Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels] Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
spin_is_locked() always returns false for uniprocessor configurations
in several architectures, so do not use WARN_ON with it.
Use lockdep_assert_held() instead to also reduce overhead in
non-debug kernels.
v2 (Andreas Boll):
- Drop usage of packet3 for new firmware
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> (v1) Signed-off-by: Andreas Boll <andreas.boll.dev@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4badad352a6bb202ec68afa7a574c0bb961e5ebc (locking/mutex: Disable
optimistic spinning on some architectures) fenced spinning for
architectures without proper cmpxchg.
There is no need to disable mutex spinning on s390, though:
The instructions CS,CSG and friends provide the proper guarantees.
(We dont implement cmpxchg with locks).
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit id 2bd16e3e23d9df41592c6b257c59b6860a9cc3ea
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.
Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).
Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed) Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit f814f9ac5a81 ("spi/orion: add device tree binding"), Device
Tree support was added to the spi-orion driver. However, this commit
reads the "cell-index" property, without taking into account the fact
that DT properties are big-endian encoded.
Since most of the platforms using spi-orion with DT have apparently
not used anything but cell-index = <0>, the problem was not
visible. But as soon as one starts using cell-index = <1>, the problem
becomes clearly visible, as the master->bus_num gets a wrong value
(actually it gets the value 0, which conflicts with the first bus that
has cell-index = <0>).
This commit fixes that by using of_property_read_u32() to read the
property value, which does the appropriate endianness conversion when
needed.
Fixes: f814f9ac5a81 ("spi/orion: add device tree binding") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple devices are detached in __detach_device, they
are also removed from the domains dev_list. This makes it
unsafe to use list_for_each_entry_safe, as the next pointer
might also not be in the list anymore after __detach_device
returns. So just repeatedly remove the first element of the
list until it is empty.
X-Patchwork-Delegate: mchehab@redhat.com
Remove the CONFIG_ prefix from two Kconfig symbols in a dependency for
SMS_SIANO_DEBUGFS. This prefix is invalid inside Kconfig files.
Note that the current (common sense) dependency on SMS_USB_DRV and
SMS_SDIO_DRV being equal ensures that SMS_SIANO_DEBUGFS will not
violate its constraints. These constraint are that:
- it should only be built if SMS_USB_DRV is set;
- it can't be builtin if USB support is modular.
So drop the dependency on SMS_USB_DRV, as it is unneeded.
Fixes: 6c84b214284e ("[media] sms: fix randconfig building error") Reported-by: Martin Walch <walch.martin@web.de> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a bug caused by the struct vb2_buffer field not being be the
very first field of the vsp1_video_buffer buffer structure as required
by videobuf2.
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.
I found two different encarnations of this issue:
1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.
The fix is simple: just check if alt=5 before calling
set_usb_interface().
The programmed frequency on xc4000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
This works fine on set_frontend, as the device calculates
the needed offset. However, at get_frequency(), the returned
value is the initial frequency. That's generally not a big
problem on most drivers, however, starting with changeset 6fe1099c7aec, the frequency drift is taken into account at
dib7000p driver.
This broke support for PCTV 340e, with uses dib7000p demod and
xc4000 tuner.
The programmed frequency on xc5000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
commit bdd405d2a528 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Roger Quadros <rogerq@ti.com> Cc: Michael Welling <mwelling@emacinc.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the presence of delegations, we can no longer assume that the
state->n_rdwr, state->n_rdonly, state->n_wronly reflect the open
stateid share mode, and so we need to calculate the initial value
for calldata->arg.fmode using the state->flags.
Reported-by: James Drews <drews@engr.wisc.edu> Fixes: 88069f77e1ac5 (NFSv41: Fix a potential state leakage when...) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a new object on the NFS server, we should not be sending
posix setacl requests unless the preceding posix_acl_create returned a
non-trivial acl. Doing so, causes Solaris servers in particular to
return an EINVAL.
The current code always selects XPRT_TRANSPORT_BC_TCP for the back
channel, even when the forward channel was not TCP (eg, RDMA). When
a 4.1 mount is attempted with RDMA, the server panics in the TCP BC
code when trying to send CB_NULL.
Instead, construct the transport protocol number from the forward
channel transport or'd with XPRT_TRANSPORT_BC. Transports that do
not support bi-directional RPC will not have registered a "BC"
transport, causing create_backchannel_client() to fail immediately.
