powerpc/85xx: P3041DS - change espi input-clock from 40MHz to 35MHz
Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 13 Jul 2012 22:40:43 +0000 (17:40 -0500)]
powerpc/85xx: remove P1020RDB and P2020RDB CAMP device trees
We only need two examples of CAMP device trees in the upstream kernel.
Co-operative Asymmetric Multi-Processing (CAMP) is a technique where two
or more operating systems (typically multiple copies of the same Linux
kernel) are loaded into memory, and each kernel is given a subset of the
available cores to execute on. For example, on a four-core system, one
kernel runs on cores 0 and 1, and the other runs on cores 2 and 3.
The devices are also partitioned among the operating systems, and this is
done with customized device trees. Each kernel gets its own device tree
that has only the devices that it should know about.
Unfortunately, this approach is very hackish. The kernels are trusted to
only access devices in their respective device trees, and the partitioning
only works for devices that can be handled. Crafting the device trees is a
tricky process, and getting U-Boot to load and start all kernels is
cumbersome.
But most importantly, each CAMP setup is very application-specific, since
the actual partitioning of resources is done in the DTS by the system
designer. Therefore, it doesn't make a lot of sense to have a lot of CAMP
device trees, since we only expect them to be used as examples.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 13 Jul 2012 19:28:42 +0000 (14:28 -0500)]
powerpc/85xx: p1022ds: disable the NAND flash node if video is enabled
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/eeh: Check handle_eeh_events() return value
Function eeh_event_handler() dereferences the pointer returned by
handle_eeh_events() without checking, causing a crash if NULL was
returned, which is expected in some situations.
This patch fixes this bug by checking for the value returned by
handle_eeh_events() before dereferencing it.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@vger.kernel.org [v3.4+]
powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS
In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.
For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Wed, 11 Jul 2012 00:26:48 +0000 (19:26 -0500)]
powerpc/e500: add paravirt QEMU platform
This gives the kernel a paravirtualized machine to target, without
requiring both sides to pretend to be targeting a specific board
that likely has little to do with the host in KVM scenarios. This
avoids the need to add new boards to QEMU just to be able to
run KVM on new CPUs.
As this is the first platform that can run with either e500v2 or
e500mc, CONFIG_PPC_E500MC is now a legitimately user configurable
option, so add a help text.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Wed, 11 Jul 2012 00:26:49 +0000 (19:26 -0500)]
powerpc/mpc85xx_ds: convert to unified PCI init
Similar to how the primary PCI bridge is identified by looking
for an isa subnode, we determine whether to apply uli exclusions
by looking for a uli subnode.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Wed, 11 Jul 2012 00:26:47 +0000 (19:26 -0500)]
powerpc/fsl-pci: get PCI init out of board files
As an alternative incremental starting point to Jia Hongtao's patchset,
get the FSL PCI init out of the board files, but do not yet convert to a
platform driver.
Rather than having each board supply a magic register offset for
determining the "primary" bus, we look for which PCI host bridge
contains an ISA node within its subtree. If there is no ISA node,
normally that would mean there is no primary bus, but until certain
bugs are fixed we arbitrarily designate a primary in this case.
Conversion to a platform driver and related improvements can happen
after this, as the ordering issues are sorted out.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/watchdog: move booke watchdog param related code to setup-common.c
Currently, BOOKE watchdog code for checking "wdt" and "wdt_period" is
in setup_32.c, it cannot be used in 64-bit, so move it to a common place
setup-common.c, which will be shared by 32-bit and 64-bit.
Also, replace the simple_strtoul with kstrtol.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andreas Schwab [Sat, 9 Jun 2012 13:58:56 +0000 (15:58 +0200)]
sound/aoa: Adapt to new i2c probing scheme
The i2c-powermac driver now creates the i2c devices properly
from the device-tree, including workarounds for broken or
missing device-tree bits, so let's just use the normal probe
methods and get rid of the hand made device creation code.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
i2c/powermac: Improve detection of devices from device-tree
This patch adds a number of workarounds for broken Apple device-trees
mostly around sound chips. It handles creating the missing audio codec
devices and works around various issues with missing addresses or
missing compatible properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Haren Myneni [Wed, 11 Jul 2012 05:18:44 +0000 (15:18 +1000)]
powerpc: Disable /dev/port interface on systems without an ISA bridge
Some power systems do not have legacy ISA devices. So, /dev/port is not
a valid interface on these systems. User level tools such as kbdrate is
trying to access the device using this interface which is causing the
system crash.
