Steven Rostedt [Wed, 17 Jun 2009 01:22:48 +0000 (21:22 -0400)]
ring-buffer: do not grab locks in nmi
If ftrace_dump_on_oops is set, and an NMI detects a lockup, then it
will need to read from the ring buffer. But the read side of the
ring buffer still takes locks. This patch adds a check on the read
side that if it is in an NMI, then it will disable the ring buffer
and not take any locks.
Reads can still happen on a disabled ring buffer.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Wed, 17 Jun 2009 18:11:10 +0000 (14:11 -0400)]
ring-buffer: check for less than two in size allocation
The ring buffer must have at least two pages allocated for the
reader page swap to work.
The page count check will miss the case of a zero size passed in.
Even though a zero size ring buffer would probably fail an allocation,
making the min size check for less than two instead of equal to one makes
the code a bit more robust.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Wed, 17 Jun 2009 18:03:44 +0000 (14:03 -0400)]
ring-buffer: remove useless compile check for buffer_page size
The original version of the ring buffer had a hack to map the
page struct that held the pages of the buffer to also be the structure
that the ring buffer would keep the pages in a link list.
This overlap of the page struct was very dangerous and that hack was
removed a while ago.
But there was a check to make sure the buffer_page never became bigger
than the page struct, and would fail the compile if it did. The
check was only meaningful when we had the hack. Now that we have separate
allocated descriptors for the buffer pages, we can remove this check.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 11 Jun 2009 13:29:58 +0000 (09:29 -0400)]
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
The index of the event is found by masking PAGE_MASK to it and
subtracting the header size. Currently the header size is calculate
by PAGE_SIZE - BUF_PAGE_SIZE, when we already have a macro
BUF_PAGE_HDR_SIZE to define it.
If we want to change BUF_PAGE_SIZE to something less than filling
the rest of the page (this is done for debugging), then we break
the algorithm to find the index.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Tue, 16 Jun 2009 16:37:57 +0000 (12:37 -0400)]
ring-buffer: use commit counters for commit pointer accounting
The ring buffer is made up of three sets of pointers.
The head page pointer, which points to the next page for the reader to
get.
The commit pointer and commit index, which points to the page and index
of the last committed write respectively.
The tail pointer and tail index, which points to the page and the index
of the last reserved data respectively (non committed).
The commit pointer is only moved forward by the outer most writer.
If a nested writer comes in, it will not move the pointer forward.
The current implementation has a flaw. It assumes that the outer most
writer successfully reserved data. There's a small race window where
the outer most writer could find the tail pointer, but a nested
writer could come in (via interrupt) and move the tail forward, and
even the commit forward.
The outer writer would not realized the commit moved forward and the
accounting will break.
This patch changes the design to use counters in the per cpu buffers
to keep track of commits. The counters are incremented at the start
of the commit, and decremented at the end. If the end commit counter
is 1, then it moves the commit pointers. A loop is made to check for
races between checking and moving the commit pointers. Only the outer
commit should move the pointers anyway.
The test of knowing if a reserve is equal to the last commit update
is still needed to know for time keeping. The time code is much less
racey than the commit updates.
This change not only solves the mentioned race, but also makes the
code simpler.
[ Impact: fix commit race and simplify code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The ring buffer may now add discarded events when a write passes
the end of a buffer page. Before, a discarded event was only added
when the tracer deliberately created one. The ring buffer benchmark
test does not handle discarded events when it reads the buffer and
fails when it encounters one.
Also fix the increment for large data entries (luckily, the test did
not add any yet).
[ Impact: fix false failure of ring buffer self test ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 11 Jun 2009 15:12:00 +0000 (11:12 -0400)]
ring-buffer: prevent adding write in discarded area
This a very tight race where an interrupt could come in and not
have enough data to put into the end of a buffer page, and that
it would fail to write and need to go to the next page.
But if this happened when another writer was about to reserver
their data, and that writer has smaller data to reserve, then
it could succeed even though the interrupt moved the tail page.
To pervent that, if we fail to store data, and by subtracting the
amount we reserved we still have room for smaller data, we need
to fill that space with "discarded" data.
