Apple cards do not provide data tables in the vbios
so we have to hard code the connector parameters
in the driver.
Reported-by: Albrecht Dreß <albrecht.dress@arcor.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The locking in update_vsyscall_tz() is not only unnecessary because the vdso
code copies the data unproteced in __kernel_gettimeofday() but also
introduces a hard to reproduce race condition between update_vsyscall()
and update_vsyscall_tz(), which causes user space process to loop
forever in vdso code.
The following patch removes the locking from update_vsyscall_tz().
Locking is not only unnecessary because the vdso code copies the data
unprotected in __kernel_gettimeofday() but also erroneous because updating
the tb_update_count is not atomic and introduces a hard to reproduce race
condition between update_vsyscall() and update_vsyscall_tz(), which further
causes user space process to loop forever in vdso code.
The below scenario describes the race condition,
x==0 Boot CPU other CPU
proc_P: x==0
timer interrupt
update_vsyscall
x==1 x++;sync settimeofday
update_vsyscall_tz
x==2 x++;sync
x==3 sync;x++
sync;x++
proc_P: x==3 (loops until x becomes even)
Because the ++ operator would be implemented as three instructions and not
atomic on powerpc.
A similar change was made for x86 in commit 6c260d58634
("x86: vdso: Remove bogus locking in update_vsyscall_tz")
Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It also adds a note about Gemtek WUBI-100GW
and SparkLAN WL-682 USBID conflict [WUBI-100GW
is a ISL3886+NET2280 (LM86 firmare) solution,
whereas WL-682 is a ISL3887 (LM87 firmware)]
device.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA
mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts
or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often
in a page table (causing "Bad swap" or "Bad page map" warning or "Bad
pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere
worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic.
Recent NUMA enhancements are not to blame: this dates back to 2.6.35,
when commit e17f74af351c "mempolicy: don't call mpol_set_nodemask() when
no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(),
which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags.
With slab poisoning, you can then rely on mpol_to_str() to set the bit
for node 0x6b6b, probably in the next page above the caller's stack.
mpol_parse_str() is only called from shmem_parse_options(): no_context
is always true, so call it unused for now, and remove !no_context code.
Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might
expect. Then mpol_to_str() can ignore its no_context argument also,
the mpol being appropriately initialized whether contextualized or not.
Rename its no_context unused too, and let subsequent patch remove them
(that's not needed for stable backporting, which would involve rejects).
I don't understand why MPOL_LOCAL is described as a pseudo-policy:
it's a reasonable policy which suffers from a confusing implementation
in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be
much more robust if MPOL_LOCAL were recognized in switch statements
throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly
empty) nodes mask like everyone else, instead of its preferred_node
variant (I presume an optimization from the days before MPOL_LOCAL).
But that would take me too long to get right and fully tested.
When a call goes out, the signing code adjusts the sequence number
upward by two to account for the request and the response. An NT_CANCEL
however doesn't get a response of its own, it just hurries the server
along to get it to respond to the original request more quickly.
Therefore, we must adjust the sequence number back down by one after
signing a NT_CANCEL request.
Reported-by: Tim Perry <tdparmor-sambabugs@yahoo.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Unfortunately with !CONFIG_PAGEFLAGS_EXTENDED, (!PageHead) is false, and
(PageHead) is true, for tail pages. If this is indeed the intended
behavior, which I doubt because it breaks cache cleaning on some ARM
systems, then the nomenclature is highly problematic.
This patch makes sure PageHead is only true for head pages and PageTail
is only true for tail pages, and neither is true for non-compound pages.
[ This buglet seems ancient - seems to have been introduced back in Apr
2008 in commit 6a1e7f777f61: "pageflags: convert to the use of new
macros". And the reason nobody noticed is because the PageHead()
tests are almost all about just sanity-checking, and only used on
pages that are actual page heads. The fact that the old code returned
true for tail pages too was thus not really noticeable. - Linus ]
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu> Acked-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Will Deacon <Will.Deacon@arm.com> Cc: Steve Capper <Steve.Capper@arm.com> Cc: Christoph Lameter <cl@linux.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a journal-less ext4 filesystem is mounted on a read-only block
device (blockdev --setro will do), each remount (for other, unrelated,
flags, like suid=>nosuid etc) results in a series of scary messages
from kernel telling about I/O errors on the device.
This is becauese of the following code ext4_remount():
if (sbi->s_journal == NULL)
ext4_commit_super(sb, 1);
at the end of remount procedure, which forces writing (flushing) of
a superblock regardless whenever it is dirty or not, if the filesystem
is readonly or not, and whenever the device itself is readonly or not.
We only need call ext4_commit_super when the file system had been
previously mounted read/write.
Thanks to Eric Sandeen for help in diagnosing this issue.
Signed-off-By: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If an LM73 device does not exist on an I2C bus, attempts to communicate
with the device result in an error code returned from the i2c read/write
functions. The current lm73 driver casts that return value from a s32
type to a s16 type, then converts it to a temperature in celsius.
