Jarod Wilson [Fri, 21 Oct 2016 03:25:27 +0000 (23:25 -0400)]
net: remove MTU limits on a few ether_setup callers
These few drivers call ether_setup(), but have no ndo_change_mtu, and thus
were overlooked for changes to MTU range checking behavior. They
previously had no range checks, so for feature-parity, set their min_mtu
to 0 and max_mtu to ETH_MAX_MTU (65535), instead of the 68 and 1500
inherited from the ether_setup() changes. Fine-tuning can come after we get
back to full feature-parity here.
CC: netdev@vger.kernel.org Reported-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st> CC: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st> CC: R Parameswaran <parameswaran.r7@gmail.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Wed, 19 Oct 2016 13:53:01 +0000 (15:53 +0200)]
hv_netvsc: fix a race between netvsc_send() and netvsc_init_buf()
Fix in commit 880988348270 ("hv_netvsc: set nvdev link after populating
chn_table") turns out to be incomplete. A crash in
netvsc_get_next_send_section() is observed on mtu change when the device
is under load. The race I identified is: if we get to netvsc_send() after
we set net_device_ctx->nvdev link in netvsc_device_add() but before we
finish netvsc_connect_vsp()->netvsc_init_buf() send_section_map is not
allocated and we crash. Unfortunately we can't set net_device_ctx->nvdev
link after the netvsc_init_buf() call as during the negotiation we need
to receive packets and on the receive path we check for it. It would
probably be possible to split nvdev into a pair of nvdev_in and nvdev_out
links and check them accordingly in get_outbound_net_device()/
get_inbound_net_device() but this looks like an overkill.
Check that send_section_map is allocated in netvsc_send().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Oct 2016 18:51:11 +0000 (14:51 -0400)]
Merge branch 'MTU-core-range-checking-more'
Jarod Wilson says:
====================
net: use core MTU range checking everywhere
This stack of patches should get absolutely everything in the kernel
converted from doing their own MTU range checking to the core MTU range
checking. This second spin includes alterations to hopefully fix all
concerns raised with the first, as well as including some additional
changes to drivers and infrastructure where I completely missed necessary
updates.
These have all been built through the 0-day build infrastructure via the
(rebasing) master branch at https://github.com/jarodwilson/linux-muck, which
at the time of the most recent compile across 147 configs, was based on
net-next at commit 7b1536ef0aa0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org CC: "David S. Miller" <davem@davemloft.net> CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> CC: James Morris <jmorris@namei.org> CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:23 +0000 (13:55 -0400)]
s390/net: use net core MTU range checking
ctcm:
- min_mtu = 576, max_mtu = 65527
netiucv:
- min_mtu = 576, max_mtu = 65535
qeth:
- min_mtu = 64, max_mtu = 65535
CC: netdev@vger.kernel.org CC: linux-s390@vger.kernel.org CC: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:22 +0000 (13:55 -0400)]
net: use core MTU range checking in misc drivers
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
Jarod Wilson [Thu, 20 Oct 2016 17:55:20 +0000 (13:55 -0400)]
net: use core MTU range checking in core net infra
geneve:
- Merge __geneve_change_mtu back into geneve_change_mtu, set max_mtu
- This one isn't quite as straight-forward as others, could use some
closer inspection and testing
macvlan:
- set min/max_mtu
tun:
- set min/max_mtu, remove tun_net_change_mtu
vxlan:
- Merge __vxlan_change_mtu back into vxlan_change_mtu
- Set max_mtu to IP_MAX_MTU and retain dynamic MTU range checks in
change_mtu function
- This one is also not as straight-forward and could use closer inspection
and testing from vxlan folks
bridge:
- set max_mtu of IP_MAX_MTU and retain dynamic MTU range checks in
change_mtu function
openvswitch:
- set min/max_mtu, remove internal_dev_change_mtu
- note: max_mtu wasn't checked previously, it's been set to 65535, which
is the largest possible size supported
sch_teql:
- set min/max_mtu (note: max_mtu previously unchecked, used max of 65535)
macsec:
- min_mtu = 0, max_mtu = 65535
macvlan:
- min_mtu = 0, max_mtu = 65535
ntb_netdev:
- min_mtu = 0, max_mtu = 65535
veth:
- min_mtu = 68, max_mtu = 65535
8021q:
- min_mtu = 0, max_mtu = 65535
