Chris Metcalf [Wed, 4 Apr 2012 20:58:27 +0000 (16:58 -0400)]
arch/tile: common DMA code for the GXIO IORPC subsystem
The dma_queue support is used by both the mPipe (networking)
and Trio (PCI) hardware shims on tilegx. This common code is
selected when either of those drivers is built.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 6 Apr 2012 17:52:07 +0000 (13:52 -0400)]
arch/tile: support MMIO-based readb/writeb etc.
Add support for MMIO read/write on tilegx to support GXIO IORPC access.
Similar to the asm-generic version, but we include memory fences on
the writes to be conservative.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Wed, 4 Apr 2012 20:39:58 +0000 (16:39 -0400)]
arch/tile: introduce GXIO IORPC framework for tilegx
The GXIO I/O RPC subsystem handles exporting I/O hardware resources to
Linux and to applications running under Linux.
For instance, memory which is made available for I/O DMA must be mapped
by an I/O TLB; that means that such memory must be locked down by Linux,
so that it is not swapped or otherwise reused, as long as those I/O
TLB entries are active. Similarly, configuring direct hardware access
introduces new validation requirements. If a user application registers
memory, Linux must ensure that the supplied virtual addresses are valid,
and turn them into client physical addresses. Similarly, when Linux then
supplies those client physical addresses to the Tilera hypervisor, it
must in turn validate those before turning them into the real physical
addresses which are required by the hardware.
To the extent that these sorts of activities were required on previous
TILE architecture processors, they were implemented in a device-specific
fashion. This meant that every I/O device had its own Tilera hypervisor
driver, its own Linux driver, and in some cases its own user-level
library support. There was a large amount of more-or-less functionally
identical code in different places, particularly in the different Linux
drivers. For TILE-Gx, this support has been generalized into a common
framework, known as the I/O RPC framework or just IORPC.
The two "gxio" directories (one for headers, one for sources) start
with just a few files in each with this infrastructure commit, but
after adding support for the on-board I/O shims for networking, PCI,
USB, crypto, compression, I2CS, etc., there end up being about 20 files
in each directory.
More information on the IORPC framework is in the <hv/iorpc.h> header,
included in this commit.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 6 Apr 2012 16:53:50 +0000 (12:53 -0400)]
init: fix bug where environment vars can't be passed via boot args
Commit 026cee0086f had the side-effect of dropping the '=' from
the unknown boot arguments that are passed to init as environment
variables. This is because parse_args() puts a NUL in the string
where the '=' was when it passes the "param" and "val" pointers
to the parsing subfunctions. Previously, unknown_bootoption() was
the last parse_args() subfunction to run, and it carefully put back
the '=' character. Now the ignore_unknown_bootoption() is the last
one to run, and it wasn't doing the necessary repair, so the
envp params ended up with the embedded NUL and were no longer
seen as valid environment variables by init.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to tile.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
[cmetcalf@tilera.com: initialize "flags" after "write" updated.] Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:31:08 +0000 (16:31 -0400)]
arch/tile: add descriptive text if the kernel reports a bad trap
If the kernel unexpectedly takes a bad trap, it's convenient to
have it report the type of trap as part of the error. This gives
customers a bit more context before they call up customer support.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:21:17 +0000 (16:21 -0400)]
arch/tile: allow querying cpu module information from the hypervisor
This just adds a few more attributes to the information Linux
can query from the hypervisor for the /sys/hypervisor/board/ directory,
providing part, serial#, revision#, and description for cpu modules
(as opposed to the board itself, or any mezzanine boards).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Fri, 30 Mar 2012 20:01:48 +0000 (16:01 -0400)]
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
The hardwall drain code was not properly implemented for tilegx,
just tilepro, so you couldn't reliably restart an application that
made use of the udn.
In addition, the code was only applicable to the udn (user dynamic
network). On tilegx there is a second user network that is available
(the "idn"), and there is support for having I/O shims deliver
user-level interrupts to applications ("ipi") which functions in a
very similar way to the inter-core permissions used for udn/idn.
So this change also generalizes the code from supporting just the udn
to supports udn/idn/ipi on tilegx.