Because negative temperatures are valid, it is difficult to distinguish
between an error code printed to the response buffer and a negative
temperature recorded by the sensor.
The solution is to evaluate the return value from the i2c functions
before performing any temperature calculations. If the i2c function did
not succeed, the error code should be passed back through the virtual
file system layer instead of being printed into the response buffer.
The following race is possible between start_this_handle() and someone
calling jbd2_journal_flush().
Process A Process B
start_this_handle().
if (journal->j_barrier_count) # false
if (!journal->j_running_transaction) { #true
read_unlock(&journal->j_state_lock);
jbd2_journal_lock_updates()
jbd2_journal_flush()
write_lock(&journal->j_state_lock);
if (journal->j_running_transaction) {
# false
... wait for committing trans ...
write_unlock(&journal->j_state_lock);
...
write_lock(&journal->j_state_lock);
if (!journal->j_running_transaction) { # true
jbd2_get_transaction(journal, new_transaction);
write_unlock(&journal->j_state_lock);
goto repeat; # eventually blocks on j_barrier_count > 0
...
J_ASSERT(!journal->j_running_transaction);
# fails
We fix the race by rechecking j_barrier_count after reacquiring j_state_lock
in exclusive mode.
Reported-by: yjwsignal@empal.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently we allow enabling dioread_nolock mount option on remount for
filesystems where blocksize < PAGE_CACHE_SIZE. This isn't really
supported so fix the bug by moving the check for blocksize !=
PAGE_CACHE_SIZE into parse_options(). Change the original PAGE_SIZE to
PAGE_CACHE_SIZE along the way because that's what we are really
interested in.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some broken systems (like HP nc6120) in some cases, usually after LID
close/open, enable VGA plane, making display unusable (black screen on LVDS,
some strange mode on VGA output). We used to disable VGA plane only once at
startup. Now we also check, if VGA plane is still disabled while changing
mode, and fix that if something changed it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434 Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: intel_modeset_setup_hw_state() does not
exist, so call i915_redisable_vga() directly from intel_lid_notify()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The return value of rounddown_pow_of_two wasn't evaluated, so the
operation was a no-op.
Signed-off-by: Marco Stornelli <marco.stornelli@gmail.com> Reported-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On COW, a new hugepage is allocated and charged to the memcg. If the
system is oom or the charge to the memcg fails, however, the fault
handler will return VM_FAULT_OOM which results in an oom kill.
Instead, it's possible to fallback to splitting the hugepage so that the
COW results only in an order-0 page being allocated and charged to the
memcg which has a higher liklihood to succeed. This is expensive
because the hugepage must be split in the page fault handler, but it is
much better than unnecessarily oom killing a process.
Signed-off-by: David Rientjes <rientjes@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Johannes Weiner <jweiner@redhat.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix bug reported at:
https://bugzilla.redhat.com/show_bug.cgi?id=848149
And, very likely:
https://bbs.archlinux.org/viewtopic.php?id=148033
https://bugzilla.kernel.org/show_bug.cgi?id=47171
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2:
- Adjust context
- Use csrow->channels[chan].label not csrow->channels[chan]->dimm->label] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
pci_disable_device(pdev) used to be in pci remove function. But this
PCI device has two functions with interrupt lines connected to a
single pin. The other one is a USB host controller. So when we disable
the PIN there e.g. by rmmod hpilo, the controller stops working. It is
because the interrupt link is disabled in ACPI since it is not
refcounted yet. See acpi_pci_link_free_irq called from
acpi_pci_irq_disable.
It is not the best solution whatsoever, but as a workaround until the
ACPI irq link refcounting is sorted out this should fix the reported
errors.
References: https://lkml.org/lkml/2008/11/4/535
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Grant Grundler <grundler@parisc-linux.org> Cc: Nobin Mathew <nobin.mathew@gmail.com> Cc: Robert Hancock <hancockr@shaw.ca> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Altobelli <david.altobelli@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The RX replenish code doesn't handle DMA mapping failures,
which will cause issues if there actually is a failure. This
was reported by Shuah Khan who found a DMA mapping framework
warning ("device driver failed to check map error").
Reported-by: Shuah Khan <shuah.khan@hp.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust filename, context, indentation
- Use bus(trans) instead of trans where necessary
- Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I noticed that the iPhone ethernet driver did not support
iPhone 5. I quickly added support to it in my kernel, here's
a patch.
Signed-off-by: Jay Purohit <jspurohit@velocitylimitless.com> Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ip_check_defrag() might be called from af_packet within the
RX path where shared SKBs are used, so it must not modify
the input SKB before it has unshared it for defragmentation.
Use skb_copy_bits() to get the IP header and only pull in
everything later.
The same is true for the other caller in macvlan as it is
called from dev->rx_handler which can also get a shared SKB.
