Without this the IRQ base will not be correctly configured for the
subdevices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some newer device revisions add a second parent ID. Support this in
the device validity checks done at startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
The error message 'NMI watchdog failed to create perf event...'
does not make it clear that this is a fatal error for the
watchdog. It also currently prints the error value as a
pointer, rather than extracting the error code with PTR_ERR().
Fix that.
Add a note to the description of the 'nowatchdog' kernel
parameter to associate it with this message.
rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst. Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: Marco Stornelli <marco.stornelli@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the error-path where PM notifies PM_POST_RESTORE, the rescan-blockage
should be cleared as well. Otherwise it'll be never re-probed.
Also, as a bonus, this fixes a bug in S4 with user-mode suspend in the
current code, as it sends PM_POST_RESTORE instead of
PM_POST_HIBERNATION wrongly.
Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.
So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
Reported-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
The first bug will only show up with broken xHCI hosts with Extended
Capabilities registers that have duplicate port speed entries for the same
port. The idea with the original code was to set the port_array entry to
-1 if the duplicate port speed entry said the port was a different speed
than the original port speed entry. That would mean that later, the port
would not be exposed to the USB core. Unfortunately, I forgot a continue
statement, and the port_array entry would just be overwritten in the next
line.
The second bug would happen if there are conflicting port speed registers
(so that some entry in port_array is -1), or one of the hardware port
registers was not described in the port speed registers (so that some
entry in port_array is 0). The code that sets up the usb2_ports array
would accidentally claim those ports. That wouldn't really cause any
user-visible issues, but it is a bug.
This patch should go into the stable trees that have the port array and
USB 3.0 port disabling prevention patches.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Source:
http://www.linuxant.com/pipermail/driverloader/2005q3/002307.html
http://wireless.kernel.org/en/users/Drivers/p54/devices (by M. Davis)
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an unusual_devs entry for the Samsung YP-CP3 MP4 player.
User was getting the following errors in dmesg:
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: USB disconnect, address 2
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb:<2>ldm_validate_partition_table(): Disk read failed.
Dev sdb: unable to read RDB block 0
unable to read partition table
Signed-off-by: Vitaly Kuznetsov <vitty@altlinux.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The install_special_mapping routine (used, for example, to setup the
vdso) skips the security check before insert_vm_struct, allowing a local
attacker to bypass the mmap_min_addr security restriction by limiting
the available pages for special mappings.
bprm_mm_init() also skips the check, and although I don't think this can
be used to bypass any restrictions, I don't see any reason not to have
the security check.
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During initialization each driver reads the default TX power
for each individual channel. However mac80211 only accepts the
maximum value (which is also handled as default value).
As a result, the TX power of the device was being limited to
the default value, which is often quite low compared to the
real maximum acceptable value.
This patch allows each driver to set the maximum value on a
per-channel basis which is forwarded to mac80211. The default
value will be preserved for now, in case we want to update
mac80211 to differentiate between the maximum and default txpower.
This fixes bug complaining about limited TX power values like:
https://bugzilla.kernel.org/show_bug.cgi?id=16358
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com> Reported-by: Max Asbock <masbock@linux.vnet.ibm.com> Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <1291225233.2648.39.camel@sbsiddha-MOBL3> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Tested-by: Takao Indoh <indou.takao@jp.fujitsu.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).
Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.
Handle any previous faults after enabling the vt-d fault handling.
For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101201062244.630417138@intel.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.
Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()
A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <20101201062244.541996375@intel.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vdso Makefile passes linker-style -m options not to the linker but
to gcc. This happens to work with earlier gcc, but fails with gcc
4.6. Pass gcc-style -m options, instead.
Note: all currently supported versions of gcc supports -m32, so there
is no reason to conditionalize it any more.
Reported-by: H. J. Lu <hjl.tools@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The file_ops struct for the "trace" special file defined llseek as seq_lseek().
However, if the file was opened for writing only, seq_open() was not called,
and the seek would dereference a null pointer, file->private_data.
This patch introduces a new wrapper for seq_lseek() which checks if the file
descriptor is opened for reading first. If not, it does nothing.
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
Andreas Herrmann [Thu, 16 Dec 2010 20:29:37 +0000 (21:29 +0100)]
x86, amd: Fix panic on AMD CPU family 0x15
[The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.]
This CPU family check is not required -- existence of the NodeId MSR
is indicated by a CPUID feature flag which is already checked in
amd_fixup_dcm() -- and it needlessly prevents amd_fixup_dcm() to be
called for newer AMD CPUs.