[ Impact: prevent race were buffer data may be lost ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Li Zefan [Mon, 15 Jun 2009 02:59:17 +0000 (10:59 +0800)]
tracing/filters: strloc should be unsigned short
I forgot to update filter code accordingly in
"tracing/events: change the type of __str_loc_item to unsigned short"
(commt b0aae68cc5508f3c2fbf728988c954db4c8b8a53)
Wu Zhangjin [Sun, 14 Jun 2009 06:52:30 +0000 (14:52 +0800)]
tracing: fix undeclared 'PAGE_SIZE' in include/linux/trace_seq.h
when compiling linux-mips with kmemtrace enabled, there will be an
error:
include/linux/trace_seq.h:12: error: 'PAGE_SIZE' undeclared here (not in
a function)
I checked the source code and found trace_seq.h used PAGE_SIZE but not
included the relative header file, so, fix it via adding the header file
<asm/page.h>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
LKML-Reference: <1244962350-28702-1-git-send-email-wuzhangjin@gmail.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Rusty Russell [Fri, 12 Jun 2009 11:45:30 +0000 (21:15 +0930)]
cpumask: use new operators in kernel/trace
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <200906122115.30787.rusty@rustcorp.com.au> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Sun, 14 Jun 2009 21:12:18 +0000 (14:12 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (53 commits)
.gitignore: ignore *.lzma files
kbuild: add generic --set-str option to scripts/config
kbuild: simplify argument loop in scripts/config
kbuild: handle non-existing options in scripts/config
kallsyms: generalize text region handling
kallsyms: support kernel symbols in Blackfin on-chip memory
documentation: make version fix
kbuild: fix a compile warning
gitignore: Add GNU GLOBAL files to top .gitignore
kbuild: fix delay in setlocalversion on readonly source
README: fix misleading pointer to the defconf directory
vmlinux.lds.h update
kernel-doc: cleanup perl script
Improve vmlinux.lds.h support for arch specific linker scripts
kbuild: fix headers_exports with boolean expression
kbuild/headers_check: refine extern check
kbuild: fix "Argument list too long" error for "make headers_check",
ignore *.patch files
Remove bashisms from scripts
menu: fix embedded menu presentation
...
Linus Torvalds [Sun, 14 Jun 2009 20:53:22 +0000 (13:53 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
In addition to KT_DEAD which has limited support for diacriticals,
there is KT_DEAD2 that can support 256 criticals, so let's advertise
it in <linux/keyboard.h>.
This lets userland know abut the drivers/char/keyboard.c function
k_dead2, which supports more than the few trivial ones that k_dead
supports.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Jun 2009 20:46:57 +0000 (13:46 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
atmel-mci: add MCI2 register definitions
atmel-mci: Integrate AT91 specific definition in header file
tmio_mmc: allow compilation for ASIC3
mmc_block: do not DMA to stack
sdhci: Print ADMA status and pointer on debug
tmio_mmc: fix clock setup
tmio_mmc: map SD control registers after enabling the MFD cell
tmio_mmc: correct probe return value for num_resources != 3
tmio_mmc: don't use set_irq_type
tmio_mmc: add bus_shift support
MFD,mmc: tmio_mmc: make HCLK configurable
mmc_spi: don't use EINVAL for possible transmission errors
cb710: more cleanup for the DEBUG case.
sdhci: platform driver for SDHCI
mxcmmc: remove frequency workaround
cb710: handle DEBUG define in Makefile
cb710: add missing parenthesis
cb710: fix printk format string
mmc: Driver for CB710/720 memory card reader (MMC part)
pxamci: add regulator support.
...
Linus Torvalds [Sun, 14 Jun 2009 20:45:49 +0000 (13:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix inverted wheel for bluetooth version of apple mighty mouse
HID: no more reinitializtion is needed in post_reset
HID: hidraw -- fix comment about accepted devices
HID: Multitouch support for the N-Trig touchscreen
HID: add new multitouch and digitizer contants
HID: autocentering support for Logitech Force 3D Pro
HID: fix hid-ff drivers so that devices work even without ff support
HID: force feedback support for SmartJoy PLUS PS2/USB adapter
HID: Wacom Graphire Bluetooth driver
HID: autocentering support for Logitech G25 Racing Wheel
Robin Getz [Mon, 10 Jul 2006 06:25:40 +0000 (06:25 +0000)]
kallsyms: support kernel symbols in Blackfin on-chip memory
The Blackfin arch has a discontiguous .text layout due to having on-chip
instruction memory and no virtual memory support. As such, we need to
add explicit checks for these additional .text regions.