Reported-by: Eric Leblond <eric@regit.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Noticed while running Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Trinity (the syscall fuzzer) discovered a memory leak in SCTP,
reproducible e.g. with the sendto() syscall by passing invalid
user space pointer in the second argument:
As far as I can tell, the leak has been around since ~2003.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Race between bonding_store_slaves_active() and slave manipulation
functions. The bond_for_each_slave use in bonding_store_slaves_active()
is not protected by any synchronization mechanism.
NULL pointer dereference is easy to reach.
Fixed by acquiring the bond->lock for the slave walk.
v2: Make description text < 75 columns
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB: cdc-wdm: fix regression on buffer deallocation
[ no commit upstream, since usb_alloc_coherent usage was removed from
the driver before this was fixed ]
Commit cafbe85 ("USB: cdc-wdm: better allocate a buffer that is at least
as big as we tell the USB core") introduced a regression: it changed
the size used in usb_alloc_coherent, but failed to do the same for the
usb_free_coherent calls.
It also was marked for stable and got backported to older kernels. But
in the upstream kernel, the usage of usb_alloc_coherent was right after
removed from the driver, so upstream doesn't have this problem, while
the stable kernels still have, and thus need this fix.
BugLink: https://bugs.launchpad.net/bugs/1074157 Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
drm/i915: parse eDP panel color depth from VBT block
originally introduced parsing bpp for eDP from VBT, with a default of 18
bpp if the eDP BIOS data block is not present. Turns out that default seems
to break the Macbook Pro with retina display, as noted in
Since we can't ignore bpc settings from VBT completely after all, get rid
of the default. Do not clamp eDP to 18 bpp by default if the eDP BDB is
missing from VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com> Tested-by: Henrik Rydberg <rydberg@euromail.se>
[danvet: paste in the updated commit message from irc.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
but putting the VBT check after the EDID check to see them both in dmesg if
this clamps more than the EDID. We have enough history with bpc clamping to
warrant the extra debug info.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47641
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56401 Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Abort dm ioctl processing if userspace changes the data_size parameter
after we validated it but before we finished copying the data buffer
from userspace.
The dm ioctl parameters are processed in the following sequence:
1. ctl_ioctl() calls copy_params();
2. copy_params() makes a first copy of the fixed-sized portion of the
userspace parameters into the local variable "tmp";
3. copy_params() then validates tmp.data_size and allocates a new
structure big enough to hold the complete data and copies the whole
userspace buffer there;
4. ctl_ioctl() reads userspace data the second time and copies the whole
buffer into the pointer "param";
5. ctl_ioctl() reads param->data_size without any validation and stores it
in the variable "input_param_size";
6. "input_param_size" is further used as the authoritative size of the
kernel buffer.
The problem is that userspace code could change the contents of user
memory between steps 2 and 4. In particular, the data_size parameter
can be changed to an invalid value after the kernel has validated it.
This lets userspace force the kernel to access invalid kernel memory.
The fix is to ensure that the size has not changed at step 4.
This patch shouldn't have a security impact because CAP_SYS_ADMIN is
required to run this code, but it should be fixed anyway.
Reported-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes a compilation failure on sparc32 by renaming struct node.
struct node is already defined in include/linux/node.h. On sparc32, it
happens to be included through other dependencies and persistent-data
doesn't compile because of conflicting declarations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We found a user code which was raising a divide-by-zero trap. That trap
would lead to XPC connections between system-partitions being torn down
due to the die_chain notifier callouts it received.
This also revealed a different issue where multiple callers into
xpc_die_deactivate() would all attempt to do the disconnect in parallel
which would sometimes lock up but often overwhelm the console on very
large machines as each would print at least one line of output at the
end of the deactivate.
I reviewed all the users of the die_chain notifier and changed the code
to ignore the notifier callouts for reasons which will not actually lead
to a system to continue on to call die().
[akpm@linux-foundation.org: fix ia64] Signed-off-by: Robin Holt <holt@sgi.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a series of scripts are executed, each triggering module loading via
unprintable bytes in the script header, kernel stack contents can leak
into the command line.
Normally execution of binfmt_script and binfmt_misc happens recursively.
However, when modules are enabled, and unprintable bytes exist in the
bprm->buf, execution will restart after attempting to load matching
binfmt modules. Unfortunately, the logic in binfmt_script and
binfmt_misc does not expect to get restarted. They leave bprm->interp
pointing to their local stack. This means on restart bprm->interp is
left pointing into unused stack memory which can then be copied into the
userspace argv areas.
After additional study, it seems that both recursion and restart remains
the desirable way to handle exec with scripts, misc, and modules. As
such, we need to protect the changes to interp.
This changes the logic to require allocation for any changes to the
bprm->interp. To avoid adding a new kmalloc to every exec, the default
value is left as-is. Only when passing through binfmt_script or
binfmt_misc does an allocation take place.
