Jon Cooper [Mon, 30 Sep 2013 16:36:50 +0000 (17:36 +0100)]
sfc: Correct RX dropped count for drops while interface is down
We don't directly control RX ingress on Siena or any later
controllers, and so we cannot prevent packets from entering the RX
datapath while the RX queues are not set up. This results in
the hardware incrementing RX_NODESC_DROP_CNT, but it's not an
error and we should not include it in error stats.
When bringing an interface up or down, pull (or wait for) stats and
count the number of packets that were dropped while the interface was
down. Subtract this from the reported RX dropped count.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 24 Sep 2013 22:21:57 +0000 (23:21 +0100)]
sfc: Tighten the check for RX merged completion events
The addition of RX event merging support means we don't reliably
detect dropped RX events now. Currently we will only detect them if
the previous event for the RX queue had the CONT bit set.
Only accept RX completion events as merged if the
GET_CAPABILITIES_OUT_RX_BATCHING bit is set in datapath_caps (which it
won't be for the low-latency datapath) and the CONT bit is not set on
the event.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Jon Cooper [Mon, 16 Sep 2013 13:18:51 +0000 (14:18 +0100)]
sfc: Add MC BISTs to ethtool offline self test on EF10
To run BISTs the MC goes down in to a special mode where it will only
respond to MCDI from the testing PF, and TX, RX and event queues are
torn down. Other PFs get a message as it goes down to tell them it's
going down.
When the other PFs get this message, they check the soft status
register to tell when the MC has rebooted after BIST mode and they can
start recovery.
[bwh: Convert the test result to 1 or -1 as for earlier NICs] Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The MC firmware is cooperatively multitasking and its scheduler will
send an event when a task yields after running for more than the
expected maximum time. This can be useful for firmware development
but does not usually indicate a serious error and does not help to
detect a lockup (there is a hardware watchdog that does that).
Change the message and reduce log level accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
sfc: Poll for MCDI completion once before timeout occurs
There is an as-yet unexplained bug that sometimes prevents (or delays)
the driver seeing the completion event for a completed MCDI request on
the SFC9120. The requested configuration change will have happened
but the driver assumes it to have failed, and this can result in
further failures. We can mitigate this by polling for completion
after unsuccessfully waiting for an event.
Fixes: 8127d661e77f ('sfc: Add support for Solarflare SFC9100 family') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Andrew Rybchenko [Sat, 16 Nov 2013 07:02:27 +0000 (11:02 +0400)]
sfc: RX buffer allocation takes prefix size into account in IP header alignment
rx_prefix_size is 4-bytes aligned on Falcon/Siena (16 bytes), but it is equal
to 14 on EF10. So, it should be taken into account if arch requires IP header
to be 4-bytes aligned (via NET_IP_ALIGN).
Fixes: 8127d661e77f ('sfc: Add support for Solarflare SFC9100 family') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Dec 2013 17:24:06 +0000 (17:24 +0000)]
sfc: Maintain current frequency adjustment when applying a time offset
There is a single MCDI PTP operation for setting the frequency
adjustment and applying a time offset to the hardware clock. When
applying a time offset we should not change the frequency adjustment.
These two operations can now be requested separately but this requires
a flash firmware update. Keep using the single operation, but
remember and repeat the previous frequency adjustment.
Fixes: 7c236c43b838 ('sfc: Add support for IEEE-1588 PTP') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Alexandre Rames [Fri, 8 Nov 2013 10:20:31 +0000 (10:20 +0000)]
sfc: Stop/re-start PTP when stopping/starting the datapath.
This disables PTP when we bring the interface down to avoid getting
unmatched RX timestamp events, and tries to re-enable it when bringing
the interface up.
[bwh: Make efx_ptp_stop() safe on Falcon. Introduce
efx_ptp_{start,stop}_datapath() functions; we'll expand them later.]
