Nicolin Chen [Mon, 5 Aug 2013 08:26:16 +0000 (16:26 +0800)]
ENGR00273838-8 ASoC: WM8962: Let codec driver enable/disable its MCLK
WM8962 needs its MCLK when powerup -- wm8962_resume(). Thus it's better
to control the MCLK in codec driver. Thus remove the clock enable in
machine dirver accordingly.
Acked-by: Wang Shengjiu <b02247@freescale.com> Signed-off-by: Nicolin Chen <b42378@freescale.com>
Nicolin Chen [Mon, 5 Aug 2013 07:34:05 +0000 (15:34 +0800)]
ENGR00273838-7 ASoC: fsl: Use hw_params() and hw_free() to set FLL
We followed community way by using set_bias() to set FLL of WM8962.
But this can't meet our requirement: aplay -Dhw: 16khz.wav 24khz.wav.
Thus use hw_params() and hw_free() instead.
Acked-by: Wang Shengjiu <b02247@freescale.com> Signed-off-by: Nicolin Chen <b42378@freescale.com>
Nicolin Chen [Mon, 5 Aug 2013 06:50:50 +0000 (14:50 +0800)]
ENGR00273838-6 arm: dtsi: imx6qdl: Remove fifo-depth for ssi
Remove fifo-depth for ssi and let the driver use the default value 8.
Doing this modification is because 15 fifo-depth, an odd number, is
not working perfectly with ssi dual-fifo mode by setting sdma water
mark to 13 (result from 15 - 2).
Acked-by: Wang Shengjiu <b02247@freescale.com> Signed-off-by: Nicolin Chen <b42378@freescale.com>
net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Li [Thu, 25 Jul 2013 06:05:53 +0000 (14:05 +0800)]
net: fec: workaround stop tx during errata ERR006358
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fec: Fix multicast list setup in fec_restart().
Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tushar Behera [Mon, 10 Jun 2013 11:35:05 +0000 (17:05 +0530)]
net: fec: Convert to use devm_ioremap_resource
Commit 75096579c3ac ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org> CC: netdev@vger.kernel.org CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Roland Stigge <stigge@antcom.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Tested-by: Roland Stigge <stigge@antcom.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Mon, 27 May 2013 03:48:29 +0000 (03:48 +0000)]
fec: Place the phy regulator in the private structure
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Mon, 20 May 2013 03:06:17 +0000 (03:06 +0000)]
fec: Let device core handle pinctrl
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the equation to calculate ramp_delay.
Below equations are equivalent:
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 50000 / (4 * ramp_delay);
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 12500 / ramp_delay;
So we don't need to read BIT6 of rdev->desc->vsel_reg for applying different
equations.
Also use rdev->desc->vsel_reg instead of run-time calculate register address.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Robin Gong <b38343@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Axel Lin [Tue, 30 Jul 2013 02:46:28 +0000 (10:46 +0800)]
regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
Current code adjust min_uV and uV_step but missed adjusting the n_voltages
setting.
When BIT6 is clear:
n_voltages = (1975000 - 400000) / 25000 + 1 = 64
When BIT6 is set:
n_voltages = (3300000 - 800000) / 50000 + 1 = 51
The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
When using regulator_list_voltage_linear, the n_voltages does matter here
because wrong n_voltages setting make the equation return wrong result.
