Thomas Petazzoni [Tue, 22 Dec 2015 10:43:29 +0000 (11:43 +0100)]
dmaengine: mv_xor: add suspend/resume support
This commit adds suspend/resume support to the mv_xor driver. The
config and interrupt mask registers must be saved and restored, and
upon resume, the MBus windows configuration must also be done again.
Tested on Armada 388 GP, with a RAID 5 array, accessed before and
after a suspend to RAM cycle.
Based on work from Ofer Heifetz and Lior Amsalem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When commit 6f166312c6ea2 ("dmaengine: mv_xor: add support for a38x
command in descriptor mode") added support for the descriptor mode
available in Marvell Armada 38x and later SoCs, it added a new
function mv_chan_set_mode_to_desc() which allows to configure a XOR
channel to get the specific operation to be done from each individual
DMA descriptor.
However, this function was mainly a duplicate of the existing
mv_chan_set_mode(), with just the operation being different.
This commit re-organizes the code into a single mv_chan_set_mode()
function, which takes the operation mode as argument, and the
mv_xor_channel_add() function decides whether to use
XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Mon, 14 Dec 2015 20:47:40 +0000 (22:47 +0200)]
dmaengine: core: Introduce new, universal API to request a channel
The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Peter Ujfalusi [Mon, 14 Dec 2015 20:47:39 +0000 (22:47 +0200)]
dmaengine: core: Move and merge the code paths using private_candidate
Channel matching with private_candidate() is used in two paths, the error
checking is slightly different in them and they are duplicating code also.
Move the code under find_candidate() to provide consistent execution and
going to allow us to reuse this mode of channel lookup later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Damien.Horsley [Thu, 10 Dec 2015 15:07:23 +0000 (15:07 +0000)]
dmaengine: mdc: Correct terminate_all handling
Use of the CANCEL bit in mdc_terminate_all creates an
additional 'command done' to appear in the registers (in
addition to an interrupt).
In addition, there is a potential race between
mdc_terminate_all and the irq handler if a transfer
completes at the same time as the terminate all (presently
this results in an inappropriate warning).
To handle these issues, any outstanding 'command done'
events are cleared during mdc_terminate_all and the irq
handler takes no action when there are no new 'command done'
events.
Peter Ujfalusi [Wed, 16 Dec 2015 13:19:05 +0000 (15:19 +0200)]
dmaengine: edma: Add probe callback to edma_tptc_driver
Due to changes in device and platform code drivers w/o probe will fail to
load. This means that the devices for eDMA TPTCs are goign to be without
driver and omap hwmod code will turn them off after the kernel finished
loading:
[ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling
[ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling
This will prevent eDMA to work since the TPTCs are not enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Fixes: 34635b1accb9 ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc") Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Mans Rullgard [Thu, 17 Dec 2015 23:30:57 +0000 (23:30 +0000)]
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
If the "dma-channels" DT property is missing, the dw_dma_parse_dt()
function return NULL, but not before allocating memory for a struct
dw_dma_platform_data through devres. If the device supports parameter
detection, the probe still succeeds and the allocated memory is not
released until the device is removed.
Fix this by deferring the allocation until after checking the
"dma-channels" property.
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
'commit d8b468394fb7 ("dmaengine: Add STM32 DMA driver")' leads to the
following Smatch complaint:
drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending()
error: we previously assumed 'chan->desc' could be null (see line 560)
So, this patch fixes the unchecked dereference of chan->desc by returning
operation not permitted error when stm32_dma_start_transfer() does not
succeed to allocate a virtual channel descriptor.
As of commit 4baadb9e05c68962 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), the Renesas R-Car HPB-DMAC driver is no longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Simon Horman [Wed, 2 Dec 2015 05:53:54 +0000 (14:53 +0900)]
dmaengine: usb-dmac: Document SoC specific compatibility strings
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compatibility strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas USB DMA Controller driver to follow this convention.