This patch will fix this issue by not creating this interface on these
powerpc systems.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
prom_update_property() currently fails if the property doesn't
actually exist yet which isn't what we want. Change to add-or-update
instead of update-only, then we can remove a lot duplicated lines.
Suggested-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Put the gpr save/restore functions in their own section
This allows the linker to know that calls to them do not need to switch
TOC and stop errors like the following when linking large configurations:
powerpc64-linux-ld: drivers/built-in.o: In function `.gpiochip_is_requested':
(.text+0x4): sibling call optimization to `_savegpr0_29' does not allow automatic multiple TOCs; recompile with -mminimal-toc or -fno-optimize-sibling-calls, or make `_savegpr0_29' extern
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 4 Jul 2012 20:37:11 +0000 (20:37 +0000)]
powerpc: Add VDSO version of getcpu
We have a request for a fast method of getting CPU and NUMA node IDs
from userspace. This patch implements a getcpu VDSO function,
similar to x86.
Ben suggested we use SPRG3 which is userspace readable. SPRG3 can be
modified by a KVM guest, so we save the SPRG3 value in the paca and
restore it when transitioning from the guest to the host.
I have a glibc patch that implements sched_getcpu on top of this.
Testing on a POWER7:
baseline: 538 cycles
vdso: 30 cycles
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/cpuidle: Fixes for pseries_idle hotplug notifier
Currently the call to pseries_notify_cpuidle_add_cpu(), that takes
action on the cpuidle front when a cpu is added/removed
is being made from smp_xics_setup_cpu().
This caused lockdep issues as
reported https://lkml.org/lkml/2012/5/17/2
On addition of each cpu,
resources were cleared and re-allocated each time, all in critical
section as part of start_secondary() call were interrupts are disabled.
To resolve this issue, the pseries_notify_cpuidle_add_cpu() call is
is being replaced by a hotplug notifier which
would prevent cpuidle resources from being
released and allocated each time cpu is onlined in the critical code path.
It was fixed in https://lkml.org/lkml/2012/5/18/174.
Also it is essential to call cpuidle_enable/disable_device
between cpuidle_pause_and_lock() and
cpuidle_resume_and_unlock() when used externally
to avoid race conditions. Add support for CPU_ONLINE_FROZEN
and CPU_DEAD_FROZEN as part of hotplug notify event for
pseries_idle and unregister hotplug notifier
while exiting out. The above mentioned issues
are fixed as part of this patch.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When I "fixed" the CONFIG_TRACE_IRQFLAGS case on interrupt entry,
I screwed up a little bit with the test for user space vs. kernel.
The code is fine, there's just some dead code around it. I basically
removed the test and always create the added stack frame whether
coming from user or kernel since in any case we do need to save
a bunch of volatile registers or bad things would happen (we can
take page faults in the kernel for example).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Shawn Guo [Fri, 30 Mar 2012 05:38:56 +0000 (13:38 +0800)]
powerpc: select PPC_CLOCK unconditionally for FSL_SOC
Freescale PowerPC SoCs share a number of IP blocks with Freescale
ARM/IMX SoCs, FlexCAN, SSI, FEC, eSDHC, USB, etc. There are some
effort consolidating those drivers to make them work for both
architectures.
One outstanding difference between two architectures is ARM/IMX will
turn off module clocks during platform initialization for power saving
and expects drivers manage clocks using clk API, while PowerPC
mostly does not do that, and thus does not always build in clk API.
Listing all those driver Kconfig options in "select PPC_CLOCK if" seems
not scalable for long term maintenance, and could easily introduce
Kconfig recursive dependency. This patch chooses to select PPC_CLOCK
unconditionally for FSL_SOC to always build clk API for PowerPC in.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kokoris, Ioannis [Fri, 11 Nov 2011 16:05:11 +0000 (17:05 +0100)]
powerpc/qe: set IReady in QE Microcode Upload
QE Microcode Initialization using qe_upload_microcode() does not work on
P1021 if the IRAM-Ready register is not set after the microcode upload. Add
a definition for the "I-RAM Ready" register and sets it upon microcode
upload completion.