By default we now use /dev/hardwall/{udn,idn,ipi} with separate
minor numbers for the three devices.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Sun, 1 Apr 2012 18:04:21 +0000 (14:04 -0400)]
arch/tile: support multiple huge page sizes dynamically
This change adds support for a new "super" bit in the PTE, using the new
arch_make_huge_pte() method. The Tilera hypervisor sees the bit set at a
given level of the page table and gangs together 4, 16, or 64 consecutive
pages from that level of the hierarchy to create a larger TLB entry.
One extra "super" page size can be specified at each of the three levels
of the page table hierarchy on tilegx, using the "hugepagesz" argument
on the boot command line. A new hypervisor API is added to allow Linux
to tell the hypervisor how many PTEs to gang together at each level of
the page table.
To allow pre-allocating huge pages larger than the buddy allocator can
handle, this change modifies the Tilera bootmem support to put all of
memory on tilegx platforms into bootmem.
As part of this change I eliminate the vestigial CONFIG_HIGHPTE support,
which never worked anyway, and eliminate the hv_page_size() API in favor
of the standard vma_kernel_pagesize() API.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Sun, 1 Apr 2012 18:01:34 +0000 (14:01 -0400)]
mm: add new arch_make_huge_pte() method for tile support
The tile support for multiple-size huge pages requires tagging
the hugetlb PTE with a "super" bit for PTEs that are multiples of
the basic size of a pagetable span. To set that bit properly
we need to tweak the PTe in make_huge_pte() based on the vma.
This change provides the API for a subsequent tile-specific
change to use.
Reviewed-by: Hillf Danton <dhillf@gmail.com> Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 19:25:59 +0000 (15:25 -0400)]
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
We already had a syscall that did some dcache flushing, but it was
not used in practice. Make it MIPS compatible instead so it can
do both the DCACHE and ICACHE actions. We have code that wants to
be able to use the ICACHE flush mode from userspace so this change
enables that.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 17:58:43 +0000 (13:58 -0400)]
arch/tile: Allow tilegx to build with either 16K or 64K page size
This change introduces new flags for the hv_install_context()
API that passes a page table pointer to the hypervisor. Clients
can explicitly request 4K, 16K, or 64K small pages when they
install a new context. In practice, the page size is fixed at
kernel compile time and the same size is always requested every
time a new page table is installed.
The <hv/hypervisor.h> header changes so that it provides more abstract
macros for managing "page" things like PFNs and page tables. For
example there is now a HV_DEFAULT_PAGE_SIZE_SMALL instead of the old
HV_PAGE_SIZE_SMALL. The various PFN routines have been eliminated and
only PA- or PTFN-based ones remain (since PTFNs are always expressed
in fixed 2KB "page" size). The page-table management macros are
renamed with a leading underscore and take page-size arguments with
the presumption that clients will use those macros in some single
place to provide the "real" macros they will use themselves.
I happened to notice the old hv_set_caching() API was totally broken
(it assumed 4KB pages) so I changed it so it would nominally work
correctly with other page sizes.
Tag modules with the page size so you can't load a module built with
a conflicting page size. (And add a test for SMP while we're at it.)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Thu, 29 Mar 2012 17:39:51 +0000 (13:39 -0400)]
arch/tile: optimize get_user/put_user and friends
Use direct load/store for the get_user/put_user.
Previously, we would call out to a helper routine that would do the
appropriate thing and then return, handling the possible exception
internally. Now we inline the load or store, along with a "we succeeded"
indication in a register; if the load or store faults, we write a
"we failed" indication into the same register and then return to the
following instruction. This is more efficient and gives us more compact
code, as well as being more in line with what other architectures do.
The special futex assembly source file for TILE-Gx also disappears in
this change; we just use the same inlining idiom there as well, putting
the appropriate atomic operations directly into futex_atomic_op_inuser()
(and thus into the FUTEX_WAIT function).
The underlying atomic copy_from_user, copy_to_user functions were
renamed using the (cryptic) x86 convention as copy_from_user_ll and
copy_to_user_ll.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Wed, 28 Mar 2012 17:59:18 +0000 (13:59 -0400)]
arch/tile: allow building Linux with transparent huge pages enabled
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Tue, 27 Mar 2012 19:40:20 +0000 (15:40 -0400)]
arch/tile: use interrupt critical sections less
In general we want to avoid ever touching memory while within an
interrupt critical section, since the page fault path goes through
a different path from the hypervisor when in an interrupt critical
section, and we carefully decided with tilegx that we didn't need
to support this path in the kernel. (On tilepro we did implement
that path as part of supporting atomic instructions in software.)
