Haim Dreyfuss [Sun, 27 Mar 2016 09:56:13 +0000 (12:56 +0300)]
iwlwifi: pcie: Fix index iteration on free_irq in MSIX mode
In MSIX mode we iterate over the allocated interrupt vectors and
register them to an handler. In case of registration failure,
we free all the allocated irq.
we use the outer index mistakenly instead of the inner one.
_UCODE_API_OK was a intermediate version between MIN and
MAX. If a user had a firmware below _OK but above _MIN, the
driver would work but the user would get a warning in the
kernel log telling him to update his firmware.
This is not needed since most users won't look for these
messages in the kernel log if their wifi is working.
Luca Coelho [Fri, 11 Mar 2016 07:20:37 +0000 (09:20 +0200)]
iwlwifi: mvm: add a scan timeout for regular scans
If something goes wrong with the firmware and we never get a scan
complete notification, we stay stuck forever. In order to avoid this
situation, add a timeout and trigger an NMI if it expires before
receiving the notification., so we can clean things up.
Liad Kaufman [Sun, 28 Feb 2016 14:15:07 +0000 (16:15 +0200)]
iwlwifi: mvm: set sta_id in SCD_QUEUE_CONFIG cmd
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
Sara Sharon [Tue, 22 Mar 2016 13:55:58 +0000 (15:55 +0200)]
iwlwifi: mvm: improve RSS configuration
Improve current RSS configuration:
* Use netdev_rss_key instead of keeping a local copy.
* Configure also UDP hashing to have UDP traffic spread across queues.
* Do not direct RSS traffic to our fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Tue, 22 Mar 2016 14:04:53 +0000 (16:04 +0200)]
iwlwifi: pcie: request one more interrupt vector
We want to request an interrupt vector for RSS queue per CPU,
one vector for fallback queue, and one for non-rx interrupts.
Future patch will make sure that no RSS traffic is directed to
fallback queue.
This will enable us to enable fast path on traffic that otherwise
would have been received on the fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Wed, 16 Mar 2016 11:57:50 +0000 (13:57 +0200)]
iwlwifi: mvm: report checksum is done also for IPv6 packets
Currently the code checks if hardware reported both L4 and L3
checksums as valid, and only then reports it as validated to
the stack.
However, IPv6 does not have checksum at all and the L3 checksum
valid bit is always off for IPv6 packets, with the result of the
stack re-validating L4 checksum.
Fix code to set CHECKSUM_UNNECESSARY also for IPv6 packets whose
TCP/UDP checksum was verified.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use alloc_ordered_workqueue() to allocate the workqueue instead of
create_singlethread_workqueue() since the latter is deprecated and is scheduled
for removal.
There are work items doing related operations that shouldn't be swapped when
queued in a certain order hence preserve the strict execution ordering of a
single threaded (ST) workqueue by switching to alloc_ordered_workqueue().
WQ_MEM_RECLAIM flag is not needed since the worker is not depended
during memory reclaim.
Sara Sharon [Wed, 16 Mar 2016 14:28:42 +0000 (16:28 +0200)]
iwlwifi: pcie: write to legacy register also in MQ
Due to hardware bug, upon any shadow free-queue register write
access, a legacy RBD shadow register must be written as well.
This is required in order to trigger a copy of the shadow registers
values after MAC exits sleep state.
Specifically, the driver has to write (any value) to the legacy RBD
register each time FRBDCB is accessed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: support bss dynamic alloc/dealloc of queues
"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.
Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.
There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.
This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.
When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.
When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Haim Dreyfuss [Tue, 15 Mar 2016 08:51:40 +0000 (10:51 +0200)]
iwlwifi: 9000: update device id and FW serial number
Update device id and FW serial number for 2X2 antenna devices
in 9000 generation product. These will not be available on
the market in the coming year.
Sara Sharon [Wed, 9 Mar 2016 08:12:45 +0000 (10:12 +0200)]
iwlwifi: mvm: add support for new TX CMD API
TX CMD API has changed to support offload assist.
Currently we do not enable checksum yet, but must set the
padding indication, to avoid FW errors.
Set other amsdu flag as well.
The rest of the flags will be configured only if HW csum
is enabled and will be set in future patches.
This change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Sun, 13 Mar 2016 15:19:38 +0000 (17:19 +0200)]
iwlwifi: pcie: do not pad QoS AMSDU
We insert padding if the MAC header's size is not a multiple of 4
to ensure that the SNAP header is DWORD aligned. When we do so, we
let the firmware know by setting a bit in Tx command
(TX_CMD_FLG_MH_PAD) which will instruct the firmware to drop those
2 bytes before sending the frame.
However, this is not needed for AMSDU as the sub frame header (14B)
complements the MAC header (26B) so that the SNAP header is DWORD
aligned without adding any pad.
Until 9000, the firmware didn't check the TX_CMD_FLG_MH_PAD bit
but rather checked the length of the MAC header itself and
assumed the entity that enqueued the frame (driver or internal
firmware code) added the pad.
Since the driver inserted the pad even for AMSDU this logic applied.
Note that the padding is a DMA optimization but it's not strictly
needed, so we could pad even if it was not needed.
However, the CSUM hardware introduced for the 9000 devices requires
to not pad AMSDU as it is not needed, and will fail if such a pad
exists.
Due to older FW not checking the padding bit but checking the mac
header size itself - we cannot do this adjustments for older
generations.
Do not align the size if it is an AMSDU and HW checksum is enabled -
which will only happen on 9000 devices and on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Sun, 13 Mar 2016 19:48:35 +0000 (21:48 +0200)]
iwlwifi: pcie: enable interrupts explicitly on resume
When entering suspend the driver calls iwl_disable_interrupts() and
then iwl_pcie_disable_ict().
