mmc: sdhci-pci: disable preset register for Baytrail and Merrifield
Due to HW issue, SDHCI host controller on Intel
Baytrail/Merrifield platforms can not use preset
register. So, disable preset registers for them by quirks.
mmc: Add .multi_io_quirk callback for multi I/O HW bug
Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.
There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.
In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Chuanxiao.Dong [Tue, 19 Aug 2014 03:02:41 +0000 (11:02 +0800)]
mmc: sdhci: check 1.2v IO capability for SDHC host
Right now enable 1.2v IO voltage for SDHC is by using vqmmc.
Thus for the host which doesn't have vqmmc, or its vqmmc does
not support 1.2v, directly use MMC_CAP2_HS200 may cause HS200
failure.
So needs to check if vqmmc is able to support 1.2v. If it does
not support, disable 1.2v IO for HS200.
Chuanxiao.Dong [Fri, 15 Aug 2014 03:28:07 +0000 (11:28 +0800)]
mmc: core: Fix sequence for I/O voltage in DDR mode for eMMC
Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.
So the sequence will be:
if (host and device can both support 1.2v IO)
use 1.2v IO;
else if (host and device can both support 1.8v IO)
use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Robert Jarzmik [Tue, 2 Sep 2014 09:23:55 +0000 (11:23 +0200)]
mmc: pxamci: prepare and unprepare the clocks
Add the clock prepare and unprepare call to the driver set_ios calls
phase. This will remove a warning once the PXA architecture is migrated
to the clock infrastructure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Chanho Min [Sat, 30 Aug 2014 03:40:40 +0000 (12:40 +0900)]
mmc: sdhci: handle busy-end interrupt during command
It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Aisheng Dong [Wed, 27 Aug 2014 07:26:32 +0000 (15:26 +0800)]
mmc: sdhci: move timeout_clk dynamically calculation code into common code
The timeout_clk calculation code for SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK case
is common and could be moved into common sdhci_do_set_ios, then platform code
which is not using sdhci_set_clock does not need to write the same code again.
Aisheng Dong [Wed, 27 Aug 2014 07:26:31 +0000 (15:26 +0800)]
mmc: sdhci: calculate timeout_clk conditionally in sdhci_add_host
The timeout_clk calculation code in sdhci_add_host is meaningless for
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
So only execute them with no SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK set.
Aisheng Dong [Wed, 27 Aug 2014 07:26:30 +0000 (15:26 +0800)]
mmc: sdhci-esdhc-imx: set the correct max timeout value for uSDHC
The default sdhci driver write 0xE into timeout counter register to
set the maximum timeout. The value is not correct for uSDHC since the
max counter value for uSDHC is 0xF.
Instead of using common timeout code in sdhci, we implement esdhc_set_timeout
to handle the difference between eSDHC and uSDHC.
Currently we simply set the max timeout value as before.
But in the future, we probably may implement IMX specific timeout
setting algorithm and use suitable timeout for different CMDs.
Aisheng Dong [Wed, 27 Aug 2014 07:26:29 +0000 (15:26 +0800)]
mmc: sdhci: add platform set_timeout hook
Currently the common code assume 0xE is the maximum timeout counter
value and use it to write into the timeout counter register.
However, it's fairly possible that some other SoCs may have different
max timeout register value. That means 0xE may be incorrect and
becomes meaningless.
It's also possible that other platforms has different timeout
calculation algorithm. To be flexible, this patch provides a .set_timeout
hook for those platforms to set the timeout on their way if they need.
Aisheng Dong [Wed, 27 Aug 2014 07:26:28 +0000 (15:26 +0800)]
mmc: sdhci-esdhc-imx: fix incorrect max timeout cout for uSDHC
The default sdhci code use the 1 << 27 as the max timeout counter to
to calculate the max_busy_timeout, however it's not correct for uSDHC
since its the max counter is 1 << 28.
Implement esdhc_get_max_timeout_cout to handle it correctly.
Currently the max timeout count is hardcode to 1 << 27 for calcuate
the max_busy_timeout, however, for some platforms the max timeout
count may not be 1 << 27, e.g. i.MX uSDHC is 1 << 28.
Thus 1 << 27 is not correct for such platform.
It is also possible that other platforms may have different values.