CC: netdev@vger.kernel.org CC: Nicolas Dichtel <nicolas.dichtel@6wind.com> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Tom Herbert <tom@herbertland.com> CC: Daniel Borkmann <daniel@iogearbox.net> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: Paolo Abeni <pabeni@redhat.com> CC: Jiri Benc <jbenc@redhat.com> CC: WANG Cong <xiyou.wangcong@gmail.com> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Pravin B Shelar <pshelar@ovn.org> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Patrick McHardy <kaber@trash.net> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Pravin Shelar <pshelar@nicira.com> CC: Maxim Krasnyansky <maxk@qti.qualcomm.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:19 +0000 (13:55 -0400)]
net: use core MTU range checking in WAN drivers
- set min/max_mtu in all hdlc drivers, remove hdlc_change_mtu
- sent max_mtu in lec driver, remove lec_change_mtu
- set min/max_mtu in x25_asy driver
CC: netdev@vger.kernel.org CC: Krzysztof Halasa <khc@pm.waw.pl> CC: Krzysztof Halasa <khalasa@piap.pl> CC: Jan "Yenya" Kasprzak <kas@fi.muni.cz> CC: Francois Romieu <romieu@fr.zoreil.com> CC: Kevin Curtis <kevin.curtis@farsite.co.uk> CC: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:18 +0000 (13:55 -0400)]
net: use core MTU range checking in wireless drivers
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: Maya Erez <qca_merez@qca.qualcomm.com> CC: Simon Kelley <simon@thekelleys.org.uk> CC: Stanislav Yakovlev <stas.yakovlev@gmail.com> CC: Johannes Berg <johannes@sipsolutions.net> CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:17 +0000 (13:55 -0400)]
net: use core MTU range checking in USB NIC drivers
usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
max_mtu and/or min_mtu as needed)
r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)
lan78xx:
- Set max_mtu = 9000
asix_driver:
- max_mtu = 16384 for ax88178 variant
ax88179:
- max_mtu = 4088
cdc_ncm:
- max_mtu from hardware
cdc-phonet:
- min_mtu = 6, max_mtu = 65541
sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
usbnet_change_mtu, but if we set max_mtu to let the network core handle
the range check, then we can simply call usbnet_change_mtu directly
smsc75xx:
- max_mtu = 9000
CC: netdev@vger.kernel.org CC: Woojung Huh <woojung.huh@microchip.com> CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> CC: Hayes Wang <hayeswang@realtek.com> CC: Oliver Neukum <oneukum@suse.com> CC: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Thu, 20 Oct 2016 17:55:16 +0000 (13:55 -0400)]
ethernet: use net core MTU range checking in more drivers
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") CC: netdev@vger.kernel.org CC: Jes Sorensen <jes@trained-monkey.org> CC: Netanel Belgazal <netanel@annapurnalabs.com> CC: Tom Lendacky <thomas.lendacky@amd.com> CC: Santosh Raspatur <santosh@chelsio.com> CC: Hariprasad S <hariprasad@chelsio.com> CC: Sathya Perla <sathya.perla@broadcom.com> CC: Ajit Khaparde <ajit.khaparde@broadcom.com> CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> CC: Somnath Kotur <somnath.kotur@broadcom.com> CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> CC: John Allen <jallen@linux.vnet.ibm.com> CC: Guo-Fu Tseng <cooldavid@cooldavid.org> CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> CC: Jiri Pirko <jiri@mellanox.com> CC: Ido Schimmel <idosch@mellanox.com> CC: Manish Chopra <manish.chopra@qlogic.com> CC: Sony Chacko <sony.chacko@qlogic.com> CC: Rajesh Borundia <rajesh.borundia@qlogic.com> CC: Timur Tabi <timur@codeaurora.org> CC: Anirudha Sarangi <anirudh@xilinx.com> CC: John Linn <John.Linn@xilinx.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 20 Oct 2016 17:00:32 +0000 (17:00 +0000)]
net: ethernet: mediatek: use dev_kfree_skb_any instead of dev_kfree_skb
Replace dev_kfree_skb with dev_kfree_skb_any in mtk_start_xmit()
which can be called from hard irq context (netpoll) and from
other contexts. mtk_start_xmit() only frees skbs that it has
dropped.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Thu, 20 Oct 2016 16:59:49 +0000 (16:59 +0000)]
dwc_eth_qos: use dev_kfree_skb_any instead of dev_kfree_skb
Replace dev_kfree_skb with dev_kfree_skb_any in dwceqos_start_xmit()
which can be called from hard irq context (netpoll) and from
other contexts. dwceqos_start_xmit() only frees skbs that it has
dropped.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Thu, 20 Oct 2016 08:28:27 +0000 (10:28 +0200)]
net: fec: drop check for clk==NULL before calling clk_*
clk_prepare, clk_enable and their counterparts (at least the common clk
ones, but also most others) do check for the clk being NULL anyhow (and
return 0 then), so there is no gain when the caller checks, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 20 Oct 2016 04:24:58 +0000 (21:24 -0700)]
tcp: relax listening_hash operations
softirq handlers use RCU protection to lookup listeners,
and write operations all happen from process context.