Signed-off-by: Ioannis Kokkoris <ioannis.kokoris@siemens-enterprise.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Shaohui Xie [Fri, 11 May 2012 05:33:40 +0000 (13:33 +0800)]
powerpc/watchdog: replace CONFIG_FSL_BOOKE with CONFIG_PPC_FSL_BOOK3E
CONFIG_FSL_BOOKE is only defined in 32-bit, CONFIG_PPC_FSL_BOOK3E is
defined in both 32-bit and 64-bit, so use CONFIG_PPC_FSL_BOOK3E to make
driver work in 32-bit & 64-bit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/mpic: Use the MPIC_LARGE_VECTORS flag for FSL MPIC.
We should use the MPIC_LARG_VECTORS flag while intializing the MPIC.
This prevents us from eating in to hardware vector number space (MSIs)
while setting up internal sources.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Timur Tabi [Thu, 5 Jul 2012 15:08:28 +0000 (10:08 -0500)]
powerpc/85xx: use the BRx registers to enable indirect mode on the P1022DS
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Tue, 26 Jun 2012 19:54:27 +0000 (15:54 -0400)]
powerpc: remove Wind River SBC8560 support
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tang Yuantian [Thu, 24 May 2012 09:08:27 +0000 (17:08 +0800)]
powerpc/85xx: Add P1024rdb dts support
Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tang Yuantian [Thu, 24 May 2012 09:08:28 +0000 (17:08 +0800)]
powerpc/85xx: Add P1024rdb board support
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use
the same platform file as the p1/p2 rdb board.
Overview of P2020RDB platform
- DDR3 1G
- NOR flash 16M
- 3 Ethernet interfaces
- NAND Flash 32M
- SPI EEPROM 16M
- SD/MMC
- 2 USB ports
- 4 TDM ports
Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Gustavo Zacarias [Wed, 23 May 2012 14:35:18 +0000 (11:35 -0300)]
powerpc/p1010rdb: add EEPROMs to device tree
Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Revert "powerpc/85xx: p2020rdb - move the NAND address."
This reverts commit 0c00f65653389a408dfbbee7578e671664eea26a.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Holger Brunck [Tue, 8 May 2012 13:57:22 +0000 (15:57 +0200)]
powerpc/82xx: add SPI support for mgcoge
Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
powerpc/83xx: fix RGMII AC values workaround for km83xx
Fix RGMII workaround code in km83xx.c for MPC8360E and MPC8358E that it
correctly identifes all affected SoC chip models and applies the
workarounds appropriate for 2.0 and 2.1 revisions as per Freescale
MPC8360ECE Errata document Rev.5(9/2011) item QE_ENET10.
Signed-off-by: Christian Herzig <christian.herzig@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jerry Huang [Tue, 17 Apr 2012 01:42:35 +0000 (09:42 +0800)]
powerpc/p1022ds: Add RTC support
Add the RTC support into the p1022ds device tree
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/fsl/pci: Fix when quirk_fsl_pcie_header is freed up
Change quirk_fsl_pcie_header from __init to __devinit to ensure if we
have a runtime access (like via an FPGA being loaded after boot on the
PCIe link) that we dont access randomly freed memory.
Signed-off-by: Matias Garcia <mgarcia@rossvideo.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Blanchard [Sun, 24 Jun 2012 18:24:44 +0000 (18:24 +0000)]
powerpc/vio: Separate vio bus probe and device probe
Similar to PCI, separate the bus probe from device probe. This allows
us to attach bus notifiers for DMA debug and IOMMU fault injection
before devices have been probed.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Tue, 26 Jun 2012 01:02:15 +0000 (01:02 +0000)]
powerpc/perf: Always use pt_regs for userspace samples
At the moment we always use the SIAR if the PMU supports continuous
sampling. Unfortunately the SIAR and the PMU exception are not
synchronised for non marked events so we can end up with callchains
that dont make sense.
The following patch checks the HV and PR bits for samples coming from
userspace and always uses pt_regs for them. Userspace will never have
interrupts off so there is no real advantage to using the SIAR for
non marked events in userspace.
