Phonet: Implement Pipe Controller to support Nokia Slim Modems
Phonet stack assumes the presence of Pipe Controller, either in Modem or
on Application Processing Engine user-space for the Pipe data.
Nokia Slim Modems like WG2.5 used in ST-Ericsson U8500 platform do not
implement Pipe controller in them.
This patch adds Pipe Controller implemenation to Phonet stack to support
Pipe data over Phonet stack for Nokia Slim Modems.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 24 Sep 2010 09:55:52 +0000 (09:55 +0000)]
ipv6: add a missing unregister_pernet_subsys call
Clean up a missing exit path in the ipv6 module init routines. In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure. But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations. This patch cleans up both the failed load path and
the unload path. Tested by myself with good results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/net/addrconf.h | 1 +
net/ipv6/addrconf.c | 11 ++++++++---
net/ipv6/addrlabel.c | 5 +++++
3 files changed, 14 insertions(+), 3 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Sep 2010 21:46:03 +0000 (21:46 +0000)]
net: fix rcu use in ip_route_output_slow
__in_dev_get_rtnl(dev_out) is called while RTNL is not held, thus
triggers a lockdep fault.
At this point, we only perform a raw test of dev_out->ip_ptr being NULL,
we dont need to make sure ip_ptr cant changed right after.
We can use rcu_dereference_raw() for this.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Sep 2010 17:26:35 +0000 (17:26 +0000)]
rps: allocate rx queues in register_netdevice only
Instead of having two places were we allocate dev->_rx, introduce
netif_alloc_rx_queues() helper and call it only from
register_netdevice(), not from alloc_netdev_mq()
Goal is to let drivers change dev->num_rx_queues after allocating netdev
and before registering it.
This also removes a lot of ifdefs in net/core/dev.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 27 Sep 2010 01:53:07 +0000 (18:53 -0700)]
net: update SOCK_MIN_RCVBUF
SOCK_MIN_RCVBUF current value is 256 bytes
It doesnt permit to receive the smallest possible frame, considering
socket sk_rmem_alloc/sk_rcvbuf account skb truesizes. On 64bit arches,
sizeof(struct sk_buff) is 240 bytes. Add the typical 64 bytes of
headroom, and we go over the limit.
With old kernels and 32bit arches, we were under the limit, if netdriver
was doing copybreak.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Sep 2010 05:06:54 +0000 (05:06 +0000)]
net: skb_frag_t can be smaller on small arches
On 32bit arches, if PAGE_SIZE is smaller than 65536, we can use 16bit
offset and size fields. This patch saves 72 bytes per skb on i386, or
128 bytes after rounding.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Mikko Vinni <mmvinni@yahoo.com> Tested-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Karl Hiramoto <karl@hiramoto.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Sat, 25 Sep 2010 10:39:17 +0000 (10:39 +0000)]
de2104x: fix TP link detection
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Fri, 24 Sep 2010 23:57:02 +0000 (23:57 +0000)]
de2104x: fix power management
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Thu, 23 Sep 2010 12:46:25 +0000 (12:46 +0000)]
ixgbevf: Refactor ring parameter re-size
The function to resize the Tx/Rx rings had the potential to
dereference a NULL pointer and the code would attempt to resize
the Tx ring even if the Rx ring allocation had failed. This
would cause some confusion in the return code semantics. Fixed
up to just unwind the allocations if any of them fail and return
an error.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Thu, 23 Sep 2010 10:59:18 +0000 (10:59 +0000)]
de2104x: disable autonegotiation on broken hardware
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Sep 2010 12:43:39 +0000 (12:43 +0000)]
net: fix a lockdep splat
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 20 Sep 2010 20:16:27 +0000 (20:16 +0000)]
ip: take care of last fragment in ip_append_data
While investigating a bit, I found ip_fragment() slow path was taken
because ip_append_data() provides following layout for a send(MTU +
N*(MTU - 20)) syscall :
- one skb with 1500 (mtu) bytes
- N fragments of 1480 (mtu-20) bytes (before adding IP header)
last fragment gets 17 bytes of trail data because of following bit:
if (datalen == length + fraggap)
alloclen += rt->dst.trailer_len;
Then esp4 adds 16 bytes of data (while trailer_len is 17... hmm...
another bug ?)