Fixes: https://bugzilla.linux-nfs.org/show_bug.cgi?id=265 Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a check for result being not NULL. But get_acl() may return
NULL, or ERR_PTR, or actual pointer.
The purpose of the function where current change is done is to "list
ACLs only when they are available", so any error condition of get_acl()
mustn't be elevated, and returning 0 there is still valid.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81111 Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 74adf83f5d77 (nfs: only show Posix ACLs in listxattr if actually...) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A memory allocation failure could cause nfsd_startup_generic to fail, in
which case nfsd_users wouldn't be incorrectly left elevated.
After nfsd restarts nfsd_startup_generic will then succeed without doing
anything--the first consequence is likely nfs4_start_net finding a bad
laundry_wq and crashing.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Fixes: 4539f14981ce "nfsd: replace boolean nfsd_up flag by users counter" Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a211d introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a211d "USB: set hub's default autosuspend delay as 0" Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Michael Welling <mwelling@emacinc.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.
This patch is for v3.12+.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a potential security issue in the whiteheat USB driver
which might allow a local attacker to cause kernel memory corrpution. This
is due to an unchecked memcpy into a fixed size buffer (of 64 bytes). On
EHCI and XHCI busses it's possible to craft responses greater than 64
bytes leading a buffer overflow.
Signed-off-by: James Forshaw <forshaw@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device id for Basic Micro ATOM Nano USB2Serial adapters.
Reported-by: Nicolas Alt <n.alt@mytum.de> Tested-by: Nicolas Alt <n.alt@mytum.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.
My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.
In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.
So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.
Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two reported bugs, caused by et131x_adapter->phydev->addr being accessed
before it is initialised, by:
- letting et131x_mii_write() take a phydev address, instead of using the one
stored in adapter by default. This is so et131x_mdio_write() can use it's own
addr value.
- removing implementation of et131x_mdio_reset(), as it's not needed.
- moving a call to et131x_disable_phy_coma() in et131x_pci_setup(), which uses
phydev->addr, until after the mdiobus has been registered.
It turns out that there are some serious problems with the on-disk
format of journal checksum v2. The foremost is that the function to
calculate descriptor tag size returns sizes that are too big. This
causes alignment issues on some architectures and is compounded by the
fact that some parts of jbd2 use the structure size (incorrectly) to
determine the presence of a 64bit journal instead of checking the
feature flags.
Therefore, introduce journal checksum v3, which enlarges the
descriptor block tag format to allow for full 32-bit checksums of
journal blocks, fix the journal tag function to return the correct
sizes, and fix the jbd2 recovery code to use feature flags to
determine 64bitness.
Add a few function helpers so we don't have to open-code quite so
many pieces.
Switching to a 16-byte block size was found to increase journal size
overhead by a maximum of 0.1%, to convert a 32-bit journal with no
checksumming to a 32-bit journal with checksum v3 enabled.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reported-by: TR Reardon <thomas_reardon@hotmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When recovering the journal, don't fall into an infinite loop if we
encounter a corrupt journal block. Instead, just skip the block and
return an error, which fails the mount and thus forces the user to run
a full filesystem fsck.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of delalloc block i_disksize may be less than i_size. So we
have to update i_disksize each time we allocated and submitted some
blocks beyond i_disksize. We weren't doing this on the error paths,
so fix this.
If connect request is queued (e.g. device in pg) set client state
to initializing, thus avoid preliminary exit in wait if current
state is disconnected.
This is regression from:
commit e4d8270e604c3202131bac607969605ac397b893
Author: Alexander Usyskin <alexander.usyskin@intel.com>
mei: set connecting state just upon connection request is sent to the fw
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
------------[ cut here ]------------
kernel BUG at fs/btrfs/extent_io.c:2124!
[...]
Workqueue: btrfs-endio normal_work_helper [btrfs]
RIP: 0010:[<ffffffffa02d6055>] [<ffffffffa02d6055>] end_bio_extent_readpage+0xb45/0xcd0 [btrfs]
This is in fact a regression.
It is because we forgot to increase @offset properly in reading corrupted block,
so that the @offset remains, and this leads to checksum errors while reading
left blocks queued up in the same bio, and then ends up with hiting the above
BUG_ON.
Reported-by: Chris Murphy <lists@colorremedies.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing to allocate space for the whole compressed extent, we'll
fallback to uncompressed IO, but we've forgotten to redirty the pages
which belong to this compressed extent, and these 'clean' pages will
simply skip 'submit' part and go to endio directly, at last we got data
corruption as we write nothing.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Tested-By: Martin Steigerwald <martin@lichtvoll.de> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under rare circumstances we can end up leaving 2 versions of a checksum
for the same file extent range.