In practice we always need to touch the kernel stack, since that's
where we store the interrupt state before releasing the critical
section, but this change cleans up a few things. The IRQ_ENABLE
macro is split up so that when we want to enable interrupts in a
deferred way (e.g. for cpu_idle or for interrupt return) we can
read the per-cpu enable mask before entering the critical section.
The cache-migration code is changed to use interrupt masking instead
of interrupt critical sections. And, the interrupt-entry code is
changed so that we defer loading "tp" from per-cpu data until after
we have released the interrupt critical section.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Fix a regression in the /sys/class/infiniband/.../rate attribute --
old kernels used to just return something, even if the underlying
value was out-of-bounds, while 3.4-rc1 returned EINVAL to userspace.
This breaks some applications that check for the error, so go back to
the old behavior."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Don't return EINVAL from sysfs rate attribute for invalid speeds
IB/mlx4: Don't return an invalid speed when a port is down
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fixes from Chris Metcalf:
"This is one important change from Srivatsa Bhat that got dropped when
I put together my pull request for -rc2, plus a trivial change to
remove a compiler warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: avoid unused variable warning in proc.c for tilegx
tile/CPU hotplug: Add missing call to notify_cpu_starting()
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A series of fixes for Conexant 20549 HD-audio codec chip
- A workaround for HDMI hotplug debug prints that annoyed people
- A fix for the new support of platform DAPM contexts
- Many driver-specific minor fixes
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - hide HDMI/ELD printks unless snd.debug=2
ALSA: sound/isa/sscape.c: add missing resource-release code
sound: sound/oss/msnd_pinnacle.c: add vfrees
ALSA: hda - clean up CX20549 test mixer setup
ALSA: hda - CX20549 doesn't need pin_amp_workaround.
ALSA: hda - Remove CD control from model=benq for CX20549
ALSA: hda - fix record volume controls of CX20459 ("Venice")
ALSA: hda - Rename capture sources of CX20549 to match common conventions
ALSA: hda - Fix proc output for ADC amp values of CX20549
ASoC: tegra: fix i2s compilation when !CONFIG_DEBUG_FS
ASoC: set idle_bias_off=1 for all platform DAPM contexts
ASoC: imx-audmux: Check for NULL pointer
ASoC: imx-audmux: Fix ssi port numbers in sysfs
ASoC: ak4642: fixup: mute needs +1 step
MAINTAINERS: Don't list everyone working on Wolfson drivers
MAINTAINERS: Add missing ASoC OMAP co-maintainer
ASoC: pxa: pxa2xx-i2s: add io.h for IOMEM macro
ASoC: tegra: ensure clocks are enabled when touching registers
ASoC: sgtl5000: Enable VAG when DAC/ADC up
ALSA: asihpi - fix return value of hpios_locked_mem_alloc()
Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb core: there is a regression found when used with xine. For
whatever unknown reason, xine (and xine-lib clients) wants that the
frontend to tell what frequency he is using even before the PLL lock
(or at least, it expects a non-zero frequency).
On DVB, the frequency is only actually known after a frequency
zig-zag seek, done by the DVB core. Anyway, the fix was trivial.
That solves Fedora BZ#808871.
- ivtv: fix a regression when selecting the language channel
- uvc: fix a race-related crash
- it913x: fixes firmware loading
- two trivial patches (a dependency issue at a radio driver at sound
Kconfig, and a warning fix on dvb).
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Allow caching of rindex glock
GFS2: Make sure rindex is uptodate before starting transactions
GFS2: use depends instead of select in kconfig
GFS2: put glock reference in error patch of read_rindex_entry
Chris Metcalf [Wed, 11 Apr 2012 16:45:20 +0000 (12:45 -0400)]
arch/tile: avoid unused variable warning in proc.c for tilegx
Until we push the unaligned access support for tilegx, it's silly
to have arch/tile/kernel/proc.c generate a warning about an unused
variable. Extend the #ifdef to cover all the code and data for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
x86: merge 32/64-bit versions of 'strncpy_from_user()' and speed it up
This merges the 32- and 64-bit versions of the x86 strncpy_from_user()
by just rewriting it in C rather than the ancient inline asm versions
that used lodsb/stosb and had been duplicated for (trivial) differences
between the 32-bit and 64-bit versions.