NFS appears to use d_obtain_alias() to create the root dentry rather than
d_make_root. This can cause 'prepend_path()' to complain that the root
has a weird name if an NFS filesystem is lazily unmounted. e.g. if
"/mnt" is an NFS mount then
{ cd /mnt; umount -l /mnt ; ls -l /proc/self/cwd; }
will cause a WARN message like
WARNING: at /home/git/linux/fs/dcache.c:2624 prepend_path+0x1d7/0x1e0()
...
Root dentry has weird name <>
to appear in kernel logs.
So change d_obtain_alias() to use "/" rather than "" as the anonymous
name.
Signed-off-by: NeilBrown <neilb@suse.de> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[bwh: Backported to 3.2: use named initialisers instead of QSTR_INIT()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The dma_pte_free_pagetable() function will only free a page table page
if it is asked to free the *entire* 2MiB range that it covers. So if a
page table page was used for one or more small mappings, it's likely to
end up still present in the page tables... but with no valid PTEs.
This was fine when we'd only be repopulating it with 4KiB PTEs anyway
but the same virtual address range can end up being reused for a
*large-page* mapping. And in that case were were trying to insert the
large page into the second-level page table, and getting a complaint
from the sanity check in __domain_mapping() because there was already a
corresponding entry. This was *relatively* harmless; it led to a memory
leak of the old page table page, but no other ill-effects.
Fix it by calling dma_pte_clear_range (hopefully redundant) and
dma_pte_free_pagetable() before setting up the new large page.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Ravi Murty <Ravi.Murty@intel.com> Tested-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
find_vma() is *not* safe when somebody else is removing vmas. Not just
the return value might get bogus just as you are getting it (this instance
doesn't try to dereference the resulting vma), the search itself can get
buggered in rather spectacular ways. IOW, ->mmap_sem really, really is
not optional here.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The inb/outb macros for CRIS are broken from a number of points of view,
missing () around parameters and they have an unprotected if statement
in them. This was breaking the compile of IPMI on CRIS and thus I was
being annoyed by build regressions, so I fixed them.
Plus I don't think they would have worked at all, since the data values
were missing "&" and the outsl had a "3" instead of a "4" for the size.
From what I can tell, this stuff is not used at all, so this can't be
any more broken than it was before, anyway.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <starvik@axis.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We display a list of supplementary group for each process in
/proc/<pid>/status. However, we show only the first 32 groups, not all of
them.
Although this is rare, but sometimes processes do have more than 32
supplementary groups, and this kernel limitation breaks user-space apps
that rely on the group list in /proc/<pid>/status.
Number 32 comes from the internal NGROUPS_SMALL macro which defines the
length for the internal kernel "small" groups buffer. There is no
apparent reason to limit to this value.
This patch removes the 32 groups printing limit.
The Linux kernel limits the amount of supplementary groups by NGROUPS_MAX,
which is currently set to 65536. And this is the maximum count of groups
we may possibly print.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The workaround to force VREF50 for dallas/hp model with ALC861VD
was introduced in commit 8fdcb6fe4204bdb4c6991652717ab5063751414e,
but it contained wrong pincap override bits.
This patch fixes to exclude VREF80 pincap bit correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We've seen the broken HDMI *video* output on some machines with GM965,
and the debugging session pointed that the culprit is the disabled
audio output pins. Toggling these pins dynamically on demand caused
flickering of HDMI TV.
This patch changes the behavior to keep the pin ON constantly.
When poweroff machine, kernel_power_off() call disable_nonboot_cpus().
And if we have HOTPLUG_CPU configured, disable_nonboot_cpus() is not an
empty function but attempt to actually disable the nonboot cpus. Since
system state is SYSTEM_POWER_OFF, play_dead() won't be called and thus
disable_nonboot_cpus() hangs. Therefore, we make this patch to avoid
poweroff failure.
It could happen (1 out of 100 times) that NAND did not start up
correctly after warm rebooting, so the kernel could not find the UBI or
DMA timed out due to a stalled BCH. When resetting BCH together with
GPMI, the issue could not be observed anymore (after 10000+ reboots). We
probably need the consistent state already before sending any command to
NAND, even when no ECC is needed. I chose to keep the extra reset for
BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The lockdep warning below is in theory correct but it will be in really weird
rare situation that ends up that deadlock since the tcm fc session is hashed
based the rport id. Nonetheless, the complaining below is about rcu callback
that does the transport_deregister_session() is happening in softirq, where
transport_register_session() that happens earlier is not. This triggers the
lockdep warning below. So, just fix this to make lockdep happy by disabling
the soft irq before calling transport_register_session() in ft_prli.
BTW, this was found in FCoE VN2VN over two VMs, couple of create and destroy
would get this triggered.
v1: was enforcing register to be in softirq context which was not righ. See,
http://www.spinics.net/lists/target-devel/msg03614.html
v2: following comments from Roland&Nick (thanks), it seems we don't have to
do transport_deregister_session() in rcu callback, so move it into ft_sess_free()
but still do kfree() of the corresponding ft_sess struct in rcu callback to
make sure the ft_sess is not freed till the rcu callback.