In worst case this can lead to a panic in the scheduler code for AMD
family 0x15 multi-node AMD CPUs. I just have a picture of VGA console
output so I can't copy-and-paste it herein, but the call stack of such
a panic looked like:
The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If inotify_init is unable to allocate a new file for the new inotify
group we leak the new group. This patch drops the reference on the
group on file allocation failure.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are some situations (e.g. in __pm_generic_call()), where
pm_runtime_suspended() is used to decide whether or not to execute
a device's (system) ->suspend() callback. The callback is not
executed if pm_runtime_suspended() returns true, but it does so
for devices that don't even support runtime PM, because the
power.disable_depth device field is ignored by it. This leads to
problems (i.e. devices are not suspened when they should), so rework
pm_runtime_suspended() so that it returns false if the device's
power.disable_depth field is different from zero.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a long-running regression that proved difficult to fix and
which is hitting certain people and is rather annoying in its effects.
Damien reported that after 74f5187ac8 (sched: Cure load average vs
NO_HZ woes) his load average is unnaturally high, he also noted that
even with that patch reverted the load avgerage numbers are not
correct.
The problem is that the previous patch only solved half the NO_HZ
problem, it addressed the part of going into NO_HZ mode, not of
comming out of NO_HZ mode. This patch implements that missing half.
When comming out of NO_HZ mode there are two important things to take
care of:
- Folding the pending idle delta into the global active count.
- Correctly aging the averages for the idle-duration.
So with this patch the NO_HZ interaction should be complete and
behaviour between CONFIG_NO_HZ=[yn] should be equivalent.
Furthermore, this patch slightly changes the load average computation
by adding a rounding term to the fixed point multiplication.
wake_up_klogd() may get called from preemptible context but uses
__raw_get_cpu_var() to write to a per cpu variable. If it gets preempted
between getting the address and writing to it, the cpu in question could be
offline if the process gets scheduled back and hence writes to the per cpu data
of an offline cpu.
This buggy behaviour was introduced with fa33507a "printk: robustify
printk, fix #2" which was supposed to fix a "using smp_processor_id() in
preemptible" warning.
Let's use this_cpu_write() instead which disables preemption and makes sure
that the outlined scenario cannot happen.
Some Panasonic Toughbooks create nodes in module level code.
Module level code is the executable AML code outside of control method,
for example, below AML code creates a node \_SB.PCI0.GFX0.DD02.CUBL
If (\_OSI ("Windows 2006"))
{
Scope (\_SB.PCI0.GFX0.DD02)
{
Name (CUBL, Ones)
...
}
}
Scope() op does not actually create a new object, it refers to an
existing object(\_SB.PCI0.GFX0.DD02 in above example). However, for
Scope(), we want to indeed open a new scope, so the child nodes(CUBL in
above example) can be created correctly under it.
https://bugzilla.kernel.org/show_bug.cgi?id=19462
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
Reported-by: Gorik Van Steenberge <gvs@zemos.net> Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info> Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Reported-by: Pawel Staszewski <pstaszewski@artcom.pl> Diagnosed-by: Andrej Ota <andrej@ota.si> Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com> Tested-by: Pawel Staszewski <pstaszewski@artcom.pl> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Andrej Ota <andrej@ota.si> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
packet_getname_spkt() doesn't initialize all members of sa_data field of
sockaddr struct if strlen(dev->name) < 13. This structure is then copied
to userland. It leads to leaking of contents of kernel stack memory.
We have to fully fill sa_data with strncpy() instead of strlcpy().
The same with packet_getname(): it doesn't initialize sll_pkttype field of
sockaddr_ll. Set it to zero.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit c1f19b51d1d8 (net: support time stamping in phy devices.),
kernel might crash if CONFIG_NETWORK_PHY_TIMESTAMPING=y and
skb_defer_rx_timestamp() handles a packet without an ethernet header.
Fixes kernel bugzilla #24102
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=24102 Reported-and-tested-by: Andrew Watts <akwatts@ymail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Parameter 'len' is size_t type so it will never get negative.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Followup of commit ef885afbf8a37689 (net: use rcu_barrier() in
rollback_registered_many)
dst_dev_event() scans a garbage dst list that might be feeded by various
network notifiers at device dismantle time.
