Michael Chan [Wed, 3 Oct 2012 03:31:14 +0000 (20:31 -0700)]
tg3: Fix sparse warnings.
drivers/net/ethernet/broadcom/tg3.c:8121:8: warning: symbol 'i' shadows an earlier one
drivers/net/ethernet/broadcom/tg3.c:8003:6: originally declared here
drivers/net/ethernet/broadcom/tg3.c:785:5: warning: symbol 'tg3_ape_scratchpad_read' was not declared. Should it be static?
drivers/net/ethernet/broadcom/tg3.c:7781:19: warning: Using plain integer as NULL pointer
drivers/net/ethernet/broadcom/tg3.c:10231:31: error: bad constant expression
Reported-by: Fengguang Wu <fenguang.wu@intel.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
skb_reset_mac_len() relies on the value of the skb->network_header pointer,
therefore we must wait for such pointer to be recalculated before computing
the new mac_len value.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 2 Oct 2012 01:47:46 +0000 (01:47 +0000)]
bnx2x: use strlcpy() to copy a string
DRV_MODULE_VERSION is smaller than the ->version buffer so the memcpy()
copies 1 byte past the end of the string. It's not super harmful, but
it makes the static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Mon, 1 Oct 2012 23:19:14 +0000 (23:19 +0000)]
ipv6: don't add link local route when there is no link local address
When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), a route
to fe80::/64 is added in the main table:
unreachable fe80::/64 dev lo proto kernel metric 256 error -101
This route does not match any prefix (no fe80:: address on lo). In fact,
addrconf_dev_config() will not add link local address because this function
filters interfaces by type. If the link local address is added manually, the
route to the link local prefix will be automatically added by
addrconf_add_linklocal().
Note also, that this route is not deleted when the address is removed.
After looking at the code, it seems that addrconf_add_lroute() is redundant with
addrconf_add_linklocal(), because this function will add the link local route
when the link local address is configured.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
htbegin [Mon, 1 Oct 2012 16:42:43 +0000 (16:42 +0000)]
net: ethernet: davinci_cpdma: decrease the desc count when cleaning up the remaining packets
chan->count is used by rx channel. If the desc count is not updated by
the clean up loop in cpdma_chan_stop, the value written to the rxfree
register in cpdma_chan_start will be incorrect.
Signed-off-by: Tao Hou <hotforest@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 3 Oct 2012 00:26:42 +0000 (17:26 -0700)]
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Linus Torvalds [Wed, 3 Oct 2012 00:20:40 +0000 (17:20 -0700)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"First batch of InfiniBand/RDMA changes for the 3.7 merge window:
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes"
This merge also removes a new use of __cancel_delayed_work(), and
replaces it with the regular cancel_delayed_work() that is now irq-safe
thanks to the workqueue updates.
That said, I suspect the sequence in question should probably use
"mod_delayed_work()". I just did the minimal "don't use deprecated
functions" fixup, though.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
IB/qib: Fix local access validation for user MRs
mlx4_core: Disable SENSE_PORT for multifunction devices
mlx4_core: Clean up enabling of SENSE_PORT for older (ConnectX-1/-2) HCAs
mlx4_core: Stash PCI ID driver_data in mlx4_priv structure
IB/srp: Avoid having aborted requests hang
IB/srp: Fix use-after-free in srp_reset_req()
IB/qib: Add a qib driver version
RDMA/nes: Fix compilation error when nes_debug is enabled
RDMA/nes: Print hardware resource type
RDMA/nes: Fix for crash when TX checksum offload is off
RDMA/nes: Cosmetic changes
RDMA/nes: Fix for incorrect MSS when TSO is on
RDMA/nes: Fix incorrect resolving of the loopback MAC address
mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
mlx4_core: Trivial cleanups to driver log messages
mlx4_core: Trivial readability fix: "0X30" -> "0x30"
IB/mlx4: Create paravirt contexts for VFs when master IB driver initializes
mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
mlx4: Paravirtualize Node Guids for slaves
mlx4: Activate SR-IOV mode for IB
...
Linus Torvalds [Wed, 3 Oct 2012 00:16:10 +0000 (17:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A few drivers were updated with device tree bindings and others got a
few small cleanups and fixes."
Fix trivial conflict in drivers/input/keyboard/omap-keypad.c due to
changes clashing with a whitespace cleanup.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: wacom - mark Intuos5 pad as in-prox when touching buttons
Input: synaptics - adjust threshold for treating position values as negative
Input: hgpk - use %*ph to dump small buffer
Input: gpio_keys_polled - fix dt pdata->nbuttons
Input: Add KD[GS]KBDIACRUC ioctls to the compatible list
Input: omap-keypad - fixed formatting
Input: tegra - move platform data header
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: s3c2410_ts - make s3c_ts_pmops const
Input: samsung-keypad - use of_get_child_count() helper
Input: samsung-keypad - use of_match_ptr()
Input: uinput - fix formatting
Input: uinput - specify exact bit sizes on userspace APIs
Input: uinput - mark failed submission requests as free
Input: uinput - fix race that can block nonblocking read
Input: uinput - return -EINVAL when read buffer size is too small
Input: uinput - take event lock when fetching events from buffer
Input: get rid of MATCH_BIT() macro
Input: rotary-encoder - add DT bindings
Input: rotary-encoder - constify platform data pointers
...
Linus Torvalds [Tue, 2 Oct 2012 23:20:20 +0000 (16:20 -0700)]
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
Linus Torvalds [Tue, 2 Oct 2012 23:05:10 +0000 (16:05 -0700)]
Merge tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"So this is the LW GPIO patch stack for v3.7:
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by Lee
Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing."
* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
gpio: pcf857x: select IRQ_DOMAIN
gpio: Document device_node's det_debounce
gpio-lpc32xx: Add GPI_28
gpio: adnp: dt: Reference generic interrupt binding
gpio: Add Avionic Design N-bit GPIO expander support
gpio: pxa: using for_each_set_bit to simplify the code
gpio_msm: using for_each_set_bit to simplify the code
gpio: Enable the tc3298x GPIO expander driver for Device Tree
gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
gpio: pcf857x: fixup smatch WARNING
gpio: 74x164: Add support for the daisy-chaining
gpio: 74x164: dts: Add documentation for the dt binding
dt: Fix incorrect reference in gpio-led documentation
gpio: 74x164: Add device tree support
gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
gpio: 74x164: Use devm_kzalloc
gpio: 74x164: Use module_spi_driver boiler plate function
gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
...
Linus Torvalds [Tue, 2 Oct 2012 23:01:31 +0000 (16:01 -0700)]
workqueue: avoid using deprecated functions
The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.
Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Pull sparc updates from David Miller:
"Largely this is simply adding support for the Niagara 4 cpu.
Major areas are perf events (chip now supports 4 counters and can
monitor any event on each counter), crypto (opcodes are availble for
sha1, sha256, sha512, md5, crc32c, AES, DES, CAMELLIA, and Kasumi
although the last is unsupported since we lack a generic crypto layer
Kasumi implementation), and an optimized memcpy.
Finally some cleanups by Peter Senna Tschudin."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: (47 commits)
sparc64: Fix trailing whitespace in NG4 memcpy.
sparc64: Fix comment type in NG4 copy from user.
sparc64: Add SPARC-T4 optimized memcpy.
drivers/sbus/char: removes unnecessary semicolon
arch/sparc/kernel/pci_sun4v.c: removes unnecessary semicolon
sparc64: Fix function argument comment in camellia_sparc64_key_expand asm.
sparc64: Fix IV handling bug in des_sparc64_cbc_decrypt
sparc64: Add auto-loading mechanism to crypto-opcode drivers.
sparc64: Add missing pr_fmt define to crypto opcode drivers.
sparc64: Adjust crypto priorities.
sparc64: Use cpu_pgsz_mask for linear kernel mapping config.
sparc64: Probe cpu page size support more portably.
sparc64: Support 2GB and 16GB page sizes for kernel linear mappings.
sparc64: Fix bugs in unrolled 256-bit loops.
sparc64: Avoid code duplication in crypto assembler.
sparc64: Unroll CTR crypt loops in AES driver.
sparc64: Unroll ECB decryption loops in AES driver.
sparc64: Unroll ECB encryption loops in AES driver.
sparc64: Add ctr mode support to AES driver.
sparc64: Move AES driver over to a methods based implementation.
...
Haiyang Zhang [Tue, 2 Oct 2012 05:30:24 +0000 (05:30 +0000)]
hyperv: Add buffer for extended info after the RNDIS response message.
In some response messages, there may be some extended info after the
message.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:23 +0000 (05:30 +0000)]
hyperv: Report actual status in receive completion packet
The existing code always reports NVSP_STAT_SUCCESS. This patch adds the
mechanism to report failure when it happens.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:22 +0000 (05:30 +0000)]
hyperv: Remove extra allocated space for recv_pkt_list elements
The receive code path doesn't use the page buffer, so remove the
extra allocated space here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:21 +0000 (05:30 +0000)]
hyperv: Fix page buffer handling in rndis_filter_send_request()
To prevent possible data corruption in RNDIS requests, add another
page buffer if the request message crossed page boundary.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:20 +0000 (05:30 +0000)]
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
Return ETIMEDOUT when the reply message is not received in time.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:19 +0000 (05:30 +0000)]
hyperv: Fix the max_xfer_size in RNDIS initialization
According to RNDIS specs, Windows sets this size to
0x4000. I use the same value here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Move vxlan UDP socket to correct network namespace
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 2 Oct 2012 18:11:09 +0000 (11:11 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Linus Torvalds [Tue, 2 Oct 2012 17:52:28 +0000 (10:52 -0700)]
Merge branch 'for-3.7-hierarchy' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup hierarchy update from Tejun Heo:
"Currently, different cgroup subsystems handle nested cgroups
completely differently. There's no consistency among subsystems and
the behaviors often are outright broken.
People at least seem to agree that the broken hierarhcy behaviors need
to be weeded out if any progress is gonna be made on this front and
that the fallouts from deprecating the broken behaviors should be
acceptable especially given that the current behaviors don't make much
sense when nested.
This patch makes cgroup emit warning messages if cgroups for
subsystems with broken hierarchy behavior are nested to prepare for
fixing them in the future. This was put in a separate branch because
more related changes were expected (didn't make it this round) and the
memory cgroup wanted to pull in this and make changes on top."
* 'for-3.7-hierarchy' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: mark subsystems with broken hierarchy support and whine if cgroups are nested for them
Linus Torvalds [Tue, 2 Oct 2012 17:50:47 +0000 (10:50 -0700)]
Merge branch 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- xattr support added. The implementation is shared with tmpfs. The
usage is restricted and intended to be used to manage per-cgroup
metadata by system software. tmpfs changes are routed through this
branch with Hugh's permission.