Cc: devicetree@vger.kernel.org Acked-by: Rob Herring <robh@kernel.org> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Markus Elfring [Mon, 16 Nov 2015 21:00:28 +0000 (22:00 +0100)]
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
The variable "res" will eventually be set to a resource pointer from
a call of the d40_hw_detect_init(() function.
Thus let us omit the explicit initialisation at the beginning.
Jon Hunter [Fri, 13 Nov 2015 16:39:43 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Free interrupts before killing tasklets
On probe failure or driver removal, before killing any tasklets, ensure
that the channel interrupt is freed to ensure that another channel
interrupt cannot occur and schedule the tasklet again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jon Hunter [Fri, 13 Nov 2015 16:39:42 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
The tegra20-apb-dma driver currently uses the flag GFP_ATOMIC when
allocating memory for structures used in conjunction with the DMA
descriptors. It is preferred that dmaengine drivers use GFP_NOWAIT
instead and so the emergency memory pool will not be used by these
drivers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jon Hunter [Fri, 13 Nov 2015 16:39:41 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Only save channel state for those in use
Currently the tegra-apb DMA driver suspend/resume helpers, save and
restore the registers for all channels regardless of whether they are
in use or not. Change this so that only channels that have been
allocated and configured are saved and restored.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jon Hunter [Fri, 13 Nov 2015 16:39:40 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Save and restore word count
Newer tegra devices have a separate word count register per channel that
contains the number of words to be transferred. This register is not
saved or restored by the suspend/resume helpers for these newer devices
and so ensure that it is.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jon Hunter [Fri, 13 Nov 2015 16:39:39 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Use dev_get_drvdata()
In the tegra_dma_runtime_suspend/resume functions, the pdev structure
is not needed, and so just call dev_get_drvdata() to get the device
data structure.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jon Hunter [Fri, 13 Nov 2015 16:39:38 +0000 (16:39 +0000)]
dmaengine: tegra-apb: Correct runtime-pm usage
The tegra-apb DMA driver enables runtime-pm but never calls
pm_runtime_get/put and hence the runtime-pm callbacks are never invoked.
The driver manages the clocks by directly calling clk_prepare_enable()
and clk_unprepare_disable().
Fix this by replacing the clk_prepare_enable() and clk_disable_unprepare()
with pm_runtime_get_sync() and pm_runtime_put(), respectively. Note that
the consequence of this is that if runtime-pm is disabled, then the clocks
will remain on the entire time the driver is loaded. However, if
runtime-pm is disabled, then power is not most likely not a concern.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: img-mdc: Remove unnecessary synchronize_irq() before devm_free_irq()
Calling synchronize_irq() right before devm_free_irq() is quite useless. On
one hand the IRQ can easily fire again before devm_free_irq() is entered,
on the other hand devm_free_irq() itself calls synchronize_irq() internally
(in a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq, dev;
@@
-synchronize_irq(irq);
devm_free_irq(dev, irq, ...);
// </smpl>
dmaengine: at_xdmac: Remove unnecessary synchronize_irq() before free_irq()
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Andy Shevchenko [Tue, 17 Nov 2015 16:00:30 +0000 (18:00 +0200)]
dmaengine: hsu: speed up residue calculation
There is no need to calculate an overall length of the descriptor each time we
call for DMA transfer status. Instead we do this at descriptor allocation stage
and keep the stored length for further usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Shevchenko [Tue, 17 Nov 2015 11:37:10 +0000 (13:37 +0200)]
dmaengine: idma64: use local variable to index descriptor
Since a local variable contains the number of hardware desriptors at the
beginning of idma64_desc_fill() we may use it to index the last descriptor as
well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Shevchenko [Tue, 17 Nov 2015 11:37:07 +0000 (13:37 +0200)]
dmaengine: idma64: drop IRQ enable / disable in handler
There is no need to disable interrupts in the IRQ handler. The driver
guarantess that at one time only one descriptor is active, besides the fact
that each call to the same channel will be serialized in idma64_chan_irq()
handler anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: at_xdmac: fix spurious flag status for mem2mem transfers
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
dmaengine: Add might_sleep() to dmaengine_synchronize()
Implementations of dmaengine_synchronize() are allowed to sleep, hence the
function must not be called to from atomic context. Add might_sleep() to
dmaengine_synchronize() to make it easier to detect non-compliant callers.
dmaengine: usb-dmac: fix endless loop in usb_dmac_chan_terminate_all()
This patch fixes an issue that list_for_each_entry() in
usb_dmac_chan_terminate_all() is possible to cause endless loop because
this will move own desc to the desc_freed. So, this driver should use
list_for_each_entry_safe() instead of list_for_each_entry().