Fixes: 7c236c43b838 ('sfc: Add support for IEEE-1588 PTP') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Fri, 6 Dec 2013 22:10:46 +0000 (22:10 +0000)]
sfc: Rate-limit log message for PTP packets without a matching timestamp event
In case of a flood of PTP packets, the timestamp peripheral and MC
firmware on the SFN[56]322F boards may not be able to provide
timestamp events for all packets. Don't complain too much about this.
Fixes: 7c236c43b838 ('sfc: Add support for IEEE-1588 PTP') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Fri, 6 Dec 2013 19:26:40 +0000 (19:26 +0000)]
sfc: Add length checks to efx_xmit_with_hwtstamp() and efx_ptp_is_ptp_tx()
efx_ptp_is_ptp_tx() must be robust against skbs from raw sockets that
have invalid IPv4 and UDP headers.
Add checks that:
- the transport header has been found
- there is enough space between network and transport header offset
for an IPv4 header
- there is enough space after the transport header offset for a
UDP header
Fixes: 7c236c43b838 ('sfc: Add support for IEEE-1588 PTP') Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Eric Dumazet [Fri, 6 Dec 2013 06:36:05 +0000 (22:36 -0800)]
tcp: auto corking
With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.
Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)
If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.
This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.
The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.
Using FQ/pacing is a way to increase the probability of
autocorking being triggered.
Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)
Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.
Tested:
Interesting effects when using line buffered commands under ssh.
Excellent performance results in term of cpu usage and total throughput.
Yijing Wang [Fri, 6 Dec 2013 06:34:19 +0000 (14:34 +0800)]
net/fddi: Replace local macro with PCI standard macro
Replace local macro DFX_BUS_PCI() with PCI standard macro
dev_is_pci().
Acked-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 6 Dec 2013 05:38:06 +0000 (21:38 -0800)]
ipv6: consistent use of IP6_INC_STATS_BH() in ip6_forward()
ip6_forward() runs from softirq context, we can use the SNMP macros
assuming this.
Use same indentation for all IP6_INC_STATS_BH() calls.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:44 +0000 (09:13 -0800)]
net/*: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: John Fastabend <john.r.fastabend@intel.com> CC: Alex Duyck <alexander.h.duyck@intel.com> CC: Marcel Holtmann <marcel@holtmann.org> CC: Gustavo Padovan <gustavo@padovan.org> CC: Johan Hedberg <johan.hedberg@gmail.com> CC: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:43 +0000 (09:13 -0800)]
net/irda: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:42 +0000 (09:13 -0800)]
netfilter: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: netfilter@vger.kernel.org CC: Pablo Neira Ayuso <pablo@netfilter.org> CC: Patrick McHardy <kaber@trash.net> CC: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:41 +0000 (09:13 -0800)]
netlabel: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Paul Moore <paul@paul-moore.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:40 +0000 (09:13 -0800)]
include/net/: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 17:13:39 +0000 (09:13 -0800)]
ipv4/ipv6: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> CC: James Morris <jmorris@namei.org> CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 14:28:48 +0000 (06:28 -0800)]
sctp: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com> CC: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 14:28:47 +0000 (06:28 -0800)]
drivers/net/*: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Jay Vosburgh <fubar@us.ibm.com> CC: Veaceslav Falico <vfalico@redhat.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Haiyang Zhang <haiyangz@microsoft.com> CC: "K. Y. Srinivasan" <kys@microsoft.com> CC: Paul Mackerras <paulus@samba.org> CC: Ian Campbell <ian.campbell@citrix.com> CC: Wei Liu <wei.liu2@citrix.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: "Michael S. Tsirkin" <mst@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 14:28:46 +0000 (06:28 -0800)]
usb: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Oliver Neukum <oliver@neukum.org> CC: Steve Glendinning <steve.glendinning@shawell.net> CC: Oliver Neukum <oneukum@suse.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 14:28:44 +0000 (06:28 -0800)]
irda: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 6 Dec 2013 14:28:43 +0000 (06:28 -0800)]
ethernet: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Santosh Raspatur <santosh@chelsio.com> CC: Dimitris Michailidis <dm@chelsio.com> CC: Michael Chan <mchan@broadcom.com> CC: Santiago Leon <santil@linux.vnet.ibm.com> CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> CC: Olof Johansson <olof@lixom.net> CC: Manish Chopra <manish.chopra@qlogic.com> CC: Sony Chacko <sony.chacko@qlogic.com> CC: Rajesh Borundia <rajesh.borundia@qlogic.com> CC: Nicolas Pitre <nico@fluxnic.net> CC: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Wallace [Tue, 3 Dec 2013 10:55:22 +0000 (02:55 -0800)]
macvlan: Support creating macvtaps from macvlans
When running in a network namespace whose only link to the outside
world is a macvlan device, not being able to create a macvtap off of
it is a real pain.