While doing that, it also speeds them up by doing the accesses a word at
a time. Finally, the new routines also properly handle the case of
hitting the end of the address space, which we have never done correctly
before (fs/namei.c has a hack around it for that reason).
Despite all these improvements, it actually removes more lines than it
adds, due to the de-duplication. Also, we no longer export (or define)
the legacy __strncpy_from_user() function (that was defined to not do
the user permission checks), since it's not actually used anywhere, and
the user address space checks are built in to the new code.
Other architecture maintainers have been notified that the old hack in
fs/namei.c will be going away in the 3.5 merge window, in case they
copied the x86 approach of being a bit cavalier about the end of the
address space.
cred: copy_process() should clear child->replacement_session_keyring
keyctl_session_to_parent(task) sets ->replacement_session_keyring,
it should be processed and cleared by key_replace_session_keyring().
However, this task can fork before it notices TIF_NOTIFY_RESUME and
the new child gets the bogus ->replacement_session_keyring copied by
dup_task_struct(). This is obviously wrong and, if nothing else, this
leads to put_cred(already_freed_cred).
change copy_creds() to clear this member. If copy_process() fails
before this point the wrong ->replacement_session_keyring doesn't
matter, exit_creds() won't be called.
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
2) Make the sparc side changes that go along with the infrastructure to
retry faults when blocking on a disk transfer. From Kautuk Consul.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32,leon: fix leon build
sparc/mm/fault_32.c: Port OOM changes to do_sparc_fault
sparc/mm/fault_64.c: Port OOM changes to do_sparc64_fault
Bob Peterson [Tue, 10 Apr 2012 12:56:04 +0000 (08:56 -0400)]
GFS2: Allow caching of rindex glock
This patch allows caching of the rindex glock. We were previously
setting the GL_NOCACHE bit when the glock was released. That forced
the rindex inode to be invalidated, which caused us to re-read
rindex at the next access. However, it caused the glock to be
unnecessarily bounced around the cluster. This patch allows
the glock to remain cached, but it still causes the rindex to be
re-read once it has been written to by gfs2_grow.
Ben and I have tested single-node gfs2_grow cases and I've tested
clustered gfs2_grow cases on my four-node cluster.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
At the point of this error-handling code, both regions and the dma have
been allocated, so free it as done in previous and subsequent
error-handling code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Julia Lawall [Mon, 9 Apr 2012 08:16:32 +0000 (10:16 +0200)]
sound: sound/oss/msnd_pinnacle.c: add vfrees
At the point of this error-handling code, HAVE_DSPCODEH may be undefined,
so free INITCODE and PERMCODE as done elsewhere. A jump and label are
introduced to avoid code duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Frank Rowand [Tue, 10 Apr 2012 00:59:03 +0000 (17:59 -0700)]
modpost: Fix modpost license checking of vmlinux.o
Commit f02e8a6596b7 ("module: Sort exported symbols") sorts symbols
placing each of them in its own elf section. This sorting and merging
into the canonical sections are done by the linker.
Unfortunately modpost to generate Module.symvers file parses vmlinux.o
(which is not linked yet) and all modules object files (which aren't
linked yet). These aren't sanitized by the linker yet. That breaks
modpost that can't detect license properly for modules.
This patch makes modpost aware of the new exported symbols structure.
[ This above is a slightly corrected version of the explanation of the
problem, copied from commit 62a2635610db ("modpost: Fix modpost's
license checking V3"). That commit fixed the problem for module
object files, but not for vmlinux.o. This patch fixes modpost for
vmlinux.o. ]
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com> Signed-off-by: Alessio Igor Bogani <abogani@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task handoff notifier leaks task_struct since it never gets freed
after the callback returns NOTIFY_OK, which means it is responsible for
doing so.
It turns out the lowmemorykiller actually doesn't need this notifier at
all. It's used to prevent unnecessary killing by waiting for a thread
to exit as a result of lowmem_shrink(), however, it's possible to do
this in the same way the kernel oom killer works by setting TIF_MEMDIE
and avoid killing if we're still waiting for it to exit.
The kernel oom killer will already automatically set TIF_MEMDIE for
threads that are attempting to allocate memory that have a fatal signal.