- cgroup subsystem ID handling simplified.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Define CGROUP_SUBSYS_COUNT according the configuration
cgroup: Assign subsystem IDs during compile time
cgroup: Do not depend on a given order when populating the subsys array
cgroup: Wrap subsystem selection macro
cgroup: Remove CGROUP_BUILTIN_SUBSYS_COUNT
cgroup: net_prio: Do not define task_netpioidx() when not selected
cgroup: net_cls: Do not define task_cls_classid() when not selected
cgroup: net_cls: Move sock_update_classid() declaration to cls_cgroup.h
cgroup: trivial fixes for Documentation/cgroups/cgroups.txt
xattr: mark variable as uninitialized to make both gcc and smatch happy
fs: add missing documentation to simple_xattr functions
cgroup: add documentation on extended attributes usage
cgroup: rename subsys_bits to subsys_mask
cgroup: add xattr support
cgroup: revise how we re-populate root directory
xattr: extract simple_xattr code from tmpfs
Linus Torvalds [Tue, 2 Oct 2012 16:54:49 +0000 (09:54 -0700)]
Merge branch 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This fixes a local merge conflict resolution done wrong locally in
arm-soc for-next. soc.h was added on a cleanup branch, but the driver
was moved and the header no longer needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
[ .. and I did the same wrong merge, since git automatically does the
whole rename detection etc, so applying this patch from Olof - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 2 Oct 2012 02:11:38 +0000 (19:11 -0700)]
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Linus Torvalds [Tue, 2 Oct 2012 01:56:31 +0000 (18:56 -0700)]
Merge tag 'docs' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc documentation updates from Olof Johansson:
"Documentation update for Marvell SoCs, the secret decoder ring to all
their crazy product names and numbers."
* tag 'docs' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: add documentation describing Marvell families of SoC
Linus Torvalds [Tue, 2 Oct 2012 01:55:15 +0000 (18:55 -0700)]
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates, take 2 from Olof Johansson:
"This branch contains mostly a set of changes for device tree bindings
on Samsung Exynos. It was staged behind the other branches due to
dependencies on pincontrol and board changes."
Fix up trivial conflict in drivers/clocksource/Makefile due to earlier
conflict resolution.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Add nodes for dw_mmc controllers for Samsung EXYNOS5250 platforms
ARM: EXYNOS: Add AUXDATA support for MSHC controllers
ARM: EXYNOS: Add support for MSHC controller clocks
ARM: dts: Enable on-board keys as wakeup source for exynos4210-origen
ARM: dts: use uart2 for console on smdkv310 and smdk5250
ARM: dts: Add basic dts file for Samsung Trats board
ARM: EXYNOS: Add OF compatibility lookups for EXYNOS4 i2c adapters
ARM: dts: Specify address and size cells for i2c controllers for EXYNOS4
ARM: dts: Assume status of all optional nodes as disabled for exynos4
ARM: EXYNOS: Use exynos4 prefix instead of exynos4210 on exynos4-dt
ARM: dts: Move parts common to EXYNOS4 from exynos4210.dtsi to exynos4.dtsi
Linus Torvalds [Tue, 2 Oct 2012 01:48:30 +0000 (18:48 -0700)]
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc board specific updates from Olof Johansson:
"Misc board updates:
- Greg added a handful of boards to KS8695 (since he has stepped up
to maintain it).
- Qualcomm has added DT-only board support for a couple of their
newer SoCs.
- misc other updates for Samsung and Freescale boards."
Fix up trivial conflict in arch/arm/mach-shmobile/board-armadillo800eva.c
due to gpio device data being added next to hdmi device data that got moved.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: msm: Allow 8960 and 8660 to compile together
ARM: msm: Allow msm_iomap-8x60 and msm_iomap-8960 to coexist
ARM: EXYNOS: Add generic PWM lookup support for SMDKV310
ARM: EXYNOS: Add generic PWM lookup support for SMDK4X12
ARM: EXYNOS: Use generic pwm driver in Origen board
ARM: shmobile: armadillo800eva: Add support RTC
ARM: ks8695: add board support for the OpenGear boards based on the KS8695
ARM: ks8695: add board support for the SnapGear boards based on the KS8695
ARM: dts: Add heartbeat gpio-leds support to Origen
ARM: dts: Use active low flag for gpio-keys on Origen
ARM: shmobile: marzen: enable thermal sensor
ARM: shmobile: marzen: fixup regulator id for smsc911x
ARM: shmobile: marzen: add SDHI0 support
ARM: mmp: enable debug uart port in defconfig
ARM: mmp: implement DEBUG_LL port choice
ARM: S3C64XX: Register audio platform devices for Bells on Cragganmore
ARM: S3C64XX: Update configuration for WM5102 module on Cragganmore
ARM: mx27pdk: Add audio support
ARM: ttc_dkb: add nand support
Linus Torvalds [Tue, 2 Oct 2012 01:46:13 +0000 (18:46 -0700)]
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Linus Torvalds [Tue, 2 Oct 2012 01:35:58 +0000 (18:35 -0700)]
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates, take 2 from Olof Johansson:
"This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: remove mach/irqs.h
ARM: mxs: select SPARSE_IRQ
ARM: mxs: adopt irq_domain support for icoll driver
ARM: mxs: select MULTI_IRQ_HANDLER
ARM: mxs: retrieve timer irq from device tree
gpio/mxs: adopt irq_domain support for mxs gpio driver
David S. Miller [Tue, 2 Oct 2012 01:32:55 +0000 (21:32 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
Some bug fixes that should go into 3.7:
1. Fix oops when removing device with SR-IOV enabled. (This regression
was introduced by the last set of changes, so the fix does not need to
be applied to any earlier kernel versions.)
2. Fix firmware structure field lookup bug that resulted in missing
sensor information.
