Input: ADP5589 - new driver for I2C Keypad Decoder and I/O Expander
From http://www.analog.com/ADP5589:
The ADP5589 is an I/O port expander and keypad matrix decoder designed
for QWERTY type phones that require a large keypad matrix and expanded
I/O lines.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Thierry Reding [Tue, 17 May 2011 16:32:29 +0000 (09:32 -0700)]
Input: tsc2007 - add X, Y and Z fuzz factors to platform data
These new platform-specific values can be used to set the fuzz parameter
passed to the input_set_abs_params() function for the ABS_X, ABS_Y and
ABS_PRESSURE axes.
Thierry Reding [Tue, 17 May 2011 16:31:33 +0000 (09:31 -0700)]
Input: tsc2007 - add poll_delay parameter to platform data
Depending on the quality of the touch panel, the time for the X-, X+, Y-
and Y+ inputs to settle may vary. The poll_delay parameter can be used
to override the default of 1 millisecond.
Thierry Reding [Tue, 17 May 2011 16:31:01 +0000 (09:31 -0700)]
Input: tsc2007 - add max_rt parameter to platform data
Finger touch events or very quick stylus events on low-quality panels
can cause the tsc2007 to read bogus values. Looking at oscilloscope
snapshots, this seems to be caused by the touch event disappearing
during the measurements. These bogus values result in misclicks, where
the X and Y values deviate from the real position.
Most of these misclicks can be filtered out by setting a low enough
threshold for the maximum resistance (which is loosely the inverse of
the pressure) allowed to consider a set of values valid. Since this
behaviour is largely dependent on the type and quality of the panel,
this commit introduces the max_rt parameter. The default value is kept
at MAX_12BIT.
Thierry Reding [Tue, 17 May 2011 16:29:45 +0000 (09:29 -0700)]
Input: tsc2007 - debounce pressure measurement
When the controller signals a pen-down event via the platform-specific
GPIO, while the sample values indicate an invalid measurement, the
measurement needs to be repeated.
As reported by Jean-Francois Dagenais, the wheel algorithm caused a
divide by zero exception due to missing variable pre-initialization.
In fact it turned out that the whole algorithm had several problems.
It is therefore replaced with something that is known working.
Input: ad714x - fix threshold and completion interrupt masks
Fix two issues in the threshold and completion interrupt mask and unmask
functions. According to the AD714x datasheets the highest stage completion
interrupt should be enabled. Fix mask computation.
Éric Piel [Tue, 17 May 2011 05:45:54 +0000 (22:45 -0700)]
Input: elantech - remove support for proprietary X driver
Apparently somewhere someone had a proprietary X driver. To get the
multitouch info, it uses some hack on the normal API instead of using
the multitouch protocol. Now that the multitouch info is transmitted
correctly it makes not much sense to keep it. Especially because it's
impossible to find this proprietary X driver anywhere, so the number of
users must be very low.
Éric Piel [Tue, 17 May 2011 05:45:54 +0000 (22:45 -0700)]
Input: elantech - report multitouch with proper ABS_MT messages
Multitouch info was reported only via a old protocol used by the
proprietary X driver from elantech. Let's report the multitouch info
also following the official MT protocol. It's semi-mt because the device
only reports the lowest/highest coordinates.
This was done following the multi-touch-protocol.txt documentation, and
inspired by the bcm5974 and elantech implementations. Testing was light
as there is not many applications using this protocol yet, but the X
synaptics driver didn't complain and the X multitouch driver behaved
correctly.
Éric Piel [Tue, 17 May 2011 05:45:54 +0000 (22:45 -0700)]
Input: elantech - export pressure and width when supported
Using the info of the Dell/Ubuntu driver, described in the protocol
document, report both width and pressure when pressing 1 and 3
fingers, for the versions of the touchpad which support it.
Éric Piel [Tue, 17 May 2011 05:45:54 +0000 (22:45 -0700)]
Input: elantech - describe further the protocol
For some Dell laptops, Ubuntu had a special version of the elantech
driver with more knowledge on the devices. It can be found there:
http://zinc.ubuntu.com/git?p=mid-team/hardy-netbook.git;a=blob;f=drivers/input/mouse/elantech.c;h=d0e2cafed162428f72e3654f4dda85e08ea486b3;hb=refs/heads/abi-22
By inspecting the source code, and doing some test on a real hardware, I
have completed the protocol specification (especially for the 6 bytes
protocol). It also adds information about the mapping between the
version reported by the device and the protocol to use.