Peter Ujfalusi [Wed, 11 Nov 2015 10:37:58 +0000 (12:37 +0200)]
dmaengine: omap-dma: Handle cases when the channel is polled for completion
When a DMA client driver decides that it is not providing callback for
completion of a transfer (and/or does not set the DMA_PREP_INTERRUPT) but
it will poll the status of the transfer (in case of short memcpy for
example) we will not get interrupt for the completion of the transfer and
will not mark the transaction as done.
Check the channel enable bit in the CCR when the status is queried and if
the channel is no longer active, we call the omap_dma_callback() to handle
the transfer completion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Wed, 11 Nov 2015 10:37:57 +0000 (12:37 +0200)]
dmaengine: omap-dma: Remove tasklet to start the transfers
The use of tasklet to actually start the DMA transfer slightly decreases the
DMA throughput since it adds small scheduling delay when the transfer is
started. In normal use, even with high I/O load the tasklet would start
one transaction at a time, however running the DMAtest for memcpy on all
available channels will cause the tasklet to start about 15 transfers.
The performance numbers on OMAP4 PandaBoard-es (test_buf_size = 6553):
With the tasklet:
dmatest: dma0chan30-copy: summary 5000 tests, 0 failures 186 iops 593 KB/s (0)
dmatest: dma0chan8-copy0: summary 5000 tests, 0 failures 184 iops 584 KB/s (0)
dmatest: dma0chan13-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan12-copy: summary 5000 tests, 0 failures 184 iops 585 KB/s (0)
dmatest: dma0chan7-copy0: summary 5000 tests, 0 failures 183 iops 581 KB/s (0)
Peter Ujfalusi [Fri, 30 Oct 2015 08:00:37 +0000 (10:00 +0200)]
dmaengine: ti-dma-crossbar: dra7: Support for reserving DMA event ranges
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peter Ujfalusi [Fri, 30 Oct 2015 08:00:36 +0000 (10:00 +0200)]
dmaengine: ti-dma-crossbar: dra7: Use bitops instead of idr
The use of idr was nice, but it was a bit heavy and we did not need the
features it provides. Using simple bitmap to track allocated DMA channels
is adequate here and it will be easier to add support for reserving
channels later on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dave Jiang [Fri, 6 Nov 2015 20:24:01 +0000 (13:24 -0700)]
dmaengine: IOATDMA: Cleanup pre v3.0 chansts register reads
Remove pre-3.0 channel status reads. 3.0 and later chansts register
is 64bit and can be read 64bit. This was clarified with the hardware
architects and since the driver now only support 3.0+ we don't need the
legacy support
Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Robert Jarzmik [Tue, 13 Oct 2015 19:54:29 +0000 (21:54 +0200)]
dmaengine: enable DMA_CTRL_REUSE
In the current state, the capability of transfer reuse can neither be
set by a slave dmaengine driver, nor used by a client driver, because
the capability is not available to dma_get_slave_caps().
Fix this by adding a way to declare the capability.
Robert Jarzmik [Tue, 13 Oct 2015 19:54:28 +0000 (21:54 +0200)]
dmaengine: virt-dma: don't always free descriptor upon completion
This patch attempts to enhance the case of a transfer submitted multiple
times, and where the cost of creating the descriptors chain is not
negligible.