On resume the driver calls only iwl_pcie_reset_ict() without calling
explicitly to iwl_enable_interrupts().
This mostly works since iwl_pcie_reset_ict is calling to
iwl_enable_interrupts, but it doesn't work when there is no ict_table
in MSIx mode.
The result is that driver tries to resume but fails since it doesn't
get the RX interrupt from FW indicating that d0i3 exit was completed.
Fix it by adding an explicit call to enable interrupts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Mon, 14 Mar 2016 11:11:47 +0000 (13:11 +0200)]
iwlwifi: pcie: fix global table size
My patch resized the pool size, but neglected to resize
the global table, which is obviously wrong since the global
table maps the pool's rxb to vid one to one. This results
in a panic in 9000 devices.
Add a build bug to avoid such a case in the future.
Fixes: 7b5424361ec9 ("iwlwifi: pcie: fine tune number of rxbs") Reported-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Aviya Erenfeld [Thu, 18 Feb 2016 12:09:33 +0000 (14:09 +0200)]
iwlwifi: mvm: add LQM vendor command and notification
LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.
The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Golan Ben-Ami [Tue, 9 Feb 2016 10:57:16 +0000 (12:57 +0200)]
iwlwifi: mvm: support dumping UMAC internal txfifos
In case of FW error, support dumping the UMAC internal txfifos.
To do so, support version 2 of shared memory cfg command, which
contains the sizes of the internal txfifos, and move the command
to the system group.
Matti Gottlieb [Thu, 10 Mar 2016 14:18:26 +0000 (16:18 +0200)]
iwlwifi: mvm: make sure FW contains the right amount of paging sections
Paging contains 3 sections in the fw. The first for the paging separator,
The second for the CSS block, the third with the paging data.
Currently if the driver finds the paging separator, and there is only
section left (CSS), once reading the CSS section, the driver will
attempt to read the paging data and will go out of the arrays bounds.
Make sure that the FW image contains the right amount of sections for
paging.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Matti Gottlieb [Wed, 9 Mar 2016 08:54:10 +0000 (10:54 +0200)]
iwlwifi: mvm: Decrease size of the paging download buffer
Currently the driver has 2 buffers for paging:
1. paging db - this contains all of the pages that were in the FW
image, that the driver stores for the FW. This is allocated for each
block separately (not contiguous).
2. download buffer - we need to provide this empty buffer for the
iwl_sdio_load_fw_chunk function to copy the requested pages to the shared
memory. This is one big buffer of contiguous memory whose size is the
size of all the blocks that the fw paging section can contain.
This download buffer size is too big, and causes the allocation to fail
sometimes. Since the driver allocates memory for each block separately,
it is not possible for the FW to request all of the pages in one request
(the FW gives an address and size, so blocks need to be contiguous for
this to happen), therefore the FW is limited to request only one block.
Decrease the size of the paging download buffer to be the size of a
paging block.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sara Sharon [Wed, 9 Mar 2016 15:38:47 +0000 (17:38 +0200)]
iwlwifi: pcie: clear trans reference on queue stop
Currently when stop flow is performed, there might be transport TX RTPM
references that are not freed in case we unmap a queue that still has
packets not reclaimed. Fix that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Linus Torvalds [Sat, 19 Mar 2016 03:25:49 +0000 (20:25 -0700)]
Merge branch 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"cgroup changes for v4.6-rc1. No userland visible behavior changes in
this pull request. I'll send out a separate pull request for the
addition of cgroup namespace support.
- The biggest change is the revamping of cgroup core task migration
and controller handling logic. There are quite a few places where
controllers and tasks are manipulated. Previously, many of those
places implemented custom operations for each specific use case
assuming specific starting conditions. While this worked, it makes
the code fragile and difficult to follow.
The bulk of this pull request restructures these operations so that
most related operations are performed through common helpers which
implement recursive (subtrees are always processed consistently)
and idempotent (they make cgroup hierarchy converge to the target
state rather than performing operations assuming specific starting
conditions). This makes the code a lot easier to understand,
verify and extend.
- Implicit controller support is added. This is primarily for using
perf_event on the v2 hierarchy so that perf can match cgroup v2
path without requiring the user to do anything special. The kernel
portion of perf_event changes is acked but userland changes are
still pending review.
- cgroup_no_v1= boot parameter added to ease testing cgroup v2 in
certain environments.
- There is a regression introduced during v4.4 devel cycle where
attempts to migrate zombie tasks can mess up internal object
management. This was fixed earlier this week and included in this
pull request w/ stable cc'd.
- Misc non-critical fixes and improvements"
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (44 commits)
cgroup: avoid false positive gcc-6 warning
cgroup: ignore css_sets associated with dead cgroups during migration
Documentation: cgroup v2: Trivial heading correction.
cgroup: implement cgroup_subsys->implicit_on_dfl
cgroup: use css_set->mg_dst_cgrp for the migration target cgroup
cgroup: make cgroup[_taskset]_migrate() take cgroup_root instead of cgroup
cgroup: move migration destination verification out of cgroup_migrate_prepare_dst()
cgroup: fix incorrect destination cgroup in cgroup_update_dfl_csses()
cgroup: Trivial correction to reflect controller.
cgroup: remove stale item in cgroup-v1 document INDEX file.
cgroup: update css iteration in cgroup_update_dfl_csses()
cgroup: allocate 2x cgrp_cset_links when setting up a new root
cgroup: make cgroup_calc_subtree_ss_mask() take @this_ss_mask
cgroup: reimplement rebind_subsystems() using cgroup_apply_control() and friends
cgroup: use cgroup_apply_enable_control() in cgroup creation path
cgroup: combine cgroup_mutex locking and offline css draining
cgroup: factor out cgroup_{apply|finalize}_control() from cgroup_subtree_control_write()
cgroup: introduce cgroup_{save|propagate|restore}_control()
cgroup: make cgroup_drain_offline() and cgroup_apply_control_{disable|enable}() recursive
cgroup: factor out cgroup_apply_control_enable() from cgroup_subtree_control_write()
...