...
[ 1328.370592] scsi2 : FCoE Driver
[ 1328.383429] fcoe: No FDMI support.
[ 1328.384509] host2: libfc: Link up on port (000000)
[ 1328.934229] host2: Assigned Port ID 00a292
[ 1357.232132] host2: rport 00a393: Remove port
[ 1357.232568] host2: rport 00a393: Port sending LOGO from Ready state
[ 1357.233692] host2: rport 00a393: Delete port
[ 1357.234472] host2: rport 00a393: work event 3
[ 1357.234969] host2: rport 00a393: callback ev 3
[ 1357.235979] host2: rport 00a393: Received a LOGO response closed
[ 1357.236706] host2: rport 00a393: work delete
[ 1357.237481]
[ 1357.237631] =================================
[ 1357.238064] [ INFO: inconsistent lock state ]
[ 1357.238450] 3.7.0-rc7-yikvm+ #3 Tainted: G O
[ 1357.238450] ---------------------------------
[ 1357.238450] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 1357.238450] ksoftirqd/0/3 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 1357.238450] (&(&se_tpg->session_lock)->rlock){+.?...}, at: [<ffffffffa01eacd4>] transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] {SOFTIRQ-ON-W} state was registered at:
[ 1357.238450] [<ffffffff810834f5>] mark_held_locks+0x6d/0x95
[ 1357.238450] [<ffffffff8108364a>] trace_hardirqs_on_caller+0x12d/0x197
[ 1357.238450] [<ffffffff810836c1>] trace_hardirqs_on+0xd/0xf
[ 1357.238450] [<ffffffff8149caba>] _raw_spin_unlock_irq+0x2d/0x45
[ 1357.238450] [<ffffffffa01e8d10>] __transport_register_session+0xb8/0x122 [target_core_mod]
[ 1357.238450] [<ffffffffa01e8dbe>] transport_register_session+0x44/0x5a [target_core_mod]
[ 1357.238450] [<ffffffffa018e32c>] ft_prli+0x1e3/0x275 [tcm_fc]
[ 1357.238450] [<ffffffffa0160e8d>] fc_rport_recv_req+0x95e/0xdc5 [libfc]
[ 1357.238450] [<ffffffffa015be88>] fc_lport_recv_els_req+0xc4/0xd5 [libfc]
[ 1357.238450] [<ffffffffa015c778>] fc_lport_recv_req+0x12f/0x18f [libfc]
[ 1357.238450] [<ffffffffa015a6d7>] fc_exch_recv+0x8ba/0x981 [libfc]
[ 1357.238450] [<ffffffffa0176d7a>] fcoe_percpu_receive_thread+0x47a/0x4e2 [fcoe]
[ 1357.238450] [<ffffffff810549f1>] kthread+0xb1/0xb9
[ 1357.238450] [<ffffffff814a40ec>] ret_from_fork+0x7c/0xb0
[ 1357.238450] irq event stamp: 275411
[ 1357.238450] hardirqs last enabled at (275410): [<ffffffff810bb6a0>] rcu_process_callbacks+0x229/0x42a
[ 1357.238450] hardirqs last disabled at (275411): [<ffffffff8149c2f7>] _raw_spin_lock_irqsave+0x22/0x8e
[ 1357.238450] softirqs last enabled at (275394): [<ffffffff8103d669>] __do_softirq+0x246/0x26f
[ 1357.238450] softirqs last disabled at (275399): [<ffffffff8103d6bb>] run_ksoftirqd+0x29/0x62
[ 1357.238450]
[ 1357.238450] other info that might help us debug this:
[ 1357.238450] Possible unsafe locking scenario:
[ 1357.238450]
[ 1357.238450] CPU0
[ 1357.238450] ----
[ 1357.238450] lock(&(&se_tpg->session_lock)->rlock);
[ 1357.238450] <Interrupt>
[ 1357.238450] lock(&(&se_tpg->session_lock)->rlock);
[ 1357.238450]
[ 1357.238450] *** DEADLOCK ***
[ 1357.238450]
[ 1357.238450] no locks held by ksoftirqd/0/3.
