The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.
This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation".
Signed-off-by: Michael Spang <spang@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec section 4.6.1.1 and section 4.6.1.2,
after aborting a command on the command ring, xHC will
generate a command completion event with its completion
code set to Command Ring Stopped at least. If a command is
currently executing at the time of aborting a command, xHC
also generate a command completion event with its completion
code set to Command Abort. When the command ring is stopped,
software may remove, add, or rearrage Command Descriptors.
To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci. When the command ring is stopped,
software will find the command trbs described by command
descriptors in cancel_cmd_list and modify it to No Op
command. If software can't find the matched trbs, we can
think it had been finished.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8b68ab81f4c83097d3063d43ec73bb8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch is used to cancel command when the command isn't
acknowledged and a timeout occurs.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8b68ab81f4c83097d3063d43ec73bb8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.
To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.
Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8b68ab81f4c83097d3063d43ec73bb8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding cmd_ring_state for command ring. It helps to verify
the current command ring state for controlling the command
ring operations.
This patch should be backported to kernels as old as 3.0. The commit 7ed603ecf8b68ab81f4c83097d3063d43ec73bb8 "xhci: Add an assertion to
check for virt_dev=0 bug." papers over the NULL pointer dereference that
I now believe is related to a timed out Set Address command. This (and
the four patches that follow it) contain the real fix that also allows
VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug
stress tests.
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB. This causes
the host controller to place an event on the event ring, but not send an
interrupt. When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.
However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated. This means URBs stop completing, and the
USB device disconnect is not noticed. Something like a USB headset will
cause mplayer to hang when the device is disconnected.
If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.
The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.
Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the EFI variable attributes are missing from print out from
/sys/firmware/efi/vars/*/attributes. This patch adds those in. It also
updates code to use pre-defined constants for masking current value
of attributes.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is fixed by making certain that the ucode pointer is not NULL
before deregistering the driver in mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hv_kvp_daemon currently does not check whether fread() or fwrite()
succeed. Add the necessary checks. Also, remove the incorrect use of
feof() before fread().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux native exit codes are 8-bit unsigned values. exit(-1) results
in an exit code of 255, which is usually reserved for shells reporting
'command not found'. Use the portable value EXIT_FAILURE. (Not that
this matters much for a daemon.)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.
Problem Observed/rootcause:
When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.
Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.
Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a
couple of long standing reports of this but at the same time we can avoid killing the box.
Signed-off-by: Stanislav Kozina <skozina@redhat.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When `do_cmd_ioctl()` allocates memory for the kernel copy of a channel
list, it frees any previously allocated channel list in
`async->cmd.chanlist` and replaces it with the new one. However, if the
device is ever removed (or "detached") the cleanup code in
`cleanup_device()` in "drivers.c" does not free this memory so it is
lost.
A sensible place to free the kernel copy of the channel list is in
`do_become_nonbusy()` as at that point the comedi asynchronous command
associated with the channel list is no longer valid. Free the channel
list in `do_become_nonbusy()` instead of `do_cmd_ioctl()` and clear the
pointer to prevent it being freed more than once.
Note that `cleanup_device()` could be called at an inappropriate time
while the comedi device is open, but that's a separate bug not related
to this this patch.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`parse_insn()` is dereferencing the user-space pointer `insn->data`
directly when handling the `INSN_INTTRIG` comedi instruction. It
shouldn't be using `insn->data` at all; it should be using the separate
`data` pointer passed to the function. Fix it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct a direct dereference of I/O memory to use an appropriate I/O
memory access function. Note that the pointer being dereferenced is not
currently tagged with `__iomem` but I plan to correct that for 3.7.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`s626_enc_insn_config()` is incorrectly dereferencing `insn->data` which
is a pointer to user memory. It should be dereferencing the separate
`data` parameter that points to a copy of the data in kernel memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three call sites for this function, and all three
are called within a keyboard handler.
kbd_event_lock is already held within keyboard handlers,
so attempting to lock it in vt_get_leds causes deadlock.
Signed-off-by: Christopher Brannon <chris@the-brannons.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
softsynth_read() reads a character at a time from the init string;
when it finds the null terminator it sets the initialized flag but
then repeats the last character.
Additionally, if the read() buffer is not big enough for the init
string, the next read() will start reading from the beginning again.
So the caller may never progress to reading anything else.
Replace the simple initialized flag with the current position in
the init string, carried over between calls. Switch to reading
real data once this reaches the null terminator.
(This assumes that the length of the init string can't change, which
seems to be the case. Really, the string and position belong together
in a per-file private struct.)