We do not need to block BH for dump operations.
Also SYN_RECV since request sockets are stored in the ehash table :
1) inet_diag_dump_icsk() no longer need to clear
cb->args[3] and cb->args[4] that were used as cursors while
iterating the old per listener hash table.
2) Also factorize a test : No need to scan listening_hash[]
if r->id.idiag_dport is not zero.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Wed, 19 Oct 2016 21:23:50 +0000 (23:23 +0200)]
net: smc91x: fix neponset breakage by pxa u16 writes
The patch isolating the u16 writes for pxa assumed all machine_is_*()
calls were removed, and therefore removed the mach-types.h include which
provided them.
Unfortunately 2 machine_is_*() remained in smc91x.c file including
smc91x.h from which the include was removed, triggering the error:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_drv_probe’:
drivers/net/ethernet/smsc/smc91x.c:2380:2: error: implicit declaration
of function ‘machine_is_assabet’
[-Werror=implicit-function-declaration]
if (machine_is_assabet() && machine_has_neponset())
This adds back the wrongly removed include.
Fixes: d09d747ae4c2 ("net: smc91x: isolate u16 writes alignment workaround") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 65d7ab8de582 ("net: Identifier Locator Addressing module") Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Oct 2016 19:18:21 +0000 (15:18 -0400)]
Merge branch 'macb-ethtool-ringparam'
Zach Brown says:
====================
macb: Add ethtool get_ringparam and set_ringparam to cadence
There are use cases like RT that would benefit from being able to tune the
macb rx/tx ring sizes. The ethtool set_ringparam function is the standard way
of doing so.
The first patch changes the hardcoded tx/rx ring sizes to variables that are
set to a hardcoded default.
The second patch implements the get_ringparam and set_ringparam fucntions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zach Brown [Wed, 19 Oct 2016 14:56:57 +0000 (09:56 -0500)]
net: macb: Use variables with defaults for tx/rx ring sizes instead of hardcoded values
The macb driver hardcoded the tx/rx ring sizes. This made it
impossible to change the sizes at run time.
Add tx_ring_size, and rx_ring_size variables to macb object, which
are initilized with default vales during macb_init. Change all
references to RX_RING_SIZE and TX_RING_SIZE to their respective
replacements.
Signed-off-by: Zach Brown <zach.brown@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 19 Oct 2016 13:47:52 +0000 (13:47 +0000)]
net: arc_emac: use dev_kfree_skb_any instead of dev_kfree_skb
Replace dev_kfree_skb with dev_kfree_skb_any in arc_emac_tx()
which can be called from hard irq context (netpoll) and from
other contexts. arc_emac_tx() only frees skbs that it has
dropped.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A BPF program is required to check the return register of a
map_elem_lookup() call before accessing memory. The verifier keeps
track of this by converting the type of the result register from
PTR_TO_MAP_VALUE_OR_NULL to PTR_TO_MAP_VALUE after a conditional
jump ensures safety. This check is currently exclusively performed
for the result register 0.
In the event the compiler reorders instructions, BPF_MOV64_REG
instructions may be moved before the conditional jump which causes
them to keep their type PTR_TO_MAP_VALUE_OR_NULL to which the
verifier objects when the register is accessed:
This commit extends the verifier to keep track of all identical
PTR_TO_MAP_VALUE_OR_NULL registers after a map_elem_lookup() by
assigning them an ID and then marking them all when the conditional
jump is observed.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Reviewed-by: Josef Bacik <jbacik@fb.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Wed, 19 Oct 2016 09:24:57 +0000 (11:24 +0200)]
net: fs_enet: Use net_device_stats from struct net_device
Instead of using a private copy of struct net_device_stats in struct
fs_enet_private, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 18:14:22 +0000 (14:14 -0400)]
Merge branch 'smc91x-dt'
Robert Jarzmik says:
====================
support smc91x on mainstone and devicetree
This series aims at bringing support to mainstone board on a
device-tree based build, as what is already in place for legacy
mainstone.