3. Fix bug that makes self-test do very little in some configurations.
4. Fix the numbering of ethtool RX flow steering filters to reflect the
real hardware priorities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 2 Oct 2012 01:32:45 +0000 (18:32 -0700)]
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc cleanups, part 2 from Olof Johansson:
"A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed.
It's an SoC that's used on some stationary VoIP platforms, and is in
desperate need of some cleanup. Broadcom came back and suggested that
we just deprecate the platform for now, since they aren't going to
spend the resources needed on cleaning it up, and there are no users
of the platform directly from mainline."
Fix some conflicts due to BCM2835 getting added next to the removed
BCMRING, and removal of tegra files that had been converted to
devicetree.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
ARM: Remove mach-bcmring
ARM: clps711x: Remove board support for CEIVA
ARM: clps711x: Fix register definitions
ARM: clps711x: Fix lowlevel debug-macro
ARM: clps711x: Added simple clock framework
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
Linus Torvalds [Tue, 2 Oct 2012 01:28:06 +0000 (18:28 -0700)]
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
Linus Torvalds [Tue, 2 Oct 2012 01:24:44 +0000 (18:24 -0700)]
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates from Olof Johansson:
"Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen Warren.
It's still early days on mainline support, with just the basics
working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well."
Fix up trivial conflicts with the clk infrastructure changes.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (62 commits)
ARM: shmobile: add new __iomem annotation for new code
ARM: LPC32xx: Support GPI 28
ARM: LPC32xx: Platform update for devicetree completion of spi-pl022
ARM: LPC32xx: Board cleanup
irqchip: fill in empty Kconfig
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
...
Linus Torvalds [Tue, 2 Oct 2012 01:21:07 +0000 (18:21 -0700)]
Merge tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc MAINTAINERS updates from Olof Johansson:
"Maintainers updates for KS8965 adding Greg Ungerer, and removing
myself and Colin Cross as tegra maintainers, since Stephen Warren has
been handling it on his own for several releases now."
* tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ks8695: add maintainers entry
MAINTAINERS: tegra: remove Olof/Colin, add device tree files
MAINTAINERS: add defconfig file to TEGRA section
Linus Torvalds [Tue, 2 Oct 2012 01:19:05 +0000 (18:19 -0700)]
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Linus Torvalds [Tue, 2 Oct 2012 01:02:07 +0000 (18:02 -0700)]
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM soc bug fixes from Olof Johansson:
"These were submitted as bug fixes before v3.6 but not considered
important enough to be included in it. Some of them cross over to
cleanup territory as well, and aren't strictly bugfixes."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: nomadik: remove NAND_NO_READRDY use
ARM: pxa: fix return value check in pxa2xx_drv_pcmcia_probe()
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
ARM: ep93xx: Move ts72xx.h out of include/mach
ARM: ep93xx: use __iomem pointers for MMIO
ARM: msm: Fix early debug uart mapping on some memory configs
ARM: msm: io: Change the default static iomappings to be shared
ARM: msm: io: Remove 7x30 iomap region from 7x00
ARM: msm: Remove call to missing FPGA init on 8660
ARM: OMAP4: wakeupgen: remove duplicate AUXCOREBOOT* read/write
ARM: OMAP4: wakeupgen: Fix the typo in AUXCOREBOOT register save
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
...
Ben Hutchings [Fri, 24 Aug 2012 19:12:20 +0000 (20:12 +0100)]
sfc: Fix the reported priorities of different filter types
Each RX filter table contains filters with two different levels of
specificity: TCP/IPv4 and UDP/IPv4 filters match the local address and
port and optionally the remote address and port; Ethernet filters
match the local address and optionally the VID. The more specific
filters always override less specific filters within the same table,
and should be numbered accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 11 Sep 2012 20:46:41 +0000 (21:46 +0100)]
sfc: Fix MCDI structure field lookup
The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword. In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 2 Oct 2012 00:43:45 +0000 (01:43 +0100)]
sfc: Fix null function pointer in efx_sriov_channel_type
Commit c31e5f9 ('sfc: Add channel specific receive_skb handler and
post_remove callback') added the function pointer field
efx_channel_type::post_remove and an unconditional call through it.
This field should have been initialised to efx_channel_dummy_op_void
in the existing instances of efx_channel_type, but this was only done
in efx_default_channel_type. Consequently, if a device has SR-IOV
enabled then removing the driver or device will result in an oops.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This is an implementation of Virtual eXtensible Local Area Network
as described in draft RFC:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
The driver integrates a Virtual Tunnel Endpoint (VTEP) functionality
that learns MAC to IP address mapping.
This implementation has not been tested only against the Linux
userspace implementation using TAP, not against other vendor's
equipment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 1 Oct 2012 22:27:35 +0000 (15:27 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS updates from Steve French:
"This patchset is the final section of the SMB2.1 support merge for
cifs.ko. It also includes improvements to the cifs socket handling
from Jeff, and also fixes a few cifs bug fixes. It adds SMB2 support
for file and inode operations as well as moves some existing cifs code
to use ops server struct of protocol specific callbacks.
Most of this code is SMB2 specific. When enabled SMB2.1 does pass
various functional tests including most of the connectathon test
suite, For SMB2.1, Connectathon test 4 and some related tests fail due
to not updating mode bits remotely (cifsacl support where mode bits
are approximated with the cifs acl is not enable for smb2), and test8
(symlink) support is not completed for SMB2 yet (note that we will
likely have a "Unix Extensions" eventually, at least for Samba, so in
the long run posix locks won't have to be emulated when mounting Linux
to Linux, but for most NAS and for Windows mounts posix lock emulation
will still used for SMB2 in a similar fashion as we do for cifs).