In ip_fragment(), we notice last fragment is too big (1496 + 20) > mtu,
so we take slow path, building another skb chain.
In order to avoid taking slow path, we should correct ip_append_data()
to make sure last fragment has real trail space, under mtu...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
E1000 can benefit from calling the GRO receive functions.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers in general have an issue where timers fired
by mod_timer or work threads with schedule_work are running
outside of the rtnl_lock.
With no other lock protection these routines are vulnerable
to races with driver unload or reset paths.
The longer term solution to this might be a redesign with
safer locks being taken in the driver to guarantee no
reentrance, but for now a safe and effective fix is
to take the rtnl_lock in these routines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
E1000 is using several timers that in a follow on patch
will need to acquire the rtnl_lock in order to be safe.
This patch moves the timer bodies into work queues which
will allow the next patch to add rtnl_lock.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Wed, 22 Sep 2010 17:57:58 +0000 (17:57 +0000)]
e1000/e1000e/igb/ixgb/ixgbe: set NETIF_F_HIGHDMA for VLAN feature flags
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel(r) DH89xxCC series. The new
device will be using Intel(r) i347-AT4 and Marvell(r) M88E1322 and
M88E1112 PHYs. Support for these devices has also been added here.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 22 Sep 2010 17:56:20 +0000 (17:56 +0000)]
igb: clear VF_PROMISC bits instead of setting all other bits
This change corrects an issue in which we were setting all flag bits except
for promisc instead of clearing the promisc bits due to the incorrect use
of an |= instead of an &=.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:17:01 +0000 (17:17 +0000)]
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:16:18 +0000 (17:16 +0000)]
e1000e: 82579 unaccounted missed packets
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
CC: stable@kernel.org Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:15:33 +0000 (17:15 +0000)]
e1000e: 82579 SMBus address and LEDs incorrect after device reset
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:15:08 +0000 (17:15 +0000)]
e1000e: 82577/8/9 issues with device in Sx
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1: zero out CMB and SBM in atl1_free_ring_resources
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Move "struct net" declaration inside the __KERNEL__ macro guard
This patch reduces namespace pollution by moving the "struct net" declaration
out of the userspace-facing portion of linux/netlink.h. It has no impact on
the kernel.
(This came up because we have several C++ applications which use "net" as a
namespace name.)
Signed-off-by: Ollie Wild <aaw@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Olsa [Tue, 21 Sep 2010 21:17:34 +0000 (21:17 +0000)]
netfilter: nf_conntrack_defrag: check socket type before touching nodefrag flag
we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.
For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 21:17:32 +0000 (21:17 +0000)]
netfilter: fix a race in nf_ct_ext_create()
As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.
Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: fix ipt_REJECT TCP RST routing for indev == outdev
ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.
__mkroute_input functions has this check:
1998 if (skb->protocol != htons(ETH_P_IP)) {
1999 /* Not IP (i.e. ARP). Do not create route, if it is
2000 * invalid for proxy arp. DNAT routes are always valid.
2001 *
2002 * Proxy arp feature have been extended to allow, ARP
2003 * replies back to the same interface, to support
2004 * Private VLAN switch technologies. See arp.c.
2005 */
2006 if (out_dev == in_dev &&
2007 IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008 err = -EINVAL;
2009 goto cleanup;
2010 }
2011 }
This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.
This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 21 Sep 2010 21:17:30 +0000 (21:17 +0000)]
netfilter: nf_ct_sip: default to NF_ACCEPT in sip_help_tcp()
I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.
net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Simon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 21:17:29 +0000 (21:17 +0000)]
netfilter: tproxy: nf_tproxy_assign_sock() can handle tw sockets
transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Mon, 20 Sep 2010 20:40:24 +0000 (20:40 +0000)]
drivers: atm: use native kernel's hex_to_bin() func
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Chas Williams <chas@cmf.nrl.navy.mil> Cc: linux-atm-general@lists.sourceforge.net Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2010 23:12:11 +0000 (16:12 -0700)]
ethtool: Fix build due to lack of ethtool.h include.