Its important to call dst_dev_event() after other notifiers, or we might
enter the infamous msleep(250) in netdev_wait_allrefs(), and wait one
second before calling again call_netdevice_notifiers(NETDEV_UNREGISTER,
dev) to properly remove last device references.
Use priority -10 to let dst_dev_notifier be called after other network
notifiers (they have the default 0 priority)
Reported-by: Ben Greear <greearb@candelatech.com> Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reported-by: Octavian Purdila <opurdila@ixiacom.com> Reported-by: Benjamin LaHaise <bcrl@kvack.org> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x25 does not decrement the network device reference counts on module unload.
Thus unregistering any pre-existing interface after unloading the x25 module
hangs and results in
unregister_netdevice: waiting for tap0 to become free. Usage count = 1
This patch decrements the reference counts of all interfaces in x25_link_free,
the way it is already done in x25_link_device_down for NETDEV_DOWN events.
Signed-off-by: Apollon Oikonomopoulos <apollon@noc.grnet.gr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we break the loop when there are still skbs in tq and no skb in
rq, the skbs will be left in txq until new skbs are enqueued into rq.
In rare cases, no new skb is queued, then these skbs will stay in rq
forever.
After this patch, if tq isn't empty when we break the loop, we goto
resched directly.
Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unconditional use of skb->dev won't work here,
try to fetch the econet device via skb_dst()->dev
instead.
Suggested by Eric Dumazet.
Reported-by: Nelson Elhage <nelhage@ksplice.com> Tested-by: Nelson Elhage <nelhage@ksplice.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to drop the mutex and do a dev_put, so set an error code and break like
the other paths, instead of returning directly.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavel Emelyanov tried to fix a race between sk_filter_(de|at)tach and
sk_clone() in commit 47e958eac280c263397
Problem is we can have several clones sharing a common sk_filter, and
these clones might want to sk_filter_attach() their own filters at the
same time, and can overwrite old_filter->rcu, corrupting RCU queues.
We can not use filter->rcu without being sure no other thread could do
the same thing.
Switch code to a more conventional ref-counting technique : Do the
atomic decrement immediately and queue one rcu call back when last
reference is released.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somewhere along the lines net_cls_subsys_id became a macro when
cls_cgroup is built as a module. Not only did it make cls_cgroup
completely useless, it also causes it to crash on module unload.
This patch fixes this by removing that macro.
Thanks to Eric Dumazet for diagnosing this problem.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a missing ntohs() for bridge IPv6 multicast snooping.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regarding benet be_cmd_multicast_set() function, now using
netdev_for_each_mc_addr() helper for mac address copy, but
when copying to req->mac[] did not increase of the index.
Cc: Sathya Perla <sathyap@serverengines.com> Cc: Subbu Seetharaman <subbus@serverengines.com> Cc: Sarveshwar Bandi <sarveshwarb@serverengines.com> Cc: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: Joe Jin <joe.jin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes ax25_getname() doesn't initialize all members of fsa_digipeater
field of fsa struct, also the struct has padding bytes between
sax25_call and sax25_ndigis fields. This structure is then copied to
userland. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.
lkml ref : http://lkml.org/lkml/2010/11/25/8
This mechanism is used in applications, one choice we have is to have a
recursion limit.
Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.
Add a recursion_level to unix socket, allowing up to 4 levels.
Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As device_set_wakeup_enable can now sleep, move the call to outside
the critical section.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am not family with RealTek RTL-8139C+ series 10/100 PCI Ethernet driver.
I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(status & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If these are right, driver will set ip_summed with CHECKSUM_UNNECESSARY for other
upper protocol, e.g. sctp, igmp protocol. This will cause protocol stack ignores
checksum check for packets with invalid checksum.
This patch is only compile-test.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure sysctl_tcp_cookie_size is read once in
tcp_cookie_size_check(), or we might return an illegal value to caller
if sysctl_tcp_cookie_size is changed by another cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: William Allen Simpson <william.allen.simpson@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysctl_tcp_tso_win_divisor might be set to zero while one cpu runs in
tcp_tso_should_defer(). Make sure we dont allow a divide by zero by
reading sysctl_tcp_tso_win_divisor exactly once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bug has to do with boundary checks on the initial receive window.
If the initial receive window falls between init_cwnd and the
receive window specified by the user, the initial window is incorrectly
brought down to init_cwnd. The correct behavior is to allow it to
remain unchanged.