The reason for this is that after calling btrfs_next_leaf we process
slot 0 of the leaf it returns, instead of processing the slot set in
path->slots[0]. Most of the time (by far) path->slots[0] is 0, but after
btrfs_next_leaf() releases the path and before it searches for the next
leaf, another task might cause a split of the next leaf, which migrates
some of its keys to the leaf we were processing before calling
btrfs_next_leaf(). In this case btrfs_next_leaf() returns again the
same leaf but with path->slots[0] having a slot number corresponding
to the first new key it got, that is, a slot number that didn't exist
before calling btrfs_next_leaf(), as the leaf now has more keys than
it had before. So we must really process the returned leaf starting at
path->slots[0] always, as it isn't always 0, and the key at slot 0 can
have an offset much lower than our search offset/bytenr.
For example, consider the following scenario, where we have:
Because we are at the last slot of leaf N, we call btrfs_next_leaf() to
find the next highest key, which releases the current path and then searches
for that next key. However after releasing the path and before finding that
next key, the item at slot 0 of leaf N + 1 gets moved to leaf N, due to a call
to ctree.c:push_leaf_left() (via ctree.c:split_leaf()), and therefore
btrfs_next_leaf() will returns us a path again with leaf N but with the slot
pointing to its new last key (CSUM CSUM 40161280). This new version of leaf N
is then:
In other words, we insert a new csum item in the tree with key
(CSUM_OBJECTID CSUM_KEY 40157184 = sums->bytenr) that contains the checksums
for all the data (4 blocks of 4096 bytes each = sums->len). Which is wrong,
because the item with key (CSUM CSUM 40161280) (the one that was moved from
leaf N + 1 to the end of leaf N) contains the old checksums of the last 12288
bytes of our data and won't get those old checksums removed.
So this leaves us 2 different checksums for 3 4kb blocks of data in the tree,
and breaks the logical rule:
An obvious bad effect of this is that a subsequent csum tree lookup to get
the checksum of any of the blocks with logical offset of 40161280, 40165376
or 40169472 (the last 3 4kb blocks of file data), will get the old checksums.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This indicates a NULL corruption in prefs_delayed list. The further
investigation and bisection pointed that the call of ulist_add_merge()
results in the corruption.
ulist_add_merge() takes u64 as aux and writes a 64bit value into
old_aux. The callers of this function in backref.c, however, pass a
pointer of a pointer to old_aux. That is, the function overwrites
64bit value on 32bit pointer. This caused a NULL in the adjacent
variable, in this case, prefs_delayed.
Here is a quick attempt to band-aid over this: a new function,
ulist_add_merge_ptr() is introduced to pass/store properly a pointer
value instead of u64. There are still ugly void ** cast remaining
in the callers because void ** cannot be taken implicitly. But, it's
safer than explicit cast to u64, anyway.
When copy_from_user fails, return -EFAULT, not -ENOMEM
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Reported-by: Robert Elliott <elliott@hp.com> Reviewed-by: Joe Handzik <joseph.t.handzik@hp.com> Reviewed-by: Scott Teel <scott.teel@hp.com>
Reviewed by: Mike MIller <michael.miller@canonical.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the timer irqs are resumed during device resume it is possible in
certain circumstances for the resume to hang early on, before device
interrupts are resumed. For an Ubuntu 14.04 PVHVM guest this would
occur in ~0.5% of resume attempts.
It is not entirely clear what is occuring the point of the hang but I
think a task necessary for the resume calls schedule_timeout(),
waiting for a timer interrupt (which never arrives). This failure may
require specific tasks to be running on the other VCPUs to trigger
(processes are not frozen during a suspend/resume if PREEMPT is
disabled).
Add IRQF_EARLY_RESUME to the timer interrupts so they are resumed in
syscore_resume().
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b7dd0e350e0b (x86/xen: safely map and unmap grant frames when
in atomic context) causes PVH guests to crash in
arch_gnttab_map_shared() when they attempted to map the pages for the
grant table.
This use of a PV-specific function during the PVH grant table setup is
non-obvious and not needed. The standard vmap() function does the
right thing.