So modify macvtap creation to automatically forward a creation of a
macvtap on a macvlan to become a creation of a macvtap on the
underlying network device, just like is currently done with
macvlan-on-macvlan devices.
v2: Use netif_is_macvlan and macvlan_dev_real_dev helpers to make it
more clear what we're doing.
Signed-off-by: Kevin Wallace <kevin@pentabarf.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 Dec 2013 00:45:14 +0000 (19:45 -0500)]
Merge branch 'siocghwtstamp' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 5 Dec 2013 21:02:56 +0000 (16:02 -0500)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this batch of fixes intende for the 3.13 stream!
For the mac80211 bits, Johannes says:
"For now I have various fixes all over, mostly for issues introduced in
relatively recent patches. There's no real pattern to it. Some of the
issues like go back longer, but still seemed 3.13 material."
And...
"These are just two patches disabling the broken CSA code. Once this
goes into your tree I'll merge it into mac80211-next and revert there
(since we fixed the bugs there)."
For the iwlwifi bits, Emmanuel says:
"I have here a few fixes for BT Coex. One of them is a NULL pointer
dereference. Another one avoids to enable a feature that can make the
firmware unhappy since the firmware isn't ready for it yet. WE also
avoid a WARNING that can be triggered upon association in not-so-bad
cases even if the association succeeded. We add support for new NICs
(not yet on the market) and bump the API so that 3.13 will be able to
work with the new firmware that will be out soon hopefully.
I also have a boundary check from Johannes."
In addition to those...
- Arend van Spriel fixes a brcmfmac problem that could use an
uninitialized variable in an error path.
- Borislav Petkov fixes a Kconfig-based build breakage problem for
brcmsmac.
- Michal Nazarewicz fixes a couple of NULL pointer dereference problems
in ath9k and wcn36xx.
- Sujith Manoharan fixes a couple of ath9k problems related to
incorrect interpretation of EEPROM configuration data.
- Ujjal Roy fixes a memory leak in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Dec 2013 21:55:49 +0000 (16:55 -0500)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
Fixes T5 adapter init, due to incorrect FW version check
This patch series fixes, Chelsio T5 adapter initialization failure due to
incorrect firmware version check. This patch series modifies the firmware
flashing mechanism for T4/T5 adapter.
The patch series moves chip type from struct adapter to struct adapter_params.
It changes the references of chip type in cxgb4 and cxgb4vf drivers such that
build failure is avoided.
Patch 3/3 is dependent on patch 1/3
Patch 2/3 is also dependent on patch 1/3
We would like to request this patch series to get merged via David Miller's
'net' tree.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rds: prevent BUG_ON triggered on congestion update to loopback
After congestion update on a local connection, when rds_ib_xmit returns
less bytes than that are there in the message, rds_send_xmit calls
back rds_ib_xmit with an offset that causes BUG_ON(off & RDS_FRAG_SIZE)
to trigger.
For a 4Kb PAGE_SIZE rds_ib_xmit returns min(8240,4096)=4096 when actually
the message contains 8240 bytes. rds_send_xmit thinks there is more to send
and calls rds_ib_xmit again with a data offset "off" of 4096-48(rds header)
=4048 bytes thus hitting the BUG_ON(off & RDS_FRAG_SIZE) [RDS_FRAG_SIZE=4k].