Tested-by: Samuel Thibault <sthibault@debian.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/serial/usb-serial.c:1415:3-51: code aligned with following code on line 1416
vim +1415 drivers/usb/serial/usb-serial.c
1412 /* we only set the reset_resume field if the serial_driver has one */
1413 for (sd = serial_drivers; *sd; ++sd) {
1414 if ((*sd)->reset_resume)
> 1415 udriver->reset_resume = usb_serial_reset_resume;
> 1416 break;
1417 }
In 71c731a: usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
when extracting DMI strings (vendor or product_name) to mark them as quirk
we may get NULL pointer in case of non-x86 systems which won't define
CONFIG_DMI. Hence susbsequent strstr() calls crash while driver probing.
So, returning 'false' here in case we get a NULL vendor or product_name.
This is tested with ARM (exynos) system.
This patch should be backported to stable kernels as old as 3.6, that
contain the commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Sebastian Gottschall (DD-WRT) <s.gottschall@dd-wrt.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions. Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Thomas Schäfer <tschaefer@t-online.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FTDI FT2232H provides two serial channels (A and B), but on the TUMPA
channel A is dedicated to JTAG/SPI while channel B can be used for
UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as
a usb-serial interface to userspace.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have no idea what I've been thinking while I was doing this in the first
place. Now the strings are initialized properly and reported by lsusb.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was broken in 2e87edf49 ("usb: gadget: make g_printer use
composite").
The USB-strings were not setup properly and were not used. No function
was added which results in an empty USB config.
While fixing this, the interface number is now auto generated and not
hard coded to 0.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always clear QUEUE_FLAG_ADD_RANDOM if any underlying device does not
have it set. Otherwise devices with predictable characteristics may
contribute entropy.
QUEUE_FLAG_ADD_RANDOM specifies whether or not queue IO timings
contribute to the random pool.
For bio-based targets this flag is always 0 because such devices have no
real queue.
For request-based devices this flag was always set to 1 by default.
Now set it according to the flags on underlying devices. If there is at
least one device which should not contribute, set the flag to zero: If a
device, such as fast SSD storage, is not suitable for supplying entropy,
a request-based queue stacked over it will not be either.
Because the checking logic is exactly same as for the rotational flag,
share the iteration function with device_is_nonrot().
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The access beyond the end of device BUG_ON that was introduced to
dm_request_fn via commit 29e4013de7ad950280e4b2208 ("dm: implement
REQ_FLUSH/FUA support for request-based dm") was an overly
drastic (but simple) response to this situation.
I have received a report that this BUG_ON was hit and now think
it would be better to use dm_kill_unmapped_request() to fail the clone
and original request with -EIO.
map_request() will assign the valid target returned by
dm_table_find_target to tio->ti. But when the target
isn't valid tio->ti is never assigned (because map_request isn't
called); so add a check for tio->ti != NULL to dm_done().
Reported-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there are no paths and multipath receives an ioctl, it waits until
a path becomes available. This behaviour is incorrect if the
"queue_if_no_path" setting was not specified, as then the ioctl should
be rejected immediately, which this patch now does.
commit 35991652b ("dm mpath: allow ioctls to trigger pg init") should
have checked if queue_if_no_path was configured before queueing IO.
Checking for the queue_if_no_path feature, like is done in map_io(),
allows the following table load to work without blocking in the
multipath_ioctl retry loop:
IBM reported a deadlock in select_parent(). This was found to be caused
by taking rename_lock when already locked when restarting the tree
traversal.
There are two cases when the traversal needs to be restarted:
1) concurrent d_move(); this can only happen when not already locked,
since taking rename_lock protects against concurrent d_move().
2) racing with final d_put() on child just at the moment of ascending
to parent; rename_lock doesn't protect against this rare race, so it
can happen when already locked.
Because of case 2, we need to be able to handle restarting the traversal
when rename_lock is already held. This patch fixes all three callers of
try_to_ascend().
IBM reported that the deadlock is gone with this patch.
[ I rewrote the patch to be smaller and just do the "goto again" if the
lock was already held, but credit goes to Miklos for the real work.
- Linus ]
The open-coded mutex implementation for ARMv6+ cores suffers from a
severe lack of barriers, so in the uncontended case we don't actually
protect any accesses performed during the critical section.
Furthermore, the code is largely a duplication of the ARMv6+ atomic_dec
code but optimised to remove a branch instruction, as the mutex fastpath
was previously inlined. Now that this is executed out-of-line, we can
reuse the atomic access code for the locking (in fact, we use the xchg
code as this produces shorter critical sections).
This patch uses the generic xchg based implementation for mutexes on
ARMv6+, which introduces barriers to the lock/unlock operations and also
has the benefit of removing a fair amount of inline assembly code.
Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Reported-by: Shan Kang <kangshan0910@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't allocate enough data for this struct. As soon as we start
modifying event->event on the next lines, then we're going beyond the
end of the memory we allocated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442 Tested-by: Dominik Köppl <dominik@devwork.org> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
For GPIOs of gpio-lpc32xx, gpio_direction_output() ignores the value argument
(initial value of output). This patch fixes this by setting the level
accordingly.
Signed-off-by: Roland Stigge <stigge@antcom.de> Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.
This patches fixed the issue by adding the gpio valid check.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Reviewed-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mkl: backport to v3.5] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kthread_worker provides minimalistic workqueue-like interface for
users which need a dedicated worker thread (e.g. for realtime
priority). It has basic queue, flush_work, flush_worker operations
which mostly match the workqueue counterparts; however, due to the way
flush_work() is implemented, it has a noticeable difference of not
allowing work items to be freed while being executed.
While the current users of kthread_worker are okay with the current
behavior, the restriction does impede some valid use cases. Also,
removing this difference isn't difficult and actually makes the code
easier to understand.
This patch reimplements flush_kthread_work() such that it uses a
flush_work item instead of queue/done sequence numbers.
if (destroy)
svc_shutdown_net(nfsd_serv, net);
svc_destroy(nfsd_server);
svc_shutdown_net(nfsd_serv, net) calls nfsd_last_thread(), which sets
nfsd_serv to NULL, causing a NULL dereference on the following line.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACPI tables in the Macbook Air 5,1 define a single IOAPIC with id 2,
but the only remapping unit described in the DMAR table matches id 0.
Interrupt remapping fails as a result, and the kernel panics with the
message "timer doesn't work through Interrupt-remapped IO-APIC."
To fix this, check each IOAPIC for a corresponding IOMMU. If an IOMMU is
not found, do not allow IRQ remapping to be enabled.
v2: Move check to parse_ioapics_under_ir(), raise log level to KERN_ERR,
and add FW_BUG to the log message
v3: Skip check if IOMMU doesn't support interrupt remapping and remove
existing check that the IOMMU count equals the IOAPIC count
Newer firmware versions for the Pantech UML290 use a different
subclass ID. The Windows driver match on both IDs, so we do
that as well.
The ZTE (Vodafone) K5006-Z is a new device.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dcbw@redhat.com> Cc: Thomas Schäfer <tschaefer@t-online.de>
[bmork: backported to 3.4: use driver whitelisting] Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.
Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.
Lenovo provides a driver supporting 4 new devices:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with layout similar to MC7710
- MC7750 (114f:68a2) with layout similar to MC7710
- EM7700 (1199:901c) with layout similar to MC7710
Note regaring the three devices similar to MC7710:
The Windows drivers only support interface #8 on these
devices. The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).
We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way. Therefore limiting the new
devices to interface #8 for now.
[bmork: backported to 3.4: use driver whitelisting] Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Oops affects 3.5 kernels and older, and is due to lookup_one_len()
calling down to the dentry revalidation code with a NULL pointer
to struct nameidata.
It is fixed upstream by commit 0b728e1911c (stop passing nameidata *
to ->d_revalidate())
The i2c-powermac driver now creates the i2c devices properly
from the device-tree, including workarounds for broken or
missing device-tree bits, so let's just use the normal probe
methods and get rid of the hand made device creation code.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Elimar Riesebieter <riesebie@lxtec.de> Cc: Michel Dänzer <michel@daenzer.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a number of workarounds for broken Apple device-trees
mostly around sound chips. It handles creating the missing audio codec
devices and works around various issues with missing addresses or
missing compatible properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michel Dänzer <michel@daenzer.net> Cc: Elimar Riesebieter <riesebie@lxtec.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit 354ab8567ae3107a8cbe7228c3181990ba598aac titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab8567ae3107a8cbe7228c3181990ba598aac
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.
This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):
pch_uart_interrupt
spin_lock_irqsave(priv->port.lock, flags)
case PCH_UART_IID_RDR_TO (data ready)
handle_rx_to
push_rx
tty_port_tty_get
spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
...
tty_flip_buffer_push
...
flush_to_ldisc
spin_lock_irqsave(&tty->buf.lock)
spin_lock_irqsave(&tty->buf.lock)
disc->ops->receive_buf(tty, char_buf)
n_tty_receive_buf
tty->ops->flush_chars()
uart_flush_chars
uart_start
spin_lock_irqsave(&port->lock) <--- already hold this lock
Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver. Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.
V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
pch_console_write().
Note: Like the 8250 driver, if a printk is introduced anywhere inside
the pch_console_write() critical section, the kernel will hang
on a recursive spinlock on the private lock. The oops case is
handled by using a trylock in the oops_in_progress case.