Without CONFIG_RELOCATABLE the early boot code will decompress the
kernel to LOAD_PHYSICAL_ADDR. While this may have been fine in the BIOS
days, that isn't going to fly with UEFI since parts of the firmware
code/data may be located at LOAD_PHYSICAL_ADDR.
Straying outside of the bounds of the regions we've explicitly requested
from the firmware will cause all sorts of trouble. Bruno reports that
his machine resets while trying to decompress the kernel image.
We already go to great pains to ensure the kernel is loaded into a
suitably aligned buffer, it's just that the address isn't necessarily
LOAD_PHYSICAL_ADDR, because we can't guarantee that address isn't in-use
by the firmware.
Explicitly enforce CONFIG_RELOCATABLE for the EFI boot stub, so that we
can load the kernel at any address with the correct alignment.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org> Tested-by: Bruno Prémont <bonbons@linux-vserver.org> Cc: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the FIFO-based ABI on x86_64, if the last port is at the
end of an event array page then sync_test_bit() on this port's event
word will read beyond the end of the page and in certain circumstances
this may fault.
The fault requires the following page in the kernel's direct mapping
to be not present, which would mean:
a) the array page is the last page of RAM; or
b) the following page is ballooned out /and/ it has been used for a
foreign mapping by a kernel driver (such as netback or blkback)
/and/ the grant has been unmapped.
Use the infrastructure added for arm64 to ensure that all bitops
operating on event words are unsigned long aligned.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28e134464734 "[SCSI] hpsa: enable unit attention reporting"
turns on unit attention notifications, but got the change wrong for
all architectures other than x86, which now store an uninitialized
value into the device register.
Gcc helpfully warns about this:
../drivers/scsi/hpsa.c: In function 'hpsa_set_driver_support_bits':
../drivers/scsi/hpsa.c:6373:17: warning: 'driver_support' is used uninitialized in this function [-Wuninitialized]
driver_support |= ENABLE_UNIT_ATTN;
^
This moves the #ifdef so only the prefetch-enable is conditional
on x86, not also reading the initial register contents.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 28e134464734 "[SCSI] hpsa: enable unit attention reporting" Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc defines various machine-specific routines for handling
pci_set_dma_mask(). The routines for machine "PowerNV" may neglect
to set dev->dma_mask. This could confuse anyone (e.g. drivers) that
consult dev->dma_mask to find the current mask. Set the dma_mask in
the PowerNV leaf routine.
Signed-off-by: Brian W. Hart <hartb@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bcdde7e made __sysfs_remove_dir() recursive and introduced a BUG_ON
during PHB removal while attempting to delete the power managment attribute
group of the bus. This is a result of tearing the bridge and bus devices down
out of order in remove_phb_dynamic. Since, the the bus resides below the bridge
in the sysfs device tree it should be torn down first.
This patch simply moves the device_unregister call for the PHB bridge device
after the device_unregister call for the PHB bus.
Fixes: bcdde7e221a8 ("sysfs: make __sysfs_remove_dir() recursive") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30919b0bf356 ("x86: avoid low BIOS area when allocating address
space") moved the test for resource allocations that fall within the first
1MB of address space from the PCI-specific path to a generic path, such
that all resource allocations will avoid this area. However, this breaks
ISA cards which need to allocate a memory region within the first 1MB. An
example is the i82365 PCMCIA controller and derivatives like the Ricoh
RF5C296/396 which map part of the PCMCIA socket memory address space into
the first 1MB of system memory address space. They do not work anymore as
no usable memory region exists due to this change:
Fix errors in handling "device label" _DSM return values.
If _DSM returns a Unicode string, the ACPI type is ACPI_TYPE_BUFFER, not
ACPI_TYPE_STRING. Fix dsm_label_utf16s_to_utf8s() to convert UTF-16 from
acpi_object->buffer instead of acpi_object->string.
Prior to v3.14, we accepted Unicode labels (ACPI_TYPE_BUFFER return
values). But after 1d0fcef73283, we accepted only ASCII (ACPI_TYPE_STRING)
(and we incorrectly tried to convert those ASCII labels from UTF-16 to
UTF-8).
Rejecting Unicode labels made us return -EPERM when reading sysfs
"acpi_index" or "label" files, which in turn caused on-board network
interfaces on a Dell PowerEdge E420 to be renamed (by udev net_id internal)
from eno1/eno2 to enp2s0f0/enp2s0f1.
Fix this by accepting either ACPI_TYPE_STRING (and treating it as ASCII) or
ACPI_TYPE_BUFFER (and converting from UTF-16 to UTF-8).