The commit 6094628bfd94323fc1cea05ec2c6affd98c18f7f
"rds: prevent BUG_ON triggering on congestion map updates" introduced
this regression. That change was addressing the triggering of a different
BUG_ON in rds_send_xmit() on PowerPC architecture with 64Kbytes PAGE_SIZE:
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
This was the sequence it was going through:
(rds_ib_xmit)
/* Do not send cong updates to IB loopback */
if (conn->c_loopback
&& rm->m_inc.i_hdr.h_flags & RDS_FLAG_CONG_BITMAP) {
rds_cong_map_updated(conn->c_fcong, ~(u64) 0);
return sizeof(struct rds_header) + RDS_CONG_MAP_BYTES;
}
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 0 + 8240 - 48 (rds header accounted only the first time)
= 8192
c_xmit_data_off < 65536 (sg->length), so calls rds_ib_xmit again
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 8192 + 8240 = 16432, calls rds_ib_xmit again
and so on (c_xmit_data_off 24672,32912,41152,49392,57632)
rds_ib_xmit returns 8240
On this iteration this sequence causes the BUG_ON in rds_send_xmit:
while (ret) {
tmp = min_t(int, ret, sg->length - conn->c_xmit_data_off);
[tmp = 65536 - 57632 = 7904]
conn->c_xmit_data_off += tmp;
[c_xmit_data_off = 57632 + 7904 = 65536]
ret -= tmp;
[ret = 8240 - 7904 = 336]
if (conn->c_xmit_data_off == sg->length) {
conn->c_xmit_data_off = 0;
sg++;
conn->c_xmit_sg++;
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
[c_xmit_sg = 1, rm->data.op_nents = 1]
What the current fix does:
Since the congestion update over loopback is not actually transmitted
as a message, all that rds_ib_xmit needs to do is let the caller think
the full message has been transmitted and not return partial bytes.
It will return 8240 (RDS_CONG_MAP_BYTES+48) when PAGE_SIZE is 4Kb.
And 64Kb+48 when page size is 64Kb.
Reported-by: Josh Hunt <joshhunt00@gmail.com> Tested-by: Honggang Li <honli@redhat.com> Acked-by: Bang Nguyen <bang.nguyen@oracle.com> Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Tue, 3 Dec 2013 14:06:25 +0000 (14:06 +0000)]
xen-netback: clear vif->task on disconnect
xenvif_start_xmit() relies on checking vif->task for NULL to determine
whether the vif is ready to accept packets. The task thread is stopped in
xenvif_disconnect() but task is not set to NULL. Thus, on a re-connect the
check will give a false positive.
Also since commit ea732dff5cfa10789007bf4a5b935388a0bb2a8f (Handle backend
state transitions in a more robust way) it should not be possible for
xenvif_connect() to be called if the vif is already connected so change the
check of vif->tx_irq to a BUG_ON() and also add a BUG_ON(vif->task).
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It causes regressions for people using chips driven by the sungem
driver. Suspicion is that the skb->csum value isn't being adjusted
properly.
The change also has a bug in that if __pskb_trim() fails, we'll leave
a corruped skb->csum value in there. We would really need to revert
it to it's original value in that case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 2 Dec 2013 16:51:13 +0000 (08:51 -0800)]
net: do not pretend FRAGLIST support
Few network drivers really supports frag_list : virtual drivers.
Some drivers wrongly advertise NETIF_F_FRAGLIST feature.
If skb with a frag_list is given to them, packet on the wire will be
corrupt.