Rakesh Iyer [Wed, 11 May 2011 21:24:10 +0000 (14:24 -0700)]
Input: tegra-kbc - change wakeup logic to be all or nothing
Tegra hardware design cannot reliably support an arbitrary set of keys
waking up the system. Modify wakeup logic so either any key wakes the
system up or none will do.
Magnus Damm [Thu, 28 Apr 2011 16:34:32 +0000 (09:34 -0700)]
Input: sh_keysc - switch to threaded IRQ handler
Update the KEYSC driver to make use of threaded IRQs with IRQF_ONESHOT
to improve interrupt latency. The driver is using udelay() in the ISR
to make sure the hardware has stabilized. Without using interrupt threads
this delay may affect the latency of the rest of the system.
Also pass dev_name() as string for /proc/interrupts.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mark Brown [Thu, 28 Apr 2011 06:09:26 +0000 (23:09 -0700)]
Input: wm831x-ts - move BTN_TOUCH reporting to data transfer
Don't report BTN_TOUCH until we've got data as some less robust applications
can be confused by getting a touch event by itself and it doesn't seem
unreasonable for them to expect coordinates along with a touch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Mark Brown [Thu, 28 Apr 2011 06:08:34 +0000 (23:08 -0700)]
Input: wm831x-ts - fix races with IRQ management
If the WM831x pen down and data IRQs run in parallel it is possible for the
data and pen down IRQs to deadlock themselves as one is part way through
disabling its operation while the other is part way through enabling. Fix
this by always disabling the pen down interrupt while data is active and
vice versa. When a changeover is required we disable the IRQ that is to
be stopped then schedule work that will enable the new IRQ.
We need to handle the data flow in the data IRQ as the readback from the
device needs to be ordered correctly with the IRQ for robust operation.
This also fixes an issue when using the built in IRQs due to enable_irq()
not being valid from interrupt context on an interrupt controller with bus
operations like the built in IRQ controller - this issue may also have
affected other interrupt controllers. We can't rely on having the data
and pen down IRQs available via GPIOs on the CPU on every system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Jeff Brown [Wed, 27 Apr 2011 05:16:11 +0000 (22:16 -0700)]
Input: evdev - only signal polls on full packets
This patch modifies evdev so that it only becomes readable when
the buffer contains an EV_SYN/SYN_REPORT event.
On SMP systems, it is possible for an evdev client blocked on poll()
to wake up and read events from the evdev ring buffer at the same
rate as they are enqueued. This can result in high CPU usage,
particularly for MT devices, because the client ends up reading
events one at a time instead of reading complete packets.
We eliminate this problem by making the device readable only when
the buffer contains at least one complete packet. This causes
clients to block until the entire packet is available.
Signed-off-by: Jeff Brown <jeffbrown@android.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add blk_run_queue_async
block: blk_delay_queue() should use kblockd workqueue
md: fix up raid1/raid10 unplugging.
md: incorporate new plugging into raid5.
md: provide generic support for handling unplug callbacks.
md - remove old plugging code.
md/dm - remove remains of plug_fn callback.
md: use new plugging interface for RAID IO.
block: drop queue lock before calling __blk_run_queue() for kblockd punt
Revert "block: add callback function for unplug notification"
block: Enhance new plugging support to support general callbacks
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/powermac: Build fix with SMP and CPU hotplug
powerpc/perf_event: Skip updating kernel counters if register value shrinks
powerpc: Don't write protect kernel text with CONFIG_DYNAMIC_FTRACE enabled
powerpc: Fix oops if scan_dispatch_log is called too early
powerpc/pseries: Use a kmem cache for DTL buffers
powerpc/kexec: Fix regression causing compile failure on UP
powerpc/85xx: disable Suspend support if SMP enabled
powerpc/e500mc: Remove CPU_FTR_MAYBE_CAN_NAP/CPU_FTR_MAYBE_CAN_DOZE
powerpc/book3e: Fix CPU feature handling on 64-bit e5500
powerpc: Check device status before adding serial device
powerpc/85xx: Don't add disabled PCIe devices
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
Btrfs: fix free space cache leak
Btrfs: avoid taking the chunk_mutex in do_chunk_alloc
Btrfs end_bio_extent_readpage should look for locked bits
Btrfs: don't force chunk allocation in find_free_extent
Btrfs: Check validity before setting an acl
Btrfs: Fix incorrect inode nlink in btrfs_link()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_real_readdir()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_listxattr()
Btrfs: make uncache_state unconditional
btrfs: using cached extent_state in set/unlock combinations
Btrfs: avoid taking the trans_mutex in btrfs_end_transaction
Btrfs: fix subvolume mount by name problem when default mount subvolume is set
fix user annotation in ioctl.c
Btrfs: check for duplicate iov_base's when doing dio reads
btrfs: properly handle overlapping areas in memmove_extent_buffer
Btrfs: fix memory leaks in btrfs_new_inode()
Btrfs: check for duplicate iov_base's when doing dio reads
Btrfs: reuse the extent_map we found when calling btrfs_get_extent
Btrfs: do not use async submit for small DIO io's
Btrfs: don't split dio bios if we don't have to
...
next_pidmap() just quietly accepted whatever 'last' pid that was passed
in, which is not all that safe when one of the users is /proc.
