commit ac89473213c6 ("mfd: cpcap:
Fix interrupt to use level interrupt") So let's remove ADC
interrupt specific the quirk.
Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tony Lindgren [Tue, 23 May 2017 00:51:45 +0000 (17:51 -0700)]
iio: adc: cpcap: Fix die temperature
It seems that "MC13783 Power Management and Audio Ciruit User's Guide"
MC1378UG.pdf documents several similar components as in the CPCAP PMIC.
Chapter "9.5.5 Die Temperature and UID" says that the die temperature
value is 282 at 25C with LSB of -1.14C. Converting CPCAP PMIC channel3
values with following seems to produce values that make sense for a
PMIC die:
temperature = 25000 + ((regval - 282) * 114)
As we don't have any other documentation, let's assume the die
temperature is unconfigured in the Motorola mapphone Linux kernel
and the current temperature conversion table should be only used
for the battery thermistor and not for the die temperature.
Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tony Lindgren [Tue, 23 May 2017 00:51:44 +0000 (17:51 -0700)]
iio: adc: cpcap: Fix default register values and battery temperature
Looking at the register dumps from Android kernel on droid 4, I noticed
the values with the mainline kernel don't match. Let's fix this by
initializing the ADC registers to what Android does.
For getting correct values from the battery thermistor, we need to
toggle the CPCAP_BIT_THERMBIAS_EN when measuring battery temperature
to get correct battery temperatures. And looks like we also need to
wait a little bit before reading the battery temperature as otherwise
the results are inaccurate.
Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Stefan Wahren [Thu, 25 May 2017 22:26:24 +0000 (00:26 +0200)]
staging: vchiq_core: Don't BUG if process is unexpected
Bail out properly if the process index doesn't match the remote insert.
We also drop the BUG in case the process index is at local insert,
so we can trigger the WARN_ON again some steps later.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Wahren [Thu, 25 May 2017 22:26:19 +0000 (00:26 +0200)]
staging: vchiq_core: Simplify VCHIQ init
Since the ARM side of VCHIQ support only 1 state, we could simplify
the init code. This makes it possible to avoid BUG_ON and a theoretical
overflow of id.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ioana Radulescu [Wed, 24 May 2017 12:13:28 +0000 (07:13 -0500)]
staging: fsl-dpaa2/eth: Map Tx buffers as bidirectional
WRIOP hardware may need to write to the hardware annotation
area of Tx buffers (e.g. frame status bits) and also to
the data area (e.g. L4 checksum in frame header).
Map these buffers as DMA_BIDIRECTIONAL, otherwise the
write transaction through SMMU will not be allowed.
Ioana Radulescu [Wed, 24 May 2017 12:13:27 +0000 (07:13 -0500)]
staging: fsl-dpaa2/eth: Fix address translations
Use the correct mechanisms for translating a DMA-mapped IOVA
address into a virtual one. Without this fix, once SMMU is
enabled on Layerscape platforms, the Ethernet driver throws
IOMMU translation faults.
Nikola Jelic [Tue, 23 May 2017 21:02:45 +0000 (23:02 +0200)]
staging: wlan-ng: hfa384x: fix several type issues.
There were several in-place conversions of 16 and 32-bit data, which caused
sparse to detect them. Changed them to the in situ versions, such as:
le16_to_cpu -> le16_to_cpus
Signed-off-by: Nikola Jelic <nikola.jelic83@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
Aliza Minkov [Thu, 25 May 2017 13:46:45 +0000 (16:46 +0300)]
dgnc: fix multiple blank lines coding style problem
According to the coding-style documentation, functions in source files
should be separated with one blank line. Redundant blank lines were
removed from this source file, in accordance with coding-style
documentation.
staging: unisys: include: renamed structure spar_io_channel_protocol in iochannel.h to match driver namespace
Renamed structure spar_io_channel_protocol to visor_io_channel and
changed "visor bus" to "visorbus" in a comment in visornic_main.c
and visorhba_main.c.
staging: unisys: include: renamed #defines in iochannel.h to match driver namespace
Renamed #defines
* ULTRA_VHBA_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_VHBA_CHANNEL_SIGNATURE
* ULTRA_VNIC_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_VNIC_CHANNEL_SIGNATURE
* ULTRA_VSWITCH_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_VSWITCH_CHANNEL_SIGNATURE
* ULTRA_VHBA_CHANNEL_PROTOCOL_VERSIONID to
VISOR_VHBA_CHANNEL_VERSIONID