Remove this flag, as core networking stack will make sure to
provide packets that can be sent without corruption.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Anirudha Sarangi <anirudh@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamala R [Mon, 2 Dec 2013 14:25:21 +0000 (19:55 +0530)]
IPv6: Fixed support for blackhole and prohibit routes
The behaviour of blackhole and prohibit routes has been corrected by setting
the input and output pointers of the dst variable appropriately. For
blackhole routes, they are set to dst_discard and to ip6_pkt_discard and
ip6_pkt_discard_out respectively for prohibit routes.
ipv6: ip6_pkt_prohibit(_out) should not depend on
CONFIG_IPV6_MULTIPLE_TABLES
We need ip6_pkt_prohibit(_out) available without
CONFIG_IPV6_MULTIPLE_TABLES
Signed-off-by: Kamala R <kamala@aristanetworks.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fec_main: dma_map() only the length of the skb
On tx submit the driver always dma_map_single() FEC_ENET_TX_FRSIZE (=2048)
bytes. This works because we don't overwrite any memory after the data buffer,
we remove it from cache if it was there. So we hurt performace in case the
mapping of a smaller area makes a difference.
There is also a bug: If the data area starts shortly before the end of
RAM say 0xc7fffa10 and the RAM ends at 0xc8000000 then we have enough
space to fit the data area (according to skb->len) but we would map beyond
end of ram if we are using 2048. In v2.6.31 (against which kernel this patch
made) there is the following check in dma_cache_maint():
Since the area starting at 0xc8000000 is no longer virt_addr_valid() we
BUG() during dma_map_single(). The BUG() statement was removed in v3.5-rc1 as
per 2dc6a016 ("ARM: dma-mapping: use asm-generic/dma-mapping-common.h").
This patch was tested on v2.6.31 and then forward-ported and compile
tested only against the net tree. I think it is still worth fixing
mainline even after the BUG() statement is gone.
Tested-by: Fugang Duan <B38611@freescale.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 2 Dec 2013 07:23:39 +0000 (12:53 +0530)]
drivers: net: cpsw: fix dt probe for one port ethernet
When only one port of the two port is pinned out, then dt probe is failing
because second port phy is not found. fixing this by checking the number of
slaves and breaking the loop.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI / tg3: Give up chip reset and carrier loss handling if PCI device is not present
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Duan Jiong [Tue, 26 Nov 2013 07:46:56 +0000 (15:46 +0800)]
ipv6: judge the accept_ra_defrtr before calling rt6_route_rcv
when dealing with a RA message, if accept_ra_defrtr is false,
the kernel will not add the default route, and then deal with
the following route information options. Unfortunately, those
options maybe contain default route, so let's judge the
accept_ra_defrtr before calling rt6_route_rcv.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 2 Dec 2013 18:15:39 +0000 (10:15 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
Linus Torvalds [Mon, 2 Dec 2013 18:13:44 +0000 (10:13 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various smaller fixlets, all over the place"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Fix generation of device-drivers
sched: Expose preempt_schedule_irq()
sched: Fix a trivial typo in comments
sched: Remove unused variable in 'struct sched_domain'
sched: Avoid NULL dereference on sd_busy
sched: Check sched_domain before computing group power
MAINTAINERS: Update file patterns in the lockdep and scheduler entries
Linus Torvalds [Mon, 2 Dec 2013 18:13:09 +0000 (10:13 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
Linus Torvalds [Mon, 2 Dec 2013 18:12:01 +0000 (10:12 -0800)]
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
Arend van Spriel [Fri, 29 Nov 2013 22:00:31 +0000 (23:00 +0100)]
brcmfmac: fix uninitialized warning
Building brcmfmac for sparc64 gave the following warning:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
bcmsdh_sdmmc.c: In function 'brcmf_sdioh_request_byte':
bcmsdh_sdmmc.c:89:6: warning: 'err_ret' may be used uninitialized
in this function [-Wuninitialized]
Inspecting the code it indeed had a path of execution in
which the return value was used uninitialized. This patch
fixes that code path.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kmalloc fails wcn36xx_smd_rsp_process will attempt to dereference
a NULL pointer. There might be a better error recovery then just
printing an error, but printing an error message is better then the
current behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
net: wireless: ath9k: avoid possible NULL pointer dereference
Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL. If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL. Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 26 Nov 2013 01:51:39 +0000 (07:21 +0530)]
ath9k: Fix XLNA bias strength
The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.
Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 26 Nov 2013 01:51:08 +0000 (07:21 +0530)]
ath9k: Fix QuickDrop usage
Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.
Cc: stable@vger.kernel.org Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Mon, 2 Dec 2013 18:10:55 +0000 (10:10 -0800)]
Merge tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix
for an embarrassing thinko in the new devm master registration code"
* tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Restore private register bits.
spi/qspi: Fix qspi remove path.
spi/qspi: cleanup pm_runtime error check.
spi/qspi: set correct platform drvdata in ti_qspi_probe()
spi/pxa2xx: add new ACPI IDs
spi: core: invert success test in devm_spi_register_master
spi: spi-mxs: fix reference leak to master in mxs_spi_remove()
spi: bcm63xx: fix reference leak to master in bcm63xx_spi_remove()
spi: txx9: fix reference leak to master in txx9spi_remove()
spi: mpc512x: fix reference leak to master in mpc512x_psc_spi_do_remove()
spi: rspi: use platform drvdata correctly in rspi_remove()
spi: bcm2835: fix reference leak to master in bcm2835_spi_remove()
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
Linus Torvalds [Mon, 2 Dec 2013 17:44:51 +0000 (09:44 -0800)]
vfs: fix subtle use-after-free of pipe_inode_info
The pipe code was trying (and failing) to be very careful about freeing
the pipe info only after the last access, with a pattern like:
spin_lock(&inode->i_lock);
if (!--pipe->files) {
inode->i_pipe = NULL;
kill = 1;
}
spin_unlock(&inode->i_lock);
__pipe_unlock(pipe);
if (kill)
free_pipe_info(pipe);
where the final freeing is done last.
HOWEVER. The above is actually broken, because while the freeing is
done at the end, if we have two racing processes releasing the pipe
inode info, the one that *doesn't* free it will decrement the ->files
count, and unlock the inode i_lock, but then still use the
"pipe_inode_info" afterwards when it does the "__pipe_unlock(pipe)".
This is *very* hard to trigger in practice, since the race window is
very small, and adding debug options seems to just hide it by slowing
things down.
Simon originally reported this way back in July as an Oops in
kmem_cache_allocate due to a single bit corruption (due to the final
"spin_unlock(pipe->mutex.wait_lock)" incrementing a field in a different
allocation that had re-used the free'd pipe-info), it's taken this long
to figure out.
Since the 'pipe->files' accesses aren't even protected by the pipe lock
(we very much use the inode lock for that), the simple solution is to
just drop the pipe lock early. And since there were two users of this
pattern, create a helper function for it.
Introduced commit ba5bb147330a ("pipe: take allocation and freeing of
pipe_inode_info out of ->i_mutex").
Reported-by: Simon Kirby <sim@hostway.ca> Reported-by: Ian Applegate <ia@cloudflare.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # v3.10+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simon Wunderlich [Tue, 26 Nov 2013 15:45:18 +0000 (16:45 +0100)]
mac80211: check csa wiphy flag in ibss before switching
When external CSA IEs are received (beacons or action messages), a
channel switch is triggered as well. This should only be allowed on
devices which actually support channel switches, otherwise disconnect.
(For the corresponding userspace invocation, the wiphy flag is checked
in nl80211).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simon Wunderlich [Tue, 26 Nov 2013 15:07:26 +0000 (16:07 +0100)]
cfg80211: disable CSA for all drivers
The channel switch announcement code has some major locking problems
which can cause a deadlock in worst case. A series of fixes has been
proposed, but these are non-trivial and need to be tested first.
Therefore disable CSA completely for 3.13.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove waiting for TX queues to become empty during selftest.
This check is not necessary for any purpose, and might put
the driver into an infinite loop.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fan.du [Sun, 1 Dec 2013 08:28:48 +0000 (16:28 +0800)]
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
commit a553e4a6317b2cfc7659542c10fe43184ffe53da ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net: fix error handling for mergeable buffers
Eric Dumazet noticed that if we encounter an error
when processing a mergeable buffer, we don't
dequeue all of the buffers from this packet,
the result is almost sure to be loss of networking.