Eric Dumazet [Fri, 18 Mar 2016 00:23:36 +0000 (17:23 -0700)]
bonding: fix bond_get_stats()
bond_get_stats() can be called from rtnetlink (with RTNL held)
or from /proc/net/dev seq handler (with RCU held)
The logic added in commit 5f0c5f73e5ef ("bonding: make global bonding
stats more reliable") kind of assumed only one cpu could run there.
If multiple threads are reading /proc/net/dev, stats can be really
messed up after a while.
A second problem is that some fields are 32bit, so we need to properly
handle the wrap around problem.
Given that RTNL is not always held, we need to use
bond_for_each_slave_rcu().
Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 17 Mar 2016 18:57:06 +0000 (11:57 -0700)]
net: bcmgenet: fix dma api length mismatch
When un-mapping skb->data in __bcmgenet_tx_reclaim(),
we must use the length that was used in original dma_map_single(),
instead of skb->len that might be bigger (includes the frags)
We simply can store skb_len into tx_cb_ptr->dma_len and use it
at unmap time.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 17 Mar 2016 16:49:42 +0000 (18:49 +0200)]
net/mlx4_core: Fix backward compatibility on VFs
Commit 85743f1eb345 ("net/mlx4_core: Set UAR page size to 4KB regardless
of system page size") introduced dependency where old VF drivers without
this fix fail to load if the PF driver runs with this commit.
To resolve this add a module parameter which disables that functionality
by default. If both the PF and VFs are running with a driver with that
commit the administrator may set the module param to true.
The module parameter is called enable_4k_uar.
Fixes: 85743f1eb345 ('net/mlx4_core: Set UAR page size to 4KB ...') Signed-off-by: Eli Cohen <eli@mellanox.com> Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 19 Mar 2016 03:06:46 +0000 (20:06 -0700)]
Merge branch 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- ahci grew runtime power management support so that the controller can
be turned off if no devices are attached.
- sata_via isn't dead yet. It got hotplug support and more refined
workaround for certain WD drives.
- Misc cleanups. There's a merge from for-4.5-fixes to avoid confusing
conflicts in ahci PCI ID table.
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_xgene: dereferencing uninitialized pointer in probe
AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
ata: sata_rcar: Use ARCH_RENESAS
sata_via: Implement hotplug for VT6421
sata_via: Apply WD workaround only when needed on VT6421
ahci: Add runtime PM support for the host controller
ahci: Add functions to manage runtime PM of AHCI ports
ahci: Convert driver to use modern PM hooks
ahci: Cache host controller version
scsi: Drop runtime PM usage count after host is added
scsi: Set request queue runtime PM status back to active on resume
block: Add blk_set_runtime_active()
ata: ahci_mvebu: add support for Armada 3700 variant
libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
libata: support AHCI on OCTEON platform
Linus Torvalds [Sat, 19 Mar 2016 03:05:39 +0000 (20:05 -0700)]
Merge branch 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
"Three trivial workqueue changes"
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Fix comment for work_on_cpu()
sched/core: Get rid of 'cpu' argument in wq_worker_sleeping()
workqueue: Replace usage of init_name with dev_set_name()
Andreas Färber [Wed, 16 Mar 2016 23:23:37 +0000 (00:23 +0100)]
phy: mdio-thunder: Fix some Kconfig typos
Drop two extra occurrences of "on" in option title and help text.
Fixes: 379d7ac7ca31 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Cc: David Daney <david.daney@cavium.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Wed, 16 Mar 2016 22:10:42 +0000 (22:10 +0000)]
lan78xx: add ndo_get_stats64
Add lan78xx_get_stats64 of ndo_get_stats64 to report
all statistics counters including errors from HW statistics.
Read from HW when auto suspend is disabled, use saved counter when
auto suspend is enabled because periodic call to ndo_get_stats64
prevents USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Wed, 16 Mar 2016 22:10:40 +0000 (22:10 +0000)]
lan78xx: handle statistics counter rollover
Update to handle statistics counter rollover.
Check statistics counter periodically and compensate it when
counter value rolls over at max (20 or 32bits).
Simple mechanism adjusts monitoring timer to allow USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 19 Mar 2016 02:26:54 +0000 (19:26 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Sowmini Varadhan [Wed, 16 Mar 2016 18:38:12 +0000 (11:38 -0700)]
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
Add per-net sysctl tunables to set the size of sndbuf and
rcvbuf on the kernel tcp socket.
The tunables are added at /proc/sys/net/rds/tcp/rds_tcp_sndbuf
and /proc/sys/net/rds/tcp/rds_tcp_rcvbuf.
These values must be set before accept() or connect(),
and there may be an arbitrary number of existing rds-tcp
sockets when the tunable is modified. To make sure that all
connections in the netns pick up the same value for the tunable,
we reset existing rds-tcp connections in the netns, so that
they can reconnect with the new parameters.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Wed, 16 Mar 2016 17:26:02 +0000 (18:26 +0100)]
net: smc911x: convert pxa dma to dmaengine
Convert the dma transfers to be dmaengine based, now pxa has a dmaengine
slave driver. This makes this driver a bit more PXA agnostic.