e.g. if selector is 63, regulator_list_voltage_linear returns
800000 + (50000 * 63) = 4000000
It should return -EINVAL if the selector is in the range of 51 ~ 63.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Axel Lin [Mon, 29 Jul 2013 04:08:01 +0000 (12:08 +0800)]
regulator: pfuze100: REGULATOR_PFUZE100 needs to select REGMAP_I2C
This fixes below build errors:
CC [M] drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:342:21: error: variable 'pfuze_regmap_config' has initializer but incomplete type
drivers/regulator/pfuze100-regulator.c:343:2: error: unknown field 'reg_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:343:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:343:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: error: unknown field 'val_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:344:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: error: unknown field 'max_register' specified in initializer
drivers/regulator/pfuze100-regulator.c:345:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: error: unknown field 'cache_type' specified in initializer
drivers/regulator/pfuze100-regulator.c:346:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c: In function 'pfuze100_regulator_probe':
drivers/regulator/pfuze100-regulator.c:370:2: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
drivers/regulator/pfuze100-regulator.c:370:21: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[2]: *** [drivers/regulator/pfuze100-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Robin Gong <b38343@freescale.com> Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: wm8962: Do not call configure_bclk() inside wm8962_set_dai_sysclk()
Currently after playing any audio file, we get the following error message:
$ aplay clarinet.wav
Playing WAVE 'clarinet.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
$ wm8962 0-001a: Unsupported sysclk ratio 544
This error message appears about 5 seconds after the audio playback has
finished.
Quoting Mark Brown [1]:
"The issue here is triggered by the machine
switching from the FLL to direct MCLK usage where the MCLK isn't
generating a useful ratio.
I suspect we should just kill the configure_bclk() in set_sysclk(), that
one isn't safe as we can't reconfigure a live SYSCLK and it's probably
the one that generates your warnings."
Confirmed that the "Unsupported sysclk ratio" error message comes from
wm8962_set_dai_sysclk(), so get rid of wm8962_configure_bclk() inside this
function.
Anson Huang [Mon, 5 Aug 2013 15:42:00 +0000 (11:42 -0400)]
ENGR00273512-2 ARM: imx: Change GPT clock source to OSC
GPT clock is system clock source, need to avoid freq varying,
as system bus clock(ipg) may be changed, for i.mx6 series SOCs,
all of them except i.mx6q TO1.0 support sourcing GPT clk from
OSC directly, so switch gpt clock to OSC if the SOCs support
this feature, as OSC freq is constant.
ASoC: spdif: Add S20_3LE and S24_LE support for dummy codec drivers
Generally, S/PDIF supports 20bit and optional 24bit samples. Thus add these
two formats for the dummy codec drivers.
If one S/PDIF controller has its own limitation, its CPU DAI driver should
set the supported format by its own circumstance, since the soc-pcm driver
will use the intersection of cpu_dai's formats and codec_dai's formats.
Signed-off-by: Nicolin Chen <b42378@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Liu Ying [Thu, 1 Aug 2013 08:32:11 +0000 (16:32 +0800)]
ENGR00273500 IPUv3 dev: use wait_event_interruptible for ipu task
The ipu task thread checks outstanding tasks to be done on waiting
event uninterruptibly on the function find_task()'s return value.
However, sleeping on waiting event uninterruptibly contributes to
system load average value. This patch changes wait_event() to
wait_event_interruptible() to avoid the load average value inflation.
Peter Chen [Mon, 24 Jun 2013 01:25:59 +0000 (09:25 +0800)]
usb: fix build error without CONFIG_USB_PHY
on i386:
drivers/built-in.o: In function `ci_hdrc_probe':
core.c:(.text+0x20446b): undefined reference to `of_usb_get_phy_mode'
Signed-off-by: Peter Chen <peter.chen@freescale.com> Reported-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Tue, 25 Jun 2013 09:58:05 +0000 (12:58 +0300)]
usb: chipidea: ci_hdrc_imx: access phy via private data
commit ea1418b5f1a (usb: chipidea: i.MX: use devm_usb_get_phy_by_phandle to get
phy) causes the USB host to miss the disconnect/connect events.
In order to reproduce this problem:
- Insert a USB thumb into the USB host port (connection is detected)
- Remove it (no disconnect event will be reported)
- Insert the USB thumb again (connection is not detected)
Fix this problem by accessing the usb_phy structure using the private data
instead of accessing a local structure.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since someone has added camelcase detection to checkpatch.pl, chipidea
udc patches have been very noisy. To make everybody's life easier, this
patch changes camelcase names into something more appropriate to the
coding style. No functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As drvdata is cleared to NULL at probe failure or at removal by the driver
core, we don't have to call pci_set_drvdata(pci, NULL) any longer in each
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: add devicetree helpers for determining dr_mode and phy_type
This adds two little devicetree helper functions for determining the
dr_mode (host, peripheral, otg) and phy_type (utmi, ulpi,...) from
the devicetree.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sascha Hauer [Thu, 13 Jun 2013 14:59:57 +0000 (17:59 +0300)]
usb: chipidea: introduce dual role mode pdata flags
Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: udc: add multiple td support to hardware_{en,de}queue
This patch removes the restriction of having a limited amount of only
four active tds on one endpoint. We use the linked list implementation
to manage all tds which get added and removed by hardware_{en,de}queue.