The bulk of the mainstone "specific" behavior is that a u16 write
doesn't work on a address of the form 4*n + 2, while it works on 4*n.
The legacy workaround was in SMC_outw(), with calls to
machine_is_mainstone(). These calls don't work with a pxa27x-dt
machine type, which is used when a generic device-tree pxa27x machine
is used to boot the mainstone board.
Therefore, this series enables the smc91c111 adapter of the mainstone
board to work on a device-tree build, exaclty as it's been working for
years with the legacy arch/arm/mach-pxa/mainstone.c definition.
As a sum up, this extends an existing mechanism to device-tree based
pxa platforms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Mon, 17 Oct 2016 19:45:32 +0000 (21:45 +0200)]
net: smsc91x: add u16 workaround for pxa platforms
Add a workaround for mainstone, idp and stargate2 boards, for u16 writes
which must be aligned on 32 bits addresses.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Jeremy Linton <jeremy.linton@arm.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Mon, 17 Oct 2016 19:45:31 +0000 (21:45 +0200)]
net: smc91x: take into account half-word workaround
For device-tree builds, platforms such as mainstone, idp and stargate2
must have their u16 writes all aligned on 32 bit boundaries. This is
already enabled in platform data builds, and this patch adds it to
device-tree builds.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Writes to u16 has a special handling on 3 PXA platforms, where the
hardware wiring forces these writes to be u32 aligned.
This patch isolates this handling for PXA platforms as before, but
enables this "workaround" to be set up dynamically, which will be the
case in device-tree build types.
This patch was tested on 2 PXA platforms : mainstone, which relies on
the workaround, and lubbock, which doesn't.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Tue, 18 Oct 2016 16:47:45 +0000 (17:47 +0100)]
ethernet/sfc: use core min/max MTU checking
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 15:56:31 +0000 (11:56 -0400)]
Merge branch 'phy-led-triggers'
Zach Brown says:
====================
Add support for led triggers on phy link state change
Fix skge driver that declared enum contants that conflicted with enum
constants in linux/leds.h
Create function that encapsulates actions taken during the adjust phy link step
of phy state changes.
Create function that provides list of speeds currently supported by the phy.
Add support for led triggers on phy link state changes by adding
a config option. When set the config option will create a set of led triggers
for each phy device. Users can use the led triggers to represent link state
changes on the phy.
v2:
* New patch that creates phy_adjust_link function to encapsulate actions taken
when adjusting phy link during phy state changes
* led trigger speed strings changed to match existing phy speed strings
* New function that maps speeds to led triggers
* Replace magic constants with definitions when declaring trigger name
buffer and number of triggers.
v3:
* Changed LED_ON to LED_REG_ON in skge driver to avoid possible future
conflict and improve consistency.
* Dropped rtl8712 patch that was accepted separately.
v4:
* tweaked commit message
v5
* Changed commit message to explain relationship between the new triggers and
leds driven by phys.
* Added new patch that creates phy_supported_speeds function.
* Moved phy_leds_triggers_register and phy_leds_triggers_unregister to
phy_attach and phy_detach respectively. This change is so the
phydev->supported field will be filled by the time the triggers are
registered.
* Changed hardcoded list of triggers to dynamic list determined by speeds
return by phy_supported_speeds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zach Brown [Mon, 17 Oct 2016 15:49:55 +0000 (10:49 -0500)]
net: phy: leds: add support for led triggers on phy link state change
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: Zach Brown <zach.brown@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zach Brown [Mon, 17 Oct 2016 15:49:53 +0000 (10:49 -0500)]
net: phy: Encapsulate actions performed during link state changes into function phy_adjust_link
During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function
This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.
Signed-off-by: Zach Brown <zach.brown@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zach Brown [Mon, 17 Oct 2016 15:49:52 +0000 (10:49 -0500)]
skge: Rename LED_OFF and LED_ON in marvel skge driver to avoid conflicts with leds namespace
Adding led support for phy causes namespace conflicts for some
phy drivers.
