rsxx: Fix possible kernel panic with invalid config.
This patch fixes a possible Kernel Panic on driver load if
the configuration on the card is messed up or not yet set.
The driver could possible give a 32 bit unsigned all Fs to
the kernel as the device's block size.
Now we only write the block size to the kernel if the
configuration from the card is valid.
Also, driver version is being updated.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a bug in which discards were always
calling pci_unmap_page. Discards should never call the
pci_unmap_page function call because they are never mapped.
This caused a race condition on PowerPC systems when issuing
discards, writes, and reads all at the same time. The
pci_map_page function would eventually map logical address
0 for a read or write. Discards are always assigned a DMA
address of 0 because they are never mapped. So if
pci_map_page mapped address 0 for a DMA and a discard was
"unmapped" then the address would be freed and would cause
an EEH event to occur when Hardware accesses the address.
The pci_dma_mapping_error function declares -1 a DMA_ERROR
not 0 like initially thought So before we would never unmap
discards because they were considered NULL.
Lars Ellenberg [Wed, 23 Oct 2013 08:59:19 +0000 (10:59 +0200)]
drbd: avoid to shrink max_bio_size due to peer re-configuration
For a long time, the receiving side has spread "too large" incoming
requests over multiple bios. No need to shrink our max_bio_size
(max_hw_sectors) if the peer is reconfigured to use a different storage.
The problem manifests itself if we are not the top of the device stack
(DRBD is used a LVM PV).
A hardware reconfiguration on the peer may cause the supported
max_bio_size to shrink, and the connection handshake would now
unnecessarily shrink the max_bio_size on the active node.
There is no way to notify upper layers that they have to "re-stack"
their limits. So they won't notice at all, and may keep submitting bios
that are suddenly considered "too large for device".
We already check for compatibility and ignore changes on the peer,
the code only was masked out unless we have a fully established connection.
We just need to allow it a bit earlier during the handshake.
Also consider max_hw_sectors in our merge bvec function, just in case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Philipp Reisner [Wed, 23 Oct 2013 08:59:17 +0000 (10:59 +0200)]
drbd: Fix adding of new minors with freshly created meta data
Online adding of new minors with freshly created meta data
to an resource with an established connection failed, with a
wrong state transition on one side on one side of the new minor.
Freshly created meta-data has a la_size (last agreed size) of 0.
When we online add such devices, the code wrongly got into
the code path for resyncing new storage that was added while
the disk was detached.
Fixed that by making the GREW from ZERO a special case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Philipp Reisner [Wed, 23 Oct 2013 08:59:16 +0000 (10:59 +0200)]
drbd: Fix an connection drop issue after enabling allow-two-primaries
Since drbd-8.4.0 it is possible to change the allow-two-primaries
network option while the connection is established.
The sequence code used to partially order packets from the
data socket with packets from the meta-data socket, still assued
that the allow-two-primaries option is constant while the
connection is established.
I.e.
On a node that has the RESOLVE_CONFLICTS bits set, after enabling
allow-two-primaries, when receiving the next data packet it timed out
while waiting for the necessary packets on the data socket to arrive
(wait_for_and_update_peer_seq() function).
Fixed that by always tracking the sequence number, but only waiting
for it if allow-two-primaries is set.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mike Snitzer [Fri, 18 Oct 2013 15:44:49 +0000 (09:44 -0600)]
block: properly stack underlying max_segment_size to DM device
Without this patch all DM devices will default to BLK_MAX_SEGMENT_SIZE
(65536) even if the underlying device(s) have a larger value -- this is
due to blk_stack_limits() using min_not_zero() when stacking the
max_segment_size limit.
Jens Axboe [Thu, 17 Oct 2013 22:38:30 +0000 (16:38 -0600)]
block: disable cpqarray in Kconfig
Mike writes:
"cpqarray hasn't been used in over 12 years. It's doubtful that anyone
still uses the board. It's time the driver was removed from the mainline
kernel. The only updates these days are minor and mostly done by people
outside of HP."
If nobody yells, we'll remove it from the kernel tree completely
for 3.15.
Tomoki Sekiyama [Tue, 15 Oct 2013 22:42:19 +0000 (16:42 -0600)]
elevator: acquire q->sysfs_lock in elevator_change()
Add locking of q->sysfs_lock into elevator_change() (an exported function)
to ensure it is held to protect q->elevator from elevator_init(), even if
elevator_change() is called from non-sysfs paths.
sysfs path (elv_iosched_store) uses __elevator_change(), non-locking
version, as the lock is already taken by elv_iosched_store().