Signed-off-by: Darren Hart <dvhart@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Feng Tang <feng.tang@intel.com> CC: Alexander Stein <alexander.stein@systec-electronic.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.
This patch adds enable/disable rx error interrupt code.
For some reason, when the lirc daemon learns that a usb remote control
has been unplugged, it wants to read the sysfs attributes of the
disappearing device. This is useful for uncovering transient
inconsistencies, but less so for keeping the system running when such
inconsistencies exist.
Under some circumstances (like every time I unplug my dvb stick from
my laptop), lirc catches an rc_dev whose raw event handler has been
removed (presumably by ir_raw_event_unregister), and proceeds to
interrogate the raw protocols supported by the NULL pointer.
This patch avoids the NULL dereference, and ignores the issue of how
this state of affairs came about in the first place.
Version 2 incorporates changes recommended by Mauro Carvalho Chehab
(-ENODEV instead of -EINVAL, and a signed-off-by).
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If update_wall_time() is called and the current offset isn't large
enough to accumulate, avoid re-calling timekeeping_adjust which may
change the clock freq and can cause 1ns inconsistencies with
CLOCK_REALTIME_COARSE/CLOCK_MONOTONIC_COARSE.
Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1345595449-34965-5-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unexpected behavior could occur if the time is set to a value large
enough to overflow a 64bit ktime_t (which is something larger then the
year 2262).
Also unexpected behavior could occur if large negative offsets are
injected via adjtimex.
So this patch improves the sanity check timekeeping inputs by
improving the timespec_valid() check, and then makes better use of
timespec_valid() to make sure we don't set the time to an invalid
negative value or one that overflows ktime_t.
Note: This does not protect from setting the time close to overflowing
ktime_t and then letting natural accumulation cause the overflow.
Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1344454580-17031-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For one, the driver device pointer needs to be filled in, or the lirc core
will refuse to load the driver. And we really need to wire up all the
platform_device bits. This has been tested via the lirc sourceforge tree
and verified to work, been sitting there for months, finally getting
around to sending it. :\
Stefan reported a crash on a kernel before a3e5d1091c1 ("sched:
Don't call task_group() too many times in set_task_rq()"), he
found the reason to be that the multiple task_group()
invocations in set_task_rq() returned different values.
Looking at all that I found a lack of serialization and plain
wrong comments.
The below tries to fix it using an extra pointer which is
updated under the appropriate scheduler locks. Its not pretty,
but I can't really see another way given how all the cgroup
stuff works.
Reported-and-tested-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1340364965.18025.71.camel@twins Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch tries to fix a dead loop in async_synchronize_full(), which
could be seen when preemption is disabled on a single cpu machine.
void async_synchronize_full(void)
{
do {
async_synchronize_cookie(next_cookie);
} while (!list_empty(&async_running) || !
list_empty(&async_pending));
}
async_synchronize_cookie() calls async_synchronize_cookie_domain() with
&async_running as the default domain to synchronize.
However, there might be some works in the async_pending list from other
domains. On a single cpu system, without preemption, there is no chance
for the other works to finish, so async_synchronize_full() enters a dead
loop.
It seems async_synchronize_full() wants to synchronize all entries in
all running lists(domains), so maybe we could just check the entry_count
to know whether all works are finished.
Currently, async_synchronize_cookie_domain() expects a non-NULL running
list ( if NULL, there would be NULL pointer dereference ), so maybe a
NULL pointer could be used as an indication for the functions to
synchronize all works in all domains.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case that the link is already in the connected state and a
Pairing request arrives from the mgmt interface, hci_conn_security()
would be called but it was not considering LE links.
Reported-by: João Paulo Rechi Vita <jprvita@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.
This also makes it clear that it is checking the security of the link.
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Tested-by: Shea Levy <shea@shealevy.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so the other CPU may temporarily see worker->flags which doesn't have
either WORKER_UNBOUND or WORKER_REBIND set and perform local wakeup
prematurely.
Fix it by using single explicit assignment via ACCESS_ONCE().
Because idle workers have another WORKER_NOT_RUNNING flag, this bug
doesn't exist for them; however, update it to use the same pattern for
consistency.
tj: Applied the change to idle workers too and updated comments and
patch description a bit.
This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.
This fix is also needed in stable version 3.5.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver can't get the HW ready, we would release
the interrupt twice which made the kernel complain loudly.
Reported-by: Brian Cockrell <brian.cockrell@intel.com> Tested-by: Brian Cockrell <brian.cockrell@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
Currently we've only frobbed this bit at irq_init time, but did
not restore it at resume time. Move it to the gen3 clock gating
function to fix this.
Notice while reading through code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
projects / karo-tx-linux.git / log