We can't do ASPM configuration at enumeration-time because enabling it
makes some defective hardware unresponsive, even if ASPM is disabled later
(see 41cd766b0659 ("PCI: Don't enable aspm before drivers have had a chance
to veto it"). Therefore, we have to do it after a driver claims the
device.
We previously configured ASPM in pci_set_power_state(), but that's not a
very good place because it's not really related to setting the PCI device
power state, and doing it there means:
- We incorrectly skipped ASPM config when setting a device that's
already in D0 to D0.
- We unnecessarily configured ASPM when setting a device to a low-power
state (the ASPM feature only applies when the device is in D0).
- We unnecessarily configured ASPM when called from a .resume() method
(ASPM configuration needs to be restored during resume, but
pci_restore_pcie_state() should already do this).
Move ASPM configuration from pci_set_power_state() to
do_pci_enable_device() so we do it when a driver enables a device.
If we suffer a block allocation failure (for example due to a memory
allocation failure), it's possible that we will call
ext4_discard_allocated_blocks() before we've actually allocated any
blocks. In that case, fe_len and fe_start in ac->ac_f_ex will still
be zero, and this will result in mb_free_blocks(inode, e4b, 0, 0)
triggering the BUG_ON on mb_free_blocks():
BUG_ON(last >= (sb->s_blocksize << 3));
Fix this by bailing out of ext4_discard_allocated_blocks() if fs_len
is zero.
Also fix a missing ext4_mb_unload_buddy() call in
ext4_discard_allocated_blocks().
The third parameter of kvm_iommu_put_pages is wrong,
It should be 'gfn - slot->base_gfn'.
By making gfn very large, malicious guest or userspace can cause kvm to
go to this error path, and subsequently to pass a huge value as size.
Alternatively if gfn is small, then pages would be pinned but never
unpinned, causing host memory leak and local DOS.
Passing a reasonable but large value could be the most dangerous case,
because it would unpin a page that should have stayed pinned, and thus
allow the device to DMA into arbitrary memory. However, this cannot
happen because of the condition that can trigger the error:
- out of memory (where you can't allocate even a single page)
should not be possible for the attacker to trigger
- when exceeding the iommu's address space, guest pages after gfn
will also exceed the iommu's address space, and inside
kvm_iommu_put_pages() the iommu_iova_to_phys() will fail. The
page thus would not be unpinned at all.
Reported-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SeaBIOS has a limit on the number of MTRRs that it can handle,
and this patch exceeded the limit. Better revert it.
Thanks to Nadav Amit for debugging the cause.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 77b0f5d (KVM: nVMX: Ack and write vector info to intr_info
if L1 asks us to), "Acknowledge interrupt on exit" behavior can be
emulated. To do so, KVM will ask the APIC for the interrupt vector if
during a nested vmexit if VM_EXIT_ACK_INTR_ON_EXIT is set. With APICv,
kvm_get_apic_interrupt would return -1 and give the following WARNING:
To fix this, we cannot rely on the processor's virtual interrupt delivery,
because "acknowledge interrupt on exit" must only update the virtual
ISR/PPR/IRR registers (and SVI, which is just a cache of the virtual ISR)
but it should not deliver the interrupt through the IDT. Thus, KVM has
to deliver the interrupt "by hand", similar to the treatment of EOI in
commit fc57ac2c9ca8 (KVM: lapic: sync highest ISR to hardware apic on
EOI, 2014-05-14).
The patch modifies kvm_cpu_get_interrupt to always acknowledge an
interrupt; there are only two callers, and the other is not affected
because it is never reached with kvm_apic_vid_enabled() == true. Then it
modifies apic_set_isr and apic_clear_irr to update SVI and RVI in addition
to the registers.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Suggested-by: "Zhang, Yang Z" <yang.z.zhang@intel.com> Tested-by: Liu, RongrongX <rongrongx.liu@intel.com> Tested-by: Felipe Reyes <freyes@suse.com> Fixes: 77b0f5d67ff2781f36831cba79674c3e97bd7acf Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the EOI exit bitmap (used for APICv) does not include
interrupts that are masked. However, this can cause a bug that manifests
as an interrupt storm inside the guest. Alex Williamson reported the
bug and is the one who really debugged this; I only wrote the patch. :)
The scenario involves a multi-function PCI device with OHCI and EHCI
USB functions and an audio function, all assigned to the guest, where
both USB functions use legacy INTx interrupts.