The driver was only compile tested. The risk is quite small as no
current PXA platform I'm aware of is using smc911x driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Wed, 16 Mar 2016 09:59:16 +0000 (09:59 +0000)]
team: remove duplicate set of flag IFF_MULTICAST
Remove unnecessary set of flag IFF_MULTICAST, since ether_setup
already does this.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Wed, 16 Mar 2016 09:59:15 +0000 (09:59 +0000)]
bonding: remove duplicate set of flag IFF_MULTICAST
Remove unnecessary set of flag IFF_MULTICAST, since ether_setup
already does this.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 19 Mar 2016 00:13:31 +0000 (17:13 -0700)]
Merge branch 'for-4.6/drivers' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"This is the block driver pull request for this merge window. It sits
on top of for-4.6/core, that was just sent out.
This contains:
- A set of fixes for lightnvm. One from Alan, fixing an overflow,
and the rest from the usual suspects, Javier and Matias.
- A set of fixes for nbd from Markus and Dan, and a fixup from Arnd
for correct usage of the signed 64-bit divider.
- A set of bug fixes for the Micron mtip32xx, from Asai.
- A fix for the brd discard handling from Bart.
- Update the maintainers entry for cciss, since that hardware has
transferred ownership.
- Three bug fixes for bcache from Eric Wheeler.
- Set of fixes for xen-blk{back,front} from Jan and Konrad.
- Removal of the cpqarray driver. It has been disabled in Kconfig
since 2013, and we were initially scheduled to remove it in 3.15.
- Various updates and fixes for NVMe, with the most important being:
- Removal of the per-device NVMe thread, replacing that with a
watchdog timer instead. From Christoph.
- Exposing the namespace WWID through sysfs, from Keith.
- Set of cleanups from Ming Lin.
- Logging the controller device name instead of the underlying
PCI device name, from Sagi.
- And a bunch of fixes and optimizations from the usual suspects
in this area"
* 'for-4.6/drivers' of git://git.kernel.dk/linux-block: (49 commits)
NVMe: Expose ns wwid through single sysfs entry
drivers:block: cpqarray clean up
brd: Fix discard request processing
cpqarray: remove it from the kernel
cciss: update MAINTAINERS
NVMe: Remove unused sq_head read in completion path
bcache: fix cache_set_flush() NULL pointer dereference on OOM
bcache: cleaned up error handling around register_cache()
bcache: fix race of writeback thread starting before complete initialization
NVMe: Create discard zero quirk white list
nbd: use correct div_s64 helper
mtip32xx: remove unneeded variable in mtip_cmd_timeout()
lightnvm: generalize rrpc ppa calculations
lightnvm: remove struct nvm_dev->total_blocks
lightnvm: rename ->nr_pages to ->nr_sects
lightnvm: update closed list outside of intr context
xen/blback: Fit the important information of the thread in 17 characters
lightnvm: fold get bb tbl when using dual/quad plane mode
lightnvm: fix up nonsensical configure overrun checking
xen-blkback: advertise indirect segment support earlier
...
Linus Torvalds [Fri, 18 Mar 2016 23:43:11 +0000 (16:43 -0700)]
Merge branch 'for-4.6/core' of git://git.kernel.dk/linux-block
Pull core block updates from Jens Axboe:
"Here are the core block changes for this merge window. Not a lot of
exciting stuff going on in this round, most of the changes have been
on the driver side of things. That pull request is coming next. This
pull request contains:
- A set of fixes for chained bio handling from Christoph.
- A tag bounds check for blk-mq from Hannes, ensuring that we don't
do something stupid if a device reports an invalid tag value.
- A set of fixes/updates for the CFQ IO scheduler from Jan Kara.
- A set of blk-mq fixes from Keith, adding support for dynamic
hardware queues, and fixing init of max_dev_sectors for stacking
devices.
- A fix for the dynamic hw context from Ming.
- Enabling of cgroup writeback support on a block device, from
Shaohua"
* 'for-4.6/core' of git://git.kernel.dk/linux-block:
blk-mq: add bounds check on tag-to-rq conversion
block: bio_remaining_done() isn't unlikely
block: cleanup bio_endio
block: factor out chained bio completion
block: don't unecessarily clobber bi_error for chained bios
block-dev: enable writeback cgroup support
blk-mq: Fix NULL pointer updating nr_requests
blk-mq: mark request queue as mq asap
block: Initialize max_dev_sectors to 0
blk-mq: dynamic h/w context count
cfq-iosched: Allow parent cgroup to preempt its child
cfq-iosched: Allow sync noidle workloads to preempt each other
cfq-iosched: Reorder checks in cfq_should_preempt()
cfq-iosched: Don't group_idle if cfqq has big thinktime
Dan Carpenter [Wed, 16 Mar 2016 07:45:10 +0000 (10:45 +0300)]
ethernet: micrel: fix some error codes
There were two issues here:
1) dma_mapping_error() return true/false but we want to return -ENOMEM
2) If dmaengine_prep_slave_sg() failed then "err" wasn't set but
presumably that should be -ENOMEM as well.
I changed the success path to "return 0;" instead of "return ret;" for
clarity.