The marvel skge driver declared an enum for representing the states of
Link LED Register. The enum contained constant LED_OFF which conflicted
with declartation found in linux/leds.h.
LED_OFF changed to LED_REG_OFF
Also changed LED_ON to LED_REG_ON to avoid possible future conflict and
for consistency.
Signed-off-by: Zach Brown <zach.brown@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the BUG is converted to a WARN_ON it shows 4 missing adjacencies:
eth3 - myvrf, mvrf - eth3, bond1 - myvrf and myvrf - bond1
All of those are because the __netdev_upper_dev_link function does not
properly link macvlan lower devices to myvrf when it is enslaved.
The second case just flips the ordering of the enslavements:
ip link set bond1 master bridge
ip link set macvlan master myvrf
Then run:
ip link delete bond1
ip link delete myvrf
The vrf delete command hangs because myvrf has a reference that has not
been released. In this case the removal code does not account for 2 paths
between eth3 and myvrf - one from bridge to vrf and the other through the
macvlan.
Rather than try to maintain a linked list of all upper and lower devices
per netdevice, only track the direct neighbors. The remaining stack can
be determined by recursively walking the neighbors.
The existing netdev_for_each_all_upper_dev_rcu,
netdev_for_each_all_lower_dev and netdev_for_each_all_lower_dev_rcu macros
are replaced with APIs that walk the upper and lower device lists. The
new APIs take a callback function and a data arg that is passed to the
callback for each device in the list. Drivers using the old macros are
converted in separate patches to make it easier on reviewers. It is an
API conversion only; no functional change is intended.
v3
- address Stephen's comment to simplify logic and remove typecasts
v2
- fixed bond0 references in cover-letter
- fixed definition of netdev_next_lower_dev_rcu to mirror the upper_dev
version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:53 +0000 (19:15 -0700)]
net: dev: Improve debug statements for adjacency tracking
Adjacency code only has debugs for the insert case. Add debugs for
the remove path and make both consistently worded to make it easier
to follow the insert and removal with reference counts.
In addition, change the BUG to a WARN_ON. A missing adjacency at
removal time is not cause for a panic.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:51 +0000 (19:15 -0700)]
net: Remove all_adj_list and its references
Only direct adjacencies are maintained. All upper or lower devices can
be learned via the new walk API which recursively walks the adj_list for
upper devices or lower devices.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:46 +0000 (19:15 -0700)]
IB/core: Flip to the new dev walk API
Convert rdma_is_upper_dev_rcu, handle_netdev_upper and
ipoib_get_net_dev_match_addr to the new upper device walk API.
This is just a code conversion; no functional change is intended.
v2
- removed typecast of data
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:45 +0000 (19:15 -0700)]
net: bonding: Flip to the new dev walk API
Convert alb_send_learning_packets and bond_has_this_ip to use the new
netdev_walk_all_upper_dev_rcu API. In both cases this is just a code
conversion; no functional change is intended.
v2
- removed typecast of data and simplified bond_upper_dev_walk
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:44 +0000 (19:15 -0700)]
net: Introduce new api for walking upper and lower devices
This patch introduces netdev_walk_all_upper_dev_rcu,
netdev_walk_all_lower_dev and netdev_walk_all_lower_dev_rcu. These
functions recursively walk the adj_list of devices to determine all upper
and lower devices.
The functions take a callback function that is invoked for each device
in the list. If the callback returns non-0, the walk is terminated and
the functions return that code back to callers.
v3
- simplified netdev_has_upper_dev_all_rcu and __netdev_has_upper_dev and
removed typecast as suggested by Stephen
v2
- fixed definition of netdev_next_lower_dev_rcu to mirror the upper_dev
version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 18 Oct 2016 02:15:43 +0000 (19:15 -0700)]
net: Remove refnr arg when inserting link adjacencies
Commit 93409033ae65 ("net: Add netdev all_adj_list refcnt propagation to
fix panic") propagated the refnr to insert and remove functions tracking
the netdev adjacency graph. However, for the insert path the refnr can
only be 1. Accordingly, remove the refnr argument to make that clear.
ie., the refnr arg in 93409033ae65 was only needed for the remove path.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 15:35:55 +0000 (11:35 -0400)]
Merge branch 'bpf-selftests'
Daniel Borkmann says:
====================
Move to BPF selftests
This set improves the test_verifier and test_maps suite and moves
it over to a new BPF selftest directory, so we can keep improving
it under kernel selftest umbrella. This also integrates a test
script for checking test_bpf.ko under various JIT options.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 17 Oct 2016 12:28:36 +0000 (14:28 +0200)]
bpf: add initial suite for selftests
Add a start of a test suite for kernel selftests. This moves test_verifier
and test_maps over to tools/testing/selftests/bpf/ along with various
code improvements and also adds a script for invoking test_bpf module.
