V4L/DVB (11981): Remote control debugging for dw2102 driver based USB cards
Remote control debugging for dw2102 driver based USB cards
It includes DVBWorld, TeVii, Terratec and others.
Type 'modprobe dvb-usb-dw2102 debug=4', then look at dmesg output.
Signed-off-by: Igor M. Liplianin <liplianin@me.by> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11979): em28xx: don't create audio device if not supported
In cases where the device does not actually provide a USB audio class *or*
vendor audio, do not load the driver that provides vendor audio support (such
as the KWorld 2800d). Otherwise, the /dev/audio1 device file gets created and
users get confused.
Also, reworks the logic a bit so that we don't try to inspect the register
content if the register read failed entirely.
Hans Verkuil [Fri, 12 Jun 2009 06:38:15 +0000 (03:38 -0300)]
V4L/DVB (11967): v4l: i2c modules must be linked before the v4l2 drivers
Since i2c autoprobing is no longer supported by v4l2 we need to make sure
that the i2c modules are linked before the v4l2 modules. The v4l2 modules
now rely on the presence of the i2c modules, so these must have initialized
themselves before the v4l2 modules.
The exception is the ir-kbd-i2c module, which is the only one still using
autoprobing. This one should be loaded at the end of the v4l2 module. Loading
it earlier actually causes problems with tveeprom. Once ir-kbd-i2c is no
longer autoprobing, then it has to move up as well.
This is only an issue when everything is compiled into the kernel.
Thanks to Marcus Swoboda for reporting this and Udo Steinberg for testing
this patch.
Tested-by: Udo A. Steinberg <udo@hypervisor.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression caused by changeset 9133:64aed7485a43 - v4l: disconnect
kernel number from minor
Before the above changeset, ov511_probe used to allow forcing to use a
certain specific set of video devices, like:
modprobe ov511 unit_video=4,1,3 num_uv=3
So, assuming that you have 5 ov511 devices, and connect they one by one,
they'll gain the following device numbers (at the connection order):
/dev/video4
/dev/video1
/dev/video3
/dev/video0
/dev/video2
However, this was changed due to this change at video_register_device():
+ nr = find_next_zero_bit(video_nums[type], minor_cnt, nr == -1 ? 0 : nr);
With the previous behavior, a trial to register on an already allocated mirror
would fail, and a loop would get the next requested minor. However, the current
behavior is to get the next available minor instead of failing. Due to that,
this means that the above modprobe parameter will give, instead:
Trent Piepho [Thu, 11 Jun 2009 08:33:00 +0000 (05:33 -0300)]
V4L/DVB (11964): b2c2: Fix problems with frontend attachment
The frontend attachment code didn't handle cases where the frontend
partially failed to attach. For instance, when the demod was attached
successfully but the tuner driver wasn't compiled or fails to init for some
reason. In these cases we try to clean up the partial attachment and fail
instead of proceeding with a broken frontend.
If frontend registration fails, clean up with dvb_frontend_detach() rather
than just calling the frontend's main release method. The former does some
additional stuff, like release an attached tuner and take care of putting
symbols when dynamic binding is used.
In skystar2_rev23_attach() it's not necessary to set fc->dev_type, that
gets set before skystar2_rev23_attach() is called.
V4L/DVB (11960): v4l: generate KEY_CAMERA instead of BTN_0 key events on input devices
A bunch of V4L drivers generate BTN_0 instead of KEY_CAMERA key presses.
X11 is able to handle KEY_CAMERA automatically these days while BTN_0 is
not treated at all. Thus it would be of big benefit if the camera drivers
would consistently generate KEY_CAMERA. Some drivers (uvc) already do,
this patch updates the remaining drivers to do the same.
I only possess a limited set of webcams, so this isn't tested with all
cameras. The patch is rather trivial and compile tested, so I'd say it's
still good enough to get merged.
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Alexey Klimov [Thu, 11 Jun 2009 03:22:42 +0000 (00:22 -0300)]
V4L/DVB (11957): dsbr100: change radio->muted to radio->status, update suspend/resume
Patch renames radio->muted to radio->status, add defines for that
variable, and fixes suspend/resume procedure. Radio->status set to
STOPPED in usb_dsbr100_probe because of removing open call.
Also, patch increases driver version.
Andy Walls [Tue, 9 Jun 2009 23:47:21 +0000 (20:47 -0300)]
V4L/DVB (11951): cx18: Add DVB-T support for the Leadtek WinFast DVR3100 H
This adds support for DVB-T on the Leadtek DVR3100 H and should also get analog
TV capture from the tuner working properly as well.