Fixes: 94fe8c683cea ('ks8842: Support DMA when accessed via timberdale') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Mar 2016 23:38:53 +0000 (19:38 -0400)]
Merge branch 'bpf-misc'
Daniel Borkmann says:
====================
Minor BPF follow-ups
Some minor last follow-ups I still had in my queue. The first one adds
readability support for __sk_buff's tc_classid member, the remaining
two are some minor cleanups. For details please see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 16 Mar 2016 00:42:51 +0000 (01:42 +0100)]
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
eBPF defines this as BPF_TUNLEN_MAX and OVS just uses the hard-coded
value inside struct sw_flow_key. Thus, add and use IP_TUNNEL_OPTS_MAX
for this, which makes the code a bit more generic and allows to remove
BPF_TUNLEN_MAX from eBPF code.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 16 Mar 2016 00:42:50 +0000 (01:42 +0100)]
bpf, dst: add and use dst_tclassid helper
We can just add a small helper dst_tclassid() for retrieving the
dst->tclassid value. It makes the code a bit better in that we can
get rid of the ifdef from filter.c by moving this into the header.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 16 Mar 2016 00:42:49 +0000 (01:42 +0100)]
bpf: make skb->tc_classid also readable
Currently, the tc_classid from eBPF skb context is write-only, but there's
no good reason for tc programs to limit it to write-only. For example,
it can be used to transfer its state via tail calls where the resulting
tc_classid gets filled gradually.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 15 Mar 2016 21:47:14 +0000 (22:47 +0100)]
net: mvneta: bm: clarify dependencies
MVNETA_BM has a dependency on MVNETA, so we can only select the former
if the latter is enabled. However, the code dependency is the reverse:
The mvneta module can call into the mvneta_bm module, so mvneta cannot
be a built-in if mvneta_bm is a module, or we get a link error:
drivers/net/built-in.o: In function `mvneta_remove':
drivers/net/ethernet/marvell/mvneta.c:4211: undefined reference to `mvneta_bm_pool_destroy'
drivers/net/built-in.o: In function `mvneta_bm_update_mtu':
drivers/net/ethernet/marvell/mvneta.c:1034: undefined reference to `mvneta_bm_bufs_free'
This avoids the problem by further clarifying the dependency so that
MVNETA_BM is a silent Kconfig option that gets turned on by the
new MVNETA_BM_ENABLE option. This way both the core HWBM module and
the MVNETA_BM code are always built-in when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management") Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 15 Mar 2016 21:41:22 +0000 (22:41 +0100)]
cls_bpf: reset class and reuse major in da
There are two issues with the current code. First one is that we need
to set res->class to 0 in case we use non-default classid matching.
This is important for the case where cls_bpf was initially set up with
an optional binding to a default class with tcf_bind_filter(), where
the underlying qdisc implements bind_tcf() that fills res->class and
tests for it later on when doing the classification. Convention for
these cases is that after tc_classify() was called, such qdiscs (atm,
drr, qfq, cbq, hfsc, htb) first test class, and if 0, then they lookup
based on classid.
Second, there's a bug with da mode, where res->classid is only assigned
a 16 bit minor, but it needs to expand to the full 32 bit major/minor
combination instead, therefore we need to expand with the bound major.
This is fine as classes belonging to a classful qdisc must share the
same major.
Fixes: 045efa82ff56 ("cls_bpf: introduce integrated actions") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Mar 2016 23:33:05 +0000 (19:33 -0400)]
Merge branch 'ldmvsw'
Aaron Young says:
====================
ldmvsw: Add ldmvsw driver
This series adds a new Logical Domains vSwitch (ldmvsw) driver.
The ldmvsw driver code will live in the drivers/net/ethernet/sun/
directory and will operate on Oracle systems running SPARC Linux in a
Logical Domains environment (typically in the control domain).
The ldmvsw driver is very similar in function to the existing sunvnet
driver. Ldmvsw creates a network interface for each "vsw-port" node
found in the Machine Description (MD) of a service domain. These
nodes correspond to ports on a vswitch created by the logical domains
manager. The created network interface(s) can be used by bridge/vswitch
software (such as the Linux bridge or Open vSwitch) to provide
guest domain(s) with network interconnectivity or connectivity
to a physical network.
Here is a example diagram of ldmvsw driver usage in a logical
domain environment to provide a guest domain with network connectivity
to a physical NIC on the service domain:
As stated, the sunvnet and ldmvsw drivers are _very_ similar in function.
They both create network interface(s) to receive/transmit network
traffic across LDC network channel(s). Since the driver is so similar
in function to sunvnet, the approach will be as follows to integrate
the driver and take advantage of common code:
Patch #1: Split sunvnet.c driver into sunvnet.c and sunvnet_common.c
Patch #2: Modify the sunvnet_common code and data structures to be compatible
with both the sunvnet and ldmvsw drivers.
Patch #3: Add the new ldmvsw.c driver code
Patch #4: Checkpatch cleanup of the sunvnet/sunvnet_common code.
NOTE - Patch#1 renames a file (sunvnet.h -> sunvnet_common.h). When generating
the patches (using git format-patch), I had to use the --no-renames option
otherwise patch#1 would NOT apply using 'patch -p1' - which as I
understand is a requirement for patch acceptance. I wasn't sure if this
is proper thing to do. Please advise if not. Thanks.
v2 changes:
* change all EXPORT_SYMBOL declarations to EXPORT_SYMBOL_GPL
* remove inline attribute for external function port_is_up_common()
* Give all exported/global funcs in sunvnet_common.c a 'sunvnet_' prefix
to avoid kernel global namespace pollution/collisions
* ldmvsw.c: Order local variable declarations from longest to shortest line
* ldmvsw.c: register the netdevice after all supporting state is ready/setup.
NOTE: The consensus at Oracle is that the following functions
must be done AFTER register_netdev() - this is the same
ordering currently used in the sunvnet driver:
1. sunvnet_port_add_txq_common() - needs registered netdev
2. napi_enable() - requires registered netdev
3. vio_port_up() - as soon as this function is called
LDC handshake messages will come in
which must be handled by the napi code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Young [Tue, 15 Mar 2016 18:35:39 +0000 (11:35 -0700)]
ldmvsw: Add ldmvsw.c driver code
Add ldmvsw.c driver
Details:
The ldmvsw driver very closely follows the sunvnet.c code and makes
use of the sunvnet_common.c code for core functionality.