As soon as the guest boots, interrupts for these devices turn into an
interrupt storm in the guest; the host does not see the interrupt storm.
Basically the EOI path does not work, and the guest continues to see the
interrupt over and over, even after it attempts to mask it at the APIC.
The bug is only visible with older kernels (RHEL6.5, based on 2.6.32
with not many changes in the area of APIC/IOAPIC handling).
Alex then tried forcing bit 59 (corresponding to the USB functions' IRQ)
on in the eoi_exit_bitmap and TMR, and things then work. What happens
is that VFIO asserts IRQ11, then KVM recomputes the EOI exit bitmap.
It does not have set bit 59 because the RTE was masked, so the IOAPIC
never sees the EOI and the interrupt continues to fire in the guest.
My guess was that the guest is masking the interrupt in the redirection
table in the interrupt routine, i.e. while the interrupt is set in a
LAPIC's ISR, The simplest fix is to ignore the masking state, we would
rather have an unnecessary exit rather than a missed IRQ ACK and anyway
IOAPIC interrupts are not as performance-sensitive as for example MSIs.
Alex tested this patch and it fixed his bug.
[Thanks to Alex for his precise description of the problem
and initial debugging effort. A lot of the text above is
based on emails exchanged with him.]
Reported-by: Alex Williamson <alex.williamson@redhat.com> Tested-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return unhandlable error on inter-privilege level ret instruction. This is
since the current emulation does not check the privilege level correctly when
loading the CS, and does not pop RSP/SS as needed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ I'm currently running my tests on it now, and so far, after a few
hours it has yet to blow up. I'll run it for 24 hours which it never
succeeded in the past. ]
The tracing code has a way to make directories within the debugfs file
system as well as deleting them using mkdir/rmdir in the instance
directory. This is very limited in functionality, such as there is
no renames, and the parent directory "instance" can not be modified.
The tracing code creates the instance directory from the debugfs code
and then replaces the dentry->d_inode->i_op with its own to allow
for mkdir/rmdir to work.
When these are called, the d_entry and inode locks need to be released
to call the instance creation and deletion code. That code has its own
accounting and locking to serialize everything to prevent multiple
users from causing harm. As the parent "instance" directory can not
be modified this simplifies things.
I created a stress test that creates several threads that randomly
creates and deletes directories thousands of times a second. The code
stood up to this test and I submitted it a while ago.
Recently I added a new test that adds readers to the mix. While the
instance directories were being added and deleted, readers would read
from these directories and even enable tracing within them. This test
was able to trigger a bug:
Where the child->d_u.d_child seemed to be corrupted. I added lots of
trace_printk()s to see what was wrong, and sure enough, it was always
the child's d_u.d_child field. I looked around to see what touches
it and noticed that in __dentry_kill() which calls dentry_free():
static void dentry_free(struct dentry *dentry)
{
/* if dentry was never visible to RCU, immediate free is OK */
if (!(dentry->d_flags & DCACHE_RCUACCESS))
__d_free(&dentry->d_u.d_rcu);
else
call_rcu(&dentry->d_u.d_rcu, __d_free);
}
I also noticed that __dentry_kill() unlinks the child->d_u.child
under the parent->d_lock spin_lock.
Looking back at the loop in debugfs_remove_recursive() it never takes the
parent->d_lock to do the list walk. Adding more tracing, I was able to
prove this was the issue:
The dentry_kill freed ffff88006d573600 just as the remove recursive was walking
it.
In order to fix this, the list walk needs to be modified a bit to take
the parent->d_lock. The safe version is no longer necessary, as every
time we remove a child, the parent->d_lock must be released and the
list walk must start over. Each time a child is removed, even though it
may still be on the list, it should be skipped by the first check
in the loop:
if (!debugfs_positive(child))
continue;
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt handler in the ux500 crypto driver has an obviously
incorrect way to access the data buffer, which for a while has
caused this build warning:
../ux500/cryp/cryp_core.c: In function 'cryp_interrupt_handler':
../ux500/cryp/cryp_core.c:234:5: warning: passing argument 1 of '__fswab32' makes integer from pointer without a cast [enabled by default]
writel_relaxed(ctx->indata,
^
In file included from ../include/linux/swab.h:4:0,
from ../include/uapi/linux/byteorder/big_endian.h:12,
from ../include/linux/byteorder/big_endian.h:4,
from ../arch/arm/include/uapi/asm/byteorder.h:19,
from ../include/asm-generic/bitops/le.h:5,
from ../arch/arm/include/asm/bitops.h:340,
from ../include/linux/bitops.h:33,
from ../include/linux/kernel.h:10,
from ../include/linux/clk.h:16,
from ../drivers/crypto/ux500/cryp/cryp_core.c:12:
../include/uapi/linux/swab.h:57:119: note: expected '__u32' but argument is of type 'const u8 *'
static inline __attribute_const__ __u32 __fswab32(__u32 val)
There are at least two, possibly three problems here:
a) when writing into the FIFO, we copy the pointer rather than the
actual data we want to give to the hardware
b) the data pointer is an array of 8-bit values, while the FIFO
is 32-bit wide, so both the read and write access fail to do
a proper type conversion
c) This seems incorrect for big-endian kernels, on which we need to
byte-swap any register access, but not normally FIFO accesses,
at least the DMA case doesn't do it either.