SMB2.1 dialect is supported. Although additional fixes to enable smb2
(the original smb2.02) dialect and to add various optional features of
the smb3 dialect are expected to be added in the future as testing
progresses, currently mounting with the "vers=2.1" is supported (in
order to mount using SMB2.1 to servers like Samba 4, and Windows 7,
Windows 2008R2)."
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6: (82 commits)
[CIFS] Fix indentation of fs/cifs/Kconfig entries
[CIFS] Fix SMB2 negotiation support to select only one dialect (based on vers=)
cifs: obtain file access during backup intent lookup (resend)
CIFS: Fix possible freed pointer dereference in CIFS_SessSetup
CIFS: Fix possible freed pointer dereference in SMB2_sess_setup
CIFS: Make ops->close return void
cifs: change DOS/NT/POSIX mapping of ERRnoresource
cifs: remove support for deprecated "forcedirectio" and "strictcache" mount options
cifs: remove support for CIFS_IOC_CHECKUMOUNT ioctl
CIFS: Fix possible memory leaks in SMB2 code
CIFS: Fix endian conversion of IndexNumber
Trivial endian fixes
MARK SMB2 support EXPERIMENTAL
Update cifs version number
cifs: add FL_CLOSE to fl_flags mask in cifs_read_flock
cifs: Mangle string used for unc in /proc/mounts
cifs: cleanups for cifs_mkdir_qinfo
CIFS: Fix fast lease break after open problem
CIFS: Add SMB2.1 lease break support
CIFS: Fix cache coherency for read oplock case
...
Linus Torvalds [Mon, 1 Oct 2012 22:21:43 +0000 (15:21 -0700)]
Get rid of Documentation/feature-removal.txt
This file has turned out to be a pure write-only file that causes merge
conflicts and has no actual redeeming features.
There is never any reason to add stuff to this idiotic file. Either
something isn't getting used, and you should just remove it, or there is
no excuse for removing it in the first place. Just stop the idiocy.
It has also been the excuse for just plain bad behavior ("Hey, I don't
like xyz, so let's mark it for removal" followed by "Hey, look, it been
in feature-removal.txt for six months now, so we should remove it").
The recent bogus setitimer() ABI change request was just the most recent
example of pointless and incorrect mental masturbation involving this
file, and I'm tired of the silly and pointless conflicts in the file.
This removal was discussed during the recent kernel summit, and while
Steven Rostedt suggested we should just enter the file itself in the
feature-removal schedule (to see if anybody who edits the file actually
looks at it), that's cute but non-productive.
Paul Gortmaker [Mon, 1 Oct 2012 15:43:49 +0000 (11:43 -0400)]
tg3: unconditionally select HWMON support when tg3 is enabled.
There is the seldom used corner case where HWMON=m at the same
time as TIGON3=y (typically randconfigs) which will cause a link
fail like:
drivers/built-in.o: In function `tg3_close':
tg3.c:(.text+0x16bd86): undefined reference to `hwmon_device_unregister'
drivers/built-in.o: In function `tg3_hwmon_open':
tg3.c:(.text+0x16fc4b): undefined reference to `hwmon_device_register'
make[1]: *** [vmlinux] Error 1
Fix it as suggested by DaveM[1] by having the Kconfig logic simply
select HWMON when TIGON3 is selected. This gets rid of all the
extra IS_ENABLED ifdeffery in tg3.c as a side benefit.
Cc: Michael Chan <mchan@broadcom.com> Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reported-by: Anisse Astier <anisse@astier.eu> Suggested-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't meant to be applied, commit 342b7b741d76bc8aadeff844634348bb2a343d19 ("net: ti cpsw ethernet: set
IFCTL_A bit in MACCONTROL") was redone in such a way to make this
commit unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
flexcan: disable bus error interrupts for the i.MX28
Due to a bug in most Flexcan cores, the bus error interrupt needs
to be enabled. Otherwise we don't get any error warning or passive
interrupts. This is _not_ necessary for the i.MX28 and this patch
disables bus error interrupts if "berr-reporting" is not requested.
This avoids bus error flooding, which might harm, especially on
low-end systems.
To handle such quirks of the Flexcan cores, a hardware feature flag
has been introduced, also replacing the "hw_ver" variable. So far
nobody could tell what Flexcan core version is available on what
Freescale SOC, apart from the i.MX6Q and P1010, and which bugs or
features are present on the various "hw_rev".
CC: Hui Wang <jason77.wang@gmail.com> CC: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 27 Sep 2012 12:06:02 +0000 (12:06 +0000)]
IB/ipoib: Add more rtnl_link_ops callbacks
Add the rtnl_link_ops changelink and fill_info callbacks, through
which the admin can now set/get the driver mode, etc policies.
Maintain the proprietary sysfs entries only for legacy childs.
For child devices, set dev->iflink to point to the parent
device ifindex, such that user space tools can now correctly
show the uplink relation as done for vlan, macvlan, etc
devices. Pointed out by Patrick McHardy <kaber@trash.net>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Wed, 26 Sep 2012 07:24:27 +0000 (07:24 +0000)]
net: ti cpsw ethernet: allow reading phy interface mode from DT
Allow users to specify the phy interface of the CPSW slaves. The new
node parameter is called "phy_if_mode" and is optional. The original
behaviour of the driver is preserved when not given.
Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack [Thu, 27 Sep 2012 09:19:34 +0000 (09:19 +0000)]
net: ti cpsw ethernet: set IFCTL_A bit in MACCONTROL
For RMII/RGMII mode operation in 100Mbps, the CPSW needs to set the
IFCTL_A bits in the MACCONTROL register. For all other PHY modes, this
bit is unused, so setting it unconditionally shouldn't cause any
trouble.
Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 28 Sep 2012 07:53:26 +0000 (07:53 +0000)]
mlx4: dont orphan skbs in mlx4_en_xmit()
After commit e22979d96a55d (mlx4_en: Moving to Interrupts for TX
completions) we no longer need to orphan skbs in mlx4_en_xmit()
since skb wont stay a long time in TX ring before their release.
Orphaning skbs in ndo_start_xmit() should be avoided as much as
possible, since it breaks TCP Small Queue or other flow control
mechanisms (per socket limits)
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yevgeny Petrilin <yevgenyp@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 27 Sep 2012 19:29:05 +0000 (19:29 +0000)]
net: add gro_cells infrastructure
This adds a new include file (include/net/gro_cells.h), to bring GRO
(Generic Receive Offload) capability to tunnels, in a modular way.
Because tunnels receive path is lockless, and GRO adds a serialization
using a napi_struct, I chose to add an array of up to
DEFAULT_MAX_NUM_RSS_QUEUES cells, so that multi queue devices wont be
slowed down because of GRO layer.
skb_get_rx_queue() is used as selector.
In the future, we might add optional fanout capabilities, using rxhash
for example.
With help from Ben Hutchings who reminded me
netif_get_num_default_rss_queues() function.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 1 Oct 2012 20:59:17 +0000 (13:59 -0700)]
Merge branch 'x86-smap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/smap support from Ingo Molnar:
"This adds support for the SMAP (Supervisor Mode Access Prevention) CPU
feature on Intel CPUs: a hardware feature that prevents unintended
user-space data access from kernel privileged code.
It's turned on automatically when possible.
This, in combination with SMEP, makes it even harder to exploit kernel
bugs such as NULL pointer dereferences."
Fix up trivial conflict in arch/x86/kernel/entry_64.S due to newly added
includes right next to each other.
* 'x86-smap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, smep, smap: Make the switching functions one-way
x86, suspend: On wakeup always initialize cr4 and EFER
x86-32: Start out eflags and cr4 clean
x86, smap: Do not abuse the [f][x]rstor_checking() functions for user space
x86-32, smap: Add STAC/CLAC instructions to 32-bit kernel entry
x86, smap: Reduce the SMAP overhead for signal handling
x86, smap: A page fault due to SMAP is an oops
x86, smap: Turn on Supervisor Mode Access Prevention
x86, smap: Add STAC and CLAC instructions to control user space access
x86, uaccess: Merge prototypes for clear_user/__clear_user
x86, smap: Add a header file with macros for STAC/CLAC
x86, alternative: Add header guards to <asm/alternative-asm.h>
x86, alternative: Use .pushsection/.popsection
x86, smap: Add CR4 bit for SMAP
x86-32, mm: The WP test should be done on a kernel page
Linus Torvalds [Mon, 1 Oct 2012 20:56:35 +0000 (13:56 -0700)]
Merge tag 'please-pull-ia64-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"Usual mish-mash of ia64 fixes for next merge window"
* tag 'please-pull-ia64-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] xen: Fix return value check in xencomm_vtop()
[IA64] Must enable interrupts in do_notify_resume_user before calling tracehook_notify_resume()
[IA64] kexec: Move the dereference below the NULL test
[IA64] Fix a node distance bug
Linus Torvalds [Mon, 1 Oct 2012 20:55:51 +0000 (13:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"All pretty boring, seems like all of us had better things to do last
summer..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use PTR_RET rather than if(IS_ERR(...)) + PTR_ERR
m68k/q40: Use PTR_RET rather than if(IS_ERR(...)) + PTR_ERR
m68k/amiga: Use PTR_RET rather than if(IS_ERR(...)) + PTR_ERR
m68k/apollo: Remove disabled definitions in apollohw.h
Linus Torvalds [Mon, 1 Oct 2012 20:51:58 +0000 (13:51 -0700)]
Merge tag 'dlm-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"There are two main patches in this set, both related to the userland
dlm_controld daemon.
The first fixes a deadlock between dlm_controld and the dlm_send
workqueue when both access configfs data simultaneously.
The second reworks some code to get around a long standing, but
intentional, unlock balance warning. The userland daemon no longer
takes a lock that is later released from the kernel.
The other commits are minor fixes and changes."
* tag 'dlm-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: check the maximum size of a request from user
dlm: cleanup send_to_sock routine
dlm: convert add_sock routine return value type to void
dlm: remove redundant variable assignments
dlm: fix unlock balance warnings
dlm: fix uninitialized spinlock
dlm: fix deadlock between dlm_send and dlm_controld
Nicolas Dichtel [Wed, 26 Sep 2012 00:04:55 +0000 (00:04 +0000)]
ipv6: del unreachable route when an addr is deleted on lo
When an address is added on loopback (ip -6 a a 2002::1/128 dev lo), two routes
are added:
- one in the local table:
local 2002::1 via :: dev lo proto none metric 0
- one the in main table (for the prefix):
unreachable 2002::1 dev lo proto kernel metric 256 error -101
When the address is deleted, the route inserted in the main table remains
because we use rt6_lookup(), which returns NULL when dst->error is set, which
is the case here! Thus, it is better to use ip6_route_lookup() to avoid this
kind of filter.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 1 Oct 2012 03:46:19 +0000 (03:46 +0000)]
bnx2x,cnic: use FW 7.8.2
This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.
A short summary of minor bugs fixed by this FW:
1. In switch dependent mode, fix several issues regarding inner vlan
vs. DCB priorities.