[ 1357.238450]
[ 1357.238450] stack backtrace:
[ 1357.238450] Pid: 3, comm: ksoftirqd/0 Tainted: G O 3.7.0-rc7-yikvm+ #3
[ 1357.238450] Call Trace:
[ 1357.238450] [<ffffffff8149399a>] print_usage_bug+0x1f5/0x206
[ 1357.238450] [<ffffffff8100da59>] ? save_stack_trace+0x2c/0x49
[ 1357.238450] [<ffffffff81082aae>] ? print_irq_inversion_bug.part.14+0x1ae/0x1ae
[ 1357.238450] [<ffffffff81083336>] mark_lock+0x106/0x258
[ 1357.238450] [<ffffffff81084e34>] __lock_acquire+0x2e7/0xe53
[ 1357.238450] [<ffffffff8102903d>] ? pvclock_clocksource_read+0x48/0xb4
[ 1357.238450] [<ffffffff810ba6a3>] ? rcu_process_gp_end+0xc0/0xc9
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff81085ef1>] lock_acquire+0x119/0x143
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff8149c329>] _raw_spin_lock_irqsave+0x54/0x8e
[ 1357.238450] [<ffffffffa01eacd4>] ? transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffffa01eacd4>] transport_deregister_session+0x41/0x148 [target_core_mod]
[ 1357.238450] [<ffffffff810bb6a0>] ? rcu_process_callbacks+0x229/0x42a
[ 1357.238450] [<ffffffffa018ddc5>] ft_sess_rcu_free+0x17/0x24 [tcm_fc]
[ 1357.238450] [<ffffffffa018ddae>] ? ft_sess_free+0x1b/0x1b [tcm_fc]
[ 1357.238450] [<ffffffff810bb6d7>] rcu_process_callbacks+0x260/0x42a
[ 1357.238450] [<ffffffff8103d55d>] __do_softirq+0x13a/0x26f
[ 1357.238450] [<ffffffff8149b34e>] ? __schedule+0x65f/0x68e
[ 1357.238450] [<ffffffff8103d6bb>] run_ksoftirqd+0x29/0x62
[ 1357.238450] [<ffffffff8105c83c>] smpboot_thread_fn+0x1a5/0x1aa
[ 1357.238450] [<ffffffff8105c697>] ? smpboot_unregister_percpu_thread+0x47/0x47
[ 1357.238450] [<ffffffff810549f1>] kthread+0xb1/0xb9
[ 1357.238450] [<ffffffff8149b49d>] ? wait_for_common+0xbb/0x10a
[ 1357.238450] [<ffffffff81054940>] ? __init_kthread_worker+0x59/0x59
[ 1357.238450] [<ffffffff814a40ec>] ret_from_fork+0x7c/0xb0
[ 1357.238450] [<ffffffff81054940>] ? __init_kthread_worker+0x59/0x59
[ 1417.440099] rport-2:0-0: blocked FC remote port time out: removing rport
Signed-off-by: Yi Zou <yi.zou@intel.com> Cc: Open-FCoE <devel@open-fcoe.org> Cc: Nicholas A. Bellinger <nab@risingtidesystems.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In rare circumstances, nfs_clone_server() of a v2 or v3 server can get
an error between setting server->destory (to nfs_destroy_server), and
calling nfs_start_lockd (which will set server->nlm_host).
If this happens, nfs_clone_server will call nfs_free_server which
will call nfs_destroy_server and thence nlmclnt_done(NULL). This
causes the NULL to be dereferenced.
So add a guard to only call nlmclnt_done() if ->nlm_host is not NULL.
The other guards there are irrelevant as nlm_host can only be non-NULL
if one of these flags are set - so remove those tests. (Thanks to Trond
for this suggestion).
This is suitable for any stable kernel since 2.6.25.
We weren't clearing card->tx_skb[port] when processing the TX done interrupt.
If there wasn't another skb ready to transmit immediately, this led to a
double-free because we'd free it *again* next time we did have a packet to
send.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some MSI laptop BIOSes are broken - INT 15h code uses port 92h to enable A20
line but resume code assumes that KBC was used.
The laptop will not resume from S3 otherwise but powers off after a while
and then powers on again stuck with a blank screen.
Fix it by enabling A20 using KBC in i8042_platform_init for x86.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Rafael J. Wysocki <rjw@sisk.pl> Link: http://lkml.kernel.org/r/201212112218.06551.linux@rainbow-software.org Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
dmapool always calls dma_alloc_coherent() with GFP_ATOMIC flag,
regardless the flags provided by the caller. This causes excessive
pruning of emergency memory pools without any good reason. Additionaly,
on ARM architecture any driver which is using dmapools will sooner or
later trigger the following error:
"ERROR: 256 KiB atomic DMA coherent pool is too small!
Please increase it with coherent_pool= kernel parameter!".
Increasing the coherent pool size usually doesn't help much and only
delays such error, because all GFP_ATOMIC DMA allocations are always
served from the special, very limited memory pool.
This patch changes the dmapool code to correctly use gfp flags provided
by the dmapool caller.
Reported-by: Soeren Moch <smoch@web.de> Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Soeren Moch <smoch@web.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This can lead to a panic if the driver isn't ready to
handle them. Since our interrupt line is shared, we can get
an interrupt at any time (and CONFIG_DEBUG_SHIRQ checks
that even when the interrupt is being freed).
If the op_mode has gone away, we musn't call it. To avoid
this the transport disables the interrupts when the hw is
stopped and the op_mode is leaving.
If there is an event that would cause an interrupt the INTA
register is updated regardless of the enablement of the
interrupts: even if the interrupts are disabled, the INTA
will be changed, but the device won't issue an interrupt.