The thread selected by lowmem_shrink() will have such a signal after the
lowmemorykiller sends it a SIGKILL, so this won't result in an
unnecessary use of memory reserves for the thread to exit.
This has the added benefit that we don't have to rely on
CONFIG_PROFILING to prevent needlessly killing tasks.
Reported-by: Werner Landgraf <w.landgraf@ru.ru> Cc: stable@vger.kernel.org Signed-off-by: David Rientjes <rientjes@google.com> Acked-by: Colin Cross <ccross@android.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following gcc complain
arch/um/kernel/skas/mmu.c: In function 'uml_setup_stubs':
arch/um/kernel/skas/mmu.c:106:16: warning: unused variable 'pages' [-Wunused-variable]
Signed-Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Srivatsa S. Bhat [Thu, 22 Mar 2012 11:29:11 +0000 (16:59 +0530)]
tile/CPU hotplug: Add missing call to notify_cpu_starting()
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Al Viro [Mon, 9 Apr 2012 17:59:00 +0000 (13:59 -0400)]
um: fix linker script generation
while we can't just use -U$(SUBARCH), we still need to kill idiotic define
(implicit -Di386=1), both for SUBARCH=i386 and SUBARCH=x86/CONFIG_64BIT=n
builds.
Laurent Pinchart [Tue, 27 Mar 2012 08:51:00 +0000 (05:51 -0300)]
[media] uvcvideo: Fix race-related crash in uvc_video_clock_update()
The driver frees the clock samples buffer before stopping the video
buffers queue. If a DQBUF call arrives in-between,
uvc_video_clock_update() will be called with a NULL clock samples
buffer, leading to a crash. This occurs very frequently when using the
webcam with the flash browser plugin.
Move clock initialization/cleanup to uvc_video_enable() in order to free
the clock samples buffer after the queue is stopped. Make sure the clock
is reset at resume time to avoid miscalculating timestamps.
Hans Verkuil [Sun, 1 Apr 2012 18:24:48 +0000 (15:24 -0300)]
[media] Drivers/media/radio: Fix build error
On Sunday, April 01, 2012 21:09:34 Tracey Dent wrote:
> radio-maxiradio depends on SND_FM801_TEA575X_BOOL to build or will
> result in an build error such as:
>
> Kernel: arch/x86/boot/bzImage is ready (#1)
> ERROR: "snd_tea575x_init" [drivers/media/radio/radio-maxiradio.ko] undefined!
> ERROR: "snd_tea575x_exit" [drivers/media/radio/radio-maxiradio.ko] undefined!
> WARNING: modpost: Found 6 section mismatch(es).
> To see full details build your kernel with:
> 'make CONFIG_DEBUG_SECTION_MISMATCH=y'
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Select CONFIG_SND_TEA575X to fixes problem and enable
> the driver to be built as desired.
>
> v2:
> instead of selecting CONFIG_SND_FM801_TEA575X_BOOL, select
> CONFIG_SND_TEA575X, which in turns selects CONFIG_SND_FM801_TEA575X_BOOL
> and any other dependencies for it to build.
No, this is the correct patch:
RADIO_MAXIRADIO should be treated just like RADIO_SF16FMR2, I just didn't
realize at the time that it had to be added as a SND_TEA575X dependency.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Shea Levy <shea@shealevy.com> Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chris Rankin [Fri, 6 Apr 2012 21:38:18 +0000 (18:38 -0300)]
[media] dvb_frontend: regression fix: userspace ABI broken for xine
The commit e399ce77e6e has broken the DVB ABI for xine:
The problem is that xine is expecting every event after a successful
FE_SET_FRONTEND ioctl to have a non-zero frequency parameter, regardless
of whether the tuning process has LOCKed yet. What used to happen is
that the events inherited the initial tuning parameters from the
FE_SET_FRONTEND call. However, the fepriv->parameters_out struct is now
not initialised until the status contains the FE_HAS_LOCK bit.
You might argue that this behaviour is intentional, except that if an
application other than xine uses the DVB adapter and manages to set the
parameters_out.frequency field to something other than zero, then xine
no longer has any problems until either the adapter is replugged or the
kernel modules reloaded. This can only mean that the
fepriv->parameters_out struct still contains the (stale) tuning
information from the previous application.