Admittedly the proc code should do some sanity checking on the range
(and that will be the next commit), but that doesn't mean that the
helper functions should just do that pidmap pointer arithmetic without
checking the range of its arguments.
So clamp 'last' to PID_MAX_LIMIT. The fact that we then do "last+1"
doesn't really matter, the for-loop does check against the end of the
pidmap array properly (it's only the actual pointer arithmetic overflow
case we need to worry about, and going one bit beyond isn't going to
overflow).
[ Use PID_MAX_LIMIT rather than pid_max as per Eric Biederman ]
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com> Analyzed-by: Robert Święcki <robert@swiecki.net> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Igor Mammedov [Mon, 18 Apr 2011 17:17:17 +0000 (10:17 -0700)]
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.
If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.
Regression was introduced by hunk 5 and 6 of 5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").
Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In raid5 plugging is used for 2 things:
1/ collecting writes that require a bitmap update
2/ collecting writes in the hope that we can create full
stripes - or at least more-full.
We now release these different sets of stripes when plug_cnt
is zero.
Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
md: provide generic support for handling unplug callbacks.
When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.
If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.
This relied on the ->unplug_fn callback which doesn't exist any more.
So remove all of that code, both in md and raid5. Subsequent patches
with restore the plugging functionality.
block: drop queue lock before calling __blk_run_queue() for kblockd punt
If we know we are going to punt to kblockd, we can drop the queue
lock before calling into __blk_run_queue() since it only does a
safe bit test and a workqueue call. Since kblockd needs to grab
this very lock as one of the first things it does, it's a good
optimization to drop the lock before waking kblockd.
Revert "block: add callback function for unplug notification"
MD can't use this since it really requires us to be able to
keep more than a single piece of state for the unplug. Commit 048c9374 added the required support for MD, so get rid of this
now unused code.
Eric B Munson [Fri, 15 Apr 2011 08:12:30 +0000 (08:12 +0000)]
powerpc/perf_event: Skip updating kernel counters if register value shrinks
Because of speculative event roll back, it is possible for some event coutners
to decrease between reads on POWER7. This causes a problem with the way that
counters are updated. Delta calues are calculated in a 64 bit value and the
top 32 bits are masked. If the register value has decreased, this leaves us
with a very large positive value added to the kernel counters. This patch
protects against this by skipping the update if the delta would be negative.
This can lead to a lack of precision in the coutner values, but from my testing
the value is typcially fewer than 10 samples at a time.
Signed-off-by: Eric B Munson <emunson@mgebm.net> Cc: stable@kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stefan Roese [Thu, 14 Apr 2011 23:49:53 +0000 (23:49 +0000)]
powerpc: Don't write protect kernel text with CONFIG_DYNAMIC_FTRACE enabled
This problem was noticed on an MPC855T platform. Ftrace did oops
when trying to write to the kernel text segment.
Many thanks to Joakim for finding the root cause of this problem.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Thu, 7 Apr 2011 21:44:21 +0000 (21:44 +0000)]
powerpc: Fix oops if scan_dispatch_log is called too early
We currently enable interrupts before the dispatch log for the boot
cpu is setup. If a timer interrupt comes in early enough we oops in
scan_dispatch_log:
Unable to handle kernel paging request for data at address 0x00000010
PAPR specifies that DTL buffers can not cross AMS environments (aka CMO
in the PAPR) and can not cross a memory entitlement granule boundary
(4k). This is found in section 14.11.3.2 H_REGISTER_VPA of the PAPR.
kmalloc does not guarantee an alignment of the allocation, though,
beyond 8 bytes (at least in my understanding). Create a special kmem
cache for DTL buffers with the alignment requirement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Gortmaker [Wed, 13 Apr 2011 06:30:08 +0000 (06:30 +0000)]
powerpc/kexec: Fix regression causing compile failure on UP
Recent commit b987812b3fcaf70fdf0037589e5d2f5f2453e6ce caused
a compile failure on UP because a considerably large block
of the file was included within CONFIG_SMP, hence making a stub
function not exposed on UP builds when it needed to be.