This happens with big video buffers (several megabytes, ie. several
thousands of linked descriptors in one scatter-gather list). In these
cases, a video driver would want to do :
- tx = dmaengine_prep_slave_sg()
- dma_engine_submit(tx);
- dma_async_issue_pending()
- wait for video completion
- read video data (or not, skipping a frame is also possible)
- dma_engine_submit(tx)
=> here, the descriptors chain recalculation will take time
=> the dma coherent allocation over and over might create holes in
the dma pool, which is counter-productive.
- dma_async_issue_pending()
- etc ...
In order to cope with this case, virt-dma is modified to prevent freeing
the descriptors upon completion if DMA_CTRL_REUSE flag is set in the
transfer.
This patch is a respin of the former DMA_CTRL_ACK approach, which was
reverted due to a regression in audio drivers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ALSA: pcm_dmaengine: Properly synchronize DMA on shutdown
Use the new dmaengine_synchronize() function to make sure that all complete
callbacks have finished running before the runtime data, which is accessed
in the completed callback, is freed.
This fixes a long standing use-after-free race condition that has been
observed on some systems.
Implement the new device_synchronize() callback to allow proper
synchronization when stopping a channel. Since the driver already makes
sure that no new complete callbacks are scheduled after the
device_terminate_all() callback has been called, all left to do in the
device_synchronize() callback is to wait for all currently running complete
callbacks to finish.
dmaengine: virt-dma: Add synchronization helper function
Add a synchronize helper function for the virt-dma library. The function
makes sure that any scheduled descriptor complete callbacks have finished
running before the function returns.
This needs to be called by drivers using virt-dma in their
device_synchronize() callback. Depending on the driver additional
operations might be necessary in addition to calling vchan_synchronize() to
ensure proper synchronization.
dmaengine: Add transfer termination synchronization support
The DMAengine API has a long standing race condition that is inherent to
the API itself. Calling dmaengine_terminate_all() is supposed to stop and
abort any pending or active transfers that have previously been submitted.
Unfortunately it is possible that this operation races against a currently
running (or with some drivers also scheduled) completion callback.
Since the API allows dmaengine_terminate_all() to be called from atomic
context as well as from within a completion callback it is not possible to
synchronize to the execution of the completion callback from within
dmaengine_terminate_all() itself.
This means that a user of the DMAengine API does not know when it is safe
to free resources used in the completion callback, which can result in a
use-after-free race condition.
This patch addresses the issue by introducing an explicit synchronization
primitive to the DMAengine API called dmaengine_synchronize().
The existing dmaengine_terminate_all() is deprecated in favor of
dmaengine_terminate_sync() and dmaengine_terminate_async(). The former
aborts all pending and active transfers and synchronizes to the current
context, meaning it will wait until all running completion callbacks have
finished. This means it is only possible to call this function from
non-atomic context. The later function does not synchronize, but can still
be used in atomic context or from within a complete callback. It has to be
followed up by dmaengine_synchronize() before a client can free the
resources used in a completion callback.
In addition to this the semantics of the device_terminate_all() callback
are slightly relaxed by this patch. It is now OK for a driver to only
schedule the termination of the active transfer, but does not necessarily
have to wait until the DMA controller has completely stopped. The driver
must ensure though that the controller has stopped and no longer accesses
any memory when the device_synchronize() callback returns.
This was in part done since most drivers do not pay attention to this
anyway at the moment and to emphasize that this needs to be done when the
device_synchronize() callback is implemented. But it also helps with
implementing support for devices where stopping the controller can require
operations that may sleep.