2. iSCSI - not all packets were completed on a forward channel.
3. DCB - fixed for 4-port devices.
4. Fixed false parity reported in CAM memories when operating near -5%
on the 1.0V core supply.
5. ETS default settings are set to fairness between traffic classes
(rather than strict priority), and uses the same chip receive buffer
configuration for both PFC and pause.
For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Mon, 1 Oct 2012 01:56:55 +0000 (01:56 +0000)]
be2net: fix vfs enumeration
Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.
This 2nd version uses pci_physfn instead of checking dev->physfn directly.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weiping Pan [Fri, 28 Sep 2012 20:15:30 +0000 (20:15 +0000)]
use skb_end_offset() in skb_try_coalesce()
Commit ec47ea824774(skb: Add inline helper for getting the skb end offset from
head) introduces this helper function, skb_end_offset(),
we should make use of it.
Signed-off-by: Weiping Pan <wpan@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 1 Oct 2012 20:23:01 +0000 (13:23 -0700)]
Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB changes from Greg Kroah-Hartman:
"Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree.
There are also the usual XHCI set of updates, and other various driver
changes and updates. We also are trying hard to remove the old dbg()
macro, but the final bits of that removal will be coming in through
the networking tree before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.
* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
USB: uas: fix gcc warning
USB: uas: fix locking
USB: Fix race condition when removing host controllers
USB: uas: add locking
USB: uas: fix abort
USB: uas: remove aborted field, replace with status bit.
USB: uas: fix task management
USB: uas: keep track of command urbs
xhci: Intel Panther Point BEI quirk.
powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
Revert "usb : Add sysfs files to control port power."
USB: serial: remove vizzini driver
usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
Increase XHCI suspend timeout to 16ms
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
USB: sierra_ms: don't keep unused variable
fsl/usb: Add support for USB controller version 2.4
USB: qcaux: add Pantech vendor class match
...
Linus Torvalds [Mon, 1 Oct 2012 19:26:52 +0000 (12:26 -0700)]
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Linus Torvalds [Mon, 1 Oct 2012 19:11:39 +0000 (12:11 -0700)]
Merge tag 'staging-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg Kroah-Hartman:
"Here is the big staging tree update for the 3.7-rc1 merge window.
There are a few patches in here that are outside of the staging area,
namely HID and IIO patches, but all of them have been acked by the
relevant subsystem maintainers. The IIO stuff is still coming in
through this tree as it hasn't entirely moved out of the staging tree,
but is almost there.
Other than that, there wa a ton of work on the comedi drivers to make
them more readable and the correct style. Doing that removed a lot of
code, but we added a new driver to the staging tree, so we didn't end
up with a net reduction this time around:
Linus Torvalds [Mon, 1 Oct 2012 19:10:44 +0000 (12:10 -0700)]
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
Linus Torvalds [Mon, 1 Oct 2012 19:09:59 +0000 (12:09 -0700)]
Merge tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver merge from Greg Kroah-Hartman:
"Here is the "big" char/misc driver tree update for the 3.7-rc1 merge
window.
Nothing major, just a number of driver updates and fixes, all of which
have been in the linux-next releases for a while now either in my
tree, or in Andrew's (the lis3l driver changes came from his tree last
week).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (52 commits)
drivers/misc/lis3lv02d/lis3lv02d_i2c.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add lis3lv02d device tree init
drivers/misc/lis3lv02d: remove lis3lv02d driver DT init
drivers/misc/lis3lv02d/lis3lv02d_spi.c: add DT matching table passthru code
drivers/misc/lis3lv02d: add generic DT matching code
lis3lv02d: fix some comments specific to lis331dlh driver
MISC: hpilo, remove pci_disable_device
pcmcia: synclink_cs: fix potential tty NULL dereference
drivers/char/mmtimer.c: Remove useless kfree
drivers/char: removes unnecessary semicolon
char/misc: remove CONFIG_EXPERIMENTAL dependencies
mei: don't print buffer as a string
mei: struct mei_message_data doesn't have to be packed
mei: add error messages for open count errors
misc: use module_spi_driver
tifm: use module_pci_driver
misc/at25, dt: Improve at25 SPI eeprom device tree bindings.
mei: add lynx point pci device ids
mei: fix max number of open handles
mei: rename struct pci_dev *mei_device to mei_pdev
...
Linus Torvalds [Mon, 1 Oct 2012 19:09:04 +0000 (12:09 -0700)]
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk framework update from Michael Turquette:
"The common clk framework changes for 3.7 are dominated by ARM platform
ports to the framework along with one MIPS port, one MFD port, one
minor framework enhancement and one helper function for platforms
expressing their clock data through device tree."
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: add of_clk_src_onecell_get() support
clk: ux500: Define smp_twd clock for u8500
mfd: dbx500: Provide a more accurate smp_twd clock
clk: ux500: Support for prmcu_rate clock
clk: Provide option for clk_get_rate to issue hw for new rate
clock: max77686: Add driver for Maxim 77686 32Khz crystal oscillator.