To be flexible, we add a get_max_timeout_count hook to get the correct
maximum timeout value for these platforms.
Doug Anderson [Mon, 25 Aug 2014 18:19:04 +0000 (11:19 -0700)]
mmc: dw_mmc: Pass back errors from mmc_of_parse()
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Minda Chen [Tue, 26 Aug 2014 02:50:42 +0000 (10:50 +0800)]
mmc: sdhci-sirf: fix 8bit width enable by overwriting set_bus_width
the implementation of CSR SDHCI controller is a modified version of
the one described in the 1.0 specification, and not a normal 3.0
controller.
and 8bit-width enable bit of CSR MMC hosts is 3, while stardard hosts
use bit 5.
this patch fixes the functionality of 8bit transfer in mmc controllers
and improve performance for mmc0 a lot.
Signed-off-by: Minda Chen <Minda.Chen@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Reviewed-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doug Anderson [Fri, 22 Aug 2014 13:47:51 +0000 (19:17 +0530)]
mmc: dw_mmc: Support voltage changes
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yuvaraj CD [Fri, 22 Aug 2014 13:47:50 +0000 (19:17 +0530)]
mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So, seems this bad SD card does not set valid value in related SSR / CSD register fields.
And then the driver will set card->erase_size to 0.
Then it triggered this divided by zero error when calculate card->pref_erase.
Shinobu Uehara [Mon, 25 Aug 2014 03:03:00 +0000 (20:03 -0700)]
mmc: tmio: add actual clock support as option
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
mmc: tmio: remove SCLKEN bit setting from tmio_mmc_set_clock()
TMIO clock is set via tmio_mmc_set_clock() -> tmio_mmc_clk_start(),
and SCLKEN bit will be set on tmio_mmc_clk_start().
It is not needed on tmio_mmc_set_clock() function.
The required clock setting will not be able to set
in some clocks without this patch.
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp> Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shinobu Uehara [Mon, 25 Aug 2014 03:01:32 +0000 (20:01 -0700)]
mmc: tmio: check ILL_FUNC instead of CBSY
Some controllers need to check SD bus status when writing data.
Then, it checks ILL_FUNC bit on SD_INFO2 register,
and this method is controlled via TMIO_MMC_HAS_IDLE_WAIT flags.
Same method is required on tmio_mmc_data_irq() which will
be called after writing data.
Current driver is checking CBSY bit for this purpose,
but, some controllers doesn't have CBSY bit.
This patch checks ILL_FUNC bit instead of CBSY bit
if it has TMIO_MMC_HAS_IDLE_WAIT flags
Shinobu Uehara [Mon, 25 Aug 2014 03:00:52 +0000 (20:00 -0700)]
mmc: tmio: add TMIO_MMC_SDIO_STATUS_QUIRK
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)
This patch adds new .dma_rx_offset and cares it
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp> Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp> Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 25 Aug 2014 10:28:20 +0000 (12:28 +0200)]
mmc: tmio_mmc: Fixup system PM suspend lock-up
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Ulf Hansson [Mon, 25 Aug 2014 10:18:26 +0000 (12:18 +0200)]
mmc: sdhi: Fixup system PM suspend lock-up
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.
The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.
In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.
Ulf Hansson [Thu, 24 Oct 2013 15:53:15 +0000 (17:53 +0200)]
mmc: tmio: Restructure ->set_ios() and adapt ->probe() to it
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.
By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.
Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
mmc: core: Use regulator_get_voltage() if OCR mask is empty.
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
Sascha Hauer [Tue, 19 Aug 2014 08:45:51 +0000 (10:45 +0200)]
mmc: implement Driver Stage Register handling
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Peter Griffin [Fri, 15 Aug 2014 13:02:15 +0000 (14:02 +0100)]
mmc: sdhci-pxav3: set_uhs_signaling is initialized twice differently
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.
This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.
This happened in
commit 96d7b78cfc2f ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2a9 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'
Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.