Relocate the stub to the #else /* ! CONFIG_SMP */ section
and also annotate the relevant else/endif so that nobody
else falls into the same trap I did.
Reported-by: Michael Guntsche <mike@it-loops.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix warning 's3c_pm_show_resume_irqs' defined but not used
ARM: SAMSUNG: Fix build failure in PM CRC check code
ARM: S5P: Remove unused s3c_pm_check_resume_pin
Following commit 091738a266fc ("genirq: Remove real old transition
functions") we removed an automatic conversion of no_irq_chip to
dummy_irq_chip. This change needs to be propagated back into the alpha
backend.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new warning in gcc 4.6. Several of these variables are
used within #if 0 code, which probably ought to be removed. Most
of the changes are legitimate cleanups.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milton Miller [Thu, 14 Apr 2011 15:30:08 +0000 (10:30 -0500)]
fs: synchronize_rcu when unregister_filesystem success not failure
While checking unregister_filesystem for saftey vs extra calls for
"ext4: register ext2 and ext3 alias after ext4" I realized that
the synchronize_rcu() was called on the error path but not on
the success path.
Cc: stable (2.6.38) Signed-off-by: Milton Miller <miltonm@bga.com>
[ This probably won't really make a difference since commit d863b50ab013
("vfs: call rcu_barrier after ->kill_sb()"), but it's the right thing
to do. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Deucher [Sun, 17 Apr 2011 08:20:19 +0000 (10:20 +0200)]
i2c-algo-bit: Call pre/post_xfer for bit_test
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: make unplug timer trace event correspond to the schedule() unplug
block: let io_schedule() flush the plug inline
Merge branch 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (43 commits)
Revert "USB: isp1760-hcd: move imask clear after pending work is done"
xHCI: Implement AMD PLL quirk
xhci: Tell USB core both roothubs lost power.
usbcore: Bug fix: system can't suspend with USB3.0 device connected to USB3.0 hub
USB: Fix unplug of device with active streams
USB: xhci - also free streams when resetting devices
xhci: Fix NULL pointer deref in handle_port_status()
USB: xhci - fix math in xhci_get_endpoint_interval()
USB: xhci: simplify logic of skipping missed isoc TDs
USB: xhci - remove excessive 'inline' markings
USB: xhci: unsigned char never equals -1
USB: xhci - fix unsafe macro definitions
USB: fix formatting of SuperSpeed endpoints in /proc/bus/usb/devices
USB: isp1760-hcd: move imask clear after pending work is done
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
usb: qcserial add missing errorpath kfrees
usb: qcserial avoid pointing to freed memory
usb: Fix qcserial memory leak on rmmod
USB: ftdi_sio: add ids for Hameg HO720 and HO730
USB: option: Added support for Samsung GT-B3730/GT-B3710 LTE USB modem.
...
Merge branches 'core-fixes-for-linus', 'perf-fixes-for-linus', 'sched-fixes-for-linus', 'timer-fixes-for-linus' and 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
block: make unplug timer trace event correspond to the schedule() unplug
It's a pretty close match to what we had before - the timer triggering
would mean that nobody unplugged the plug in due time, in the new
scheme this matches very closely what the schedule() unplug now is.
It's essentially the difference between an explicit unplug (IO unplug)
or an implicit unplug (timer unplug, we scheduled with pending IO
queued).
Linus correctly observes that the most important dispatch cases
are now done from kblockd, this isn't ideal for latency reasons.
The original reason for switching dispatches out-of-line was to
avoid too deep a stack, so by _only_ letting the "accidental"
flush directly in schedule() be guarded by offload to kblockd,
we should be able to get the best of both worlds.
So add a blk_schedule_flush_plug() that offloads to kblockd,
and only use that from the schedule() path.