Jason Wang noticed that we also leak a page and that we don't decrement
the rq buf count, so we won't repost buffers (a resource leak).
Fix both issues.
Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Michael Dalton <mwdalton@google.com> Reported-by: Eric Dumazet <edumazet@google.com> Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 1 Dec 2013 23:33:53 +0000 (15:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"Fixes two regressions which got introduced this merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Build always with -mcmodel=large on 64bit
um: Rename print_stack_trace to do_stack_trace
Linus Torvalds [Sun, 1 Dec 2013 23:32:19 +0000 (15:32 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Some ARM fixes, the biggest of which is the fix for the signal return
codes; this came up due to an interaction between the V7M nommu
changes and the BE8 changes. Dave Martin spotted that the kexec
trampoline wasn't being correctly copied (in a way which allows
Thumb-2 to work).
I've also fixed a number of breakages on footbridge platforms as I've
upgraded one of my machines to v3.12... one which had a 1200 day
uptime"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7907/1: lib: delay-loop: Add align directive to fix BogoMIPS calculation
ARM: 7897/1: kexec: Use the right ISA for relocate_new_kernel
ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S
ARM: footbridge: fix EBSA285 LEDs
ARM: footbridge: fix VGA initialisation
ARM: fix booting low-vectors machines
ARM: dma-mapping: check DMA mask against available memory
On UML SUBARCH can be x86, x86_64 and i386 and if it is x86
we use uname -m to select a defconfig.
Therefore we can no longer use -mcmodel=large only if SUBARCH
is x86_64.
Reported-and-tested-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Currently mx53 (CortexA8) running at 1GHz reports:
Calibrating delay loop... 663.55 BogoMIPS (lpj=3317760)
Tom Evans verified that alignments of 0x0 and 0x8 run the two instructions of __loop_delay in one clock cycle (1 clock/loop), while alignments of 0x4 and 0xc take 3 clocks to run the loop twice. (1.5 clock/loop)
, which now reports:
Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
Some more test results:
On mx31 (ARM1136) running at 532 MHz, before the patch:
Calibrating delay loop... 351.43 BogoMIPS (lpj=1757184)
On mx31 (ARM1136) running at 532 MHz after the patch:
Calibrating delay loop... 528.79 BogoMIPS (lpj=2643968)
Also tested on mx6 (CortexA9) and on mx27 (ARM926), which shows the same
BogoMIPS value before and after this patch.
Reported-by: Tom Evans <tom_usenet@optusnet.com.au> Suggested-by: Tom Evans <tom_usenet@optusnet.com.au> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Mon, 25 Nov 2013 13:54:47 +0000 (14:54 +0100)]
ARM: 7897/1: kexec: Use the right ISA for relocate_new_kernel
Copying a function with memcpy() and then trying to execute the
result isn't trivially portable to Thumb.
This patch modifies the kexec soft restart code to copy its
assembler trampoline relocate_new_kernel() using fncpy() instead,
so that relocate_new_kernel can be in the same ISA as the rest of
the kernel without problems.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Tested-by: Taras Kondratiuk <taras.kondratiuk@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Victor Kamensky [Thu, 21 Nov 2013 06:17:03 +0000 (07:17 +0100)]
ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S
After "ARM: signal: sigreturn_codes should be endian neutral to
work in BE8" commit, thumb only platforms, like armv7m, fails to
compile sigreturn_codes.S. The reason is that for such arch
values '.arm' directive and arm opcodes are not allowed.
Fix conditionally enables arm opcodes only if no CONFIG_CPU_THUMBONLY
defined and it uses .org instructions to keep sigreturn_codes
layout.
Suggested-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 29 Nov 2013 00:54:38 +0000 (00:54 +0000)]
ARM: footbridge: fix EBSA285 LEDs
- The LEDs register is write-only: it can't be read-modify-written.
- The LEDs are write-1-for-off not 0.
- The check for the platform was inverted.