A significant difference between sunvnet and ldmvsw driver is
sunvnet creates a network interface for each vnet-port *parent*
node in the MD while the ldmvsw driver creates a network interface
for every vsw-port node in the Machine Description (MD).
Therefore the netdev_priv() for sunvnet is a vnet structure while
the netdev_priv() for ldmvsw is a vnet_port structure.
Vnet_port structures allocated by ldmvsw have the vsw bit set.
When finding the net_device associated with a port, the common code keys
off this bit to use either the net_device found in the vnet_port or the
net_device in the vnet structure (see the VNET_PORT_TO_NET_DEVICE() macro in
sunvnet_common.h). This scheme allows the common code to work with
both drivers with minimal changes.
Similar to Xen, network interfaces created by the ldmvsw driver will always
have a HW Addr (i.e. mac address) of FE:FF:FF:FF:FF:FF and each will be
assigned the devname "vif<cfg_handle>.<port_id>" - where <cfg_handle> and
<port_id> are a unique handle/port pair assigned to the associated
vsw-port node in the MD.
Signed-off-by: Aaron Young <aaron.young@oracle.com> Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com> Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Young [Tue, 15 Mar 2016 18:35:38 +0000 (11:35 -0700)]
ldmvsw: Make sunvnet_common compatible with ldmvsw
Modify sunvnet common code and data structures to be compatible
with both sunvnet and ldmvsw drivers.
Details:
Sunvnet operates on "vnet-port" nodes which appear in the Machine
Description (MD) in a guest domain. Ldmvsw operates on "vsw-port"
nodes which appear in the MD of a service domain.
A difference between the sunvnet driver and the ldmvsw driver is
the sunvnet driver creates a network interface (i.e. a struct net_device)
for every vnet-port *parent* "network" node. Several vnet-ports may appear
under this common parent network node - each corresponding to a common parent
network interface. Conversely, since bridge/vswitch software will need
to interface with every vsw-port in a system, the ldmvsw driver creates
a network interface (i.e. a struct net_device) for every vsw-port - not
every parent node as with sunvnet. This difference required some special
handling in the common code as explained below.
There are 2 key data structures used by the sunvnet and ldmvsw drivers
(which are now found in sunvnet_common.h):
1. struct vnet_port
This structure represents a vnet-port node in sunvnet and a vsw-port
in the ldmvsw driver.
2. struct vnet
This structure represents a parent "network" node in sunvnet and a parent
"virtual-network-switch" node in ldmvsw.
Since the sunvnet driver allocates a net_device for every parent "network"
node, a net_device member appears in the struct vnet. Since the ldmvsw
driver allocates a net_device for every port, a net_device member was
added to the vnet_port. The common code distinguishes which structure
net_device member to use by checking a 'vsw' bit that was added to the
vnet_port structure. See the VNET_PORT_TO_NET_DEVICE() marco in
sunvnet_common.h.
The netdev_priv() in sunvnet is allocated as a vnet. The netdev_priv()
in ldmvsw is a vnet_port. Therefore, any place in the common code
where a netdev_priv() call was made, a wrapper function was implemented
in each driver to first get the vnet and/or vnet_port (in a driver
specific way) and pass them as newly added parameters to the common
functions (see wrapper funcs: vnet_set_rx_mode() and vnet_poll_controller()).
Since these wrapper functions call __tx_port_find(), __tx_port_find() was
moved from the common code back into sunvnet.c. Note - ldmvsw.c does not
require this function.
These changes also required that port_is_up() be made
into a common function and thus it was given a _common suffix and
exported like the other common functions.
A wrapper function was also added for vnet_start_xmit_common() to pass a
driver-specific function arg to return the port associated with a given
struct sk_buff and struct net_device. This was required because
vnet_start_xmit_common() grabs a lock prior to getting the associated
port. Using a function pointer arg allowed the code to work unchanged
without risking changes to the non-trivial locking logic in
vnet_start_xmit_common().
Signed-off-by: Aaron Young <aaron.young@oracle.com> Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com> Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Young [Tue, 15 Mar 2016 18:35:37 +0000 (11:35 -0700)]
ldmvsw: Split sunvnet driver into common code
Split sunvnet.c into sunvnet.c and sunvnet_common.c.
Details:
Since the sunvnet and ldmvsw drivers will both use common sunvnet code,
move the functions (and support functions) anticipated to be common code
from sunvnet.c to sunvnet_common.c. Similarly, sunvnet.h was renamed to
sunvnet_common.h. The sunvnet_common.c code will be compiled into the
kernel and act as a library of functions that are linked by either
(or both) drivers when loaded.
Function names for external functions in sunvnet_common.c (to be
called by both the sunvnet and ldmvsw drivers) were tagged with a "_common"
suffix to clearly designate them as common functions.
No functional changes as of yet... just moved code verbatim to the new
sunvnet_common.c/h files.
Makefile/Kconfig support added to build sunvnet_common.c file. The code
is included in the kernel if SUN_LDOMS is defined/selected.
NOTE - per the SubmittingPatches documentation, since the code was just
moved from one file another, the code was NOT checkpatch'd in this commit
to aid in review.