The test suite can simply be run via selftest framework, f.e.:
# cd tools/testing/selftests/bpf/
# make
# make run_tests
Both test_verifier and test_maps were kind of misplaced in samples/bpf/
directory and we were looking into adding them to selftests for a while
now, so it can be picked up by kbuild bot et al and hopefully also get
more exposure and thus new test case additions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 17 Oct 2016 12:28:35 +0000 (14:28 +0200)]
bpf: add various tests around spill/fill of regs
Add several spill/fill tests. Besides others, one that performs xadd
on the spilled register, one ldx/stx test where different types are
spilled from two branches and read out from common path. Verfier does
handle all correctly.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 15:34:22 +0000 (11:34 -0400)]
Merge branch 'ethernet-use-core-min-max-mtu'
Jarod Wilson says:
====================
ethernet: use core min/max MTU checking
Now that the network stack core min/max MTU checking infrastructure is in
place, time to start making drivers use it. We'll start with the easiest
ones, the ethernet drivers, split roughly by vendor, with a catch-all
patch at the end.
For the most part, every patch does the same essential thing: removes the
MTU range checking from the drivers' ndo_change_mtu function, puts those
ranges into the core net_device min_mtu and max_mtu fields, and where
possible, removes ndo_change_mtu functions entirely.
These patches have all been built through the 0-day build infrastructure
provided by Intel, on top of net-next as of October 17.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:16 +0000 (15:54 -0400)]
ethernet/toshiba: use core min/max MTU checking
gelic_net: min_mtu 64, max_mtu 1518
- remove gelic_net_change_mtu now that it is redundant
spidernet: min_Mtu 64, max_mtu 2294
- remove spiter_net_change_mtu now that it is redundant
CC: netdev@vger.kernel.org CC: Geoff Levand <geoff@infradead.org> CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:15 +0000 (15:54 -0400)]
ethernet/tile: use core min/max MTU checking
tilegx: min_mtu 68, max_mtu 1500 or 9000, depending on modparam
- remove tile_net_change_mtu now that it is fully redundant
tilepro: min_mtu 68, max_mtu 1500
- hardware supports jumbo packets up to 10226, but it's not implemented or
tested yet, according to code comments
CC: netdev@vger.kernel.org CC: Chris Metcalf <cmetcalf@mellanox.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
emac: min_mtu 46, max_mtu 1500 or whatever gets read from OF
CC: netdev@vger.kernel.org CC: Douglas Miller <dougmill@linux.vnet.ibm.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:12 +0000 (15:54 -0400)]
ethernet/neterion: use core min/max MTU checking
s2io: min_mtu 46, max_mtu 9600
vxge: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org CC: Jon Mason <jdmason@kudzu.us> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:11 +0000 (15:54 -0400)]
ethernet/dlink: use core min/max MTU checking
dl2k: min_mtu 68, max_mtu 1536 or 8000, depending on hardware
- Removed change_mtu, does nothing productive anymore
sundance: min_mtu 68, max_mtu 8191
CC: netdev@vger.kernel.org CC: Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:09 +0000 (15:54 -0400)]
ethernet/realtek: use core min/max MTU checking
8139cp: min_mtu 60, max_mtu 4096
8139too: min_mtu 68, max_mtu 1770
r8169: min_mtu 60, max_mtu depends on chipset, 1500 to 9k-ish
CC: netdev@vger.kernel.org CC: Realtek linux nic maintainers <nic_swsd@realtek.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:08 +0000 (15:54 -0400)]
ethernet/qlogic: use core min/max MTU checking
qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h
qlcnic: min_mtu 68, max_mtu 9600
CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com CC: Yuval Mintz <Yuval.Mintz@qlogic.com> CC: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:07 +0000 (15:54 -0400)]
ethernet/mellanox: use core min/max MTU checking
mlx4: min_mtu 46, max_mtu depends on hardware
mlx5: min_mtu 68, max_mtu depends on hardware
CC: netdev@vger.kernel.org CC: Tariq Toukan <tariqt@mellanox.com> CC: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:06 +0000 (15:54 -0400)]
ethernet/marvell: use core min/max MTU checking
mvneta: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvneta_change_mtu for simplicity
mvpp2: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
mvpp2_change_mtu for simplicity
pxa168_eth: min_mtu 68, max_mtu 9500
skge: min_mtu 60, max_mtu 9000
sky2: min_mtu 68, max_mtu 1500 or 9000, depending on hw
CC: netdev@vger.kernel.org CC: Mirko Lindner <mlindner@marvell.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:05 +0000 (15:54 -0400)]
ethernet/intel: use core min/max MTU checking
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org CC: intel-wired-lan@lists.osuosl.org CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Mon, 17 Oct 2016 19:54:03 +0000 (15:54 -0400)]
ethernet/atheros: use core min/max MTU checking
atl2: min_mtu 40, max_mtu 1504
- Remove a few redundant defines that already have equivalents in
if_ether.h.