Fixes: cf6856d693dd ("ARM: mach-footbridge: retire custom LED code") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: stable@vger.kernel.org
Patch from developers of the alternative loss models, downloaded from:
http://netgroup.uniroma2.it/twiki/bin/view.cgi/Main/NetemCLG
"in case 2, of the switch we change the direction of the inequality to
net_random()>clg->a3, because clg->a3 is h in the GE model and when h
is 0 all packets will be lost."
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a missing break statement in the Gilbert Elliot loss model
generator which makes state machine behave incorrectly.
Reported-by: Martin Burri <martin.burri@ch.abb.com Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: fix possible seqlock deadlock in ip6_finish_output2
IPv6 stats are 64 bits and thus are protected with a seqlock. By not
disabling bottom-half we could deadlock here if we don't disable bh and
a softirq reentrantly updates the same mib.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 30 Nov 2013 17:42:20 +0000 (12:42 -0500)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, e1000 and ixgbe.
Akeem provides a igb fix where WOL was being reported as supported on
some ethernet devices which did not have that capability.
Yanjun provides a fix for e1000 which is similar to a previous fix
for e1000e commit bb9e44d0d0f4 ("e1000e: prevent oops when adapter is
being closed and reset simultaneously"), where the same issue was
observed on the older e1000 cards.
Vladimir Davydov provides 2 e1000 fixes. The first fixes a lockdep
warning e1000_down() tries to synchronously cancel e1000 auxiliary
works (reset_task, watchdog_task, phy_info_task and fifo_stall_task)
which take adapter->mutex in their handlers. The second patch is to
fix a possible race condition where reset_task() would be running
after adapter down.
John provides 2 fixes for ixgbe. First turns ixgbe_fwd_ring_down
to static and the second disables NETIF_F_HW_L2FW_DOFFLOAD by default
because it allows upper layer net devices to use queues in the hardware
to directly submit and receive skbs.
Mark Rustad provides a single patch for ixgbe to make
ixgbe_identify_qsfp_module_generic static to resolve compile
warnings.
v2: Drop igb patch "igb: Update queue reinit function to call dev_close
when init of queues fails" from Carolyn, so that the solution can
be re-worked based on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 28 Nov 2013 21:43:40 +0000 (21:43 +0000)]
ARM: fix booting low-vectors machines
Commit f6f91b0d9fd9 (ARM: allow kuser helpers to be removed from the
vector page) required two pages for the vectors code. Although the
code setting up the initial page tables was updated, the code which
allocates page tables for new processes wasn't, neither was the code
which tears down the mappings. Fix this.
Fixes: f6f91b0d9fd9 ("ARM: allow kuser helpers to be removed from the vector page") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: <stable@vger.kernel.org>
Russell King [Mon, 25 Nov 2013 21:52:25 +0000 (21:52 +0000)]
ARM: dma-mapping: check DMA mask against available memory
Some buses have negative offsets, which causes the DMA mask checks to
falsely fail. Fix this by using the actual amount of memory fitted in
the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Rustad [Sat, 23 Nov 2013 03:19:19 +0000 (03:19 +0000)]
ixgbe: Make ixgbe_identify_qsfp_module_generic static
Correct a namespace complaint by making the function static
and moving the prototype into the .c file.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Tue, 12 Nov 2013 12:13:29 +0000 (12:13 +0000)]
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
NETIF_F_HW_L2FW_DOFFLOAD allows upper layer net devices such
as macvlan to use queues in the hardware to directly submit and
receive skbs.
This creates a subtle change in the datapath though. One change
being the skb may no longer use the root devices qdisc.
Because users may not expect this we can't enable the feature
by default unless the hardware can offload all the software
functionality above it. So for now disable it by default and
let users opt in.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Vladimir Davydov [Sat, 23 Nov 2013 07:18:01 +0000 (07:18 +0000)]
e1000: fix possible reset_task running after adapter down
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Vladimir Davydov <vdavydov@parallels.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / linux-beck.git / log