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2010 23:11:06 +0000 (16:11 -0700)]
sfc: Fix build due to lack of vmalloc.h include.
drivers/net/sfc/filter.c: In function ‘efx_probe_filters’:
drivers/net/sfc/filter.c:422: error: implicit declaration of function ‘vmalloc’
drivers/net/sfc/filter.c:422: warning: assignment makes pointer from integer without a cast
drivers/net/sfc/filter.c: In function ‘efx_remove_filters’:
drivers/net/sfc/filter.c:442: error: implicit declaration of function ‘vfree’
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 08:47:45 +0000 (08:47 +0000)]
ip: fix truesize mismatch in ip fragmentation
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 2b85a34e911 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit b2722b1c3a893e
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com> Tested-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Mon, 20 Sep 2010 11:45:38 +0000 (13:45 +0200)]
ath9k: clean up / fix aggregation session flush
The tid aggregation cleanup is a bit fragile, as it discards failed
subframes in some places, and retransmits them in others. This could
block the cleanup of an existing aggregation session, if a retransmission
for a tid is issued, yet the tid is never scheduled again because of
the cleanup state.
Fix this by getting rid of as many subframes as possible, as early
as possible, and immediately transmitting pending subframes as regular
HT frames instead of waiting for the cleanup to complete.
Drop all pending subframes while keeping track of the Block ACK window
during aggregate tx completion to prevent sending out stale subframes,
which could confuse the receiver side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 20 Sep 2010 17:35:28 +0000 (19:35 +0200)]
ath9k: fix an aggregation start related race condition
A new aggregation session start can be issued by mac80211, even when the
cleanup of the previous session has not completed yet. Since the data structure
for the session is not recreated, this could corrupt the block ack window
and lock up the aggregation session. Fix this by delaying the new session
until the old one has been cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 20 Sep 2010 11:45:36 +0000 (13:45 +0200)]
ath9k: clean up block ack window handling
There's no reason to keep pointers to pending tx buffers around, if they're
only used to keep track of which frames are still pending. Use a bitfield
instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: reinit phy after HT settings have changed
The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.
And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since carl9170 gained support to read the noisefloor,
the reported noisefloor level was pretty poor.
Initially I assumed that something was wrong in the PHY
setup and it would be impossible to fix without any
guidances. But this was not the case. In fact the nf
readings were correct and the thing that was broken
was the "simple" sign extension code!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:12 +0000 (11:37 +0900)]
ath5k: Simplify cw_min/max and AIFS configuration
Get rid of overly complicated cw_min/max and AIFS configuration:
* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
without further checks or computation in ath5k_hw_reset_tx_queue().
* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
don't support XR or B channels. That way we can also remove
AR5K_TXQ_USEDEFAULT and the confusing logic around it.
* Update data types: AIFS is u8, CW's are u16.
* Remove now unneeded variables in ath5k_hw.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:07 +0000 (11:37 +0900)]
ath5k: Keep last descriptor in queue
If we return a TX descriptor to the pool of available descriptors, while a
queues TXDP still points to it we could potentially run into all sorts of
troube.
It has been suggested that there is hardware which can set the descriptors
done bit before it reads ds_link and moves on to the next descriptor. While the
documentation says this is not true for newer chipsets (the descriptor contents
are copied to some internal memory), we don't know about older hardware.
To be safe, we always keep the last descriptor in the queue, and avoid dangling
TXDP pointers. Unfortunately this does not fully resolve the problem - queues
still get stuck!
This is similar to what ath9k does.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:36:56 +0000 (11:36 +0900)]
ath5k: Add watchdog for stuck TX queues
Since we do not know any better solution to the problem that TX queues can get
stuck, this adds a timer-based watchdog, which will check for stuck queues and
reset the hardware if necessary.
projects / linux-beck.git / log