DVB-T 6 MHz and 8 MHz have been tested and verified to work by Terry Wu of
Leadtek. DVB-T 7 MHz has also been verified working with a change developed by
Terry to the tuner-xc2028.c driver.
Special thanks go to Terry Wu <terrywu2009@gmail.com> of Leadtek who provided
the needed information and testing to get digital TV working for the Leadtek
DVR3100 H.
Reported-by: Terry Wu <terrywu2009@gmail.com> Tested-by: Terry Wu <terrywu2009@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Herton Ronaldo Krzesinski from Mandriva reported that one Bison Electronics
webcam exposes a non-UVC interface descriptor. Instead of failing completely,
ignore trailing non-UVC descriptors and move on.
Thanks to Herton for reporting the problem and submitting a patch proposal.
V4L/DVB (11945): uvcvideo: Don't accept to change the format when buffers are allocated.
Setting a new frame format or size will likely change the buffer size required
to store a complete video frame. To avoid a buffer overflow, don't allow
VIDIOC_S_FMT calls when video buffers are already allocated.
Laurent Pinchart [Sun, 31 May 2009 20:05:55 +0000 (17:05 -0300)]
V4L/DVB (11944): uvcvideo: Add generic control blacklist.
Another device (5986:0241) has been reported to advertise a UVC control it
does not support. Rework the control blacklist to match devices by their
VID:PID instead of trying to be clever about which controls might not be
supported properly.
Erik Andrén [Thu, 11 Jun 2009 20:20:23 +0000 (17:20 -0300)]
V4L/DVB (11942): gspca - m5602-ov9650: Reorder quirk list and add A7V quirk
The quirk list has grown and was in need of sorting. This is now done. Add a new vflip quirk for the ASUS A7V while we're at it. Thanks to Carsten Menzel for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Mon, 25 May 2009 01:22:41 +0000 (22:22 -0300)]
V4L/DVB (11934): Change order for FM tune
Change order data of buffer in FM simple_tune function. It is usefull for:
1. Set data of tuner with CP bit UP. 0xCE for MK5 or 0xC6 for MK3
2. When call simple_fm_tune, read this byte from config and overwrite
this byte in function simple_radio_bandswitch for set CP bit to OFF.
Of course it can be usefull for other tuner for overwrite default
settings of FM.
V4L/DVB (11928): au0828: provide module option to disable USB speed check
Add an au0828 module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
V4L/DVB (11927): em28xx: provide module option to disable USB speed check
Add an em28xx module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
V4L/DVB (11925): em28xx: Add support for the K-World 2800d
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11924): au0828: Don't let device work unless connected to a high speed USB port
The au0828 basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
V4L/DVB (11923): em28xx: Don't let device work unless connected to a high speed USB port
The em28xx basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
V4L/DVB (11917): Fix firmware load for DVB-T @ 6MHz bandwidth for xc3028/xc3028L
The only two countries that are known to use 6MHz bandwidth are Taiwan
and Uruguay. Both use QAM subcarriers at OFTM.
This patch fixes the firmware load for such countries, where the
required firmware is the QAM one.
This also confirms the previous tests where it was noticed that the 6MHz
QAM firmware doesn't work for cable. So, this patch also removes support
for DVB-C, instead of just printing a warning.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com> Acked-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Fri, 29 May 2009 23:54:02 +0000 (20:54 -0300)]
V4L/DVB (11898): cx18: Perform 64 bit divide so it works for 32 bit systems
Thanks to David Ward and Mike Krufky for reporting the problem and
debugging this as an unresolved symbol due to a 64 bit divide on a 32 bit
system. David Ward provided the content of this patch; Andy Walls only
performed some cosmetic edits.
Reported-by: David Ward <david.ward@gatech.edu> Signed-off-by: David Ward <david.ward@gatech.edu> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Wong [Mon, 18 May 2009 08:25:49 +0000 (05:25 -0300)]
V4L/DVB (11880): cx23885: support for card Mygica X8506 DMB-TH
This patch add cx23885 support for card "Mygica X8506 DMB-TH".
It should work on "Magic-Pro ProHDTV Extreme" as well, as they are
same hardware with different branding.
Sign-off-by: David T.L. Wong <davidtlwong@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Miroslav Sustek [Sun, 31 May 2009 19:47:28 +0000 (16:47 -0300)]
V4L/DVB (11879): Adds support for Leadtek WinFast DTV-1800H
Enables analog/digital tv, radio and remote control (gpio).