(*) When del_timer_sync() is called, lock_timer_base() will loop infinitely
while timer->base == NULL. In this case, as timer will never initialized,
it results in lockup.
This patch introduces acquisition of q->sysfs_lock around elevator_init()
into blk_init_allocated_queue(), to provide mutual exclusion between
initialization of the q->scheduler and switching of the scheduler.
This should fix this bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=902012
This fixes a kernel panic injected by commit id 8d26750143341831bc312f61c5ed141eeb75b8d0 where discards
are getting mapped through the pci_map_page function call.
The driver will now start verifying that a dma is not a
discard before issuing a the pci_map_page function call.
Also, we are updating the driver version.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
David Milburn [Thu, 23 May 2013 21:23:45 +0000 (16:23 -0500)]
mtip32xx: dynamically allocate buffer in debugfs functions
Dynamically allocate buf to prevent warnings:
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_device_status’:
drivers/block/mtip32xx/mtip32xx.c:2823: warning: the frame size of 1056 bytes is larger than 1024 bytes
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_registers’:
drivers/block/mtip32xx/mtip32xx.c:2894: warning: the frame size of 1056 bytes is larger than 1024 bytes
drivers/block/mtip32xx/mtip32xx.c: In function ‘mtip_hw_read_flags’:
drivers/block/mtip32xx/mtip32xx.c:2917: warning: the frame size of 1056 bytes is larger than 1024 bytes
Signed-off-by: David Milburn <dmilburn@redhat.com> Acked-by: Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Asai Thambi S P [Wed, 11 Sep 2013 19:14:42 +0000 (13:14 -0600)]
mtip32xx: Add SRSI support
This patch add support for SRSI(Surprise Removal Surprise Insertion).
Approach:
---------
Surprise Removal:
-----------------
On surprise removal of the device, gendisk, request queue, device index, sysfs
entries, etc are retained as long as device is in use - mounted filesystem,
device opened by an application, etc. The service thread breaks out of the main
while loop, waits for pci remove to exit, and then waits for device to become
free. When there no holders of the device, service thread cleans up the block
and device related stuff and returns.
Surprise Insertion:
-------------------
No change, this scenario follows the normal pci probe() function flow.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
The pci_map_page function has been moved into our
issued workqueue to prevent an us running out of
mappable addresses on non-HWWD PCIe x8 slots. The
maximum amount that can possible be mapped at one
time now is: 255 dmas X 4 dma channels X 4096 Bytes.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
rsxx: Handling failed pci_map_page on PowerPC and double free.
The rsxx driver was not checking the correct value during a
pci_map_page failure. Fixing this also uncovered a
double free if the bio was returned before it was
broken up into indiviadual 4k dmas, that is also
fixed here.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mikulas Patocka [Tue, 15 Oct 2013 20:14:38 +0000 (14:14 -0600)]
loop: fix crash when using unassigned loop device
When the loop module is loaded, it creates 8 loop devices /dev/loop[0-7].
The devices have no request routine and thus, when they are used without
being assigned, a crash happens.
For example, these commands cause crash (assuming there are no used loop
devices):
If the permission check fails, we drop a reference to the blkif without
having taken it in the first place. The bug was introduced in commit 604c499cbbcc3d5fe5fb8d53306aa0fae1990109 (xen/blkback: Check device
permissions before allowing OP_DISCARD).
Cc: stable@vger.kernel.org Cc: Jan Beulich <JBeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Roger Pau Monne [Mon, 12 Aug 2013 10:53:43 +0000 (12:53 +0200)]
xen-blkfront: improve aproximation of required grants per request
Improve the calculation of required grants to process a request by
using nr_phys_segments instead of always assuming a request is going
to use all posible segments.
nr_phys_segments contains the number of scatter-gather DMA addr+len
pairs, which is basically what we put at every granted page.
for_each_sg iterates over the DMA addr+len pairs and uses a grant
page for each of them.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Roger Pau Monne [Mon, 12 Aug 2013 10:53:44 +0000 (12:53 +0200)]
xen-blkfront: revoke foreign access for grants not mapped by the backend
There's no need to keep the foreign access in a grant if it is not
persistently mapped by the backend. This allows us to free grants that
are not mapped by the backend, thus preventing blkfront from hoarding
all grants.
The main effect of this is that blkfront will only persistently map
the same grants as the backend, and it will always try to use grants
that are already mapped by the backend. Also the number of persistent
grants in blkfront is the same as in blkback (and is controlled by the
value in blkback).
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Acked-by: Matt Wilson <msw@amazon.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
this_cpu_inc(y)
Signed-off-by: Christoph Lameter <cl@linux.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
The brd change should be backported to stable kernels starting with 2.6.25.
The loop change should be backported to stable kernels starting with 2.6.22.
Mikulas Patocka [Mon, 14 Oct 2013 16:12:24 +0000 (12:12 -0400)]
loop: fix crash if blk_alloc_queue fails
loop: fix crash if blk_alloc_queue fails
If blk_alloc_queue fails, loop_add cleans up, but it doesn't clean up the
identifier allocated with idr_alloc. That causes crash on module unload in
idr_for_each(&loop_index_idr, &loop_exit_cb, NULL); where we attempt to
remove non-existed device with that id.
This fix should be backported to stable kernels starting with 2.6.37. Note
that in the kernels prior to 3.5 the affected code is different, but the
bug is still there - bdi_init is called and bdi_destroy isn't.
After digging through the code, I think there may be a race between the
request completion and the timer handler running.
A timer is started for each request put on the device's queue (see
blk_start_request->blk_add_timer). If the request does not complete
before the timer expires, the timer handler (blk_rq_timed_out_timer)
will mark the request complete atomically:
and then call blk_rq_timed_out. The latter function will call
scsi_times_out, which will return one of BLK_EH_HANDLED,
BLK_EH_RESET_TIMER or BLK_EH_NOT_HANDLED. If BLK_EH_RESET_TIMER is
returned, blk_clear_rq_complete is called, and blk_add_timer is again
called to simply wait longer for the request to complete.
Now, if the request happens to complete while this is going on, what
happens? Given that we know the completion handler will bail if it
finds the REQ_ATOM_COMPLETE bit set, we need to focus on the completion
handler running after that bit is cleared. So, from the above
paragraph, after the call to blk_clear_rq_complete. If the completion
sets REQ_ATOM_COMPLETE before the BUG_ON in blk_add_timer, we go boom
there (I haven't seen this in the cores). Next, if we get the
completion before the call to list_add_tail, then the timer will
eventually fire for an old req, which may either be freed or reallocated
(there is evidence that this might be the case). Finally, if the
completion comes in *after* the addition to the timeout list, I think
it's harmless. The request will be removed from the timeout list,
req_atom_complete will be set, and all will be well.
This will only actually explain the coredumps *IF* the request
structure was freed, reallocated *and* queued before the error handler
thread had a chance to process it. That is possible, but it may make
sense to keep digging for another race. I think that if this is what
was happening, we would see other instances of this problem showing up
as null pointer or garbage pointer dereferences, for example when the
request structure was not re-used. It looks like we actually do run
into that situation in other reports.
This patch moves the BUG_ON(test_bit(REQ_ATOM_COMPLETE,
&req->atomic_flags)); from blk_add_timer to the only caller that could
trip over it (blk_start_request). It then inverts the calls to
blk_clear_rq_complete and blk_add_timer in blk_rq_timed_out to address
the race. I've boot tested this patch, but nothing more.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Hannes Reinecke <hare@suse.de> Cc: stable@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jan Kara [Tue, 17 Sep 2013 20:30:31 +0000 (22:30 +0200)]
blktrace: Send BLK_TN_PROCESS events to all running traces
Currently each task sends BLK_TN_PROCESS event to the first traced
device it interacts with after a new trace is started. When there are
several traced devices and the task accesses more devices, this logic
can result in BLK_TN_PROCESS being sent several times to some devices
while it is never sent to other devices. Thus blkparse doesn't display
command name when parsing some blktrace files.
Fix the problem by sending BLK_TN_PROCESS event to all traced devices
when a task interacts with any of them.