I had experimented with a patch that did a similar thing for kernel
samples but we lost a significant amount of information. I was
unable to profile any of our early exception code for example.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want to access the MMCRA_SIHV and MMCRA_SIPR bits elsewhere so
create mmcra_sihv and mmcra_sipr which hide the differences between
the old and new layout of the bits.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 25 Jun 2012 13:33:21 +0000 (13:33 +0000)]
powerpc: Start using ___PPC_RA/B/S/T where necessary
Now have ___PPC_RA/B/S/T we can use it in some places. These are
places where we can't use the existing defines which will soon enforce
R0-R31 usage.
The macros being changed here are being used in inline asm, which
can't convert to enforce the R0-R31 usage.
bpf_jit uses a mix of both generated and non-generated with the same
code, so just convert all these to use the ___PPC_R versions which
won't enforce R usage later.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 25 Jun 2012 13:33:10 +0000 (13:33 +0000)]
powerpc: Fix usage of register macros getting ready for %r0 change
Anything that uses a constructed instruction (ie. from ppc-opcode.h),
need to use the new R0 macro, as %r0 is not going to work.
Also convert usages of macros where we are just determining an offset
(usually for a load/store), like:
std r14,STK_REG(r14)(r1)
Can't use STK_REG(r14) as %r14 doesn't work in the STK_REG macro since
it's just calculating an offset.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/numa: Avoid stupid uninitialized warning from gcc
Newer gcc are being a bit blind here (it's pretty obvious we don't
reach the code path using the array if we haven't initialized the
pointer) but none of that is performance critical so let's just
silence it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Looks like we still have issues with pSeries and Cell idle code
vs. the lazy irq state. In fact, the reset fixes that went upstream
are exposing the problem more by causing BUG_ON() to trigger (which
this patch turns into a WARN_ON instead).
We need to be careful when using a variant of low power state that
has the side effect of turning interrupts back on, to properly set
all the SW & lazy state to look as if everything is enabled before
we enter the low power state with MSR:EE off as we will return with
MSR:EE on. If not, we have a discrepancy of state which can cause
things to go very wrong later on.
This patch moves the logic into a helper and uses it from the
pseries and cell idle code. The power4/970 idle code already got
things right (in assembly even !) so I'm not touching it. The power7
"bare metal" idle code is subtly different and correct. Remains PA6T
and some hypervisor based Cell platforms which have questionable
code in there, but they are mostly dead platforms so I'll fix them
when I manage to get final answers from the respective maintainers
about how the low power state actually works on them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@vger.kernel.org [v3.4]
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A smallish fix for a lock dependency issue which affects a bunch of
Qualcomm boards that do unusually complicated things with their
regulators, the API is unlikely to be called by any other system."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix recursive mutex lockdep warning
Hans de Goede [Sun, 8 Jul 2012 17:41:14 +0000 (19:41 +0200)]
gspca_sn9c20x: Fix NULL pointer dereference
Don't call v4l2_ctrl_g_ctrl on ctrls which the model cam in question
does not have.
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ Taken directly, since Mauro is on vacation ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
Pull minor virtio-balloon fix from Rusty Russell:
"Theoretical fix, which greatly simplifies upcoming balloon patches
which will go in via some vm tree."
* tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio-balloon: fix add/get API use
Merge tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg
Pull rpmsg fixes from Ohad Ben-Cohen:
"Fixing two (somewhat rare) endpoint-related race issues, both of which
were reported by Fernando Guzman Lugo."
* tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg:
rpmsg: make sure inflight messages don't invoke just-removed callbacks
rpmsg: avoid premature deallocation of endpoints
Merge tag 'hwspinlock-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock fix from Ohad Ben-Cohen:
"A single hwspinlock core fix for multiple hwspinlock devices
scenarios, from Shinya Kuribayashi."
* tag 'hwspinlock-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock/core: use global ID to register hwspinlocks on multiple devices
Merge tag 'iommu-fixes-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The patches fix several issues in the AMD IOMMU driver, the NVidia
SMMU driver, and the DMA debug code.
The most important fix for the AMD IOMMU solves a problem with SR-IOV
devices where virtual functions did not work with IOMMU enabled. The
NVidia SMMU patch fixes a possible sleep while spin-lock situation
(queued the small fix for v3.5, a better but more intrusive fix is
coming for v3.6). The DMA debug patches fix a possible data
corruption issue due to bool vs u32 usage."