The removal of this restriction adds the driver to run into a hardware
errata. It's possible that the hardware will still address an transfer
descriptor that already got cleaned up. To solve this the patch also
postpone the cleanup of processed tds by one.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: udc: manage dynamic amount of tds with a linked list
Instead of having a limited number of usable tds in the udc we use a
linked list to support dynamic amount of needed tds for all special
gadget types. This improves throughput.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Thu, 13 Jun 2013 14:59:52 +0000 (17:59 +0300)]
usb: chipidea: improve kconfig
Randy Dunlap <rdunlap@infradead.org> reported this problem
on i386:
> drivers/built-in.o: In function `ci_hdrc_host_init':
> (.text+0x2ce75c): undefined reference to `ehci_init_driver'
>
> When USB_EHCI_HCD=m and USB_CHIPIDEA=y.
In fact, this problem is existed on all platforms which are using
chipidea driver. The root cause of this problem is the chipidea host
uses symbol exported from ehci-hcd, but chipidea core
does not depends on USB_EHCI_HCD. So, chipidea driver
will not be compiled as module if USB_EHCI_HCD=m.
It is very hard to give a perfect solution since chipidea core
depends on USB || USB_GADGET, and chipdiea host depends on
both USB_EHCI_HCD and USB_CHIPIDEA, the same problem exists for
gadget.
To fix this problem, we had to have below assumptions:
- If USB_EHCI_HCD=y && USB_GADGET=y, USB_CHIPIDEA can be 'y'.
- If USB_EHCI_HCD=m && USB_GADGET=y, USB_CHIPIDEA=m
or USB_CHIPIDEA_HOST can't be seen if USB_CHIPIDEA=y.
It will cause compile error due to no glue layer for ehci:
> error: #error "missing bus glue for ehci-hcd"
So, we had to compile USB_CHIPIDEA=m if USB_EHCI_HCD=m,
current ehci hcd core guarantee it.
- If USB_EHCI_HCD=y && USB_GADGET=m, USB_CHIPIDEA=m
or USB_CHIPIDEA_UDC can't be seen if USB_CHIPIDEA=y.
Of cos, the gadget will out of working at this situation,
so the user had to compile USB_CHIPIDEA=m.
- USB_EHCI_HCD=m && USB_GADGET=m, we can't see
USB_CHIPIDEA_HOST and USB_CHIPIDEA_UDC unless
USB_CHIPIDEA=m.
The reason why it has above assumptions:
- If both ehci core and gadget core build as module,
the chipidea has to build as module.
- If one of ehci core or gadget core is built in, another
is built as module, we can only enable the function which
is built in, or enable both roles as modules (USB_CHIPIDEA=m),
since chipidea core driver takes care of both host and device roles.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Thu, 13 Jun 2013 14:59:49 +0000 (17:59 +0300)]
usb: chipidea: ci13xxx_imx: remove reg_vbus
There is no need to keep a 'reg_vbus' indirection, so get rid of it.
The motivation for doing this change is that in the case of error, the current
code only sets the local reg_vbus to NULL instead of updating the private
structure 'data->reg_vbus'.
Updating only the local reg_vbus is wrong, since we currently check for
data->reg_vbus in the ci13xxx_imx_remove() function.
In order to avoid such issue, just use 'data->reg_vbus' directly.
Fabio Estevam [Thu, 13 Jun 2013 14:59:48 +0000 (17:59 +0300)]
usb: chipidea: ci13xxx_imx: fix error path
If usbmisc_ops->post() fails it should point the error path to release all
previously acquired resources, so adjust it to call ci13xxx_remove_device().