ARM: ux500: Switch to use common clock framework
clk: ux500: Clock definitions for u8500
clk: ux500: First version of clock definitions for ux500
clk: ux500: Adapt PRCMU and PRCC clocks for common clk
clk: versatile: make config option boolean
clk: add Loongson1B clock support
arm: mmp: make all SOCs use common clock by default
clk: mmp: add clock definition for mmp2
clk: mmp: add clock definition for pxa910
clk: mmp: add clock definition for pxa168
clk: mmp: add mmp specific clocks
clk: convert ARM RealView to common clk
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
Linus Torvalds [Mon, 1 Oct 2012 19:05:36 +0000 (12:05 -0700)]
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Linus Torvalds [Mon, 1 Oct 2012 18:51:57 +0000 (11:51 -0700)]
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 support from Catalin Marinas:
"Linux support for the 64-bit ARM architecture (AArch64)
Features currently supported:
- 39-bit address space for user and kernel (each)
- 4KB and 64KB page configurations
- Compat (32-bit) user applications (ARMv7, EABI only)
- Flattened Device Tree (mandated for all AArch64 platforms)
- ARM generic timers"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (35 commits)
arm64: ptrace: remove obsolete ptrace request numbers from user headers
arm64: Do not set the SMP/nAMP processor bit
arm64: MAINTAINERS update
arm64: Build infrastructure
arm64: Miscellaneous header files
arm64: Generic timers support
arm64: Loadable modules
arm64: Miscellaneous library functions
arm64: Performance counters support
arm64: Add support for /proc/sys/debug/exception-trace
arm64: Debugging support
arm64: Floating point and SIMD
arm64: 32-bit (compat) applications support
arm64: User access library functions
arm64: Signal handling support
arm64: VDSO support
arm64: System calls handling
arm64: ELF definitions
arm64: SMP support
arm64: DMA mapping API
...
Linus Torvalds [Mon, 1 Oct 2012 18:49:56 +0000 (11:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
"The main new feature is machine support for System zEC12 including
transactional memory, runtime instrumentation, support for scm block
devices via eadm subchannels, and support for CEX4 crypto cards.
In addition there are some nice improvements: bpf jit compiler, arch
backend for cmpxchg_double, relative exception table entries, dasd
partition detection independent from the dasd driver ioctls, and cpu
cache information in /proc/cpuinfo and /sys/device/cpu.
And last but not least a series of cleanup patches from Heiko."
Fix up trivial add-add conflict in arch/s390/Kconfig due to commit b952741c8079 ("cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING")
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (76 commits)
s390: update defconfig
s390/jump label,nss: let shared kernel support depend on !JUMP_LABEL
s390/disassembler: fix decoding of risblg instruction
s390/bpf,jit: add support for BPF_S_ANC_ALU_XOR_X instruction
s390/traps: move call to print_modules() out of show_regs()
s390/mm: mark free_initrd_mem() as __init
s390/dasd: check count address during online setting
drivers/s390/char/monreader.c: fix error return code
s390/cmpxchg,percpu: implement cmpxchg_double()
s390/percpu: implement this_cpu_add_return()
s390/percpu: implement this_cpu_xchg()
s390/kexec: remove CONFIG_KEXEC
s390/irq: use designated initializers for irq class array
s390: add uninitialized_var() to suppress false positive compiler warnings
s390/crashdump: move fill_cpu_elf_notes() prototype to header file
s390/process: add missing header include
s390/ptrace: add missing ifdef
s390/ipl,decrompressor: disable branch profiling
s390/perf_events: compile only for CONFIG_64BIT
s390/tape: remove even more tape block leftovers
...
Linus Torvalds [Mon, 1 Oct 2012 18:15:17 +0000 (11:15 -0700)]
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/microcode changes from Ingo Molnar:
"The biggest changes are to AMD microcode patching: add code for
caching all microcode patches which belong to the current family on
which we're running, in the kernel.
We look up the patch needed for each core from the cache at
patch-application time instead of holding a single patch per-system"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Fix use after free in free_cache()
x86, microcode, AMD: Rewrite patch application procedure
x86, microcode, AMD: Add a small, per-family patches cache
x86, microcode, AMD: Add reverse equiv table search
x86, microcode: Add a refresh firmware flag to ->request_microcode_fw
x86, microcode, AMD: Read CPUID(1).EAX on the correct cpu
x86, microcode, AMD: Check before applying a patch
x86, microcode, AMD: Remove useless get_ucode_data wrapper
x86, microcode: Straighten out Kconfig text
x86, microcode: Cleanup cpu hotplug notifier callback
x86, microcode: Drop uci->mc check on resume path
x86, microcode: Save an indentation level in reload_for_cpu
Linus Torvalds [Mon, 1 Oct 2012 18:14:17 +0000 (11:14 -0700)]
Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/platform changes from Ingo Molnar:
"This cleans up some Xen-induced pagetable init code uglies, by
generalizing new platform callbacks and state: x86_init.paging.*"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
Linus Torvalds [Mon, 1 Oct 2012 18:13:33 +0000 (11:13 -0700)]
Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/mm changes from Ingo Molnar:
"The biggest change is new TLB partial flushing code for AMD CPUs.
(The v3.6 kernel had the Intel CPU side code, see commits e0ba94f14f74..effee4b9b3b.)
There's also various other refinements around the TLB flush code"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Distinguish TLB shootdown interrupts from other functions call interrupts
x86/mm: Fix range check in tlbflush debugfs interface
x86, cpu: Preset default tlb_flushall_shift on AMD
x86, cpu: Add AMD TLB size detection
x86, cpu: Push TLB detection CPUID check down
x86, cpu: Fixup tlb_flushall_shift formatting
Linus Torvalds [Mon, 1 Oct 2012 18:12:13 +0000 (11:12 -0700)]
Merge branch 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/MCE update from Ingo Molnar:
"Various MCE robustness enhancements.
One of the changes adds CMCI (Corrected Machine Check Interrupt) poll
mode on Intel Nehalem+ CPUs, which mode is automatically entered when
the rate of messages is too high - and exited once the storm is over.
projects / karo-tx-linux.git / log