atl1: min_mtu 42, max_mtu 10218
atl1e: min_mtu 42, max_mtu 8170
atl1c: min_mtu 42, max_mtu 6122/1500
- GbE hardware gets a max_mtu of 6122, slower hardware gets 1500.
alx: min_mtu 34, max_mtu 9256
- Not so sure that minimum MTU number is really what was intended, but
that's what the math actually makes it out to be, due to max_frame
manipulations and comparison in alx_change_mtu, rather than just
comparing new_mtu. (I think 68 was the intended min_mtu value).
CC: netdev@vger.kernel.org CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 14:42:17 +0000 (10:42 -0400)]
Merge branch 'dp83867-impedance-control'
Mugunthan V N says:
====================
add support for impedance control for TI dp83867 phy and fix 2nd ethernet on dra72 rev C evm
Add support for configurable impedance control for TI dp83867
phy via devicetree. More documentation in [1].
CPSW second ethernet is not working, fix it by enabling
impedance configuration on the phy.
Verified the patch on DRA72 Rev C evm, logs at [2]. Also pushed
a branch [3] for others to test.
Changes from v3:
* Fixup change log text and no code changes.
Changes from v2:
* Fixed a typo in dts and driver.
Changes from initial version:
* As per Sekhar's comment, instead of passing impedance values,
change to max and min impedance from DT
* Adopted phy_read_mmd_indirect() to cunnrent implementation.
* Corrected the phy delay timings to the optimal value.
The default impedance settings of the phy is not the optimal
value, due to this the second ethernet is not working. Fix it
with correct values which makes the second ethernet port to work.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Tue, 18 Oct 2016 11:20:17 +0000 (16:50 +0530)]
net: phy: dp83867: Add documentation for optional impedance control
Add documention of ti,min-output-impedance and ti,max-output-impedance
which can be used to correct MAC impedance mismatch using phy extended
registers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 18 Oct 2016 06:44:17 +0000 (08:44 +0200)]
vlan: Remove unnecessary comparison of unsigned against 0
args.u.name_type is of type unsigned int and is always >= 0.
This fixes the following GCC warning:
net/8021q/vlan.c: In function ‘vlan_ioctl_handler’:
net/8021q/vlan.c:574:14: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 17 Oct 2016 15:19:56 +0000 (15:19 +0000)]
fsl/fman: fix error return code in mac_probe()
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 17 Oct 2016 14:30:57 +0000 (16:30 +0200)]
fjes: fix format string for trace output
phys_addr_t may be wider than a pointer and has to be printed
using the special %pap format string, as pointed out by
this new warning.
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h: In function ‘trace_raw_output_fjes_hw_start_debug_req’:
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h:212:563: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Note that this has to pass the address by reference instead of
casting it to a different type.
Fixes: b6ba737d0b29 ("fjes: ethtool -w and -W support for fjes driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Oct 2016 15:18:09 +0000 (11:18 -0400)]
Merge branch 'mv88e6xxx-interrupt-support'
Andrew Lunn says:
====================
Interrupt support for mv88e6xxx
This patchset add interrupt controller support to the MV88E6xxx. This
allows access to the interrupts the internal PHY generate. These
interrupts can then be associated to a PHY device in the device tree
and used by the PHY lib, rather than polling.