Signed-off-by: Nandita Dukkipati <nanditad@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As noted by Steve Chen, since commit f5fff5dc8a7a3f395b0525c02ba92c95d42b7390 ("tcp: advertise MSS
requested by user") we can end up with a situation where
tcp_select_initial_window() does a divide by a zero (or
even negative) mss value.
The problem is that sometimes we effectively subtract
TCPOLEN_TSTAMP_ALIGNED and/or TCPOLEN_MD5SIG_ALIGNED from the mss.
Fix this by increasing the minimum from 8 to 64.
Reported-by: Steve Chen <schen@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9e7366609d640ff4040304ea197fbc618
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")
The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.
Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net> CC: Damian Lukowski <damian@tvk.rwth-aachen.de> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sparc64 systems have a restriction in that passing in buffer
addressses above 4GB to prom calls is not reliable.
We end up violating this when we do prom console writes, because we
use an on-stack buffer to translate '\n' into '\r\n'.
So instead, do this translation into an intermediate buffer, which is
in the kernel image and thus below 4GB, then pass that to the PROM
console write calls.
On the 32-bit side we don't have to deal with any of these issues, so
the new prom_console_write_buf() uses the existing prom_nbputchar()
implementation. However we can now mark those routines static.
Since the 64-bit side completely uses new code we can delete the
putchar bits as they are now completely unused.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This gets us closer to being able to eliminate the use
of dynamic and stack based buffers, so that we can adhere
to the "no buffer addresses above 4GB" rule for PROM calls.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.
Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.
It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Signed-off-by: Matteo Croce <matteo@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Le dimanche 05 décembre 2010 à 12:23 +0100, Eric Dumazet a écrit :
> Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :
>
> > Hmm..
> >
> > If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> > in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> > that your patch can be applied.
> >
> > Right now it is not good, because RTNL wont be necessarly held when you
> > are going to call arp_invalidate() ?
>
> While doing this analysis, I found a refcount bug in llc, I'll send a
> patch for net-2.6
Oh well, of course I must first fix the bug in net-2.6, and wait David
pull the fix in net-next-2.6 before sending this rcu conversion.
Note: this patch should be sent to stable teams (2.6.34 and up)
[PATCH net-2.6] llc: fix a device refcount imbalance
commit abf9d537fea225 (llc: add support for SO_BINDTODEVICE) added one
refcount imbalance in llc_ui_bind(), because dev_getbyhwaddr() doesnt
take a reference on device, while dev_get_by_index() does.
Fix this using RCU locking. And since an RCU conversion will be done for
2.6.38 for dev_getbyhwaddr(), put the rcu_read_lock/unlock exactly at
their final place.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the host_to_fcp_swap call to correctly populate the LUN field
in the Command Type 6 path. This field is used during LUN reset
cleanup and must match the field used in the FCP command.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com> Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Signed-off-by: Valentine Barshak <vbarshak@mvista.com> Signed-off-by: George G. Davis <gdavis@mvista.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The user-space hibernation sends a wrong notification after the image
restoration because of thinko for the file flag check. RDONLY
corresponds to hibernation and WRONLY to restoration, confusingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In ib_uverbs_poll_cq() code there is a potential integer overflow if
userspace passes in a large cmd.ne. The calls to kmalloc() would
allocate smaller buffers than intended, leading to memory corruption.
There iss also an information leak if resp wasn't all used.
Unprivileged userspace may call this function, although only if an
RDMA device that uses this function is present.
Fix this by copying CQ entries one at a time, which avoids the
allocation entirely, and also by moving this copying into a function
that makes sure to initialize all memory copied to userspace.
Special thanks to Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
for his help and advice.
Signed-off-by: Dan Carpenter <error27@gmail.com>
[ Monkey around with things a bit to avoid bad code generation by gcc
when designated initializers are used. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alignment of alloc_bootmem() depends on the value of
L1_CACHE_SHIFT. What we need here, however, is 64 byte alignment. Use
alloc_bootmem_align() and explicitly specify the alignment instead.
This fixes a kernel boot crash reported by Jody when the cpu in .config
is set to MPENTIUMII but the kernel is booted on a xsave-capable CPU.
Reported-by: Jody Bruchon <jody@nctritech.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212442.059967454@sbsiddha-MOBL3.sc.intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an alloc_bootmem_align() interface to allocate bootmem with
specified alignment. This is necessary to be able to allocate the
xsave area in a subsequent patch.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20101116212441.977574826@sbsiddha-MOBL3.sc.intel.com> Acked-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log