Peter Griffin [Tue, 12 Aug 2014 16:14:27 +0000 (17:14 +0100)]
mmc: dw_mmc-pltfm: Remove superflous #else condition on CONFIG_PM_SLEEP
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peter Griffin [Tue, 12 Aug 2014 16:14:26 +0000 (17:14 +0100)]
mmc: dw_mmc-pci: Remove superflous #else condition on CONFIG_PM_SLEEP
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peter Griffin [Tue, 12 Aug 2014 16:14:25 +0000 (17:14 +0100)]
mmc: remove .owner field for drivers using module_platform_driver
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fu Zhonghui [Mon, 18 Aug 2014 02:48:14 +0000 (10:48 +0800)]
mmc: core: sdio: Fix unconditional wake_up_process() on sdio thread
781e989cf59 ("mmc: sdhci: convert to new SDIO IRQ handling") and bf3b5ec66bd ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time. Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <chris@printf.net> Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com> Cc: <stable@vger.kernel.org> # v3.16+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA. Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Matthieu CASTET [Thu, 14 Aug 2014 14:03:18 +0000 (16:03 +0200)]
sdhci : recompute timeout_clk when needed
when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).
Matthieu CASTET [Thu, 14 Aug 2014 14:03:17 +0000 (16:03 +0200)]
sdhci : handle busy timeout irq
When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.
Roger Tseng [Fri, 15 Aug 2014 06:06:01 +0000 (14:06 +0800)]
mmc: rtsx_usb_sdmmc: fix incorrect last byte in R2 response
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Roger Tseng [Fri, 15 Aug 2014 06:06:00 +0000 (14:06 +0800)]
mmc: rtsx_pci_sdmmc: fix incorrect last byte in R2 response
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Doug Anderson [Wed, 13 Aug 2014 15:13:43 +0000 (08:13 -0700)]
mmc: dw_mmc: Make sure we don't get stuck when we get an error
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com> Acked-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yi Sun [Wed, 13 Aug 2014 05:34:01 +0000 (13:34 +0800)]
mmc: Correct the value of MMC_NUM_PHY_PARTITION
eMMC card can support up to 7 physical partitions, including 2 boot,
1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is
the correct value.
Signed-off-by: Yi Sun <yi.y.sun@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Chuanxiao.Dong [Fri, 1 Aug 2014 06:00:13 +0000 (14:00 +0800)]
mmc: sdhci: fix the wrong type of curr
curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32
mmc: jz4740: prepare next dma transfer in parallel with current transfer
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.
It should help reduce the impact of DMA preparation overhead on the SD
card performance.
mmc: jz4740: add dma infrastructure for data transfers
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.
DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Pawel Moll [Tue, 12 Aug 2014 10:37:52 +0000 (11:37 +0100)]
mmc: sdhci-pltfm: Do not use parent as the host's device
The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb13843f5082e82970dd1e8031383134a65
"mmc: sdhci-pltfm: Add structure for host-specific data" and a4d2177f00a5252d825236c5124bc1e9918bdb41 "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.
The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.
Tim Kryger [Tue, 12 Aug 2014 05:05:12 +0000 (22:05 -0700)]
mmc: core: Remove fixed voltage regulator logic
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.
Most of this code has been ported from qualcomm's 3.4 kernel.
This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
mmc: sdhci-s3c: fix runtime PM handling on sdhci_add_host() failure
Runtime Power Management handling for the sdhci_add_host() failure
case in sdhci_s3c_probe() should match the code in sdhci_s3c_remove()
(which uses pm_runtime_disable() call which matches the earlier
pm_runtime_enable() one). Fix it.
This patch fixes "BUG: spinlock bad magic on CPU#0, swapper/0/1" and
"Unbalanced pm_runtime_enable!" warnings.
>From the kernel log:
...