Tested-by: Marcin Wojcikowski <emtees.mts@gmail.com> Tested-by: Karel Juhanak <karel.juhanak@warnet.cz> Tested-by: Andrew Goff <goffa72@gmail.com> Tested-by: Jan Novak <novak-j@seznam.cz> Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 17 May 2009 01:43:43 +0000 (22:43 -0300)]
V4L/DVB (11865): cx18: Tweak color burst gate delay and initial color sub-carrier freq
Fix the burst gate delays to use a crystal value of 28636360 as assumed by
the rest of the driver. Also have the initial color sub-carrier freq paramter
use the src decimation ratio per the documentation, instead of the actual
crystal/pixel clock ratio. The tracking circuit will find the correct color
subcarrier in any case, as long as we're close. Also fix up some debug print
statements.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Wed, 20 May 2009 19:06:10 +0000 (16:06 -0300)]
V4L/DVB (11860): saa7134: fix quirk in saa7134_i2c_xfer for the saa7131 bridge
The i2c quirk in the saa7134_i2c_xfer function does a bogus write
to i2c address 0xfd, to work around a bug in the silicon that
affects read transactions.
Unfortunately, this hack is not working properly, since the bogus
write is to 0xfd, an invalid i2c address. Fix this quirk by using
an actual valid i2c address, 0xfe, which is still unlikely to be
used as an i2c address for any actual i2c client.
This is required in order to properly communicate with a TDA10048
DVB-T demod located at i2c address 0x10 on the primary i2c bus.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
figo.zhang [Mon, 18 May 2009 02:31:55 +0000 (23:31 -0300)]
V4L/DVB (11853): minor have assigned value twice
The variable minor have assigned value twice, the first time is in the
initial "video_device" data struct in those drivers, pls see
saa7134-video.c,line 2503.
Jean Delvare [Wed, 13 May 2009 19:56:20 +0000 (16:56 -0300)]
V4L/DVB (11850): pvrusb2: Instantiate ir_video I2C device by default
Now that the ir-kbd-i2c driver has been converted to a new-style i2c
driver, we can instantiate the ir_video I2C device by default. The
pvr2_disable_ir_video is kept to disable the IR receiver, either
because the user doesn't use it, or for debugging purpose.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 13 May 2009 19:52:44 +0000 (16:52 -0300)]
V4L/DVB (11848): saa7134: Simplify handling of IR on AVerMedia Cardbus E506R
Now that we instantiate I2C IR devices explicitly, we can skip probing
altogether on boards where the I2C IR device address is known. The
AVerMedia Cardbus E506R is one of these boards.
Jean Delvare [Wed, 13 May 2009 19:51:46 +0000 (16:51 -0300)]
V4L/DVB (11847): saa7134: Simplify handling of IR on MSI TV@nywhere Plus
Now that we instantiate I2C IR devices explicitly, we can skip probing
altogether on boards where the I2C IR device address is known. The MSI
TV@nywhere Plus is one of these boards.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 13 May 2009 19:50:11 +0000 (16:50 -0300)]
V4L/DVB (11846): ir-kbd-i2c: Don't assume all IR receivers are supported
The code in ir_probe makes the dangerous assumption that all IR
receivers are supported by the driver. The new i2c model makes it
possible for bridge drivers to instantiate IR devices before they are
supported, therefore the ir-kbd-i2c drivers must be made more robust
to not spam the logs or even crash on unsupported IR devices. Simply,
the driver will not bind to the unsupported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 13 May 2009 19:49:32 +0000 (16:49 -0300)]
V4L/DVB (11845): ir-kbd-i2c: Use initialization data
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 13 May 2009 19:48:50 +0000 (16:48 -0300)]
V4L/DVB (11844): ir-kbd-i2c: Switch to the new-style device binding model
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Wed, 13 May 2009 19:48:07 +0000 (16:48 -0300)]
V4L/DVB (11843): ir-kbd-i2c: Don't use i2c_client.name for our own needs
In the standard device driver binding model, the name field of
struct i2c_client is used to match devices to their drivers, so we
must stop using it for internal purposes. Define a separate field
in struct IR_i2c as a replacement, and use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11842): radio-mr800.c: missing mutex include
radio-mr800.c uses struct mutex, so while <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it already includes, the right
thing is to include it directly.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Alexey Klimov <klimov.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simon Arlott [Tue, 12 May 2009 20:39:28 +0000 (17:39 -0300)]
V4L/DVB (11841): core: fix potential mutex_unlock without mutex_lock in dvb_dvr_read
dvb_dvr_read may unlock the dmxdev mutex and return -ENODEV, except this
function is a file op and will never be called with the mutex held.
There's existing mutex_lock and mutex_unlock around the actual read but
it's commented out. These should probably be uncommented but the read
blocks and this could block another non-blocking reader on the mutex
instead.