This converts the bogus loop to use the same readsl/writesl pair
that we use for the two other modes (DMA and polling). This is
more efficient and consistent, and probably correct for endianess.
The bug has existed since the driver was first merged, and was
probably never detected because nobody tried to use interrupt mode.
It might make sense to backport this fix to stable kernels, depending
on how the crypto maintainers feel about that.
When a tty is opened for the serial console, the termios c_cflag
settings are inherited from the console line settings.
However, if the tty is subsequently closed, the termios settings
are lost. This results in a garbled console if the console is later
suspended and resumed.
Preserve the termios c_cflag for the serial console when the tty
is shutdown; this reflects the most recent line settings.
Fixes: Bugzilla #69751, 'serial console does not wake from S3' Reported-by: Valerio Vanni <valerio.vanni@inwind.it> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a failure while allocating the preallocation structure, a
number of blocks can end up getting marked in the in-memory buddy
bitmap, and then not getting released. This can result in the
following corruption getting reported by the kernel:
EXT4-fs error (device sda3): ext4_mb_generate_buddy:758: group 1126,
12793 clusters in bitmap, 12729 in gd
In that case, we need to release the blocks using mb_free_blocks().
Tested: fs smoke test; also demonstrated that with injected errors,
the file system is no longer getting corrupted
Most device drivers do call 'tpm_do_selftest' which executes a
TPM_ContinueSelfTest. tpm_i2c_stm_st33 is just pointlessly different,
I think it is bug.
These days we have the general assumption that the TPM is usable by
the kernel immediately after the driver is finished, so we can no
longer defer the mandatory self test to userspace.
Reported-by: Richard Marciel <rmaciel@linux.vnet.ibm.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Voltage limits, fan minimum speed, pwm frequency, pwm ramp rate, and
other attributes have the same problem, fix them as well.
Zone temperature limits are signed, but were cached as u8, causing
unepected values to be reported for negative temperatures. Cache as
s8 to fix the problem.
vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
[Guenter Roeck: Fix zone temperature cache] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code uses data_rate as array index in ads1015_read_adc() and uses pga
as array index in ads1015_reg_to_mv, so we must make sure both data_rate and
pga settings are in valid value range.
Return -EINVAL if the setting is out-of-range.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Temperature limit register writes did not account for negative numbers.
As a result, writing -127000 resulted in -126000 written into the
temperature limit register. This problem affected temp[1-3]_min,
temp[1-3]_max, temp[1-3]_auto_temp_crit, and temp[1-3]_auto_temp_min.
When writing pwm[1-3]_freq, a long variable was auto-converted into an int
without range check. Wiring values larger than MAXINT resulted in unexpected
register values.
When writing temp[1-3]_auto_temp_max, an unsigned long variable was
auto-converted into an int without range check. Writing values larger than
MAXINT resulted in unexpected register values.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with sizeof(int) < sizeof(unsigned long), writing a rpm value
larger than MAXINT will result in unpredictable limit values written to the
chip. Avoid auto-conversion from unsigned long to int to fix the problem.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure mutex lock protects the read-modify-write period to prevent possible
race condition bug.
In additional, update data->valid should also be protected by the mutex lock.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regular randconfig nightly testing has detected problems with omapdrm.
omapdrm fails to build when the kernel is built to support 64-bit DMA
addresses and/or 64-bit physical addresses due to an assumption about
the width of these types.