But the ISR can be called at any time, so we ought ignore
the value in the INTA otherwise we can call the op_mode
after it was freed.
I found this bug when the op_mode_start failed, and called
iwl_trans_stop_hw(trans, true). Then I played with the
RFKILL button, and removed the module.
While removing the module, the IRQ is freed, and the ISR is
called (CONFIG_DEBUG_SHIRQ enabled). Panic.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2:
- Adjust context
- Pass bus(trans), not trans, to iwl_{read,write}32()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
With NFSv4, if we create a file then open it we explicit avoid checking
the permissions on the file during the open because the fact that we
created it ensures we should be allow to open it (the create and the
open should appear to be a single operation).
However if the reply to an EXCLUSIVE create gets lots and the client
resends the create, the current code will perform the permission check -
because it doesn't realise that it did the open already..
This patch should fix this.
Note that I haven't actually seen this cause a problem. I was just
looking at the code trying to figure out a different EXCLUSIVE open
related issue, and this looked wrong.
(Fix confirmed with pynfs 4.0 test OPEN4--bfields)
Signed-off-by: NeilBrown <neilb@suse.de>
[bfields: use OWNER_OVERRIDE and update for 4.1] Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[bwh: Backported to 3.2:
- Adjust context
- Use current_fh as file handle in do_open_lookup()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
drm/i915: set phase sync pointer override enable before setting phase sync pointer
It turns out that this w/a isn't actually required on cpt/ppt and
positively harmful on ivb/ppt when using fdi B/C links - it results in
a black screen occasionally, with seemingfully everything working as
it should. The only failure indication I've found in the hw is that
eventually (but not right after the modeset completes) a pipe underrun
is signalled.
Big thanks to Arthur Runyan for all the ideas for registers to check
and changes to test, otherwise I couldn't ever have tracked this down!
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
They are all written for a specific north disaplay->pch combination.
So stop pretending otherwise.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.
Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.
Factor in the 6db offset when converting internal noisefloor to channel noise.
This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.
Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The cause of the error is that the OTP register
offsets are different on the AR9340 than the
actually used values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Turns out reverting commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd
"ath9k_hw: Updated AR9003 tx gain table for 5GHz" was not enough to
bring the tx power back to normal levels on devices like the
Buffalo WZR-HP-G450H, this one needs to be reverted as well.
This revert improves tx power by ~10 db on that device
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: rmanohar@qca.qualcomm.com Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If count is less than the size of a register then we may hit integer
wraparound when trying to move backwards to check if we're still in
the buffer. Instead move the position forwards to check if it's still
in the buffer, we are unlikely to be able to allocate a buffer
sufficiently big to overflow here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[bwh: Backported to 3.2: formatted length is tot_len] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: use pll->flags instead of radeon_crtc->pll_flags] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: drop the ASIC_IS_DCE61() case] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[akpm@linux-foundation.org: return false for '@' as well, per Bjorn] Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch changes vectored file I/O to use kmap + kunmap when mapping
incoming SGL memory -> struct iovec in order to properly support 32-bit
highmem configurations. This is because an extra bounce buffer may be
required when processing scatterlist pages allocated with GFP_KERNEL.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: use task->task_sg{,_nents} for iteration] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Or else the laptop will boot with a dimmed screen.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51141 Tested-by: Stefan Nagy <public@stefan-nagy.at> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added
the support of autopm for USB MIDI output, but it didn't take the MIDI
input into account.
This patch adds the following for fixing the autopm:
- Manage the URB start at the first MIDI input stream open, instead of
the time of instance creation
- Move autopm code to the common substream_open()
- Make snd_usbmidi_input_start/_stop() more robust and add the running
state check
Reviewd-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add a similar protection against the disconnection race and the
invalid use of usb instance after disconnection, as well as we've done
for the USB audio PCM.
The check to whom a device is reserved is done by checking the path
state of the affected channel paths. If it turns out that one path is
flagged as reserved by someone else the whole device is marked as such.
However the meaning of the RESVD_ELSE bit is that the addressed device
is reserved to a different pathgroup (and not reserved to a different
LPAR). If we do this test on a path which is currently not a member of
the pathgroup we could erroneously mark the device as reserved to
someone else.
To fix this collect the reserved state for all potential members of the
pathgroup and only mark the device as reserved if all of those potential
members have the RESVD_ELSE bit set.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ata_device->dma_mode's initial value is zero, which is not a valid dma
mode, but ata_dma_enabled will return true for this value. This patch
sets dma_mode to 0xff in reset function, so that ata_dma_enabled will
not return true for this case, or it will cause problem for pata_acpi.