Linus Torvalds [Sun, 15 Nov 2015 17:36:24 +0000 (09:36 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Mostly updates to the perf tool plus two fixes to the kernel core code:
- Handle tracepoint filters correctly for inherited events (Peter
Zijlstra)
- Prevent a deadlock in perf_lock_task_context (Paul McKenney)
- Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
Melo)
- Print full source file paths when using 'perf annotate --print-line
--full-paths' (Michael Petlan)
- Fix 'perf probe -d' when just one out of uprobes and kprobes is
enabled (Wang Nan)
- Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)
- Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
the 'perf test' LLVM entries, when running it in-tree, to
.gitignore (Yunlong Song)
- libbpf error reporting improvements, using a strerror interface to
more precisely tell the user about problems with the provided
scriptlet, be it in C or as a ready made object file (Wang Nan)
- Do not be case sensitive when searching for matching 'perf test'
entries (Arnaldo Carvalho de Melo)
- Inform the user about objdump failures in 'perf annotate' (Andi
Kleen)
- Improve the LLVM 'perf test' entry, introduce a new ones for BPF
and kbuild tests to check the environment used by clang to compile
.c scriptlets (Wang Nan)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
tools include: Add compiler.h to list.h
perf probe: Verify parameters in two functions
perf session: Add missing newlines to some pr_err() calls
perf annotate: Support full source file paths for srcline fix
perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
perf: Fix inherited events vs. tracepoint filters
perf: Disable IRQs across RCU RS CS that acquires scheduler lock
perf test: Do not be case sensitive when searching for matching tests
perf test: Add 'perf test BPF'
perf test: Enhance the LLVM tests: add kbuild test
perf test: Enhance the LLVM test: update basic BPF test program
perf bpf: Improve BPF related error messages
perf tools: Make fetch_kernel_version() publicly available
bpf tools: Add new API bpf_object__get_kversion()
bpf tools: Improve libbpf error reporting
perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
perf annotate: Inform the user about objdump failures in --stdio
perf stat: Make stat options global
perf sched latency: Fix thread pid reuse issue
...
Linus Torvalds [Sun, 15 Nov 2015 17:34:32 +0000 (09:34 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull liblockdep fixes from Thomas Gleixner:
"Three small patches to synchronize liblockdep with the latest core
changes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/liblockdep: explicitly declare lockdep API we call from liblockdep
tools/liblockdep: add userspace versions of WRITE_ONCE and RCU_INIT_POINTER
tools/liblockdep: remove task argument from debug_check_no_locks_held
Linus Torvalds [Sun, 15 Nov 2015 17:32:59 +0000 (09:32 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A couple of fixes and updates related to x86:
- Fix the W+X check regression on XEN
- The real fix for the low identity map trainwreck
- Probe legacy PIC early instead of unconditionally allocating legacy
irqs
- Add cpu verification to long mode entry
- Adjust the cache topology to AMD Fam17H systems
- Let Merrifield use the TSC across S3"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Call verify_cpu() after having entered long mode too
x86/setup: Fix low identity map for >= 2GB kernel range
x86/mm: Skip the hypervisor range when walking PGD
x86/AMD: Fix last level cache topology for AMD Fam17h systems
x86/irq: Probe for PIC presence before allocating descs for legacy IRQs
x86/cpu/intel: Enable X86_FEATURE_NONSTOP_TSC_S3 for Merrifield
Linus Torvalds [Sun, 15 Nov 2015 17:10:53 +0000 (09:10 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Linus Torvalds [Sat, 14 Nov 2015 17:43:00 +0000 (09:43 -0800)]
Merge tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc"
* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pci: depend on ZONE_DMA
ALSA: hda - Simplify phantom jack handling for HDMI/DP
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
ALSA: ctxfi: constify rsc ops structures
ALSA: usb: Add native DSD support for Aune X1S
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
sound: fix check for error condition of register_chrdev()
Linus Torvalds [Sat, 14 Nov 2015 17:09:37 +0000 (09:09 -0800)]
Merge tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Found a couple of brown paper bag bugs with the prev pull request
(including a SMP build breakage report from Guenter). Since these are
urgent I also decided to send over a bunch of other pending fixes
which could have otherwise waited an rc or two.
Summary:
- A bunch of brown paper bag bugs (MAINTAINERS list email, SMP build
failure)
- cpu_relax() now compiler barrier for UP as well
- handling of userspace Bus Errors for ARCompact builds"
* tag 'arc-4.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix silly typo in MAINTAINERS file
ARC: cpu_relax() to be compiler barrier even for UP
ARC: use ASL assembler mnemonic
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
ARC: remove extraneous header include
ARCv2: lib: memcpy: use local symbols
Vineet Gupta [Mon, 9 Nov 2015 12:18:34 +0000 (17:48 +0530)]
ARC: cpu_relax() to be compiler barrier even for UP
cpu_relax() on ARC has been barrier only for SMP (and no-op for UP). Per
recent discussions, it is safer to make it a compiler barrier
unconditionally.