Signed-off-by: Chris Rankin <rankincj@yahoo.com> Cc: stable@kernel.org # for kernel version 3.3 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
Merge branch 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: fixes for 3.4
A bunch of driver-specific fixes and one generic fix for the new support
for platform DAPM contexts - we were picking the wrong default for the
idle_bias_off setting which was meaning we weren't actually achieving
any useful runtime PM on platform devices.
Michael Karcher [Fri, 6 Apr 2012 13:34:18 +0000 (15:34 +0200)]
ALSA: hda - Remove CD control from model=benq for CX20549
The ID used for detection of the BenQ R55E actually identifies the
Quanta TW3 ODM design, which is also used for the Gigabyte W551 laptop
series. Schematics on the internet clearly indicate that the "Port C"
(analog input connected to record source #4 and mixer input #4) is
unconnected.
Playing an audio CD through analog playback (using cdplay from cdtools)
produces no sound, even with the mixer input labelled "CD" enabled, and
the volume control in the CD drive set to maximum. This indicates the
connection is really not present.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michael Karcher [Fri, 6 Apr 2012 13:34:17 +0000 (15:34 +0200)]
ALSA: hda - fix record volume controls of CX20459 ("Venice")
The "input converter" widget of the CX20459 has only one input amplifier,
expose that one as "Capture Volume/Capture Switch". The actual record
source selection is already exposed through the separately installed
input mux.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Merge branch '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull target fixes from Nicholas Bellinger:
"Pull two tcm_fc fabric related fixes for -rc2:
Note that both have been CC'ed to stable, and patch #1 is the
important one that addresses a memory corruption bug related to FC
exchange timeouts + command abort.
Thanks again to MDR for tracking down this issue!"
* '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Do not free tpg structure during wq allocation failure
tcm_fc: Add abort flag for gracefully handling exchange timeout
Mark Rustad [Tue, 3 Apr 2012 17:24:52 +0000 (10:24 -0700)]
tcm_fc: Do not free tpg structure during wq allocation failure
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Acked-by: Kiran Patil <Kiran.patil@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark Rustad [Tue, 3 Apr 2012 17:24:41 +0000 (10:24 -0700)]
tcm_fc: Add abort flag for gracefully handling exchange timeout
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Acked-by: Kiran Patil <Kiran.patil@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
Merge tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
- Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
- Fix module reloading on omap_hsmmc.
- Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
* tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (28 commits)
mmc: use really long write timeout to deal with crappy cards
mmc: sdhci-dove: Fix compile error by including module.h
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Revert "mmc: sdhci-pci: Add MSI support"
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
mmc: core: fix power class selection
mmc: omap_hsmmc: fix module re-insertion
mmc: omap_hsmmc: convert to module_platform_driver
mmc: omap_hsmmc: make it behave well as a module
mmc: omap_hsmmc: trivial cleanups
mmc: omap_hsmmc: context save after enabling runtime pm
mmc: omap_hsmmc: use runtime put sync in probe error patch
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
mmc: bus: print bus speed mode of UHS-I card
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
mmc: sh_mmcif: Simplify calculation of mmc->f_min
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc: sh_mmcif: double clock speed
mmc: block: Remove use of mmc_blk_set_blksize
mmc: atmel-mci: add support for odd clock dividers
...
Make the "word-at-a-time" helper functions more commonly usable
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
cpuidle: Fix panic in CPU off-lining with no idle driver
Fix a NULL pointer dereference panic in cpuidle_play_dead() during
CPU off-lining when no cpuidle driver is registered. A cpuidle
driver may be registered at boot-time based on CPU type. This patch
allows an off-lined CPU to enter HLT-based idle in this condition.
Signed-off-by: Toshi Kani <toshi.kani@hp.com> Cc: Boris Ostrovsky <boris.ostrovsky@amd.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Len Brown <len.brown@intel.com>
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Jan Beulich [Mon, 2 Apr 2012 14:32:22 +0000 (15:32 +0100)]
xen/pciback: fix XEN_PCI_OP_enable_msix result
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The reason we are dying is b/c the call acpi_get_override_irq() is used,
which returns the polarity and trigger for the IRQs. That function calls
mp_find_ioapics to get the 'struct ioapic' structure - which along with the
mp_irq[x] is used to figure out the default values and the polarity/trigger
overrides. Since the mp_find_ioapics now returns -1 [b/c the IOAPIC is filled
with 0xffffffff], the acpi_get_override_irq() stops trying to lookup in the
mp_irq[x] the proper INT_SRV_OVR and we can't install the SCI interrupt.