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus Torvalds [Sun, 14 Jun 2009 20:42:43 +0000 (13:42 -0700)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
The Makefiles in the build directories use the internal make variable
MAKEFILE_LIST which is available from make 3.80 only. (The patch would be
valid back to 2.6.25)
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Roland Dreier [Sun, 14 Jun 2009 20:30:45 +0000 (13:30 -0700)]
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time. This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Nicolas Pitre [Fri, 12 Jun 2009 02:09:29 +0000 (03:09 +0100)]
[ARM] 5545/2: add flush_kernel_dcache_page() for ARM
Without this, the default implementation is a no op which is completely
wrong with a VIVT cache, and usage of sg_copy_buffer() produces
unpredictable results.
Tested-by: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc> CC: stable@kernel.org Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Roland Dreier [Sat, 13 Jun 2009 22:14:09 +0000 (15:14 -0700)]
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com> Tested-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ben Dooks [Mon, 8 Jun 2009 22:33:57 +0000 (23:33 +0100)]
mmc_block: do not DMA to stack
In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.
Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.
[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Ian Molton [Fri, 12 Jun 2009 20:53:05 +0000 (21:53 +0100)]
tmio_mmc: fix clock setup
This patch fixes the clock setup in tmio_mmc.
* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))
It also eliminates some unnecessary ifs and tidies the loop syntax.
Thanks to Philipp Zabel who discovered the divider issue, commenting
"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency.
The smallest possible frequency (f_max/512) is configured with
a divider setting 0x80, not 0x40."
Signed-off-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Philipp Zabel [Thu, 4 Jun 2009 18:12:32 +0000 (20:12 +0200)]
tmio_mmc: add bus_shift support
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Philipp Zabel [Thu, 4 Jun 2009 18:12:31 +0000 (20:12 +0200)]
MFD,mmc: tmio_mmc: make HCLK configurable
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Ian Molton <ian@mnementh.co.uk> Acked-by: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Wolfgang Muees [Tue, 26 May 2009 07:56:19 +0000 (08:56 +0100)]
mmc_spi: don't use EINVAL for possible transmission errors
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Acked-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Michał Mirosław [Fri, 22 May 2009 18:33:59 +0000 (20:33 +0200)]
mmc: Driver for CB710/720 memory card reader (MMC part)
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Daniel Ribeiro [Thu, 21 May 2009 11:54:18 +0000 (08:54 -0300)]
pxamci: add regulator support.
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
mmc/omap: make mmci-omap using platform_driver_probe
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Wolfgang Muees [Wed, 8 Apr 2009 09:14:07 +0000 (10:14 +0100)]
mmc_spi: speedup for slow cards, less wear-out
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Jorg Schummer [Tue, 31 Mar 2009 14:51:21 +0000 (17:51 +0300)]
mmc: mmc_rescan detects card change in one run
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com> Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
The problem is that asm/signal.h has been made to include asm-generic/signal.h,
but the redundant stuff from asm/signal.h has not been discarded, leading to
multiple redefinitions.
Linus Torvalds [Sat, 13 Jun 2009 20:15:59 +0000 (13:15 -0700)]
Merge branch 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-ocores: Can add I2C devices to the bus
i2c-s3c2410: move to using platform idtable to match devices
i2c: OMAP3: Better noise suppression for fast/standard modes
i2c: OMAP2/3: Fix scll/sclh calculations
i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionality
i2c: Blackfin TWI: fix transfer errors with repeat start
i2c: Blackfin TWI: fix REPEAT START mode doesn't repeat
i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0
Linus Torvalds [Sat, 13 Jun 2009 20:08:34 +0000 (13:08 -0700)]
Merge branch 'docs-next' of git://git.lwn.net/linux-2.6
* 'docs-next' of git://git.lwn.net/linux-2.6:
Document the debugfs API
Documentation: Add "how to write a good patch summary" to SubmittingPatches
SubmittingPatches: fix typo
docs: Encourage better changelogs in the development process document
Document Reported-by in SubmittingPatches
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
Ingo Molnar [Sat, 13 Jun 2009 06:29:33 +0000 (08:29 +0200)]
[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
Caused by not including linux/module.h
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
Richard Röjfors [Fri, 5 Jun 2009 13:40:32 +0000 (15:40 +0200)]
i2c-ocores: Can add I2C devices to the bus
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Fri, 12 Jun 2009 09:45:29 +0000 (10:45 +0100)]
i2c-s3c2410: move to using platform idtable to match devices
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Frank Shew [Tue, 19 May 2009 11:23:49 +0000 (07:23 -0400)]
i2c: Blackfin TWI: fix transfer errors with repeat start
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject] Signed-off-by: Ben Dooks <ben-linux@fluff.org>
projects / linux-beck.git / log