Signed-off-by: Aaron Young <aaron.young@oracle.com> Signed-off-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com> Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reviewed-by: Alexandre Chartre <Alexandre.Chartre@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 18 Mar 2016 23:19:15 +0000 (16:19 -0700)]
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a USB fix for the reported issue with commit 69bec7259853
("USB: core: let USB device know device node") as well as some other
issues that have been reported so far with this merge window"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: uas: Reduce can_queue to MAX_CMNDS
USB: cdc-acm: more sanity checking
USB: usb_driver_claim_interface: add sanity checking
usb/core: usb_alloc_dev(): fix setting of ->portnum
USB: iowarrior: fix oops with malicious USB descriptors
Yuval Mintz [Tue, 15 Mar 2016 17:52:04 +0000 (19:52 +0200)]
bnx2x: Prevent false warning for lack of FC NPIV
Not all adapters have FC-NPIV configured. If bnx2fc is used with such an
adapter, driver would read irrelevant data from the the nvram and log
"FC-NPIV table with bad length..." In system logs.
Simply accept that reading '0' as the feature offset in nvram indicates
the feature isn't there and return.
Reported-by: Andrew Patterson <andrew.patterson@hpe.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Kaneko [Tue, 15 Mar 2016 15:52:16 +0000 (00:52 +0900)]
ravb: fix result value overwrite
The result value is overwritten by a return value of
ravb_ptp_interrupt().
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Tue, 15 Mar 2016 11:13:45 +0000 (07:13 -0400)]
qlge: Fix receive packets drop.
When running small packets [length < 256 bytes] traffic, packets were
being dropped due to invalid data in those packets which were
delivered by the driver upto the stack. Using pci_dma_sync_single_for_cpu
ensures copying latest and updated data into skb from the receive buffer.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Reid [Tue, 15 Mar 2016 07:34:33 +0000 (15:34 +0800)]
net: stmmac: Don't search for phys if mdio node is defined.
If a dt mdio entry has been added least assume that we wont
search for phys attached. The DT and of_mdiobus_register already do
this. This stops DSA phys being found and phys created for them, as
this is handled by the DSA driver.
Signed-off-by: Phil Reid <preid@electromag.com.au> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 15 Mar 2016 07:19:04 +0000 (10:19 +0300)]
mediatek: unlock on error in mtk_tx_map()
There was a missing unlock on the error path.
Fixes: 656e705243fd ('net-next: mediatek: add support for MT7623 ethernet') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: John Crispin <blogic@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 15 Mar 2016 07:18:49 +0000 (10:18 +0300)]
mediatek: checking for IS_ERR() instead of NULL
of_phy_connect() returns NULL on error, it never returns error pointers.
Fixes: 656e705243fd ('net-next: mediatek: add support for MT7623 ethernet') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: John Crispin <blogic@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 15 Mar 2016 03:00:35 +0000 (12:00 +0900)]
openvswitch: allow output of MPLS packets on tunnel vports
Currently output of MPLS packets on tunnel vports is not allowed by Open
vSwitch. This is because historically encapsulation was done in such a way
that the inner_protocol field of the skb needed to hold the inner protocol
for both MPLS and tunnel encapsulation in order for GSO segmentation to be
performed correctly.
Since b2acd1dc3949 ("openvswitch: Use regular GRE net_device instead of
vport") Open vSwitch makes use of lwt to output to tunnel netdevs which
perform encapsulation. As no drivers expose support for MPLS offloads this
means that GSO packets are segmented in software by validate_xmit_skb(),
which is called from __dev_queue_xmit(), before tunnel encapsulation occurs.
This means that the inner protocol of MPLS is no longer needed by the time
encapsulation occurs and the contention on the inner_protocol field of the
skb no longer occurs.
Thus it is now safe to output MPLS to tunnel vports.
Signed-off-by: Simon Horman <simon.horman@netronome.com> Reviewed-by: Jesse Gross <jesse@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 18 Mar 2016 17:21:04 +0000 (10:21 -0700)]
Merge tag 'for-linus-4.6' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Just some minor fixes, nothing big"
* tag 'for-linus-4.6' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: do not probe ACPI devices if si_tryacpi is unset
ipmi_si: Avoid a wrong long timeout on transaction done
ipmi_si: Fix module parameter doc names
ipmi_ssif: Fix logic around alert handling
Linus Torvalds [Fri, 18 Mar 2016 17:15:11 +0000 (10:15 -0700)]
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Linus Torvalds [Fri, 18 Mar 2016 17:05:46 +0000 (10:05 -0700)]
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
Linus Torvalds [Fri, 18 Mar 2016 16:39:22 +0000 (09:39 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.6 merge window patches.
This is the first of two pull requests. It is the smaller request,
but touches for more different things (this is everything but what is
in or going into staging). The pull request for the code in
staging/rdma is on hold until after we decide what to do on the
write/writev API issue and may be partially deferred until 4.7 as a
result.
Summary:
- cxgb4 updates
- nes updates
- unification of iwarp portmapper code to core
- add drain_cq API
- various ib_core updates
- minor ipoib updates
- minor mlx4 updates
- more significant mlx5 updates (including a minor merge conflict
with net-next tree...merge is simple to resolve and Stephen's
resolution was confirmed by Mellanox)
- trivial net/9p rdma conversion
- ocrdma RoCEv2 update
- srpt updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (85 commits)
iwpm: crash fix for large connections test
iw_cxgb3: support for iWARP port mapping
iw_cxgb4: remove port mapper related code
iw_nes: remove port mapper related code
iwcm: common code for port mapper
net/9p: convert to new CQ API
IB/mlx5: Add support for don't trap rules
net/mlx5_core: Introduce forward to next priority action
net/mlx5_core: Create anchor of last flow table
iser: Accept arbitrary sg lists mapping if the device supports it
mlx5: Add arbitrary sg list support
IB/core: Add arbitrary sg_list support
IB/mlx5: Expose correct max_fast_reg_page_list_len
IB/mlx5: Make coding style more consistent
IB/mlx5: Convert UMR CQ to new CQ API
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Skip using unneeded intermediate variable
IB/ocrdma: Delete unnecessary variable initialisations in 11 functions
IB/core: Documentation fix in the MAD header file
IB/core: trivial prink cleanup.