The proper fix for this is going in v3.5 and adds an x86_io_apic_ops
struct so that platforms can override it. But for v3.4 lets carry this
work-around. This patch does that by providing a slightly different variant
of the fake IOAPIC entries.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Igor Mammedov [Tue, 27 Mar 2012 17:31:08 +0000 (19:31 +0200)]
xen: only check xen_platform_pci_unplug if hvm
commit b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Stephen Warren [Fri, 6 Apr 2012 05:11:16 +0000 (23:11 -0600)]
ASoC: tegra: fix i2s compilation when !CONFIG_DEBUG_FS
Commit d4a2eca "ASoC: Tegra I2S: Remove dependency on pdev->id" changed
the prototype of tegra_i2s_debug_add, but didn't update the dummy inline
used when !CONFIG_DEBUG_FS. Fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: <stable@vger.kernel.org> # 3.3
Eric Dumazet [Fri, 6 Apr 2012 08:49:10 +0000 (10:49 +0200)]
net: fix a race in sock_queue_err_skb()
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 5 Apr 2012 22:17:46 +0000 (22:17 +0000)]
netlink: fix races after skb queueing
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:40:06 +0000 (14:40 +0000)]
doc, net: Remove instruction to set net_device::trans_start
Commit 08baf561083bc27a953aa087dd8a664bb2b88e8e ('net:
txq_trans_update() helper') made it unnecessary for most drivers to
set net_device::trans_start (or netdev_queue::trans_start).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:39:10 +0000 (14:39 +0000)]
doc, net: Remove obsolete reference to dev->poll
Commit bea3348eef27e6044b6161fd04c3152215f96411 ('[NET]: Make NAPI
polling independent of struct net_device objects.') removed the
automatic disabling of NAPI polling by dev_close(), and drivers
must now do this themselves.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:38:49 +0000 (14:38 +0000)]
ethtool: Remove exception to the requirement of holding RTNL lock
Commit e52ac3398c3d772d372b9b62ab408fd5eec96840 ('net: Use device
model to get driver name in skb_gso_segment()') removed the only
in-tree caller of ethtool ops that doesn't hold the RTNL lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
Pull a few blackfin compile fixes from Bob Liu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: update defconfig for bf527-ezkit
blackfin: gpio: fix compile error if !CONFIG_GPIOLIB
blackfin: fix L1 data A overflow link issue
Bob Liu [Thu, 5 Apr 2012 02:40:35 +0000 (10:40 +0800)]
blackfin: update defconfig for bf527-ezkit
To fix compile error:
drivers/usb/musb/blackfin.h:51:3: error: #error "Please use PIO mode in MUSB
driver on bf52x chip v0.0 and v0.1"
make[4]: *** [drivers/usb/musb/blackfin.o] Error 1
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm
Pull an APM fix from Jiri Kosina:
"One deadlock/race fix from Niel that got introduced when we were
moving away from freezer_*_count() to wait_event_freezable()."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
APM: fix deadlock in APM_IOC_SUSPEND ioctl
Paul Walmsley [Mon, 12 Mar 2012 10:58:00 +0000 (04:58 -0600)]
mmc: use really long write timeout to deal with crappy cards
Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.
This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:
* With certain SD cards timeouts like the following have been seen
due to an improper calculation of the dto value:
mmcblk0: error -110 transferring data, sector 4126233, nr 8,
card status 0xc00
* By removing the dto calculation and setting the timeout value
to the maximum specified by the SD card specification part A2
section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
relevant ones are:
* http://talk.maemo.org/showthread.php?p=1000707#post1000707
* http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Al Cooper [Fri, 16 Mar 2012 19:54:17 +0000 (15:54 -0400)]
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com> Acked-by: Arindam Nath <arindam.nath@amd.com> Acked-by: Philip Rakity <prakity@marvell.com> Acked-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Chris Ball [Tue, 3 Apr 2012 20:48:32 +0000 (16:48 -0400)]
Revert "mmc: sdhci-pci: Add MSI support"
This reverts commit e6039832bed9a9b967796d7021f17f25b625b616.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.
According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.
Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Acked-by: Girish K S <girish.shivananjappa@linaro.org> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
projects / karo-tx-linux.git / log