Signed-off-by: Jan Kara <jack@suse.cz> Review-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Mon, 14 Oct 2013 17:02:23 +0000 (10:02 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Some more ARM fixes, nothing particularly major here. The biggest
change is to fix the SMP_ON_UP code so that it works with TI's Aegis
cores"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7851/1: check for number of arguments in syscall_get/set_arguments()
ARM: 7846/1: Update SMP_ON_UP code to detect A9MPCore with 1 CPU devices
ARM: 7845/1: sharpsl_param.c: fix invalid memory access for pxa devices
ARM: 7843/1: drop asm/types.h from generic-y
ARM: 7842/1: MCPM: don't explode if invoked without being initialized first
Linus Torvalds [Mon, 14 Oct 2013 16:31:08 +0000 (09:31 -0700)]
Merge tag 'pm+acpi-3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These fix two recent bugs in ACPIPHP (ACPI-based PCI hotplug) and
update a bunch of web links and e-mail addresses in MAINTAINERS, docs
and Kconfig that either are stale or will expire soon.
Specifics:
- The WARN_ON() in acpiphp_enumerate_slots() triggers as a false
positive in some cases, so drop it.
- Add a missing pci_dev_put() to an error code path in
acpiphp_enumerate_slots().
- Replace my old e-mail address that's going to expire with a new
one.
- Update ACPI web links and git tree information in MAINTAINERS.
- Update links to the Linux-ACPI project's page in MAINTAINERS.
- Update some stale links and e-mail addresses under Documentation
and in the ACPI Kconfig file"
* tag 'pm+acpi-3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug / PCI: Drop WARN_ON() from acpiphp_enumerate_slots()
ACPI / hotplug / PCI: Fix error code path in acpiphp_enumerate_slots()
ACPI / PM / Documentation: Replace outdated project links and addresses
MAINTAINERS / ACPI: Update links to the Linux-ACPI project web page
MAINTAINERS / ACPI: Update links and git tree information
MAINTAINERS / Documentation: Update Rafael's e-mail address
Linus Torvalds [Sun, 13 Oct 2013 18:41:26 +0000 (11:41 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sunxi: Fix section mismatch
watchdog: kempld_wdt: Fix bit mask definition
watchdog: ts72xx_wdt: locking bug in ioctl
Maxime Ripard [Sat, 5 Oct 2013 14:20:17 +0000 (16:20 +0200)]
watchdog: sunxi: Fix section mismatch
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
AKASHI Takahiro [Wed, 9 Oct 2013 14:58:29 +0000 (15:58 +0100)]
ARM: 7851/1: check for number of arguments in syscall_get/set_arguments()
In ftrace_syscall_enter(),
syscall_get_arguments(..., 0, n, ...)
if (i == 0) { <handle ORIG_r0> ...; n--;}
memcpy(..., n * sizeof(args[0]));
If 'number of arguments(n)' is zero and 'argument index(i)' is also zero in
syscall_get_arguments(), none of arguments should be copied by memcpy().
Otherwise 'n--' can be a big positive number and unexpected amount of data
will be copied. Tracing system calls which take no argument, say sync(void),
may hit this case and eventually make the system corrupted.
This patch fixes the issue both in syscall_get_arguments() and
syscall_set_arguments().
Cc: <stable@vger.kernel.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sun, 13 Oct 2013 16:59:10 +0000 (09:59 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes this week, mostly OMAP related. Nothing stands
out as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
including the Chromebooks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message] Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 13 Oct 2013 16:33:32 +0000 (09:33 -0700)]
Merge tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Linus Torvalds [Sun, 13 Oct 2013 16:13:28 +0000 (09:13 -0700)]
Merge branch 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This patchset includes a bugfix to prevent a kernel crash when memory
in page zero is accessed by the kernel itself, e.g. via
probe_kernel_read().
Furthermore we now export flush_cache_page() which is needed
(indirectly) by the lustre filesystem. The other patches remove
unused functions and optimizes the page fault handler to only evaluate
variables if needed, which again protects against possible kernel
crashes"
* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: let probe_kernel_read() capture access to page zero
parisc: optimize variable initialization in do_page_fault
parisc: fix interruption handler to respect pagefault_disable()
parisc: mark parisc_terminate() noreturn and cold.
parisc: remove unused syscall_ipi() function.
parisc: kill SMP single function call interrupt
parisc: Export flush_cache_page() (needed by lustre)
Linus Torvalds [Sun, 13 Oct 2013 16:02:03 +0000 (09:02 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Another week, time to send another fixes request taking time out of
extended weekend for the festivities in this part of the world.
We have two fixes from Sergei for rcar driver and one fixing memory
leak of edma driver by Geyslan"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: edma.c: remove edma_desc leakage
rcar-hpbdma: add parameter to set_slave() method
rcar-hpbdma: remove shdma_free_irq() calls
parisc: optimize variable initialization in do_page_fault
The attached change defers the initialization of the variables tsk, mm
and flags until they are needed. As a result, the code won't crash if a
kernel probe is done with a corrupt context and the code will be better
optimized.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Tue, 1 Oct 2013 19:54:46 +0000 (21:54 +0200)]
parisc: fix interruption handler to respect pagefault_disable()
Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel. The
problem is, that in print_worker_info() we try to read the workqueue info via
the probe_kernel_read() functions which use pagefault_disable() to avoid
crashes like this:
probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq));
probe_kernel_read(&wq, &pwq->wq, sizeof(wq));
probe_kernel_read(name, wq->name, sizeof(name) - 1);
The problem here is, that the first probe_kernel_read(&pwq) might return zero
in pwq and as such the following probe_kernel_reads() try to access contents of
the page zero which is read protected and generate a kernel segfault.
With this patch we fix the interruption handler to call parisc_terminate()
directly only if pagefault_disable() was not called (in which case
preempt_count()==0). Otherwise we hand over to the pagefault handler which
will try to look up the faulting address in the fixup tables.
Signed-off-by: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v3.0+ Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
Jiang Liu [Wed, 11 Sep 2013 16:07:18 +0000 (00:07 +0800)]
parisc: kill SMP single function call interrupt
Commit 9a46ad6d6df3b54 "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Cc: Jiang Liu <liuj97@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
Olga reported that file descriptors opened with O_PATH do not work with
fstatfs(), found during further development of ksh93's thread support.
There is no reason to not allow O_PATH file descriptors here (fstatfs is
very much a path operation), so use "fdget_raw()". See commit 55815f70147d ("vfs: make O_PATH file descriptors usable for 'fstat()'")
for a very similar issue reported for fstat() by the same team.
Reported-and-tested-by: ольга крыжановская <olga.kryzhanovska@gmail.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # O_PATH introduced in 3.0+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Oct 2013 19:55:15 +0000 (12:55 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A bug fix and performance regression fix for ext4"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix memory leak in xattr
ext4: fix performance regression in writeback of random writes
Linus Torvalds [Sat, 12 Oct 2013 19:54:24 +0000 (12:54 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've got more bug fixes in my for-linus branch:
One of these fixes another corner of the compression oops from last
time. Miao nailed down some problems with concurrent snapshot
deletion and drive balancing.
I kept out one of his patches for more testing, but these are all
stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix oops caused by the space balance and dead roots
Btrfs: insert orphan roots into fs radix tree
Btrfs: limit delalloc pages outside of find_delalloc_range
Btrfs: use right root when checking for hash collision
Linus Torvalds [Sat, 12 Oct 2013 18:53:43 +0000 (11:53 -0700)]
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All stable fixes except for a trivial headset mic fixup: the removal
of bogus frame checks in snd-usb-usx2y driver that have regressed in
the recent kernel versions, the HD-audio HDMI channel map fix, and a
few HD-audio device-specific fixes"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
ALSA: hda - Add a headset mic model for ALC269 and friends
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
ALSA: hda - Add fixup for ASUS N56VZ
ALSA: hda - hdmi: Fix channel map switch not taking effect
ALSA: hda - Fix mono speakers and headset mic on Dell Vostro 5470
ALSA: snd-usb-usx2y: remove bogus frame checks
Linus Torvalds [Sat, 12 Oct 2013 18:52:40 +0000 (11:52 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"We had various reports of problems with deferred probing in the I2C
subsystem, so this pull requst is a little bigger than usual.
Most issues should be addressed now so devices will be found
correctly. A few ususal driver bugfixes are in here, too"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-mux-pinctrl: use deferred probe when adapter not found
i2c: i2c-arb-gpio-challenge: use deferred probe when adapter not found
i2c: i2c-mux-gpio: use deferred probing
i2c: i2c-mux-gpio: don't ignore of_get_named_gpio errors
i2c: omap: Clear ARDY bit twice
i2c: Not all adapters have a parent
i2c: i2c-stu300: replace platform_driver_probe to support deferred probing
i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
i2c: i2c-imx: replace platform_driver_probe to support deferred probing
i2c: i2c-designware-platdrv: replace platform_driver_probe to support deferred probing
Dave Jones [Fri, 11 Oct 2013 00:05:35 +0000 (20:05 -0400)]
ext4: fix memory leak in xattr
If we take the 2nd retry path in ext4_expand_extra_isize_ea, we
potentionally return from the function without having freed these
allocations. If we don't do the return, we over-write the previous
allocation pointers, so we leak either way.
Spotted with Coverity.
[ Fixed by tytso to set is and bs to NULL after freeing these
pointers, in case in the retry loop we later end up triggering an
error causing a jump to cleanup, at which point we could have a double
free bug. -- Ted ]
Signed-off-by: Dave Jones <davej@fedoraproject.org> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Cc: stable@vger.kernel.org
Linus Torvalds [Sat, 12 Oct 2013 18:06:18 +0000 (11:06 -0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull gcc "asm goto" miscompilation workaround from Ingo Molnar:
"This is the fix for the GCC miscompilation discussed in the following
lkml thread:
[x86] BUG: unable to handle kernel paging request at 00740060
The bug in GCC has been fixed by Jakub and the fix will be part of the
GCC 4.8.2 release expected to be released next week - so the quirk's
version test checks for <= 4.8.1.
The quirk is only added to compiler-gcc4.h and not to the higher level
compiler.h because all asm goto uses are behind a feature check"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Linus Torvalds [Sat, 12 Oct 2013 17:36:03 +0000 (10:36 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A build fix and a reboot quirk"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Add reboot quirk for Dell Latitude E5410
x86, build, pci: Fix PCI_MSI build on !SMP
Linus Torvalds [Sat, 12 Oct 2013 17:34:14 +0000 (10:34 -0700)]
Merge tag 'arc-fixes-for-3.12-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fix from Vineet Gupta:
"Fix for broken gdb 'jump'"
* tag 'arc-fixes-for-3.12-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc"
Vineet Gupta [Thu, 10 Oct 2013 14:03:57 +0000 (19:33 +0530)]
ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc"
ARCompact TRAP_S insn used for breakpoints, commits before exception is
taken (updating architectural PC). So ptregs->ret contains next-PC and
not the breakpoint PC itself. This is different from other restartable
exceptions such as TLB Miss where ptregs->ret has exact faulting PC.
gdb needs to know exact-PC hence ARC ptrace GETREGSET provides for
@stop_pc which returns ptregs->ret vs. EFA depending on the
situation.
However, writing stop_pc (SETREGSET request), which updates ptregs->ret
doesn't makes sense stop_pc doesn't always correspond to that reg as
described above.
This was not an issue so far since user_regs->ret / user_regs->stop_pc
had same value and both writing to ptregs->ret was OK, needless, but NOT
broken, hence not observed.
With gdb "jump", they diverge, and user_regs->ret updating ptregs is
overwritten immediately with stop_pc, which this patch fixes.
Reported-by: Anton Kolesov <akolesov@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ACPI / hotplug / PCI: Drop WARN_ON() from acpiphp_enumerate_slots()
The WARN_ON() in acpiphp_enumerate_slots() triggers unnecessarily for
devices whose bridges are going to be handled by native PCIe hotplug
(pciehp) and the simplest way to prevent that from happening is to
drop the WARN_ON().
References: https://bugzilla.kernel.org/show_bug.cgi?id=62831 Reported-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 11 Oct 2013 17:41:21 +0000 (10:41 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"All over the map..
- nouveau:
disable MSI, needs more work, will try again next merge window
- radeon:
audio + uvd regression fixes, dpm fixes, reset fixes
- i915:
the dpms fix might fix your haswell
And one pain in the ass revert, so we have VGA arbitration that when
implemented 4-5 years ago really hoped that GPUs could remove
themselves from arbitration completely once they had a kernel driver.
It seems Intel hw designers decided that was too nice a facility to
allow us to have so they removed it when they went on-die (so since
Ironlake at least). Now Alex Williamson added support for VGA
arbitration for newer GPUs however this now exposes itself to
userspace as requireing arbitration of GPU VGA regions and the X
server gets involved and disables things that it can't handle when VGA
access is possibly required around every operation.
So in order to not break userspace we just reverted things back to the
old known broken status so maybe we can try and design out way out.
Ville also had a patch to use stop machine for the two times Intel
needs to access VGA space, that might be acceptable with some rework,
but for now myself and Daniel agreed to just go back"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (23 commits)
Revert "i915: Update VGA arbiter support for newer devices"
Revert "drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done"
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Revert "drm/fb-helper: don't sleep for screen unblank when an oops is in progress"
drm/gma500: fix things after get/put page helpers
drm/nouveau/mc: disable msi support by default, it's busted in tons of places
drm/i915: Only apply DPMS to the encoder if enabled
...
ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Ingo Molnar [Thu, 10 Oct 2013 08:16:30 +0000 (10:16 +0200)]
compiler/gcc4: Add quirk for 'asm goto' miscompilation bug
Fengguang Wu, Oleg Nesterov and Peter Zijlstra tracked down
a kernel crash to a GCC bug: GCC miscompiles certain 'asm goto'
constructs, as outlined here:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
Implement a workaround suggested by Jakub Jelinek.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Suggested-by: Jakub Jelinek <jakub@redhat.com> Reviewed-by: Richard Henderson <rth@twiddle.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: <stable@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Adding drm/i915 into the vga arbiter chain means that X (in a piece of
well-meant paranoia) will do a get/put on the vga decoding around
_every_ accel call down into the ddx. Which results in some nice
performance disasters [1]. This really breaks userspace, by disabling
DRI for everyone, and stops OpenGL from working, this isn't limited
to just the i915 but both the integrated and discrete GPUs on
multi-gpu systems, in other words this causes untold worlds of pain,
Ville tried to come up with a Great Hack to fiddle the required VGA
I/O ops behind everyone's back using stop_machine, but that didn't
really work out [2]. Given that we're fairly late in the -rc stage for
such games let's just revert this all.
One thing we might want to keep is to delay the disabling of the vga
decoding until the fbdev emulation and the fbcon screen is set up. If
we kill vga mem decoding beforehand fbcon can end up with a white
square in the top-left corner it tried to save from the vga memory for
a seamless transition. And we have bug reports on older platforms
which seem to match these symptoms.
But again that's something to play around with in -next.
References: [1] http://lists.x.org/archives/xorg-devel/2013-September/037763.html
References: [2] http://www.spinics.net/lists/intel-gfx/msg34062.html Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 11 Oct 2013 03:07:15 +0000 (13:07 +1000)]
Merge branch 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Regression fixes for audio and UVD, several hang fixes,
some DPM fixes.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: re-enable sw ACR support on pre-DCE4
drm/radeon/dpm: disable bapm on TN asics
drm/radeon: improve soft reset on CIK
drm/radeon: improve soft reset on SI
drm/radeon/dpm: off by one in si_set_mc_special_registers()
drm/radeon/dpm/btc: off by one in btc_set_mc_special_registers()
drm/radeon: forever loop on error in radeon_do_test_moves()
drm/radeon: fix hw contexts for SUMO2 asics
drm/radeon: fix typo in CP DMA register headers
drm/radeon/dpm: disable multiple UVD states
drm/radeon: use hw generated CTS/N values for audio
drm/radeon: fix N/CTS clock matching for audio
drm/radeon: use 64-bit math to calculate CTS values for audio (v2)
drm/edid: catch kmalloc failure in drm_edid_to_speaker_allocation
Sergei Shtylyov [Wed, 25 Sep 2013 22:31:37 +0000 (02:31 +0400)]
rcar-hpbdma: add parameter to set_slave() method
Commit 4981c4dc194efb18f0e9a02f1b43e926f2f0d2bb (DMA: shdma: switch DT mode to
use configuration data from a match table) added a new parameter to set_slave()
method but unfortunately got merged later than commit c4f6c41ba790bbbfcebb4c47a
(dma: add driver for R-Car HPB-DMAC), so that the HPB-DMAC driver retained the
old prototype which caused this warning:
drivers/dma/sh/rcar-hpbdma.c:485: warning: initialization from incompatible
pointer type
The newly added parameter is used to override DMA slave address from 'struct
hpb_dmae_slave_config', so we have to add the 'slave_addr' field to 'struct
hpb_dmae_chan', conditionally assign it in set_slave() method, and return in
slave_addr() method.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/sh/rcar-hpbdma.c: In function `hpb_dmae_alloc_chan_resources':
drivers/dma/sh/rcar-hpbdma.c:435: error: implicit declaration of function
`shdma_free_irq'
Fix this compilation error by removing the remaining shdma_free_irq() calls.
Reported-by: Simon Horman <horms@verge.net.au> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is because we returned the error number if the reference of the root was 0
when doing space relocation. It was not right here, because though the root
was dead(refs == 0), but the space it held still need be relocated, or we
could not remove the block group. So in this case, we should return the root
no matter it is dead or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Now we don't drop all the deleted snapshots/subvolumes before the space
balance. It means we have to relocate the space which is held by the dead
snapshots/subvolumes. So we must into them into fs radix tree, or we would
forget to commit the change of them when doing transaction commit, and it
would corrupt the metadata.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Tue, 8 Oct 2013 02:11:09 +0000 (22:11 -0400)]
Btrfs: limit delalloc pages outside of find_delalloc_range
Liu fixed part of this problem and unfortunately I steered him in slightly the
wrong direction and so didn't completely fix the problem. The problem is we
limit the size of the delalloc range we are looking for to max bytes and then we
try to lock that range. If we fail to lock the pages in that range we will
shrink the max bytes to a single page and re loop. However if our first page is
inside of the delalloc range then we will end up limiting the end of the range
to a period before our first page. This is illustrated below
[0 -------- delalloc range --------- 256mb]
[page]
So find_delalloc_range will return with delalloc_start as 0 and end as 128mb,
and then we will notice that delalloc_start < *start and adjust it up, but not
adjust delalloc_end up, so things go sideways. To fix this we need to not limit
the max bytes in find_delalloc_range, but in find_lock_delalloc_range and that
way we don't end up with this confusion. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Wed, 9 Oct 2013 16:24:04 +0000 (12:24 -0400)]
Btrfs: use right root when checking for hash collision
btrfs_rename was using the root of the old dir instead of the root of the new
dir when checking for a hash collision, so if you tried to move a file into a
subvol it would freak out because it would see the file you are trying to move
in its current root. This fixes the bug where this would fail
Cc: stable@vger.kernel.org Reported-by: Chris Murphy <lists@colorremedies.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Kent Overstreet [Fri, 11 Oct 2013 00:31:15 +0000 (17:31 -0700)]
bcache: Fix a null ptr deref regression
Commit c0f04d88e46d ("bcache: Fix flushes in writeback mode") was fixing
a reported data corruption bug, but it seems some last minute
refactoring or rebasing introduced a null pointer deref.
Signed-off-by: Kent Overstreet <kmo@daterainc.com> Cc: linux-stable <stable@vger.kernel.org> # >= v3.10 Reported-by: Gabriel de Perthuis <g2p.code@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fengguang Wu [Wed, 9 Oct 2013 01:26:21 +0000 (09:26 +0800)]
kobject: show debug info on delayed kobject release
Useful for locating buggy drivers on kernel oops.
It may add dozens of new lines to boot dmesg. DEBUG_KOBJECT_RELEASE is
hopefully only enabled in debug kernels (like maybe the Fedora rawhide
one, or at developers), so being a bit more verbose is likely ok.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
watchdog: hpwdt: Patch to ignore auxilary iLO devices
This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Tested-by: Lisa Mitchell <lisa.mitchell@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Thu, 10 Oct 2013 19:31:43 +0000 (12:31 -0700)]
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"These patches are designed to enable improvements to /dev/random for
non-x86 platforms, in particular MIPS and ARM"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: allow architectures to optionally define random_get_entropy()
random: run random_int_secret_init() run after all late_initcalls
Linus Torvalds [Thu, 10 Oct 2013 18:33:02 +0000 (11:33 -0700)]
Merge tag 'spi-v3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"This is all driver updates, mostly fixes for error handling paths
except for the s3c64xx and hspi fixes for trying to use runtime PM
before it is enabled and the pxa2xx fix for interactions between power
management and interrupt handling"
* tag 'spi-v3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix incorrect error path
spi/hspi: fixup Runtime PM enable timing
spi/s3c64xx: Ensure runtime PM is enabled prior to registration
spi/clps711x: drop clk_put for devm_clk_get in spi_clps711x_probe()
spi: fix return value check in dspi_probe()
spi: mpc512x: fix error return code in mpc512x_psc_spi_do_probe()
spi: clps711x: Don't call kfree() after spi_master_put/spi_unregister_master
spi/pxa2xx: check status register as well to determine if the device is off
random: allow architectures to optionally define random_get_entropy()
Allow architectures which have a disabled get_cycles() function to
provide a random_get_entropy() function which provides a fine-grained,
rapidly changing counter that can be used by the /dev/random driver.
For example, an architecture might have a rapidly changing register
used to control random TLB cache eviction, or DRAM refresh that
doesn't meet the requirements of get_cycles(), but which is good
enough for the needs of the random driver.
projects / karo-tx-linux.git / log