[ 1.659631] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[ 1.665096] BUG: spinlock bad magic on CPU#0, swapper/0/1
[ 1.670433] lock: 0xea01e484, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 1.677895] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty #707
[ 1.687037] [<c0013ae4>] (unwind_backtrace) from [<c0010d70>] (show_stack+0x10/0x14)
[ 1.694740] [<c0010d70>] (show_stack) from [<c04050c8>] (dump_stack+0x68/0xb8)
[ 1.701948] [<c04050c8>] (dump_stack) from [<c0052558>] (do_raw_spin_lock+0x15c/0x1a4)
[ 1.709848] [<c0052558>] (do_raw_spin_lock) from [<c040a630>] (_raw_spin_lock_irqsave+0x20/0x28)
[ 1.718619] [<c040a630>] (_raw_spin_lock_irqsave) from [<c030d7d0>] (sdhci_do_set_ios+0x1c/0x5cc)
[ 1.727464] [<c030d7d0>] (sdhci_do_set_ios) from [<c030ddfc>] (sdhci_runtime_resume_host+0x50/0x104)
[ 1.736574] [<c030ddfc>] (sdhci_runtime_resume_host) from [<c02462dc>] (pm_generic_runtime_resume+0x2c/0x40)
[ 1.746383] [<c02462dc>] (pm_generic_runtime_resume) from [<c0247898>] (__rpm_callback+0x34/0x70)
[ 1.755233] [<c0247898>] (__rpm_callback) from [<c02478fc>] (rpm_callback+0x28/0x88)
[ 1.762958] [<c02478fc>] (rpm_callback) from [<c02486f0>] (rpm_resume+0x384/0x4ec)
[ 1.770511] [<c02486f0>] (rpm_resume) from [<c02488b0>] (pm_runtime_forbid+0x58/0x64)
[ 1.778325] [<c02488b0>] (pm_runtime_forbid) from [<c030ea70>] (sdhci_s3c_probe+0x4a4/0x540)
[ 1.786749] [<c030ea70>] (sdhci_s3c_probe) from [<c02429cc>] (platform_drv_probe+0x2c/0x5c)
[ 1.795076] [<c02429cc>] (platform_drv_probe) from [<c02415f0>] (driver_probe_device+0x114/0x234)
[ 1.803929] [<c02415f0>] (driver_probe_device) from [<c024179c>] (__driver_attach+0x8c/0x90)
[ 1.812347] [<c024179c>] (__driver_attach) from [<c023ffb4>] (bus_for_each_dev+0x54/0x88)
[ 1.820506] [<c023ffb4>] (bus_for_each_dev) from [<c0240df8>] (bus_add_driver+0xd8/0x1cc)
[ 1.828665] [<c0240df8>] (bus_add_driver) from [<c0241db8>] (driver_register+0x78/0xf4)
[ 1.836652] [<c0241db8>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1d0)
[ 1.844816] [<c00088a4>] (do_one_initcall) from [<c059ac94>] (kernel_init_freeable+0x108/0x1d4)
[ 1.853503] [<c059ac94>] (kernel_init_freeable) from [<c0401300>] (kernel_init+0x8/0xe4)
[ 1.861568] [<c0401300>] (kernel_init) from [<c000e538>] (ret_from_fork+0x14/0x3c)
[ 1.869582] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
[ 1.997047] s3c-sdhci 12530000.sdhci: Unbalanced pm_runtime_enable!
...
[ 2.027235] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[ 2.032884] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
Tested on Hardkernel's Exynos4412 based ODROID-U3 board.
Fixes: 9f4e8151dbbc ("mmc: sdhci-s3c: Enable runtime power management") Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Paul Bolle [Sun, 7 Sep 2014 18:25:55 +0000 (11:25 -0700)]
Documentation: NFS/RDMA: Document separate Kconfig symbols
The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit 2e8c12e1b765 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").
Update the documentation to reflect this split.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: "J. Bruce Fields" <bfields@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.
By documenting them, hopefully they will become more widely used.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk> Acked-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull filesystem fixes from Al Viro:
"Several bugfixes (all of them -stable fodder).
Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
has tried to test "ufs: sb mutex merge + mutex_destroy" on something
like file creation/removal on ufs). Mine deal with two kinds of
umount bugs, in umount propagation and in handling of automounted
submounts, both resulting in bogus transient EBUSY from umount"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix deadlocks introduced by sb mutex merge
fix EBUSY on umount() from MNT_SHRINKABLE
get rid of propagate_umount() mistakenly treating slaves as busy.
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
&& (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make nocb leader kthreads process pending callbacks after spawning
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets from the timer departement:
- Update the timekeeper before updating vsyscall and pvclock. This
fixes the kvm-clock regression reported by Chris and Paolo.
- Use the proper irq work interface from NMI. This fixes the
regression reported by Catalin and Dave.
- Clarify the compat_nanosleep error handling mechanism to avoid
future confusion"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Update timekeeper before updating vsyscall and pvclock
compat: nanosleep: Clarify error handling
nohz: Restore NMI safe local irq work for local nohz kick
Commit 0244756edc4b ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.
The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.