The corrsponding bugzilla page is at:
https://bugzilla.kernel.org/show_bug.cgi?id=49151
Reported-by: Phillip Wood <phillip.wood@dunelm.org.uk> Signed-off-by: Aaron Lu <aaron.lu@intel.com> Tested-by: Szymon Janc <szymon@janc.net.pl> Tested-by: Dutra Julio <dutra.julio@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 0a97e1e9f9a6 ('HID: apple: Add Apple wireless keyboard 2011 ANSI PID')
did not update the special driver list in hid-core.c, so hid-generic may
still bind to this device.
Reported-by: Ari Pollak <ari@scvngr.com>
References: http://bugs.debian.org/694546 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alexey Kaminsky <me@akaminsky.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bwh: Backported to 3.2: add the device ID to hid-ids.h] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes both the transmit and receive portion of sending
fragmented mutlicast and broadcast packets.
The transmit section was broken because the offset for INTFRAG and
LASTFRAG packets were just miscalculated by IEEE1394_GASP_HDR_SIZE (which
was reserved with skb_push() in fwnet_send_packet).
The receive section was broken because in fwnet_incoming_packet is a call
to fwnet_peer_find_by_node_id(). Called with generation == -1 it will
not find a peer and the partial datagrams are associated to a peer.
[Stefan R: The fix to use context->card->generation is not perfect.
It relies on the IR tasklet which processes packets from the prior bus
generation to run before the self-ID-complete worklet which sets the
current card generation. Alas, there is no simple way of a race-free
implementation. Let's do it this way for now.]
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The function rb_set_head_page() searches the list of ring buffer
pages for a the page that has the HEAD page flag set. If it does
not find it, it will do a WARN_ON(), disable the ring buffer and
return NULL, as this should never happen.
But if this bug happens to happen, not all callers of this function
can handle a NULL pointer being returned from it. That needs to be
fixed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
During resume from system suspend the 'data' field of
struct pnp_dev in pnpacpi_set_resources() may be a stale pointer,
due to removal of the associated ACPI device node object in the
previous suspend-resume cycle. This happens, for example, if a
dockable machine is booted in the docking station and then suspended
and resumed and suspended again. If that happens,
pnpacpi_build_resource_template() called from pnpacpi_set_resources()
attempts to use that pointer and crashes.
However, pnpacpi_set_resources() actually checks the device's ACPI
handle, attempts to find the ACPI device node object attached to it
and returns an error code if that fails, so in fact it knows what the
correct value of dev->data should be. Use this observation to update
dev->data with the correct value if necessary and dump a call trace
if that's the case (once).
We still need to fix the root cause of this issue, but preventing
systems from crashing because of it is an improvement too.
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51071 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ACPI video driver can't control backlight correctly on
Asus UL30VT. Vendor driver (asus-laptop) can work. This patch is to
add "Asus UL30VT" to ACPI video detect blacklist in order to use
asus-laptop for video control on the "Asus UL30VT" rather than ACPI
video driver.
References: https://bugzilla.kernel.org/show_bug.cgi?id=32592 Reported-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On Samsung X360, the BIOS will set a flag (VDRV) if the generic
ACPI backlight device is used. This flag will definitively break
the backlight interface (even the vendor interface) untill next
reboot. It's why we should prevent video.ko from being used here
and we can't rely on a later call to acpi_video_unregister().
Signed-off-by: Corentin Chary <corentin.chary@gmail.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The current acpisleep DMI checks only run when CONFIG_SUSPEND is set.
And this may break hibernation on some platforms when CONFIG_SUSPEND
is cleared.
Move acpisleep DMI check into #ifdef CONFIG_ACPI_SLEEP instead.
[rjw: Added acpi_sleep_dmi_check() and rebased on top of earlier
patches adding entries to acpisleep_dmi_table[].]
References: https://bugzilla.kernel.org/show_bug.cgi?id=45921 Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When the qla2xxx driver loses access to multiple, remote ports, there is a race
condition which can occur which will keep the request stuck on a scsi request
queue indefinitely.
This bad state occurred do to a race condition with how the FCPORT_UPDATE_NEEDED
bit is set in qla2x00_schedule_rport_del(), and how it is cleared in
qla2x00_do_dpc(). The problem port has its drport pointer set, but it has never
been processed by the driver to inform the fc transport that the port has been
lost. qla2x00_schedule_rport_del() sets drport, and then sets the
FCPORT_UPDATE_NEEDED bit. In qla2x00_do_dpc(), the port lists are walked and
any drport pointer is handled and the fc transport informed of the port loss,
then the FCPORT_UPDATE_NEEDED bit is cleared. This leaves a race where the
dpc thread is processing one port removal, another port removal is marked
with a call to qla2x00_schedule_rport_del(), and the dpc thread clears the
bit for both removals, even though only the first removal was actually
handled. Until another event occurs to set FCPORT_UPDATE_NEEDED, the later
port removal is never finished and qla2xxx stays in a bad state which causes
requests to become stuck on request queues.
This patch updates the driver to test and clear FCPORT_UPDATE_NEEDED
atomically. This ensures the port state changes are processed and not lost.
Signed-off-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / karo-tx-linux.git / log