This change comments out the extra mutex_unlock.
[akpm@linux-foundation.org: cleanups, simplification] Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cohen David.A [Mon, 11 May 2009 14:00:20 +0000 (11:00 -0300)]
V4L/DVB (11840): change kmalloc to vmalloc for sglist allocation in videobuf_dma_map/unmap
Change kmalloc()/kfree() to vmalloc()/vfree() for sglist allocation
during videobuf_dma_map() and videobuf_dma_unmap()
High resolution sensors might require too many contiguous pages
to be allocated for sglist by kmalloc() during videobuf_dma_map()
(i.e. 256Kib for 8MP sensor).
In such situations, kmalloc() could face some problem to find the
required free memory. vmalloc() is a safer solution instead, as the
allocated memory does not need to be contiguous.
Signed-off-by: David Cohen <david.cohen@nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Laurent Pinchart [Tue, 19 May 2009 13:08:03 +0000 (10:08 -0300)]
V4L/DVB (11837): uvcvideo: Start status polling on device open
Most UVC camera include an interrupt endpoint to report control value changes,
video streaming errors and camera button events. The USB controller
continuously polls the interrupt endpoint to retrieve such events. This
prevents the device from being auto-suspended, and thus consumes power.
Reporting video streaming errors don't make sense when the V4L2 device is
closed. Control value changes are probably useless as well if nobody listens to
the events, although caching will probably have to be completely disabled then.
No polling is thus be required when /dev/videoX is not opened.
To enable auto-suspend and save power do not poll the interrupt endpoint until
the device is open. We lose the ability to detect button events if no
application is using the camera.
V4L/DVB (11835): uvcvideo: Parse frame descriptors with non-continuous indexes.
The UVC specification requires frame descriptors indexes to range from 1 to
the number of frame descriptors. At least some Hercules Dualpix Infinite
webcams erroneously use non-continuous index ranges. Make the driver support
them.
Alan Nisota [Wed, 20 May 2009 08:52:13 +0000 (05:52 -0300)]
V4L/DVB (11833): dvb-usb: Remove support for Genpix-CW3K (damages hardware)
I have been informed by the manufacturer that the patch currently in the v4l tree to support the Genpix-CW3K version of the hardware will actually
damage the firmware on recent units. As he seems to not want this hardware supported in Linux, and I do not know how to detect the difference between
affected and not-affected units, I am requesting the immediate removal of support for this device. This patch removes a portion of the changeset dce7e08ed2b1 applied 2007-08-18 relating to this specific device.
Adapted patch to not remove code, but to only to comment it out.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
matthieu castet [Wed, 20 May 2009 08:42:33 +0000 (05:42 -0300)]
V4L/DVB (11832): dibusb_mc: fix i2c to not corrupt eeprom in case of strange read pattern
dibusb_i2c_xfer seems to do things very dangerous :
it assumes that it get only write/read request or write request.
That means that read can be understood as write. For example a program
doing
file = open("/dev/i2c-x", O_RDWR);
ioctl(file, I2C_SLAVE, 0x50)
read(file, data, 10)
will corrupt the eeprom as it will be understood as a write.
tomas petr [Wed, 20 May 2009 08:28:05 +0000 (05:28 -0300)]
V4L/DVB (11830): dib0700: add support for Leadtek WinFast DTV Dongle H
"Leadtek WinFast DTV Dongle H" is a hybrid digital/analog USB-stick TV
receiver. The code below allows the digital part to work with dvb_usb
in linux.
Signed-off-by: tomas petr <tom-petr@seznam.cz> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11810): em28xx: properly set packet size based on the device's eeprom configuration.
The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom). Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).
Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).
Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.
V4L/DVB (11808): au0828: get rid of debug printk that was causing compile failures
Remove a debug printk() line I added which is no longer needed, and happened
to be causing compile failures on some earlier kernels in Han's daily
compile report.
V4L/DVB (11807): cx88: remove xc5000 reset for Pinnacle 800i
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed
to be on GPIO12. However, despite three nights of effort, pulling that GPIO
low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the
xc5000, this also resets in the s5h1409 being reset as well. This causes
tuning to always fail since the internal state of the s5h1409 does not match
the driver's state.
Given that the only two conditions in which the driver performs a reset is
during firmware load and powering down the chip, I am taking out the reset.
We know that the chip is being reset when the cx88 comes online, and not being
able to do power management for this board is better than not having any
tuning at all.
Problem discovered when implementing proper power management for the xc5000,
which results in calls to the reset callback *after* s5h1409 is initialized.