Vineet Gupta [Fri, 30 Oct 2015 19:52:51 +0000 (01:22 +0530)]
ARC: [arcompact] Handle bus error from userspace as Interrupt not exception
Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)
- So move mem_service exception handler from common code into ARCv2 code.
- In ARCompact code, define mem_service as L2 interrupt handler which
just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com> Tested-by: Ana Martins <amartins@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Sat, 14 Nov 2015 05:53:18 +0000 (21:53 -0800)]
Merge tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's the branch of chrome platform changes for v4.4. Some have been
queued up for the full 4.3 release cycle since I forgot to send them
in for that round (rebased early on to deal with fixes conflicts).
Most of these enable EC communication stuff -- Pixel 2015 support,
enabling building for ARM64 platforms, and a few fixes for memory
leaks.
There's also a patch in here to allow reading/writing the verified
boot context, which depends on a sysfs patch acked by Greg"
* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: Fix i2c-designware adapter name
platform/chrome: Support reading/writing the vboot context
sysfs: Support is_visible() on binary attributes
platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
platform/chrome: cros_ec: Fix leak in sequence_store()
platform/chrome: Enable Chrome platforms on 64-bit ARM
platform/chrome: cros_ec_dev - Add a platform device ID table
platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
platform/chrome: cros_ec_lpc - Use existing function to check EC result
platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"
Linus Torvalds [Sat, 14 Nov 2015 05:47:06 +0000 (21:47 -0800)]
Merge tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull another x86 platform driver update from Darren Hart:
"Support for the unfortunately rather unique ESC key on the Ideapad
Yoga 3 and two DMI matches for rfkill support. Solitary fix for
potential missed errors for asus-wmi. Downgrade a thinkpad_acpi
message to info.
asus-wmi:
- fix error handling in store_sys_wmi()
ideapad-laptop:
- Add Lenovo Yoga 900 to no_hw_rfkill dmi list
- include Yoga 3 1170 in add rfkill whitelist
- add support for Yoga 3 ESC key
thinkpad_acpi:
- Don't yell on unsupported brightness interfaces"
* tag 'platform-drivers-x86-v4.4-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
asus-wmi: fix error handling in store_sys_wmi()
ideapad-laptop: Add Lenovo Yoga 900 to no_hw_rfkill dmi list
ideapad-laptop: include Yoga 3 1170 in add rfkill whitelist
ideapad-laptop: add support for Yoga 3 ESC key
thinkpad_acpi: Don't yell on unsupported brightness interfaces
Linus Torvalds [Sat, 14 Nov 2015 05:41:14 +0000 (21:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"An update to the tsc2005 driver that allows it to also support tsc2004
(basically the same controller, but uses i2c instead of spi bus), and
a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: parkbd - drop bogus __init from parkbd_allocate_serio()
Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
Input: tsc2004 - add support for tsc2004
Input: tsc200x-core - rename functions and variables
Input: tsc2005 - separate SPI and core functions
Linus Torvalds [Sat, 14 Nov 2015 04:35:54 +0000 (20:35 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
Linus Torvalds [Sat, 14 Nov 2015 04:04:17 +0000 (20:04 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c2f ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f78
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
Now that the xattr handler is passed to the xattr handler operations, we
have access to the attribute name prefix, so simplify
f2fs_xattr_generic_list.