Use %pad to print DMA addresses, rather than %x or %Zx (which is even
more wrong than %x). Avoid passing a uint32_t pointer into a function
which expects dma_addr_t pointer.
drivers/gpu/drm/omapdrm/omap_plane.c: In function 'omap_plane_pre_apply':
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_plane.c:145:2: error: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_plane.o] Error 1
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_get_paddr':
drivers/gpu/drm/omapdrm/omap_gem.c:794:4: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_describe':
drivers/gpu/drm/omapdrm/omap_gem.c:991:4: error: format '%Zx' expects argument of type 'size_t', but argument 7 has type 'dma_addr_t' [-Werror=format]
drivers/gpu/drm/omapdrm/omap_gem.c: In function 'omap_gem_init':
drivers/gpu/drm/omapdrm/omap_gem.c:1470:4: error: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Werror=format]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_gem.o] Error 1
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c: In function 'dmm_txn_append':
drivers/gpu/drm/omapdrm/omap_dmm_tiler.c:226:2: error: passing argument 3 of 'alloc_dma' from incompatible pointer type [-Werror]
make[5]: *** [drivers/gpu/drm/omapdrm/omap_dmm_tiler.o] Error 1
make[5]: Target `__build' not remade because of errors.
make[4]: *** [drivers/gpu/drm/omapdrm] Error 2
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cb8db5d45 (UAPI: (Scripted) Disintegrate arch/arm/include/asm) moved
these syscall comments out of their context into the UAPI headers. Fix this.
Fixes: cb8db5d4578a ("UAPI: (Scripted) Disintegrate arch/arm/include/asm") Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scheduler uses policy == -1 to preserve the current policy state to
implement sched_setparam(). But, as (int) -1 is equals to 0xffffffff,
it's matching the if (policy & SCHED_RESET_ON_FORK) on
_sched_setscheduler(). This match changes the policy value to an
invalid value, breaking the sched_setparam() syscall.
This patch checks policy == -1 before check the SCHED_RESET_ON_FORK flag.
Link must be reset in case the fw doesn't
respond to client disconnect request.
We did charge the timer only in irq path
from mei_cl_irq_close and not in mei_cl_disconnect
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ALC269 & co have many vendor-specific setups with COEF verbs.
However, some verbs seem specific to some codec versions and they
result in the codec stalling. Typically, such a case can be avoided
by checking the return value from reading a COEF. If the return value
is -1, it implies that the COEF is invalid, thus it shouldn't be
written.
This patch adds the invalid COEF checks in appropriate places
accessing ALC269 and its variants. The patch actually fixes the
resume problem on Acer AO725 laptop.
On some HP laptops, the mute led is controlled by codec gpio.
When some machine resume from s3/s4, the codec gpio data will be
cleared to 0 by BIOS:
Before suspend:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
After resume:
IO[3]: enable=1, dir=1, wake=0, sticky=0, data=0, unsol=0
To skip the AFG node to enter D3 can't fix this problem.
A workaround is to restore the gpio data when the system resume
back from s3/s4. It is safe even on the machines without this
problem.
BugLink: https://bugs.launchpad.net/bugs/1358116 Tested-by: Franz Hsieh <franz.hsieh@canonical.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CA0132 driver tries to reload the firmware at resume. Usually this
works since the firmware loader core caches the firmware contents by
itself. However, if the driver failed to load the firmwares
(e.g. missing files), reloading the firmware at resume goes through
the actual file loading code path, and triggers a kernel WARNING like:
WARNING: CPU: 10 PID:11371 at drivers/base/firmware_class.c:1105 _request_firmware+0x9ab/0x9d0()
For avoiding this situation, this patch makes CA0132 skipping the f/w
loading at resume when it failed at probe time.
Original patch fixed the original problem, but the sound was far too low
for most users. This patch references a compare matrix to allow the
volume levels to act normally. I personally tested this patch myself,
and volume levels returned to normal. Please see this discussion for
more details: https://bugzilla.kernel.org/show_bug.cgi?id=65251
Signed-off-by: Paul S McSpadden <fisch602@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
The EHCI packet buffer in/out threshold is programmable for Intel Quark X1000
USB host controller, and the default value is 0x20 dwords. The in/out threshold
can be programmed to 0x80 dwords (512 Bytes) to maximize the perfomrance,
but only when isochronous/interrupt transactions are not initiated by the USB
host controller. This patch is to reconfigure the packet buffer in/out
threshold as maximal as possible to maximize the performance, and 0x7F dwords
(508 Bytes) should be used because the USB host controller initiates
isochronous/interrupt transactions.
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>