Since interrupt handling needs to make MDIO bus accesses, threaded
interrupts are used. The phylib needs to request the PHY interrupt
using the threaded IRQ API. This in term allows some simplification to
the code, in that the phylib interrupt handler can directly call
phy_change(), rather than use a work queue. The work queue is however
retained for the phy_mac_interrupt() call, which can be called in hard
interrupt context.
Since RFC v1:
Keep phy_mac_interrupt() callable in hard IRQ context.
The fix to trigger the phy state machine transitions on interrupts has
already been submitted, so is dropped from here.
Added back shared interrupts support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:53 +0000 (19:56 +0200)]
arm: vf610: zii devel b: Add support for switch interrupts
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:52 +0000 (19:56 +0200)]
net: phy: Use phy name when requesting the interrupt
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:51 +0000 (19:56 +0200)]
net: phy: Threaded interrupts allow some simplification
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:50 +0000 (19:56 +0200)]
net: phy: Use threaded IRQ, to allow IRQ from sleeping devices
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:49 +0000 (19:56 +0200)]
net: dsa: mv88e6xxx: Implement interrupt support.
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 15 Oct 2016 18:53:22 +0000 (11:53 -0700)]
rds: Remove duplicate prefix from rds_conn_path_error use
rds_conn_path_error already prefixes "RDS:" to the output.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 15 Oct 2016 18:53:21 +0000 (11:53 -0700)]
rds: Remove unused rds_conn_error
This macro's last use was removed in commit d769ef81d5b59
("RDS: Update rds_conn_shutdown to work with rds_conn_path")
so make the macro and the __rds_conn_error function definition
and declaration disappear.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Mon, 17 Oct 2016 04:25:35 +0000 (21:25 -0700)]
ila: Don't use dest cache when gateway is set
If the gateway is set on an ILA route we don't need to bother with using
the destination cache in the ILA route. Translation does not change the
routing in this case so we can stick with orig_output in the lwstate
output function.
Tested: Ran netperf with and without gateway for LWT route.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sat, 15 Oct 2016 15:40:30 +0000 (17:40 +0200)]
ipvlan: constify l3mdev_ops structure
This l3mdev_ops structure is only stored in the l3mdev_ops field of a
net_device structure. This field is declared const, so the l3mdev_ops
structure can be declared as const also. Additionally drop the
__read_mostly annotation.
The semantic patch that adds const is as follows:
(http://coccinelle.lip6.fr/)
David S. Miller [Sat, 15 Oct 2016 21:33:42 +0000 (17:33 -0400)]
Merge branch 'ila-cached-route'
Tom Herbert says:
====================
ila: Cache a route in ILA lwt structure
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do somthing like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Also, add destroy_state to lwt ops. We need this do destroy the
dst_cache.
- v2
- Fixed comparisons to fc_dst_len to make comparison against number
of bits in data structure not bytes.
- Move destroy_state under build_state (requested by Jiri)
- Other minor cleanup
Tested:
Running 200 TCP_RR streams:
Baseline, no ILA
1730716 tps
102/170/313 50/90/99% latencies
88.11 CPU utilization
Using ILA in both directions
1680428 tps
105/176/325 50/90/99% latencies
88.16 CPU utilization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 14 Oct 2016 18:25:37 +0000 (11:25 -0700)]
ila: Cache a route to translated address
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do something like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 14 Oct 2016 18:25:36 +0000 (11:25 -0700)]
lwtunnel: Add destroy state operation
Users of lwt tunnels may set up some secondary state in build_state
function. Add a corresponding destroy_state function to allow users to
clean up state. This destroy state function is called from lwstate_free.
Also, we now free lwstate using kfree_rcu so user can assume structure
is not freed before rcu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Oct 2016 16:04:58 +0000 (12:04 -0400)]
Merge branch 'fjes-next'
Taku Izumi says:
====================
FUJITSU Extended Socket driver version 1.2
This patchset updates FUJITSU Extended Socket network driver into version 1.2.
This includes the following enhancements:
- ethtool -d support
- ethtool -S enhancement
- ethtool -w/-W support
- Add some debugging feature (tracepoints etc)
v1 -> v2:
- Use u64 instead of phys_addr_t as TP_STRUCT__entry
- Use ethtool facility to achieve debug mode instead of using debugfs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log