Also, f2fs_xattr_advise_list is only ever called for
f2fs_xattr_advise_handler; there is no need to double check for that.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Jaegeuk Kim <jaegeuk@kernel.org> Cc: Changman Lee <cm224.lee@samsung.com> Cc: Chao Yu <chao2.yu@samsung.com> Cc: linux-f2fs-devel@lists.sourceforge.net Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that the xattr handler is passed to the xattr handler operations, we
have access to the attribute name prefix, so simplify the squashfs xattr
handlers a bit.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Phillip Lougher <phillip@squashfs.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that the xattr handler is passed to the xattr handler operations, we
can use the same get and set operations for the user, trusted, and security
xattr namespaces. In those namespaces, we can access the full attribute
name by "reattaching" the name prefix the vfs has skipped for us. Add a
xattr_full_name helper to make this obvious in the code.
For the "system.posix_acl_access" and "system.posix_acl_default"
attributes, handler->prefix is the full attribute name; the suffix is the
empty string.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: v9fs-developer@lists.sourceforge.net Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
xattr handlers: Pass handler to operations instead of flags
The xattr_handler operations are currently all passed a file system
specific flags value which the operations can use to disambiguate between
different handlers; some file systems use that to distinguish the xattr
namespace, for example. In some oprations, it would be useful to also have
access to the handler prefix. To allow that, pass a pointer to the handler
to operations instead of the flags value alone.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
jffs2: Add missing capability check for listing trusted xattrs
The vfs checks if a task has the appropriate access for get and set
operations, but it cannot do that for the list operation; the file system
must check for that itself.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: David Woodhouse <dwmw2@infradead.org> Cc: linux-mtd@lists.infradead.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ubifs installs a security xattr handler in sb->s_xattr but doesn't use the
generic_{get,set,list,remove}xattr inode operations needed for processing
this list of attribute handlers; the handler is never called. Instead,
ubifs uses its own xattr handlers which also process security xattrs.
Remove the dead code.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Richard Weinberger <richard@nod.at> Cc: Artem Bityutskiy <dedekind1@gmail.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: linux-mtd@lists.infradead.org Cc: Subodh Nijsure <snijsure@grid-net.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When a filesystem that contains POSIX ACLs is mounted without ACL support
(-o noacl), the appropriate behavior is not to list any existing POSIX ACL
xattrs. The return value for list xattr handlers in this case is 0, not an
error code: several filesystems that use the POSIX ACL xattr handlers do
not expect the list operation to fail.
Symlinks cannot have ACLs, so posix_acl_xattr_list will never be called for
symlinks in the first place.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
vfs: Check attribute names in posix acl xattr handers
The get and set operations of the POSIX ACL xattr handlers failed to check
the attribute names, so all names with "system.posix_acl_access" or
"system.posix_acl_default" as a prefix were accepted. Reject invalid names
from now on.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 14 Nov 2015 01:05:32 +0000 (17:05 -0800)]
Merge tag 'vfio-v4.4-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Use kernel interfaces for VPD emulation (Alex Williamson)
- Platform fix for releasing IRQs (Eric Auger)
- Type1 IOMMU always advertises PAGE_SIZE support when smaller mapping
sizes are available (Eric Auger)
- Platform fixes for incorrectly using copies of structures rather than
pointers to structures (James Morse)
- Rework platform reset modules, fix leak, and add AMD xgbe reset
module (Eric Auger)
- Fix vfio_device_get_from_name() return value (Joerg Roedel)
- No-IOMMU interface (Alex Williamson)
- Fix potential out of bounds array access in PCI config handling (Dan
Carpenter)
* tag 'vfio-v4.4-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: make an array larger
vfio: Include No-IOMMU mode
vfio: Fix bug in vfio_device_get_from_name()
VFIO: platform: reset: AMD xgbe reset module
vfio: platform: reset: calxedaxgmac: fix ioaddr leak
vfio: platform: add dev_info on device reset
vfio: platform: use list of registered reset function
vfio: platform: add compat in vfio_platform_device
vfio: platform: reset: calxedaxgmac: add reset function registration
vfio: platform: introduce module_vfio_reset_handler macro
vfio: platform: add capability to register a reset function
vfio: platform: introduce vfio-platform-base module
vfio/platform: store mapped memory in region, instead of an on-stack copy
vfio/type1: handle case where IOMMU does not support PAGE_SIZE size
VFIO: platform: clear IRQ_NOAUTOEN when de-assigning the IRQ
vfio/pci: Use kernel VPD access functions
vfio: Whitelist PCI bridges
Linus Torvalds [Sat, 14 Nov 2015 00:40:36 +0000 (16:40 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull SMB3 updates from Steve French:
"A collection of SMB3 patches adding some reliability features
(persistent and resilient handles) and improving SMB3 copy offload.