Josef Bacik [Tue, 12 Apr 2011 00:20:11 +0000 (20:20 -0400)]
Btrfs: avoid taking the chunk_mutex in do_chunk_alloc
Everytime we try to allocate disk space we try and see if we can pre-emptively
allocate a chunk, but in the common case we don't allocate anything, so there is
no sense in taking the chunk_mutex at all. So instead if we are allocating a
chunk, mark it in the space_info so we don't get two people trying to allocate
at the same time. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Reviewed-by: Liu Bo <liubo2009@cn.fujitsu.com>
Chris Mason [Sat, 16 Apr 2011 10:55:39 +0000 (06:55 -0400)]
Btrfs end_bio_extent_readpage should look for locked bits
A recent commit caches the extent state in end_bio_extent_readpage,
but the search it does should look for locked extents. This
fixes things to make it more effective.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: nwname should be an unsigned int
9p: Fix sparse error
fs/9p: Fix error reported by coccicheck
9p: revert tsyncfs related changes
fs/9p: Use write_inode for data sync on server
fs/9p: Fix revalidate to return correct value
Merge branch 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6879/1: fix personality test wrt usage of domain handlers
ARM: 6878/1: fix personality flag propagation across an exec
ARM: 6877/1: the ADDR_NO_RANDOMIZE personality flag should be honored with mmap()
ARM: 6876/1: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
ARM: mmp: align NR_BUILTIN_GPIO with gpio interrupt number
ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number
ARM: pxa: always clear LPM bits for PXA168 MFPR
pcmcia: limit pxa2xx_trizeps4 subdriver to trizeps4 platform
pcmcia: limit pxa2xx_balloon3 subdriver to balloon3 platform
ARM: pxafb: Fix access to nonexistent member of pxafb_info
ARM: 6872/1: arch:common:Makefile Remove unused config in the Makefile.
ARM: 6868/1: Preserve the VFP state during fork
ARM: 6867/1: Introduce THREAD_NOTIFY_COPY for copy_thread() hooks
ARM: 6866/1: Do not restrict HIGHPTE to !OUTER_CACHE
ARM: 6865/1: perf: ensure pass through zero is counted on overflow
ARM: 6864/1: hw_breakpoint: clear DBGVCR out of reset
ARM: Only allow PM_SLEEP with CPUs which support suspend
ARM: Make consolidated PM sleep code depend on PM_SLEEP
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com> Cc: <stable@kernel.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tim Chen [Fri, 15 Apr 2011 18:39:29 +0000 (11:39 -0700)]
vfs: Fix absolute RCU path walk failures due to uninitialized seq number
During RCU walk in path_lookupat and path_openat, the rcu lookup
frequently failed if looking up an absolute path, because when root
directory was looked up, seq number was not properly set in nameidata.
We dropped out of RCU walk in nameidata_drop_rcu due to mismatch in
directory entry's seq number. We reverted to slow path walk that need
to take references.
With the following patch, I saw a 50% increase in an exim mail server
benchmark throughput on a 4-socket Nehalem-EX system.
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com> Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com> Signed-off-by: Eric VAn Hensbergen <ericvh@gmail.com>
Now that we use write_inode to flush server
cache related to fid, we don't need tsyncfs either fort dotl or dotu
protocols. For dotu this helps to do a more efficient server flush.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Chris Mason [Fri, 15 Apr 2011 20:05:44 +0000 (16:05 -0400)]
Btrfs: don't force chunk allocation in find_free_extent
find_free_extent likes to allocate in contiguous clusters,
which makes writeback faster, especially on SSD storage. As
the FS fragments, these clusters become harder to find and we have
to decide between allocating a new chunk to make more clusters
or giving up on the cluster to allocate from the free space
we have.
Right now it creates too many chunks, and you can end up with
a whole FS that is mostly empty metadata chunks. This commit
changes the allocation code to be more strict and only
allocate new chunks when we've made good use of the chunks we
already have.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The divede by zero is caused by the following line,
group->cpu_power==0:
kernel/sched_fair.c::update_sg_lb_stats()
/* Adjust by relative CPU power of the group */
sgs->avg_load = (sgs->group_load * SCHED_LOAD_SCALE) / group->cpu_power;
This regression was caused by commit e23bba6044 ("x86-64, NUMA: Unify
emulated distance mapping") because it changes cpu -> node
mapping in the process of dropping fake_physnodes().
old) all cpus are assinged node 0
now) cpus are assigned round robin
(the logic is implemented by numa_init_array())
Note: The change in behavior only happens if the system doesn't
have neither ACPI SRAT table nor AMD northbridge NUMA
information.
Round robin assignment doesn't work because init_numa_sched_groups_power()
assumes all logical cpus in the same physical cpu share the same node
(then it only accounts for group_first_cpu()), and the simple round robin
breaks the above assumption.
Thus, this patch implements a reassignment of node-ids if buggy firmware
or numa emulation makes wrong cpu node map. Tt enforce all logical cpus
in the same physical cpu share the same node.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by: Tejun Heo <tj@kernel.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Brian Gerst <brgerst@gmail.com> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Shaohui Zheng <shaohui.zheng@intel.com> Cc: David Rientjes <rientjes@google.com> Cc: H. Peter Anvin <hpa@linux.intel.com> Link: http://lkml.kernel.org/r/20110415203928.1303.A69D9226@jp.fujitsu.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
projects / karo-tx-linux.git / log