...
Hans de Goede [Mon, 7 Mar 2016 19:11:52 +0000 (20:11 +0100)]
USB: uas: Reduce can_queue to MAX_CMNDS
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Cc: stable@vger.kernel.org Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Tue, 15 Mar 2016 09:14:04 +0000 (10:14 +0100)]
USB: cdc-acm: more sanity checking
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by not overwriting the port1 argument in usb_alloc_dev(), but
storing the raw port number as required by OF in an additional variable,
raw_port.
Fixes: 69bec7259853 ("USB: core: let USB device know device node") Signed-off-by: Nicolai Stange <nicstange@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josh Boyer [Mon, 14 Mar 2016 14:42:38 +0000 (10:42 -0400)]
USB: iowarrior: fix oops with malicious USB descriptors
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Joe Lawrence [Thu, 18 Feb 2016 21:02:54 +0000 (16:02 -0500)]
ipmi: do not probe ACPI devices if si_tryacpi is unset
Extend the tryacpi module parameter to turn off acpi_ipmi_probe such
that hard-coded options (type, ports, address, etc.) have complete
control over the smi_info data structures setup by the driver.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by: Corey Minyard <cminyard@mvista.com>
Corey Minyard [Mon, 25 Jan 2016 22:11:20 +0000 (16:11 -0600)]
ipmi_si: Avoid a wrong long timeout on transaction done
Under some circumstances, the IPMI state machine could return
a call without delay option but the driver would still do a long
delay because the result wasn't checked. Instead of calling
the state machine after transaction done, just go back to the
top of the processing to start over.
Linus Torvalds [Fri, 18 Mar 2016 05:13:41 +0000 (22:13 -0700)]
Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 4.6-rc1.
Lots of little things here, over 1600 patches or so. Notable is all
of the good Lustre work happening, those developers have finally woken
up and are cleaning up their code greatly. The Outreachy intern
application process is also happening, which brought in another 400 or
so patches. Full details are in the very long shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
staging: lustre: fix aligments in lnet selftest
staging: lustre: report minimum of two buffers for LNet selftest load test
staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
staging: lustre: filter remaining extra spacing for lnet selftest
staging: lustre: remove extra spacing when setting variable for lnet selftest
staging: lustre: remove extra spacing of variable declartions for lnet selftest
staging: lustre: fix spacing issues checkpatch reported in lnet selftest
staging: lustre: remove returns in void function for lnet selftest
staging: lustre: fix bogus lst errors for lnet selftest
staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
staging: android: ion: fix up file mode
staging: ion: debugfs invalid gfp mask
staging: rts5208: Replace pci_enable_device with pcim_enable_device
Staging: ieee80211: Place constant on right side of the test.
staging: speakup: Replace del_timer with del_timer_sync
staging: lowmemorykiller: fix 2 checks that checkpatch complained
staging: mt29f_spinand: Drop void pointer cast
staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
...
Linus Torvalds [Fri, 18 Mar 2016 04:51:52 +0000 (21:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"The most notable item is addition of support for Synaptics RMI4
protocol which is native protocol for all current Synaptics devices
(touchscreens, touchpads). In later releases we'll switch devices
using HID and PS/2 protocol emulation to RMI4.
You will also get:
- BYD PS/2 touchpad protocol support for psmouse
- MELFAS MIP4 Touchscreen driver
- rotary encoder was moved away from legacy platform data and to
generic device properties API, devm_* API, and can now handle
encoders using more than 2 GPIOs
- Cypress touchpad driver was switched to devm_* API and device
properties
- other assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
ARM: pxa/raumfeld: use PROPERTY_ENTRY_INTEGER to define props
Input: synaptics-rmi4 - using logical instead of bitwise AND
Input: powermate - fix oops with malicious USB descriptors
Input: snvs_pwrkey - fix returned value check of syscon_regmap_lookup_by_phandle()
MAINTAINERS: add devicetree bindings to Input Drivers section
Input: synaptics-rmi4 - add device tree support to the SPI transport driver
Input: synaptics-rmi4 - add SPI transport driver
Input: synaptics-rmi4 - add support for F30
Input: synaptics-rmi4 - add support for F12
Input: synaptics-rmi4 - add device tree support for 2d sensors and F11
Input: synaptics-rmi4 - add support for 2D sensors and F11
Input: synaptics-rmi4 - add device tree support for RMI4 I2C devices
Input: synaptics-rmi4 - add I2C transport driver
Input: synaptics-rmi4 - add support for Synaptics RMI4 devices
Input: ad7879 - add device tree support
Input: ad7879 - fix default x/y axis assignment
Input: ad7879 - move header to platform_data directory
Input: ts4800 - add hardware dependency
Input: cyapa - fix for losing events during device power transitions
Input: sh_keysc - remove dependency on SUPERH
...
Linus Torvalds [Fri, 18 Mar 2016 04:46:32 +0000 (21:46 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching
Pull livepatching update from Jiri Kosina:
- cleanup of module notifiers; this depends on a module.c cleanup which
has been acked by Rusty; from Jessica Yu
- small assorted fixes and MAINTAINERS update
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch/module: remove livepatch module notifier
modules: split part of complete_formation() into prepare_coming_module()
livepatch: Update maintainers
livepatch: Fix the error message about unresolvable ambiguity
klp: remove CONFIG_LIVEPATCH dependency from klp headers
klp: remove superfluous errors in asm/livepatch.h
Linus Torvalds [Fri, 18 Mar 2016 04:38:27 +0000 (21:38 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk