Simplify snd_pcm_drain() implementation and avoid unneeded array-
allocation for waitqueues. Instead, one waitqueue is used for the
first draining stream, and wait until all streams finished.
* fix/asoc:
ASoC: remove unused #include <linux/version.h>
ASoC: S3C lrsync function made to work with IRQs disabled.
ASoC: Fix display of stream name in DAPM debugfs
ASoC: Clean up error handling in MPC5200 DMA setup
The headphone and speaker mixer elements aren't properly set for
MSI GX620 with targa-8ch-dig quirk.
Also fixed the speaker volume control for other ALC883-targa quirks,
too.
ASoC: S3C lrsync function made to work with IRQs disabled.
s3c2412_snd_lrsync() maybe reached with IRQs disabled and if LRCLK
is dead due to improper initialization of CPU or CODEC, the system
gets stuck in the loop because jiffies may never get updated.
Implemented counter based wait mechanism for atleast the same
timeout period.
Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unnecessary (and buggy) init sequences left for IDT92HD83*
codecs in the previous fixes. The DACs are now dynamically connected,
thus shouldn't be set statically in init verbs. Also, the mono_nid
is detected dynamically, thus shouldn't be set staticaly, too.
Add the quirk entry for HP dv6. Also add a workaround for the headphone
detection by setting hp_detect=1 beforehand. Without this, the driver
won't do auto-muting because BIOS doesn't give any HP pin but only a
line-out pin.
ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
It's possible that hp_detect is set even though no headphone pin is
detected. The driver issues, however, an unsol event only to hp_pins[0],
which can be invalid.
This patch adds the check of the valid pin to send an unsol event
at initialization and resume callbacks.
IDT92HD73xx and STAC927x codecs use GPIO0 bit as EAPD on many machines.
However, currently we don't set it unless the model is specified just
for safety reason. But, most machines do need this bit, so this safety
handling is rather annoying.
This patch enables GPIO0 setup as default for them. Many HP / Dell
laptops should work even without model override with this change.
* topic/usb-audio:
ALSA: usb-audio - Fix types taken in min()
sound: usb-audio: do not make URBs longer than sync packet interval
sound: usb-audio: add MIDI drain callback
sound: usb-audio: use multiple output URBs
sound: usb-audio: use multiple input URBs
sound: usb-audio: Xonar U1 digital output support
* topic/tlv-minmax:
ALSA: usb-audio - Correct bogus volume dB information
ALSA: usb-audio - Use the new TLV_DB_MINMAX type
ALSA: Add new TLV types for dBwith min/max
Merge branch 'topic/soundcore-preclaim' into for-linus
* topic/soundcore-preclaim:
sound: make OSS device number claiming optional and schedule its removal
sound: request char-major-* module aliases for missing OSS devices
chrdev: implement __[un]register_chrdev()
* topic/oss:
ALSA: allocation may fail in snd_pcm_oss_change_params()
sound: vwsnd: Fix setting of cfgval and ctlval in li_setup_dma()
sound: fix OSS MIDI output data loss
* topic/hda: (92 commits)
ALSA: hda - Use auto model for HP laptops with ALC268 codec
ALSA: hda/realtek: Added support for CLEVO M540R subsystem, 6 channel + digital
ALSA: hda - Add support of Alienware M17x laptop
ALSA: hda - Remove dead codes from patch_sigmatel.c
ALSA: hda - Fix input source selection of IDT92HD73xx
ALSA: hda - Fix obsolete CONFIG_SND_DEBUG_DETECT
ALSA: hda - Unmute docking line-out as default with AD1984A codec
ALSA: hda - Add another entry for Nvidia HDMI device
ALSA: hda - Add missing GPIO initialization for AD1984A laptop model
ALSA: hda - Add support of docking auto-mute/mic for AD1984A laptop model
ALSA: hda - Fix ALC268/ALC269 headphone pin routing
ALSA: hda - Create "Digital Mic Capture Volume" correctly for IDT codecs
ALSA: hda - Add more quirk for HP laptops with AD1984A
ALSA: hda - Add / fix model entries for HD-audio driver
ALSA: hda - Add full audio support on Acer Aspire 7730G notebook
ALSA: hda - Improve auto-cfg mixer name for ALC662
ALSA: hda - Improve auto-cfg mixer name for ALC861-VD
ALSA: hda - Improve auto-cfg mixer name for ALC262
ALSA: hda - Improve auto-cfg mixer name for ALC260
ALSA: hda - Improve auto-cfg mixer name for ALC880
...
* topic/asoc: (226 commits)
ASoC: au1x: PSC-AC97 bugfixes
ASoC: Fix WM835x Out4 capture enumeration
ASoC: Remove unuused hw_read_t
ASoC: fix pxa2xx-ac97.c breakage
ASoC: Fully specify DC servo bits to update in wm_hubs
ASoC: Debugged improper setting of PLL fields in WM8580 driver
ASoC: new board driver to connect bfin-5xx with ad1836 codec
ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI
ASoC: davinci: i2c device creation moved into board files
ASoC: Don't reconfigure WM8350 FLL if not needed
ASoC: Fix s3c-i2s-v2 build
ASoC: Make platform data optional for TLV320AIC3x
ASoC: Add S3C24xx dependencies for Simtec machines
ASoC: SDP3430: Fix TWL GPIO6 pin mux request
ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time
ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop
ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI
OMAP: McBSP: Use textual values in DMA operating mode sysfs files
ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510
ASoC: Select core DMA when building for S3C64xx
...
"This seems to generate /sys/block/$device/queue and its contents for
everyone who is using queues, not just for those queues that have a
non-NULL queue->request_fn."
Note that embedding a queue inside another object has always been
an illegal construct, since the queues are reference counted and
must persist until the last reference is dropped. So aoe was
always buggy in this respect (Jens).
Signed-off-by: Ed Cashin <ecashin@coraid.com> Cc: Andy Whitcroft <apw@canonical.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Bruno Premont <bonbons@linux-vserver.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
i915: disable interrupts before tearing down GEM state
Reinette Chatre reports a frozen system (with blinking keyboard LEDs)
when switching from graphics mode to the text console, or when
suspending (which does the same thing). With netconsole, the oops
turned out to be
BUG: unable to handle kernel NULL pointer dereference at 0000000000000084
IP: [<ffffffffa03ecaab>] i915_driver_irq_handler+0x26b/0xd20 [i915]
and it's due to the i915_gem.c code doing drm_irq_uninstall() after
having done i915_gem_idle(). And the i915_gem_idle() path will do
but if an i915 interrupt comes in after this stage, it may want to
access that hw_status_page, and gets the above NULL pointer dereference.
And since the NULL pointer dereference happens from within an interrupt,
and with the screen still in graphics mode, the common end result is
simply a silently hung machine.
Fix it by simply uninstalling the irq handler before idling rather than
after. Fixes
Manuel Lauss [Tue, 8 Sep 2009 17:45:17 +0000 (19:45 +0200)]
ASoC: au1x: PSC-AC97 bugfixes
This patch fixes the following bugs:
- only reprogram bitdepth if it has changed since last call to hw_params.
- add locking inside ac97_read/write functions:
When reprogramming sample depth, the ac97 unit has to be disabled,
which should not be done in the middle of codec register accesses.
- retry timed-out codec register accesses.
- wait for status bits to set/clear when starting/stopping various
functional blocks; very important after reenabling AC97 unit else
sound may be distorted (e.g. high-pitch noise in 1kHz sine wave).
Zhenyu Wang [Tue, 8 Sep 2009 06:52:25 +0000 (14:52 +0800)]
drm/i915: fix mask bits setting
eDP is exclusive connector too, and add missing crtc_mask
setting for TV.
This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=14139
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Reported-and-tested-by: Carlos R. Mafra <crmafra2@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ALSA: hda - Use auto model for HP laptops with ALC268 codec
The HP laptops with ALC268 codec seem working better with model=auto
than model=toshiba; e.g. the auto model fixes missing digital outputs.
Let's fix quirk entry to choose auto model explicitly.
Sophie Hamilton [Tue, 8 Sep 2009 08:58:42 +0000 (10:58 +0200)]
ALSA: cs46xx - Fix minimum period size
Fix minimum period size for cs46xx cards. This fixes a problem in the
case where neither a period size nor a buffer size is passed to ALSA;
this is the case in Audacious, OpenAL, and others.
Signed-off-by: Sophie Hamilton <kernel@theblob.org> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
agp/intel: support for new chip variant of IGDNG mobile
drm/i915: Unref old_obj on get_fence_reg() error path
drm/i915: increase default latency constant (v2 w/comment)
Clemens Ladisch [Mon, 7 Sep 2009 08:18:54 +0000 (10:18 +0200)]
sound: oxygen: work around MCE when changing volume
When the volume is changed continuously (e.g., when the user drags a
volume slider with the mouse), the driver does lots of I2C writes.
Apparently, the sound chip can get confused when we poll the I2C status
register too much, and fails to complete a read from it. On the PCI-E
models, the PCI-E/PCI bridge gets upset by this and generates a machine
check exception.
To avoid this, this patch replaces the polling with an unconditional
wait that is guaranteed to be long enough.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Johann Messner <johann.messner at jku.at> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of allocating the real buffers, use a fake buffer and ignore
read/write in the dummy driver so that we can save the resources.
For mmap, a single page (unique to the direction, though) is reused
to all buffers.
When the app requires to read/write the real buffers, pass fake_buffer=0
module option at loading time. This will get back to the old behavior.
Dave Airlie [Mon, 7 Sep 2009 05:26:19 +0000 (15:26 +1000)]
drm/radeon/kms: add LTE/GTE discard + rv515 two sided stencil register.
This adds some rv350+ register for LTE/GTE discard,
and enables the rv515 two sided stencil register.
It also disables the DEPTHXY_OFFSET register which
can be used to workaround the CS checker.
Moves rs690 to proper place in rs600 and uses correct
table on rs600.
breaks the build of the gianfar driver because "dev" is undefined in
this function. To quickly test rc9 I changed this to priv->ndev but I do
not know if this is the correct one.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc: Fix i8259 interrupt driver kernel crash on ML510
This patch fixes a null pointer exception caused by removal of
'ack()' for level interrupts in the Xilinx interrupt driver. A recent
change to the xilinx interrupt controller removed the ack hook for
level irqs.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm snapshot: fix on disk chunk size validation
dm exception store: split set_chunk_size
dm snapshot: fix header corruption race on invalidation
dm snapshot: refactor zero_disk_area to use chunk_io
dm log: userspace add luid to distinguish between concurrent log instances
dm raid1: do not allow log_failure variable to unset after being set
dm log: remove incorrect field from userspace table output
dm log: fix userspace status output
dm stripe: expose correct io hints
dm table: add more context to terse warning messages
dm table: fix queue_limit checking device iterator
dm snapshot: implement iterate devices
dm multipath: fix oops when request based io fails when no paths
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix bootup with mcount in some configs.
sparc64: Kill spurious NMI watchdog triggers by increasing limit to 30 seconds.
Nicolas Pitre [Sat, 5 Sep 2009 04:25:37 +0000 (00:25 -0400)]
ext2: fix unbalanced kmap()/kunmap()
In ext2_rename(), dir_page is acquired through ext2_dotdot(). It is
then released through ext2_set_link() but only if old_dir != new_dir.
Failing that, the pkmap reference count is never decremented and the
page remains pinned forever. Repeat that a couple times with highmem
pages and all pkmap slots get exhausted, and every further kmap() calls
end up stalling on the pkmap_map_wait queue at which point the whole
system comes to a halt.
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: ocfs2_write_begin_nolock() should handle len=0
ocfs2: invalidate dentry if its dentry_lock isn't initialized.
pty: don't limit the writes to 'pty_space()' inside 'pty_write()'
The whole write-room thing is something that is up to the _caller_ to
worry about, not the pty layer itself. The total buffer space will
still be limited by the buffering routines themselves, so there is no
advantage or need in having pty_write() artificially limit the size
somehow.
And what happened was that the caller (the n_tty line discipline, in
this case) may have verified that there is room for 2 bytes to be
written (for NL -> CRNL expansion), and it used to then do those writes
as two single-byte writes. And if the first byte written (CR) then
caused a new tty buffer to be allocated, pty_space() may have returned
zero when trying to write the second byte (LF), and then incorrectly
failed the write - leading to a lost newline character.
This should finally fix
http://bugzilla.kernel.org/show_bug.cgi?id=14015
Reported-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When translating CR to CRNL in the n_tty line discipline, we did it as
two tty_put_char() calls. Which works, but is stupid, and has caused
problems before too with bad interactions with the write_room() logic.
The generic USB serial driver had that problem, for example.
Now the pty layer had similar issues after being moved to the generic
tty buffering code (in commit d945cb9cce20ac7143c2de8d88b187f62db99bdc:
"pty: Rework the pty layer to use the normal buffering logic").
So stop doing the silly separate two writes, and do it as a single write
instead. That's what the n_tty layer already does for the space
expansion of tabs (XTABS), and it means that we'll now always have just
a single write for the CRNL to match the single 'tty_write_room()' test,
which hopefully means that the next time somebody screws up buffering,
it won't cause weeks of debugging.
But the root of the problem lies in the fact that do_execve() path calls
tracehook_report_exec() which can stop if the tracer sets PT_TRACE_EXEC.
The tracee must not sleep in TASK_TRACED holding this mutex. Even if we
remove ->cred_guard_mutex from mm_for_maps() and proc_pid_attr_write(),
another task doing PTRACE_ATTACH should not hang until it is killed or the
tracee resumes.
With this patch do_execve() does not use ->cred_guard_mutex directly and
we do not hold it throughout, instead:
- introduce prepare_bprm_creds() helper, it locks the mutex
and calls prepare_exec_creds() to initialize bprm->cred.
- install_exec_creds() drops the mutex after commit_creds(),
and thus before tracehook_report_exec()->ptrace_stop().
or, if exec fails,
free_bprm() drops this mutex when bprm->cred != NULL which
indicates install_exec_creds() was not called.
Reported-by: Tom Horsley <tom.horsley@att.net> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: James Morris <jmorris@namei.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page-allocator: always change pageblock ownership when anti-fragmentation is disabled
On low-memory systems, anti-fragmentation gets disabled as fragmentation
cannot be avoided on a sufficiently large boundary to be worthwhile. Once
disabled, there is a period of time when all the pageblocks are marked
MOVABLE and the expectation is that they get marked UNMOVABLE at each call
to __rmqueue_fallback().
However, when MAX_ORDER is large the pageblocks do not change ownership
because the normal criteria are not met. This has the effect of
prematurely breaking up too many large contiguous blocks. This is most
serious on NOMMU systems which depend on high-order allocations to boot.
This patch causes pageblocks to change ownership on every fallback when
anti-fragmentation is disabled. This prevents the large blocks being
prematurely broken up.
This is a fix to commit 49255c619fbd482d704289b5eb2795f8e3b7ff2e [page
allocator: move check for disabled anti-fragmentation out of fastpath] and
the problem affects 2.6.31-rc8.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Tested-by: Paul Mundt <lethal@linux-sh.org> Cc: David Howells <dhowells@redhat.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Acked-by: Greg Ungerer <gerg@snapgear.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Sat, 5 Sep 2009 18:17:07 +0000 (11:17 -0700)]
nommu: fix error handling in do_mmap_pgoff()
Fix the error handling in do_mmap_pgoff(). If do_mmap_shared_file() or
do_mmap_private() fail, we jump to the error_put_region label at which
point we cann __put_nommu_region() on the region - but we haven't yet
added the region to the tree, and so __put_nommu_region() may BUG
because the region tree is empty or it may corrupt the region tree.