Found by Linux Driver Verification project (linuxtesting.org).
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
Merge tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"The fixes all address recently discovered data corruption issues.
The original Direct IO issue was discovered by Chris Mason @ Facebook
on a production workload which mixed buffered reads with direct reads
and writes IO to the same file. The fix for that exposed other issues
with page invalidation (exposed by millions of fsx operations) failing
due to dirty buffers beyond EOF.
Finally, the collapse_range code could also cause problems due to
racing writeback changing the extent map while it was being shifted
around. The commits for that problem are simple mitigation fixes that
prevent the problem from occuring. A more robust fix for 3.18 that
addresses the underlying problem is currently being worked on by
Brian.
Summary of fixes:
- a direct IO read/buffered read data corruption
- the associated fallout from the DIO data corruption fix
- collapse range bugs that are potential data corruption issues"
* tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: trim eofblocks before collapse range
xfs: xfs_file_collapse_range is delalloc challenged
xfs: don't log inode unless extent shift makes extent modifications
xfs: use ranged writeback and invalidation for direct IO
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't dirty buffers beyond EOF
Merge tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
Thomas Gleixner [Sat, 6 Sep 2014 10:24:49 +0000 (12:24 +0200)]
timekeeping: Update timekeeper before updating vsyscall and pvclock
The update_walltime() code works on the shadow timekeeper to make the
seqcount protected region as short as possible. But that update to the
shadow timekeeper does not update all timekeeper fields because it's
sufficient to do that once before it becomes life. One of these fields
is tkr.base_mono. That stays stale in the shadow timekeeper unless an
operation happens which copies the real timekeeper to the shadow.
The update function is called after the update calls to vsyscall and
pvclock. While not correct, it did not cause any problems because none
of the invoked update functions used base_mono.
commit cbcf2dd3b3d4 (x86: kvm: Make kvm_get_time_and_clockread()
nanoseconds based) changed that in the kvm pvclock update function, so
the stale mono_base value got used and caused kvm-clock to malfunction.
Put the update where it belongs and fix the issue.
Reported-by: Chris J Arges <chris.j.arges@canonical.com> Reported-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: John Stultz <john.stultz@linaro.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409050000570.3333@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sat, 6 Sep 2014 10:18:07 +0000 (12:18 +0200)]
compat: nanosleep: Clarify error handling
The error handling in compat_sys_nanosleep() is correct, but
completely non obvious. Document it and restrict it to the
-ERESTART_RESTARTBLOCK return value for clarity.
Reported-by: Kees Cook <keescook@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"I2C driver bugfixes for the 3.17 release. Details can be found in the
commit messages, yet I think this is typical driver stuff"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: rcar: remove spinlock"
i2c: at91: add bound checking on SMBus block length bytes
i2c: rk3x: fix bug that cause transfer fails in master receive mode
i2c: at91: Fix a race condition during signal handling in at91_do_twi_xfer.
i2c: mv64xxx: continue probe when clock-frequency is missing
i2c: rcar: fix MNR interrupt handling
The function cleaning up an initialized event
was called from the "event_del" handler, instead
of being used as the "destroy" callback. In case of
events group allocation this caused NULL pointer
dereference (as events are added and deleted
multiple times then). Fixed now.
Signed-off-by: Pawel Moll <mail@pawelmoll.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
Actually register clocks from device tree when using the common clock
framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: add at91 to function name] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Johannes Weiner [Fri, 5 Sep 2014 12:43:57 +0000 (08:43 -0400)]
mm: memcontrol: revert use of root_mem_cgroup res_counter
Dave Hansen reports a massive scalability regression in an uncontained
page fault benchmark with more than 30 concurrent threads, which he
bisected down to 05b843012335 ("mm: memcontrol: use root_mem_cgroup
res_counter") and pin-pointed on res_counter spinlock contention.
That change relied on the per-cpu charge caches to mostly swallow the
res_counter costs, but it's apparent that the caches don't scale yet.
Revert memcg back to bypassing res_counters on the root level in order
to restore performance for uncontained workloads.
Reported-by: Dave Hansen <dave@sr71.net> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Tested-by: Dave Hansen <dave.hansen@intel.com> Acked-by: Michal Hocko <mhocko@suse.cz> Acked-by: Vladimir Davydov <vdavydov@parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log