I will have some additional patches for SMB3 encryption and SMB3.1.1
signing (important security features), and also for improving SMB3
persistent handle reconnection (setting ChannelSequence number e.g.)
that I am still working on but wanted to get this set in since they
can stand alone"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
Allow copy offload (CopyChunk) across shares
Add resilienthandles mount parm
[SMB3] Send durable handle v2 contexts when use of persistent handles required
[SMB3] Display persistenthandles in /proc/mounts for SMB3 shares if enabled
[SMB3] Enable checking for continuous availability and persistent handle support
[SMB3] Add parsing for new mount option controlling persistent handles
Allow duplicate extents in SMB3 not just SMB3.1.1
Linus Torvalds [Sat, 14 Nov 2015 00:30:29 +0000 (16:30 -0800)]
Merge branch 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes and cleanups from Chris Mason:
"Some of this got cherry-picked from a github repo this week, but I
verified the patches.
We have three small scrub cleanups and a collection of fixes"
* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Use fs_info directly in btrfs_delete_unused_bgs
btrfs: Fix lost-data-profile caused by balance bg
btrfs: Fix lost-data-profile caused by auto removing bg
btrfs: Remove len argument from scrub_find_csum
btrfs: Reduce unnecessary arguments in scrub_recheck_block
btrfs: Use scrub_checksum_data and scrub_checksum_tree_block for scrub_recheck_block_checksum
btrfs: Reset sblock->xxx_error stats before calling scrub_recheck_block_checksum
btrfs: scrub: setup all fields for sblock_to_check
btrfs: scrub: set error stats when tree block spanning stripes
Btrfs: fix race when listing an inode's xattrs
Btrfs: fix race leading to BUG_ON when running delalloc for nodatacow
Btrfs: fix race leading to incorrect item deletion when dropping extents
Btrfs: fix sleeping inside atomic context in qgroup rescan worker
Btrfs: fix race waiting for qgroup rescan worker
btrfs: qgroup: exit the rescan worker during umount
Btrfs: fix extent accounting for partial direct IO writes
Linus Torvalds [Fri, 13 Nov 2015 17:24:40 +0000 (09:24 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"There are several patches from Ilya fixing RBD allocation lifecycle
issues, a series adding a nocephx_sign_messages option (and associated
bug fixes/cleanups), several patches from Zheng improving the
(directory) fsync behavior, a big improvement in IO for direct-io
requests when striping is enabled from Caifeng, and several other
small fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: clear msg->con in ceph_msg_release() only
libceph: add nocephx_sign_messages option
libceph: stop duplicating client fields in messenger
libceph: drop authorizer check from cephx msg signing routines
libceph: msg signing callouts don't need con argument
libceph: evaluate osd_req_op_data() arguments only once
ceph: make fsync() wait unsafe requests that created/modified inode
ceph: add request to i_unsafe_dirops when getting unsafe reply
libceph: introduce ceph_x_authorizer_cleanup()
ceph: don't invalidate page cache when inode is no longer used
rbd: remove duplicate calls to rbd_dev_mapping_clear()
rbd: set device_type::release instead of device::release
rbd: don't free rbd_dev outside of the release callback
rbd: return -ENOMEM instead of pool id if rbd_dev_create() fails
libceph: use local variable cursor instead of &msg->cursor
libceph: remove con argument in handle_reply()
ceph: combine as many iovec as possile into one OSD request
ceph: fix message length computation
ceph: fix a comment typo
rbd: drop null test before destroy functions
projects / linux-beck.git / log