To get around this, we can afford to add the region to the region tree
before calling do_mmap_shared_file() or do_mmap_private() as we keep
nommu_region_sem write-locked, so no-one can race with us by seeing a
transient region.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Acked-by: Paul Mundt <lethal@linux-sh.org> Cc: Mel Gorman <mel@csn.ul.ie> Acked-by: Greg Ungerer <gerg@snapgear.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cancel_delayed_work() has to use del_timer_sync() to guarantee the timer
function is not running after return. But most users doesn't actually
need this, and del_timer_sync() has problems: it is not useable from
interrupt, and it depends on every lock which could be taken from irq.
Introduce __cancel_delayed_work() which calls del_timer() instead.
The immediate reason for this patch is
http://bugzilla.kernel.org/show_bug.cgi?id=13757
but hopefully this helper makes sense anyway.
As for 13757 bug, actually we need requeue_delayed_work(), but its
semantics are not yet clear.
Merge this patch early to resolves cross-tree interdependencies between
input and infiniband.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Roland Dreier <rdreier@cisco.com> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Richter [Thu, 3 Sep 2009 21:07:35 +0000 (23:07 +0200)]
firewire: sbp2: fix freeing of unallocated memory
If a target writes invalid status (typically status of a command that
already timed out), firewire-sbp2 attempts to put away an ORB that
doesn't exist. https://bugzilla.redhat.com/show_bug.cgi?id=519772
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Fri, 28 Aug 2009 11:26:03 +0000 (13:26 +0200)]
firewire: ohci: fix Ricoh R5C832, video reception
In dual-buffer DMA mode, no video frames are ever received from R5C832
by libdc1394. Fallback to packet-per-buffer DMA works reliably.
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/13393/focus=13476
Reported-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Fri, 28 Aug 2009 11:25:15 +0000 (13:25 +0200)]
firewire: ohci: fix Agere FW643 and multiple cameras
An Agere FW643 OHCI 1.1 card works fine for video reception from one
camera but fails early if receiving from two cameras. After a short
while, no IR IRQ events occur and the context control register does not
react anymore. This happens regardless whether both IR DMA contexts are
dual-buffer or one is dual-buffer and the other packet-per-buffer.
This can be worked around by disabling dual buffer DMA mode entirely.
http://sourceforge.net/mailarchive/message.php?msg_name=4A7C0594.2020208%40gmail.com
(Reported by Samuel Audet.)
In another report (by Jonathan Cameron), an FW643 works OK with two
cameras in dual buffer mode. Whether this is due to different chip
revisions or different usage patterns (different video formats) is not
yet clear. However, as far as the current capabilities of
firewire-core's isochronous I/O interface are concerned, simply
switching off dual-buffer on non-working and working FW643s alike is not
a problem in practice. We only need to revisit this issue if we are
going to enhance the interface, e.g. so that applications can explicitly
choose modes.
Reported-by: Samuel Audet <samuel.audet@gmail.com> Reported-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
As David Moore noted, a previously correct sizeof() expression became
wrong since the commit changed its argument from an array to a pointer.
This resulted in an oops in ohci_cancel_packet in the shared workqueue
thread's context when an isochronous resource was to be freed.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix some problems seen in the chunk size processing when activating a
pre-existing snapshot.
For a new snapshot, the chunk size can either be supplied by the creator
or a default value can be used. For an existing snapshot, the
chunk size in the snapshot header on disk should always be used.
If someone attempts to load an existing snapshot and has the 'default
chunk size' option set, the kernel uses its default value even when it
is incorrect for the snapshot being loaded. This patch ensures the
correct on-disk value is always used.
Secondly, when the code does use the chunk size stored on the disk it is
prudent to revalidate it, so the code can exit cleanly if it got
corrupted as happened in
https://bugzilla.redhat.com/show_bug.cgi?id=461506 .
projects / linux-beck.git / log