* tag 'iommu-fixes-v3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: fix type bug in flush code
dma-debug: debugfs_create_bool() takes a u32 pointer
iommu/tegra: smmu: Fix unsleepable memory allocation
iommu/amd: Initialize dma_ops for hotplug and sriov devices
iommu/amd: Fix missing iommu_shutdown initialization in passthrough mode
Since ee7cd8981e15bcb365fc762afe3fc47b8242f630 'virtio: expose added
descriptors immediately.', in virtio balloon virtqueue_get_buf might
now run concurrently with virtqueue_kick. I audited both and this
seems safe in practice but this is not guaranteed by the API.
Additionally, a spurious interrupt might in theory make
virtqueue_get_buf run in parallel with virtqueue_add_buf, which is
racy.
While we might try to protect against spurious callbacks it's
easier to fix the driver: balloon seems to be the only one
(mis)using the API like this, so let's just fix balloon.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed unused var)
Merge branch 'for-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The previous cgroup pull request contained a patch to fix a race
condition during cgroup hierarchy umount. Unfortunately, while the
patch reduced the race window such that the test case I and Sasha were
using didn't trigger it anymore, it wasn't complete - Shyju and Li
could reliably trigger the race condition using a different test case.
The problem wasn't the gap between dentry deletion and release which
the previous patch tried to fix. The window was between the last
dput() of a root's child and the resulting dput() of the root. For
cgroup dentries, the deletion and release always happen synchronously.
As this releases the s_active ref, the refcnt of the root dentry,
which doesn't hold s_active, stays above zero without the
corresponding s_active. If umount was in progress, the last
deactivate_super() proceeds to destory the superblock and triggers
BUG() on the non-zero root dentry refcnt after shrinking.
This issue surfaced because cgroup dentries are now allowed to linger
after rmdir(2) since 3.5-rc1. Before, rmdir synchronously drained the
dentry refcnt and the s_active acquired by rmdir from vfs layer
protected the whole thing. After 3.5-rc1, cgroup may internally hold
and put dentry refs after rmdir finishes and the delayed dput()
doesn't have surrounding s_active ref exposing this issue.
This pull request contains two patches - one reverting the previous
incorrect fix and the other adding the surrounding s_active ref around
the delayed dput().
This is quite late in the release cycle but the change is on the safer
side and fixes the test cases reliably, so I don't think it's too
crazy."
* 'for-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix cgroup hierarchy umount race
Revert "cgroup: superblock can't be released with active dentries"
vfs: make O_PATH file descriptors usable for 'fchdir()'
We already use them for openat() and friends, but fchdir() also wants to
be able to use O_PATH file descriptors. This should make it comparable
to the O_SEARCH of Solaris. In particular, O_PATH allows you to access
(not-quite-open) a directory you don't have read persmission to, only
execute permission.
Noticed during development of multithread support for ksh93.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # O_PATH introduced in 3.0+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
48ddbe1946 "cgroup: make css->refcnt clearing on cgroup removal
optional" allowed a css to linger after the associated cgroup is
removed. As a css holds a reference on the cgroup's dentry, it means
that cgroup dentries may linger for a while.
Destroying a superblock which has dentries with positive refcnts is a
critical bug and triggers BUG() in vfs code. As each cgroup dentry
holds an s_active reference, any lingering cgroup has both its dentry
and the superblock pinned and thus preventing premature release of
superblock.
Unfortunately, after 48ddbe1946, there's a small window while
releasing a cgroup which is directly under the root of the hierarchy.
When a cgroup directory is released, vfs layer first deletes the
corresponding dentry and then invokes dput() on the parent, which may
recurse further, so when a cgroup directly below root cgroup is
released, the cgroup is first destroyed - which releases the s_active
it was holding - and then the dentry for the root cgroup is dput().
This creates a window where the root dentry's refcnt isn't zero but
superblock's s_active is. If umount happens before or during this
window, vfs will see the root dentry with non-zero refcnt and trigger
BUG().
Before 48ddbe1946, this problem didn't exist because the last dentry
reference was guaranteed to be put synchronously from rmdir(2)
invocation which holds s_active around the whole process.
Fix it by holding an extra superblock->s_active reference across
dput() from css release, which is the dput() path added by 48ddbe1946
and the only one which doesn't hold an extra s_active ref across the
final cgroup dput().
projects / karo-tx-linux.git / log