While at it, remove the unnecessary 'plat_ci' indirection, as we can directly
use the private structure.
This patch adds iso endpoint support to the device controller.
It makes use of the multiplication bits in the maxpacket field
of the endpoint and calculates the multiplier bits for each
transfer description on every request.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/chipidea/usbmisc_imx.c:246:5: warning: symbol 'usbmisc_imx_drv_init' was not declared. Should it be static?
drivers/usb/chipidea/usbmisc_imx.c:252:6: warning: symbol 'usbmisc_imx_drv_exit' was not declared. Should it be static?
Anson Huang [Fri, 2 Aug 2013 17:29:17 +0000 (13:29 -0400)]
ENGR00273344-2 thermal: imx: make thermal trip temp changeable
Make all thermal trips' temp changeable:
1. Different users may have different definitions about the
trip temp;
2. For testing purpose, if we want to test cooling device's
function, it is easy to change trip temp to cheat the cooling
device to active, otherwise, need to test it using heating box
which is very inconvenient.
ENGR00273344-1 thermal: imx: Update formula for thermal sensor
Thermal sensor used to need two calibration data which are
in Fuse to get a slope for converting thermal sensor's raw
data to real temperature in degree C.
Now we use an universal formula to get real temp
from internal thermal sensor raw data:
Slope = 0.4297157 - (0.0015976 * 25C fuse);
Using universal formula can reduce the effort of chip
calibration, so update the formula.
ASoC: fsl: Disable SSI in trigger() if RE/TE are both cleared
The code enabled SSIEN when triggered by SNDRV_PCM_TRIGGER_START,
so move the disable code to SNDRV_PCM_TRIGGER_STOP for symmetric.
This also allows us to use the SSI driver more flexible so that
it can support some use cases like "aplay S16_LE.wav S24_LE.wav"
which would call the driver in sequence like:
startup()->hw_params(S16_LE)->trigger(START)->tirgger(STOP)->
hw_params(S24_LE)->trigger(START)->tirgger(STOP)->shutdown()
If we disable SSIEN in shutdown(), the second hw_params() would
bypass the sample bits setting while using symmetric_rate.
Signed-off-by: Nicolin Chen <b42378@freescale.com> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Mark Brown <broonie@linaro.org>
Wolfram Sang [Wed, 10 Jul 2013 15:57:46 +0000 (16:57 +0100)]
drivers/tty/serial: don't use devm_pinctrl_get_select_default() in probe
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Huang Shijie <b32955@freescale.com>
serial: imx: distinguish the imx6q uart from the others
We will add the DMA support for the imx uart. For the firmware's limit,
only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can
support the DMA.
This patch adds the necessary macro and helper to distinguish the
imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart"
to enable the DMA support.
This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()".
Jingoo Han [Tue, 25 Jun 2013 01:08:49 +0000 (10:08 +0900)]
serial: remove unnecessary platform_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Barry Song <baohua.song@csr.com> Acked-by: Tony Prisk <linux@prisktech.co.nz> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Huang Shijie <b32955@freescale.com>
Fabio Estevam [Sun, 9 Jun 2013 18:17:18 +0000 (15:17 -0300)]
serial: imx: Fix serial clock unbalance
Since commit 0c375501 (serial: imx: enable the clocks for console), the
imx_startup() function calls clk_prepare_enable conditionally, so we
need to call clk_disable_unprepare inside imx_shutdown() under the same
condition to avoid unbalanced clock calls.
Huang Shijie [Sun, 9 Jun 2013 02:01:19 +0000 (10:01 +0800)]
serial: imx: enable the clocks for console
The console's clocks are disabled after the uart driver is probed.
It makes that we can see less log from the console now
(though we still can get all the log by the `dmesg`).
So enable the clocks for console, and we can see all the log again.
This patch also disables the sport->clk_per when we fail to enable
the sport->clk_ipg;
projects / karo-tx-linux.git / log