* ULTRA_VNIC_CHANNEL_PROTOCOL_VERSIONID to
VISOR_VNIC_CHANNEL_VERSIONID
* ULTRA_VSWITCH_CHANNEL_PROTOCOL_VERSIONID to
VISOR_VSWITCH_CHANNEL_VERSIONID
* SPAR_VHBA_CHANNEL_OK_CLIENT to VISOR_VHBA_CHANNEL_OK_CLIENT
* SPAR_VNIC_CHANNEL_OK_CLIENT to VISOR_VNIC_CHANNEL_OK_CLIENT
staging: unisys: include: renamed #defines in channel.h to match driver namespace
Renamed #defines
* ULTRA_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_CHANNEL_SIGNATURE
* SPAR_CHANNEL_SERVER_READY to
VISOR_CHANNEL_SERVER_READY
* ULTRA_VALID_CHANNELCLI_TRANSITION
VISOR_VALID_CHANNELCLI_TRANSITION
* ULTRA_CLIERRORBOOT_THROTTLEMSG_DISABLED to
VISOR_CLIERRORBOOT_THROTTLEMSG_DISABLED
* ULTRA_CLIERRORBOOT_THROTTLEMSG_NOTATTACHED to
VISOR_CLIERRORBOOT_THROTTLEMSG_NOTATTACHED
* ULTRA_CLIERRORBOOT_THROTTLEMSG_BUSY to
VISOR_CLIERRORBOOT_THROTTLEMSG_BUSY
* ULTRA_IO_DRIVER_ENABLES_INTS to
VISOR_DRIVER_ENABLES_INTS
* ULTRA_IO_CHANNEL_IS_POLLING to
VISOR_CHANNEL_IS_POLLING
* ULTRA_IO_IOVM_IS_OK_WITH_DRIVER_DISABLING_INTS to
VISOR_IOVM_OK_DRIVER_DISABLING_INTS
* ULTRA_IO_DRIVER_DISABLES_INTS to
VISOR_DRIVER_DISABLES_INTS
* ULTRA_IO_DRIVER_SUPPORTS_ENHANCED_RCVBUF_CHECKING to
VISOR_DRIVER_ENHANCED_RCVBUF_CHECKING
* ULTRA_CHANNEL_ENABLE_INTS to
VISOR_CHANNEL_ENABLE_INTS
* SPAR_VHBA_CHANNEL_PROTOCOL_UUID to VISOR_VHBA_CHANNEL_UUID
* SPAR_VHBA_CHANNEL_PROTOCOL_UUID_STR to
VISOR_VHBA_CHANNEL_UUID_STR
* SPAR_VNIC_CHANNEL_PROTOCOL_UUID to VISOR_VNIC_CHANNEL_UUID
* SPAR_VNIC_CHANNEL_PROTOCOL_UUID_STR to
VISOR_VNIC_CHANNEL_UUID_STR
* SPAR_SIOVM_UUID to VISOR_SIOVM_UUID
staging: unisys: visorinput: renamed #defines in visorinput.c to match driver namespace
Renamed #defines
* SPAR_KEYBOARD_CHANNEL_PROTOCOL_UUID to
VISOR_KEYBOARD_CHANNEL_UUID
* SPAR_KEYBOARD_CHANNEL_PROTOCOL_UUID_STR to
VISOR_KEYBOARD_CHANNEL_UUID_STR
* SPAR_MOUSE_CHANNEL_PROTOCOL_UUID to
VISOR_MOUSE_CHANNEL_UUID
* SPAR_MOUSE_CHANNEL_PROTOCOL_UUID_STR to
VISOR_MOUSE_CHANNEL_UUID_STR
staging: unisys: visorbus: renamed enum in controlvmchannel.h to match driver namespace
Renamed enum and its members
* ultra_chipset_feature to visor_chipset_feature
* ULTRA_CHIPSET_FEATURE_REPLY to VISOR_CHIPSET_FEATURE_REPLY
* ULTRA_CHIPSET_FEATURE_PARA_HOTPLUG to
VISOR_CHIPSET_FEATURE_PARA_HOTPLUG
staging: unisys: visorbus: renamed structures in controlvmchannel.h to match driver namespace
Renamed structures
* spar_segment_state to visor_segment_state
* efi_spar_indication to efi_visor_indication
* spar_controlvm_channel_protocol to visor_controlvm_channel
* spar_controlvm_parameters_header to
visor_controlvm_parameters_header
staging: unisys: visorbus: renamed #defines in controlvmchannel.h to match driver namespace
Renamed #defines
* SPAR_CONTROLVM_CHANNEL_PROTOCOL_UUID to
VISOR_CONTROLVM_CHANNEL_UUID
* ULTRA_CONTROLVM_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_CONTROLVM_CHANNEL_SIGNATURE
* ULTRA_CONTROLVM_CHANNEL_PROTOCOL_VERSIONID to
VISOR_CONTROLVM_CHANNEL_VERSIONID
* SPAR_CONTROLVM_CHANNEL_OK_CLIENT to
VISOR_CONTROLVM_CHANNEL_OK_CLIENT
staging: unisys: visorbus: renamed #defines in visorchipset.c to match driver namespace
Renamed #defines
* UNISYS_SPAR_LEAF_ID to UNISYS_VISOR_LEAF_ID
* UNISYS_SPAR_ID_EBX to UNISYS_VISOR_ID_EBX
* UNISYS_SPAR_ID_ECX to UNISYS_VISOR_ID_ECX
* UNISYS_SPAR_ID_EDX to UNISYS_VISOR_ID_EDX
staging: unisys: visorbus: renamed structures in vbuschannel.h to match driver namespace
Renamed structures
* ultra_vbus_deviceinfo to visor_vbus_deviceinfo
* spar_vbus_headerinfo to visor_vbus_headerinfo
* spar_vbus_channel_protocol to visor_vbus_channel
staging: unisys: visorbus: renamed #defines in vbuschannel.h to match driver namespace
Renamed #defines:
* SPAR_VBUS_CHANNEL_PROTOCOL_UUID to VISOR_VBUS_CHANNEL_UUID
* SPAR_VBUS_CHANNEL_PROTOCOL_SIGNATURE to
VISOR_VBUS_CHANNEL_SIGNATURE
* SPAR_VBUS_CHANNEL_PROTOCOL_VERSIONID to
VISOR_VBUS_CHANNEL_VERSIONID
staging: unisys: visorbus: renamed functions like my_device_* to match driver namespace
Renamed functions
* my_device_create() to visorbus_device_create()
* my_device_changestate() to visorbus_device_changestate()
* my_device_destroy() to visorbus_device_destroy()
staging: unisys: visorbus: renamed functions like chipset_device_* to match driver namespace
Renamed functions
* chipset_device_create() to visorchipset_device_create()
* chipset_device_destroy() to visorchipset_device_destroy()
* chipset_device_pause() to visorchipset_device_pause()
* chipset_device_resume() to visorchipset_device_resume()
projects / karo-tx-linux.git / log